DATA PROJECTOR
MODEL
PG-F312X
PG-F262X
PG-F212X
OPERATION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-
ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
fuse marked or
and of the same rating as above, which is also indicated on the pin
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
Brown
: Neutral
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol or coloured green or
green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
The supplied CD-ROM contains operation instructions in English, German, French,
Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read
through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch.
Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,
français, espagnol, italien, néerlandais, suédois, portugais, chinois et coréen. Veuillez lire
attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,
franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska och koreanska.
Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,
francés, español, italiano, holandés, sueco, portugués, chino y coreano. Lea
cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,
spagnolo, italiano, olandese, svedese, portoghese, cinese e coreano. Leggere
attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,
Italiaans, Nederlands, Zweeds, Portugees, Chinees en Koreaans. Lees de handleiding
zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Espanhol, Italiano, Holandês, Sueco, Português, Chinês e Coreano. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
1
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the operation manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is
provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount
of mercury. Disposal of these materials may be regulated due to
environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 52.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
E.U. ONLY
Sonninstraße 3, D-20097 Hamburg
2
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
•
In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons
(P/R/O/Q)
Buttons used in
this operation
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU/HELP button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
Button used in
this step
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu for
COMPUTER (RGB) input
Press MENU/HELP.
1
2
• The “Picture” menu screen for the se-
lected input mode is displayed.
Menu item
Press Q or O and select“Picture”
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
to adjust.
Picture Mode
Contrast
Bright
0
0
0
0
0
1
Red
On-screen
display
Blue
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
On
DNR
Off
Lamp Setting
Reset
Bright
SEL./ADJ.
ENTER
END
38
Info
Note
........Indicates safeguards for using the projector.
.........Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
Troubleshooting
Index
P. 49
PP. 64 and 65
P. 69
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Preparing
Introduction
Useful Features
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Operation
Manuals .............................................. 9
Accessories ........................................ 10
Part Names and Functions ................. 11
Projector ............................................... 11
Rear View ............................................. 12
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Operating with the Remote Control.... 32
Displaying and Setting the
Break Timer........................................ 32
Displaying the Pointer .......................... 32
Using the Spot Function ...................... 32
Switching the Eco+Quiet Mode ........... 32
Auto Sync (Auto Sync Adjustment) ..... 33
Freezing a Moving Image .................... 33
Selecting the Picture Mode .................. 33
Displaying an Enlarged Portion of
an Image ............................................ 33
Using the Remote Control as the
Wireless Computer Mouse ................ 34
Menu Items ......................................... 35
Using the Menu Screen ...................... 38
Menu Selections (Adjustments) ........... 38
Picture Adjustment (“Picture” Menu) ... 40
Selecting the Picture Mode .................. 40
Adjusting the Image ............................. 41
Adjusting the Color Temperature ......... 41
Adjusting the Colors............................. 41
Progressive ........................................... 42
Reducing Image Noise (DNR) ............. 42
Lamp Setting ........................................ 42
Adjusting the Projector Image
(“SCR - ADJ” Menu) ......................... 43
Setting the Resize Mode ...................... 43
Adjusting the Image Position ............... 43
Keystone Correction ............................ 43
Setting the On-screen Display ............. 43
Closed Caption .................................... 44
Selecting the Background Image ........ 44
Selecting the Setup Guide ................... 44
Reversing/Inverting Projected
Quick Start
Quick Start .......................................... 16
Setup and Projection ............................ 16
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Screen Size and Projection Distance .. 20
Connections
Connecting the Projector to
Other Equipment .............................. 21
Controlling the Projector by
a Computer....................................... 24
Connecting the Power Cord ............... 24
Images ............................................... 44
Selecting the On-screen Display
Language........................................... 44
Adjusting the Projector Function
Using
(“PRJ - ADJ” Menu) .......................... 45
Auto Sync (Auto Sync Adjustment) ..... 45
Auto Power Off Function ...................... 45
Auto Restart Function .......................... 45
STANDBY Mode ................................... 45
Setting the Confirmation Sound
Basic Operation
Turning the Projector On/Off .............. 25
Turning the Projector on ....................... 25
Turning the Power off (Putting the
Projector into Standby Mode) ........... 25
Image Projection................................. 26
About the Setup Guide ........................ 26
Adjusting the Projected Image ............ 26
Correcting Trapezoidal Distortion ........ 28
Switching the Input Mode .................... 29
Adjusting the Volume ........................... 29
Displaying the Black Screen and
(System Sound) ................................. 45
Speaker Setting .................................... 45
Audio Input ........................................... 46
Selecting the Transmission Speed
(RS-232C) .......................................... 46
Fan Mode Setting ................................. 46
System Lock Function .......................... 46
Checking the Lamp Life Status ........... 47
Keylock Function .................................. 47
Turning off the Sound Temporarily .... 29
Resize Mode......................................... 30
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting with the
“Help” Menu ...................................... 48
Utilizing the “Help” Menu Functions .... 48
Reference
Appendix
Maintenance ....................................... 49
Maintenance Indicators ...................... 50
Regarding the Lamp ........................... 52
Lamp..................................................... 52
Caution Concerning the Lamp ............ 52
Replacing the Lamp ............................. 52
Removing and Installing the
Lamp Unit .......................................... 53
Resetting the Lamp Timer.................... 54
Storing the Projector........................... 55
How to Use the Storage Case ............. 55
Connecting Pin Assignments ............. 56
RS-232C Specifications and
Commands ....................................... 58
Computer Compatibility Chart ............ 63
Troubleshooting .................................. 64
For SHARP Assistance ...................... 66
Specifications ..................................... 67
Dimensions ......................................... 68
Index ................................................... 69
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
CAUTION:Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
10. Ventilation
Slots and openings in the cabinet are provided
All the safety and operating instructions should
be read before the product is operated.
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
11. Power Sources
5. Cleaning
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. Accessories
b. Three-wire grounding type (mains) plug with
a grounding terminal.
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
9. Transportation
14. Lightning
A
product and cart
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Overloading
19. Replacement Parts
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
22. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for
service.
• DLP® and the DLP logo are registered trademarks ofTexas Instruments and BrilliantColorTM
is a trademark of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass par-
ticles if lamp ruptures.In case
of lamp rupture, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center for replacement.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
See “Replacing the Lamp” on
page 52.
Warning about placing the projector in
a high position
■ When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector fall-
ing down.
Caution concerning the setup of the
projector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and cigarette smoke.When the
projector is subjected to these environments,
the vents and lens must be cleaned more of-
ten. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the adjust-
ment foot.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion.(See pages 50 and 51.) Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projec-
tor is used for a while.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution regarding usage of the projector Using the projector in other countries
■ If you are not to use the projector for a long ■ The power supply voltage and the shape of
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other cables
connected to it.
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
■ If the power cord is unplugged while the
cooling fan is running, some parts of the
projector may still be hot. Use caution when
handling the projector.
Temperature monitor function
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you at-
tach the lens cap to the projector. (See page
11.)
■ Do not expose the projector to direct sunlight
or place next to heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
■
If the projector starts to overheat due to setup
problems or blockage of the air vents, “ ” and
” will illuminate in the lower left corner
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warn-
ing indicator on the projector will blink, and after
a 60-second cooling-off period the projector will
enter standby mode. Refer to “Maintenance In-
dicators” on page 50 for details.
“
Other connected equipment
■ When connecting a computer or other audio-
visual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the operation manuals of the pro-
jector and the equipment to be connected for
instructions on how to make the connections.
Info
•
The cooling fan regulates the internal tem-
perature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in
the fan speed. This does not indicate
malfunction.
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To uti-
lize these manuals, you need to install Adobe® Reader® on your computer (Win-
dows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows® (For Macintosh®, skip step 2).
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the “MANUALS” folder.
5 Double click the model (name of the folder)
that you want to view.
6 Double click the language (name of the
folder) that you want to view.
7 Double click the pdf file to access the pro-
jector manuals.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first,
then specify the desired file using the “File”, “Open” menu.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA045WJPZ>
Lens cap (attached)
<CCAPHA027WJSA>
Remote control
<RRMCGA662WJSA>
DIN-D-sub RS-232C adaptor
Storage case
<GCASNA021WJSA>
(5 57/64" (15 cm))
<QCNWGA091WJPZ>
Power cord*
(1)
(2)
(3)
(4)
For U.S. and
Canada, etc.
(6' (1.8 m))
For Europe,
For U.K. and
For Australia, New
Zealand and Oceania
(6' (1.8 m))
except U.K.
Singapore
(6' (1.8 m))
(6' (1.8 m))
<QACCDA007WJPZ> <QACCVA011WJPZ> <QACCBA036WJPZ> <QACCLA018WJPZ>
* Use the power cord that corresponds to the wall outlet in your country.
• Operation manual (this manual <TINS-D519WJZZ> and CD-ROM <UDSKAA098WJZZ>)
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
■ Lamp unit
AN-F212LP
■ Ceiling-mount adaptor
AN-60KT
AN-XRCM30 (for U.S.A. only)
■ Ceiling-mount unit
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))
AN-MR2
AN-C3CP2
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Projector
Top View
Power
indicator
Lamp indicator
25, 50
25, 50
Temperature warning
indicator
50
32
STANDBY/ON
button
ECO+QUIET button
For lowering the noise
of the cooling fan and
extending the lamp life.
25
For turning the
power on and
putting the
projector into
standby mode.
VOL (Volume) buttons
(–O/Q+)
For adjusting the
speaker sound level.
29
29
ENTER button
For setting
items selected
or adjusted on
the menu.
38
28
INPUT buttons (P/R)
For switching input mode.
MENU/HELP button
For displaying
37, 46
adjustment and
setting screens, and
help screen.
KEYSTONE
button
For entering the
Keystone
Correction mode.
Adjustment buttons
(P/R/O/Q)
37
For selecting menu items.
Front View
Zoom ring
For enlarging/
reducing the picture.
26
Intake vent
Remote control
sensor
49
15
Speaker
45
Exhaust vent
49
Focus ring
For adjusting
the focus.
26
HEIGHT
ADJUST lever
27
Push both sides of the lens cap
to attach or remove.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Rear View
Terminals
AUDIO 1 input terminal
S-VIDEO input terminal
Terminal for connecting
video equipment with an
S-video terminal.
22
23
21
COMPUTER/
COMPONENT input
terminal
22
RS-232C terminal
Terminal for
24
Terminal for computer RGB
and component signals.
controlling the
projector using a
computer.
DVI-I input
terminal
Terminal for
DVI digital,
21
22
USB terminal
34
Terminal connecting
with the USB
terminal on the
computer RGB
and component
signals.
computer for using
the supplied remote
control as the
computer mouse.
AUDIO OUT
terminal
23
AUDIO 2 input
terminal
23
Audio output terminal of
equipment connected to the
audio input terminal.
VIDEO input
terminal
Terminal for
connecting video
equipment.
22
MONITOR OUT
terminal
(Output terminal for computer RGB,
component and DVI analog signals. Shared
for COMPUTER/COMPONENT and DVI-I)
Terminal for connecting a monitor.
23
AC socket
Connect the supplied
power cord.
24
Rear
adjustment
foot
27
Kensington Security
Standard connector
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY button
ON button
For turning the power
on.
25
25
For putting the projector
into the standby mode.
FREEZE button
For freezing images.
33
29
COMPUTER, DVI,
29
S-VIDEO, VIDEO buttons
For switching to the
respective input modes.
AV MUTE button
For temporarily
displaying a black
screen and turning
off the sound.
BREAK TIMER button
For displaying the
break time.
32
VOL +/– (Volume)
buttons
For adjusting the
speaker sound level.
29
MAGNIFY buttons
For enlarging/reducing
part of the image.
33
PAGE UP/PAGE
DOWN buttons
34
SPOT button
For displaying the
spotlight.
32
38
Same as the [Page Down] and
[Page Up] keys on a computer
keyboard, when with the USB
connection (using a USB cable
or the optional remote
ENTER button
For setting items
selected or adjusted
on the menu.
receiver).
POINTER button
For displaying the
pointer.
32
R-CLICK/RETURN
button
34
38
• For the Right click
when with the USB
connection (using a
USB cable or the
optional remote
receiver).
• For returning to the
previous menu screen
during menu
MOUSE/Adjustment
buttons (P/R/O/Q)
• For moving the
computer cursor when with the USB
connection (using a USB cable or the
optional remote receiver).
• For selecting and adjusting menu
items.
34
38
operations.
L-CLICK/EFFECT
button
• For the Left click
34
32
when with the USB connection
(using a USB cable or the optional
remote receiver).
• For changing the pointer or spot
area.
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
38
48
KEYSTONE button
For entering the
Keystone Correction mode.
28
RESIZE button
For switching the
picture size
(NORMAL, BORDER,
etc.).
30
33
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
33
PICTURE MODE
button
For selecting the
appropriate picture.
ECO+QUIET button
32
For lowering the noise
of the cooling fan and
extending the lamp life.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions (Continued)
Inserting the Batteries
Pull down the tab on the cover and remove the cover
towards the direction of the arrow.
1
Insert the batteries.
2
• Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
3
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
•
•
•
•
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
•
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove
them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
•
•
•
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material.
30°
30°
When using the remote control
•
Ensure that you do not drop it or expose it to
moisture or high temperature.
23n (7 m)
•
The remote control may malfunction under a
fluorescent lamp. In this case, move the pro-
jector away from the fluorescent lamp.
Remote control
signal transmitters
Remote control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see
the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
8
6
STANDBY/ON
button
STANDBY button
ON button
8
3
INPUT buttons
ENTER button
4
5
COMPUTER button
6
Adjustment buttons
(P/R/O/Q)
KEYSTONE
button
5
4
4
Zoom ring
ENTER button
4
5
5
Focus ring
Adjustment buttons
(P/R/O/Q)
KEYSTONE button
HEIGHT
ADJUST lever
4
_P. 18
1. Place the projector facing a wall or a screen
2. Connect the projector to the computer and plug the power cord
into the AC socket of the projector
When connecting equipment other than a computer, see
pages 22 and 23.
_PP. 21, 24
3. Remove the lens cap and turn the projector on
On the projector On the remote control
_P. 25
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page 44.)
2 Follow the steps in the Setup Guide and adjust the focus, picture size, and height (angle).
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup
Guide.
_PP. 26, 27
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the projector
Shrinks
Shrinks
lower side.
upper side.
On the remote control
_P. 28
6. Select the INPUT mode
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote control.
On the On the remote
projector
control
On-screen display (RGB)
COMPUTER
INPUT list
INPUT
RGB
COMPUTER
1024 × 768
D
D
DVI-D Computer
DVI-D Video
• When you press INPUT on the projector, the INPUT list appears.
Press '/" to switch the INPUT mode.
_P. 29
7.Turn the computer on
8.Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the
button again while the confirmation message is displayed to put the projector into standby mode.
On-screen display
On the On the remote
projector
control
_P. 25
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image
quality. (See page 28.)
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector,
contact your nearest Sharp Authorized
Projector Dealer or Service Center to obtain
the recommended ceiling-mount adaptor and
unit (sold separately).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode
most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu.
See page 44.)
■ Table mounted, front projection
■ Ceiling mounted, front projection
[Menu item ➞ “Front”]
[Menu item ➞ “Ceiling + Front”]
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■ Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
Example: NORMAL Mode (4:3)
Picture Size
300"
240"
×
180"
200"
160"
×
120"
100"
80"
60"
80"
×
60"
48"
64"
×
36"
48"
×
Projection
Distance
"
"–8'6
"
7'4
(2.2 m – 2.6 m)
"–11'4
–
"
3.5 m)
"–14'2
–
"
9'10
4.3 m)
(3.0 m
"–28'4
–
12'3
(3.7 m
8.6 m)
"
24'7
(7.5 m
36'10
(11.2 m)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Projector (Continued)
Screen Size and Projection Distance
NORMAL Mode (4:3)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
χ
Diag. [ ]
Width
Height
Minimum [L1]
Maximum [L2]
300Љ (762 cm) 610 cm (240Љ) 457 cm (180Љ) 11.2 m (36Ј 10Љ)
—
19 cm (7 9/16Љ)
16 cm (6 19/64Љ)
13 cm (5 3/64Љ)
10 cm (3 25/32Љ)
8 cm (3 1/32Љ)
6 cm (2 33/64Љ)
5 cm (2 1/64Љ)
4 cm (1 49/64Љ)
4 cm (1 33/64Љ)
3 cm (1 1/64Љ)
250Љ (635 cm) 508 cm (200Љ) 381 cm (150Љ) 9.4 m (30Ј 9Љ) 10.8 m (35Ј 5Љ)
200Љ (508 cm) 406 cm (160Љ) 305 cm (120Љ) 7.5 m (24Ј 7Љ)
8.6 m (28Ј 4Љ)
6.5 m (21Ј 3Љ)
5.2 m (17Ј 0Љ)
4.3 m (14Ј 2Љ)
3.5 m (11Ј 4Љ)
3.0 m (9Ј 11Љ)
2.6 m (8Ј 6Љ)
1.7 m (5Ј 8Љ)
150Љ (381 cm) 305 cm (120Љ) 229 cm (90Љ)
5.6 m (18Ј 5Љ)
4.5 m (14Ј 9Љ)
3.7 m (12Ј 3Љ)
3.0 m (9Ј 10Љ)
2.6 m (8Ј 7Љ)
2.2 m (7Ј 4Љ)
1.5 m (4Ј 11Љ)
120Љ (305 cm) 244 cm (96Љ)
100Љ (254 cm) 203 cm (80Љ)
80Љ (203 cm) 163 cm (64Љ)
70Љ (178 cm) 142 cm (56Љ)
60Љ (152 cm) 122 cm (48Љ)
40Љ (102 cm) 81 cm (32Љ)
183 cm (72Љ)
152 cm (60Љ)
122 cm (48Љ)
107 cm (42Љ)
91 cm (36Љ)
61 cm (24Љ)
χ
: Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03745
L2 (m) = 0.04323
[Feet/inches]
L1 (ft) = 0.03745 / 0.3048
L2 (ft) = 0.04323 / 0.3048
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
χ
χ
H (cm) = 0.064
H (in) = 0.064 / 2.54
STRETCH Mode (16:9)
Picture (Screen) size
Width
Projection distance [L]
Distance from the lens center to Adjustable range of
χ
the bottom of the image [H]
69 cm (27 19/64Љ)
55 cm (21 53/64Љ)
image position [S]
ע 52 cm (ע 20 27/64Љ) ע 42 cm (ע 16 11/32Љ) Diag. [ ]
Height
Minimum [L1]
Maximum [L2]
250Љ (635 cm) 553 cm (218Љ) 311 cm (123Љ) 10.2 m (33Ј 6Љ) 11.8 m (38Ј 8Љ)
200Љ (508 cm) 443 cm (174Љ) 249 cm (98Љ)
150Љ (381 cm) 332 cm (131Љ) 187 cm (74Љ)
120Љ (305 cm) 266 cm (105Љ) 149 cm (59Љ)
8.2 m (26Ј 9Љ) 9.4 m (30Ј 11Љ)
6.1 m (20Ј 1Љ) 7.1 m (23Ј 2Љ)
4.9 m (16Ј 1Љ) 5.7 m (18Ј 7Љ)
4.1 m (13Ј 5Љ) 4.7 m (15Ј 5Љ)
3.3 m (10Ј 9Љ) 3.8 m (12Ј 4Љ)
42 cm (16 3
/8Љ)
ע 31 cm (ע 12 1 /4Љ)
33 cm (13 3/32Љ)
28 cm (10 59/64Љ)
22 cm (8 47/64Љ)
17 cm (6 35/64Љ)
11 cm (4 23/64Љ)
ע 25 cm (ע 9 13/16Љ) ע 21 cm (ע 8 11/64Љ) ע 17 cm (ע 6 17/32Љ) ע 12 cm (ע 4 29/32Љ) ע 8 cm (ע 3 17/64Љ) 100Љ (254 cm) 221 cm (87Љ)
80Љ (203 cm) 177 cm (70Љ)
60Љ (152 cm) 133 cm (52Љ)
40Љ (102 cm) 89 cm (35Љ)
125 cm (49Љ)
100 cm (39Љ)
75 cm (29Љ)
50 cm (20Љ)
2.4 m (8Ј 0Љ)
2.8 m (9Ј 3Љ)
1.6 m (5Ј 4Љ)
1.9 m (6Ј 2Љ)
χ
: Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0408
L2 (m) = 0.0471
[Feet/inches]
L1 (ft) = 0.0408 / 0.3048
L2 (ft) = 0.0471 / 0.3048
H (in) = 0.27727 / 2.54
χ
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
χ
H (cm) = 0.27727
χ
χ
S: Adjustable range of image position (cm/in) See page 43.
S (cm) = 0.20754
S (in) = 0.20754 / 2.54
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams above.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC
outlet and turn off the equipment to be connected. After making all connections, turn on the
projector and then the other pieces of equipment.When connecting a computer, ensure that
it is the last equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
•
For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Terminal on
connected equipment
Terminal on the
projector
Equipment
Computer
Cable
RGB cable (supplied)
COMPUTER/
COMPONENT
RGB
output
terminal
mini D-sub 15 pin to DVI cable
(commercially available)
RGB
output
terminal
DVI-I
DVI Digital cable (commercially available)
DVI digital
output
terminal
Note
• See page 63 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-
tor. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-
est Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on (e.g. Press “Fn” and “F5”keys simultaneously
when using a SHARP notebook computer). Refer to the specific instructions in your computer's
operation manual to enable your computer’s external output port.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Projector to Other Equipment (Continued)
Terminal on the
projector
Terminal on
connected equipment
Equipment
Cable
Video equipment
HDMI
output
terminal
HDMI to DVI cable
(commercially available)
DVI-I
DVI Digital cable (commercially available)
DVI digital
output
terminal
Component 3 RCA to mini D-sub 15 pin cable
COMPUTER/
COMPONENT
video
output
terminal
(optional, AN-C3CP2)
S-video
output
S-video cable (commercially available)
Video cable (commercially available)
S-VIDEO
VIDEO
terminal
Video
output
terminal
Camera/Video game
COMPUTER/
COMPONENT
Cables for a camera or a video game/3 RCA
to mini D-sub 15 pin cable (optional,
AN-C3CP2)
Component
video
output
terminal
RCA adaptor plug
(commercially available)
Cables for a camera or a video game
S-VIDEO
VIDEO
S-video
output
terminal
Cables for a camera or a video game
Video
output
terminal
Note
• While the projector is connected to video equipment that has an HDMI output terminal, only the
video signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission
may not work property. (The HDMI specification does not support all connections to video equipment
that has HDMI digital output terminal using HDMI to DVI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by
the video equipment manufacturer.
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal on
connected equipment
Terminal on the
projector
Equipment
Cable
Audio equipment
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
AUDIO 1
ø3.5 mm
audio output
terminal
RCA audio cable (commercially available)
Cables for a camera or a video game
RCA audio
output
terminal
AUDIO 2
Audio
output
terminal
Monitor
RGB cable (supplied or commercially
available)
MONITOR OUT
RGB
input
terminal
Amplifier
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
ø3.5 mm
audio input
terminal
AUDIO OUT
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
RCA audio
input
terminal
Note
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)
• RGB signals and Component signals can be output to the monitor.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-
232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer
can be used to control the projector and check the status of the projector. See page 58 for details.
When connecting to a computer using an RS-232C serial control cable and a DIN-
D-sub RS-232C adaptor
To RS-232C terminal
DIN-D-sub RS-232C
adaptor (supplied)
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• See page 57 for connection of an RS-232C serial control cable.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
Power cord
(supplied)
To AC outlet
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Projector On/Off
Info
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector automatically
turns on when the power cord is plugged into
the AC outlet or the breaker switch is turned
on. (See page 45.)
• English is the factory default language. If you
want to change the on-screen display to an-
other language, change the language accord-
ing to the procedure on page 44.
Turning the Projector on
Note that the connections to external equip-
ment and power outlet should be done be-
fore performing the operations written be-
low. (See pages 21 to 24.)
Remove the lens cap and press
STANDBY/ON on the projector or ON
on the remote control.
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projec-
tor is ready to start operation.
Lamp indicator
Power indicator
Note
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
STANDBY/ON button
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight flicker-
ing of the image may be experienced within the
first minute after the lamp has been illuminated.
This is normal operation as the lamp’s control
circuitry is stabilising the lamp output character-
istics. It should not be regarded as faulty
operation.
• If the projector is put into standby mode and
immediately turned on again, the lamp may take
some time to start projection.
STANDBY
button
•
When System Lock is set, the keycode input box
appears. To cancel the keycode setting, input the
keycode that you have already set. See page 46
for details.
ON button
On-screen display (confirmation message)
Turning the Power off (Putting
the Projector into Standby Mode)
Press STANDBY/ONon the projector or
STANDBY on the remote control, then
press that button again while the confir-
mation message is displayed, to put the
projector into standby mode.
• The projector cannot be turned on while cool-
ing.
Info
• Direct Power Off function:
You can unplug the power cord from the AC out-
let even if the cooling fan is still running.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection
Setup Guide screen
About the Setup Guide
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Press ENTER to exit the Setup Guide
screen.
Note
• The Setup Guide screen automatically high-
lights the items in the following order:
1 FOCUS 2 HEIGHT ADJUST
4 ENTER
3 ZOOM
STANDBY/ON
button
However, you can adjust the focus, height
(angle), or zoom regardless of the highlighted
item.
• If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR - ADJ” -
“Setup Guide” to “Off”. (See page 44.)
ENTER button
Zoom ring
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the fo-
cus while watching the projected image.
2 Adjusting the Picture Size
You can adjust the picture size using
the zoom ring on the projector.
Focus ring
Rotate the zoom ring to enlarge or
shrink the picture size.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
1
HEIGHT
ADJUST lever
Remove your hands from the
HEIGHT ADJUST lever of the pro-
jector after its height has been
finely adjusted.
• The angle of projection is adjustable up
to 9 degrees from the surface on which
the projector is placed.
2
Make small
adjustments.
Use the rear adjustment foot to
3
make the projector level.
• The projector is adjustable 2 degrees
from the standard position.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the pro-
cedures in Keystone Correction to correct the
distortion. (See pages 28 and 43.)
Rear adjustment foot
Info
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
•
Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Correcting Trapezoidal
Distortion
Adjustment buttons
(P/R/O/Q)
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally.The function for
correcting trapezoidal distortion is
called Keystone Correction.
Note
RETURN button
• The Keystone Correction can be adjusted up
to an angle of approximately 40 degrees and
the screen can also be set up to an angle of
approximately 40 degrees (when the resize
mode is set to “NORMAL” (see page 30)).
KEYSTONE button
On-screen display
(Keystone Correction mode)
KEYSTONE
ADJUST
0
Press KEYSTONE to enter the
1
2
END
Keystone Correction mode.
• You can also display the on-screen dis-
play of the Keystone Correction mode
with KEYSTONE on the projector.
Shrinks upper side.
(Move the slide bar in the + direction.)
Press P/Q or O/R to adjust the
Keystone Correction.
• You can also adjust the Keystone Cor-
rection using the adjustment buttons on
the projector.
Shrinks lower side.
(Move the slide bar in the - direction.)
Note
• To return to the default setting, press RETURN
while the on-screen display of the Keystone
Correction mode is on the screen.
Press KEYSTONE.
3
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use KEYSTONE on the pro-
jector.
Info
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER, DVI,
S-VIDEO, VIDEO
buttons
Switching the Input Mode
Select the appropriate input mode for
the connected equipment.
AV MUTE button
Press COMPUTER, DVI, S-VIDEO or
VIDEO on the remote control to select
VOL +/– (Volume)
buttons
the input mode.
• When you press INPUT on the projector or DVI
on the remote control, the INPUT list appears.
Press P/R to switch the INPUT mode.
Adjusting the Volume
Press VOL +/– on the remote control or
–O/Q+ on the projector to adjust the vol-
ume.
Note
• Pressing VOL–/–O will lower the volume.
• Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the external equip-
ment changes in accordance with the volume
level of the projector. Set the projector’s volume
to the lowest level when turning the projector on/
off or when changing the input signal.
On-screen display
• When you do not want to output the sound from
the projector’s speaker while the projector is con-
nected to external equipment, set “Speaker” in
“PRJ-ADJ” menu to “Off”. (See page 45.)
Displaying the Black Screen
and Turning off the Sound
Temporarily
Press AV MUTE on the remote control
to temporarily display a black screen
and turn off the sound.
On-screen display
Note
• Pressing AV MUTE again will turn the pro-
jected image back on.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose a desired image.
Press RESIZE.
• See page 43 for setting on menu screen.
RESIZE
button
COMPUTER
Main resolution
SVGA (800 × 600)
XGA (1024 × 768)
SXGA (1152 × 864)
SXGA+ (1400 × 1050)
SXGA (1280 × 1024)
1280 × 720
NORMAL
FULL
DOT BY DOT
800 × 600
—
BORDER
STRETCH
—
4:3 aspect ratio
1024 × 768
1152 × 864
1400 × 1050
1280 × 1024
1280 × 720
1360 × 768
1366 × 768
1280 × 768
1280 × 800
768 × 576
1024 × 576
968 × 768
1024 × 576
1024 × 578
1024 × 576
1024 × 614
1024 × 640
—
—
—
—
—
1360 × 768
1024 × 768
Other aspect ratios
1366 × 768
—
1280 × 768
960 × 576
922 × 576
1024 × 576
1280 × 800
For 4:3 screen
FULL
For 16:9 screen
Input signal
Computer
Image type
NORMAL
DOT BY DOT
BORDER
STRETCH
Resolution
lower than
XGA
1
1
2
2
*
*
XGA
*
*
4:3 aspect ratio
Resolution
higher than
XGA
SXGA (1280 1024)
5:4 aspect ratio
16:9 aspect ratio
1
*
1280 720
2
2
*
*
1360 768
1366 768
1280 768
1
1
1
*
*
*
1280 800
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
The Image Shift function can be used for these images.
Same as NORMAL mode.
1
2
*
*
30
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO/DTV
Input signal
For 4:3 screen
AREA ZOOM
For 16:9 screen
BORDER STRETCH
Video/DTV
Image type
NORMAL
V-STRETCH
1
1
1
*
*
*
*
*
*
4:3 aspect ratio
1
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Squeeze
1
1
Letter box
720P, 1035I,
1080I, 1080P
1
*
16:9 aspect ratio
2
*
2
*
16:9 aspect ratio
540P
1
*
(4:3 aspect ratio in 16:9)
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
The Image Shift function can be used for these images.
Same as NORMAL mode.
1
2
*
*
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to
a TV program or video image, the image will look different from its original appearance.
Keep this in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image
for commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the Remote Control
BREAK TIMER button
FREEZE button
Displaying the Pointer
MAGNIFY buttons
Press POINTER and press P/R/
1
O/Qon the remote control to move
POINTER button
SPOT button
the pointer.
• Press EFFECT to change the pointer icon
(5 types).
Press POINTER again.
• The pointer will disappear.
Adjustment buttons
2
(P/R/O/Q)
EFFECT button
PICTURE MODE button
ECO+QUIET button
AUTO SYNC button
Using the Spot Function
Press SPOT and press P/R/O/Q
1
on the remote control to move the
Displaying and Setting the
Break Timer
spot area.
• Press EFFECT to change the spot area
size (3 types).
Press BREAK TIMER.
• The timer starts to count down from 5
minutes.
Press SPOT again.
• The spot area will disappear.
1
2
On-screen display
Press P /R /O /Q to adjust the
Switching the Eco+Quiet
Mode
2
length of the break time.
• Increases with P or Q
5 minutes s 6 minutes s 60 minutes
• Shortens with O or R
4 minutes s 3 minutes s1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
• When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the
power consumption will decrease, and the lamp
life will extend.
Canceling the break timer display function
Press BREAK TIMER.
Note
• Refer to “Lamp Setting” on page 42 for de-
tails of the Eco+Quiet mode.
Note
• Break Timer does not function while the pro-
jector is operating the “Auto Sync”, “FREEZE”
or “AV MUTE” functions.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Sync
(Auto Sync Adjustment)
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of
projected images can be enlarged.This
is helpful when providing more detailed
explanations.
Auto Sync function works when detect-
ing input signal after the projector turns
on.
Press AUTO SYNC to manually adjust
with Auto Sync function.
Press
MAGNIFY on the remote
1
control.
Note
• Enlarges the image.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 48.)
• Pressing
or
MAGNIFY enlarges
or reduces the projected image.
Note
Press
2
.
.
1
3
4
Freezing a Moving Image
Press
• You can change the location of the en-
larged image using P, R, O and Q.
Press FREEZE.
• The projected image is frozen.
1
Press FREEZE again to return to
Press RETURN on the remote con-
trol to cancel the operation.
• The magnification then returns to ×1.
2
2
the moving image from the cur-
rently connected device.
Note
• The selectable magnifications differ
depending on the input signal.
• In the following cases, the image will
return to the normal size (×1).
Selecting the Picture Mode
- When switching the INPUT mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
- When the Resize mode is changed.
- When the Picture mode is changed.
- When the Progressive mode is changed.
You can select the appropriate picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
• When pressing PICTURE MODE, the picture
mode changes in the following order:
*
STANDARD PRESENTATION
MOVIE GAME sRGB
Note
• See page 40 for details on the picture mode.
* “sRGB” is displayed only when RGB signal is
input.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating with the Remote Control (Continued)
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use
the remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the
USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate
the projector with the remote control. For details, see the operation manual of
the receiver.
Connecting with a USB cable
Computer
R
emote receiver
To USB terminal
(optional, AN-MR2)
To USB terminal
or
USB cable
(commercially available or available as
Sharp service part QCNWGA014WJPZ)
PAGE UP/
PAGE DOWN buttons
The mouse pointer can be oper-
ated in the following way after it
is connected.
MOUSE/Adjustment
buttons ('/"/\/|)
■ When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
■ When left-clicking
Press L-CLICK.
■ When right-clicking
R-CLICK button
L-CLICK button
Press R-CLICK.
■
When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
■ When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard.
Press PAGE UP or PAGE DOWN.
Note
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function
does not work with the following operation systems that do not support USB.
• Versions earlier than Windows® 95
• Versions earlier than Windows® NT4.0
• Versions earlier than Mac OS® 8.5
• You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items
The following shows the items that can be set in the projector.
Main menu
Sub menu
“Picture” menu
Standard
Presentation
Movie
Picture
Picture Mode
Page 40
Page 40
PAGE 1
Game
sRGB*1
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
Picture Mode
Contrast
Bright
Color
0
0
0
0
0
Contrast
Bright
Color
Tint
-30
-30
-30
-30
-30
-30
-30
+30
+30
+30 *2
Tint
Sharp
Red
*2
+30
0
0
Sharp
Red
+30 *2
+30
Blue
Blue
+30
Page 41
SEL./ADJ.
ENTER
END
PAGE 2
CLR Temp
-1
0
1
2
Picture
SCR - ADJ
PRJ - ADJ
Help
Page 41
BrilliantColor™
Picture Mode
Standard
0
1
Page 41
C.M.S. Setting [On/Off]
CLR Temp
BrilliantColorTM
C.M.S. Setting
C.M.S.
Progressive
DNR
On
Page 41
3D Progressive
C.M.S.
Off
Page 41
Progressive
Lamp Setting
Reset
Bright
2D Progressive
3D Progressive
Film Mode
*2
Page 42
DNR
Off
Level 1
Level 2
SEL./ADJ.
ENTER
END
Page 42
Lamp Setting
Bright
Eco + Quiet
Page 42
Reset
“C.M.S.”
C. M. S.
C. M. S. - Hue
C. M. S. - Saturation
C. M. S. - Value
Reset
C.M.S.-Hue
R
Y
-30
-30
-30
-30
-30
-30
+30
+30
+30
+30
+30
+30
Page 41
C.M.S.-Saturation
G
R
0
0
0
0
0
0
C
Page 41
C.M.S.-Value
Y
G
B
C
M
Page 41
Reset
B
Reset
M
Reset
SEL./ADJ.
Return
ENTER
END
*1 Items when inputting RGB signal through
COMPUTER or DVI.
*2 Items when inputting component signal through
COMPUTER or DVI, or when selecting S-VIDEO or
VIDEO.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Items (Continued)
“Screen adjustment (SCR-ADJ)” menu
Main menu
SCR - ADJ
Sub menu
Picture
Resize
SCR - ADJ
PRJ - ADJ
Border
Help
Resize
Normal
Normal
Full
Area Zoom
V-Stretch
Border
Page 43
Image Shift -96 +96
Page 43
Image Shift
Keystone
0
0
Dot By Dot
Area Zoom
V-Stretch
Border
Stretch
Page 43
Keystone
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
On
VIDEO/
S-VIDEO
Stretch
-80 +80
Off
COMPUTER/
DTV
Logo
On
Page 43
OSD Display [On/Off]
Front
English
Page 43
Closed Caption
Page 44
Language
Off
CC1
CC2
SEL./ADJ.
ENTER
END
Background
Logo
Blue
None
Page 44
Setup Guide [On/Off]
Page 44
PRJ Mode
Front
Ceiling + Front
Rear
Ceiling + Rear
Page 44
English
Language
Deutsch
Español
Nederlands
Français
Italiano
Page 44
Svenska
Português
polski
Magyar
Türkçe
“Projector adjustment (PRJ-ADJ)” menu
Main menu
PRJ - ADJ
Sub menu
Picture
SCR - ADJ
PRJ - ADJ
Help
Auto Sync [On/Off]
Auto Sync
On
On
On
Page 45
Page 45
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Speaker
Auto Power Off [On/Off]
Standard
Page 45
Auto Restart [On/Off]
On
On
Audio Input
RS-232C
Audio 1
9600bps
Normal
Disable
Page 45
STANDBY Mode
Standard
Eco
Fan Mode
Page 45
System Sound [On/Off]
System Lock
Lamp Timer(Life)
0
h
0
min 100%
Page 45
Speaker [On/Off]
SEL./ADJ.
ENTER
END
Page 45
Audio Input
Audio 1
Audio 2
Page 46
RS-232C
9600bps
115200bps
Page 46
Fan Mode
Normal
High
Page 46
System Lock
[Enable/Disable]
Page 46
Lamp Timer(Life)
Page 47
36
Download from Www.Somanuals.com. All Manuals Search And Download.
“Help” menu
The items you can set with the “Help”
menu
Picture
SCR - ADJ
PRJ - ADJ
Help
“Help” menu n Page 48
• Vertical stripes or flickering image appear
Auto Sync
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Clock
Phase
Picture is dark
• Data image is not centered
Auto Sync
The image is distorted
Reset all adjustments to default settings
H-Pos
V-Pos
• Color is faded or poor
COMPUTER/COMPONENT or DVI input
Signal type: Auto/RGB/Component
S-VIDEO or VIDEO input
Video System: Auto/PAL/SECAM/
NTSC3.58/NTSC4.43/
SEL.
ENTER
END
PAL-M/PAL-N/PAL-60
DVI (Digital) input
Dynamic range: Auto/Standard/Enhanced
* The selectable items vary depending on the in-
put signal and the selected input mode.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU/HELP button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU/HELP button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Example: “Picture” screen menu for
Press MENU/HELP.
1
2
COMPUTER (RGB) input
• The “Picture” menu screen for the se-
lected input mode is displayed.
Menu item
Press Q or O and select“Picture”
to adjust.
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
Picture Mode
Contrast
Bright
0
0
0
0
0
1
Red
Blue
CLR Temp
BrilliantColorTM
On
C.M.S. Setting
C.M.S.
DNR
Off
Lamp Setting
Reset
Bright
SEL./ADJ.
ENTER
END
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Press P or R and select “Bright”
to adjust.
• The selected item is highlighted.
3
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
Picture Mode
Contrast
Bright
0
0
0
0
0
1
Red
Blue
CLR Temp
BrilliantColorTM
On
C.M.S. Setting
C.M.S.
DNR
Off
Lamp Setting
Reset
Bright
SEL./ADJ.
Single ADJ
END
Help
Items to be adjusted
Picture
Resize
SCR - ADJ
PRJ - ADJ
Border
Image Shift
Keystone
0
0
To adjust the projected
image while watching it
Press ENTER.
Press ENTER.
• The selected item (e.g. “Bright”) is dis-
played by itself at the bottom of the
screen.
• When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.
The item displayed by itself
Picture
Bright
0
SEL./ADJ.
Rtn. Menu
END
Note
• Press ENTER again to return to the pre-
vious screen.
Press O or Q to adjust the item
selected.
4
5
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
Picture Mode
Contrast
Bright
• The adjustment is stored.
0
1 5
0
Red
Blue
CLR Temp
BrilliantColorTM
0
0
1
On
C.M.S. Setting
C.M.S.
DNR
Lamp Setting
Reset
Off
Bright
Press MENU/HELP.
• The menu screen will disappear.
SEL./ADJ.
Single ADJ
END
Note
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”,
“FREEZE”, or “AV MUTE” functions.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
Menu operation n Page 38
Q PAGE1
Q PAGE2
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
Picture
SCR - ADJ
PRJ - ADJ
Standard
Help
1
2
Picture Mode
Contrast
Bright
Color
Picture Mode
0
0
0
0
0
0
1
CLR Temp
BrilliantColorTM
3
2
4
5
6
7
Tint
C.M.S. Setting
C.M.S.
Progressive
DNR
On
Sharp
Red
0
0
3D Progressive
Off
Blue
Lamp Setting
Reset
Bright
SEL./ADJ.
ENTER
END
SEL./ADJ.
ENTER
END
1 Selecting the Picture Mode
The default settings of each item when selecting Picture Mode
Selectable
items
Description
CLR Temp
BrilliantColorTM
Lamp Setting
Standard
For standard image
1
2
Bright
Bright
0
0
Presentation Brightens portions of image for
more enhanced presentations.
Movie
Game
*sRGB
Gives natural tint to the
projected image.
0
1
–
Eco + Quiet
Bright
–1
0
Gives sharpness to the
projected image.
For high fidelity reproduction of
images from a computer.
Bright
–
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
Note
•
You can also press PICTURE MODE on the remote control to select the picture mode. (See page 33.)
• *sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
For additional information about the sRGB function, visit “http://www.srgb.com/”.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColorTM”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu operation n Page 38
2 Adjusting the Image
4 Adjusting the Colors
This function adjusts each of the six main colors
that comprise the color wheel, altering their
“Hue”, “Saturation”, or “Value”.
Adjustment
items
O button
Q button
Contrast
For less
contrast.
For more
contrast.
Selectable items
Description
Bright
Color*1
Tint*1
For less
brightness.
For less color
intensity.
For making skin For making skin
tones purplish. tones greenish.
For more
brightness.
For more color
intensity.
C.M.S.-Hue
Sets the hue of the main colors.
C.M.S.-Saturation Sets the saturation of the main
colors
C.M.S.-Value
Sets the brightness of the main
colors.
Sharp*1
For less
For more
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
sharpness.
sharpness.
Red*2
Blue*2
For weaker red. For stronger red.
For weaker blue. For stronger blue.
BrilliantColor™*2 *3 For making the For making the
Adjusting “Hue”, “Saturation”, or “Value”.
effect weaker.
effect stronger.
1Select “On” for “C.M.S. Setting” in the “Picture”
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments’
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
2mSeelneucta“nCd.Mth.Se.n” pinrethsse E“PNicTtEuRre.” menu and then
3Pprreessss EPNoTrERR.to select either “Hue”, “Saturation”, or
4“SVealelucet”thaendcothloerntopbreessadEjNusTtEedR.with P or R and
adjust it with O or Q.
Note
Example of adjusting the “Hue”
• “Red”, “Blue”, “BrilliantColorTM” and “CLR
Temp” cannot be set when “sRGB” is selected.
• To reset all adjustment items, select “Reset”
and press ENTER.
Main colors
R (Red)
O button
Q button
Closer to magenta Closer to yellow
Y (Yellow)
G (Green)
C (Cyan)
B (Blue)
Closer to red
Closer to green
Closer to cyan
Closer to blue
Closer to magenta
Closer to red
Closer to yellow
Closer to green
Closer to cyan
3 Adjusting the Color
Temperature
M (Magenta) Closer to blue
• When “Saturation” is selected, the selected
color becomes
Selectable
Description
items
O: lighter. Q: thicker.
For lower color temperature for
• When “Value” is selected, the selected color
becomes
O: darker. Q: brighter.
–1
0
warmer, reddish incandescent-like
images.
P
R
For higher color temperature for
• To reset the adjustment values of each color
to the default settings, select “Reset” and press
ENTER.
1
cooler, bluish, fluorescent-like images.
Note
• Values on “CLR Temp” are only for general
standard purposes.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 38
5 Progressive
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high
quality images with minimal dot crawl and cross
color noise.
Selectable
items
Description
2D Useful to display fast-moving images
Progressive such as sports.
Selectable
Description
items
3D
Useful to display relatively slow-
Progressive moving images such as drama and
documentary more clearly.
Off
The DNR function is not activated.
Level 1
Level 2
Sets the DNR level for viewing a
clearer picture.
Film Mode Reproduces the image of film source*
clearly. Displays the optimized image of
film transformed with three-two pull down
(NTSC and PAL60Hz) or two-two pull
down (PAL50Hz and SECAM) enhance-
ment to progressive mode images.
Note
Set “DNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving
images drag.
• When TV broadcasts with weak signals are
projected.
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The
projector can convert this film source to progres-
sive video at 60 frames/second with NTSC and
PAL60Hz or at 50 frames/second with PAL50Hz
and SECAM to play back a high-definition image.
Note
7 Lamp Setting
• In NTSC or PAL60Hz, even if the 3D Progres-
sive mode has been set, the three-two pull
down enhancement will be enabled automati-
cally when the film source has been entered.
• When the image is blurred or noisy, switch to
the optimal mode.
Selectable
items
Brightness and Power consumption
Eco + Quiet PG-F312X
PG-F262X
Approx. 60%
Approx. 70%
Approx. 80%
PG-F212X
Bright
100%
Info
• This function is available for 480I and 576I
signals using COMPUTER/COMPONENT or
DVI input.
• This function is available for all signals with
S-VIDEO and VIDEO input.
Note
• In the Eco + Quiet mode, the fan sound and
power consumption are lower than those in
the Bright mode. (Projection brightness de-
creases as shown in the chart.)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image
(“SCR - ADJ” Menu)
Menu operation n Page 38
Picture
Resize
SCR - ADJ
PRJ - ADJ
Border
Help
1
2
3
Image Shift
Keystone
0
0
4
5
6
7
8
9
OSD Display
Closed Caption
Background
Setup Guide
PRJ Mode
On
Off
Logo
On
Front
English
Language
SEL./ADJ.
ENTER
END
3 Keystone Correction
1 Setting the Resize Mode
When the image is projected either from the top
or from the bottom towards the screen at an angle,
the image becomes distorted trapezoidally. The
function for correcting trapezoidal distortion is
called Keystone Correction.
Note
• For details of the Resize mode, see pages
30 and 31.
• You can also press RESIZE on the remote con-
trol to set the resize mode. (See page 30.)
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
See page 28 for details of Keystone Correction.
2 Adjusting the Image
Q button
O button
Position
You can move the projected image vertically.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately 40 degrees
(when “Resize” is set to “Normal”).
• You can also press KEYSTONE on the remote
control or on the projector to adjust Keystone
Correction.
O button
Q button
4 Setting the On-screen
Display
Selectable
Description
items
Note
• This function only works in some RESIZE
modes. (See pages 30 and 31.)
On
Off
All on-screen displays are displayed.
INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/ “An invalid
button has been pressed.” are not
displayed.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projected Image
(“SCR - ADJ” Menu) (Continued)
Menu operation n Page 38
5 Closed Caption
• “Closed Caption” is a system which allows
conversations, narration, and sound effects in
TV programs and home videos to be viewed
as captions on the screen.
• Not all programs and videos will offer closed
captioning. Please look for the
ensure that captions will be shown.
• Two channels are available: CH1 and CH2.
“Closed Caption” shows subscripts of dialogs
and commentaries of TV dramas and news
programs while allowing a clear view of the
picture.
8 Reversing/Inverting
Projected Images
Selectable items
Front
Description
Normal image (Projected from
the front of the screen)
symbol to
Ceiling + Front
Rear
Inverted image (Projected
from the front of the screen
with an inverted projector)
Reversed image (Projected
from the rear of the screen or
with a mirror)
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
Selectable items
Description
Off
—
See page 19 for details of Projection (PRJ) Mode.
CC1
CC2
Closed Caption mode for CH1 data
Closed Caption mode for CH2 data
9
Selecting the On-screen
Display Language
Note
• This function enables the display of captions
(text content) which are standardized by the
Federal Communications Commission, an
independent US government agency.
• Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
The projector can switch the on-screen display
language among 17 languages.
English
Deutsch
Español
Nederlands
Français
Italiano
•
If any button is pressed to call up the on-screen
display while viewing a Closed Caption broadcast,
the closed captions will disappear momentarily.
Svenska
Português
polski
Magyar
6
Selecting the Background
Image
Türkçe
Selectable items
Logo
Blue
Description
Sharp logo screen
Blue screen
None
—
7
Selecting the Setup Guide
Selectable items
Description
On
Displaying the Setup Guide
when turning the projector on.
Off
Not displaying the Setup Guide.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ - ADJ” Menu)
Menu operation n Page 38
Picture
SCR - ADJ
PRJ - ADJ
Help
3 Auto Restart Function
Selectable
Description
items
1
2
3
4
5
6
7
8
9
0
Auto Sync
On
On
On
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Speaker
Standard
On
On
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
On
Audio Input
RS-232C
Audio 1
9600bps
Normal
Disable
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
Fan Mode
System Lock
Lamp Timer(Life)
0
h
0
min 100%
Off
The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
SEL./ADJ.
ENTER
END
1
Auto Sync (Auto Sync
Adjustment)
4 STANDBY Mode
When set to “Eco”, power consumption is
reduced in standby mode.
Selectable
items
Description
On
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Selectable
Description
items
Eco
The monitor output and RS-232C
functions are switched off in standby
mode.
Off
Auto Sync adjustment is not
automatically performed.
Standard
The monitor output and RS-232C
functions are activated even if the
projector is in standby mode.
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC on the remote control.
• The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
5
Setting the Confirmation
Sound (System Sound)
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 48.)
Selectable
items
Description
On
A confirmation sound is made when
the projector turns on/off.
2
Auto Power Off Function
Off
No confirmation sound is made.
Selectable
items
Description
6 Speaker Setting
Selectable
Description
items
On
Off
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
The Auto Power Off function will be
disabled.
On
The audio signal is output from the
internal speaker.
Off
The audio signal is not output from the
internal speaker.
Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector Function (“PRJ - ADJ” Menu)
(Continued)
Menu operation n Page 38
a Setting/Changing the keycode
7 Audio Input
Select “System Lock”, then press
ENTER or Q.
This function allows you to select an appropriate
combination of audio input terminals for each
input mode.
1
2
Selectable
Description
items
Select “Next”, then press ENTER.
• The screen for entering the keycode
appears.
Audio 1
The AUDIO 1 input terminal is used as
an audio input terminal.
Audio 2
The AUDIO 2 input terminal is used as
an audio input terminal.
Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
3
8
Selecting the Transmission
Speed (RS-232C)
•
When setting the keycode for the first time,
press R on the projector for four times.
PRJ - ADJ
Make sure that both the projector and computer
are set for the same baud rate.
Setting the System Lock
– – – –
– – – –
– – – –
Old Code
New Code
Reconfirm
Selectable
Description
items
9600bps
Transmission speed is slow.
P
Note
R
115200bps Transmission speed is rapid.
• If you input a wrong keycode, the cursor
returns to the first point of the “Old Code”.
• The preset keycode is 4 R buttons on
the projector. When you press the R but-
ton four times, the keycord input screen
disappears.
9 Fan Mode Setting
This function changes the fan rotation speed.
Selectable
Description
items
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
4
Normal
High
Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 1,500
meters (4,900 feet) or more.
Note
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
• You cannot use the following buttons for
keycode: STANDBY/ON, ON, STANDBY,
ENTER
and MENU/HELP
,
L-CLICK, R-CLICK/RETURN
0 System Lock Function
•
System lock function recognizes each
button on the remote control or on the
projector as an individual button, even if
they share the same button name. If you
used the buttons on the projector in
setting your keycode, the keycode cannot
be canceled with the remote control.
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only au-
thorized users have access.
Info
PRJ - ADJ
Setting the System Lock
•
If you lose or forget your keycode, contact
your nearest Sharp Authorized Projector
Dealer or Service Center (see page 66). Even
if the product warranty is valid, the keycode
reset will incur a charge.
Old Code
* * * *
– – – –
– – – –
New Code
Reconfirm
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter the same keycode in “Re-
confirm”.
Keylock Function
5
Locking the Operation
Buttons on the Projector
Use this function to lock the operation buttons
on the projector.
Note
To cancel the keycode that you have already
set
• Press R on the projector for four times in steps
4 and 5 above.
When the System Lock is set
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
a Locking the Operation Buttons
Hold down ENTER on the projector for about 5
seconds while the projector is being turned on.
On-screen display
Input screen for keycode
• The keylock function does not affect the opera-
tion with the remote control buttons.
• You cannot use the keylock function while the
projector is warming up.
– – – –
System Lock
a Taking the Keylock off
Hold down ENTER on the projector for about 5
seconds.
Checking the Lamp Life
Status
On-screen display
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Lamp usage condition
Remaining lamp life
• When the projector is in standby mode, you can
release the keylock by holding down ENTER
and STANDBY/ON on the projector simulta-
neously for about 5 seconds.
“Life”
100%
5%
Operated exclusively
with Lamp Setting set to X,XXX
“Eco +Quiet”
Approx.
Approx.
XXX hours
hours
Info
Operated exclusively
Approx.
Approx.
with Lamp Setting set to X,XXX
“Bright”
hours
XXX hours
• Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in standby mode, warming up, chang-
ing input signals, operating “Auto Sync”
function, in “FREEZE” mode or on the “System
Lock” screen during warming up.
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the us-
age condition.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting with the “Help” Menu
This function advises you to solve the problems during usage.
Utilizing the “Help” Menu
Functions
ENTER button
Adjustment buttons
(P/R/O/Q)
Example: When image flickering appears
Operation to solve image flickering when pro-
jecting the computer RGB signal.
MENU/HELP
button
Press MENU/HELP.
1
Press O or Q to select“Help”, then
2
Select “Initiate “Auto Sync” Ad-
4
5
press ENTER.
justments”, then press ENTER.
If the image is not improved, se-
lect “Adjust horizontal noise”,
then press ENTER.
Press P or R to select “Vertical
3
stripes or flickering image ap-
pears” on Help menu, then press
ENTER.
Press O or Q to adjust.
6
Picture
SCR - ADJ
PRJ - ADJ
Help
Help
Vertical stripes or flickering image appear
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Phase
SEL./ADJ.
0
Rtn. Menu
END
Picture is dark
Note
The image is distorted
• You can adjust the items with check marks (✔).
• The items in the “Help” menu change, de-
pending on the input signal or setting that you
have selected.
Reset all adjustments to default settings
• If the problem is not solved, refer to
“Troubleshooting” (see pages 64 and 65).
• When selecting “sRGB” in “Picture Mode”, the
item “Color is faded or poor” is not displayed.
This means you cannot change input signal
types.
SEL.
ENTER
END
Press ENTER.
Help
Vertical stripes or flickering image appear
Initiate “Auto Sync” Adjustments.
If there is no change after performing "Auto Sync"
adjustments, adjust the following items.
Adjust vertical noise
Adjust horizontal noise
Reset the 2 items above
Return
Signal Info
1024ꢀ ꢀ ꢀ ꢀ 768
59.9 Hz
H
48.3 kHz
/
V
SEL.
ENTER
END
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning the projector
Cleaning the lens
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on the
cabinet.
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.
■ As the surface of the lens can easily get
damaged, be careful not to scrape or hit the
lens.
■ Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector. Make
sure to test on a small, inconspicuous area on
the projector before use.
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Info
• If you want to clean the air vents during projec-
tor operation, ensure you press STANDBY/ON
on the projector or STANDBY on the remote
control and put the projector into standby
mode. After the cooling fan has stopped, clean
the vents.
Thinner
Wax
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter standby mode. After the projector has entered standby mode,
follow the procedures given below.
Top View
Temperature warning
indicator
Lamp indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-
tor will enter standby mode. After “
” appears, ensure you perform the measures described on
page 51.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
Indicators on the Projector
Power indicator
Red on
Normal (Standby)
Green on
Red blinks
Normal (Power on)
Abnormal (See page 51.)
Green blinks Normal (Cooling)
Green on Normal
Green blinks The lamp is warming up.
Lamp indicator
Red on
The lamp is shut down abnormally or requires to be
changed. (See page 51.)
Temperature warning Off
indicator
Normal
Red on
The internal temperature is abnormally high. (See page 51.)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance indicator
Problem
Cause
Possible Solution
Normal
Abnormal
Tempera-
ture
warning
indicator
The internal
temperature is
abnormally
high.
•
Blocked air intake
• Relocate the projector to
an area with proper
ventilation. (See page 8.)
Off
Red on
(Standby)
•
•
Cooling fan
breakdown
Internal circuit
failure
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 66) for
repair.
•
•
Clogged air intake
Lamp
indicator
The lamp does
not illuminate.
The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Green on
(Green
blinks
Red on
when the
lamp is
warming
up or
turning
off.)
Time to change
the lamp.
•
Remaining lamp life • Carefully replace the lamp.
becomes 5% or
less.
(See page 52.)
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 66) for
repair.
The lamp does
not illuminate.
•
•
Burnt-out lamp
Red on
(Standby)
Lamp circuit failure
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Power
indicator
The power
•
The lamp unit cover • If the power indicator blinks
Green on/
Red on
Red
blinks
indicator blinks
in red when the
projector is on.
is open.
in red even when the lamp
unit cover are securely
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 66) for
advice.
Green
blinks
(Cooling)
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plug-
ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-
nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is con-
trolled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (See page 47.)
■ Purchase a replacement lamp of type AN-F212LP from your place of purchase, nearest Sharp
Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
U.S.A. ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case
of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
cool before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. * If you wish,
you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service
Center.
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing and Installing
the Lamp Unit
Warning!
• Do not remove the lamp unit from the projec-
tor right after use. The lamp and parts around
the lamp will be very hot and may cause burns
or injury.
Lamp unit
AN-F212LP
Optional
accessory
STANDBY/ON button
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
AC socket
Press STANDBY/ON on the projec-
1
tor or STANDBY on the remote
control to put the projector into
standby mode.
User service screw
(for lamp unit cover)
• Wait until the cooling fan stops.
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
2
1
• Leave the lamp until it has fully cooled
down (about 1 hour).
2
Remove the lamp unit cover.
3
• Turn the projector over. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Regarding the Lamp (Continued)
Remove the lamp unit.
4
• Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Insert the new lamp unit.
5
• Press the lamp unit firmly into the lamp
Securing screws
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.
• Align the tab on the lamp unit cover
(1) and place it while pressing the tab
(2) to close it. Then tighten the user ser-
vice screw (3) to secure the lamp unit
cover.
6
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
AC socket
Connect the power cord.
• Plug the power cord into the AC socket
of the projector.
1
STANDBY/ON
button
Reset the lamp timer.
2
ENTER button
• While simultaneously holding down
MENU/HELP, ENTER and R on the pro-
jector, press STANDBY/ON on the pro-
jector.
R button
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
MENU/HELP
button
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing the Projector
How to Use the Storage Case
When storing the projector, attach the lens cap
to the lens, and place it in the supplied storage
case.
Open the cover of the storage
case.
1
Place the projector into the stor-
age case.
2
Info
Lens cap
• Ensure the projector has cooled down
sufficiently before placing it in the case.
• When you place the projector into the
storage case, make sure that the
cooling fan has stopped.
• Ensure the lens cap is attached to the
lens for protection.
• Place the projector into the storage
case with the lens facing the handle.
• Ensure the projector is held in place by
using the fixing band.
• Do not expose the storage case to
direct sunlight or near heat sources. The
storage case may change color or
become deformed.
Fixing band
Close the cover of the storage
case.
3
Place the accessories in the front
pocket of the storage case.
4
Supplied accessories
(Rremote control, etc.)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Pin Assignments
COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals : mini D-
sub 15 pin female connector
COMPUTER Input/Output
Pin No. Signal
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
COMPONENT Input/Output
Pin No. Signal
1. PR (CR)
11
15
2.
Y
3. PB (CB)
4. Not connected
5. Not connected
6. Earth (PR)
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
7. Earth (Y)
8. Earth (PB)
9. Not connected
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
10. GND
1
6
5
10
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
DVI-I Terminal : 29 pin connector
• DVI Digital Input
Pin No. Signal
1. T.M.D.S data 2–
23
24
18
17
Pin No.
Signal
16. Hot plug detection
17. T.M.D.S data 0–
18. T.M.D.S data 0+
19. T.M.D.S data 0 shield
20. Not connected
21. Not connected
22. T.M.D.S clock shield
23. T.M.D.S clock+
24. T.M.D.S clock–
C1. Not connected
C2. Not connected
C3. Not connected
C4. Not connected
C5. Ground
2. T.M.D.S data 2+
3. T.M.D.S data 2 shield
4. Not connected
5. Not connected
6. DDC clock
C3
C5
C4
7. DDC data
C2
8. Not connected
9. T.M.D.S data 1–
10. T.M.D.S data 1+
11. T.M.D.S data 1 shield
12. Not connected
13. Not connected
14. +5V power
C1
8 7
16
2 1
9
15. Ground
• DVI Analog RGB Input
Pin No. Signal
• DVI Analog Component Input
Pin No. Signal Pin No.
Pin No.
Signal
Signal
1. Not connected
2. Not connected
3. Not connected
4. Not connected
5. Not connected
6. DDC clock
16. Hot plug detection
17. Not connected
18. Not connected
19. Not connected
20. Not connected
21. Not connected
22. Not connected
23. Not connected
24. Not connected
C1. Analog input Red
C2. Analog input Green
(Sync On Green)
1. Not connected
2. Not connected
3. Not connected
4. Not connected
5. Not connected
6. Not connected
7. Not connected
8. Not connected
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Ground
16. Not connected
17. Not connected
18. Not connected
19. Not connected
20. Not connected
21. Not connected
22. Not connected
23. Not connected
24. Not connected
C1. Analog input Pr/Cr
C2. Analog input Y
C3. Analog input Pb/Cb
C4. Not connected
C5. Ground
7. DDC data
8. Vertical sync
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
C3. Analog input Blue
C4. Horizontal sync
(Composite Sync)
14. +5V power
15. Ground
C5. Ground
56
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Terminal : mini DIN 9 pin female connector
8
Pin No. Signal
Name
I/O
Reference
1.
Not connected
9
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
Receive Data
Send Data
Input
Output
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
7
SG
Signal Ground
6
3
RS
CS
Request to Send
Clear to Send
4
5
2
1
RS-232C Terminal : D-sub 9 pin male connector of the DIN-D-sub RS-232C adaptor
1
5
Pin No. Signal
Name
I/O
Reference
Not connected
Connected to internal circuit
Connected to internal circuit
Not connected
Connected to internal circuit
Not connected
Connected to CS in internal circuit
Connected to RS in internal circuit
Not connected
1.
2.
3.
4.
5.
6.
7.
8.
9.
RD
SD
Receive Data
Send Data
Input
Output
SG
Signal Ground
RS
CS
Request to Send
Clear to Send
6
9
RS-232C Cable recommended connection : D-sub 9 pin female connector
Pin No. Signal
Pin No.
Signal
5
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
1.
2.
3.
4.
5.
6.
7.
8.
9.
CD
RD
SD
ER
SG
DR
RS
CS
CI
9
6
Note
•Depending on the controlling device used, it may be necessary to connect Pin 4 and Pin 6 on the
controlling device (e.g. computer).
Projector
Pin No.
Computer
Pin No.
4
5
6
4
5
6
USB Terminal : Type B USB connector
4
3
Pin No. Signal
Name
1.
2.
3.
4.
VCC
USB–
USB+
SG
USB power
USB data–
USB data+
Signal Ground
1
2
57
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands
Computer control
A computer can be used to control the projector by connecting an RS-232C serial control
cable (cross type, commercially available) to the projector. (See page 24 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate*: 9,600 bps / 115,200 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
*Set the projector’s baud rate to the same rate as used by the computer.
Basic format
Commands from the computer are sent in the following order: command, parameter, and
return code. After the projector processes the command from the computer, it sends a re-
sponse code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Return code (0DH
)
Command 4-digit
Parameter 4-digit
Response code format
Normal response
Problem response (communication error or incorrect command)
Return code (0DH
)
O
K
Return code (0DH
)
E
R
R
Info
• When controlling the projector using RS-232C commands from a computer, wait for at least 30
seconds after the power has been turned on, and then transmit the commands.
• After sending an input selection or picture adjustment command and then receiving an “OK” re-
sponse code, the projector may take some time to process the command. If a second command is
sent while the projector is still processing the first command, you may receive an “ERR” response
code. If this happens, try resending the second command.
• When more than one code is being sent, send each command only after the response code for the
previous command from the projector is verified.
• “POWR????” “TABN _ _ _ 1” “TLPS _ _ _ 1” “TPOW _ _ _ 1” “TLPN _ _ _ 1” “TLTT _ _ _ 1”
“TLTM _ _ _ 1” “TLTL _ _ _ 1” “TNAM _ _ _ 1” “MNRD _ _ _ 1” “PJN0 _ _ _ 1”
- When the projector receives the special commands shown above:
* The on-screen display will not disappear.
* The “Auto Power Off” timer will not be reset.
- The special commands are available for applications that require continuous polling.
Note
•If an underbar (_) appears in the parameter column, enter a space.
•If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets
under Control Contents.
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.
*2 This command should be sent only after the “IRGB _ _ _ 2” command is sent and an “OK” response
code is received.
*3 The Lamp Timer Reset command is available only in standby mode.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Commands
Example: When turning on the projector, make the following setting.
Computer
Projector
→
←
P
O
W
R
_
_
_
1
O
K
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
(or 30-second startup time)
OK
OK or ERR
0
Power ON
OK or ERR
OK
1
_
_
_
_
_
_
1
0
?
1
P
P
P
T
O
O
O
A
W
W
W
B
R
R
R
N
Power
On
Off
Status
?
_
?
_
?
_
Projector Condition
0: Normal
0: Normal
1: Temp High
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
1: Temp High
2: Fan Error
4: Cover Open
8: Lamp Life 5% or less
16: Lamp Burn-out
32: Lamp Ignition Failure
64: Temp Abnormally High
0:Off, 4:Lamp Error
_
_
_
1
L
P
S
T
Status
0:Off, 1:On, 2:Retry
3:Waiting, 4:Lamp Error
1:On, 2:Cooling
1
Lamp
Name
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
1
1
1
*
0:Standby
P
L
L
L
L
N
N
J
O
P
T
T
T
A
R
N
W
N
T
M
L
M
D
1
T
T
T
T
T
T
M
P
Power Status
Quantity
0 – 9999(Integer)
0, 15, 30, 45
0% – 100%(Integer)
PGF312X/PGF262X/PGF212X
PG-F312X/PG-F262X/PG-F212X
OK or ERR
Usage Time(Hour)
Usage Time(Minute)
Life(Percentage)
Model Name Check
Model Name Check
Projector Name Setting 1
(First 4 characters) *1
Projector Name Setting 2
(Middle 4 characters) *1
Projector Name Setting 3
(Last 4 characters) *1
Projector Name Check
Computer
*
*
*
*
*
*
*
*
*
*
*
J
J
N
N
2
3
OK or ERR
P
P
OK or ERR
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
2
1
2
3
1
2
?
?
?
?
J
R
R
B
B
B
V
V
R
V
M
C
N
G
G
D
D
D
E
E
G
E
O
H
0
B
B
S
S
S
D
D
B
D
D
K
Projector Name
P
I
I
I
I
I
I
I
I
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Input Change
DVI
DVI-D-Computer select *2
DVI-D-Video select *2
DVI-Analog select *2
S-Video
Video
?
?
?
?
1:
Computer, 2: DVI or ERR
?
?
?
?
?
?
?
?
Input RGB Check
Input Video Check
Input Mode Check
Input Check
1: S-Video, 2: Video or ERR ERR
I
I
I
1: RGB, 2: Video
1: Computer
2: DVI
ERR
ERR
3: S-Video
4: Video
_
_
_
*
*
*
*
*
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
*
*
*
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
V
V
K
I
O
O
E
M
M
R
R
D
A
A
A
A
A
A
A
B
B
B
B
B
B
B
L
U
Y
B
B
E
E
J
S
S
S
S
S
S
S
S
S
S
S
S
S
S
A
D
S
K
K
Z
Volume
Volume(0 – 60)
Volume up/down(-10 – +10)
-80 – +80
On
Off
On
Off
Start
Computer
*
_
Keystone
AV Mute
_
_
1
0
1
0
1
1
2
3
5
6
0
1
1
2
3
5
6
0
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
F
F
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Freeze
Z
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Auto Sync
Resize
Normal
Stretch
Dot By Dot
Full
Border
Area Zoom
V-Stretch
Normal
Stretch
Dot By Dot
Full
1
1
_
_
_
_
_
DVI
Border
Area Zoom
V-Stretch
1
1
59
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands (Continued)
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
OK or ERR
(or 30-second startup time)
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
S-Video
1
2
3
0
1
1
2
3
0
1
1
0
1
2
3
4
*
V
V
V
V
V
V
V
V
V
V
E
S
S
S
S
S
I
R
R
R
R
R
R
R
R
R
R
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
A
A
A
A
A
B
B
B
B
B
L
S
S
S
S
S
S
S
S
S
S
R
P
P
P
P
P
P
B
R
B
C
T
S
C
W
I
Resize
Normal
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
Stretch
Border
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
1
1
_
_
_
Area Zoom
V-Stretch
Normal
Video
Stretch
Border
Area Zoom
V-Stretch
1
1
_
ALL Reset
Computer INPUT
Picture Mode
1
1
1
1
1
*
*
*
*
*
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
Standard
Presentation
Movie
Game
sRGB
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
*
*
*
*
*
*
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
*
*
*
*
R
D
E
O
I
*
*
*
*
*
H
T
E
P
P
P
R
R
R
E
I
_
*
*
TM
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
BrilliantColor
*
0 – +2
_
_
_
_
_
_
_
_
_
_
_
_
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
3
4
*
Progressive
2D Progressive
3D Progressive
Film Mode
Off
I
I
N
N
N
R
S
S
S
A
A
P
P
P
P
P
P
B
R
B
C
T
S
C
W
I
DNR
Level 1
Level 2
Picture Reset
Signal Type
Auto
I
I
I
I
I
I
RGB
Compontent
Audio 1
Audio 2
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
Audio Input
1
1
1
1
1
*
*
*
*
*
S
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
DVI INPUT
Picture Mode Standard
Presentation
Movie
Game
sRGB
*
*
*
*
*
*
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
BrilliantColor
Progressive
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
*
*
*
*
*
*
*
*
*
_
*
*
TM
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
0 – +2
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
2
0
1
2
1
0
1
2
1
2
0
1
2
2D Progressive
3D Progressive
Film Mode
Off
I
I
N
N
N
R
S
S
S
A
A
B
B
B
DNR
Level 1
Level 2
Picture Reset
Signal Type
Auto
I
I
I
I
I
I
RGB
Compontent
Audio 1
Audio 2
R
R
H
H
H
Audio Input
D
D
D
Dynamic Range Auto
Standard
Enhanced
60
Download from Www.Somanuals.com. All Manuals Search And Download.
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
Power ON
OK or ERR
(or 30-second startup time)
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
_
_
_
_
_
Picture Mode
0
1
2
3
*
*
*
*
*
1
1
1
1
*
*
*
*
*
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
N
N
A
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
I
S
S
S
S
I
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
I
S-Video INPUT
Standard
Presentation
Movie
_
_
_
_
_
_
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
Game
Contrast
Bright
Red
Blue
Color
Tint
Sharp
CLR Temp
*
*
*
*
*
*
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
R
D
E
O
I
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
*
*
*
_
*
*
_
*
*
*
H
T
E
P
P
P
R
R
R
E
I
TM
_
_
_
_
_
_
_
_
_
_
_
_
_
_
BrilliantColor
0 – +2
_
_
_
_
_
_
_
_
_
0
1
2
0
1
2
1
1
2
0
1
2
3
*
*
*
*
*
*
*
*
*
0
1
2
0
1
2
1
1
2
1
0
*
*
*
*
*
*
2
*
*
*
Progressive
2D Progressive
3D Progressive
Film Mode
Off
Level 1
Level 2
I
I
N
N
N
R
A
A
P
P
P
P
P
B
R
B
C
T
S
C
W
I
DNR
Picture Reset
Audio Input
Audio 1
Audio 2
I
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
S
S
S
S
I
R
D
E
O
I
H
T
E
P
P
P
R
R
R
E
I
Video INPUT
Picture Mode Standard
Presentation
Movie
Game
*
*
*
*
*
*
Contrast
Bright
Red
Blue
Color
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-30 – +30
-1 – +1
Tint
Sharp
*
_
CLR Temp
BrilliantColor
Progressive
TM
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2
2D Progressive
3D Progressive
Film Mode
Off
Level 1
Level 2
I
I
N
N
N
R
A
A
C
C
H
H
H
H
H
H
R
S
S
S
S
S
S
R
V
V
V
V
V
V
R
R
C
P
H
V
R
DNR
Picture Reset
Audio Input
Audio 1
Audio 2
I
1
0
*
*
*
*
*
*
_
S
S
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
E
L
C.M.S. Setting
C.M.S.
On
Off
Hue
*
*
*
*
*
Red
Yellow
Green
Cyan
Blue
*
_
Magenta
Reset
Red
Yellow
Green
Cyan
*
*
*
*
*
*
*
*
*
*
Saturation
*
*
*
3
*
*
*
*
*
Blue
*
_
*
_
Magenta
Reset
Red
Yellow
Green
Cyan
Blue
Magenta
Reset
*
*
*
*
*
*
_
_
*
*
*
*
*
*
_
_
Value
*
4
1
*
*
*
C.M.S. All Reset
-150 – +150
-30 – +30
-150 – +150
-60 – +60
*
*
*
*
_
*
*
*
Clock
Phase
H-position
V-position
H
P
P
E
I
I
I
I
*
_
*
*
*
_
_
_
1
Fine Sync Adjustment Reset
61
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Specifications and Commands (Continued)
RETURN
CONTROL CONTENTS
COMMAND
PARAMETER
Standby mode
(or 30-second startup time)
ERR
Power ON
OK or ERR
_
*
*
*
D
D
D
C
C
C
S
S
S
S
S
S
S
S
B
B
B
M
M
D
D
O
O
E
E
U
U
R
R
I
S
I
L
I
N
M
M
L
L
L
Image Shift
OSD Display
-96 – +96
On
Off
Off
CC1
CC2
Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
Logo
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
0
0
1
2
1
2
3
4
5
6
7
8
1
3
4
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
1
0
1
0
1
0
1
2
0
1
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
1
1
1
1
_
_
_
_
_
_
_
_
_
_
0
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
kHz(***.* or ERR)
Hz(***.* or ERR)
OK or ERR
OK or ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
ERR
OK or ERR
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
I
I
A
A
A
Y
Y
Y
Y
Y
Y
Y
Y
G
G
G
D
D
J
C
C
C
M
M
M
M
M
M
M
M
I
Closed Caption
Video System
E
E
E
E
E
E
E
E
M
M
M
H
H
A
A
P
P
R
R
O
O
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
S
S
S
F
Background
I
I
Blue
None
Bright
Eco + Quiet
On
Off
On
Off
On
Off
Standard
Eco
T
T
Lamp Setting
Auto Sync
A
A
A
A
A
A
M
M
I
J
W
W
S
S
T
Auto Power Off
Auto Restart
STANDBY Mode
PRJ Mode
T
On
Off
On
Off
E
E
N
N
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
U
U
D
D
K
K
Q
Q
D
D
E
Reverse
I
I
I
Invert
I
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
S
S
S
S
A
A
T
Language
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Türkçe
L
Magyer
On
Off
On
Off
On
Off
Horizontal
Vertical
Normal
High
G
G
N
N
P
P
R
R
M
M
R
Setup Guide
System Sound
Internal Speaker
RGB Frequency
Check
Fan Mode
T
F
L
L
P
H
H
L
0
0
Lamp Timer Reset *3
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15-110 kHz,
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-170 MHz
Sync signal: Compatible with TTL level
• Compatible with sync on green signal
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
Vertical Frequency
(Hz)
DVI-D
Support
Horizontal Frequency
(kHz)
Resolution
640 × 350
VESA Standard
Display
PC/MAC
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.0
66.2
67.5
64.0
80.0
64.0
65.3
75.0
34.9
49.7
60.2
68.7
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
70
75
60
75
60
60
60
67
75
75
75
✔
✔
✔
640 × 400
720 × 350
720 × 400
VGA
✔
✔
Upscale
640 × 480
✔
✔
✔
✔
✔
SVGA
XGA
800 × 600
PC
✔
✔
✔
✔
✔
✔
✔
✔
1024 × 768
True
1280 × 720
1280 × 768
1280 × 800
1280 × 800
1360 × 768
1366 × 768
✔
✔
✔
✔
WXGA
SXGA
Intelligent
Compression
1152 × 864
✔
✔
✔
1280 × 1024
1280 × 1024
SXGA+ 1400 × 1050
✔
✔
UXGA 1600 × 1200
VGA
SVGA
XGA
640 × 480
832 × 624
1024 × 768
MAC 13"
MAC 16"
MAC 19"
MAC 21"
Upscale
True
SXGA 1152 × 870
Intelligent Compression
Note
•When this projector receives 640K350 VESA format VGA signals, “640 × 400” appears on the screen.
•Optimum image quality will be achieved by matching your computer’s output resolution to the
resolution that corresponds to “True” in the “Display” column shown above.
Signal
480I
480P
540P
576I
576P
720P
720P
1035I
1080I
1080I
1080P
1080P
1080P
Horizontal Frequency (kHz) Vertical Frequency (Hz) DVI-D Support (Compatible with HDCP)
DTV
15.7
31.5
33.8
15.6
31.3
37.5
45.0
33.8
28.1
33.8
27.0
56.3
67.5
60
60
60
50
50
50
60
60
50
60
24
50
60
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
(DVI-D only)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Page
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
24
–
29
• Cables are incorrectly connected to the projector.
• Remote control battery has run out.
21–24
14
•
External output has not been set when connecting notebook computer. 21
No picture and no sound
or projector does not
start.
• The lamp unit cover is not installed correctly.
53, 54
•
If the connected DVI digital equipment is turned on before the “DVI-D” 21
input mode is selected on the projector, the image may not be
projected properly or may not be displayed at all. Ensure that the
appropriate input mode has been selected on the projector before you
turn on the connected equipment.
• Cables are incorrectly connected to the projector.
• “Bright” is set to minimum position.
21–24
41
• Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is
switched to the external output. Refer to the computer’s operation
manual for how to switch its signal output settings.
–
Sound is heard but no
picture appears
(or picture is dark).
• Image adjustments are incorrectly set.
41
48
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower
the “BrilliantColorTM” value.
(Video Input only)
• Video input system is incorrectly set.
Color is faded or poor.
• Adjust the focus.
• The projection distance exceeds the focus range.
26
20
–
•
There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the
surface of the lens and the image will become blurred. Set up the
projector at least one hour before it is to be used. If condensation should
form, remove the power cord from the wall outlet and wait for it to clear.
Picture is blurred;
noise appears.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
48
48
–
• Cables are incorrectly connected to the projector.
21–24
• Volume is set to minimum.
29
• When the projector is connected to an external device and the
volume is set to minimum, the sound is not output even if you turn up
the volume of the external device.
Picture appears but no
sound is heard.
• “Speaker” is set to “Off”.
45
Data image is not
centered.
• Select “Data image is not centered” in the “Help” menu and make the 48
necessary adjustments.
• Depending on the computer you are using, the output resolution
signal may be different from the one you have set. For details, refer to
the operation manual of the computer.
–
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Page
An unusual sound is
occasionally heard from
the cabinet.
• If the picture is normal, the sound is due to cabinet shrinkage caused
by room temperature changes. This will not affect operation or
performance.
–
Maintenance indicator on • See “Maintenance Indicators”.
the projector illuminates
50
47
or blinks in red.
The projector cannot
be turned on or put into
the standby mode
• The keylock is set.
If the keylock is set to “ON”, all the buttons are locked.
using STANDBY/ON on
the projector.
Picture is green on
COMPUTER
(Component)/
• Change the input signal type setting.
48
40, 48
• When you cannot select an input signal type, select “Color is faded
or poor” in the “Help” menu, after selecting an item other than
“sRGB” in “Picture Mode”, and then select an input signal type.
DVI (Component).
Picture is pink
(no green) on
COMPUTER (RGB)/
DVI (RGB).
Picture is too bright and • Image adjustments are incorrectly set.
whitish.
41
The cooling fan becomes • When temperature inside the projector increases, the cooling fan
8, 9
49, 50, 51
noisy.
runs faster.
The lamp does not light • The lamp indicator is illuminating in red.
up even after the
projector turns on.
Replace the lamp.
50, 53
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
• Cables are incorrectly connected to the projector or the connected
equipment works improperly.
• Select “Vertical stripes or flickering image appear” in the “Help”
menu and make the necessary adjustments.
21–24
48
• If this happens frequently, replace the lamp.
53
53
The lamp needs much • The lamp will eventually need to be changed.
time to turn on.
While the remaining lamp life draws to a close, replace the lamp.
Picture is dark.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector’s remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the
projector’s remote control sensor, place the projector where it will not
be affected by strong light.
15
• The batteries may be depleted or inserted incorrectly. Make sure the 14
batteries are inserted correctly or insert new ones.
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
refer to the“Troubleshooting”section on pages 64 and 65. If this operation manual
does not answer your question, please contact the SHARP Service departments
listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
Canada
Mexico
Sharp Electronics of Canada Ltd.
(905) 568-7140
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972
Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277
Singapore
Hong Kong
Taiwan
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
Germany
U.K.
Sharp Electronics (Europe) GMBH
01805-234675
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
Sharp Electronics (U.K.) Ltd.
08705 274277
Sharp Corporation (Taiwan)
0800-025111
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
Malaysia
U.A.E.
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
France
Sharp Electronics France
01 49 90 35 40
Sharp Middle East Fze
971-4-81-5311
Spain
Sharp Electronica Espana, S.A.
93 5819700
Thailand
Korea
Sharp Thebnakorn Co. Ltd.
02-236-0170
Switzerland
Sweden
Austria
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Model
PG-F312X/PG-F262X/PG-F212X
Display devices
Resolution
0.55" DLP® Chip
XGA (1024 × 768)
F number
Lens
F 2.5 – 2.6
Zoom
Manual, ×1.15 (f = 20.4 – 23.5 mm)
Focus
Manual
DVI-I (Compatible with HDCP)
RGB/Component (mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
Input terminals
×1
×1
×1
×1
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
×1
×1 (L/R)
RGB/Component (mini D-sub 15 pin)
Audio (ø3.5 mm stereo minijack)
USB (Type B)
Output terminals
Control, others
×1
×1 (variable audio output)
×1
RS-232C (mini DIN 9 pin)
×1
Speakers
2 W (Mono)
Projection lamp
PG-F312X
PG-F262X
PG-F212X
AC 100 – 240 V
50/60 Hz
250 W
230 W
200 W
Rated voltage
Rated frequency
Input current
PG-F312X
PG-F262X
PG-F212X
PG-F312X
3.4 A
3.2 A
2.9 A
326 W (5.0 W) with AC 100 V
316 W (5.7 W) with AC 240 V
303 W (5.0 W) with AC 100 V
293 W (5.7 W) with AC 240 V
267 W (5.0 W) with AC 100 V
259 W (5.7 W) with AC 240 V
Power consumption (Standby)
PG-F262X
PG-F212X
41°F to 95°F (+5°C to +35°C)
Plastic
10 41/64" × 3 33/64" × 10 7/16"
(270 (W) × 89 (H) × 265 (D) mm)
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
6.4 lbs. (2.9 kg)
Weight (approx.)
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specifica-
tion figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Units: inches (mm)
2 61/64 (75)
10 41/64 (270)
2 3
/8 (60)
M4
M4
M4
M4
13/32 (10)
13/32 (10)
1 27/64
(36)
2 61/64 (75)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Accessories ............................................................. 10
AC socket ................................................................ 24
Adjustment buttons ................................................. 38
AREA ZOOM ........................................................... 31
Aspect ratio ............................................................. 30
Audio Input .............................................................. 46
AUDIO 1, 2 terminal ................................................ 23
AUDIO OUT terminal .............................................. 23
Auto Power Off ........................................................ 45
Auto Restart ............................................................ 45
Auto Sync (Auto Sync adjustment) ....... 33, 37, 45, 48
AUTO SYNC button ................................................. 33
AV MUTE button ...................................................... 29
L-CLICK button ........................................................ 34
Lens Cap ................................................................. 11
MAGNIFY buttons ................................................... 33
MENU/HELP button .......................................... 38, 48
MONITOR OUT terminal ......................................... 23
MOUSE/Adjustment buttons ............................. 34, 38
NORMAL ........................................................... 30, 31
ON button ................................................................ 25
Optional accessories ............................................... 10
OSD Display ............................................................ 43
PAGE DOWN button ................................................ 34
PAGE UP button ...................................................... 34
PDF ............................................................................ 9
Picture Adjustment .................................................. 40
Picture Mode ..................................................... 33, 40
PICTURE MODE button .......................................... 33
POINTER button ..................................................... 32
Power cord ............................................................... 24
Power indicator ........................................................ 50
PRJ - ADJ ................................................................ 45
PRJ Mode .......................................................... 19, 44
Progressive .............................................................. 42
Background ............................................................. 44
Batteries .................................................................. 14
Blue .......................................................................... 41
BORDER ........................................................... 30, 31
BREAK TIMER button ............................................. 32
Bright ....................................................................... 41
BrilliantColorTM ......................................................... 41
Closed Caption ........................................................ 44
CLR Temp (Color Temperature) .............................. 41
C.M.S. ...................................................................... 41
Color ........................................................................ 41
COMPUTER button ................................................. 29
COMPUTER/COMPONENT input terminal ...... 21, 22
Contrast ................................................................... 41
R-CLICK/RETURN button ................................. 34, 38
Rear adjustment foot ............................................... 27
Red .......................................................................... 41
Remote control ........................................................ 13
Remote control sensor ............................................ 15
Replacing the lamp ........................................... 52, 53
Resize ................................................................ 30, 43
RESIZE button ........................................................ 30
RGB cable ............................................................... 21
RS-232C terminal .................................................... 24
DIN-D-sub RS-232C adaptor .................................. 24
DNR ......................................................................... 42
DOT BY DOT ........................................................... 30
DVI button ................................................................ 29
DVI-I input terminal ........................................... 21, 22
ECO+QUIET button ................................................ 32
ENTER button ......................................................... 38
Exhaust vent ...................................................... 12, 49
SCR - ADJ ............................................................... 43
Screen Size and Projection Distance ..................... 20
Setup Guide....................................................... 26, 44
Sharp ....................................................................... 41
Speaker ................................................................... 45
SPOT button ............................................................ 32
STANDBY button ..................................................... 25
STANDBY Mode ...................................................... 45
STANDBY/ON button .............................................. 25
Storage case ........................................................... 55
STRETCH .......................................................... 30, 31
Supplied accessories .............................................. 10
S-VIDEO button ....................................................... 29
S-VIDEO terminal .................................................... 22
System Lock ............................................................ 46
System Sound ......................................................... 45
Fan Mode ................................................................. 46
Fine Sync................................................................. 48
Focus ring ................................................................ 26
FREEZE button ....................................................... 33
Front adjustment foot .............................................. 27
FULL ........................................................................ 30
HEIGHT ADJUST lever ........................................... 27
Help ......................................................................... 48
H-Pos ................................................................. 37, 48
Image shift ............................................................... 43
INPUT modes .......................................................... 29
Intake vent ......................................................... 11, 49
Kensington Security Standard connector ............... 12
Keycode ................................................................... 46
Keylock .................................................................... 47
KEYSTONE button .................................................. 28
Keystone Correction .......................................... 28, 43
Temperature warning indicator ............................... 50
Tint ........................................................................... 41
USB terminal ........................................................... 34
VIDEO button .......................................................... 29
VIDEO terminal ....................................................... 22
VOL (Volume) buttons ............................................. 29
V-Pos ................................................................. 37, 48
V-STRETCH ............................................................ 31
Lamp ........................................................................ 52
Lamp indicator ......................................................... 50
Lamp Setting ........................................................... 42
Lamp Timer (Life) .................................................... 47
Lamp unit ................................................................. 53
Language (on-screen display language) ................ 44
Zoom ring ................................................................ 26
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|