Sharp Projection Television PGLW2000 User Manual
DATA PROJECTOR  
MODEL  
PG-LW2000  
OPERATION MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using the projector, please read this operation manual carefully.  
ENGLISH  
Introduction  
There are two important reasons for prompt warranty registration of your new  
SHARP Projector, using the REGISTRATION CARD packed with the projector.  
1. WARRANTY  
This is to assure that you immediately receive the full benefit of the parts,  
service and labor warranty applicable to your purchase.  
2. CONSUMER PRODUCT SAFETY ACT  
To ensure that you will promptly receive any safety notification of inspection,  
modification, or recall that SHARP may be required to give under the 1972  
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT  
“LIMITED WARRANTY” CLAUSE.  
U.S.A. ONLY  
High brightness light source. Do not stare into the beam of light, or view  
directly. Be especially careful that children do not stare directly into the  
beam of light.  
WARNING:  
To reduce the risk of fire or electric shock, do not  
expose this product to rain or moisture.  
WARNING:  
See bottom of projector.  
The lightning flash with arrowhead sym-  
bol, within an equilateral triangle, is in-  
tended to alert the user to the presence  
of uninsulated “dangerous voltage”  
within the product's enclosure that may  
be of sufficient magnitude to constitute  
a risk or electric shock to persons.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
DO NOT REMOVE SCREWS  
EXCEPT SPECIFIED USER  
SERVICE SCREW.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER.  
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
The exclamation point within a triangle  
is intended to alert the user to the pres-  
ence of important operating and main-  
tenance (servicing) instructions in the  
literature accompanying the product.  
WARNING:  
This is a Class A product. In a domestic environment this product may cause  
radio interference in which case the user may be required to take adequate  
measures.  
FCC Regulations state that any unauthorized changes or modifications  
to this equipment not expressly approved by the manufacturer could  
WARNING:  
void the user's authority to operate this equipment.  
U.S.A. ONLY  
The enclosed computer cable must be used with the device. The cable is  
provided to ensure that the device complies with FCC Class A verification.  
U.S.A. ONLY  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with  
the operation manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference, in which case the user will be required to correct the interference at  
his own expense.  
U.S.A. ONLY  
PRODUCT DISPOSAL  
This product utilizes lamp containing a small amount of mercury.  
Disposal of these materials may be regulated due to environmental  
considerations. For disposal or recycling information, please contact  
your local authorities, the Electronics Industries Alliance: www.eiae.org,  
the lamp recycling organization www.lamprecycle.org, or Sharp at  
1-800-BE-SHARP.  
U.S.A. ONLY  
Caution Concerning Lamp Replacement  
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp  
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface  
scratches or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition  
and the frequency of use. It is important to note that failure can often result in the bulb cracking.  
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended  
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating  
normally.  
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the  
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector  
Dealer or Service Center to assure safe operation.  
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In  
case of exposure to the gas, consult a doctor as soon as possible.  
Caution  
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may  
cause burns or injury.  
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to  
fully cool before removing the lamp unit.  
• Do not touch the glass surface of the lamp unit or the inside of the projector.  
• Do not loosen other screws except for the lamp unit cover and lamp unit.  
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and  
continue to use the same lamp, this may cause the lamp to become damaged or explode.  
■ Carefully change the lamp by following the instructions described on pages 56 to 58.  
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector  
Dealer or Service Center.  
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized  
Projector Dealer or Service Center for repair.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Accessories  
Supplied accessories  
Two LR03 batteries  
(“AAA” size, UM/SUM-4,  
HP-16 or similar)  
RGB cable  
(6' (1.8 m))  
<QCNWGA173WJPZ>  
Remote control  
<RRMCGB015WJSA>  
Power cord*  
(1)  
(2)  
(3)  
(4)  
For U.S. and  
Canada, etc.  
(6' (1.8 m))  
For Europe,  
except U.K.  
(6' (1.8 m))  
For U.K. and  
Singapore  
(6' (1.8 m))  
For Australia, New  
Zealand and Oceania  
(6' (1.8 m))  
<QACCDA083WJPZ> <QACCVA025WJPZ> <QACCBA105WJPZ> <QACCLA056WJPZ>  
* Which power cords are supplied along with your projector depends on the region. Use the power  
cord that corresponds to the wall outlet in your country.  
• Initial setup guide <TINS-F582WJZZ>  
• CD-ROM <UDSKAA137WJN1>  
Note  
• Codes in “< >” are Replacement parts codes.  
Optional accessories  
AN-LX20LP  
AN-60KT  
AN-XRCM30 (for U.S.A. only)  
AN-TK201 <for AN-60KT>  
AN-TK202 <for AN-60KT>  
AN-EP101B <for AN-XRCM30>  
(for U.S.A. only)  
■ Lamp unit  
■ Ceiling-mount adaptor  
■ Ceiling-mount bracket  
■ Ceiling-mount unit  
■ Ceiling-mount extension tube  
AN-C3CP2  
■ 3 RCA to mini D-sub 15 pin cable (10n (3.0 m))  
Note  
• Some of the optional accessories may not be available depending on the region. Please check with  
your nearest Sharp Authorized Projector Dealer or Service Center.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Preparing  
Introduction  
Useful Features  
Accessories............................................3  
Contents.................................................4  
IMPORTANT SAFEGUARDS ..................6  
Part Names and Functions...................10  
Top View ................................................ 10  
Front View.............................................. 10  
Rear View (Terminals).............................. 11  
Inserting the Batteries............................. 13  
Usable Range......................................... 13  
Operating with the Remote Control......30  
Displaying and Setting the  
Break Timer......................................... 30  
Displaying the Pointer............................. 30  
Using the Spot Function......................... 30  
Switching the Eco+Quiet Mode .............. 30  
Auto Sync (Auto Sync Adjustment) ......... 31  
Freezing a Moving Image........................ 31  
Selecting the Picture Mode..................... 31  
Displaying an Enlarged Portion of  
an Image ............................................. 31  
Menu Items...........................................32  
Using the Menu Screen........................35  
Menu Selections (Quick Start Menu) .........35  
Quick Start Menu.................................... 36  
Menu Selections (Complete Menu) .......... 36  
Picture Adjustment (“Picture” Menu) ....38  
Selecting the Picture Mode..................... 38  
Adjusting the Image................................ 39  
Adjusting the Color Temperature............. 39  
Adjusting the Colors ............................... 39  
Selecting the Film Mode ......................... 40  
Reducing Image Noise (DNR) ................. 40  
Eco+Quiet.............................................. 40  
Signal Adjustment (“SIG-ADJ” Menu) ..41  
Adjusting the Computer Image ............... 41  
Resolution Setting .................................. 41  
Signal Type Setting................................. 41  
Selecting the Dynamic Range................. 41  
Setting the Video System ....................... 42  
Setting the Video Setup.......................... 42  
Checking the Input Signal....................... 42  
Adjusting the Projected Image  
Easy Start  
Easy Start.............................................14  
Setup and Projection.............................. 14  
Setup  
Setting Up the Projector.......................16  
Video Setup............................................ 16  
Setting Up the Projector ......................... 16  
Standard Setup (Front Projection)........... 16  
Screen Size and Projection Distance ...... 17  
Projection (PRJ) Mode............................ 18  
Ceiling-Mount Setup............................... 18  
Connections  
Connecting the Projector to  
Other Equipment................................19  
Connecting the Power Cord.................21  
Controlling the Projector by  
(“SCR-ADJ” Menu).............................43  
Setting the Resize Mode......................... 43  
Adjusting the Image Position .................. 43  
Keystone Correction............................... 43  
Setting the Overscan.............................. 44  
Setting the On-screen Display ................ 44  
Closed Caption ...................................... 44  
Selecting the Background Image............ 45  
Selecting the Setup Guide...................... 45  
Reversing/Inverting Projected Images..... 45  
Selecting the Wall Color.......................... 45  
Selecting the On-screen Display Language ... 45  
Adjusting the Projector Function  
(“PRJ-ADJ1/2” Menu) ........................46  
Auto Sync (Auto Sync Adjustment) ......... 46  
Auto Power Off Function ........................ 46  
Auto Restart Function............................. 46  
Speaker Setting...................................... 46  
Fan Mode Setting................................... 46  
System Lock Function............................ 47  
a Computer........................................22  
Using  
Basic Operation  
Turning the Projector On/Off ................23  
Turning the Projector On......................... 23  
Turning the Power Off (Putting the  
Projector into Standby Mode) .............. 23  
Image Projection ..................................24  
About the Setup Guide........................... 24  
Adjusting the Projected Image................ 24  
Correcting Trapezoidal Distortion............ 26  
Switching the Input Mode....................... 27  
Adjusting the Volume.............................. 27  
Displaying the Black Screen and  
Turning Off the Sound Temporarily ....... 27  
Resize Mode .......................................... 28  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Keylock Function.................................... 48  
Selecting the Quick Start Menu .............. 49  
Setting the FUNCTION Button Operation.. 49  
STANDBY Mode..................................... 49  
DLP® LinkTM............................................ 49  
DLP® LinkTM Invert .................................. 49  
Returning to the Default Settings ............ 49  
Checking the Lamp Life Status............... 49  
Viewing Stereoscopic 3D Images.........50  
Precautions on Viewing Stereoscopic  
3D Images........................................... 50  
Information on the 3D Projection  
Function .............................................. 51  
Appendix................................................ 51  
Using 3D Viewing Mode ......................... 52  
Reference  
Appendix  
Maintenance.........................................53  
Maintenance Indicators........................54  
Regarding the Lamp.............................56  
Lamp...................................................... 56  
Caution Concerning the Lamp................ 56  
Replacing the Lamp ............................... 56  
Removing and Installing the Lamp Unit... 57  
Resetting the Lamp Timer ...................... 58  
RS-232C Specifications and Commands...59  
Compatibility Chart ..............................64  
Troubleshooting....................................66  
For SHARP Assistance.........................69  
Specifications.......................................70  
Dimensions...........................................71  
Index.....................................................72  
•
In this operation manual, the illustration and the screen display are simplified for explanation, and  
may differ slightly from the actual display.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS  
CAUTION: Please read all of these instructions before you operate this  
product and save these instructions for later use.  
Electrical energy can perform many useful functions. This product has been engineered  
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN  
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the  
safeguards incorporated in this product, observe the following basic rules for its  
installation, use and servicing.  
1. Read Instructions  
10. Ventilation  
Slots and openings in the cabinet are provided  
All the safety and operating instructions  
should be read before the product is  
operated.  
for ventilation to ensure reliable operation of  
the product and to protect it from overheating,  
and these openings must not be blocked or  
covered. The openings should never be  
blocked by placing the product on a bed, sofa,  
rug, or other similar surface. This product  
should not be placed in a built-in installation  
such as a bookcase or rack unless proper  
ventilation is provided or the manufacturer's  
instructions have been adhered to.  
2. Retain Instructions  
The safety and operating instructions  
should be retained for future reference.  
3. Heed Warnings  
All warnings on the product and in the  
operating instructions should be adhered to.  
4. Follow Instructions  
All operating and use instructions should  
be followed.  
11. Power Sources  
This product should be operated only from  
the type of power source indicated on the  
marking label. If you are not sure of the  
type of power supply to your home, consult  
your product dealer or local power  
company. For products intended to operate  
from battery power, or other sources, refer  
to the operating instructions.  
5. Cleaning  
Unplug this product from the wall outlet before  
cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
6. Attachments  
Do not use attachments not recommended by the  
product manufacturer as they may cause hazards.  
7. Water and Moisture  
Do not use this product near water–for  
example, near a bath tub, wash bowl, kitchen  
sink, or laundry tub; in a wet basement; or  
near a swimming pool; and the like.  
8. Accessories  
12. Grounding or Polarization  
This product is provided with one of the  
following types of plugs. If the plug should  
fail to fit into the power outlet, please contact  
your electrician.  
Do not defeat the safety purpose of the plug.  
a. Two-wire type (mains) plug.  
b. Three-wire grounding type (mains) plug  
with a grounding terminal.  
Do not place this product on an unstable  
cart, stand, tripod, bracket, or table. The  
product may fall, causing serious injury to a  
child or adult, and serious damage to the  
product. Use only with a cart, stand, tripod,  
bracket, or table recommended by the  
manufacturer, or sold with the product. Any  
mounting of the product should follow the  
manufacturer's instructions, and should use a  
mounting accessory recommended by the  
manufacturer.  
This plug will only fit into a grounding  
type power outlet.  
13. Power-Cord Protection  
Power-supply cords should be routed so  
that they are not likely to be walked on or  
pinched by items placed upon or against  
them, paying particular attention to cords  
at plugs, convenience receptacles, and the  
point where they exit from the product.  
9. Transportation  
14. Lightning  
A product and cart  
For added protection for this product during  
a lightning storm, or when it is left  
unattended and unused for long periods of  
time, unplug it from the wall outlet and  
disconnect the cable system. This will  
prevent damage to the product due to  
lightning and power-line surges.  
combination should be  
moved with care. Quick  
stops, excessive force, and  
uneven surfaces may  
cause the product and cart  
combination to overturn.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
15. Overloading  
19. Replacement Parts  
Do not overload wall outlets, extension cords,  
or integral convenience receptacles as this  
can result in a risk of fire or electric shock.  
16. Object and Liquid Entry  
Never push objects of any kind into this  
product through openings as they may touch  
dangerous voltage points or short-out parts  
that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
17. Servicing  
When replacement parts are required, be  
sure the service technician has used  
replacement parts specified by the  
manufacturer or have the same  
characteristics as the original part.  
Unauthorized substitutions may result in  
fire, electric shock, or other hazards.  
20. Safety Check  
Upon completion of any service or repairs  
to this product, ask the service technician  
to perform safety checks to determine that  
the product is in proper operating  
condition.  
Do not attempt to service this product  
yourself as opening or removing covers  
may expose you to dangerous voltage or  
other hazards. Refer all servicing to  
qualified service personnel.  
21. Wall or Ceiling Mounting  
This product should be mounted to a wall  
or ceiling only as recommended by the  
manufacturer.  
18. Damage Requiring Service  
Unplug this product from the wall outlet  
and refer servicing to qualified service  
personnel under the following conditions:  
a. When the power-supply cord or plug is  
damaged.  
22. Heat  
This product should be situated away from  
heat sources such as radiators, heat  
registers, stoves, or other products  
(including amplifiers) that produce heat.  
b. If liquid has been spilled, or objects  
have fallen into the product.  
c. If the product has been exposed to rain  
or water.  
d. If the product does not operate normally  
by following the operating instructions.  
Adjust only those controls that are  
covered by the operating instructions,  
as an improper adjustment of other  
controls may result in damage and will  
often require extensive work by a  
qualified technician to restore the  
product to normal operation.  
e. If the product has been dropped or  
damaged in any way.  
f. When the product exhibits a distinct  
change in performance, this indicates a  
need for service.  
• DLP® and the DLP logo are registered trademarks of Texas Instruments and  
BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.  
• PC/AT is a registered trademark of International Business Machines Corporation in the  
United States.  
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or  
other countries.  
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or  
registered trademarks of HDMI Licensing LLC.  
• All other company or product names are trademarks or registered trademarks of their  
respective companies.  
•Some IC chips in this product include confidential and/or trade secret property belonging  
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,  
reverse engineer, reverse assemble or discompile the contents thereof.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Observe the following safeguards when setting up your  
projector.  
Caution concerning the lamp unit  
When using the projector in high-  
altitude areas such as mountains (at  
altitudes of approximately 1,500  
meters (4,900 feet) or more)  
■ When you use the projector in high-altitude  
areas with thin air, set “Fan Mode” to  
“High”. Neglecting this can affect the  
longevity of the optical system.  
■ Potential hazard of glass particles if lamp  
ruptures. In case of lamp rupture, contact  
your nearest Sharp Authorized Projector  
Dealer or Service Center  
for replacement.  
See “Regarding the Lamp”  
on page 56.  
■ Use the projector at altitudes of 2,300  
meters (7,500 feet) or less.  
Caution concerning the setup of the  
projector  
Warning about placing the projector in  
a high position  
■ When placing the projector in a high  
position, make certain it is carefully secure  
to avoid personal injury caused by the  
projector falling down.  
■ For minimal servicing and to maintain high  
image quality, SHARP recommends that  
this projector be installed in an area free  
from humidity, dust and cigarette smoke.  
When the projector is subjected to these  
environments, the vents and lens must be  
cleaned more often. As long as the  
projector is regularly cleaned, use in these  
environments will not reduce the overall  
operation life of the unit. Internal cleaning  
should only be performed by a Sharp  
Authorized Projector Dealer or Service  
Center.  
Do not subject the projector to hard  
impact and/or vibration.  
■ Protect the lens so as not to hit or damage  
the surface of the lens.  
Avoid locations with extremes of  
temperature.  
■ The operating temperature of the projector  
is from 41°F to 95°F (+5°C to +35°C).  
■ The storage temperature of the projector is  
from –4°F to 140°F (–20°C to +60°C).  
Rest your eyes occasionally.  
■ Continuously watching the screen for long  
hours will cause eye strain. Take regular  
breaks to rest your eyes.  
Do not set up the projector in places  
exposed to direct sunlight or bright light.  
■ Position the screen so that it is not in direct  
sunlight or room light. Light falling directly  
on the screen washes out the colors,  
making viewing difficult. Close the curtains  
and dim the lights when setting up the  
screen in a sunny or bright room.  
Do not block the exhaust and intake  
vents.  
■ Allow at least 11 13  
/16 inches (30 cm) of  
space between the exhaust vent and the  
nearest wall or obstruction.  
■ Ensure that the intake vent and the exhaust  
vent are not obstructed.  
■ If the cooling fan becomes obstructed, a  
protection circuit will automatically put the  
projector into Standby mode to prevent  
overheat damage. This does not indicate a  
malfunction. (See pages 54 and 55.)  
Remove the projector power cord from the  
wall outlet and wait at least 10 minutes.  
Place the projector where the intake and  
exhaust vents are not blocked, plug the  
power cord back in and turn on the  
projector. This will return the projector to  
the normal operating condition.  
Caution regarding placing of the projector  
■ Place the projector on a level site within the  
adjustment range (9 degrees) of the  
adjustment foot.  
■ After the projector is purchased, a faint  
smell from the vent may appear when the  
power is first turned on. This is normal and  
is not a malfunction. It will disappear after  
the projector is used for a while.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution regarding usage of the projector Temperature monitor function  
■ If you are not to use the projector for a long  
time or before moving the projector, make  
certain you unplug the power cord from the  
wall outlet, and disconnect any other  
cables connected to it.  
■ If the temperature inside the projector  
■ Do not carry the projector by holding the  
increases, due to blockage of the air vents,  
or the setting location, the temperature  
lens.  
■ Do not expose the projector to direct  
warning indicator will blink. And if the  
temperature keeps on rising, “  
sunlight or place next to heat sources.  
Doing so may affect the cabinet color or  
cause deformation of the plastic cover.  
” will  
illuminate in the lower left corner of the  
picture with the temperature warning  
indicator blinking. If this state continues,  
the lamp will turn off, the cooling fan will  
run and then the projector will enter  
Standby mode. Refer to “Maintenance  
Indicators” on pages 54 and 55 for details.  
Other connected equipment  
■ When connecting a computer or other  
audio-visual equipment to the projector,  
make the connections AFTER unplugging  
the power cord of the projector from the  
AC outlet and turning off the equipment to  
be connected.  
■ Please read the operation manuals of the  
projector and the equipment to be  
connected for instructions on how to make  
the connections.  
Info  
• The cooling fan regulates the internal  
temperature, and its performance is automatically  
controlled. The sound of the fan may change  
during projector operation due to changes in the  
fan speed. This does not indicate malfunction.  
Using the projector in other countries  
■ The power supply voltage and the shape of  
the plug may vary depending on the region  
or country you are using the projector in.  
When using the projector overseas, make  
sure you use an appropriate power cord for  
the country you are in.  
Closed Caption uses Bitstream Vera fonts  
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.  
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this  
license (“Fonts”) and associated documentation files (the “Font Software”), to reproduce and distribute the  
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell  
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject  
to the following conditions:  
The above copyright and trademark notices and this permission notice shall be included in all copies of one  
or more of the Font Software typefaces.  
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or  
characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts,  
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.  
This License becomes null and void to the extent applicable to Fonts or Font Software that has been  
modified and is distributed under the “Bitstream Vera” names.  
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font  
Software typefaces may be sold by itself.  
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR  
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A  
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER  
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,  
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR  
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING  
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN  
THE FONT SOFTWARE.  
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall  
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software  
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further  
information, contact: fonts at gnome dot org.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions  
Numbers in Zrefer to the main pages in this operation manual where the  
topic is explained.  
1
2
11  
12  
3
8
9
4
5
13  
14  
6
7
10  
15 16 17  
Top View  
Front View  
1
2
3
4
Temperature warning indicator  
11 Zoom ring  
54  
25  
For enlarging/reducing the picture.  
Lamp indicator  
Power indicator  
54  
54  
12 Focus ring  
24  
For adjusting the focus.  
23  
STANDBY/ON button  
For turning the power on and putting the  
projector into Standby mode.  
13 Intake vent  
14 Security bar  
15 HEIGHT ADJUST lever  
16 Adjustment foot  
17 Remote control sensor  
53  
5
ENTER button  
35  
25  
13  
For setting items selected or adjusted on  
the menu.  
25  
6
7
VOL (Volume) buttons (–O/Q+)  
27  
For adjusting the speaker sound level.  
AUTO SYNC button  
For automatically adjusting images when  
connected to a computer.  
31  
8
9
Adjustment buttons (P/R/O/Q)  
35  
For selecting menu items.  
INPUT buttons (P/R)  
27  
For switching Input mode.  
10 MENU button  
35  
For displaying adjustment and setting  
screens.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
2
3
4
5
6
7
8
9
10  
Rear View (Terminals)  
19, 20, 21  
1
HDMI terminal  
Terminal for HDMI input.  
2
3
AUDIO input terminal  
VIDEO input terminal  
Terminal for connecting video equipment.  
21  
20  
4
COMPUTER/COMPONENT input  
terminal  
19, 20  
Terminal for computer RGB and  
component signals.  
22  
5
RS-232C terminal  
Terminal for controlling the projector using  
a computer.  
6
7
8
Exhaust vent  
53  
Speaker  
46  
Using the Kensington Lock  
• This projector has a Kensington Security  
Standard connector for use with a  
Kensington MicroSaver Security System.  
Refer to the information that came with the  
system for instructions on how to use it to  
secure the projector.  
Kensington Security Standard  
connector  
9
Rear adjustment foot  
25  
10 AC socket  
21  
Connect the supplied power cord.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Functions (Continued)  
Numbers in Zrefer to the main pages in this operation manual where the  
topic is explained.  
8
9
30  
POINTER button  
1
2
For displaying the pointer.  
35  
Adjustment buttons (P/R/O/Q)  
For selecting and adjusting menu items.  
13  
14  
3
4
5
6
7
8
9
10  
11  
EFFECT button  
For changing the pointer or spot area.  
30  
15  
16  
17  
18  
26  
KEYSTONE button  
For entering the Keystone Correction  
mode.  
12  
FUNCTION button  
For operating and executing a function  
assigned to “FUNCTION Button”.  
49  
19  
20  
21  
10  
11  
13  
VOL +/– (Volume) buttons  
For adjusting the speaker sound level.  
27  
14  
27  
INPUT buttons (P/R)  
For switching Input mode.  
22  
12  
15  
31  
PICTURE MODE button  
For selecting the appropriate picture.  
31, 46  
16 AUTO SYNC button  
For automatically adjusting images when  
connected to a computer.  
17  
18  
28  
RESIZE button  
1
2
ON button  
For turning the power on.  
23  
For switching the picture size (NORMAL,  
16:9, etc.).  
23  
STANDBY button  
For putting the projector into the Standby  
mode.  
35  
MENU button  
For displaying adjustment and setting  
screens.  
3
4
5
6
MAGNIFY buttons  
For enlarging/reducing part of the image.  
31  
19  
20  
21  
ENTER button  
35  
For setting items selected or adjusted on  
the menu.  
31  
FREEZE button  
For freezing images.  
35  
RETURN button  
For returning to the previous menu screen  
during menu operations.  
30  
BREAK TIMER button  
For displaying the break time.  
30  
ECO+QUIET button  
For lowering the noise of the cooling fan  
and extending the lamp life.  
27  
AV MUTE button  
For temporarily displaying a black screen  
and turning off the sound.  
22  
3D MODE button  
For displaying the 3D MODE menu screen.  
52  
7
SPOT button  
For displaying the spotlight.  
30  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Inserting the Batteries  
Pull down the tab on the cover and remove the  
cover towards the direction of the arrow.  
1
Insert the batteries.  
2
• Insert the batteries making sure the polarities correctly match  
the mand nmarks inside the battery compartment.  
Insert the lower tab of the cover into the opening,  
and lower the cover until it clicks in place.  
3
Incorrect use of the batteries may cause them to leak or explode.  
Please follow the precautions below  
Caution  
• Danger of explosion if battery is incorrectly replaced.  
Replace only with alkaline or manganese batteries.  
• Insert the batteries making sure the polarities correctly match the mand nmarks inside the battery  
compartment.  
• Batteries of different types have different properties, therefore do not mix batteries of different types.  
• Do not mix new and old batteries.  
This may shorten the life of new batteries or may cause old batteries to leak.  
•
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.  
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then  
remove them using a cloth.  
• The batteries included with this projector may run down in a short period, depending on how they are kept.  
Be sure to replace them as soon as possible with new batteries.  
• Remove the batteries from the remote control if you will not be using the remote control for a long time.  
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.  
Remote control sensor  
Usable Range  
The remote control can be used to control the  
projector within the ranges shown in the  
illustration.  
Note  
• The signal from the remote control can be  
reflected off a screen for easy operation.  
However, the effective distance of the signal  
may differ depending on the screen material.  
30°  
30°  
When using the remote control  
• Ensure that you do not drop it or expose it to  
moisture or high temperature.  
33n (10 m)  
• The remote control may malfunction under a  
fluorescent lamp. In this case, move the  
projector away from the fluorescent lamp.  
Remote control signal  
transmitters  
Remote control  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Easy Start  
This section shows the basic operation (projector connecting with the computer). For details,  
see the page described below for each step.  
Setup and Projection  
In this section, connection of the projector and the computer is explained using one example.  
3
8
8 STANDBY button  
STANDBY/ON  
button  
ON button  
3
O/Qbuttons  
6
INPUT buttons  
6
INPUT buttons  
6
Zoom ring  
Focus ring  
5
6
4
4
Adjustment  
buttons  
(P/R/O/Q)  
KEYSTONE button  
5
HEIGHT  
ADJUST lever  
4
P. 16  
_
1. Place the projector facing a wall or a screen  
2.Connect the projector to the computer and plug the power  
cord into the AC socket of the projector  
When connecting equipment other than a computer, see pages  
20 and 21.  
_PP. 19, 21  
3. Turn the projector on  
Press STANDBY/ON on the projector or ON on the remote control.  
_P. 23  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Adjust the projected image with the Setup Guide  
1 After the projector turns on, the Setup Guide appears.  
(When “Setup Guide” is set to “On”. See page 45.)  
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.  
3 After adjusting the focus, height (angle) and picture size, press ENTER to finish the  
Setup Guide.  
_P. 24  
5. Correct trapezoidal distortion  
Correcting trapezoidal distortion using Keystone Correction.  
Shrinks  
upper side.  
Shrinks  
lower side.  
On the remote control  
_P. 26  
6. Select the Input mode  
Press INPUT P/Rto display the INPUT list. Use INPUT P/Rto select the Input mode.  
On the  
projector  
On the remote  
control  
INPUT list  
INPUT  
Audio  
COMPUTER  
H
V
HDMI  
VIDEO  
When you select HDMI input, use O/Qto select the audio input terminal (HDMI or AUDIO).  
_P. 27  
7. Turn the computer on  
8. Turn the power off  
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press  
the button again while the confirmation message is displayed to put the projector into  
Standby mode.  
On-screen display  
On the  
projector  
On the remote  
control  
_P. 23  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector  
Video Setup  
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See  
page 42.)  
Setting Up the Projector  
For optimal image quality, position the projector perpendicular to the screen with the projector's  
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best  
image quality. (See page 26.)  
Standard Setup (Front Projection)  
■ Place the projector at the required distance from the screen according to the desired picture  
size. (See page 17.)  
Indication of the Projection Image Size and Projection Distance  
Example: 16:10 Signal Input (Normal Mode)  
Picture Size  
300" (762 cm)  
254"  
×
159"  
(646 cm  
200" (508 cm)  
×
404 cm)  
170"  
×
106"  
100" (254 cm)  
(431 cm  
85"  
×
×
269 cm)  
53"  
(215 cm  
×
40" (102 cm)  
135 cm)  
34"×  
(86 cm21"  
×
54 cm)  
Projection  
Distance  
4'4"–5'3"  
(1.3 m – 1.6 m)  
10'11"–13'2"  
(3.3 m – 4.0 m)  
21'10"–26'4"  
(6.7 m – 8.0 m)  
32'9"–39'6"  
(10.0 m – 12.0 m)  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Screen Size and Projection Distance  
Screen  
Note  
H
• Allow a margin of error in the values in the  
diagrams below.  
Lens center  
L
16:10 Signal Input (Normal Mode)  
Picture (Screen) size  
Projection distance [L]  
Distance from the lens center  
to the bottom of the image [H]  
χ
Diag. [ ]  
Width  
Height  
Minimum [L1]  
Maximum [L2]  
12.0 m (39' 6")  
10.0 m (32' 11")  
8.0 m (26' 4")  
6.0 m (19' 9")  
4.8 m (15' 10")  
4.0 m (13' 2")  
3.2 m (10' 6")  
2.4 m (7' 11")  
1.6 m (5' 3')  
300" (762 cm) 646 cm (254") 404 cm (159") 10.0 m (32' 9")  
7 cm (2 37/64")  
5 cm (2 9/64")  
4 cm (1 23/32")  
3 cm (1 9/32")  
3 cm (1 1/32")  
2 cm (0 55/64")  
2 cm (0 11/16")  
1 cm (0 33/64")  
1 cm (0 11/32")  
250" (635 cm) 538 cm (212") 337 cm (132")  
200" (508 cm) 431 cm (170") 269 cm (106")  
150" (381 cm) 323 cm (127") 202 cm (79")  
120" (305 cm) 258 cm (102") 162 cm (64")  
8.3 m (27' 4")  
6.7 m (21' 10")  
5.0 m (16' 5")  
4.0 m (13' 1")  
3.3 m (10' 11")  
2.7 m (8' 9")  
2.0 m (6' 7")  
1.3 m (4' 4")  
100" (254 cm) 215 cm (85")  
80" (203 cm) 172 cm (68")  
60" (152 cm) 129 cm (51")  
135 cm (53")  
108 cm (42")  
81 cm (32")  
54 cm (21")  
40" (102 cm)  
86 cm (34")  
4:3 Signal Input (Normal Mode)  
Picture (Screen) size  
Projection distance [L]  
Distance from the lens center  
to the bottom of the image [H]  
χ
Diag. [ ]  
Width  
Height  
Minimum [L1]  
Maximum [L2]  
300" (762 cm) 610 cm (240") 457 cm (180") 11.3 m (37' 1") 13.6 m (44' 9")  
7 cm (2 29/32")  
6 cm (2 27/64")  
5 cm (1 15/16")  
4 cm (1 29/64")  
3 cm (1 11/64")  
2 cm (0 31/32")  
2 cm (0 25/32")  
2 cm (0 43/64")  
1 cm (0 37/64")  
1 cm (0 25/64")  
250" (635 cm) 508 cm (200") 381 cm (150")  
200" (508 cm) 406 cm (160") 305 cm (120")  
150" (381 cm) 305 cm (120") 229 cm (90")  
9.4 m (30' 11") 11.4 m (37' 3")  
7.5 m (24' 9")  
5.7 m (18' 7")  
9.1 m (29' 10")  
6.8 m (22' 4")  
120" (305 cm) 244 cm (96")  
100" (254 cm) 203 cm (80")  
80" (203 cm) 163 cm (64")  
70" (178 cm) 142 cm (56")  
60" (152 cm) 122 cm (48")  
183 cm (72")  
152 cm (60")  
122 cm (48")  
107 cm (42")  
91 cm (36")  
61 cm (24")  
4.5 m (14' 10") 5.5 m (17' 11")  
3.8 m (12' 4")  
3.0 m (9' 11")  
2.6 m (8' 8")  
2.3 m (7' 5")  
1.5 m (4' 11")  
4.5 m (14' 11")  
3.6 m (11' 11")  
3.2 m (10' 5")  
2.7 m (8' 11")  
1.8 m (6' 0")  
40" (102 cm)  
81 cm (32")  
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.  
16:10 Signal  
[Feet/inches]  
4:3 Signal  
[m/cm] [Feet/inches]  
[m/cm]  
χ
χ
χ
χ
L1: Minimum projection distance (m/ft)  
0.03328 0.03328 / 0.3048 0.03768 0.03768 / 0.3048  
χ
χ
χ
χ
L2: Maximum projection distance (m/ft)  
0.04013 0.04013 / 0.3048 0.04543 0.04543 / 0.3048  
χ
χ
χ
χ
H: Distance from the lens center to the bottom of the image (cm/in) 0.02178  
0.02178 / 2.54  
0.02466  
0.02466 / 2.54  
χ
: Picture diagonal size : 40''-300''  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up the Projector (Continued)  
Projection (PRJ) Mode  
The projector can use any of the 4 projection modes shown in the diagram below. Select the  
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-  
ADJ” menu. See page 45.)  
■ Table mounted, front projection  
■ Ceiling mounted, front projection  
[Menu item ➞ “Front”]  
[Menu item ➞ “Ceiling + Front”]  
■ Ceiling mounted, rear projection  
(with a translucent screen)  
■ Table mounted, rear projection  
(with a translucent screen)  
[Menu item ➞ “Rear”]  
[Menu item ➞ “Ceiling + Rear”]  
a
Ceiling-Mount Setup  
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this  
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector  
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold  
separately).  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Projector to Other Equipment  
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet  
and turn off the equipment to be connected. After making all connections, turn on the projector  
and then the other pieces of equipment. When connecting a computer, ensure that it is the last  
equipment to be turned on after all the connections are made.  
IMPORTANT:  
Ensure that the appropriate input mode has been selected on the projector before  
you turn on the connected equipment.  
•
For more details of connection and cables, refer to the operation manual of the connecting equipment.  
• You may need other cables or connectors not listed below.  
Terminals on the Projector  
Terminal on  
connected equipment  
Terminal on the  
projector  
Equipment  
Computer  
Cable  
RGB cable (supplied)  
RGB  
output  
terminal  
COMPUTER/  
COMPONENT  
HDMI cable (commercially available)  
HDMI  
HDMI output  
terminal  
Note  
• Depending on specifications of equipment or the DVIÙHDMI digital cable, the signal transmission  
may not work property. (The HDMI specification does not support all connections to equipment that  
has digital output terminal using a DVIÙHDMI digital cable.)  
• See page 64 “Compatibility Chart” for a list of computer signals compatible with the projector. Use  
with computer signals other than those listed may cause some of the functions to not work.  
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest  
Macintosh Dealer.  
• Depending on the computer you are using, an image may not be projected unless the  
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys  
simultaneously when using a SHARP notebook computer). Refer to the specific instructions in  
your computer's operation manual to enable your computer's external output port.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting the Projector to Other Equipment (Continued)  
Terminal on  
Terminal on the  
projector  
Equipment  
Cable  
connected equipment  
Video equipment  
HDMI cable (commercially available)  
HDMI  
HDMI output  
terminal  
Component 3 RCA to mini D-sub 15 pin cable  
video output (optional, AN-C3CP2)  
terminal  
COMPUTER/  
COMPONENT  
Video output Video cable (commercially available)  
terminal  
VIDEO  
Camera/Video game  
Cables for a camera or a video game/3 RCA to COMPUTER/  
mini D-sub 15 pin cable (optional, AN-C3CP2) COMPONENT  
Component  
video  
output  
terminal  
RCA adaptor plug  
(commercially available)  
Cables for a camera or a video game  
VIDEO  
Video  
output  
terminal  
Note  
• Depending on specifications of equipment or the DVIÙHDMI digital cable, the signal transmission  
may not work property. (The HDMI specification does not support all connections to equipment that  
has digital output terminal using a DVIÙHDMI digital cable.)  
• HDMI (High-Definition Multimedia Interface) is a digital AV interface that can deliver a high-definition  
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.  
• Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the  
digital video signal does not degrade when transmitted, and a high-quality image with a simple  
connection can be enjoyed.  
• The HDMI terminal does not support the CEC signal.  
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a  
commercially available cable that fits in the projector terminal you want to connect.  
• The projector does not support RGBC signals via the Euro-scart.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Terminal on  
connected equipment  
Terminal on the  
projector  
Equipment  
Cable  
Audio equipment  
ø3.5 mm  
ø3.5 mm stereo minijack to RCA audio cable AUDIO  
audio output (commercially available)  
terminal  
RCA audio  
output  
RCA audio cable (commercially available)  
terminal  
Cables for a camera or a video game  
HDMI cable (commercially available)  
Audio  
output  
terminal  
HDMI  
HDMI output  
terminal  
Note  
• You can select HDMI or AUDIO in the INPUT list. (See page 27.)  
This projector is able to process the following signals when connected to HDMI  
equipment:  
• Video signal: For details, see “Digital Support” in the list of “Compatibility Chart” on page 64.  
• Audio signal: Linear PCM audio  
• Sampling frequency: 48kHz/44.1kHz/32kHz  
Connecting the Power Cord  
Plug the supplied power cord into the AC  
socket on the rear of the projector. Then  
plug into AC outlet.  
AC socket  
To AC outlet  
Power cord  
(supplied)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controlling the Projector by a Computer  
When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial  
control cable (cross type, commercially available), the computer can be used to control the  
projector and check the status of the projector. See page 59 for details.  
When connecting to a computer using an RS-232C serial control cable  
To RS-232C  
terminal  
To RS-232C  
terminal  
RS-232C serial control cable  
(cross type, commercially available)  
Computer  
Note  
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the  
operation manual of the computer for details.  
Info  
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This  
may damage your computer or projector.  
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.  
This may damage your computer.  
RS-232C Terminal: D-sub 9 pin male connector  
Pin No. Signal Name  
I/O  
Reference  
Not connected  
1
5
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
RD  
SD  
Receive Data  
Send Data  
Input  
Output  
Connected to internal circuit  
Connected to internal circuit  
Not connected  
Connected to internal circuit  
Not connected  
Connected to CS in internal circuit  
Connected to RS in internal circuit  
Not connected  
SG  
Signal Ground  
6
9
RS  
CS  
Request to Send  
Clear to Send  
RS-232C Cable recommended connection: D-sub 9 pin female connector  
Pin No. Signal  
Pin No. Signal  
5
1
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
CD  
RD  
SD  
ER  
SG  
DR  
RS  
CS  
CI  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
CD  
RD  
SD  
ER  
SG  
DR  
RS  
CS  
CI  
9
6
Projector  
Pin No.  
Computer  
Pin No.  
Note  
4
5
6
4
5
6
• Depending on the controlling device used, it may be necessary to  
connect Pin 4 and Pin 6 on the controlling device (e.g. computer).  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the Projector On/Off  
Info  
Turning the Projector On  
• When “Auto Restart” is set to “On”:  
If the power cord is unplugged from the outlet  
or the breaker switch is turned off when the  
projector is on, then the projector  
automatically turns on when the power cord  
is plugged into the AC outlet or the breaker  
switch is turned on. (See page 46.)  
• English is the factory default language. If you  
want to change the on-screen display to  
another language, change the language  
according to the procedure on page 45.  
Note that the connections to external  
equipment and power outlet should be  
done before performing the operations  
written below. (See pages 19 to 21.)  
Press STANDBY/ON on the projector  
or ON on the remote control.  
• The power indicator illuminates green.  
• After the lamp indicator illuminates, the projector  
is ready to start operation.  
Power indicator  
Lamp indicator  
Note  
STANDBY/ON button  
• About the Lamp Indicator  
The lamp indicator illuminates to indicate the  
status of the lamp.  
Green: The lamp is on.  
Blinking in green: The lamp is warming up.  
Red: The lamp is shut down  
abnormally or the lamp should be  
replaced.  
• When switching on the projector, a slight  
flickering of the image may be experienced  
within the first minute after the lamp has been  
illuminated. This is normal operation as the  
lamp's control circuitry is stabilising the lamp  
output characteristics. It should not be  
regarded as faulty operation.  
• If the projector is put into Standby mode and  
immediately turned on again, the lamp may  
take some time to start projection.  
• When System Lock is set, the keycode input  
box appears. To cancel the keycode setting,  
input the keycode that you have already set.  
See page 47 for details.  
STANDBY  
button  
ON button  
On-screen display (confirmation message)  
Turning the Power Off (Putting  
the Projector into Standby Mode)  
Press STANDBY/ON on the projector  
or STANDBY on the remote control,  
then press that button again while the  
confirmation message is displayed, to  
Info  
put the projector into Standby mode.  
• Direct Power Off function:  
You can unplug the power cord from the AC  
outlet even if the cooling fan is still running.  
• The projector cannot be turned on while cooling.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection  
About the Setup Guide  
ENTER button  
Focus ring  
After turning on the projector, the Setup  
Guide screen appears to assist you with  
projector setup.  
Guidance items  
1 FOCUS  
2 HEIGHT ADJUST  
3 ZOOM  
Press ENTER to exit the Setup Guide  
screen.  
Note  
• The Setup Guide screen automatically  
highlights the items in the following order:  
1 FOCUS 2 HEIGHT ADJUST  
4 ENTER  
3 ZOOM  
However, you can adjust the focus, height  
(angle) or zoom regardless of the highlighted  
item.  
• If you do not want to display the Setup Guide  
for the next time, set “Menu” - “SCR-ADJ” -  
“Setup Guide” to “Off”. (See page 45.)  
Adjusting the Projected Image  
1 Adjusting the Focus  
You can adjust the focus with the focus  
ring on the projector.  
Rotate the focus ring to adjust the  
focus while watching the projected  
image.  
• Using the knob on the focus ring will make the  
adjustments easier.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2 Adjusting the Height  
The height of the projector can be  
adjusted using the adjustment feet at the  
front and rear of the projector.  
When the screen is above the projector,  
the projection image can be made higher  
by adjusting the projector.  
Lift the projector to adjust its  
height while lifting the HEIGHT  
ADJUST lever.  
1
Make small  
adjustments.  
HEIGHT ADJUST lever  
Remove your hands from the  
2
HEIGHT ADJUST lever of the  
projector after its height has  
been finely adjusted.  
• The angle of projection is adjustable up to  
9 degrees from the surface on which the  
projector is placed.  
Rear adjustment foot  
Use the rear adjustment foot to  
make the projector level.  
• The projector is adjustable 2 degrees  
from the standard position.  
3
Info  
• Do not apply too much pressure on the  
projector when the front adjustment foot  
comes out.  
Note  
•
When lowering the projector, be careful not to  
get your fingers caught in the area between  
the adjustment foot and the projector.  
• When adjusting the height of the projector,  
trapezoidal distortion occurs. Follow the  
procedures in Keystone Correction to correct  
the distortion. (See pages 26 and 43.)  
•
Hold the projector firmly while lifting or carrying.  
• Do not hold by the lens area.  
3 Adjusting the Picture Size  
You can adjust the picture size using the  
zoom ring on the projector.  
Zoom ring  
Rotate the zoom ring to enlarge or  
shrink the picture size.  
• Using the knob on the zoom ring will make the  
adjustments easier.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Correcting Trapezoidal  
Distortion  
Adjustment buttons  
When the image is projected either from  
the top or from the bottom towards the  
screen at an angle, the image becomes  
distorted trapezoidally. The function for  
correcting trapezoidal distortion is called  
Keystone Correction.  
(P/R/O/Q)  
Note  
RETURN button  
•
The Keystone Correction can be adjusted up to  
an angle of approximately 40 degrees and the  
screen can also be set up to an angle of  
KEYSTONE button  
approximately 40 degrees (When the Resize  
mode is set to “NORMAL” (see page 28))  
.
On-screen display  
(Keystone Correction mode)  
Press KEYSTONE to enter the  
Keystone Correction mode.  
1
KEYSTONE  
ADJUST  
0
END  
Shrinks upper side.  
(Move the slide bar in the + direction.)  
Press P/Qor O/Rto adjust the  
Keystone Correction.  
2
Shrinks lower side.  
(Move the slide bar in the - direction.)  
Note  
• To return to the default setting, press  
RETURN while the on-screen display of the  
Keystone Correction mode is on the screen.  
Press KEYSTONE.  
3
• The on-screen display of the Keystone  
Correction mode will disappear.  
Info  
• While adjusting the image using Keystone  
Correction, straight lines and the edges of the  
image may appear jagged.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VOL +/– (Volume)  
buttons  
Switching the Input Mode  
Select the appropriate Input mode for the  
connected equipment.  
INPUT buttons  
Press INPUT P/Rto display the  
INPUT list.  
AV MUTE button  
Use INPUT P/Rto select the Input  
mode.  
O/Qbuttons  
When you select HDMI input, use O/Q  
to select the audio input terminal  
(HDMI or AUDIO).  
Adjusting the Volume  
Press VOL +/– on the remote control  
or –O/Q+ on the projector to adjust  
the volume.  
On-screen display  
Note  
• Pressing VOL–/–Owill lower the volume.  
• Pressing VOL+/Q+ will raise the volume.  
Displaying the Black Screen  
and Turning Off the Sound  
Temporarily  
Press AV MUTE on the remote control  
to temporarily display a black screen  
and turn off the sound.  
On-screen display  
Note  
• Pressing AV MUTE again will turn the  
projected image back on.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Projection (Continued)  
Resize Mode  
This function allows you to modify or customize the Resize mode to enhance the input  
image. Depending on the input signal, you can choose a desired image.  
Press RESIZE.  
• See page 43 for setting on menu screen.  
RESIZE  
button  
COMPUTER  
NORMAL  
FULL  
1280 × 800  
—
NATIVE  
800 × 600  
1024 × 768  
1152 × 864  
1400 × 1050  
1280 × 1024  
—
16:9  
SVGA (800 × 600)  
XGA (1024 × 768)  
4:3 aspect ratio  
1068 × 800  
SXGA (1152 × 864)  
1280 × 720  
SXGA+ (1400 × 1050)  
SXGA (1280 × 1024)  
1280 × 720  
1000 × 800  
1280 × 720  
1280 × 722  
1280 × 720  
1280 × 768  
1280 × 800  
1360 × 768  
Other aspect ratios  
1360 × 768  
1366 × 768  
—
1366 × 768  
1280 × 768  
1280 × 800  
—
1280 × 720  
Input signal  
Computer  
Output screen image  
FULL NATIVE  
Image type  
NORMAL  
16:9  
Resolution XGA and below  
*1  
*3  
Resolution higher than  
XGA  
4:3 aspect ratio  
*1  
SXGA (1280 × 1024)  
1280 × 720  
5:4 aspect ratio  
16:9 aspect ratio  
16:9 aspect ratio  
15:9 aspect ratio  
16:10 aspect ratio  
—
*2  
*1  
*1  
—*2  
1360 × 768  
1366 × 768  
*1  
*1  
1280 × 768  
1280 × 800  
—*2  
—*2  
: Cutout area on which images cannot be projected  
: Area where the signals are off screen  
*1 The Image Shift function can be used for these images.  
*2 Same as NORMAL mode.  
*3 In case SXGA+ input.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO/DTV  
Input signal  
Output screen image  
AREA ZOOM V-STRETCH  
Video/DTV  
Image type  
NORMAL  
16:9  
*1  
*1  
*1  
4:3 aspect ratio  
Squeeze  
480I, 480P,  
576I, 576P,  
NTSC, PAL,  
SECAM  
Letter box  
*1  
*1  
*1  
*1  
16:9 aspect ratio  
16:9 aspect ratio  
16:9 aspect ratio  
720P, 1035I,  
1080I, 1080P  
—*2  
540P  
16:9 aspect ratio  
(4:3 aspect ratio in 16:9)  
: Cutout area on which images cannot be projected  
: Area on which the image is not included in the original signals  
*1 The Image Shift function can be used for these images.  
*2 Same as NORMAL mode.  
About Copyrights  
• When using the Resize function to select an image size with a different aspect ratio to a TV  
program or video image, the image will look different from its original appearance. Keep this  
in mind while choosing an image size.  
• The use of the Resize or Keystone Correction function to compress or stretch the image for  
commercial purposes/public displays in a café, hotel, etc. may be an infringement of  
copyright protected by law for copyright holders. Please use caution.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating with the Remote Control  
MAGNIFY buttons  
Displaying the Pointer  
FREEZE button  
PICTURE MODE button  
Press POINTER and press P/R/  
1
O/Qon the remote control to  
AUTO SYNC button  
move the pointer.  
• Press EFFECT to change the pointer icon  
(5 types).  
BREAK TIMER button  
SPOT button  
Star  
Finger1  
Finger2  
Heart  
Underline  
Adjustment buttons  
(P/R/O/Q)  
EFFECT button  
Press POINTER again.  
2
ECO+QUIET button  
POINTER button  
• The pointer will disappear.  
Using the Spot Function  
Displaying and Setting the  
Break Timer  
Press SPOT and press P/R/O/Q  
1
on the remote control to move  
the spot area.  
Press BREAK TIMER.  
1
• Press EFFECT to change the spot area  
size (3 types).  
• The timer starts to count down from 5  
minutes.  
1/9  
1/25  
1/8  
On-screen display  
Press P/R/O/Qto adjust the  
2
Press SPOT again.  
2
length of the break time.  
• The spot area will disappear.  
•Increases with Por Q  
5 minutes ➞ 6 minutes ➞ 60 minutes  
•Shortens with Oor R  
4 minutes ➞ 3 minutes ➞1 minute  
• The break time can be set in units of one  
minute (up to 60 minutes).  
Switching the Eco+Quiet  
Mode  
Canceling the break timer display function  
Press ECO+QUIET to switch the  
Press BREAK TIMER.  
Eco+Quiet mode between on and off.  
• When the Eco+Quiet Mode is set to “ON”, the  
sound of the cooling fan will turn down, the power  
consumption will decrease, and the lamp life will  
extend.  
Note  
• The Break Timer is not available while the  
projector is operating the following functions.  
- Auto Sync  
- Freeze  
- AV Mute  
Note  
• Refer to “Eco+Quiet” on page 40 for details.  
- Input Search  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Auto Sync  
(Auto Sync Adjustment)  
Displaying an Enlarged  
Portion of an Image  
Auto Sync function works when detecting Graphs, tables and other portions of  
input signal after the projector turns on.  
projected images can be enlarged. This  
is helpful when providing more detailed  
explanations.  
Press AUTO SYNC to manually adjust  
with Auto Sync function.  
Press  
MAGNIFY on the  
1
remote control.  
Note  
• Enlarges the image.  
• When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual  
adjustments. (See page 41.)  
• Pressing  
or reduces the projected image.  
or  
MAGNIFY enlarges  
Note  
Press  
.
×1 ×2 ×3 ×4  
Freezing a Moving Image  
Press  
.
Press FREEZE.  
1
• You can change the location of the  
enlarged image using P, R, Oand Q.  
• The projected image is frozen.  
Press FREEZE again to return to  
the moving image from the  
currently connected device.  
2
Press RETURN on the remote  
2
control to cancel the operation.  
• The magnification then returns to ×1.  
Note  
• The selectable magnifications differ  
depending on the input signal.  
• In the following cases, the image will  
return to the normal size (×1).  
- When switching the Input mode.  
- When RETURN has been pressed.  
- When the input signal is changed.  
- When the input signal resolution and  
refresh rate (vertical frequency)  
change.  
Selecting the Picture Mode  
You can select the appropriate Picture  
mode for the projected image, such as  
movie or video game.  
Press PICTURE MODE.  
• When pressing PICTURE MODE, the Picture  
mode changes in the following order:  
- When the Resize mode is changed.  
STANDARD  
PRESENTATION  
MOVIE GAME sRGB  
*
Note  
• See page 38 for details on the Picture mode.  
*
“sRGB” is displayed only when RGB signal is input.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items  
The following shows the items that can be set in the projector.  
“Quick Start Menu”  
“Picture” menu  
Main menu  
Sub menu  
Main menu  
Sub menu  
Standard  
Presentation  
Movie  
Game  
sRGB  
Picture  
Picture Mode  
Quick Start Menu  
Input Search Start  
Page 36  
Resolution  
Page 38  
Page 38  
Page 36  
Contrast  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
Resize  
Normal  
Full  
Bright  
Color  
Tint  
Native  
Area Zoom  
V-Stretch  
Border  
16:9  
Page 36  
Keystone  
-80 +80  
Sharp  
Red  
Page 36  
Eco + Quiet [On/Off]  
Blue  
Page 39  
Page 36  
Language  
English  
polski  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Magyar  
Türkçe  
Page 36  
CLR Temp  
-1  
0
1
2
Tiếng Việt  
Page 39  
BrilliantColor™  
Page 39  
C.M.S. Setting [On/Off]  
Page 39  
C.M.S.  
Svenska  
Português  
Information  
Page 36  
Go To Complete Menu  
Page 36  
Page 39  
Film Mode  
Auto  
Off  
Page 40  
DNR  
Level 1  
Level 2  
Level 3  
Page 40  
Eco+Quiet [On/Off]  
Page 40  
Reset  
C.M.S.-Hue  
R
Y
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
-30 +30  
Page 39  
C.M.S.-Saturation  
G
C
Page 39  
C.M.S.-Value  
B
M
Page 39  
Reset  
Reset  
Return  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
“Signal adjustment (SIG-ADJ)” menu  
“Screen adjustment (SCR-ADJ)” menu  
Main menu  
SIG-ADJ  
Sub menu  
Main menu  
SCR - ADJ  
Sub menu  
Resize  
Clock  
Phase  
H-Pos  
V-Pos  
Reset  
-150 +150  
-30 +30  
-150 +150  
-60 +60  
Normal  
Full  
Page 43  
Page 43  
Page 41  
Native  
Area Zoom  
V-Stretch  
Border  
16:9  
Image Shift  
-40 +40  
Page 43  
Page 41  
Keystone  
-80 +80  
Resolution  
Page 43  
Page 41  
Signal Type  
Overscan [On/Off]  
Auto  
RGB  
Page 44  
YPbPr  
Page 41  
Dynamic Range  
Page 41  
OSD Display [On/Off]  
Auto  
Standard  
Enhanced  
Page 44  
Closed Caption  
Off  
CC1  
CC2  
Page 44  
Video System  
Auto  
PAL  
Background  
Logo  
Blue  
None  
SECAM  
NTSC4.43  
NTSC3.58  
PAL-M  
PAL-N  
Page 42  
Page 45  
Setup Guide [On/Off]  
PAL-60  
Page 45  
Video Setup  
0 IRE  
7.5 IRE  
PRJ Mode  
Front  
Ceiling + Front  
Rear  
Ceiling + Rear  
Page 42  
Signal Info  
Page 45  
Page 42  
Wall Color  
Off  
Blackboard  
Whiteboard  
Page 45  
English  
polski  
Language  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Magyar  
Türkçe  
Page 45  
Tiếng Việt  
Svenska  
Português  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Items (Continued)  
“Projector adjustment (PRJ-ADJ1/2)” menu  
Main menu  
PRJ-ADJ1  
Sub menu  
Auto Sync [On/Off]  
Page 46  
Page 46  
Auto Power Off [On/Off]  
Page 46  
Auto Restart [On/Off]  
Page 46  
Speaker [On/Off]  
Page 46  
Fan Mode  
Normal  
High  
Page 46  
System Lock  
[Enable/Disable]  
Page 47  
Keylock [On/Off]  
Page 48  
Main menu  
PRJ-ADJ2  
Sub menu  
Quick Start Menu [On/Off]  
Page 46  
Page 49  
FUNCTION Button  
Input Search  
Audio Mute  
Image Shift  
Signal Info  
Page 49  
STANDBY Mode  
Quick Start  
Eco  
Page 49  
DLP® LinkTM [On/Off]  
Page 49  
DLP® LinkTM Invert  
Page 49  
All Reset  
Page 49  
Lamp Timer (Life)  
Page 49  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen  
Select from the Quick Start Menu, which is a collection of the most frequently used  
functions, or the Complete Menu, which enables advanced settings and adjustments.  
Adjustment buttons (P/R/O/Q)  
ENTER button  
MENU button  
MENU button  
ENTER button  
Adjustment buttons  
(P/R/O/Q)  
RETURN button  
• Press RETURN to return  
to the previous screen  
when the menu is  
displayed.  
Menu Selections (Quick Start Menu)  
• This operation can also be performed by using the buttons on the projector.  
Example  
Press MENU.  
1
• The “Quick Start Menu” screen for the  
selected Input mode is displayed.  
Quick Start Menu  
1024×768  
Input Search Start  
Resolution  
Normal  
Resize  
Press Por Rto select the  
2
3
Keystone  
Eco+Quiet  
Language  
Information  
0
desired item, then press ENTER.  
Off  
English  
Press P/R/O/Qto adjust the  
item selected, then press  
ENTER.  
Go To Complete Menu…  
Info  
SEL./ADJ.  
ENTER  
END  
• To display the advanced settings and  
adjustments, select “Go To Complete Menu”.  
Press ENTER to display the Complete Menu  
screen.  
•
If you do not want to display the Quick Start  
Menu, set “Go To Complete Menu” - “PRJ-ADJ2”  
- “Quick Start Menu” to “Off”. (See page 49.)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Menu Screen (Continued)  
Quick Start Menu  
The following items can be configured on the Quick Start Menu.  
Selectable items  
Input Search Start  
Description  
Automatically searches for and switches to the appropriate Input mode.  
Pressing an operation button during input searching cancels the search.  
Resolution  
Resize  
Manually change the resolution.  
Use this function when the image and screen size do not match with the  
resolution selected automatically. (See page 41.)  
Changes the Resize mode.  
Use this function to stretch the image vertically or horizontally or when the  
edges of the image cannot be seen. (See page 43.)  
Keystone  
Eco+Quiet  
Corrects the keystone distortion of projected images.  
Use this function to correct the trapezoidal distortion of images caused when  
projecting images at an angle to the screen. (See page 43.)  
When set to “On”, this function reduces the cooling fan noise and power  
consumption, thereby prolonging the operating life of the lamp. (See page 40.)  
Language  
Selects the language displayed on the screen. (See page 45.)  
Displays the input signal, lamp use time, remaining lamp life, etc.  
Displays the Complete Menu for advanced settings and adjustments.  
Information  
Go To Complete Menu  
Note  
• The setting of Resize mode will be made independently for each Input mode.  
• The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture  
mode.  
Menu Selections (Complete Menu)  
Example: Adjusting “Bright”.  
• This operation can also be performed by using the buttons on the projector.  
Press MENU.  
Example: “Picture” screen menu for  
COMPUTER (RGB) input  
1
• The “Quick Start Menu” screen is  
displayed.  
Menu item  
Picture  
SIG  
SCR  
PRJ1  
PRJ2  
Press Por Rto select “Go To  
2
3
Picture Mode  
Contrast  
Bright  
Standard  
Complete Menu”.  
0
0
0
0
0
1
Red  
Press Qor Oand select  
“Picture” to adjust.  
Blue  
CLR Temp  
BrilliantColorTM  
C.M.S. Setting  
C.M.S.  
DNR  
Eco+Quiet  
Reset  
On  
Info  
Level 2  
Off  
• When “PRJ-ADJ2” - “Quick Start Menu” is  
set to “On”, pressing MENU displays the  
Quick Start Menu screen.  
SEL./ADJ.  
ENTER  
END  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Press Por Rand select “Bright”  
Picture  
SIG  
SCR  
PRJ1  
PRJ2  
4
to adjust.  
Picture Mode  
Contrast  
Bright  
Standard  
• The selected item is highlighted.  
0
0
0
0
0
1
Red  
Blue  
CLR Temp  
BrilliantColorTM  
C.M.S. Setting  
C.M.S.  
On  
DNR  
Eco+Quiet  
Reset  
Level 2  
Off  
SEL./ADJ.  
Single ADJ  
END  
Items to be adjusted  
PRJ1  
PRJ2  
SIG  
Pict.  
SCR-ADJ  
Resize  
Normal  
To adjust the projected  
image while watching it  
Image Shift  
Keystone  
0
0
Press ENTER.  
• The selected item (e.g. “Bright”) is  
displayed by itself at the bottom of the  
screen.  
Press ENTER.  
• When pressing Por R, the following item  
(“Red” after “Bright”) will be displayed.  
The item displayed by itself  
Picture  
Bright  
0
Note  
SEL./ADJ.  
Rtn. Menu  
END  
• Press ENTER again to return to the  
previous screen.  
Picture  
SIG  
SCR  
PRJ1  
PRJ2  
Press Oor Qto adjust the item  
5
6
Picture Mode  
Contrast  
Bright  
Standard  
selected.  
0
1 5  
0
• The adjustment is stored.  
Red  
Blue  
CLR Temp  
BrilliantColorTM  
0
0
1
On  
C.M.S. Setting  
C.M.S.  
DNR  
Eco+Quiet  
Reset  
Level 2  
Off  
Press MENU.  
• The menu screen will disappear.  
SEL./ADJ.  
Single ADJ  
END  
Note  
• The MENU button is not available while the projector is operating:  
- Auto Sync/Break Timer/Freeze/AV Mute/Input Search  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu)  
Menu operation n Page 36  
Q PAGE1  
Q PAGE2  
Picture  
SIG  
SCR  
PRJ1  
PRJ2  
Picture  
SIG  
SCR  
PRJ1  
PRJ2  
1
Picture Mode  
Contrast  
Bright  
Color  
Standard  
Picture Mode  
Standard  
0
0
0
0
0
0
0
0
1
CLR Temp  
3
2
BrilliantColorTM  
C.M.S. Setting  
C.M.S.  
Tint  
On  
2
4
Sharp  
Red  
5
6
7
Film Mode  
DNR  
Auto  
Level 2  
Off  
Blue  
Eco+Quiet  
Reset  
SEL./ADJ.  
ENTER  
END  
SEL./ADJ.  
ENTER  
END  
Selecting the Picture Mode  
1
The default settings of each item when selecting Picture Mode  
Selectable  
items  
Description  
CLR Temp  
BrilliantColorTM  
Eco+Quiet  
Off  
Standard  
For standard image  
0
0
1
2
Presentation Brightens portions of image for  
more enhanced presentations.  
Off  
Movie  
Game  
*sRGB  
Gives natural tint to the  
projected image.  
–1  
0
0
1
–
On  
Off  
Off  
Gives sharpness to the  
projected image.  
For high fidelity reproduction of  
images from a computer.  
–
• “sRGB” is displayed only when RGB signal is input.  
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are  
retained in memory.  
Note  
•
You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 31.)  
• *sRGB is an international standard of color reproduction regulated by the IEC (International  
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are  
displayed in a natural tint based on an original image, when “sRGB” is selected.  
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColorTM” and “C.M.S.”, when “sRGB” is  
selected.  
Info  
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a  
malfunction.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 36  
Adjusting the Image  
Adjusting the Colors  
2
4
This function adjusts each of the six main  
colors that comprise the color wheel, altering  
their “Hue”, “Saturation”, or “Value”.  
Adjustment  
items  
Contrast  
Obutton  
Qbutton  
For less  
contrast.  
For less  
brightness.  
For less color  
intensity.  
For making skin For making skin  
tones purplish.  
For less  
sharpness.  
For weaker red. For stronger  
red.  
For weaker  
blue.  
For more  
contrast.  
For more  
brightness.  
For more color  
intensity.  
Selectable items  
Description  
Bright  
Color*1  
Tint*1  
C.M.S.-Hue  
Sets the hue of the main colors.  
C.M.S.-Saturation Sets the saturation of the main  
colors  
C.M.S.-Value  
Sets the brightness of the main  
colors.  
tones greenish.  
For more  
sharpness.  
Sharp*1  
Red*2  
Reset  
The adjustments of “Hue”,  
“Saturation” and “Value” of all  
colors are reset to the default  
setting.  
Blue*2  
For stronger  
blue.  
Return  
Returns to the “Picture” menu  
screen.  
BrilliantColor™*2 *3 For making the For making the  
effect weaker.  
effect stronger.  
Adjusting “Hue”, “Saturation”, or “Value”.  
*1 Not displayed in the RGB input mode.  
*2 Not adjustable/selectable when selecting “sRGB”.  
*3 BrilliantColor™ uses Texas Instruments'  
BrilliantColor™ technology. As the BrilliantColor™  
level is increased, the image becomes brighter  
while the color reproduction is kept at a high level.  
1 Select “On” for “C.M.S. Setting” in the “Picture”  
menu and then press ENTER.  
2 Select “C.M.S.” in the “Picture” menu and then  
press ENTER.  
3 Press Por Rto select either “Hue”, “Saturation”, or  
“Value” and then press ENTER.  
Note  
4 Select the color to be adjusted with Por Rand  
adjust it with Oor Q.  
• To reset all adjustment items, select “Reset”  
and press ENTER.  
Example of adjusting the “Hue”  
Main colors  
R (Red)  
Obutton  
Qbutton  
Closer to magenta Closer to yellow  
Adjusting the Color  
Temperature  
3
Y (Yellow)  
G (Green)  
C (Cyan)  
B (Blue)  
Closer to red  
Closer to green  
Closer to cyan  
Closer to blue  
Closer to magenta  
Closer to red  
Closer to yellow  
Closer to green  
Closer to cyan  
Selectable  
items  
Description  
For lower color temperature for  
warmer, reddish incandescent-like  
images.  
M (Magenta) Closer to blue  
–1  
0
• When “Saturation” is selected, the selected  
color becomes  
O: lighter. Q: thicker.  
• When “Value” is selected, the selected color  
becomes  
1
For higher color temperature for  
cooler, bluish, fluorescent-like images.  
O: darker. Q: brighter.  
• To reset the adjustment values of each color to  
the default settings, select “Reset” and press  
ENTER.  
Note  
• Values on “CLR Temp” are only for general  
standard purposes.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Adjustment (“Picture” Menu)  
(Continued)  
Menu operation n Page 36  
Selecting the Film Mode  
Eco+Quiet  
5
7
This function provides high-quality playback  
of images originally projected at 24 fps, such  
as movies on DVDs.  
Selectable  
items  
Brightness and Power consumption  
On  
Off  
Approx. 75%  
100%  
Selectable  
Description  
items  
Auto  
Off  
Films are detected automatically.  
Films are not detected.  
Note  
• When “Eco+Quiet” is set to “On”, the fan  
sound and power consumption are lower than  
they are when “Off” is selected. (Projection  
brightness decreases as shown in the chart.)  
Note  
• This function is available for the following  
signals.  
With COMPUTER/COMPONENT input:  
- 480I  
- 576I  
- 1035I  
- 1080I  
With VIDEO input:  
- All signals  
Reducing Image Noise (DNR)  
6
Video digital noise reduction (DNR) provides  
high quality images with minimal dot crawl  
and cross color noise.  
Selectable  
Description  
items  
Level 1  
Sets the DNR level for viewing a  
clearer picture.  
Level 2  
Level 3  
Note  
• This function is not available for some signals.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Signal Adjustment (“SIG-ADJ” Menu)  
Menu operation n Page 36  
Pict.  
SIG-ADJ  
SCR  
PRJ1  
PRJ2  
Clock  
Phase  
H-Pos  
V-Pos  
0
0
0
0
1
Reset  
Resolution  
Signal Type  
Dynamic Range  
Video System  
Video Setup  
2
3
4
5
6
1024 x 768  
Auto  
Standard  
Auto  
0 IRE  
Signal Info 1024 x 768  
48.3 kHz 60.0 Hz  
7
H
/
V
SEL./ADJ.  
ENTER  
END  
Adjusting the Computer Image  
Signal Type Setting  
1
3
If the optimum image cannot be obtained with  
Auto Sync adjustment, use the SIG-ADJ function.  
This function allows you to select the input  
signal type RGB or Component for  
COMPUTER/COMPONENT.  
Selectable  
Description  
items  
Selectable  
Description  
items  
Clock  
Phase  
Adjusts vertical noise.  
Auto  
Input signals are automatically  
recognized as RGB or component.  
Adjusts horizontal noise (similar to  
tracking on your VCR).  
RGB  
Set when RGB signals are received.  
H-Pos  
V-Pos  
Centers the on-screen image by  
moving it to the left or right.  
YPbPr  
Set when Component signals are  
received.  
Centers the on-screen image by  
moving it up or down.  
Selecting the Dynamic Range  
4
Note  
An optimum picture may not be displayed if an  
HDMI-capable device’s output signal type and  
the projector’s input signal type do not match. If  
this should occur, switch “Dynamic Range”.  
• To reset all adjustment items, select “Reset”  
and press ENTER.  
• The adjustable range of “H-Pos” (H-Position)  
and “V-Pos” (V-Position) may vary depending  
on the screen resolution of the computer.  
Selectable  
Description  
items  
Auto  
In most circumstances, “Auto” should  
be selected.  
Resolution Setting  
2
Standard  
Enhanced  
When the black levels of the image  
show banding or appear faded, select  
the item that results in the best picture  
quality.  
Ordinarily, the type of input signal is detected and  
the correct Resolution mode is automatically  
selected. However, for some signals, the optimal  
Resolution mode in “Resolution” may need to be  
selected to match the computer display mode.  
Note  
Note  
• The Dynamic Range can be selected only  
when “HDMI” input mode is selected.  
• See “Checking the Input Signal” on page 42  
for information on the currently selected input  
signal.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Signal Adjustment (“SIG-ADJ” Menu)  
(Continued)  
Menu operation n Page 36  
Setting the Video System  
Setting the Video Setup  
5
6
The video input system mode is factory preset  
to “Auto”; however, a clear picture from the  
connected audio-visual equipment may not be  
received, depending on the Video signal  
difference.  
Selectable  
items  
Description  
0 IRE  
Sets the black level to 0 IRE.  
Sets the black level to 7.5 IRE.  
7.5 IRE  
In that case, switch the Video signal.  
Selectable items  
Auto  
Note  
• This function is available for the following  
signals.  
PAL  
With COMPUTER/COMPONENT input:  
- 480I  
SECAM  
*NTSC4.43  
NTSC3.58  
PAL-M  
With VIDEO input:  
- NTSC3.58  
PAL-N  
Checking the Input Signal  
7
PAL-60  
This function allows you to check the current  
input signal information.  
* When reproducing NTSC signals in PAL  
video equipment.  
Note  
• The Video signal can only be set in VIDEO  
mode.  
• When “Video System” is set to “Auto”, you  
may not receive a clear picture due to signal  
differences. Should this occur, switch to the  
video system of the source signal.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image (“SCR-ADJ” Menu)  
Menu operation n Page 36  
Pict.  
SIG  
SCR-ADJ PRJ1  
PRJ2  
Resize  
Normal  
1
2
3
4
5
6
7
8
9
0
Image Shift  
Keystone  
Overscan  
OSD Display  
Closed Caption  
Background  
Setup Guide  
PRJ Mode  
0
0
On  
On  
Off  
Logo  
On  
Front  
Off  
Wall Color  
Language  
English  
SEL./ADJ.  
ENTER  
END  
Setting the Resize Mode  
Keystone Correction  
1
3
Use this function to stretch the image  
vertically or horizontally or when the edges of  
the image cannot be seen.  
When the image is projected either from the top  
or from the bottom towards the screen at an  
angle, the image becomes distorted trapezoidally.  
The function for correcting trapezoidal distortion  
is called Keystone Correction.  
Note  
Select “Keystone” on the “SCR-ADJ”  
menu and adjust with the slide bar.  
See page 26 for details of Keystone Correction.  
• For details of the Resize mode, see pages  
28 and 29.  
• You can also press RESIZE on the remote  
control to set the Resize mode. (See page 28.)  
Qbutton  
Obutton  
Adjusting the Image  
Position  
2
You can move the projected image vertically.  
Note  
•
The Keystone Correction can be adjusted up to  
an angle of approximately 40 degrees (When  
the Resize mode is set to “NORMAL”).  
• You can also press KEYSTONE on the  
remote control to adjust Keystone Correction.  
Obutton  
Qbutton  
Note  
• This function only works in some Resize  
modes. (See pages 28 and 29.)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projected Image (“SCR-ADJ” Menu)  
(Continued)  
Menu operation n Page 36  
Setting the Overscan  
Closed Caption  
4
6
This function allows you to set the overscan area  
(display area).  
<For Americas only>  
Info  
Selectable  
Description  
items  
• This function is available for NTSC3.58 signal.  
• This function does not work when the Resize  
mode is set to “Border”.  
• This function is available in the following cases  
only:  
On  
The input area is displayed without the  
screen edges.  
Off  
The whole input area is displayed.  
Resize mode  
Keystone Correction  
-40 − +40  
Normal  
Area Zoom  
V-Stretch  
Note  
• This function is available for the following  
signals.  
16:9  
-12 − +12  
With COMPUTER/COMPONENT or HDMI*  
input:  
- 480P  
- 540P  
- 576P  
- 720P  
• “Closed Caption” is a system which allows  
conversations, narration, and sound effects in TV  
programs (Limited regions) and home videos to  
be viewed as captions on the screen.  
- 1035I  
- 1080I/1080P  
• If noise appears at the screen edges when  
“Off” is selected, set the function to “On”.  
• Also see “About Copyrights” on page 29.  
• Not all programs and videos will offer closed  
captioning. Please look for the  
symbol to  
ensure that captions will be shown.  
• Two channels are available: CC1 and CC2.  
Selectable  
Description  
items  
Off  
—
Setting the On-screen  
Display  
5
CC1  
CC2  
Closed Caption mode for CH1 data  
Closed Caption mode for CH2 data  
Selectable  
items  
Description  
Note  
On  
Off  
All on-screen displays are displayed.  
•
Closed Caption may malfunction (white blocks,  
strange characters, etc.) if signal conditions are  
poor or if there are problems at the broadcast  
source. This does not necessarily indicate a  
problem with the projector.  
• If any button is pressed to call up the on-  
screen display while viewing a Closed Caption  
broadcast, the closed captions will disappear.  
VOLUME/AV MUTE/FREEZE/AUTO  
SYNC/RESIZE/PICTURE MODE/  
ECO+QUIET/MAGNIFY/Input Search/  
Audio Mute/“An invalid button has  
been pressed.” are not displayed.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 36  
Selecting the Background  
Image  
7
Selecting the Wall Color  
This function allows you to project the image  
to a colored (white or dark green) surface or  
wall without using a screen.  
0
Selectable items  
Description  
Sharp logo screen  
Logo  
Blue  
Selectable items  
Description  
Blue screen  
—
Off  
The Wall Color function is not  
activated.  
None  
Blackboard  
Whiteboard  
Projects images onto a  
blackboard (dark green).  
Selecting the Setup Guide  
8
Projects images onto a  
whiteboard.  
Selectable items  
Description  
On  
Displaying the Setup Guide  
when turning the projector on.  
Selecting the On-screen  
Display Language  
Off  
Not displaying the Setup Guide.  
The projector can switch the on-screen  
display language among 18 languages.  
Reversing/Inverting  
Projected Images  
9
English  
polski  
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Magyar  
Türkçe  
Selectable items  
Description  
Front  
Normal image (Projected from  
the front of the screen)  
Tiếng Việt  
Ceiling + Front  
Rear  
Inverted image (Projected from  
the front of the screen with an  
inverted projector)  
Svenska  
Português  
Reversed image (Projected from  
the rear of the screen or with a  
mirror)  
Ceiling + Rear  
Reversed and inverted image  
(Projected with a mirror)  
See page 18 for details of Projection (PRJ) Mode.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)  
Menu operation n Page 36  
Q PRJ-ADJ1  
Q PRJ-ADJ2  
Pict.  
SIG  
SCR  
PRJ1 PRJ-ADJ2  
On  
Pict.  
SIG  
SCR PRJ-ADJ1 PRJ2  
8
Quick Start Menu  
1
2
3
4
Auto Sync  
On  
On  
On  
On  
Auto Power Off  
Auto Restart  
Speaker  
9
0
FUNCTION Button  
STANDBY Mode  
Input Search  
Quick Start  
5
6
7
Fan Mode  
System Lock  
Keylock  
Normal  
Disable  
Off  
DLP® Link TM  
DLP® Link TM Invert  
All Reset  
Off  
Lamp Timer(Life)  
SEL./ADJ.  
0
h
0
min 100%  
END  
ENTER  
SEL./ADJ.  
ENTER  
END  
Auto Sync (Auto Sync  
Adjustment)  
1
Auto Restart Function  
3
Selectable  
items  
Description  
Selectable  
items  
Description  
On  
If the power cord is unplugged from the  
outlet or the breaker switch is turned off  
when the projector is on, then the  
projector automatically turns on when  
the power cord is plugged into the AC  
outlet or the breaker switch is turned on.  
On  
Auto Sync adjustment will occur when  
the projector is turned on or when the  
input signals are switched, when  
connected to a computer.  
Off  
Auto Sync adjustment is not  
automatically performed.  
Off  
The projector does not turn on  
automatically when the power cord is  
plugged into the AC outlet or the  
breaker switch is turned on.  
Note  
• Auto Sync adjustment is also performed by  
pressing AUTO SYNC.  
• The Auto Sync adjustment may take some  
time to complete, depending on the image of  
the computer connected to the projector.  
• When the optimum image cannot be achieved  
with Auto Sync adjustment, use manual  
adjustments. (See page 41.)  
Speaker Setting  
4
Selectable  
items  
Description  
On  
The audio signal is output from the  
internal speaker.  
Off  
The audio signal is not output from the  
internal speaker.  
Auto Power Off Function  
2
Selectable  
items  
Description  
Fan Mode Setting  
This function changes the fan rotation speed.  
5
On  
Off  
When no input signal is detected for  
more than 15 minutes, the projector will  
automatically enter Standby mode.  
Selectable  
Description  
items  
The Auto Power Off function will be  
disabled.  
Normal  
High  
Suitable for normal environments.  
Set when using the projector at  
altitudes of approximately 1,500 meters  
(4,900 feet) or more.  
Note  
• When the Auto Power Off function is set to  
“On”, 5 minutes before the projector enters  
Standby mode, the message “Enter STANDBY  
mode in X min.” will appear on the screen to  
indicate the remaining minutes.  
When “Fan Mode” is set to “High”, the fan rotation  
speeds up, and the fan noise becomes louder.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 36  
Press the 4 buttons on the remote  
control or on the projector to enter  
the new keycode in “New Code”.  
System Lock Function  
4
6
This function prevents unauthorized use of the  
projector. Once this function is activated,  
users must enter the correct keycode each  
time the projector is turned on. We suggest  
you record the keycode in a safe place  
where only authorized users have access.  
Note  
• You cannot use the following buttons  
for keycode: STANDBY/ON, ON,  
STANDBY, ENTER, RETURN and  
MENU  
Info  
•
System Lock function recognizes  
each button on the remote control  
or on the projector as an individual  
button, even if they share the same  
button name. If you used the buttons  
on the projector in setting your  
keycode, the keycode cannot be  
canceled with the remote control.  
• If you lose or forget your keycode, contact  
your nearest Sharp Authorized Projector  
Dealer or Service Center (see page 69). Even  
if the product warranty is valid, the keycode  
reset will incur a charge.  
a
Setting/Changing the Keycode  
Select “System Lock”, then press  
PRJ - ADJ1  
Setting the System Lock  
1
ENTER or Q.  
Old Code  
New Code  
Reconfirm  
* * * *  
–
–
–
–
–
–
–
–
Select “Next”, then press ENTER.  
• The screen for entering the keycode  
appears.  
2
Enter the same keycode in “Re-  
confirm”.  
5
Press the 4 buttons on the remote  
control or on the projector to enter  
the preset keycode in “Old Code”.  
• When setting the keycode for the first time,  
press Ron the projector for four times.  
3
Note  
To cancel the keycode that you have  
already set  
PRJ - ADJ1  
• Press Ron the projector for four times in  
steps 4 and 5 above.  
When the System Lock is set  
• When System Lock is set, the keycode input  
screen appears after the power is turned on.  
When it appears, enter the right keycode to  
start projection.  
Setting the System Lock  
–
–
–
–
–
–
–
–
–
–
–
–
Old Code  
New Code  
Reconfirm  
Note  
Input screen for keycode  
•
If you input a wrong keycode, the cursor returns to  
the first point of the “Old Code”.  
• The preset keycode is 4 Rbuttons on the  
projector. When you press the Rbutton four  
times, the keycode input screen disappears.  
– – – –  
System Lock  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)  
(Continued)  
Menu operation n Page 36  
Taking the Keylock Off  
Hold down ENTER on the projector for about  
5 seconds.  
Keylock Function  
7
Use this function to lock the operation buttons  
on the projector.  
This function can be set using either the menu  
screen or ENTER on the projector.  
On-screen display  
a
Setting with the menu screen  
Selectable  
items  
Description  
Info  
On  
All buttons on the projector, except  
STANDBY/ON, are locked.  
• Even when Keylock function is set to “On”,  
STANDBY/ON on the projector can be used  
to turn on and off the power.  
Off  
Turns off the Keylock function.  
• Keylock cannot be set while the projector is:  
displaying the “Setup Guide” or “Menu”  
screens, in Standby mode, warming up,  
changing input signals, operating the Auto  
Sync or Input Search function, in Freeze  
mode or on the “System Lock” screen during  
warming up.  
a
Setting with the projector buttons  
Locking the Operation Buttons  
Hold down ENTER on the  
1
projector for about 5 seconds  
while the projector is being  
turned on.  
• The Keylock function screen is displayed.  
PRJ - ADJ1  
Use this function to lock the operation buttons  
on the projector.  
(Except STANDBY/ON button)  
Note: You can release the keylock by holding  
down ENTER on the projector for about 5 seconds.  
Return  
On  
SEL.  
ENTER  
END  
Select “On”, then press ENTER  
.
2
On-screen display  
• The Keylock function does not affect the  
operation with the remote control buttons.  
• You cannot use the Keylock function while the  
projector is warming up.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu operation n Page 36  
Selecting the Quick  
Start Menu  
Returning to the Default  
Settings  
8
This function allows you to initialize the  
settings you have made in the projector.  
Selectable items  
Description  
On  
Pressing MENU displays the  
Quick Start Menu screen.  
Note  
Off  
Pressing MENU displays the  
Complete Menu screen.  
• The following items or menu cannot be  
initialized.  
- Resolution  
- Language  
- Lamp Timer (Life)  
- System Lock  
Setting the FUNCTION  
Button Operation  
You can assign one of the following functions  
to the FUNCTION button on the remote con-  
trol. The assigned function can be performed  
by just pressing FUNCTION.  
9
Checking the Lamp  
Life Status  
Selectable items  
Description  
You can confirm the cumulative lamp usage  
time and the remaining lamp life (percentage).  
Input Search  
Automatically searches for and  
switches to the appropriate Input  
mode.  
Lamp usage condition  
Remaining lamp life  
Audio Mute  
For temporarily turning off the  
sound. Press FUNCTION again  
to turn on the sound  
“Life”  
100%  
Approx.  
5%  
Operated exclusively  
with “Eco+Quiet”  
set to “On”  
Approx.  
Image Shift  
Signal Info  
For moving the projected image  
vertically. (See page 43.)  
5,000 hours 250 hours  
Input signal information is displayed.  
Operated exclusively  
with “Eco+Quiet”  
set to “Off”  
Approx.  
Approx.  
3,000 hours 150 hours  
STANDBY Mode  
0
Selectable  
items  
Description  
Note  
• It is recommended that the lamp be changed  
when the remaining lamp life becomes 5%.  
• The lamp life may vary depending on the  
usage condition.  
Eco  
Power consumption is reduced in  
Standby mode.  
Quick Start The period of startup time is reduced.  
DLP® LinkTM  
See “Using 3D Viewing Mode” on page 52 for  
details.  
DLP® LinkTM Invert  
See “Using 3D Viewing Mode” on page 52 for  
details.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Stereoscopic 3D Images  
Precautions on Viewing Stereoscopic 3D Images  
Before viewing stereoscopic 3D images, please read this section carefully.  
WARNING  
■
Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would  
normally view your screen. However, some people may experience discomfort. The following  
precautions are recommended to minimize the potential for experiencing visual problems or any  
adverse symptoms.  
■
■
Take regular breaks, at least 5 to 15 minutes after every 30 to 60 minutes of stereoscopic 3D  
viewing.  
* Based on the guidelines issued by the 3D Consortium revised December 10, 2008.  
Maintain an appropriate distance from the screen. Viewing from too close a distance can strain  
your eyes. If you experience eye strain, immediately discontinue viewing.  
If you experience any of the following symptoms during viewing:  
• nausea, queasiness/dizziness, headache, blurry vision or double vision that lasts longer than few  
seconds  
Do not engage in any potentially hazardous activity (for example, driving a vehicle) until your  
symptoms have completely gone away. If symptoms persist, discontinue use and do not resume  
stereoscopic 3D viewing without discussing your symptoms with a physician.  
• As you get more comfortable viewing stereoscopic 3D:  
• Adjust the parallax on the 3D-video playback equipment. (You may not be able to adjust the  
parallax on some models of equipment.)  
• Adjust the projected image to the most comfortable viewing size by zooming.  
(Projecting images on the smallest or largest screen size possible may eliminate the stereoscopic  
effect and strain your eyes.)  
• Use the DLP® Link™ Invert function to properly set the video for your left and right eyes. (For  
details on using “DLP® Link™ Invert”, see the section on its operation in this operation manual.)  
The following people should limit stereoscopic 3D viewing:  
– Children under 6 years of age (to protect the eye growth process)  
– People with a history of photosensitivity  
– People with heart disease  
■
– People in poor health  
– People who are sleep deprived  
– People who are physically tired  
– People under the influence of drugs or alcohol  
■
Epilepsy  
A small percentage of the population may experience epileptic seizures when viewing certain  
types of images that contain flashing patterns of light.  
IF YOU OR ANY MEMBER OF YOUR FAMILY HAS A HISTORY OF EPILEPSY  
The following people should consult a physician before viewing stereoscopic 3D images.  
– Anyone with a history of epilepsy, or who has a family member with a history of epilepsy  
– Children under 6 years of age  
– Anyone who has ever experienced epileptic seizures or sensory disturbances triggered by  
flashing light effects  
SOME LIGHT PATTERNS MAY INDUCE SEIZURES IN PERSONS WITH NO PRIOR  
HISTORY OF EPILEPSY  
Discontinue use if you experience any of the following symptoms while viewing stereoscopic  
3D images.  
– Involuntary movements, eye or muscle twitching  
– Muscle cramps  
– Nausea, dizziness, or queasiness  
– Convulsions  
– Disorientation, confusion, or loss of awareness of your surroundings  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Information on the 3D Projection Function  
•
To display 3D images, this projector requires:  
WHAT YOU WILL NEED  
1) Source devices that support the field sequential format  
– For details on the supported signals, see the Compatibility Chart in this operation manual.  
2) 3D LCD shutter glasses that support the DLP® Link™* system  
– Contact your nearest Sharp Authorized Projector Dealer for purchasing details.  
* DLP® Link™ is a trademark of Texas Instruments.  
•
•
The projected image may become dark when using the 3D projection function (with “DLP® Link™ ”  
set to “On”).  
When “DLP® Link™” is set to “On”, the following functions may not work fully or may not be  
available at all.  
– Keystone/Resize/Magnify  
•
•
3D formats except for the field sequential method, such as ones used for Blu-ray 3D or DVD  
prepackaged media, are not compatible with this projector. (As of March 2012)  
If the power of your left and right eyes greatly differs and you primarily use one eye for viewing the  
images, the images will not appear in 3D.  
In addition, images may be difficult to view in 3D or images may not be able to be viewed in 3D  
depending on the individual or the content being displayed.  
The stereoscopic effect varies with the individual.  
•
3D viewing is possible within the range that the 3D LCD shutter glasses are able to receive light  
signals reflected by the screen. However, most 3D images are manufactured to be viewed from  
directly in front of the screen, so 3D viewing is recommended directly in front of the screen as  
much as possible.  
– The range for receiving signals varies depending on the 3D LCD shutter glasses. For details, see  
the operation manual of your 3D LCD shutter glasses.  
•
3D images may not be able to be played back correctly on your computer.  
Appendix  
■
How the 3D Projection Function (DLP Link™ ) Works  
The 3D projection function of this projector is compatible with the DLP® Link™ system. To watch  
3D images, you use a pair of 3D LCD shutter glasses that alternately display the projected images  
for the left and right eyes and are synchronized with a control (light) signal.  
Shutter glasses  
control light signal*  
* The control light signal is transmitted from the lens of the projector, reflected by the screen, and  
received by the light reception sensor on the 3D LCD shutter glasses. Therefore, the range of 3D  
viewing varies depending on the specifications of the 3D LCD shutter glasses (light signal  
receiving sensitivity).  
For details, see the operation manual of your 3D LCD shutter glasses.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Stereoscopic 3D Images (Continued)  
Press 3D MODE on the remote  
6
control to display the 3D MODE  
Using 3D Viewing Mode  
menu.  
Info  
Use the following procedure to project  
3D images.  
• If “An invalid button has been pressed.”  
is displayed, a 3D-compatible signal is  
not being input. Check the output signal  
on the playback equipment.  
For operation of the 3D LCD shutter  
glasses and the 3D-video playback  
equipment, see the corresponding  
operation manual.  
Press Qto set “DLP® Link™” to  
“On”.  
7
8
ENTER button  
O/Qbuttons  
Press ENTER to switch the mode  
and enable more natural 3D  
image viewing.  
Warning!  
If the projector, 3D-video playback  
equipment, and 3D LCD shutter  
•
3D MODE button  
glasses are not properly set, you may  
experience eye strain in addition to not  
being able to view the images in 3D.  
Projecting 3D images  
Turn the projector on.  
1
Press 3D MODE.  
9
• The 3D MODE menu will disappear.  
Turn the 3D-video playback  
2
equipment on.  
• Set the 3D-video playback equipment so  
that it outputs one of the signals listed in  
the Compatibility Chart in this operation  
manual.  
Note  
• If the images are not displayed in 3D, repeat  
steps 6 to 8.  
• You can also use “DLP® Link™” and “DLP®  
Link™ Invert” on the menu screen to change  
the 3D setting.  
Switch the Input mode of the  
projector to enable input of 3D  
video signals.  
3
Ending 3D projection  
Operate the 3D-video playback  
equipment and play back the 3D  
content.  
Press 3D MODE on the remote  
control to display the 3D MODE  
menu.  
4
1
Press Oto set “DLP® Link™” to  
“Off”.  
Turn the 3D LCD shutter glasses  
on and place them over your eyes.  
5
2
Press 3D MODE.  
3
• The 3D MODE menu will disappear.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance  
Cleaning the projector  
■ Ensure that you have unplugged the power  
cord before cleaning the projector.  
■ The cabinet as well as the operation panel is  
made of plastic. Avoid using benzene or  
thinner, as these can damage the finish on  
the cabinet.  
■ Do not use volatile agents such as  
insecticides on the projector.  
Cleaning the lens  
■ Use a commercially available blower or lens  
cleaning paper (for glasses and camera  
lenses) for cleaning the lens. Do not use any  
liquid type cleaning agents, as they may  
wear off the coating film on the surface of the  
lens.  
■ As the surface of the lens can easily get  
damaged, be careful not to scrape or hit the  
lens.  
Do not attach rubber or plastic items to the  
projector for long periods.  
The effects of some of the agents in the  
plastic may cause damage to the quality or  
finish of the projector.  
Caution  
• Do not use any glass cleaner to clean the lens.  
• Avoid touching the lens with your hands to  
prevent fingerprints on or damage to the lens  
surface.  
■ Wipe off dirt gently with a soft flannel cloth.  
Using a chemical cloth (wet/dry sheet type  
cloth, etc.) may deform the components of  
the cabinet or cause cracking.  
■ Wiping with a hard cloth or using strong  
force may scratch the cabinet surface.  
■ When the dirt is hard to remove, soak a cloth  
in a mild detergent diluted with water, wring  
the cloth well and then wipe the projector.  
Strong cleaning detergents may discolor,  
warp or damage the coating on the projector.  
Make sure to test on a small, inconspicuous  
area on the projector before use.  
Cleaning the exhaust and intake vents  
■ Use a vacuum cleaner to clean dust from the  
exhaust vent and the intake vent.  
Mild detergent diluted  
with water  
Info  
• If you want to clean the air vents during  
projector operation, ensure you press  
STANDBY/ON on the projector or  
Thinner  
Wax  
STANDBY on the remote control and put the  
projector into Standby mode. After the  
cooling fan has stopped, clean the vents.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance Indicators  
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the  
projector indicate problems inside the projector.  
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will  
illuminate red, and the projector will enter Standby mode. After the projector has entered  
Standby mode, follow the procedures given below.  
Temperature warning indicator  
Lamp indicator  
Top View  
Power indicator  
About the temperature warning indicator  
If the temperature inside the projector increases, due to blockage of the air vents, or the setting  
location, the temperature warning indicator will blink. And if the temperature keeps on rising,  
“
” will illuminate in the lower left corner of the picture with the temperature warning  
indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then  
the projector will enter Standby mode. When you find the temperature warning indicator  
blinking, be sure to perform the measures described on page 55.  
About the lamp indicator  
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will  
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the  
lamp will automatically turn off and then the projector will automatically enter Standby mode.  
At this time, the lamp indicator will illuminate in red.  
■ If you try to turn on the projector a fourth time without replacing the lamp, the  
projector will not turn on.  
Indicators on the Projector  
Power indicator  
Red on  
Normal (Standby)  
Normal (Power on)  
Abnormal (See page 55.)  
Normal (Cooling)  
Normal  
The lamp is warming up.  
The lamp is shut down abnormally or requires to be  
changed. (See page 55.)  
Green on  
Red blinks  
Green blinks  
Green on  
Green blinks  
Red on  
Lamp indicator  
Temperature  
warning indicator  
Off  
Normal  
Red on/Red blinks The internal temperature is abnormally high. (See page 55.)  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Maintenance indicator  
Problem  
Cause  
Possible Solution  
Normal  
Abnormal  
Temperature  
warning  
indicator  
Off  
Red blinks The internal  
• Temperatures  
around the projector  
are high.  
• Use the projector in an  
area with a temperature of  
lower than 95°F (+35ºC).  
• Relocate the projector to  
an area with proper  
(On)/  
Red on  
temperature is  
abnormally high.  
(Standby)  
• Blocked air intake  
ventilation. (See page 8.)  
• Cooling fan  
breakdown  
• Internal circuit failure  
• Clogged air intake  
• Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 69) for  
repair.  
Lamp  
indicator  
Green on  
(Green  
blinks  
when the  
lamp is  
warming  
up.)  
Red on  
Red on  
The lamp does  
not illuminate.  
• The lamp is shut  
down abnormally.  
• Disconnect the power cord  
from the AC outlet, and  
then connect it again.  
Time to change  
the lamp.  
• Remaining lamp life  
becomes 5% or less.  
• Carefully replace the lamp.  
(See page 56.)  
• Take the projector to your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 69) for  
repair.  
The lamp does  
• Burnt-out lamp  
• Lamp circuit failure  
(Standby) not illuminate.  
• Please exercise care when  
replacing the lamp.  
• Securely install the cover.  
Power  
indicator  
Green on/ Red blinks The power  
• The lamp unit cover • If the power indicator blinks  
Red on  
Green  
blinks  
indicator blinks in  
red when the  
projector is on.  
is open.  
in red even when the lamp  
unit cover are securely  
installed, contact your  
nearest Sharp Authorized  
Projector Dealer or Service  
Center (see page 69) for  
advice.  
(Cooling)  
Info  
• If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the  
possible solutions above and then wait until the projector has cooled down completely before  
plugging in the power cord and turning the power back on. (At least 10 minutes.)  
• If the power is turned off for a brief moment due to power outage or some other cause while using  
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate  
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace  
the power cord in the AC outlet and then turn the power on again.  
• The cooling fan keeps the internal temperature of the projector constant and this function is  
controlled automatically. The sound of the cooling fan may change during operation because the fan  
speed may change and this is not a malfunction.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp  
Lamp  
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes  
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life  
(percentage) can be checked with the on-screen display. (See page 49.)  
■ Purchase a replacement lamp of type AN-LX20LP from your place of purchase, nearest Sharp  
Authorized Projector Dealer or Service Center.  
IMPORTANT NOTE TO U.S. CUSTOMERS:  
The lamp included with this projector is backed by a 90-day parts and labor limited  
warranty. All service of this projector under warranty, including lamp replacement,  
must be obtained through a Sharp Authorized Projector Dealer or Service Center.  
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,  
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).  
Hg LAMP CONTAINS MERCURY For State Lamp Disposal  
Information  
www.lamprecycle.org or 1-800-BE-SHARP  
U.S.A ONLY  
Caution Concerning the Lamp  
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure  
can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches  
or deterioration of the lamp due to a lapse of usage time.  
The period of time up to failure largely varies depending on the individual lamp and/or the condition and  
the frequency of use. It is important to note that failure can often result in the bulb cracking.  
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended  
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating  
normally.  
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.  
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or  
Service Center to assure safe operation.  
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the  
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes  
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of  
exposure to the gas, consult a doctor as soon as possible.  
Replacing the Lamp  
Caution  
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause  
burns or injury.  
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully  
cool before removing the lamp unit.  
■ Carefully change the lamp by following the instructions described in this section.  
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector  
Dealer or Service Center.  
*
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector  
Dealer or Service Center for repair.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Removing and Installing the  
Lamp Unit  
Warning!  
• Do not remove the lamp unit from the  
projector right after use. The lamp and parts  
around the lamp will be very hot and may  
cause burns or injury.  
Optional  
accessory  
Lamp unit  
AN-LX20LP  
Info  
• Do not touch the glass surface of the lamp  
unit or the inside of the projector.  
• To avoid injury to yourself and damage to the  
lamp, make sure you carefully follow the  
steps below.  
• Do not loosen other screws except for the  
lamp unit cover and lamp unit.  
STANDBY/ON button  
Press STANDBY/ON on the  
1
projector or STANDBY on the  
remote control to put the  
projector into Standby mode.  
Disconnect the power cord.  
2
• Unplug the power cord from the AC  
socket.  
• Leave the lamp until it has fully cooled  
down (about 1 hour).  
AC socket  
Remove the lamp unit cover.  
3
• Loosen the user service screw (1) that  
secures the lamp unit cover. Slide the lamp  
unit cover in the direction of the arrow and  
then lift it up (2).  
User service screw  
(for lamp unit cover)  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Regarding the Lamp (Continued)  
Remove the lamp unit.  
4
Securing  
screw  
• Loosen the securing screw from the lamp  
unit. Hold the lamp unit and pull it in the  
direction of the arrow. At this time, keep  
the lamp unit horizontal and do not tilt it.  
Insert the new lamp unit.  
5
6
•
Press the lamp unit firmly into the lamp unit  
compartment to align the lamp connectors.  
Fasten the securing screw.  
Replace the lamp unit cover.  
• Slide the lamp unit cover horizontally back  
into place and align the tabs (1). Then  
tighten the user service screw (2) to  
secure the lamp unit cover.  
Info  
• If the lamp unit and lamp unit cover  
are not correctly installed, the power  
will not turn on, even if the power  
cord is connected to the projector.  
Resetting the Lamp Timer  
Reset the lamp timer after replacing the lamp.  
Info  
• Make sure to reset the lamp timer only when  
replacing the lamp. If you reset the lamp timer  
and continue to use the same lamp, this may  
cause the lamp to become damaged or  
explode.  
Connect the power cord.  
1
AC socket  
• Plug the power cord into the AC socket of  
the projector.  
STANDBY/ON  
button  
Reset the lamp timer.  
ENTER button  
2
• While simultaneously holding down  
MENU, ENTER and Ron the projector,  
press STANDBY/ON on the projector and  
keep all four buttons pressed down until  
the lamp indicator starts blinking green.  
• “LAMP 0000H” is displayed, indicating  
that the lamp timer is reset.  
MENU button  
Rbutton  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands  
Computer control  
A computer can be used to control the projector by connecting an RS-232C serial  
control cable (cross type, commercially available) to the projector. (See page 22.)  
Communication conditions  
Set the serial port settings of the computer to match that of the table.  
Signal format: Conforms to RS-232C standard.  
Baud rate: 9,600 bps  
Data length: 8 bits  
Parity bit: None  
Stop bit: 1 bit  
Flow control: None  
Basic format  
Commands from the computer are sent in the following order: command,  
parameter, and return code. After the projector processes the command from the  
computer, it sends a response code to the computer.  
Command format  
C1  
C2  
C3  
C4  
P1  
P2  
P3  
P4  
Return code (0DH)  
Command 4-digit  
Parameter 4-digit  
Response code format  
Normal response  
Problem response (communication error or incorrect command)  
O
K
E
R
R
Return code (0DH)  
Return code (0DH)  
Info  
• When controlling the projector using RS-232C commands from a computer, wait for at least 30  
seconds after the power has been turned on, and then transmit the commands.  
• After sending an input selection or picture adjustment command and then receiving an “OK” response  
code, the projector may take some time to process the command. If a second command is sent while  
the projector is still processing the first command, you may receive an “ERR” response code. If this  
happens, try resending the second command.  
• When more than one code is being sent, send each command only after the response code for the  
previous command from the projector is verified.  
• “POWR????”, “TABN _ _ _ 1”, “TLPS _ _ _ 1”, “TPOW _ _ _ 1”, “TLPN _ _ _ 1”, “TLTT _ _ _ 1”,  
“TLTM _ _ _ 1”, “TLTL _ _ _ 1”, “TNAM _ _ _ 1”, “MNRD _ _ _ 1”, “PJN0 _ _ _ 1”  
− When the projector receives the special commands shown above:  
* The on-screen display will not disappear.  
* The “Auto Power Off” timer will not be reset.  
− The special commands are available for applications that require continuous polling.  
Note  
• If an underbar (_) appears in the parameter column, enter a space.  
• If an asterisk (*) appears in the parameter column, enter a value in the range indicated in brackets  
under Control Contents.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands  
(Continued)  
Commands  
Example: When turning on the projector, make the following setting.  
Computer  
Projector  
→
←
P
O
W
R
_
_
_
1
O
K
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
(or 30-second startup time)  
_
_
_
_
_
_
Power  
On  
P
P
P
T
O
O
O
A
W
W
W
B
R
R
R
N
1
0
?
1
OK or ERR  
OK  
Off  
OK  
1
0: Normal  
1: Temp High  
8: Lamp Life 5% or less  
16: Lamp Burn-out  
OK or ERR  
0
0: Normal  
1: Temp High  
2: Fan Error  
4: Cover Open  
Status  
?
_
?
_
?
_
Projector Condition  
32: Lamp Ignition Failure 8: Lamp Life 5% or less  
16: Lamp Burn-out  
32: Lamp Ignition Failure  
64: Temp Abnormally High  
_
_
_
Status  
T
L
P
S
1
0: Off, 1: On, 2: Retry  
0: Off, 4: Lamp Error  
0: Standby  
Lamp  
3: Waiting, 4: Lamp Error  
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
_
_
_
_
_
_
_
*
Power Status  
Quantity  
T
T
T
T
T
T
M
P
P
L
L
L
L
N
N
J
O
P
T
T
T
A
R
N
W
N
T
M
L
M
D
1
1
1
1
1
1
1
1
*
1: On, 2: Cooling  
1
Usage Time(Hour)  
0 – 9999(Integer)  
0, 15, 30, 45  
0% – 100%(Integer)  
PGLW2000  
Usage Time(Minute)  
Life(Percentage)  
Name  
Model Name Check  
Model Name Check  
PG-LW2000  
OK or ERR  
Projector Name Setting 1  
(First 4 characters) *1  
P
P
J
J
N
N
2
3
*
*
*
*
*
*
*
*
OK or ERR  
OK or ERR  
Projector Name Setting 2  
(Middle 4 characters) *1  
Projector Name Setting 3  
(Last 4 characters) *1  
_
_
_
_
?
_
_
_
_
?
_
_
_
_
?
Projector Name Check  
COMPUTER  
HDMI  
P
I
I
I
I
J
R
R
V
R
N
G
G
E
0
B
B
D
B
1
1
2
1
?
Projector Name  
OK or ERR  
Input Change  
ERR  
ERR  
ERR  
ERR  
OK or ERR  
VIDEO  
Input RGB Check  
OK or ERR  
1: COMPUTER  
2: HDMI, ERR  
G
Input Video Check  
Input Mode Check  
Input Check  
I
I
I
V
M
C
E
O
H
D
D
K
?
?
?
?
?
?
?
?
?
?
?
?
1: VIDEO, ERR  
ERR  
ERR  
ERR  
1: RGB, 2: VIDEO  
1: COMPUTER,  
2: HDMI, 3: VIDEO  
_
_
_
*
*
Volume  
Volume(0 – 60)  
V
V
K
I
I
F
O
O
E
L
U
Y
B
B
E
E
J
S
S
S
S
S
S
S
S
S
S
S
S
S
S
A
D
S
K
K
Z
*
*
*
*
*
*
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
Volume up/down(-10 – +10)  
Keystone  
AV Mute  
-80 – +80  
On  
*
_
_
_
M
M
R
R
D
A
A
A
A
A
A
A
B
B
B
B
B
B
B
1
0
1
0
1
1
2
3
5
6
0
1
1
2
3
5
6
0
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off  
Freeze  
On  
Off  
F
Z
Auto Sync  
Resize  
Start  
COMPUTER  
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
S
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Normal  
16:9  
Native  
Full  
Border  
Area Zoom  
V-Stretch  
Normal  
16:9  
1
1
_
_
_
_
_
HDMI  
Native  
Full  
Border  
Area Zoom  
V-Stretch  
1
1
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Resize  
VIDEO  
Normal  
16:9  
R
R
R
R
R
A
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
A
A
A
A
A
L
S
S
S
S
S
R
P
P
P
P
P
P
B
R
B
C
T
V
V
V
V
V
E
S
S
S
S
S
I
R
D
E
O
I
H
T
E
M
M
R
R
R
E
I
1
2
3
0
1
1
0
1
2
3
4
*
*
*
*
*
*
*
*
*
ERR  
ERR  
ERR  
ERR  
ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
Border  
Area Zoom  
V-Stretch  
1
1
_
All Reset  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
COMPUTER Input  
Picture Mode  
Standard  
Presentation  
Movie  
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
M
M
M
1
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
_
_
_
Game  
sRGB  
Contrast  
Bright  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
Red  
Blue  
Color  
Tint  
Sharp  
S
C
W
F
*
_
CLR Temp  
BrilliantColor™  
Film Mode  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0 – +2  
Auto  
0
1
1
2
3
1
Off  
F
DNR  
Level 1  
N
N
N
R
S
S
S
P
P
P
P
P
P
B
R
B
C
T
Level 2  
Level 3  
Picture Reset  
Signal Type  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Auto  
0
1
2
0
1
2
3
4
*
*
*
*
*
RGB  
I
I
I
I
YPbPr  
HDMI Input  
Picture Mode  
Standard  
Presentation  
Movie  
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
I
S
S
S
S
S
I
R
D
E
O
I
H
T
E
R
R
R
E
I
1
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
Game  
sRGB  
Contrast  
Bright  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
Red  
Blue  
Color  
Tint  
*
*
*
Sharp  
S
C
W
N
N
N
R
S
S
S
A
A
B
B
B
*
_
CLR Temp  
BrilliantColor™  
DNR  
_
_
_
_
0 – +2  
Level 1  
Level 2  
*
1
2
3
Level 3  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Picture Reset  
Signal Type  
1
0
1
2
1
2
0
1
2
Auto  
RGB  
I
I
I
I
I
I
YPbPr  
AUDIO  
HDMI  
Audio Input  
R
R
H
H
H
Dynamic Range Auto  
D
D
D
Standard  
Enhanced  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RS-232C Specifications and Commands  
(Continued)  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
VIDEO Input  
Picture Mode  
Standard  
Presentation  
Movie  
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
I
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
P
P
P
P
P
B
R
B
C
T
S
S
S
S
I
R
D
E
O
I
1
1
1
1
*
*
*
*
*
*
*
*
_
_
_
_
_
_
_
0
1
2
3
*
*
*
*
*
*
*
*
*
0
1
1
2
3
1
1
0
*
*
*
*
*
*
2
*
*
*
*
*
*
3
*
*
*
*
*
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
Game  
Contrast  
Bright  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-30 – +30  
-1 – +1  
*
*
*
*
*
*
Red  
Blue  
Color  
Tint  
Sharp  
S
C
W
F
H
T
*
_
CLR Temp  
BrilliantColor™  
Film Mode  
_
_
_
_
_
_
_
_
_
0 – +2  
E
M
M
R
R
R
E
S
S
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
R
Y
G
C
B
M
E
E
L
Auto  
Off  
F
DNR  
Level 1  
N
N
N
R
C
C
H
H
H
H
H
H
R
S
S
S
S
S
S
R
V
Level 2  
Level 3  
A
Picture Reset  
A
C.M.S. Setting  
C.M.S.  
On  
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
N
N
A
1
0
*
*
*
*
*
*
_
Off  
Hue  
Red  
*
*
*
*
*
Yellow  
Green  
Cyan  
Blue  
Magenta  
Reset  
Red  
*
_
Saturation  
*
*
*
*
*
*
*
*
*
*
Yellow  
Green  
Cyan  
Blue  
Magenta  
Reset  
Red  
*
_
*
_
Value  
*
*
*
*
*
*
_
_
*
*
*
*
*
*
_
_
Yellow  
Green  
Cyan  
V
V
V
V
Blue  
Magenta  
Reset  
V
*
R
R
C
P
H
V
4
1
*
*
*
C.M.S. All Reset  
-150 – +150  
-30 – +30  
Clock  
*
_
*
*
*
*
*
*
Phase  
I
I
I
I
H
P
P
E
S
N
N
I
H-position  
V-position  
-150 – +150  
-60 – +60  
*
_
A
A
N
V
V
M
M
E
*
*
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Fine Sync Adjustment Reset  
Image Shift  
Overscan  
R
D
S
S
D
D
S
S
S
S
S
S
S
S
B
B
B
M
M
1
*
-40 – +40  
On  
L
*
_
*
_
O
O
I
1
0
1
0
1
2
3
4
5
6
7
8
1
3
4
1
0
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off  
OSD Display  
Video System  
On  
Off  
I
I
Auto  
M
M
M
M
M
M
M
M
I
Y
Y
Y
Y
Y
Y
Y
Y
G
G
G
D
D
PAL  
E
E
E
E
E
E
E
M
M
M
H
H
SECAM  
NTSC4.43  
NTSC3.58  
PAL-M  
PAL-N  
PAL-60  
Logo  
Blue  
Background  
Eco+Quiet  
I
I
None  
On  
T
T
Off  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RETURN  
CONTROL CONTENTS  
COMMAND  
PARAMETER  
Standby mode  
Power ON  
OK or ERR  
(or 30-second startup time)  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
ERR  
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Auto Sync  
On  
A
A
A
A
A
A
M
M
I
A
A
P
P
R
R
O
O
M
M
M
M
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
S
S
F
F
L
L
S
I
I
L
L
L
S
S
D
D
D
L
D
D
O
O
E
E
U
U
R
R
I
I
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
J
J
1
0
1
0
1
0
1
0
1
0
1
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
1
0
1
0
1
2
0
1
1
0
1
0
1
2
0
1
0
1
1
0
1
2
1
Off  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
kHz(***.* or ERR)  
Hz(***.* or ERR)  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
OK or ERR  
ERR  
Auto Power Off  
Auto Restart  
STANDBY Mode  
PRJ Mode  
On  
W
W
S
S
T
T
E
E
Off  
On  
Off  
Quick Start  
Eco  
Reverse  
On  
Off  
On  
Off  
I
I
I
Invert  
N
N
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
U
U
K
K
Q
Q
D
D
S
U
U
O
O
O
N
N
N
N
V
Language  
English  
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
S
S
A
A
T
Deutsch  
Español  
Nederlands  
Français  
Italiano  
Svenska  
Português  
1
1
1
1
1
1
1
1
polski  
Türkçe  
L
L
Magyar  
Tiếng Việt  
On  
L
1
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Setup Guide  
G
G
P
P
R
R
M
M
E
S
S
C
C
C
M
M
E
E
I
Off  
Internal Speaker  
RGB Frequency Check  
Fan Mode  
On  
Off  
Horizontal  
Vertical  
Normal  
High  
T
H
H
I
V
V
W
W
W
Q
Q
3
3
3
C
C
C
L
Input Search *2  
Video Setup  
Start  
0 IRE  
7.5 IRE  
Off  
Wall Color  
Blackboard  
Whiteboard  
On  
Quick Start Menu  
DLP® LinkTM  
Off  
Off  
On  
DLP® LinkTM Invert  
Closed Caption  
(For Americas only)  
Off  
C
C
C
R
A
A
A
E
CC1  
CC2  
L
L
Lamp Timer Reset *3  
P
0
0
0
OK or ERR  
*1 For setting the projector name, send the commands in the order of PJN1, PJN2 and PJN3.  
*2 When the next command is sent during input search, you may receive an “ERR” response code, and the input  
search is canceled.  
*3 The Lamp Timer Reset command is available only in standby mode.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compatibility Chart  
Computer  
•
Multiple signal support  
Horizontal Frequency: 15-110 kHz,  
Vertical Frequency: 45-85 Hz,  
Pixel Clock: 12-165 MHz  
Sync signal: Compatible with TTL level  
Compatible with sync on green signal  
•
Horizontal frequency  
[kHz]  
Analog  
Support  
Digital  
Support  
PC/MAC  
Mode  
Resolution  
Vertical frequency [Hz]  
Display  
31.5  
37.9  
37.5  
43.3  
35.2  
37.9  
48.1  
46.9  
53.7  
48.4  
56.5  
60.0  
68.7  
45.0  
47.8  
49.7  
62.8  
47.7  
47.8  
55.9  
55.0  
66.2  
67.5  
60.0  
75.0  
64.0  
80.0  
64.0  
65.3  
65.3  
75.0  
34.9  
49.7  
60.2  
60  
72  
75  
85  
56  
60  
72  
75  
85  
60  
70  
75  
85  
60  
60  
60  
75  
60  
60  
60  
60  
70  
75  
60  
75  
60  
75  
60  
60  
60  
60  
67  
75  
75  
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
VGA  
640 × 480  
✔
✔
✔
✔
SVGA  
XGA  
800 × 600  
1024 × 768  
Upscale  
✔
✔
✔
1280 × 720  
1280 × 768  
✔
✔
✔
TRUE  
PC  
WXGA  
1280 × 800  
1360 × 768  
1366 × 768  
1440 × 900  
✔
✔
WXGA+  
1152 × 864  
SXGA  
✔
Intelligent  
Compression  
1280 × 960  
1280 × 1024  
1400 × 1050  
✔
✔
✔
✔
SXGA+  
WSXGA+  
UXGA  
VGA  
SVGA  
XGA  
1680 × 1050  
1600 × 1200  
640 × 480  
832 × 624  
1024 × 768  
MAC 13”  
MAC 16”  
MAC 19”  
Upscale  
MAC 21”  
SXGA  
1152 × 870  
68.7  
75  
✔
Intelligent Compression  
Note  
• Optimum image quality will be achieved by matching your computer's output resolution to the  
resolution that corresponds to “TRUE” in the “Display” column shown above.  
• When “Screen resolution” of the computer is different from the resolution displayed on the projected  
image, follow the procedures shown below.  
– Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in  
“Screen resolution” of the computer.  
–
Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”  
adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is  
recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3D Supported Signals  
Analog  
Support  
Digital  
Support  
Signal  
Horizontal Frequency (kHz)  
Vertical Frequency (Hz)  
×
77.1  
98.6  
92.6  
101.6  
120  
120  
120  
✔
✔
✔
✔
✔
✔
✔
✔
SVGA  
XGA  
800 600  
×
1024 768  
×
1280 720  
WXGA  
1
×
120 *  
1280 800  
*1 Reduced Blanking  
Note  
•
Your computer graphics card must be able to display 3D stereoscopic signals.  
Please check with your computer/graphic card specifications or call your computer manufacturer to  
ensure this capability.  
DTV  
Horizontal  
Vertical  
Analog  
Support  
Digital  
Support  
Horizontal  
Vertical  
Analog  
Support  
Digital  
Support  
Signal  
Signal  
Frequency (kHz) Frequency (Hz)  
Frequency (kHz) Frequency (Hz)  
15.7  
31.5  
33.8  
15.6  
31.3  
37.5  
45.0  
33.8  
60  
60  
60  
50  
50  
50  
60  
60  
✔
✔
✔
✔
✔
✔
✔
✔
28.1  
33.8  
27.0  
28.1  
33.8  
56.3  
67.5  
50  
60  
24  
25  
30  
50  
60  
✔
✔
✔
✔
✔
✔
✔
✔
480I  
480P  
540P  
576I  
576P  
720P  
720P  
1035I  
1080I  
1080I  
1080P  
1080P  
1080P  
1080P  
1080P  
✔
✔
✔
✔
✔
✔
✔
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
Problem  
Check  
Page  
21  
• Projector power cord is not plugged into the wall outlet.  
• Power to the external connected devices is off.  
• The selected Input mode is wrong.  
–
27  
• The AV Mute function is working.  
27  
• Cables are incorrectly connected to the projector.  
• Remote control battery has run out.  
19–22  
13  
No picture and no sound  
or projector does not  
start.  
•
External output has not been set when connecting a notebook computer. 19  
• The lamp unit cover is not installed correctly.  
57, 58  
• Cables are incorrectly connected to the projector.  
• “Bright” is set to minimum position.  
19–22  
39  
• Depending on the computer you are using, an image may not be  
projected unless the signal output setting of the computer is switched  
to the external output. Refer to the computer's operation manual for  
how to switch its signal output settings.  
–
• Is “On” selected in “DLP® LinkTM”?  
52  
Sound is heard but no  
picture appears  
(or picture is dark).  
45  
39  
• Check that “Wall Color” is configured correctly.  
Dark or bluish image  
• Image adjustments are incorrectly set.  
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the  
“BrilliantColorTM” value.  
(Video Input only)  
• Video input system is incorrectly set.  
(COMPUTER/COMPONENT Input only)  
• Input signal type (RGB/Component) is incorrectly set.  
42  
41  
Color is faded or poor.  
• Adjust the focus.  
24  
17  
–
• The projection distance exceeds the focus range.  
•
There is fog on the lens. If the projector is carried from a cold room into a  
warm room, or if it is suddenly heated, condensation may form on the surface  
of the lens and the image will become blurred. Set up the projector at least  
one hour before it is to be used. If condensation should form, remove the  
power cord from the wall outlet and wait for it to clear.  
Picture is blurred;  
noise appears.  
(Computer Input only)  
• Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment)  
• Noise may appear depending on the computer.  
41  
–
• Cables are incorrectly connected to the projector.  
19–22  
27  
• Volume is set to minimum.  
• When the projector is connected to an external device and the volume  
is set to minimum, the sound is not output even if you turn up the  
volume of the external device.  
• “Speaker” is set to “Off”.  
• The Audio Mute function is working.  
46  
49  
Picture appears but no  
sound is heard.  
• Make the necessary adjustments of each item in the “SIG-ADJ” menu. 41  
Data image is not  
centered.  
• Depending on the computer you are using, the output resolution signal  
may be different from the one you have set. For details, refer to the  
operation manual of the computer.  
–
• If the picture is normal, the sound is due to cabinet shrinkage caused  
by room temperature changes. This will not affect operation or  
performance.  
–
An unusual sound is  
occasionally heard from  
the cabinet.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Check  
Page  
54  
• See “Maintenance Indicators”.  
Maintenance indicator on  
the projector illuminates  
or blinks in red.  
• Change the input signal type setting.  
41  
Picture is green on  
COMPUTER (YPbPr)/  
HDMI (YPbPr)  
Picture is pink  
(no green) on  
COMPUTER (RGB)/  
HDMI (RGB)  
• Image adjustments are incorrectly set.  
39  
Picture is too bright and  
whitish.  
• When temperature inside the projector increases, the cooling fan runs 8, 9  
The cooling fan becomes  
noisy.  
faster.  
53, 54, 55  
• The lamp indicator is illuminating in red.  
Replace the lamp.  
54, 57, 58  
The lamp does not light  
up even after the  
projector turns on.  
The lamp suddenly turns  
off during projection.  
• Cables are incorrectly connected to the projector or the connected  
equipment works improperly.  
19–22  
The image sometimes  
fl ic k e r s .  
• If this happens frequently, replace the lamp.  
57  
57  
• The lamp will eventually need to be changed.  
While the remaining lamp life draws to a close, replace the lamp.  
The lamp needs much  
time to turn on.  
Picture is dark.  
• Operate the remote control while pointing it at the projector's remote  
control sensor.  
• The remote control may be too far away from the projector.  
• If direct sunlight or a strong fluorescent lamp is shining on the  
projector's remote control sensor, place the projector where it will not  
be affected by strong light.  
13  
13  
The remote control  
cannot be used.  
• The batteries may be depleted or inserted incorrectly. Make sure the  
batteries are inserted correctly or insert new ones.  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting (Continued)  
Problem  
Check  
Page  
• Images may appear to flicker when fluorescent light or ambient light  
enters your vision.  
– Turn off the lights.  
–
–
–
3D images flicker when  
watching in a room.  
– Block any ambient light.  
• Check that you are using 3D LCD shutter glasses that support the  
Ghosting (a double image)  
occurs without the image  
appearing in 3D.  
DLP® Link™ system.  
– Be sure to use 3D LCD shutter glasses that support the DLP® Link™  
system.  
• Check that the shutters on the 3D LCD shutter glasses are working  
properly.  
– Turn the 3D LCD shutter glasses off and then on again.  
– Check the batteries of the 3D LCD shutter glasses.  
– Check that the 3D LCD shutter glasses are set to 3D viewing mode.  
Some 3D LCD shutter glasses are equipped with a special viewing  
mode (such as “dual view mode”) in addition to the normal 3D  
viewing mode. See the operation manual of your 3D LCD shutter  
glasses.  
• Check the settings of the projector.  
–
– Turn the DLP® Link™ function “On”.  
– Use “DLP® Link™ Invert” to change the setting.  
• Check whether a signal that is not supported is being input.  
– Configure your 3D application at the correct resolution and refresh  
rate.  
65  
Make sure you are running your 3D application in resolutions that  
support 3D. To support 3D, your 3D application must be configured  
to run at the correct settings for this projector.  
For details on the supported signals, see “3D Supported Signals” of  
the Compatibility Chart.  
• If the projector is connected to a computer for 3D image playback,  
check that a stereoscopically-enabled application is being used.  
– Use the applicable software.  
–
–
– Set the applicable software to the field sequential format.  
• Check that there are no obstructions between the screen and the 3D  
LCD shutter glasses.  
– Remove any obstructions.  
Any obstructions may cause the glasses not to function properly  
causing the lenses to flicker or turn off. Do not place your hand or  
other objects in front of the 3D control signal sensor on the glasses.  
• Check whether there is a source of high intensity lighting nearby.  
– Block the light or turn it off.  
–
–
High intensity lighting can interfere with communication between the  
3D LCD shutter glasses and the screen resulting in some flicker.  
• Check whether two or more projectors are projecting 3D images at the  
same time.  
– Use only one projector at a time.  
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect  
operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5  
minutes.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For SHARP Assistance  
If you encounter any problems during setup or operation of this projector, first  
refer to the “Troubleshooting” section on pages 66 to 68. If this operation  
manual does not answer your question, please contact the SHARP Service  
departments listed below.  
U.S.A.  
Sharp Electronics Corporation  
1-888-GO-SHARP (1-888-467-4277)  
[email protected]  
Denmark  
SHARP Electronics (Nordic) AB  
(0) 70 230 810  
[email protected]  
www.sharp.dk  
http://www.sharpusa.com  
Canada  
Mexico  
Sharp Electronics of Canada Ltd.  
(905) 568-7140  
Austria  
SHARP Electronics (Europe) GmbH  
0820 - 50 08 20  
EUR 0,145/min, Anrufe aus dem  
Mobilfunknetz können teurer sein  
www.sharp.at  
http://www.sharp.ca  
Sharp Electronics Corporation  
Mexico Branch  
(525) 716-9000  
Benelux  
SHARP Electronics Benelux BV  
0900-SHARPCE (0900-7427723)  
Nederland  
http://www.sharp.com.mx  
Latin America Sharp Electronics Corp. Latin  
American Group  
9900-0159 Belgium  
http://www.sharp.nl  
(305) 264-2277  
[email protected]  
http://www.siempresharp.com  
http://www.sharp.be  
http://www.sharp.lu  
Australia  
Sharp Corporation of Australia Pty.  
Ltd.  
1300-135-022  
http://www.sharp.net.au  
Germany  
Sharp Electronics (Europe) GmbH  
01805- 29 95 29  
0,14 €/Min. aus dem dt. Festnetz,  
Mobilfunkpreis max. 0,42 €/Min.  
http://www.sharp.de  
New Zealand Sharp Corporation of New Zealand  
Phone: (09) 573-0111  
U.K.  
Sharp Electronics (U.K.) Ltd.  
08705 274277  
http://www.sharp.co.uk/customersupport  
Fax: (09) 573-0112  
http://www.sharp.net.nz  
Singapore  
Hong Kong  
Taiwan  
Sharp-Roxy Sales (S) Pte. Ltd.  
65-226-6556  
[email protected]  
http://www.sharp.com.sg  
Italy  
Sharp Electronics (Italy) S.P.A.  
(39) 02-89595-1  
http://www.sharp.it  
France  
Spain  
SHARP ELECTRONICS FRANCE  
Tel: 0820 856 333  
http://www.sharp.fr  
Sharp-Roxy (HK) Ltd.  
(852) 2410-2623  
[email protected]  
http://www.sharp.com.hk  
SHARP ELECTRONICA ESPAÑA, S.A.  
902 10 13 88  
[email protected]  
http://www.sharp.es  
Sharp Corporation (Taiwan)  
0800-025111  
http://www.sharp-scot.com.tw  
Switzerland  
SHARP ELECTRONICS (SCHWEIZ)  
AG  
Malaysia  
U.A.E.  
Sharp-Roxy Sales & Service Co.  
(60) 3-5125678  
Sharp Infoline deutsch:  
0848 074 277 (Montag bis Freitag von  
09:00-18:00 Uhr)  
Sharp Middle East Fze  
971-4-81-5311  
[email protected]  
Sharp Infoline français:  
0848 274 277 (Lundi jusqu'à vendredi  
de 09:00-18:00 heures)  
http://www.sharp.ch  
Thailand  
Korea  
Sharp Thebnakorn Co. Ltd.  
02-236-0170  
[email protected]  
http://www.sharp-th.com  
Sweden  
Norway  
Finland  
SHARP Electronics (Nordic) AB  
0200 120 800  
[email protected]  
www.sharp.se  
Sharp Electronics Incorporated of  
Korea  
(82) 2-3660-2002  
SHARP Electronics (Nordic) AB  
22 07 42 82  
[email protected]  
www.sharp.no  
[email protected]  
http://www.sharpkorea.co.kr  
India  
Sharp Business Systems (India)  
Limited  
SHARP Electronics (Nordic) AB  
(09) 146 1500  
[email protected]  
www.sharp.fi  
(91) 11- 6431313  
[email protected]  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Model  
Display devices  
Resolution  
PG-LW2000  
0.65" DLP® Chip ×1  
WXGA (1280 × 800)  
F 2.5 – 2.7  
Manual, x 1.2  
Manual  
Lens  
F number  
Zoom  
Focus  
f = 21.8 – 25.6 mm  
×1  
×1  
Input terminals HDMI  
Computer/Component  
(mini D-sub 15 pin)  
Video (RCA)  
×1  
Audio (RCA)  
RS-232C (D-sub 9 pin)  
×1 (L/R)  
×1  
Control and  
communication  
terminals  
Speaker  
2 W (Mono)  
Projection lamp  
Rated voltage  
Rated frequency  
Input current  
210 W  
AC 100 – 240 V  
50/60 Hz  
2.7 A  
Power consumption  
Eco+Quiet  
Off  
AC 100 V  
AC 240 V  
267 W  
254 W  
Eco+Quiet AC 100 V  
On  
218 W  
207 W  
AC 240 V  
Power consumption  
(STANDBY Mode)  
Quick Start AC 100 V  
AC 240 V  
2.5 W  
2.9 W  
Eco  
AC 100 V  
AC 240 V  
0.5 W  
0.85 W  
Operation temperature  
Cabinet  
Dimensions (main body only) [W × H × D]  
41ºF to 95ºF (+5ºC to +35ºC)  
Plastic  
12 3/32" × 3 45/64" × 9 21/32"  
(307 × 94 × 245 mm)  
Weight (approx.)  
5.1 lbs. (2.3 kg)  
As a part of policy of continuous improvement, SHARP reserves the right to make design and  
specification changes for product improvement without prior notice. The performance specification  
figures indicated are nominal values of production units. There may be some deviations from these  
values in individual units.  
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,0240,000  
pixels (micromirrors). As with any high technology electronic equipment such as large screen  
TVs, video systems and video cameras, there are certain acceptable tolerances that the  
equipment must conform to.  
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots  
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions  
Units: inches (mm)  
12 3/32 (307)  
3 5/32 (80)  
13/64  
(5)  
1 23/32  
(43.5)  
1 1/4  
(31.5)  
M4 M4  
M4  
5 3/32 (129)  
4 31/32 (126)  
• Screw hole specs: 75 mm × 104 mm  
•
•
•
Depth of mounting holes: 8 mm  
Standard screw: M4 (pitch 0.7 mm)  
Quantity: 3  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
16:9·············································································28, 29  
3D MODE button······························································52  
MAGNIFY buttons ····························································31  
MENU button····································································35  
Accessories········································································3  
AC socket·········································································21  
Adjustment buttons····················································35, 36  
Adjustment foot································································25  
All Reset ···········································································49  
AREA ZOOM ····································································29  
Aspect ratio ······································································28  
Audio input ·······································································27  
AUDIO terminal·································································21  
Audio Mute·······································································49  
Auto Power Off·································································46  
Auto Restart ·····································································46  
Auto Sync (Auto Sync adjustment) ····························31, 46  
AUTO SYNC button··························································31  
AV MUTE button·······························································27  
NATIVE··············································································28  
NORMAL ····································································28, 29  
ON button·········································································23  
Optional accessories··························································3  
OSD Display ····································································44  
Overscan ··········································································44  
Phase················································································41  
Picture Adjustment ··························································38  
Picture Mode······························································31, 38  
PICTURE MODE button ···················································31  
POINTER button·······························································30  
Power cord·······································································21  
Power indicator ································································54  
PRJ-ADJ1/2······································································46  
PRJ Mode···································································18, 45  
Background······································································45  
Batteries ···········································································13  
Blue ··················································································39  
BORDER·····································································28, 29  
BREAK TIMER button ······················································30  
Bright················································································39  
BrilliantColorTM ·································································39  
Quick Start Menu ·····························································36  
Red···················································································39  
Remote control·································································12  
Remote control sensor·····················································13  
Replacing the lamp·····················································56, 57  
Resize·········································································28, 43  
RESIZE button··································································28  
Resolution·········································································41  
RETURN button································································35  
RGB cable ········································································19  
RS-232C terminal·····························································22  
Clock ················································································41  
Closed Caption·································································44  
CLR Temp (Color Temperature)········································39  
C.M.S. ··············································································39  
Color·················································································39  
Complete Menu································································36  
COMPUTER/COMPONENT input terminal ················19, 20  
Contrast············································································39  
DLP® LinkTM ······································································52  
DLP® LinkTM Invert ····························································52  
DNR··················································································40  
Dynamic Range································································41  
SCR-ADJ··········································································43  
Screen Size and Projection Distance ·······························17  
Security bar ······································································10  
Setup Guide ·······························································24, 45  
Sharp················································································39  
SIG-ADJ ···········································································41  
Signal Info·········································································42  
Signal Type·······································································41  
Speaker ············································································46  
SPOT button·····································································30  
STANDBY button······························································23  
STANDBY Mode·······························································49  
STANDBY/ON button ·······················································23  
Supplied accessories ·························································3  
System Lock·····································································47  
Eco+Quiet···································································30, 40  
ECO+QUIET button··························································30  
EFFECT button·································································30  
ENTER button···································································35  
Exhaust vent·······························································11, 53  
Fan Mode ·········································································46  
Film Mode·········································································40  
Focus ring·········································································24  
FREEZE button·································································31  
FULL·················································································28  
FUNCTION button····························································12  
FUNCTION Button setting················································49  
Temperature warning indicator·········································54  
Tint····················································································39  
Video Setup······································································42  
Video System ···································································42  
VIDEO terminal·································································20  
VOL (Volume) buttons·······················································27  
V-Pos················································································41  
V-STRETCH······································································29  
HDMI terminal····························································· 19-21  
HEIGHT ADJUST lever·····················································25  
H-Pos ···············································································41  
Image shift········································································43  
Information ·······································································36  
INPUT modes···································································27  
Input Search Start ····························································36  
Intake vent··································································10, 53  
Wall Color·········································································45  
Zoom ring·········································································25  
Kensington Security Standard connector ························11  
Keycode ··········································································47  
Keylock ············································································48  
KEYSTONE button ··························································26  
Keystone Correction···················································26, 43  
Lamp ················································································56  
Lamp indicator ·································································54  
Lamp Timer (Life)······························································49  
Lamp unit ·········································································57  
Language (on-screen display language) ··························45  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp Car Speaker GX BT7 User Manual
Shure Microphone w10bt User Manual
Sony Camcorder ca d50 User Manual
Sony Car Stereo System CDX M20 User Manual
Sony Cell Phone D5102 D5103 D5106 User Manual
Sony CRT Television KDL 60R510A User Manual
Sony Digital Camera CCD TR87 User Manual
Sony Radio SRF M97 User Manual
Sony Stereo Receiver Model STR DK5 User Manual
Tanita Computer Monitor BC 532 User Manual