LC-52SB55U
LIQUID CRYSTAL
TELEVISION
OPERATION MANUAL
ENGLISH
IMPORTANT : Please read this operation manual
before starting operating the equipment.
Supplied Accessories
Make sure the following accessories are provided with the product.
Remote control unit ( 1)
“AA” size battery ( 2)
AC cord ( 1)
Page 8
Cable clamp ( 1)
Stand unit ( 1)
g
g
g
g
g
Page 8
Page 9
Cable tie ( 1)
Page 7
g
Page 8
■ Operation manual (g3 languages)
• Always use the AC cord supplied with the TV.
• AC cord enclosed in this product is for 110-125V. In using it on the 125-240V AC, please consult the following.
SHARP ELECTRONICS CORPORATION, LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved
cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-52SB55U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
TEL: 1-800-BE-SHARP
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the
National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical."
This product utilizes tin-lead solder, and fluorescent lamp
containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local
Sharp at 1-800-BE-SHARP
(For U.S.A. only)
Trademarks
• Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of
Dolby Laboratories.
• "HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC."
• Products that have earned the ENERGY STAR are designed to protect the environment through superior
energy efficiency.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts—When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
• Outdoor Antenna Grounding — If an outside antenna is
connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against
voltage surges and built-up static charges.
ANTENNA
LEAD IN WIRE
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC — NATIONAL ELECTRICAL CODE
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may
scratch the panel surface.
• Use a soft damp cloth to gently wipe the panel when it is really dirty.
(It may scratch the panel surface when wiped strongly.)
• If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to clean it, such materials may damage
the panel surface.
• To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base
can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper
ventilation is provided or the manufacturer's instructions are followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.
• Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 2,073,600 pixels, giving you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that
this does not affect the performance of your product.
• Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to
the equipment due to lightning and power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may
result in fire or electric shock. Exercise special caution when using the product around children.
Precautions when transporting the TV
• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always
carry the TV by two people holding it with two hands — one hand on each side of the TV.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat Panel Display
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:
THE ISSUE
•
The home theater entertainment experience is a growing trend and larger flat panel
displays are popular purchases. However, flat panel displays are not always supported
on the proper stands or installed according to the manufacturer’s recommendations.
Flat panel displays that are inappropriately situated on dressers, bookcases, shelves,
desks, speakers, chests or carts may fall over and cause injury.
•
THIS MANUFACTURER CARES!
•
The consumer electronics industry is committed to making home entertainment enjoyable
and safe.
TUNE INTO SAFETY
•
One size does NOT fit all. Follow the manufacturer’s recommendations for the safe
installation and use of your flat panel display.
•
•
•
Carefully read and understand all enclosed instructions for proper use of this product.
Don’t allow children to climb on or play with furniture and television sets.
Don’t place flat panel displays on furniture that can easily be used as steps, such as
a chest of drawers.
•
Remember that children can become excited while watching a program, especially
on a “larger than life” flat panel display. Care should be taken to place or install the
display where it cannot be pushed, pulled over, or knocked down.
Care should be taken to route all cords and cables connected to the flat panel
display so that they cannot be pulled or grabbed by curious children.
•
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT
PANEL DISPLAY, ALWAYS:
•
Use a mount that has been recommended by the display manufacturer and/or listed
by an independent laboratory (such as UL, CSA, ETL).
•
•
Follow all instructions supplied by the display and wall mount manufacturers.
If you have any doubts about your ability to safely install your flat panel display,
contact your retailer about professional installation.
•
Make sure that the wall where you are mounting the display is appropriate. Some
wall mounts are not designed to be mounted to walls with steel studs or old cinder
block construction. If you are unsure, contact a professional installer.
A minimum of two people are required for installation. Flat panel displays can be
heavy.
•
Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S.
consumer electronics industry. More than 2,200 companies enjoy the benefits of CEA
membership, including legislative advocacy, market research, technical training and education,
industry promotion and the fostering of business and strategic relationships.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK REFERENCE
Attaching/Detaching the Stand
Setting the TV on the Wall
•
•
Before attaching (or detaching) the stand, unplug the AC
cord from the AC INPUT terminal.
Before performing work spread cushioning over the base
area to lay the TV on. This will prevent it from being
damaged.
CAUTION
• This TV should be mounted on the wall only with the
AN-52AG4 (SHARP) wall mount bracket. The use of
other wall mount brackets may result in an unstable
installation and may cause serious injuries.
• Installing the TV requires special skill that should
only be performed by qualified service personnel.
Customers should not attempt to do the work
themselves. SHARP bears no responsibility for
improper mounting or mounting that results in
accident or injury.
CAUTION
• Attach the stand in the correct direction.
• Do not remove the stand from the TV unless using an
optional wall mount bracket to mount it.
• Be sure to follow the instructions. Incorrect installation
of the stand may result in the TV falling over.
Using an optional bracket to mount the TV
1 Confirm that there are 12 screws (all the same size)
and a hex key supplied with the stand unit.
•
You can ask a qualified service professional about
using an optional AN-52AG4 bracket to mount the TV
to the wall.
• Carefully read the instructions that come with the
bracket before beginning work.
2
1 Set the post for the stand unit onto the box.
2 Attach the base to the post.
3 Insert and tighten the 8 screws into the 8 holes
on the bottom of the base.
Hanging on the wall
AN-52AG4 wall mount bracket.
(See the bracket instructions for details.)
Hex key
3
Screws
Vertical mounting
Angular mounting
2
About setting the TV angle
•
•
The center of the display:
1
19
/
64 inch (7.3 mm) under
the “ f ” position.
1
Refer to the operation
manual of AN-52AG4 for
details.
3
1 Insert the stand into the openings on the bottom
of the TV.
2 Insert and tighten the 4 screws into the 4 holes
on the rear of the TV.
Hex key
Screws
Soft cushion
2
2
• Detach the cable clamp on the rear of the TV when using
the optional mount bracket.
• To use this TV mounted on a wall, remove the covers at
the 4 locations on the rear of the TV, and then use the
screws supplied with the wall mount bracket to secure the
bracket to the rear of the TV.
1
1
• To detach the stand, perform the steps in reverse order.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
QUICK REFERENCE
QUICK INSTALLATION TIPS
Using the Remote Control Unit
Use the remote control unit by pointing it towards the
remote control sensor on the TV. Objects between the
remote control unit and the remote control sensor may
prevent proper operation.
Attach your antenna to the back of the television.
1
(See page 9.)
Connect the AC plug for the television into the AC
outlet.
2
Remote Control sensor
30º
17´ (5 m)
30º
30º
30º
AC outlet
• Place the TV close to the AC outlet, and keep the power
plug within reach.
■ Cautions regarding the remote control unit
• Do not expose the remote control unit to shock. In addition,
do not expose the remote control unit to liquids, and do not
place in an area with high humidity.
• Do not install or place the remote control unit under direct
sunlight. The heat may cause deformation of the remote
control unit.
• The remote control unit may not work properly if the remote
control sensor on the TV is under direct sunlight or strong
lighting. In such cases, change the angle of the lighting
or the TV, or operate the remote control unit closer to the
remote control sensor.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
Place the Ferrite core in the space indicated in the
3
below figure and bundle the cords properly with
the cable clamp and the cable tie.
Ferrite core
IMPORTANT:
How to turn on the television for the first time.
A) Press POWER on the television.
The POWER indicator on the television should light GREEN
indicating you have power to the television.
4
If the POWER indicator on the television still does not light up,
press POWER on the remote control to turn the power on.
POWER
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE
TELEVISION FROM THE OUTLET AND REPEAT THE
INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT
US AT 1-800-BE-SHARP.
B) The POWER indicator on the front of the
television lights GREEN.
POWER
indicator
• Speakers cannot be detached from the TV.
• TV angle cannot be adjusted.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set.
F-type connector
1.A 75-ohm system is generally a round cable with F-type connector
that can easily be attached to a terminal without tools (Commercially
available).
75-ohm coaxial cable (round)
2.A 300-ohm system is a flat “twin-lead” cable that can be attached
to a 75-ohm terminal through a 300/75-ohm adapter (Commercially
available).
300-ohm twin-lead cable (flat)
NOTICE
F-type connector should be finger-tightened only.
F-type connector
When connecting the RF cable to the TV set, do not tighten F-type
connector with tools.
If tools are used, it may cause damage to your TV set. (The breaking
of internal circuit, etc.)
75-ohm coaxial cable
Connecting Antenna
Cable
• Connect the antenna cable to the TV using one of the methods in the illustration as shown (
,
,
or
).
4
1
2
3
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Cable without a CATV
converter
1
2
Coaxial cable
(commercially available)
VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
Coaxial cable
(commercially available)
Combination VHF/
UHF antenna
3
4
75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
or
300/75-ohm adapter
(commercially available)
UHF
Separate VHF/UHF
antenna
300-ohm
ANTENNA
twin-lead cable
VHF
ANTENNA
IN
OUT
Combiner
(commercially available)
300-ohm twin-lead cable
75-ohm coaxial cable
To TV antenna
terminal
or
Installing Batteries in the Remote Control Unit
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.
1 Open the battery cover.
2 Insert two “AA” size batteries
(supplied with the product).
3 Close the battery cover.
• Place the batteries with their terminals
corresponding to the ( ) and (
)
f
e
indications in the battery compartment.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage
in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a
rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names
TV (Front)
Remote control sensor
OPC sensor* (See page 18.)
OPC indicator (See page 18.)
SLEEP indicator (See page 13.)
POWER indicator (See page 12.)
* OPC: Optical Picture Control
TV (Rear/Side)
*2
POWER
button
*3
MENU
button
AC INPUT
terminal
INPUT
button
*1
INPUT 7 terminal
(HDMI)
Channel
buttons
(CHU/V)
DIGITAL AUDIO
OUTPUT terminal
INPUT 8 terminal
(HDMI)
Volume
buttons
(VOL
/
)
k l
AUDIO OUTPUT
terminals
*1
INPUT 5
terminal
(HDMI)
Antenna/Cable in
INPUT 1 terminals
INPUT 2 terminals
RS-232C terminal
INPUT 3
terminals
INPUT 4 terminal (PC-IN)
AUDIO terminal (shared for INPUT 4 and INPUT 6) *4
SERVICE
terminal
INPUT 6 terminal (HDMI)
*1 See page 11 for external equipment connection.
*2 See page 17 for button operations.
*3 See page 8 for connecting the AC cord.
*4 See page 24 for details on the PC Audio Select function.
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to External Equipment
You can connect many types of external equipment to your TV like a Blu-ray disc player, DVD player, VCR, Digital
TV tuner, HDMI equipment, game console or camcorder. To view external source images, select the input source
from INPUT on the remote control unit or on the TV. (See page 15.)
CAUTION
• To protect equipment, always turn off the TV before connecting any external equipment.
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.
Connecting a Blu-ray disc player, DVD player, Digital TV STB (Air or Cable), VCR,
game console or camcorder
Terminal on external
Terminal on the TV
INPUT 1 or 3
Cable
equipment
*1
AV cable (commercially available)
*1
*2
INPUT 1 or 2
Component video cable (commercially available)
Audio cable (commercially available)
*1
INPUT 2
S-VIDEO cable (commercially available)
Audio cable (commercially available)
*3
*4
INPUT 5, 6, 7 or 8
HDMI-certified cable (commercially available)
Optical fiber cable (commercially available)
DIGITAL AUDIO
OUTPUT
*1 • The COMPONENT terminals take priority over the VIDEO (INPUT 1) and S-VIDEO (INPUT 2) terminals.
*2 • To enjoy 1080p display capability, connect your external equipment using a component cable and set the
equipment to 1080p output.
*3 • When using an HDMI-DVI conversion cable, input the audio signal to AUDIO terminal of INPUT 6. When you input the
audio signal via the AUDIO terminal with INPUT 6, set "PC Audio Select" to "Input 6 (HDMI)". (See page 24.)
• To enjoy 1080p display capability, connect your Blu-ray disc player or other external equipment using an HDMI-certified
cable and set the equipment to 1080p output.
*4 • Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI
connection. In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.
Connecting a PC
Terminal on the TV
INPUT 4
Terminal on PC
Cable
RGB cable (commercially available)
Ø 3.5 mm stereo minijack cable (commercially available)
INPUT 5, 6, 7 or 8
HDMI-certified cable (commercially available)
• When connecting a PC to the INPUT 4, set "PC Audio Select" to "Input 4 (PC)". (See page 24.)
• The HDMI terminals only support digital signal.
• Refer to page 30 for a list of PC signals compatible with the TV.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Watching TV
Turning On/Off the Power
Press POWER on the TV or on the remote control unit to turn the
power on.
•
POWER indicator (Green): The TV is on. (After a few seconds, a window
appears with sound.)
POWER
•
The initial setup starts when the TV powers on for the first time. If the TV has
been turned on before, the initial setup will not be invoked. For changing the
settings of the initial setup, perform EZ setup on the Setup menu on page 20.
Press POWER on the TV or on the remote control unit again to turn the
power off.
•
•
The TV enters standby and the image on the screen disappears.
The POWER indicator on the TV turns off.
POWER
(On/Standby)
•
•
If you are not going to use this TV for a long period of time, be sure to remove
the AC cord from the AC outlet.
Weak electric power is still consumed even when the TV is turned off.
Initial Setup
Air/Cable (Antenna setting)
Make sure what kind of connection is made with your TV
when selecting "Air" or "Cable".
When you turn on the TV for the first time, it will
automatically memorize the broadcasting channels
available in the region where you live. Perform the
following steps before you press POWER on the
remote control unit.
1. Insert the batteries into the remote control unit. (See page 9.)
2. Connect the antenna cable to the TV. (See page 9.)
3. Plug in the AC cord to the AC outlet. (See page 8.)
Press
/
to select "Air" or "Cable".
c d
3
Press ENTER to enter the setting.
Example
Language
TV Location
Air/Cable
CH Search
Air
Cable
CH Search (Channel search)
Channel auto search makes the TV look for all channels
Language (Language setting)
Select from among 3 languages: English, French and Spanish.
viewable in the set area.
When "Air" is selected in Antenna setting:
4
Press
/
to select the desired language listed on the
a b
1
Press
/
to select "Start", and then press ENTER.
c d
screen, and then press ENTER.
Language
TV Location
Air/Cable
Language
TV Location
Air/Cable
English
Français
Español
CH Search
CH Search
Start
Cancel
When "Cable" is selected in Antenna setting:
Press
TV Location
/
to select "Analog & Digital Search Start" to
a b
Select "Home" or "Store" for the location where you plan to
install the TV.
search both analog and digital broadcasts, or to select
“Analog Search Start” to search only analog broadcasts,
and then press ENTER.
Press
/
to select "Home" or "Store".
c d
2
Press ENTER to enter the setting.
Language
Example
TV Location
Language
TV Location
Air/Cable
CH Search
Home
Air/Cable
Analog & Digital Search Start
Analog Search Start
Cancel
CH Search
Store
• The Channel search will start automatically.
• To exit the Channel search screen, select "Cancel", and
then press ENTER.
•
•
If you select "Home", AV MODE is set to "STANDARD".
If you select "Store", AV MODE is set to "DYNAMIC (Fixed)".
If there is no operation for 30 minutes, AV MODE will return
to "DYNAMIC (Fixed)" automatically, regardless of previous
changes to the AV MODE settings.
For changing the TV Location after the setting, see "EZ
Setup" on page 20.
•
If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
(See page 20.)
•
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Button Operation
Changing Volume
You can change the volume by pressing VOL
the TV or on the remote control unit.
/
on
k l
ԥ
ԝ
ԟ
Ԝ
Ԡ
ԛ
• To increase the volume, press VOL
• To decrease the volume, press VOL
.
k
.
l
Ԙ
Ԧ
20
Audio status
Output Select
Output device
Speaker
Fixed
Variable
ԙ
Variable sound
Mute
• When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
Ԟ
ԧ
Ԣ
ԣ
60
• See page 24 for details on the Output Select function.
ԡ
MUTE
Ԥ
Ԛ
Mutes the current sound output.
Press MUTE.
• "
" will be displayed on the screen for 30 minutes, and
the sound is silenced.
• Within 30 minutes of pressing MUTE, mute can be
canceled by using one of the methods below.
POWER
- Mute will be canceled if you press VOL
or MUTE.
/
k l
You can turn on the TV or put it on standby by
pressing POWER on the TV or on the remote control
unit. (See page 12.)
• Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
Changing Channels
Sleep Timer
U/V
You can change channels by pressing CH
or 0–9,
Allows you to set a time when the TV automatically
• (DOT).
switches to standby.
Examples:
Press SLEEP.
To select a 1 or 2-digit channel number (e. g., Channel 5):
•
The remaining time displays when the sleep timer has been set.
Press 5
To select a 3-digit channel number (e. g., Channel 115):
Press 1 ENT.
To select a 4-digit channel number (e. g., Channel 22.1):
Press 2 • (DOT) ENT.
ENT.
• Each time you press SLEEP, the remaining time switches
as shown below.
1
5
Off
30
60
90
120
2
1
• When set, the time automatically starts counting down.
• If you want to adjust the sleep timer, you can press SLEEP
twice then change the time setting.
• Five minutes before the time expires, the remaining time
displays every minute.
• When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
• When you enter 0–9 only, channel selection will be made if
there is no operation within a few seconds.
• Select "Off" by pressing SLEEP to cancel the sleep timer.
The TV will enter standby when the remaining time reaches zero.
When the sleep timer is set, its indicator on the TV lights red.
•
If you push "0" by itself, nothing will happen.
•
•
• Complete the above steps within a few seconds.
• When you enter 0–9 and • (DOT), channel selection will be
made if there is no operation within a few seconds.
FLASHBACK
Press FLASHBACK to switch to the previously tuned
FAVORITE CH
You can select 4 preset favorite channels in 4 different
categories.
Press A, B, C or D.
• While watching the TV, you can toggle the selected
channels by pressing A, B, C and D.
channel.
• Press FLASHBACK again to switch back to the currently
tuned channel.
• FLASHBACK will not work if no channel has been changed
after the TV is turned on.
• See page 25 for details of favorite channel settings.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Button Operation
AV MODE
AUDIO
AV MODE gives you several viewing options to choose
from to best match the surrounding environment of the
TV, which can vary due to factors like room brightness,
type of program watched or the type of image input
from external equipment.
■ MTS/SAP stereo mode
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The TV
with MTS can receive mono sound, stereo sound
and Secondary Audio Programs (SAP). The SAP
feature allows a TV station to broadcast other
information, which could be audio in another language
or something completely different like weather
information.
Press AV MODE. Current AV MODE displays.
• Press AV MODE again before the mode displayed on the
screen disappears. The mode changes as shown below:
Example:
When the input source is TV, INPUT 1, 2 or 3 terminals
You can enjoy Hi-Fi stereo sound or SAP broadcasts
where available.
STANDARD
DYNAMIC
Example:
MOVIE
GAME
USER [TV]
• Stereo broadcasts: View programs like live sporting
events, shows and concerts in dynamic stereo sound.
• SAP broadcasts: Receive TV broadcasts in either MAIN or
SAP sound. MAIN sound: The normal program soundtrack
(either in mono or stereo). SAP sound: Listen to a second
language, supplementary commentary or other information.
(SAP is mono sound.)
DYNAMIC (Fixed)
When the input source is INPUT 4, 5, 6, 7 or 8
terminals
STANDARD
DYNAMIC
MOVIE
GAME
PC
USER[
DYNAMIC (Fixed)
]
If stereo sound is difficult to hear.
• Obtain a clearer sound by manually switching to fixed
mono-sound mode.
STANDARD: For a highly defined image in a normal
lighting.
[Enhanced Picture Contrast: on]
MOVIE: For a movie.
You can change MTS as shown below to match the television
broadcast signal.
[Enhanced Picture Contrast: off]
GAME: Lowers image brightness for easier viewing.
[Enhanced Picture Contrast: off]
PC: For PC.
[Enhanced Picture Contrast: off]
USER: Allows the user to customize settings as desired.
You can set the mode for each input source.
[Enhanced Picture Contrast: off]
Press AUDIO to toggle between audio modes.
Examples: when receiving MTS and SAP
STEREO
MONO
STEREO mode:
STEREO + SAP mode:
ST(SAP) SAP(ST)
MONO
MAIN
SAP
MAIN + SAP mode:
MONO mode: MONO
DYNAMIC (Fixed): Changes the image and sound
settings to the factory preset values. No adjustments
are allowed.
■ Digital broadcasting audio mode
The types of audio transmitted in a digital broadcast include
SURROUND as well as MONO and STEREO. In addition, it
is possible for multiple audio tracks to accompany a single
video track.
[Enhanced Picture Contrast: on]
DYNAMIC: For a clear-cut image emphasizing high
contrast, useful for sports viewing.
[Enhanced Picture Contrast: on]
Press AUDIO to toggle between audio modes.
Example: when receiving Digital broadcasting
STEREO (Audio1)
STEREO (Audio2)
• You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for INPUT 1.)
SURROUND (Audio3)
• When you play games, "GAME" is recommended for AV
MODE.
• MTS only operates while in TV mode.
• "Enhanced Picture Contrast" technology detects the source
video characteristics and smoothly adjusts the screen
brightness accordingly to realize deeper black levels.
FREEZE
Allows you to capture and freeze a moving image that
you are watching.
Press FREEZE.
• A moving image is captured.
• Press FREEZE again to cancel the function.
• When this function is not available, "No displaying still
image available." will display.
• The still image automatically goes out after 30 minutes.
• If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
canceled and a V-CHIP BLOCK message will appear.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Button Operation
INPUT
To view external source images, select the input source
using INPUT on the remote control unit or on the TV.
In the Closed Caption system, there can be more than
one caption service provided. Each is identified by its
own number. The “CC1” and “CC2” services display
subtitles of TV programs superimposed over the
program's picture.
Press INPUT.
• A list of selectable sources appears.
1
Press INPUT again or press
/
to select the
a b
2
In the Closed Caption system, the “Text1” or “Text2”
services display text that is unrelated to the program
being viewed (e.g., weather or news). These services
are also superimposed over the program currently
being viewed.
input source.
•
An image from the selected source automatically displays.
• Each time INPUT is pressed, the input source toggles.
•
If the corresponding input is not plugged in, you cannot change
the input. Be sure to connect the equipment beforehand.
Press CC.
1
2
• See page 11 for external equipment connection.
• Press PC to switch to an image from the PC.
• This will present the Closed Caption information display.
Press CC while the Closed Caption information is
still on the screen.
• Press repeatedly until you select the desired closed
caption service.
PC
Allows you to gain quick access to PC mode.
Press PC.
Air
DIGITAL
Operating On-Screen Display Menu
You can operate the on-screen display menu by using
the following buttons.
22.1
Audio
Video
CC
:
:
:
:
MONO
MENU: Displays the menu screen.
1080i (16:9)
1/2 CC1
NONE
/
/
/
, ENTER: Select a desired item on the
a b c d
Closed Caption
information
Ratings
screen.
RETURN: Returns to the previous menu screen.
Example:
EXIT: Turns off the menu screen.
If a program has three services (Digital CC(ENG), CC1
and Text1), the closed caption display will toggle in this
sequence:
• For operating the on-screen display menu, see “Menu
Operation Buttons” on page 17.
1/3 ENG
2/3 CC1 3/3 Text1 Off
DISPLAY
Displays channel information being viewed.
Press DISPLAY.
• The CC button keeps a record of the last service
selected in its memory.
If the last closed caption mode (e.g. 1/3ENG) you
selected is not available for the next program, or on
another channel, the closed caption service that is
available is automatically selected, and this service
appears in parentheses, e.g. “1/3(CC1)”.
Closed Caption services that appear in parentheses will
not be stored in the CC button's memory as your last
selected service. Only services that you have selected
with the CC button are stored.
Closed Captions and Digital Closed Captions
Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations, narration
and sound effects as subtitles on your TV. Closed
Captions are available on some TV programs and on
some VHS home video tapes at the discretion of the
program provider.
It is a more flexible system than the original Closed
Caption system, because it allows for a variety
of caption sizes and font styles. When the Digital
Closed Caption service is in use, it will be indicated
by the appearance of a 3-letter abbreviation that also
indicates the language of the Digital Closed Captions:
ENG (English), SPA (Spanish), FRA (French) or other
language codes.
• When “Power Saving” is set to “Standard” or “Advanced”,
the Power Saving leaf icon appears on the channel
information window. See page 19 for details of Power
Saving settings.
• See page 25 for detailed closed caption settings.
• When the program contains no closed caption, “--” displays
in the closed caption information.
• If the language code, e.g. “ENG”, is not found on Digital TV
programs, “--” will be shown.
Not all programs and VHS videotapes offer closed
captions. Please look for the “1” symbol to ensure
that captions will be shown.
• Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may contain
none or only some of these services at the discretion of the
program provider.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Button Operation
VIEW MODE
You can select the screen size.
Press VIEW MODE.
• The View Mode menu displays.
1
• The menu lists the View Mode options selectable for the type of video signal currently being received.
Press VIEW MODE or
/
while the View Mode menu is displayed to select a desired item on the menu.
a b
2
• You can sequentially select a View Mode that has its own aspect ratio.
■ For 4:3 programs
Example: Screen size images
Side Bar
S.Stretch (Smart stretch)
Zoom
Stretch
Suitable for viewing
conventional 4:3 programs in programs to fill the screen.
their normal format.
Suitable for stretching 4:3
Suitable for viewing wide-
screen 2.35:1 anamorphic
DVDs in full screen.
This mode is useful for 1.78:1
DVDs. When viewing 1.85:1
DVDs, stretch mode will still show
very thin black bands at the top
and bottom of the screen.
■ For HD programs
Stretch: Suitable for viewing wide-screen 1.78:1 aspect ratio program, stretch mode will still show very thin black bands at
the top and bottom of the screen.
Dot by Dot (1080i/p only): Detects the resolution of the signal and displays an image with the same number of pixels on
the screen.
Full Screen (720p only): You can select "Full Screen" only when receiving a 720p signal.
S.Stretch (Smart stretch): Suitable for stretching 4:3 programs to fill the screen.
Zoom: Suitable for viewing wide-screen 2.35:1 aspect-ratio programs in full screen.
•
When using Dot by Dot, it is possible to see noise or bars around different outer portions of the screen. Please change view
mode to correct this.
■ For PC input mode
• Connect the PC before making adjustments. (See page 11.)
• Selectable screen size may vary with input signal type.
Example: Screen size images
Input signal
Normal
Zoom
Stretch
Dot by Dot
4:3
Keeps the original
aspect ratio in a full
screen display.
For viewing
widescreen
programs. The top
and bottom of the
image is cropped.
An image fully fills the Detects the resolution
screen.
of the signal and
displays an image with
the same number of
pixels on the screen.
Input signal
Stretch
Dot by Dot
16:9
An image fully fills the Detects the resolution
screen.
of the signal and
displays an image with
the same number of
pixels on the screen.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
On-Screen Display Menu Operation
Example
Example
Option
Picture
Audio Only
PC Audio Select [Input4(PC)]
OPC
Off
On
On : Display
b16
Output select
[Fixed]
Backlight
Contrast
Brightness
Color
[b12] a16
Caption Setup
[b30]
0
b40
b30
b30
b30
b10
Digital Caption Info.
Program Title Display
Favorite CH
[
[
[
[
0] a30
0] a30
0] a30
b2] a10
[No]
[Off]
Tint
Operation Lock Out
Sharpness
Advanced
Reset
Item displayed in yellow
1
•
•
This indicates the item currently selected.
Press ENTER to go to the adjustment screen for this
item.
Item in brackets
2
3
4
ENTER
RETURN
MENU
: Exit
: Select
: Enter
: Back
•
This indicates the current setting for the item.
Item displayed in white
This indicates that the item can be selected.
•
The bar above is an operational guide for
the remote control. The bar will change in
accordance with each menu setting screen.
Item displayed in gray
•
This indicates that the item cannot be selected.
There are various reasons why the items cannot be
selected, but the main reasons are as follows:
—Nothing is connected to the selected input terminal.
—The function is not compatible with the current input
signal.
Press MENU to display the MENU screen.
Press c/d to select the desired menu.
Press a/b to select a specific adjustment item,
and then press ENTER.
1
2
1
2
• Menu options differ in the selected input modes, but the
operating procedures are the same.
• The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
Press a/b (or c/d) to select or adjust the
3
desired setting, and then press ENTER.
Press MENU to exit.
3
Menu Operation Buttons
Using the remote control
Use the following buttons on the remote control to
operate the menu.
Using the control panel of the main unit
You can also operate the menu with the control panel
of the main unit.
Button operations on the control panel correspond to
the ones on the remote control as shown below.
MENU: MENU on the
remote control.
INPUT: ENTER on the
remote control.
MENU:
Press to open or close the menu screen.
a
CHU/V: Cursor
/
b
/
/
/
:
Press to select a desired item on the screen or
adjust a selected item.
a b c d
on the remote
control.
ENTER:
Press to go to the next step or complete the
setting.
VOL
: Cursor
/
/
c d
on the remote
control.
k l
RETURN:
Press to return to the previous step.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Picture Menu
Adjusts the picture to your preference with the
following picture settings.
Color Temp.
(Color Temperature)
For a better white balance, use color temperature
correction.
Selected item
Backlight
button
The screen dims
button
d
The screen
brightens
For more contrast
For more
brightness
For more color
intensity
Skin tones
become greenish
For more
c
High:
White with bluish tone
Mid-High:
Middle:
Mid-Low:
Low:
Contrast
Brightness
For less contrast
For less
White with reddish tone
brightness
For less color
intensity
Color
White balance can be adjusted between a maximum of
+30 and a minimum of –30 for each color temperature.
R Gain: –30 through +30
Tint
Skin tones
become reddish
For less
G Gain: –30 through +30
B Gain: –30 through +30
Sharpness
sharpness
sharpness
• For resetting all Picture adjustment items to the factory
preset values, press to select "Reset", press ENTER,
/
a b
• For resetting all adjustment items to the factory preset
press
/
to select "Yes", and then press ENTER.
c d
values, press
ENTER.
/
to select "Reset", and then press
a b
OPC Setting
Automatically adjusts the brightness of the screen.
Off: The brightness is fixed at the value set in "Backlight".
On: Automatically adjusts.
Active Contrast
Automatically adjusts the image contrast according to
the scene.
On: Display: Displays the OPC effect on the screen while
adjusting the brightness of the screen.
On: Automatically adjusts the image contrast.
Off: No adjustment.
I/P Setting
• When set to "On", the Optical Picture Control (OPC) senses
the surrounding light and automatically adjusts the backlight
brightness. Make sure nothing obstructs the OPC sensor,
which could affect its ability to sense surrounding light.
• When set to "On: Display", OPC effect displays on the
screen while the OPC adjusts the screen brightness.
• When set to "On" or "On: Display", the OPC indicator on
the TV lights green.
Converts input signals depending on the type of
images.
Fast: Suitable for fast-moving images
Slow: Suitable for smooth images with low amounts of
flickers
• "I/P Setting" is not selectable when channel display shows
an input resolution of 480P, 720P or 1080P.
Advanced Picture Setting
This TV provides various advanced functions for
optimizing the picture quality.
Film Mode (3:2 pull-down)
Automatically detects a film-based source (originally
encoded at 24 frames/second), analyzes it then
recreates each still film frame for high-definition picture
quality.
C.M.S.
(Color Management System)
Color tone is managed using the six-color adjustment
setting.
On: Detects, analyzes, converts film source.
Off: Normal viewing mode.
C.M.S.-Hue: This is a standard to adjust the color either
more reddish or more bluish in tone.
• "Film Mode" does not function when you set the "AV Mode"
to "Game".
• "Film Mode" is not selectable when channel display shows
an input resolution of 480P, 720P or 1080P.
C.M.S.-Saturation: Increases or decreases the
saturation of a selected color.
• For resetting all adjustment items to the factory preset
values, press
ENTER.
/
to select "Reset", and then press
a b
18
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Digital Noise Reduction
Surround
Produces a clearer video image.
Off: No adjustment
Surround function allows you to enjoy realistic "live" sound.
On: Surround function is on.
High/Middle/Low: Select a desired level for viewing a
clearer video image.
Off: Normal sound.
• Audio menu is grayed out when Output Select is set to
"Variable".
• For some discs, setup may be required on your DVD player.
In this case, please refer to the operation manual of your
DVD player.
• "Digital Noise Reduction" is not selectable when channel
display shows an input resolution of 1080P.
3D-Y/C
Provides high quality images with minimal dot crawl
and cross color noise.
Bass Enhancer
This function allows you to enjoy bass-enhanced sound.
Slow: For still images.
On: Bass Enhancer function is on.
Standard: Normal adjustment.
Fast: For moving images.
Off: Normal sound.
Off (2D): For Game Mode.
• Audio menu is grayed out when Output Select is set to
"Variable".
• 3D-Y/C is available for input signal from Composite Video
and analog broadcasts (air and cable).
Power Control Menu
Power control setting allows you to save energy.
Monochrome
For viewing a video in monochrome.
On: For viewing in monochrome.
Power Saving
Off: Normal color.
This function allows you to automatically reduce the
backlight brightness in order to decrease the power
consumption and increase the backlight lifespan.
Standard: Reduces the backlight brightness to 80%.
Range of OPC
The brightness level range of the OPC sensor's
automatic adjustments can be set according to your
preferences.
The adjustment range of the OPC sensor can be set to
a maximum of +16 and a minimum of –16.
Max.: –15 through +16
When set to “Standard”, “ ” appears on the screen.
Advanced: Reduces the backlight brightness to 70%.
When set to “Advanced”, “
screen.
” appears on the
Off: The backlight brightness is the same value of your
settings in the selected AV MODE.
Min.: –16 through +15
• The range of OPC settings are active only when the OPC is
set to "On".
• The maximum setting cannot be set to a smaller number
than the minimum setting.
• The minimum setting cannot be set to a bigger number
than the maximum setting.
• Depending on the brightness of the surrounding light, the
OPC sensor might not operate if the adjustment range is
small.
•
•
“Power Saving” does not function when you set “AV MODE”
to “DYNAMIC (Fixed)”.
When “OPC” is set to “On” or “On:Display” while “Power
Saving” is set to “Standard” or “Advanced”, the Power Saving
leaf icon appears to the left of “OPC” in the Picture menu
screen.
When “OPC” is set to “Off” while “Power Saving” is set
to “Standard” or “Advanced”, the Power Saving leaf icon
appears to the left of “Backlight” in the Picture menu screen.
•
No Signal Off
When set to"Enable", the power will automatically shut
down if there is no signal for 15 minutes.
Audio Menu
You can adjust the sound quality to your preference
with the following settings.
Selected item
Treble
button
button
d
c
• Five minutes before the power shuts down, the remaining
time displays every minute.
• "Disable" is the factory preset value.
For weaker treble For stronger treble
For weaker bass For stronger bass
Decrease audio from Decrease audio from
Bass
• When a TV program finishes, this function may not operate.
Balance
the right speaker the left speaker
No Operation Off
When set to "Enable", the power will automatically shut
down if there is no operation for 3 hours.
• Audio menu is grayed out when Output Select is set to
"Variable".
• For resetting all Audio adjustment items to the factory
• Five minutes before the power shuts down, the remaining
time displays every minute.
• "Disable" is the factory preset value.
preset values, press
/
to select "Reset", press ENTER,
a b
press
/
to select "Yes", and then press ENTER.
c d
19
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Antenna Setup - DIGITAL
Setup Menu
EZ Setup
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna Setup -
DIGITAL" screen. If necessary, adjust the direction of
the antenna to obtain the maximum signal strength.
Signal Strength: The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel.
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV.
•
•
If you select "Home", AV MODE is set to "STANDARD".
If you select "Store", AV MODE is set to "DYNAMIC (Fixed)".
If there is no operation for 30 minutes, AV MODE will return
to "DYNAMIC (Fixed)" automatically, regardless of previous
changes to the AV MODE settings.
Channel Strength: Input the 2-digit channel number
to check the signal strength of the selected channel.
Make sure the signal is strong enough for each
channel.
•
This function is available for DIGITAL (Air) only.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
Input Skip
This setting allows you to skip the HDMI or PC-IN
Input ("Input 4 (PC)", "Input 5 (HDMI)", "Input 6 (HDMI)",
"Input 7 (HDMI)" and "Input 8 (HDMI)") on the Input
Selection operation.
• See "Initial Setup" on page 12 for setting each item.
• If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Yes: Skips the input.
No: Does not skip input.
Input Label
Lets you set the input terminal displayed when using
the INPUT SOURCE menu or channel display. Press
CH Setup
If initial setup does not memorize all the channels in
your region, follow the instructions below to manually
memorize the channels.
/
/
/
to select the new name for the input
a b c d
mode.
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
CH Memory: You can select the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable).
On: Skips channels. (Channel selection disabled using CH
U/V.)
Off: Does not skip channels. (Channel selection enabled using
CHU/V.)
• You cannot change labels if the INPUT SOURCE is TV.
Input Signal
(for Analog PC Input Mode Only)
Some input signals may have to be registered manually
to display properly. The pair of input signals (resolutions)
in the list below is not distinguishable when received.
In such a case, you have to set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
Remove Scrambled CH: This function makes the TV
look for and then delete digital cable channels that
are scrambled and so unavailable in the set area. The
process may take more than 20 minutes.
Yes: Starts to remove scrambled channels.
1024 x 768
1360 x 768
• You can only select the "Input Signal" on the Setup menu
when receiving one of the 2 input signals listed above.
No: This function does not work.
Auto Sync.
• See "Initial Setup" on page 12 for setting each item.
• If no channel is found, confirm the type of connection made
with your TV and try channel search again.
• If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
(for Analog PC Input Mode Only)
For automatically adjusting the PC image.
Yes: Auto Sync. starts and "Now adjusting the image."
displays.
No: This function does not work.
• When Auto Sync. is successful, "Completed" displays. If
not, Auto Sync. failed.
• Auto Sync. may fail even if "Completed" displays.
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing Auto Sync.
• Be sure to connect the PC to the TV and switch it on before
starting Auto Sync.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Fine Sync.
Reset
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
"Return to the factory preset values" displays on the
screen.
1
H-Pos.: Centers the image by moving it to the left or
right.
• If you have already set the Secret No., input the 4-digit
secret number here.
V-Pos.: Centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
Select "Yes".
2
3
• "Now, TV will restart automatically. OK?" displays on the
screen.
Select "Yes".
• "Now initializing..." displays on the screen and blinks.
After the reset has been completed, the power shuts off
and then comes back on. The screen will have returned
to its original settings.
• For resetting all Fine Sync. adjustment items to the factory
preset values, press
ENTER.
/
to select "Reset", and then press
a b
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
• The Channel Setup settings will not be changed.
• The Language settings will not be changed.
• The Secret number settings will not be changed.
• The TV Location Settings will not be changed.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
Parental CTRL
(Parental Control Setting)
Position
Secret No.
For adjusting a picture's horizontal and vertical
position.
Allows you to use a secret number to protect certain
settings from being accidentally changed.
H-Pos.: Centers the image by moving it to the left or
right.
IMPORTANT:
V-Pos.: Centers the image by moving it up or down.
Three conditions must be met to enable the V-Chip (see
pages 21 to 23):
1. Secret No. is registered.
• The “V-Chip (DTV Only)” will only be selectable when
a new rating system can be downloaded via digital
broadcasting in the U.S.
• For resetting adjustments to the factory preset values,
press
/
to select "Reset", and then press ENTER.
a b
• When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
2. V-Chip/V-Chip (DTV Only) settings have been made.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
3.
"
Status
"
is set to "On".
• Adjustments are stored separately according to input
source.
New Secret No.
■
You can set and change the secret number by using 0–9.
Input Secret No.: When you change the secret number,
enter the old 4-digit secret number here. The cursor
moves to "New Secret No.".
Language
You can also select a language from the Setup menu.
Select from among 3 languages: English, French and
Spanish.
New Secret No.: When you set the new secret number,
enter the new 4-digit secret number here. The cursor
moves to "Reconfirm".
Reconfirm: Enter the same 4-digit number you set in
"New Secret No.".
■
Secret No. Clear
You can clear your secret number.
Yes: Your secret number is cleared.
No: Your secret number is not cleared.
• As a precautionary measure, make a note of your secret
number and keep it in a familiar place.
• If the secret number is cleared, the Status setting
automatically sets to "Off". "V-Chip" and "Status" will not be
selectable from the menu.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Status
■ TV Parental Guidelines
Example
MPAA
Used to enable or disable the parental control function.
This function will not be selectable from the menu if
you do not first configure your secret number.
On: Enables Parental CTRL
TV Guidelines
TV-Y
Can. English Ratings
Can. French Ratings
TV-Y7
TV-G
D
L
Off: Disables Parental CTRL.
TV-PG
TV-14
TV-MA
NONE
S
V-Chip
V
FV
V-CHIP is an electronic filtering device built into your
TV. This tool gives parents a great degree of control
over broadcasts accessed by their children. It allows
parents to select programs judged suitable for child
viewing while blocking ones judged not suitable. It
does so automatically once you activate the V-CHIP
feature in your TV. "V-Chip" and "Status" will not be
selectable from the menu if you do not first configure
your secret number.
Press
/
to adjust the item to your desired position.
" indicates the item is blocked. Press MENU to exit.
a b
"
Suggested age
TV-Y: All children.
TV-Y7: Directed to older children.
TV-G: General audience.
TV-PG: Parental Guidance suggested.
TV-14: Parents strongly cautioned.
TV-MA: Mature audience only.
• The U.S. has two rating systems for viewing content: TV
Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the
V-CHIP to help parents screen out inappropriate television
shows from their children.
• Movie ratings are used for original movies rated by the
Motion Picture Association of America (MPAA) as watched
on cable TV and not edited for television. The V-CHIP can
also be set to block MPAA-rated movies.
Example
MPAA
TV Guidelines
TV-Y
Can. English Ratings
Can. French Ratings
TV-Y7
TV-G
D
L
• The setting automatically enters "Block" for any ratings
below your selection.
• If Status is not set to "On", the configuration settings will
not work.
TV-PG
TV-14
TV-MA
NONE
S
V
FV
■
MPAA (Voluntary movie rating system)
Example
When setting an individual content-based rating item:
Press
or ENTER to access blocked content
d
1
2
3
MPAA
items from the currently selected age-based rating
item.
TV Guidelines
G
Can. English Ratings
Can. French Ratings
PG
Press to select an individual item, and then
/
a b
PG-13
R
press ENTER to unblock it (" " is removed). Repeat
the same steps for the other items.
NC-17
X
Press
or RETURN to register after all individual
c
content rating items are set.
NONE
Content
FV: Fantasy violence.
V: Violence.
Press
/
to adjust the item to your desired position.
a b
"
" indicates the item is blocked. Press MENU to exit.
S: Sexual situation.
L: Adult language.
D: Sexually suggestive dialog.
G: General audiences. All ages admitted.
PG: Parental guidance suggested. Some material may not be
suitable for children.
PG-13: Parents strongly cautioned. Some material may be
inappropriate for children under 13.
R: Restricted. Under 17 requires accompanying parent or
adult guardian (age varies in some jurisdictions).
NC-17: No one 17 and under admitted.
Content
S
Rating
FV
V
L
D
TV-Y
TV-Y7
X: X is an older rating that is unified with NC-17 but may be
TV-G
encoded in the data of older movies.
Suggested
age
TV-PG
• Voluntary movie rating system only uses an age-based
rating.
TV-14
TV-MA
: The content rating can be set, but this rating is not
normally broadcast by TV stations.
: Content rating can be set.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Canadian Rating Systems (Canadian English ratings
and Canadian French ratings)
• The TV rating systems in Canada are based on the
Canadian Radio-Television and Telecommunications
Commission (CRTC) policy on violence in television
programming.
• While violence is the most important content element to
be rated, the structure developed takes into consideration
other program content like language, nudity, sexuality and
mature themes.
■ Canadian French Ratings
Example
MPAA
TV Guidelines
E
Can. English Ratings
Can. French Ratings
G
8ans+
13ans+
16ans+
18ans+
NONE
• When setting the V-CHIP on the Canadian system you can
choose either the Canadian English ratings or the Canadian
French ratings.
Press
"
/
to adjust the item to your desired position.
" indicates the item is blocked. Press MENU to exit.
a b
■ Canadian English Ratings
E: Exempt programming.
Example
G: General: All ages and children, contains minimal direct
violence, but may be integrated into the plot in a humorous
or unrealistic manner.
8ans+: General but inadvisable for young children: May
be viewed by a wide public audience, but could contain
scenes disturbing to children under 8 who cannot
distinguish between imaginary and real situations.
Recommended for viewing with parent.
MPAA
E
TV Guidelines
C
Can. English Ratings
Can. French Ratings
C8+
G
PG
14+
18+
NONE
13ans+: Over 13 years: Could contain scenes of frequent
violent scenes and therefore recommended for viewing with
parent.
Press
/
to adjust the item to your desired position.
a b
"
" indicates the item is blocked. Press MENU to exit.
16ans+: Over 16 years: Could contain frequent violent scenes
and intense violence.
18ans+: Over 18 years: Only for adult viewing. Could contain
frequent violent scenes and extreme violence.
E: Exempt: Includes news, sports, documentaries and other
information programming; talk shows, music videos, and
variety programming.
C: Children: Intended for younger children under the age of 8
years. Pays careful attention to themes that could threaten
their sense of security and well-being.
C8+: Children over 8 years old: Contains no portrayal
of violence as the preferred, acceptable, or only way
to resolve conflict; nor encourage children to imitate
dangerous acts which they may see on the screen.
G: General: Considered acceptable for all age groups.
Appropriate viewing for the entire family, contains very little
violence, physical, verbal or emotional.
■ How to temporarily release the V-CHIP BLOCK
When the V-CHIP BLOCK is working and censors a
broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.
Press ENTER while the V-CHIP is working, and
1
2
then the secret number setting menu displays.
Input the 4-digit secret number by using 0–9. At this
time V-CHIP BLOCK temporarily releases.
PG: Parental Guidance: Intended for a general audience, but
may not be suitable for younger children (under the age of 8)
because it could contain controversial themes or issues.
14+: Over 14 years: Could contain themes where violence
is one of the dominant elements of the storyline, but it
must be integral to the development of plot or character.
Language usage could be profane and nudity present
within the context of the theme.
18+: Adults: Intended for viewers 18 years and older and
might contain depictions of violence, which while related to
the development of plot, character or themes, are intended
for adult viewing. Could contain graphic language and
portrayals of sex and nudity.
■ Reactivating the temporarily released V-CHIP
BLOCK
You can reactivate the temporarily released V-CHIP
BLOCK as shown below.
• Select "Status" setting from the Parental CTRL menu to
reactivate BLOCK. (See page 22.)
• Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can.
English Ratings" or "Can. French Ratings") from the
Parental CTRL to reactivate BLOCK. (See pages 22 and
23.)
• Switch off the TV power.
• Performing any of the three above will activate the V-CHIP
BLOCK.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
PC Audio Select
Option Menu
Audio Only
When listening to music from a music program, you
can turn the screen off and enjoy audio only.
On: Audio is output without screen image.
Determines whether the AUDIO terminal is used for
INPUT 4 (PC-IN) or INPUT 6 (HDMI).
Input 4 (PC): Select this item when the audio signal is
input via the INPUT 4 (PC-IN) terminal using an analog
RGB cable.
Input 6 (HDMI): Select this item when the audio signal is
input via the INPUT 6 (HDMI) terminal using an HDMI-
DVI conversion cable.
Off: Both screen images and audio are output.
• The screen image will return to normal when a button
(except those for audio adjustment, such as VOL, MUTE,
SURROUND, AUDIO) is pressed.
• When "PC Audio Select" is set to "Input 6 (HDMI)", sound
will not be produced if you use only an HDMI-certified
cable to connect HDMI-compatible equipment. To produce
sound, you should make an analog audio connection.
• If you want to connect HDMI-compatible equipment using
only an HDMI-certified cable, set "PC Audio Select" to
"Input 4 (PC)".
Input Select
If the image does not come in clearly from the external
equipment connected to INPUT 1 or INPUT 2, you
may need to change the input signal type setting on
the "Input Select" menu.
Output Select
■ INPUT 1
Allows you to select what controls the audio output.
Select the input signal type from the list below:
Fixed: Sound via speaker is adjusted with VOL
on
/
k l
on the TV.
Auto/COMPONENT/VIDEO
the remote control unit or VOL
Sound via the AUDIO OUTPUT terminal is not
adjustable and outputs at a consistent level.
Variable: Sound via the AUDIO OUTPUT terminals is
adjusted with VOL
k l
/
k l
■ INPUT 2
Select the input signal type from the list below:
Auto/COMPONENT/S-TERMINAL
on the remote control unit or
/
VOL
on the TV.
/
k l
Sound via speaker is muted.
• If the selected signal type is incorrect, images are not
displayed at all or are displayed without any color.
• Refer to your external equipment operation manual for the
signal type.
• If you set INPUT 1 or 2 to Auto, the TV will automatically
select the input signal.
• Setting INPUT 1 or 2 signal selection to "Auto" when
other equipment is connected will result in the following
connection priority.
Color System
Select the video signal system compatible with your
equipment from the list below:
Auto/NTSC/PAL-M/PAL-N
• "Color System" can only be set for the INPUT 1 VIDEO,
INPUT 2 S-VIDEO and INPUT 3 VIDEO.
• If you have already set the Secret No., input the 4-digit
secret number here. See page 21 for setting a secret
number.
INPUT 1:
COMPONENT VIDEO
VIDEO
INPUT 2:
1
2
COMPONENT VIDEO
S-VIDEO
1
2
Game Play Time
This function displays the elapsed game time so you do
not lose track of the time. To display the elapsed time,
select "GAME" for the AV MODE before starting the game.
On: The elapsed time is displayed every 30 minutes when
you switch to GAME mode in external input mode.
Off: No adjustment.
HDMI Setup
To watch an HDMI or PC-IN equipment image, select
"INPUT5", "INPUT6", "INPUT7" or "INPUT 8" from
"INPUT SOURCE" menu using INPUT on the remote
control unit or on the TV.
Auto View:
Enable: To use View Mode based on signal
recognition, including an HDMI signal.
Disable: No function.
Operation Lock Out
This function locks the operation buttons on the TV
and the remote control.
Off: No adjustment.
• Refer to your external equipment operation manual for the
signal type.
• When connecting an HDMI-DVI conversion adapter/cable
to the HDMI terminal, the image may not come in clearly.
RC Control Lock: All buttons on the remote control are
locked.
Button Control Lock: All buttons on the TV, except
POWER, are locked.
• To unlock the buttons on the remote control, press MENU
on the TV, and then select "Off" on the MENU screen.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" on the MENU screen.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Caption Setup
Digital Setup
This setting allows you to optimize the settings of
Digital broadcasting.
This function allows you to adjust the closed
caption screen appearance to suit your preference.
You can adjust 7 items: "Caption Size", "Font
Style", "Foreground Color", "Foreground Opacity",
"Background Color", "Background Opacity" and
"Character Edge".
Audio Setup
You can output digital audio to an AV amplifier or
similar device whose DIGITAL AUDIO INPUT terminal
is connected to the DIGITAL AUDIO OUTPUT terminal
on the TV. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
PCM: The optical output terminal outputs audio signal
in PCM form. If your digital audio system does not
support Dolby Digital, select "PCM".
Example:
Selectable items available for "Font Style".
Default: The font specified by broadcasting station or
default font.
Type 0: Proportional font used in the MENU screen.
Type 1: Monospaced with serifs.
Type 2: Proportionally spaced with serifs.
Type 3: Monospaced without serifs.
Type 4: Proportionally spaced without serifs.
Type 5: Casual font type.
Dolby Digital: The optical output terminal outputs audio
signal in Dolby Digital form. It reproduces sound from
surround program of digital.
Type 6: Cursive font type.
Type 7: Small capitals.
Identification
The current version of the TV software is displayed.
• For resetting adjustments to the factory preset values,
Software Update
press
/
to select "Reset", and then press ENTER.
a b
• The default value depends on the broadcasting station.
This function allows software updates by inserting
a USB memory device with the update file into the
SERVICE terminal on the TV.
To check for the availability of a software update, visit
call 1-800-BE-SHARP (800-237-4277).
Digital Caption Info.
(Digital Caption Information)
This function allows viewing of digital closed caption
information for the digital broadcast program being
viewed.
CAUTION
• This list is not displayed for analog broadcasts or external
input audio/video.
• This information is not included in CC1, CC2, Text1, or
Text2, and is not displayed in a list.
• Do not remove the USB memory device or unplug the
AC cord while the software is being updated.
• Be sure to properly follow the whole procedure
described below, step by step. Otherwise, for
example, the TV cannot read the data in the USB
memory device and software updating will fail.
Program Title Display
Select the CH display when changing channels for
digital broadcasting.
Insert the USB memory device with the update file
into the SERVICE terminal on the TV.
1
Yes: "Program Info." displays.
No: "Program Info." does not display.
Favorite CH
(Favorite Channel Setting)
This function allows you to program 4 favorite
channels, in 4 different categories. By setting the
favorite channels in advance, you can select your
favorite channels easily.
To register your favorite channel:
Select "Register" and then press ENTER. Press
d
/
/
/
a b c
to select the position in the category, and then press
Press MENU to display the MENU screen, and
2
ENTER to register.
To delete your favorite channel:
Select "1 Data Clear" and then press ENTER. Press
then press
/
to select “Digital Setup”.
c d
Press
/
to select “Software Update”, and then
a b
3
/
/
/
to select the channel you want to delete, and
a b c d
press ENTER.
then press ENTER. Select "Yes" and then press ENTER.
To delete all the favorite channels, select "All Data Clear".
• If you have already set the Secret No., go to step 4.
Digital Setup
• Before setting the channel, select the channel you want to
register as a favorite channel.
Audio Setup
[PCM]
Identification
Software Update
25
Download from Www.Somanuals.com. All Manuals Search And Download.
On-Screen Display Menu
Input the 4-digit secret number by using 0–9.
Press ENTER to start updating.
4
7
• The screen becomes dark for a while until the update
screen can be displayed. Please wait for the update
screen to appear. Do not unplug the AC cord.
Digital Setup
Secret No.
a
a
a
a
The picture will temporarily go dark until
the Software Update display appears.
Wait several minutes and do not unplug the AC cord.
Press ENTER to start checking the data in the
5
6
USB memory device.
Insert the USB memory device containing
the software update file.
OK
OK
Example
Now updating
“
”
During the data checking, Checking blinks.
Do not unplug AC cord.
Update Version
UXXXXXX2
Now checking the data in the USB memory device.
30%
CAUTION
Checking
• Do not remove the USB memory device or unplug the
AC cord while the software is being updated.
• The current version of the TV software and the version
of the update file on the USB memory device are
displayed. To update the TV software with the update
file, select “Yes”, and then press ENTER.
When the software is successfully updated, a
screen is displayed indicating that the update
process is completed.
After this screen is displayed, the TV automatically
turns off and then turns on again.
8
Example
Software update file is detected
in the USB memory device.
Start update?
Example
Current Version:
Update Version:
UXXXXXX1
UXXXXXX2
Software update is complete.
Yes
No
Update Version
UXXXXXX2
• If the USB memory device is not properly installed or
the correct update file cannot be found on the USB
memory device, an error message is displayed.
• Check the file on the USB memory device, and then
reinsert the USB memory device correctly.
• If the update has failed, check the file in the USB
memory device and try Software Update again.
Failed to complete update.
Retry Software Update.
If system Update fails again,
contact the customer service center.
Software update file is not detected
in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
After the screen shown below is displayed, press
ENTER.
9
OK
System software was
successfully updated.
Remove the USB memory device.
There is more than one software file
in the USB memory device.
OK
Confirm that only the software update file is
in the USB memory device.
Remove the USB memory device.
10
OK
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Problem
Possible Solution
•
No power
•
Check if you pressed POWER on the remote control unit. (See page 12.) If the
indicator on the TV does not light up, press POWER on the TV.
Is the AC cord disconnected? (See page 8.)
•
•
Has the power been turned on? (See page 12.)
•
•
Unit cannot be operated.
•
External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning off the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
Remote control unit does not
operate.
•
•
•
•
Are batteries inserted with polarity (
,
) aligned? (See page 9.)
f
e
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
•
•
Picture is cut off/with sidebar
screen.
•
•
Is the image position correct? (See page 21.)
Are screen mode adjustments such as picture size made correctly? (See page 16.)
Strange color, light color, or color
misalignment
•
•
•
Adjust the picture tone. (See pages 18 and 19.)
Is the room too bright? The picture may look dark in a room that is too bright.
Check the input signal setting. (See page 20.)
•
•
Power is suddenly turned off.
•
•
•
Is the sleep timer set? (See page 13.)
Check the power control settings. (See page 19.)
The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
No picture
•
•
•
•
•
•
Is connection to other components correct? (See page 11.)
Is correct input signal source selected after connection? (See page 24.)
Is the correct input selected? (See page 24.)
Is picture adjustment correct? (See pages 18 and 19.)
Is “On” selected in “Audio Only”? (See page 24.)
Is a non-compatible signal being input? (See page 30.)
•
•
No sound
•
•
•
Is the volume too low? (See page 13.)
Is “Variable” selected in “Output Select”? (See page 24.)
Have you pressed MUTE on the remote control unit? (See page 13.)
The TV sometimes makes a
cracking sound.
•
This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in temperature. This does not affect the TV's
performance.
Troubleshooting-Digital Broadcasting
The error message about reception of broadcast
The example of an error message
Error code
Possible Solution
displayed on a screen
•
Check the antenna cable. Check that the antenna is correctly
setup.
•
•
Failed to receive broadcast.
No broadcast now.
E202
E203
•
Check the broadcast time in the program guide.
Cautions regarding use in high and low temperature environments
•
When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
•
Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature: 4°F to 140°F ( 20°C to 60°C)
f
e
f
e
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
RS-232C Port Specifications
■ PC control of the TV
■ Command format
•
Attach an RS-232C cable cross-type (commercially
available) to the supplied Din/D-Sub RS-232C for the
connections.
Eight ASCII codes
CR
e
C1 C2 C3 C4 P1 P2 P3 P4
Command 4-digits
Return code
Parameter 4-digits
• This operation system should be used by a person who is
accustomed to using computers.
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
■ Communication conditions
Set the RS-232C communication settings on the PC to match
the TV's communication conditions.
The TV's communication settings are as follows:
■ Parameter
Input the parameter values, aligning left, and fill with blank(s)
for the remainder. (Be sure that 4 values are input for the
parameter.)
When the input parameter is not within an adjustable range,
“ERR” returns. (Refer to “Response code format”.)
Any numerical value can replace the “x” on the table.
Baud rate:
Data length:
Parity bit:
9,600 bps
8 bits
None
Stop bit:
Flow control:
1 bit
None
When “?” is input for some
commands, the
0
0
a
?
present setting value
responds.
0
3
0
0
9
■ Communication procedure
Send the control commands from the PC via the RS-232C
?
?
?
?
connector.
■ Response code format
The TV operates according to the received command and
sends a response message to the PC.
Do not send multiple commands at the same time.
Wait until the PC receives the OK response before sending the
next command.
Normal response
Problem response (communication error
or incorrect command)
O
K
E
R
R
Return code (0DH)
Return code (0DH)
■ Command table
• Commands not indicated here are not guaranteed to operate.
CONTROL ITEM
COMMAND PARAMETER
CONTROL CONTENTS
POWER ON COMMAND SETTING
R
S
P
W
0
1
0
1
x
0
*
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Off
On
Power Off
Power On
(Toggle)
The Power On command rejected.
The Power On command accepted.
It shifts to standby.
P
O
W
R
POWER SETTING
Power On
INPUT SELECTION A TOGGLE
TV
INPUT1-8
INPUT SELECTION B INPUT 1
INPUT 2
I
I
I
I
I
T
T
A
N
N
V
G
V
V
P
P
M
D
D
D
1
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT8.
Input terminal number (1–8)
0: Auto, 1: VIDEO, 2: COMPONENT
0: Auto, 2: COMPONENT, 3: S-TERMINAL
*
*
An input change is also included.
2
AV MODE SELECTION
A
D
*
0: (Toggle), 1: STANDARD, 2: MOVIE, 3: GAME, 4: USER,
5: DYNAMIC (Fixed), 6: DYNAMIC, 7: PC
Although it can choose now, it is toggle operation in inside.
VOLUME
V
H
V
C
P
O
P
P
L
H
I
L
O
O
C
S
D
M
S
S
K
E
*
*
*
*
*
*
*
*
_
*
_
_
_
_
_
_
Volume (0–60)
H-POSITION
V-POSITION
CLOCK
The screen position variable ranges depend on the View Mode or the
signal type. The ranges can be seen on the position-setting screen.
POSITION
*
*
*
_
*
*
*
_
Only PC mode. (0–180)
Only PC mode. (0–40)
0: (Toggle) [AV], 1: Side Bar [AV], 2: S.Stretch [AV]
3: Zoom [AV], 4: Stretch [AV], 5: Normal [PC]
6: Zoom [PC], 7: Stretch [PC],
PHASE
VIEW MODE
W
E
0: Although it can choose now, it is toggle operation in inside.
1: Only available when 4:3 signal is being input.
5, 6: Only available when 4:3 signal is being input.
8: [PC] Available except when UXGA is being input.
[AV] Only available when 1080i/p is being input.
9: Only available when 720p is being input.
8: Dot by Dot [PC] [AV], 9: Full Screen [AV]
MUTE
M
A
U
C
C
F
T
S
H
T
E
U
A
*
*
_
_
_
_
_
_
_
_
_
_
_
_
0: (Toggle), 1: On, 2: Off
0: (Toggle), 1: On, 2: Off
(Toggle)
0: Off, 1: OFF TIMER – 30 MIN., 2: OFF TIMER – 60 MIN.,
3: OFF TIMER – 90 MIN., 4: OFF TIMER – 120 MIN.
SURROUND
AUDIO SELECTION
SLEEP TIMER
A
x
*
O
M
CHANNEL
DIRECT
CHANNEL
(ANALOG)
D
C
C
H
*
*
*
_
The channel number of TV
(1–135)
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
In Cable, 1–135ch is effective.
DIRECT
CHANNEL
(DIGITAL)
D
D
A
C
2
2
P
U
*
*
*
*
*
*
*
_
(0100-9999)
(1-999)
DIGITAL Air (Two-Part numbers, 2-digit plus 2-digit)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
Front half of DIGITAL CABLE CHANNEL NO. (Designate major channel)
DIGITAL Cable (Two-Part numbers, 3-digit plus 3-digit)
D
C
2
L
*
*
*
_
(0-999)
Rear half of DIGITAL CABLE CHANNEL NO. (Designate minor channel)
D
D
C
C
C
C
C
H
H
L
1
1
U
D
C
0
1
P
W
P
*
*
x
x
x
*
*
_
_
_
*
*
_
_
_
*
*
_
_
_
(0-9999)
(0-6383)
The channel number of TV b1
The channel number of TV a1
(Toggle)
DIGITAL Cable (One-Part numbers, 5-digit, less than 10,000)
DIGITAL Cable (One-Part numbers, 5-digit, more than 10,000)
If it is not TV display, it will input-switch to TV. (same function as CHU)
If it is not TV display, it will input-switch to TV. (same function as CHV)
Toggle operation of a closed caption.
CH UP
CH DOWN
CC
•
•
•
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
Any numerical value can replace the “x” on the table.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Specifications
Item
LCD panel
Model: LC-52SB55U
52o screen size class Advanced Super View & BLACK TFT LCD
1
(Diagonal Measurement :
32o)
52
/
Resolution
2,073,600 pixels (1,920 g 1,080)
American TV Standard ATSC/NTSC System
VHF 2-13ch, UHF 14-69ch
TV-standard (CCIR)
VHF/UHF
CATV
1-135ch (non-scrambled channel only)
TV
Function
Receiving
Channel
Digital Terrestrial
Broadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)
1-135ch (non-scrambled channel only)
Audio multiplex
BTSC System
Backlight
Audio out
60,000 hours (in default “STANDARD” mode)
10W g 2
INPUT 1
INPUT 2
INPUT 4
INPUT 6
AV in, COMPONENT in
COMPONENT in, S-VIDEO in
15-pin mini D-sub female connector, Audio in (Ø 3.5 mm jack)
HDMI in with HDCP, Audio in (Ø 3.5 mm jack)
HDMI in with HDCP
INPUT 7
Rear
INPUT 8
HDMI in with HDCP
Terminals
ANT/CABLE
AUDIO
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
Audio in (Ø 3.5 mm jack)
DIGITAL AUDIO OUTPUT Optical Digital audio output g 1 (PCM/Dolby Digital)
OUTPUT
INPUT 3
Audio out
AV in
Side INPUT 5
SERVICE
HDMI in with HDCP
Software update
English/French/Spanish
OSD language
AC 120 V, 60 Hz (FOR NORTH AMERICA)
AC 110-240 V, 50/60 Hz (FOR OTHERS)
Power Requirement
Power Consumption
285 W (0.4 W Standby with AC 120 V)
60.6 lbs./27.5 kg
TV + stand
TV only
Weight
52.9 lbs./24.0 kg
TV + stand
TV only
49 19
49 19
/
/
64 g 33 25
/
/
32 g 13 1/2 inch
32 g 3 43
64 inch
Dimension*2
(W g H g D)
64 g 31 11
/
Operating temperature
e32°F to e104°F (0°C to e40°C)
*1
*2
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the Spanish operation manual.
•
As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
Part name
Model number
Optional Accessory
The listed optional accessory is available for the Liquid
Wall mount bracket
AN-52AG4
Crystal Television. Please purchase it at your nearest shop.
•
Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 20 to set PC input signals.
PC
Resolution
720 x 400
Horizontal Frequency
Vertical Frequency
VESA Standard
31.5 kHz
70 Hz
*
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
64.0 kHz
65.3 kHz
75.0 kHz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
O
O
O
O
O
O
O
O
O
O
O
O
O
O
VGA
640 x 480
800 x 600
1024 x 768
*
*
SVGA
XGA
PC
*
*
WXGA
SXGA
SXGA+
UXGA
1360 x 768
1280 x 1024
1400 x 1050
1600 x 1200
*
*These 6 formats are not supported by the analog RGB terminal.
DDC is a registered trademark of Video Electronics Standards Association.
VGA and XGA are registered trademarks of International Business Machines Corp.
Information on the Software License for This Product
■ Software composition
The software included in this product is comprised of various software components whose individual copyrights
are held by SHARP or by third parties.
■ Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that were
developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties,
and other relevant laws. This product also makes use of freely distributed software and software components
whose copyrights are held by third parties. These include software components covered by a GNU General Public
License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license agreement.
■ Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
■ Acknowledgements
The following open source software components are included in this product:
• linux kernel/busybox/uClibc/zlib/libpng/libjpeg
CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number using the following procedure.
Select an item from the list below to display the secret number input screen. (For operating the on-screen
display menu, see page 17.)
1
• “EZ Setup”, “CH Setup”, “Parental CTRL” or “Reset” on the Setup menu.
• “Color System” on the Option menu.
• “Software Update” on the Digital Setup menu.
Press and hold both CHU and VOLk on the TV simultaneously until the message appears on the screen.
2
The secret number is
.
•
As a precautionary measure, make a note of your secret number above, cut it from this manual, and keep it in a safe place.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely
for the non-commercial, household use of the Product by consumers in their home or residence. If you intend to or already use this Product
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may
vary. Please contact 1-888-GO-SHARP for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of
purchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. No other representations or promises made by anyone are
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.
Model Specific Section
Your Product Model Number & Description:
LC-52SB55U LCD Color Television
(Be sure to have this information available when you need service for your
Product.)
Warranty Period for this Product:
One (1) year parts, 90 days labor from the date of purchase.
Additional Exclusions from
Warranty Coverage (if any):
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any complex or non-standard installation,
mounting or other encumbrance which would unreasonably interfere with
servicing the Product. The Servicer will remount the Product after service,
provided that such remounting is not into a complex or non-standard installa-
tion. Any additional labor and materials required to remove and/or reinstall a
Product above and beyond the foregoing are not covered by this warranty,
may result in additional charges and are the responsibility of the consumer.
Image Retention resulting from
a
fixed image being displayed for long
periods of time is not covered by this Limited Warranty (see Operation
Manual on how to prevent this).
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, please call Sharp toll free
at 1-800-BE-SHARP.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain in home service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer’s facility and return the set to you once
completed. Be sure to have Proof of Purchase available.
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
SHARP CORPORATION
31
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|