MODEL
UX-P115
FACSIMILE
OPERATION MANUAL
1. Installation
2. Sending Faxes
3. Receiving Faxes
4. Making Copies
5. Special Functions
6. Printing Lists
7. Maintenance
8. Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Welcome, and thank you for
choosing a Sharp fax
machine! The features and
specifications of your new
Sharp fax are shown below.
Automatic dialing
Imaging film
30 numbers
Initial starter roll (included with machine):
32 ft. (10 m) (approx. 30 letter-size pages)
Replacement roll (not included):
UX-5CR 164 ft. (50 m) (one roll yields
approx. 150 letter-size pages)
Memory size*
Modem speed
448 KB (approx. 24 average pages)
9,600 bps with automatic fallback to lower
speeds.
Transmission time*
Resolution
Approx. 15 seconds
Horizontal: 203 pels/inch (8 pels/mm)
Vertical:
Standard: 98 lines/inch (3.85 lines/mm)
Fine /Halftone:
196 lines/inch (7.7 lines/mm)
Super fine:
391 lines/inch (15.4 lines/mm)
Automatic document
feeder
10 pages max. (letter/A4, 20 lb paper)
Recording system
Halftone (grayscale)
Compression scheme
Display
Thermal transfer recording
64 levels
MR, MH, Sharp(H2)
16-digit LCD display
Applicable telephone line Public switched telephone network
*Based on Sharp Standard Chart at standard resolution in Sharp special mode, excluding
time for protocol signals (i.e., ITU-T phase C time only).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper tray capacity
Letter: Approx. 50 sheets (20-lb. copier paper
at room temperature; maximum stack height
should not be higher than the line on the tray)
Legal: 5 sheets
Recommended paper weight is 20-lb. Copy
Bond
Compatibility
ITU-T (CCITT) G3 mode
Input document size
Automatic feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 11" (140 to 279 mm)
Manual feeding:
Width: 5.8 to 8.5" (148 to 216 mm)
Length: 5.5 to 23.6" (140 to 600 mm)
Effective scanning width 8.3" (210 mm) max.
Effective printing width
Contrast control
8.3" (210 mm) max.
Automatic/Dark selectable
TEL/FAX
Reception modes
Copy function
Single / Multi (99 copies/page)
Yes (cannot be used if power fails)
120 V AC, 60 Hz
Telephone function
Power requirements
Operating temperature
Humidity
41 - 95 °F (5 - 35°C)
25 - 85 % RH
Power consumption
Standby: 3.6 W
Maximum: 100 W
Dimensions (without
attachments)
Width: 12.9" (327 mm)
Depth: 7.6" (193 mm)
Height: 6.4" (163 mm)
Weight (without
Approx. 6.2 lbs. (2.8 kg)
attachments)
As a part of our policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice. The
performance specification figures indicated are nominal values of production units. There
may be some deviations from these values in individual units.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety information
Do not disassemble this machine or attempt any procedures not described in this
manual. Refer all servicing to qualified service personnel.
Do not install or use the machine near water, or when you are wet. For example, do
not use the machine near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement, or near a swimming pool. Take care not to spill any liquids on the
machine.
Unplug the machine from the power outlet and telephone jack and consult a
qualified service representative if any of the following situations occur:
- Liquid has been spilled into the machine or the machine has been
exposed to rain or water.
- The machine produces odors, smoke, or unusual noises.
- The power cord is frayed or damaged.
- The machine has been dropped or the housing damaged.
Do not allow anything to rest on the power cord, and do not install the machine
where people may walk on the power cord.
This machine must only be connected to a 120 V, 60 Hz, grounded (3-prong) outlet.
Connecting it to any other kind of outlet will damage the machine and invalidate the
warranty.
Never insert objects of any kind into slots or openings on the machine. This could
create a risk of fire or electric shock. If an object falls into the machine that you
cannot remove, unplug the machine and consult a qualified service representative.
Do not place this machine on an unstable cart, stand or table. The machine could be
seriously damaged if it falls.
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed
for wet locations.
Never touch bare telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm.
There may be a remote risk of electric shock from lightning.
Do not use a telephone to report a gas leak in the vicinity of the leak.
The power outlet must be installed near the equipment and must be easily
accessible.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
A Look at the Operation Panel
6
8
1. Installation
Unpacking Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Loading the Imaging Film . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Loading Printing Paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Entering Your Name and Fax Number . . . . . . . . . . . . . . . . . . . . . . . 16
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setting the Reception Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2. Sending Faxes
23
Transmittable Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Loading the Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjusting the Resolution and Contrast . . . . . . . . . . . . . . . . . . . . . . . 25
Sending a Fax by Normal Dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Sending a Fax by Automatic Dialing. . . . . . . . . . . . . . . . . . . . . . . . . 28
Sending a Fax From Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3. Receiving Faxes
40
Using FAX Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using TEL Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Optional Reception Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Substitute Reception to Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4. Making Copies
47
5. Special Functions
49
Caller ID (Requires Subscription to Service) . . . . . . . . . . . . . . . . . . 49
Distinctive Ring (Requires Subscription to Service) . . . . . . . . . . . . . 54
Blocking Reception of Unwanted Faxes. . . . . . . . . . . . . . . . . . . . . . 56
Polling (Requesting a Fax Transmission). . . . . . . . . . . . . . . . . . . . . 57
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
6. Printing Lists
7. Maintenance
8. Troubleshooting
58
61
64
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Messages and Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Ordering Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
FCC Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Quick Reference Guide
Guía de referencia rápida
Index
77
78
79
5
Download from Www.Somanuals.com. All Manuals Search And Download.
A Look at the Operation Panel
1
2
3
4
5
6
7
8
9
ABC
JKL
TUV
DEF
RESOLUTION/
SPEAKER
RECEPTION MODE
TEL FAX
1
4
2
5
8
0
3
6
GHI
MNO
STOP
FLASH
POLL
HOLD
PQRS
WXYZ
COPY/HELP
7
9
Z
A
SPEED
START/MEMORY
FUNCTION
REDIAL
13
14
15
10 11
12
SPEAKER key
1
2
Press this key to listen to the line and fax tones through the speaker when
faxing a document (page 27).
Note: This is not a speakerphone. You must pick up the handset to talk with
the other party.
RESOLUTION / RECEPTION MODE key
When a document is in the feeder, press this key to adjust the resolution for
faxing or copying (page 25). At any other time, press this key to select the
reception mode (an arrow in the display will point to the currently selected
reception mode; page 20).
FLASH key
3
4
5
This key is used for Call Waiting and other special services that require
subscription from your phone company. Your phone company will provide you
with details on how to use the key.
POLL key
Press this key after dialing another fax machine to receive a document
(previously loaded in the other machine’s feeder) without assistance from the
operator of the other machine (page 57).
HOLD key
Press this key to put the other party on hold during a phone conversation
(page 43).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Display
6
7
This displays messages and prompts to help you operate the machine.
UP and DOWN arrow keys
Enlarge/reduce setting: When making a copy of a document, press these
keys to select an enlarge/reduce setting (page 47).
Volume setting: When a document is not in the feeder, press these keys to
change the handset volume when the handset is lifted, the speaker volume
when the SPEAKER key has been pressed, or the ringer volume at any other
time (page 21).
FUNCTION key settings: Press these keys after pressing the FUNCTION
key to scroll through the FUNCTION MODE settings.
Number keys
8
Use these keys to dial numbers, and enter numbers and letters when storing
auto-dial numbers.
Panel release
Press this release to open the operation panel.
9
STOP key
10
11
Press this key to cancel an operation before it is completed.
COPY/HELP key
When a document is in the feeder, press this key to make a copy of a
document (page 47). At any other time, press this key to print out the Help
List, a quick reference guide to the operation of your fax machine.
START/MEMORY key
Press this key after dialing to begin fax transmission (page 27). Press this key
before dialing to send a fax through memory (page 37).
12
13
14
SPEED key
Press this key to dial a fax or voice number using an abbreviated 2-digit
Speed Dial number (pages 29 and 33).
Left and right arrow keys
Auto-dial numbers: When sending a fax or making a phone call, press these
keys to scroll through your auto-dial numbers (page 34), the “REVIEW
CALLS” list (only available if you have Caller ID; page 51), and the last
number dialed (redial; page 36).
FUNCTION key settings: Press the right arrow key after scrolling with the up
and down arrow keys to select a FUNCTION key setting.
FUNCTION key
15
Press this key followed by the arrow keys to select special functions and
settings.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Installation
Unpacking Checklist
Before setting up,
make sure you
have all of the
If any are missing,
contact your
dealer or retailer.
following items.
Operation
manual
Gears (2)
Paper tray
Handset
Paper tray
extension
Telephone
line cord
Imaging film
(initial starter roll)
Handset cord
Points to keep in mind when setting up
Do not place the
machine near
heaters or air
conditioners.
Do not place the
machine in direct
sunlight.
Keep dust away from Keep the area
the machine.
around the
machine clear.
About condensation
If the machine is moved from a cold to a warm place, it is possible that
condensation may form on the scanning glass, preventing proper scanning of
documents for transmission. To remove the condensation, turn on the power
and wait approximately two hours before using the machine.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connections
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦ The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset
cord goes into the jack
marked with a handset
symbol on the side of
the machine!
Use the handset to make ordinary phone calls,
or to transmit and receive faxes manually.
Connecting the power cord
Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet.
Caution!
Do not plug the power cord into any other kind of outlet. This will damage the
machine and is not covered under the warranty.
The machine does not
have a power on/off
switch, so the power is
turned on and off by
simply plugging in or
unplugging the power
cord.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting the telephone line cord
Insert one end of the line cord into the jack on the back of the machine
marked TEL. LINE. Insert the other end into a standard (RJ11C) single-line
wall telephone jack.
TEL.LINE
Setting the dial mode
The fax machine is set for tone dialing. If you are on a pulse dial line, you must
set the fax machine for pulse dialing. Press the keys on the operation panel as
follows:
Display:
FUNCTION
1 Press
once and
once.
OPTION SETTING
2 Press
3 Press
once and
twice.
DIAL MODE
1=TONE, 2=PULSE
once.
The display briefly shows
your selection, then:
4 Select the dial mode:
TONE:
PULSE:
1
2
DISTINCTIVE
STOP
5 Press
to exit.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Comments:
♦ The fax machine is not designed for use on a line which has call waiting,
call forwarding, or certain other special services offered by your telephone
company. If you attempt to use the fax machine in conjunction with any of
these services, you may experience errors during transmission and
reception of facsimile messages.
♦ The fax machine is not compatible with digital telephone systems.
♦ If your area experiences a high incidence of lightning or power surges, we
recommend that you install surge protectors for the power and telephone
lines. Surge protectors can be purchased at most telephone specialty
stores.
Attach the paper tray and paper tray extension
Attach the paper tray.
Attach the paper tray extension.
Insert horizontally
and rotate up
Click!
Note: The paper tray extension has a top side
and a bottom side. If you cannot insert the
tabs into the holes, turn the support over.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Imaging Film
Loading the Imaging Film
Your fax uses a roll of imaging film to create printed text and images. The print
head in the fax applies heat to the imaging film to transfer ink to the paper.
Follow the steps below to load or replace the film.
When replacing the film,
The initial starter roll of
use a roll of Sharp UX-
5CR imaging film. One
imaging film included with
your fax can print about
roll can print about 150
30 letter-size pages.
letter-size pages.
Use only Sharp Genuine
Supplies with this logo:
1 Remove the paper from the paper tray
and open the operation panel (press
➊).
2
If you are loading the imaging film for
the first time, go to Step 4.
1
2 Remove the used film and
empty spool.
3 Remove the two green gears from the
spools.
DO NOT DISCARD THE TWO GREEN
GEARS!
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Imaging Film
4 Remove the new roll of imaging film
from its packaging.
• Cut the band that holds the rolls
together.
5 Insert the green gears.
1 slot
Make sure the
gears fit into the
slots in the ends
of the rolls.
2 slots
Fit ends of rolls
onto hubs
6 Insert the film into the print
compartment.
Thick roll
to rear
7 Rotate the front gear as shown until
the film is taut.
8 Close the operation panel (press down
on both sides to make sure it clicks
into place).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
Loading Printing Paper
You can load letter or legal size paper in the paper tray. Recommended paper
weight is 20-lb. Copy Bond. The maximum number of sheets is as follows:
Letter size: Approx. 50 sheets (20-Ib. copier paper at room temperature;
maximum stack height should not be higher than the line on the
tray)
Legal size: 5 sheets
1 Fan the paper, and then tap the edge
against a flat surface to even the stack.
Make sure the stack edges are even.
2 Insert the stack of paper into the tray, PRINT SIDE DOWN.
• If paper remains in the tray, take it out and combine it into a single stack
with the new paper.
• Be sure to load the paper so that printing takes place on the print side of
the paper. Printing on the reverse side may result in poor print quality.
• GENTLY LOAD PAPER INTO THE PAPER TRAY.
• DO NOT FORCE IT DOWN INTO THE FEED SLOT.
The stack
should not
be higher
than this line
Note: Do not use paper that has already been printed on, or paper that is curled.
Note: If at any time the display shows the
alternating messages at right, check the printing
ADD PAPER &
paper. If the tray is empty, add paper. If there is
paper in the tray, take it out and then reinsert it.
PRESS START KEY
START/MEMORY
When you are finished, press
.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading Printing Paper
Setting the paper size
The fax has been set at the factory to scale received faxes to letter size paper.
If you loaded legal paper, you must change the paper size setting to LEGAL.
FUNCTION
Display:
OPTION SETTING
1 Press
2 Press
3 Press
once and
once.
once and
twice.
PAPER SIZE SET
1=LETTER,2=LEGAL
once.
The display briefly shows
your selection, then:
4 Select the paper size:
LETTER: LEGAL:
COPY CUT-OFF
1
2
STOP
5 Press
to return to the date and time display.
Print contrast setting
Your fax has been set at the factory to print at normal contrast. If desired, you
can change the print contrast setting to LIGHT.
FUNCTION
Display:
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
PRINT CONTRAST
once and
3 times.
1:NORMAL
once.
The display briefly shows
your selection, then:
4 Select the print contrast:
NORMAL: LIGHT:
1
2
PAPER SIZE SET
STOP
5 Press
to return to the date and time display.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
Entering Your Name and Fax Number
Before you can begin sending
Once you enter this
faxes, you must enter your
information, it will
name and fax (telephone)
automatically appear at
number. You also need to set
the top of each fax page
the date and time.
you send.
Important!
FCC regurations require that your name, telephone/fax number, and the date and
time appear on each fax message you send. Enter your name and fax number
here and set the date and time as explained in the following section to have the fax
machine include this information automatically at the top of your fax messages.
STOP
1
4
7
2
5
8
0
3
6
9
FUNCTION
START/MEMORY
FUNCTION
Display:
1 Press
2 Press
3 Press
once and
twice.
ENTRY MODE
once.
OWN NUMBER SET
ENTER FAX #
once.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering Your Name and Fax Number
4 Enter your fax number by pressing the number keys (max. 20 digits).
• To insert a space between digits, press
.
SPEAKER
• To clear a mistake, press
.
START/MEMORY
5 Press
to enter the fax number in memory.
6 Enter your name by pressing number keys for each letter as shown in
the chart below. Up to 24 characters can be entered.
Example: SHARP = 7777 44 2 777
7
G =
H =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
SPEAKER
♦ To clear a mistake, press
.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
repeatedly: . / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
Display:
START/MEMORY
7 Press
DATE&TIME SET
STOP
8 Press
to return to the date and time display.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
Setting the Date and Time
The date and time appear
in the display and are
printed at the top of every
page you fax. Set the date
and time as shown below.
STOP
1
4
7
2
5
8
0
3
6
9
FUNCTION
START/MEMORY
FUNCTION
Display:
ENTRY MODE
1 Press
2 Press
3 Press
once and
twice.
once and
once.
once.
DATE&TIME SET
DATE 08-15-2004
The currently set date
appears (example):
4 Enter a two-digit number for the month (“01” for January, “02” for
February, “12” for December, etc.).
Example: January
0
1
DATE 01-15-2004
• To correct a mistake, press
to move the cursor back to the mistake and
then enter the correct number.
5 Enter a two-digit number for the day (“01” to “31”).
th
Example: the 5
0
5
DATE 01-05-2004
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Date and Time
The currently set time
appears (example):
6 Enter the year (four digits).
Example: 2004
2
0
0
4
TIME 12:19 PM
7 Enter a two-digit number for the hour (“01” to “12”) and a two-digit
number for the minute (“00” to “59”).
TIME 09:25 PM
Example: 9:25
0
9
2
5
8 Press
9 Press
to select A.M. or
to select P.M.
START/MEMORY
ANTI JUNK #
to start the clock.
STOP
10 Press
to return to the date and time display.
Daylight Saving Time
If desired, you can set the clock to move forward and backward automatically
at the beginning and end of Daylight Saving Time. Follow these steps:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
DAY LIGHT SAVE
once and
5 times.
once.
1=YES, 2=NO
RECEIVE RATIO
4 Press
5 Press
to select YES, or
to select NO.
1
2
STOP
to return to the date and time display.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Reception Mode
Setting the Reception Mode
Your fax has two modes for receiving incoming faxes:
FAX mode:
Select this mode when you only want to receive faxes on your line. The fax
machine will automatically answer all calls on four rings and receive incoming
faxes.
TEL mode:
Select this mode when you want to receive both phone calls and faxes on the
line connected to the fax machine. All calls, including faxes, must be
answered by picking up the fax machine's handset or an extension phone
connected to the same line.
Setting the reception mode
Make sure a document is not loaded in the document feeder, and then
RESOLUTION/
RECEPTION MODE
press
until the arrow in the display points to the desired mode.
♦ Note: When a document is loaded in the document feeder, pressing
RESOLUTION/
RECEPTION MODE
adjusts the resolution for faxing and copying.
RESOLUTION/
RECEPTION MODE
TEL FAX
TEL FAX
JAN-01 10:30
RESOLUTION/
1
4
7
2
5
8
0
3
6
9
RECEPTION MODE
JAN-01 10:30
For more information on receiving faxes in FAX and TEL modes, see Chapter
3, Receiving Faxes (page 40).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment
Volume Adjustment
You can adjust the volume of the speaker, handset, and ringer using the up
and down arrow keys.
SPEAKER
1
4
7
2
5
8
0
3
6
9
Speaker
1 Press
2 Press
SPEAKER
or
until the display
Display: SPEAKER: HIGH
SPEAKER: MIDDLE
SPEAKER: LOW
shows the desired volume level.
SPEAKER
• Press
speaker.
again to turn off the
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Adjustment
Handset
1 When talking through the handset,
Display:
press
or
until the display
RECEIVER: HIGH
shows the desired volume level.
• Note: The volume reverts to MIDDLE
RECEIVER: MIDDLE
RECEIVER: LOW
each time you replace the handset.
Ringer
1 Press
or
.
Display:
SPEAKER
(Make sure
has not been
RINGER: HIGH
pressed, the handset is not lifted, and a
document is not loaded in the feeder.)
RINGER: MIDDLE
RINGER: LOW
• The ringer will ring once at the selected
level, then the date and time will
reappear in the display.
RINGER: OFF OK ?
2 If you selected RINGER: OFF OK ?,
START/MEMORY
press
.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Sending Faxes
Transmittable Documents
Size and weight
The size and weight of documents that you can load in the document feeder
depend on whether you load one page at a time or several pages at once.
Loading one page at a time:
Loading up to 10 pages at once:
Minimum size
Minimum size
Maximum size
Maximum size
8.5"
(216 mm)
8.5"
(216 mm)
5.8"
(148 mm)
5.8"
(148 mm)
5.5"
(140 mm)
5.5"
(140 mm)
11"
(279 mm)
23.6"
(600 mm)
Minimum weight Maximum weight
Minimum weight Maximum weight
14 lbs.
(52 g/m² )
21.5 lbs.
(80 g/m²)
42 lbs.
(157 g/m²)
14 lbs.
(52 g/m² )
Note: Letters or graphics on the edges of a document will not be scanned.
0.2"(5 mm)
Letters in the
shaded area will
not be scanned.
8.3"(210 mm)
Note: The full width of
documents less than
8.3” (210 mm) wide is
scanned.
0.2"(5 mm)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Document
Other restrictions
♦ The scanner cannot recognize yellow, greenish yellow, or light blue ink.
♦ Ink, glue, and correcting fluid on documents must be dry before they pass
through the document feeder.
♦ All clips, staples, and pins must be removed from documents before loading
in the feeder. If these are not removed, they may damage the machine.
♦ Documents which are patched, taped, torn, smaller than the minimum size,
carbon backed, easily smudged, or have a slippery coated surface should
be photocopied, and the copy loaded in the feeder.
Loading the Document
Up to 10 pages can be placed in the feeder at one time. The pages will
automatically feed into the machine starting from the bottom page.
♦ If you need to send or copy more than 10 pages, place the additional pages
gently and carefully in the feeder just before the last page is scanned. Do
not try to force them in, as this may cause double-feeding or jamming.
♦ If your document consists of several large or thick pages which must be
loaded one at a time, insert each page into the feeder as the previous page
is being scanned. Insert gently to prevent double-feeding.
1 Adjust the document guides to the
width of your document.
2 Insert the document face down in the
document feeder. The top edge of the
document should enter the feeder first.
• READY TO SEND will appear in the
display.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
3 Adjust the resolution and/or contrast settings as explained in
Resolution and Contrast below, then dial the receiving machine as
explained on page 27.
Adjusting the Resolution and Contrast
If desired, you can adjust the resolution and contrast before sending a
document.
The default resolution
setting is STANDARD
and the default contrast
setting is AUTO.
You must adjust the
settings each time
you don’t want to use
the default settings.
Note: The resolution and contrast settings are only effective for sending a
document. They are not effective for receiving a document.
Resolution settings
STANDARD
Use STANDARD for ordinary documents. This
setting gives you the fastest and most
economical transmission.
FINE
Use FINE for documents containing small letters
or fine drawings.
SUPER FINE
HALF TONE
Use SUPER FINE for documents containing
very small letters or very fine drawings.
Use HALF TONE for photographs and
illustrations. The original will be reproduced in
64 shades of gray.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Resolution and Contrast
Contrast settings
AUTO
DARK
Use AUTO for normal documents.
Use DARK for faint documents.
1 Load the document(s).
• The document must be loaded before
the resolution and contrast can be
adjusted.
RESOLUTION/
Display:
RECEPTION MODE
2 Press
one or more times
until the desired resolution and
STANDARD :AUTO
contrast settings appear in the display.
• The first time you move through the list
of resolution settings, the contrast
setting AUTO will appear next to each
resolution setting. The second time you
move through the list, the contrast
setting DARK will appear.
FINE
:AUTO
SUPER FINE :AUTO
HALF TONE :AUTO
STANDARD :DARK
HALF TONE :DARK
Note: In order to transmit in SUPER FINE resolution, the receiving fax machine
must also have that resolution. If it doesn’t, your machine will automatically step
down to the next best available setting.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Normal Dialing
Sending a Fax by Normal Dialing
SPEAKER
With Normal Dialing, you pick up the handset (or press
pressing the number keys.
) and dial by
♦ If a person answers, you can talk with them through the handset before
SPEAKER
sending the fax. (If you pressed
talk.)
, you must pick up the handset to
♦ Normal Dialing allows you to listen to the line and make sure the other fax
machine is responding.
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
SPEAKER
SPEAKER
2 Pick up the handset or press
Listen for the dial tone.
.
or
ABC
DEF
3 Dial the number of the receiving
machine by pressing the number keys.
1
4
2
5
8
0
3
6
GHI
JKL
TUV
MNO
WXYZ
PQRS
7
9
4 Wait for the connection. Depending on the setting of the receiving
machine, you will either hear a fax tone or the other person will answer.
• If the other party answers, ask them to press their Start key (if you pressed
SPEAKER
, pick up the handset to speak with them). This causes the receiving
machine to issue a fax tone.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
5 When you hear the fax tone, press START/MEMORY . Replace the handset.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 59).
Note: If the transmission is unsuccessful and DOCUMENT JAMMED appears
in the display, remove the document as explained on page 71. (This may
occur if the other fax machine doesn’t respond properly when you attempt to
send the document.)
Sending a Fax by Automatic Dialing
You can store up to 30 fax or phone numbers in the machine for automatic
dialing. When you store a number, you select a two-digit Speed Dial number
for it.
SPEED
♦ Auto-dial numbers are dialed by pressing
, entering the two-digit
START/MEMORY
Speed Dial number, and then pressing
.
♦ You can also search for an auto-dial number by pressing
or
.
START/MEMORY
When the desired number appears in the display, press
it.
to dial
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Storing fax and phone numbers for automatic dialing
Display:
FUNCTION
1 Press
once and
once.
<NEW NUMBER>
2 If you know the Speed Dial number that
ENTER FAX #
you want to use, enter that number (for
example, press
for Speed Dial 01).
0
1
Any number from 01 to 30 can
be selected as a Speed Dial
number. The number must be 2
digits long (01, 02, 10, etc.).
Otherwise, press once (the
machine will suggest an available
Speed Dial number at the end of the
storing procedure).
3 Enter the fax or voice number by pressing the number keys.
(Note: A space cannot be entered.)
SPEAKER
• To clear a mistake, press
.
• If a pause is required between any of the digits to access a special service
FUNCTION
or an outside line, press
. The pause appears as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
START/MEMORY
4 Press
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
5 Enter a name by pressing number keys for each letter as shown in the
chart below. Up to 15 characters can be entered. (If you do not wish to
enter a name, go directly to Step 6.)
Example: SHARP = 7777 44 2 777
7
G =
N =
O =
P =
Q =
R =
S =
T =
U =
V =
W =
SPACE =
A =
B =
C =
D =
H =
I =
J =
K =
L =
X =
Y =
Z =
E =
F =
M =
♦ To enter two letters in succession that require the same key, press
after entering the first letter.
♦ To enter a lower case letter, continue pressing the key for the letter until the
lower case letter appears. To enter one of the following symbols, press
or
repeatedly:
. / ! " # $ % & ’ ( ) + + , - : ; < = > ? @ [ ¥ ] ^ _ ' { | } ) (
START/MEMORY
6 Press
.
If you selected a Speed Dial number in Step 2, the display will briefly
show STORED, and then <NEW NUMBER>. Go to Step 7.
If you did not select a Speed Dial number in Step 2, the display will show
the next available Speed Dial number. If that number is acceptable,
START/MEMORY
press
and go to Step 7. If not, enter the desired two digit
number, press START/MEMORY , and go to Step 7.
STOP
7 Return to Step 2 to store another number, or press
the date and time display.
to return to
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Note: The fax machine uses a lithium battery to keep automatic dialing numbers
and other programmed information in memory when the power is turned off.
Battery power is consumed primarily when the power is off. With the power kept
continuously off, the life of the battery is about 5 years. If the battery dies, have
your dealer or retailer replace it. Do not try to replace it yourself.
Editing and clearing auto-dial numbers
If you need to make changes to a previously stored auto-dial number, or clear
a number, follow these steps:
Display:
FUNCTION
1 Press
once and
once.
<NEW NUMBER>
2 Enter the 2-digit Speed Dial number that you wish to edit or clear (for
example, press
), or press
or
until the number
0
1
appears in the display.
3 Press
once.
1=EDIT, 2=CLEAR
4 Select EDIT or CLEAR:
EDIT:
CLEAR:
1
2
• If you selected CLEAR, go to Step 8.
5 If you selected EDIT, make the desired changes to the number.
• Press or to move the cursor to the digit or digits you wish to
change, and then enter the new digit. The new digit will replace the old
digit.
• If you do not wish to change the number, go directly to Step 6.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
START/MEMORY
6 Press
7 Make the desired changes to the name.
• Press
or
to move the cursor to the letter or letters you wish to
change, and then press the appropriate number key repeatedly until the
desired letter appears (see Step 5 on page 30). The new letter will replace
the old letter.
• If you do not wish to change the name, go directly to Step 8.
START/MEMORY
8 Press
STOP
9 Return to Step 2 to edit or clear another number, or press
return to the date and time display.
to
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Dialing an auto-dial number with the SPEED key
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
SPEED
2 Press
press
and then enter the 2-digit Speed Dial number (for example,
).
1
0
3 Check the display. If the name or number shown is correct, press
STOP
START/MEMORY . (If not, press
and repeat Step 2.)
• If the transmission is completed successfully, the machine will beep once.
• If an error occurs, the machine will beep three times and print a Transaction
Report to inform you of the problem (see page 59).
Using a Speed Dial number for a voice call
SPEED
To use a Speed Dial number for a voice call, lift the handset, press
and enter the Speed Dial number.
,
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Searching for an auto-dial number
If you don’t remember the Speed Dial number in which you have stored a full
fax or phone number, follow these steps to search for the number.
1 If you are sending a fax, load the
document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Press
(or
) until the name of the other party appears in the
display (if no name was stored, the number will appear).
3 If you are sending a fax, press START/MEMORY . Dialing and transmission
begins.
• If the transmission is completed successfully, the fax will beep once.
• If an error occurs, the fax will beep three times and print a Transaction
Report to inform you of the problem (see page 59).
If you are making a phone call, lift the handset. Dialing begins. (If you
START/MEMORY
lifted the handset before searching for the number, press
begin dialing.)
to
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Sending a fax by Direct Keypad Dialing
You can also enter a full number with the number keys and then press
START/MEMORY
to begin dialing. You can use this method to dial a full number
when you don't need to speak to the other party before faxing.
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Enter the number of the receiving machine by pressing the number
keys.
• If a pause is required between any of the digits to access a special service
FUNCTION
or an outside line, press
. The pause will appear as a hyphen (two
seconds per pause). Several pauses can be entered in a row.
3 Check the display. If the number of the receiving machine shown is
START/MEMORY
correct, press
.
STOP
• If the number is not correct, press
to backspace and clear one digit
at a time, and then re-enter the correct digit(s).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax by Automatic Dialing
Redial
You can automatically redial the last number dialed. This procedure can to be
used to send a fax or make a phone call.
1 If you are sending a fax, load the
document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
READY TO SEND
2 Press
once. <REDIAL> appears in the display, followed by the last
number dialed. Make sure the number that appears is the number you
wish to dial.
3 If you are sending a fax, press START/MEMORY . Dialing and transmission
begins.
If you are making a phone call, lift the handset. Dialing begins.
Note: If a fax transmission is unsuccessful and DOCUMENT JAMMED
appears in the display, remove the document as explained on page 71. (This
may occur if the other fax machine doesn’t respond properly when you
attempt to send the document.)
Automatic redialing
If you use automatic dialing (including Direct Keypad Dialing) to send a fax
and the line is busy, the fax machine will automatically redial the number. The
fax machine will make three redial attempts at an interval of five minutes.
During this time, RECALLING will appear in the display, followed by a two-digit
number assigned to the fax job. You will not be able to dial any other locations
while the message appears.
STOP
♦ To stop automatic redialing, press
.
♦ Under certain conditions (for example if a person answers the call on a
telephone), automatic redialing may stop before three redialing attempts
are made.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
Sending a Fax From Memory
You can scan a document into the fax’s memory and send the document from
memory. This increases transmission speed and allows you to send a fax to
multiple destinations in a single operation. After transmission, the document is
automatically cleared from memory.
Broadcasting (sending a fax to multiple destinations)
This function allows you to send the same fax to as many as 20 different
locations in just one operation.
♦ When sending to multiple locations, only auto-dial numbers can be used to
dial the numbers of the receiving machines.
1 Load the document(s).
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
START/MEMORY
2 Press
.
3 Select a destination using one of the following methods:
SPEED
Press
and enter a 2-digit Speed Dial number.
Press
(or ) until the name of the number appears in the display
(if no name was stored, the number will appear).
4 Press
to select the number.
5 Repeat Steps 3 and 4 for each of the other locations to which you wish
to send the fax (maximum of 20).
• To check your selected locations, press
to scroll through them. To
STOP
delete a location, scroll to the location and then press
.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
START/MEMORY
6 When you are ready to begin transmission, press
.
• A Transaction Report is automatically printed out after Broadcasting is
completed. Check the "Note" column of the report to see if any of the
locations are marked "Busy" or have a communication error code. If so,
send the document to those locations again.
Memory transmission
You can also send a fax through memory when sending to a single location.
This is convenient when sending to locations where the line is often busy, as it
saves you from waiting to pick up the original document and frees the feeder
for other operations.
To send a fax through memory, load the document, press START/MEMORY , and
then dial using one of the following methods:
START/MEMORY
♦
Press the number keys to enter the fax number and then press
.
START/MEMORY
SPEED
♦ Press
, enter a 2-digit Speed Dial number, and press
repeatedly to select an auto-dial number and then press
once to select the last number dialed and then press
.
START/MEMORY
START/MEMORY
♦
♦
Press
Press
.
.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a Fax From Memory
If the memory becomes full...
If the memory becomes full while the document is being scanned, MEMORY
IS FULL and SEE MANUAL will alternately appear in the display.
START/MEMORY
♦ Press
if you want to transmit the pages which have been
stored up to that point in memory. The remaining pages will be ejected from
the feeder. After transmission, the memory will be cleared and you can
transmit the remaining pages. You will also need to transmit the page which
was being scanned when the memory filled up.
STOP
♦ Press
if you want to cancel the entire transmission.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Receiving Faxes
Using FAX Mode
To select FAX mode, press
RESOLUTION/
RECEPTION MODE
until the arrow
in the display points to FAX.
RESOLUTION/
RECEPTION MODE
TEL FAX
When the reception mode is set to FAX, the fax machine will automatically
answer all calls on four rings and receive incoming faxes.
♦ If you pick up the handset before the machine answers, you can talk to the
other party and/or receive a fax as explained in Using TEL Mode on page
41.
4 rings
Fax reception
Changing the number of rings
If desired, you can change the number of rings on which the fax machine
answers incoming calls in FAX mode. Any number from 2 to 5 can be
selected.
Display:
FUNCTION
1 Press
once and
once.
OPTION SETTING
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
2 Press
3 Press
once.
once.
NUMBER OF RING
ENTER (2-5) (4)
The display briefly shows
your selection, then:
4 Enter the desired number of rings (any
number from 2 to 5).
TRANSACTION
Example: 3 rings
3
STOP
5 Press
to return to the date and time display.
Note: If you are using Distinctive Ring, the fax machine will answer calls after two
rings regardless of the above setting.
Using TEL Mode
To select TEL mode, press
RESOLUTION/
RECEPTION MODE
until the arrow
in the display points to TEL.
RESOLUTION/
TEL FAX
RECEPTION MODE
When the reception mode is set to TEL, you must answer all calls by picking
up the fax machine’s handset or an extension phone connected to the same
line.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
Answering with the fax’s handset
Important: If a document is loaded in the machine’s feeder, remove it before
performing the steps below. (Fax reception is not possible when a document
is in the feeder.)
1 When the fax machine rings, pick up
the handset.
2 If you hear a fax tone, wait until the
Beep
display shows RECEIVING and then
RECEIVING
replace the handset.
If RECEIVING does not appear (or if you have set
the Fax Signal Receive setting to NO), press
START/MEMORY
to begin reception.
3 If the other party first speaks with you
and then wants to send a fax, press
START/MEMORY
RECEIVING
START/MEMORY
after speaking. (Press
before the sender presses their Start
key.)
• When RECEIVING appears in the
display, hang up.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using TEL Mode
Answering on an extension phone connected to the same
line
Important: If a document is loaded in the machine’s feeder, remove it before
performing the steps below. (Fax reception is not possible when a document
is in the feeder.)
1 Answer the extension phone when it
rings.
2 If you hear a soft fax tone, wait until your fax responds (you will hear
pronounced, high-pitched tones), then hang up.
Beep
Pronounced, high-
pitched tones
3 If the fax doesn't respond, or if the other party first talks to you and then
wants to send a fax, set the phone done (do not hang up), walk over to
START/MEMORY
the fax, lift the fax’s handset, and press
.
• The above step is necessary if you have set the Fax Signal Receive setting
to NO.
Putting a call on hold
To put the other party on hold during a phone conversation, press
.
HOLD
When this is done, they cannot hear you. You can put the handset back in the
cradle without breaking the connection. When you are ready to speak with the
other party again, pick up the handset. If you did not put the handset back in
the cradle, press HOLD
again to resume conversation.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
Optional Reception Settings
Fax Signal Receive
Your fax will automatically begin reception if you hear a soft fax tone after
answering a call on your fax or an extension phone. If you use a computer fax
modem to send documents on the same line, you must turn this function off in
order to prevent your fax from mistakenly attempting to receive documents
from the computer fax modem. Follow the steps below to change the setting.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
once and
4 times.
FAX SIGNAL RX
once.
1=YES, 2=NO
The display briefly shows
your selection, then:
4 Press
to turn on the function, or
1
CALLER-ID
to turn it off.
2
STOP
5 Press
to return to the date and time display.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Reception Settings
Reception Ratio
The fax has been set at the factory to automatically reduce the size of
received documents to fit the size of the printing paper. This ensures that data
on the edges of the document are not cut off. If desired, you can turn this
function off and have received documents printed at full size.
♦ If a document is too long to fit on the printing paper, the remainder will be
printed on a second page. In this case, the cut-off point may occur in the
middle of a line.
♦ Automatic reduction may not be possible if the received document is too
large, contains too many fine graphics or images, or is sent at high
resolution. In this case, the remainder of the document will be printed on a
second page.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
once and
4 times.
RECEIVE RATIO
1=AUTO, 2=100%
once.
The display briefly shows
your selection, then:
4 Press
to select AUTO, or
to
1
2
select 100%.
PRINT CONTRAST
STOP
5 Press
to return to the date and time display.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Substitute Reception to Memory
Substitute Reception to Memory
In situations where printing is not possible, such as when your fax runs out of
paper, the imaging film needs replacement, or the paper jams, incoming faxes
will be received to memory.
When you have received a document in memory, FAX RX IN MEMORY will
appear in the display, alternating with ADD PAPER & PRESS START KEY or
CHECK FILM / CHECK COVER / CHECK PAPER JAM. When you add paper
(and press START/MEMORY ), replace the imaging film, or clear the jam, the stored
documents will automatically print out.
♦ If you received documents in memory because the fax ran out of paper, be
sure to add paper which is the same size as the paper previously used. If
not, the document print-out size may not match the size of the printing
paper.
Caution!
When documents are stored in memory, do not turn the power off. This will
erase all of the contents.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Making Copies
Your fax machine can also be used to make copies. Single and multiple copies
(up to 99 per original) can be made, enabling your fax to double as a
convenience office copier.
1 Load the document(s) face down.
(Maximum of 10 pages.)
RESOLUTION/
RECEPTION MODE
• If desired, press
to set the
resolution and/or contrast.
(The default resolution setting for
copying is FINE.)
READY TO SEND
2 If desired, select an enlarge/reduce setting, and/or select the number of
copies per original:
• ENLARGE/REDUCE: Press
or
until the desired setting appears
in the display. Settings are 100%, 125%, 135%, 50%, 73%, 88%, 94%, and
AUTO. (The default setting is 100%.)
Example: Press
twice
RATIO: 125%
• Number of copies per original: Press the number keys to enter a number
from 1 to 99. (The default setting is 1.)
Example: Press
for five copies
5
5
COPY/HELP
3 When you are ready to begin copying, press
If MEMORY IS FULL appears...
.
If the memory becomes full while a document is being scanned, MEMORY IS
FULL and SEE MANUAL will alternately appear in the display and the
document will automatically feed out. This may happen if the resolution is set
to SUPER FINE, or if you selected an enlarge/reduce setting, or if you are
making more than one copy per original. To avoid using memory, use
STANDARD or FINE for the resolution, 100% for the enlarge/reduce setting,
and make only one copy per original.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Copies
Copy Cut-off
When making a copy of a document that is longer than the printing paper, use
the copy cut-off setting to select whether the remaining part of the document
will be cut off or printed on a second page. The initial setting is YES (cut off
the remainder). To change the setting, follow the steps below.
FUNCTION
Display:
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
once and
once.
COPY CUT-OFF
1=YES, 2=NO
once.
The display briefly shows
your selection, then:
4 Press
to set copy cut-off to YES
1
(the remaining part of the document
NUMBER OF RING
will not be printed), or
to set copy
2
cut-off to NO (the remaining part will
be printed on a second page).
STOP
5 Press
to return to the date and time display.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Special Functions
Caller ID (Requires Subscription to Service)
If you subscribe to a caller identification service from your telephone
company, you can set your fax machine to display the name and number of
the caller while the fax rings.
Important:
♦ To use this function, you must subscribe to a caller identification service
from your telephone company. Note that the machine may not be
compatible with some caller identification services.
♦ Area Code mode: This step is needed if your telephone exchange cannot
dial a local phone number (within your calling area code) when the area
code is dialed with the phone number (see Step 5).
Display:
FUNCTION
1 Press
once and
once.
OPTION SETTING
2 Press
3 Press
once and
5 times.
CALLER-ID
once.
1=YES, 2=NO
AREA CODE # MODE
1=SET, 2=CLEAR
4 Press
(YES) to turn on Caller ID.
1
(To turn off Caller ID, press
and go
2
to Step 8.)
5 Press
to select SET.
(To clear a previously set area code,
press and go to Step 8.)
1
ENTER AREA CODE
2
Note: Entering your area code in this step causes it to be automatically removed
from local numbers in the Caller ID list (page 51). This is only required if you need
to eliminate dialing of the area code when dialing a local number from the list.
Example (using the area code “123”): If Step 5 is skipped, the Caller ID display will
show 123-444-1234, and the number that will dial from the Caller ID list is 123-
444-1234. If the area code 123 is entered in Step 5, the Caller ID display will show
444-1234, and the number that will dial from the Caller ID list is 444-1234.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
6 Enter the three digits of your area code.
START/MEMORY
7 Press
8 Press
to store your area code.
DAY LIGHT SAVE
STOP
to return to the date and time display.
How Caller ID operates
When you receive a call, the name and phone number of the caller will
alternately appear in the display, beginning just before the second ring. The
information will continue to be displayed until the line is disconnected.
Note: Some caller ID services may not provide the name of the caller. In this case,
only the phone number will appear.
Display example
JOHN DOE
525-8693
Caller’s name
Caller’s number
Display messages
One of the following messages will appear while the fax rings if caller
information is not available.
NO SERVICE
No caller information was received from your telephone
company. Make sure that the telephone company has
activated your service.
CALLER-ID ERROR Noise on the telephone line prevented reception of
caller information.
OUT OF AREA
The call was made from an area which does not have a
caller identification service, or the caller’s service is not
compatible with that of your local phone company.
PRIVATE CALL
Caller information was not provided by the telephone
company at the caller’s request.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
Viewing the Caller ID list
If you subscribe to a Caller ID service and have turned on the Caller ID
function, your fax machine will keep information on the most recent 30 calls
and faxes you have received. You can view this information, which consists of
the name and number of each caller, in the Caller ID List.
♦ After you have received 30 calls, each new call will delete the oldest call.
♦ All calls will be erased if you unplug the fax or a power failure occurs.
Follow the steps below to view the Caller ID List in the display. If desired, you
can immediately dial a number when it appears.
1 Press
twice.
or
<REVIEW CALLS>
2 Press
to scroll through the list.
3 If you want to dial one of the numbers in the list, scroll through the list
until the number appears in the display.
• Fax: If you want to send a fax, load the
START/MEMORY
document and then press
.
Dialing and transmission begin.
START/MEMORY
Fax:
• Voice call: If you want to make a voice
call, pick up the handset (or press
SPEAKER
). Dialing begins automatically.
Voice
call:
SPEAKER
(If you pressed
, pick up the
handset when the other party answers.)
STOP
4 Press
when you have finished viewing the list.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
To delete calls from the Caller ID list
If you want to delete a single call from the caller list, press
while the call
appears in the display. If you want to delete all calls from the list, hold
down for at least 3 seconds while you are viewing any number in the list.
Priority Call
With Caller ID turned on, you can set your fax to make a special ringing sound
when you receive a call from a designated phone number. This lets you know
immediately who is calling without having to look at the display.
To use this function, enter the desired phone number by following the steps
below (only one phone number can be entered).
FUNCTION
Display:
1 Press
2 Press
3 Press
once and
twice.
ENTRY MODE
PRIORITY #
once and
once.
once.
1=SET, 2=CLEAR
4 Press
to store a number.
1
(To clear a previously stored number, press
and go to Step 6.)
2
5 Enter the number by pressing the number keys (max. 20 digits).
START/MEMORY
OWN NUMBER SET
6 Press
7 Press
to store (or clear) the number.
STOP
to return to the date and time display.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID (Requires Subscription to Service)
Blocking voice calls
With Caller ID turned on, you can use the Anti Junk Fax function described in
Blocking Reception of Unwanted Faxes in this chapter to block voice calls as
well as faxes from your specified Anti Junk Number.
In this case, when a voice call or a fax transmission comes in from the number
you have specified as a "Junk Number", your fax will break the connection as
soon as it receives the calling phone number from the caller ID service (before
the second ring).
To use this function, enter the number that you wish to block as explained in
Blocking Reception of Unwanted Faxes (see page 56). Only one number can
be blocked.
Note: This function cannot be used if you are using the Distinctive Ring function.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Subscription to Service)
Distinctive Ring (Requires Subscription to
Service)
Important:
♦ To use distinctive ring, you must subscribe to a distinctive ring
service from your local phone company. Do not turn on this function if
you do not subscribe to a distinctive ring service.
♦ Your fax may not be compatible with some distinctive ring services.
Distinctive ring is a service offered by some local telephone companies
whereby they assign an additional second number to your regular single line.
The second number rings differently from your normal number.
If you subscribe to a distinctive ring service, you can set the fax machine to
automatically answer when your second number is called. This allows you to
use the second number as an exclusive fax number.
To have your fax automatically answer when your second number is called,
follow the steps below:
Display:
FUNCTION
1 Press
once and
once.
OPTION SETTING
2 Press
3 Press
once and
3 times.
DISTINCTIVE
once.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Distinctive Ring (Requires Subscription to Service)
4 Press a number from 1 to 3 (1 to 5 in Canada) to select the ring pattern
below that matches your second number's ring pattern. Or, press 6 to
have your fax automatically answer your normal telephone number.
Press 7 to turn off the distinctive ring function.
RING PATTERN 1
RING PATTERN 2
RING PATTERN 3
Two short rings.
1
2
3
4
One short, one long, and one short ring.
Two short rings and one long ring.
Three very short rings.
RING PATTERN 4
(Canada only)
Two very short rings.
RING PATTERN 5
(Canada only)
5
STANDARD RING
OFF SETTING
Your standard (normal) ring pattern.
Turn distinctive ring off.
6
7
The display briefly shows
your selection, then:
FAX SIGNAL RX
STOP
5 Press
to return to the date and time display.
6 Set the reception mode to FAX.
RESOLUTION/
TEL FAX
RECEPTION MODE
♦ When using distinctive ring, you must set the reception mode of your fax to
FAX. When your designated fax number is dialed, your fax will
automatically answer and begin reception after two rings. Note that other
devices on the same line will also ring until your fax answers. If one of your
other numbers is dialed, the fax will ring; however, it will not answer.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Blocking Reception of Unwanted Faxes
Blocking Reception of Unwanted Faxes
The Anti Junk Fax function allows you to block reception of faxes from a party
that you specify. This saves paper by not printing out unwanted "junk" faxes.
To use this function, follow the steps below to enter the fax number from which
you do not wish to receive faxes. One fax number can be entered.
FUNCTION
Display:
ENTRY MODE
1 Press
2 Press
3 Press
once and
twice.
ANTI JUNK #
once and
twice.
once.
1=SET, 2=CLEAR
4 Press
to store an Anti Junk number, or
to clear a previously
1
2
stored number (if you are clearing a number, go to Step 6).
5 Enter the fax number by pressing the number keys (max. 20 digits).
STOP
START/MEMORY
6 Press
and then press
to return to the date and time
display.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Polling (Requesting a Fax Transmission)
Polling (Requesting a Fax Transmission)
Polling allows you to call another fax machine and have it send a document
(previously loaded in its feeder) to your machine without assistance from the
operator of the other machine.
♦ Hint: Polling is useful when you want the receiving fax machine, not the
transmitting fax machine, to bear the cost of the call.To use the polling
function, the other machine must be capable of being polled.
♦ To use the polling function, the other machine must be capable of being
polled.
♦ Before polling, make sure the other machine is set up to receive your
polling request.
♦ Your machine is not capable of being polled.
1 Dial the fax machine you want to poll
using one of the following methods:
• Enter the full number using the numeric keys.
SPEAKER
• Pick up the handset (or press
) and dial the full number. Wait for the
fax answerback tone.
• Press
the display.
or
until the name (or number) of the other party appears in
2 Press
.
POLL
• If you used the handset, replace it when POLLING appears in the display.
Reception will begin.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Printing Lists
You can print lists showing settings and information entered in the fax
machine. The lists are described below. To print a list, follow these steps.
Display:
FUNCTION
1 Press
once and
once.
LISTING MODE
TEL # LIST
2 Press
3 Press
once.
or
until the desired list appears in the display.
PRESS START KEY
4 Press
5 Press
once.
START/MEMORY
to print the list.
Telephone Number List
This list shows the fax and phone numbers that have been stored for
automatic dialing.
Setup List
This list shows your current selections for the FUNCTION key settings. The
list also shows your name and fax/telephone number as entered in the
machine, and a sample of the header printed at the top of every page you
transmit (HEADER PRINT).
Caller-ID List
This list shows information about your 30 most recent calls. (This list is only
available if you are using the Caller ID function.)
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report
This report is printed out automatically after an operation is completed to
allow you to check the result. Your fax machine is set at the factory to print out
the report only when an error occurs.
♦ The Transaction report cannot be printed on demand.
Headings in Transaction Report
SENDER/
RECEIVER
The name or fax number of the other machine involved in the
transaction. If that machine does not have an ID function, the
communication mode will appear (for example, "G3").
START
The time at which transmission/reception started.
Total time taken for transmission/reception.
Number of pages transmitted/received.
TX/RX TIME
PAGES
NOTE
(One of the following notes will appear under NOTE in the
report to indicate whether the transaction was successful,
and if not, the reason for the failure.)
OK - Transmission/reception was successful.
P.FAIL - A power failure prevented the transaction.
JAM - The printing paper or document jammed, preventing
the transaction.
BUSY - The fax was not sent because the line was busy.
COM.E-0 to COM.E-7 - A telephone line error prevented the
transaction. See Line error on page 64.
CANCEL - The transaction was cancelled because the
STOP key was pressed, no document was in the feeder, or
the other machine requested transmission using a function
which your fax machine does not have. If you were
attempting to fax, make sure a document is in the feeder. If
you were receiving, contact the faxing party to see how they
are trying to send to you.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Lists
Transaction Report print condition
You can change the condition under which a Transaction Report is printed out.
Follow the steps below.
Display:
FUNCTION
1 Press
2 Press
3 Press
once and
once.
OPTION SETTING
TRANSACTION
once and
once.
1:ALWAYS PRINT
once.
(Selections appear alternately)
4 Press a number from
to
to select the condition for printing.
1
5
1
ALWAYS PRINT
A report will be printed after each
transmission, reception, or error.
2
3
ERROR/MEMORY
SEND ONLY
A report will be printed after an error or a
memory operation.
A report will be printed after each
transmission.
4
5
ERROR ONLY
NEVER PRINT
A report will be printed only when an error
occurs.
A report will never be printed.
The display briefly shows
your selection, then:
DIAL MODE
STOP
5 Press
to return to the date and time display.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Maintenance
Print head
Clean the print head frequently to ensure optimum printing performance.
Note: Remove the paper from the paper tray before cleaning the print head.
1 Unplug the power cord, and open the
operation panel (press ➊).
2
1
2 Take the imaging film out of the print
compartment and place it on a sheet of
paper.
3 Wipe the print head with isopropyl
alcohol or denatured alcohol.
Caution!
• Do not use benzene or thinner. Avoid
touching the print head with hard
objects.
• The print head may be hot if your fax
machine has just received a large
number of documents. If this is the
case, allow the print head to cool prior
to cleaning.
Print head
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
4 Place the imaging film back in the print
compartment.
5 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
Scanning glass and rollers
Clean the scanning glass and rollers frequently to ensure the quality of
transmitted images and copies.
Note: Remove the paper from the paper tray before cleaning the scanning
glass and rollers.
1 Open the operation panel (press ➊).
2
1
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
2 Flip up the green levers on each side of
the white roller.
3 Wipe the scanning glass (under the
white roller) and rollers with a cotton
swab.
• Make sure that all dirt and stains (such
as correcting fluid) are removed. Dirt
and stains will cause vertical lines on
transmitted images and copies.
If the scanning glass is difficult to clean
If you find it difficult to remove dirt from the scanning glass, you can try moistening
the swab with isopropyl alcohol or denatured alcohol. Take care that no alcohol
gets on the rollers.
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
The housing
Wipe the external parts and surface of the machine with a dry cloth.
Caution!
Do not use benzene or thinner. These solvents may damage or discolor the
machine.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Troubleshooting
Problems and Solutions
If you have any problems with your fax, first refer to the following
troubleshooting guide. If you cannot solve the problem, call Sharp's Customer
Assistance Center at 1-800-BE SHARP.
Line error
Problem
Solution
LINE ERROR appears in
the display.
Try the transaction again. If the error persists, check
the following:
• Check the connection. The cord from the TEL.
LINE jack to the wall jack should be no longer than
six feet.
• Make sure there are no modem devices sharing the
same telephone line.
• Check with the other party to make sure their fax
machine is functioning properly.
• Have your telephone line checked for line noise.
• Try connecting the fax machine to a different
telephone line.
• If the problem still occurs, your fax machine may
need service.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Dialing and transmission problems
Problem
Solution
No dial tone when you
pick up the handset or
press the SPEAKER key.
• Make sure the handset cord is connected to the
correct jack. See Connecting the handset on page
9.
Dialing is not possible.
• Make sure the power cord is properly plugged into
a power outlet.
• Make sure that the telephone line is properly
connected to both the TEL. LINE jack and the wall
jack.
• Make sure that the fax machine is set to the correct
dialing mode for your telephone line. See Dial
mode on page 10.
The power is on, but no
transmission takes place.
• Make sure that the receiving machine has paper.
• If the receiving machine is in manual mode with no
attendant, reception will not be possible.
• Check the display for error messages.
• Pick up the handset and check for a dial tone.
Nothing is printed at the
receiving end.
• Make sure that the document for transmission is
placed face down in the feeder.
A distorted image is
received at the other end.
• Noise on the telephone line may cause distortion.
Try sending the document again.
• Make a copy of the document on your fax machine.
If the copy is also distorted, your fax machine may
need service.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Reception and copying problems
Problem
Solution
The fax machine doesn't
receive documents
automatically.
• Make sure that the reception mode is set to FAX. If
you subscribe to a distinctive ring service, make
sure that the Distinctive Ring function is set to the
correct ring pattern. If you do not subscribe to a
distinctive ring service, make sure that Distinctive
Ring is set to OFF SETTING. (See Distinctive Ring
on page 54.)
The printing paper comes • Make sure that the document is loaded properly in
out blank when you try to
receive a document.
the feeder of the transmitting machine. Make a
copy or print a report to confirm the printing ability
of your machine.
General print quality is
poor.
• It is important to select a paper that is appropriate
for the thermal transfer printer in your fax. We
recommend using laser quality paper that has a
very smooth finish. Copier paper will work, but it
sometimes tends to yield a lighter print quality.
The received document is • Ask the other party to send higher contrast
faint.
documents. If the contrast is still too low, your fax
machine may need service. Make a copy or print a
report to check your machine’s printing ability.
Received images are
distorted.
• Noise on the telephone line may cause distortion.
Have the other party try sending the document
again.
• The print head may be dirty. See Print head on
page 61.
• Make a copy or print a report on your fax machine.
If the copy or report is also distorted, your fax
machine may need service.
A received document or
copy prints out in strips.
• Make sure the operation panel is completely closed
(press down on both sides of the panel).
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
The quality of copies is
poor and/or dark vertical
lines appear.
• Any dirt or material on the scanning glass will
cause spots to appear on copies and transmitted
faxes. Clean the scanning glass as explained on
page 62.
Reception/copying is
interrupted.
• If reception or copying takes place continuously for
a long time, the print head may overheat. Turn off
the power and let it cool down. If overheating
frequently occurs, try changing the print contrast
setting to LIGHT (see page 15).
Dark vertical lines appear • Try changing the print contrast setting to LIGHT
on copies and received
faxes.
(see page 15).
General problems
Problem
Solution
Auto-dial numbers cannot • Make sure the fax is plugged in and the imaging
be stored in the fax.
film has been loaded. (Auto-dial numbers cannot
be stored if the imaging film has not been loaded.)
See Loading the Imaging Film on page 12.
Nothing appears in the
display.
• Make sure the power cord is properly plugged into
a power outlet.
• Connect another electrical appliance to the outlet to
see if it has power.
The machine does not
respond when you press
any of its keys.
• If a beep sound is not made when you press the
keys, unplug the power cord and then plug it in
again several seconds later.
Automatic document
feeding does not work for
transmission or copying.
• Check the size and weight of the document (see
Transmittable Documents on page 23).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Messages and Signals
Display messages
Note: If you have turned on the Caller ID function, see page 50 for display
messages related to Caller ID.
ADD PAPER & /
PRESS START KEY
(alternating messages)
Check the printing paper. If the tray is empty, add
paper and then press the START/MEMORY key. If
there is paper in the tray, make sure it is inserted
correctly (take out the stack, align the edges evenly,
and then reinsert it in the tray) and then press the
START/MEMORY key.
CHECK FILM/
CHECK COVER/
CHECK PAPER JAM
(alternating messages)
These alternating messages appear when there is a
problem in the print compartment that prevents
printing. Check to see if the imaging film is not loaded
properly or if it has been used up and needs
replacement. Make sure the operation panel is
completely closed (press down on both sides). If a
paper jam has occurred, clear the jam as explained in
the following section, Clearing Paper Jams.
CHECK PAPER SIZE
DOCUMENT JAMMED
The paper size setting is incorrect. Change the paper
size setting as explained on page 15.
The original document is jammed. See the following
section, Clearing Paper Jams. Document jams will
occur if you load more than 10 pages at once or load
documents that are too thick (see page 23).
FAX RX IN MEMORY
A fax has been received in memory because the
imaging film needs replacement, you have run out of
printing paper, or the paper is jammed. The fax will
print out automatically when the problem is fixed.
FUNCTION MODE
LINE ERROR
The FUNCTION key has been pressed.
Transmission or reception was not successful. Press
the STOP key to clear the message and then try
again. If the error persists, see Line Error on page 64.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
MEMORY IS FULL/
SEE MANUAL
(alternating messages)
The memory is full. This may occur during fax
reception if too much data is received before the
pages can be printed out. If faxes have been received
to memory because printing is not possible (an
additional message will indicate the problem), resolve
the problem so that printing can continue (see
Substitute Reception to Memory on page 46). If you
are attempting to transmit from memory, see If the
memory becomes full on page 39. If you are copying,
see If MEMORY IS FULL appears on page 47.
MEMORY PRINTING
NO DATA
The fax is preparing to or printing out a document
from memory.
This appears if you attempt to search for an auto-dial
number when none have been stored.
OFF HOOK
This appears if you forgot to replace the handset after
using it to dial and send a fax. Replace the handset or
press the STOP key to clear the message.
ON HOOK DIAL
OVER HEAT
The SPEAKER key has been pressed and the fax
machine is waiting for you to dial.
The print head has overheated. Operation can be
continued after it cools. If overheating frequently
occurs, try changing the print contrast setting to
LIGHT (see page 15).
PRINT HEAD FAIL/
The print head has failed and requires service.
YOU NEED SERVICE
(alternating messages)
READY TO SEND
RECALLING
A document has been loaded and the fax machine is
waiting for you to begin faxing or copying.
This appears if you attempt to send a fax by
automatic dialing and the line is busy or the receiving
fax machine does not answer. Your fax machine will
automatically reattempt the call. (See Automatic
redialing on page 36.)
TOTAL PAGE(S) 01
Number of pages transmitted, received, or copied.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Messages and Signals
Audible signals
Continuous tone
3 seconds
Indicates the end of transmission,
reception, or copying.
Intermittent tone
(3 beeps)
5 seconds
(1 second on, 1
second off)
Indicates incomplete transmission,
reception, or copying.
Rapid intermittent
tone
35 seconds
(0.7 seconds on,
0.3 seconds off)
Indicates that the handset is off hook.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
Clearing Paper Jams
Clearing a jammed document
If the original document doesn’t feed properly during transmission or copying,
or DOCUMENT JAMMED appears in the display, first try pressing
START/MEMORY . If the document doesn't feed out, remove it as explained below.
Important:
Do not try to remove a jammed document without releasing it as explained
below. This may damage the feeder mechanism.
1 Press ➊ and slowly open the operation
panel until it is half open.
2
1
2 Flip up the green levers on each side of
the white roller.
3 Gently and remove the document.
• Be careful not to tear the document.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Paper Jams
4 Flip down the green levers on each side of the white roller. Rotate the
front gear until the film is taut, and then close the operation panel (press
down on both sides to make sure it clicks into place).
Clearing jammed printing paper
1 Open the operation panel (press ➊).
2
1
2 Gently pull the jammed paper out of
the machine, making sure no torn
pieces of paper remain in the print
compartment or rollers.
3 Rotate the front gear until the film is taut, and then close the operation
panel (press down on both sides to make sure it clicks into place).
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Parts
Ordering Parts
To order parts, contact the parts distribution center located nearest
you. When ordering a part, use the part order number shown below.
Operation manual
Setup Guide
Handset cord
Telephone line cord
Hand set
TINSE4463XHTZ
TCADZ3744XHZZ
QCNWG209BXHOW
QCNWG370BXHZZ
DUNTK497CXHFW
CPLTP3183XHRF
CPLTP3222XHR2
Paper tray
Paper tray extension
Gears
CGERH2566XH01
NGERH2568XHZZ
Part distribution centers
Tritronics, Inc.
1306 Continental Drive
Abingdon, MD 21009
Tel: 1-800-638-3328
Fax: 1-800-888-FAXD
Tritronics, Inc.
Tel:1-800-365-8030
1015 NW 52nd Street
Ft. Lauderdale, FL 33309
Fax: 1-800-999-FAXD
Fox International, Ltd.
23600 Aurora Road
Tel: 1-800-321-6993
Fax: 1-800-445-7991
Bedford Heights, OH 44146
Andrews Electronics
25158 Avenue Stanford
Santa Clarita, CA 91355
Tel: 1-800-274-4666
Fax: 1-805-295-5126
Sharp Accessories and
Supply Center
Tel: 1-800-642-2122
2130 Townline Road
Peoria, IL 61615
73
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Regulatory Information
FCC Regulatory Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted
by the ACTA. On the rear of this equipment is a label that contains, among other
information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this
product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details. This equipment connects to the
telephone network through a standard USOC RJ-11C network interface jack.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not
ringing in response to an incoming call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the number of devices that may be
connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part of
the product identifier that has the format US:AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the
telephone company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, or for repair or warranty information,
please contact Sharp’s Customer Assistance Center. The number is 1-877-794-8675. If
the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
This equipment may not be used on coin service provided by the telephone company.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this equipment ID does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
This equipment is hearing-aid compatible.
When programming and/or making test calls to emergency numbers:
♦ Remain on the line and briefly explain to the dispatcher the reason for the call.
♦ Perform such activities in the off-peak hours, such as early morning or late evening.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Date Revised:
.
Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (1/2)
MSDS No. B-1026
Section 1. Product and Company Identification
Product Name : IMAGING FILM UX-5CR
Supplier Identification : Sharp Corporation
22-22 Nagaike-cho, Abeno-ku, Osaka, Japan
DAINIPPON PRINTING CO. LTD.
591-2, Kamihirose, Higashikubo, Sayamashi, Saitama, 350-1321 JAPAN
Manufacturer :
Emergency telephone number : +81-42-952-9666
Local suppliers are listed below. Please contact the nearest supplier for additional information.
(Country)
U.S.A.
(Name and Telephone Number)
Sharp Electronics Corporation
Telephone number for information: 1-800-237-4277
Canada
Sharp Electronics of Canada Ltd.
Telephone number for information : 905-890-2100
Emergency telephone number :
1-800-255-3924
Section 2. Ingredients
Ingredients
CAS No.
Proportion
OSHA PEL ACGIH TLV
Other
Polyethylene terephthalate film 25038-59-9
47 ~ 52%
-
-
None
Coating layer substances
Carbon Black
Ester wax
Parraffin Wax
Microcrystalline wax
Ethylene Vinyl Acetate Copolymer 24937-78-8
Others
3
3
3
1333-86-4
8015-86-9
8002-74-2
63231-60-7
7 ~ 10%
2 ~ 7%
10 ~ 14%
16 ~ 22%
1 ~ 5%
3.5 mg/m
3.5mg/m
None
None
None
None
None
None
-
-
-
-
-
-
2.0mg/m
-
-
-
1 ~ 6%
Section 3. Hazardous Identification
Route(s) of Entry:
Inhalation?
NO
Skin?
NO
Ingestion?
Possible but very unusual
Signs and Symptoms of Exposure: None
Medical Conditions Aggravated by Exposure: None
POTENTIAL HEALTH EFFECTS:
Inhalation:
None
None
None
None
Skin Contact:
Eye Contact:
Ingestion:
Section 4. First-Aid Measures
Inhalation: No applicable
Skin Contact: In case of contact, usually special care in not necessary. If it dirties skin, clear with water and soap.
Eye Contact: In case of contact, immediately flush eyes with plenty of water. If necessary, then care for medical attention.
Ingestion: Immediately make vomit it and rinse mouth with water. If necessary, then care for medical attention.
Section 5. Fire-Fighting Measures
°
Flash Point: about 250 C for ink
Autoignition: None
Flammability Limits: Not applicable
Extinguishing Media: CO2, Water, Dry chemicals, Foam
Firefighting: None
Fire and Explosion Hazard: None
Hazardous Combustion Products: None
75
Download from Www.Somanuals.com. All Manuals Search And Download.
S H A R P
Date Revised:
.
Date Issued :July. 3. 2001
MATERIAL SAFETY DATA SHEET (2/2)
MSDS No. B-1026
Section 6. Accidental Release Measures
Rumpling the product may cause the wax layer to peel off. Sweep up or vacuum. When sweeping, avoid
raising film or dust. If a vacuum is used , motor should be rated as dust tight. Wash any residue off skin with
soap and water. Garments may be wasted or dry cleaned after removal of loose film or dust.
Section 7. Handling and Storage
No special precautions for safety reason.
Store in cool, dry place ,avoid direct sunlight.
Section 8. Exposure Control/Personal Protection
Ventilation: None
Eye Protection: None
Protective Clothing: None
Gloves: None
Section 9. Physical and Chemical Properties
Description: Not applicable
°
Melting Point: 71 C
Pressurized: None
pH: None
Evaporation Rate: Negligible
Volatility: None
Freezing Point: None
Boiling Point: None
Specific Gravity (H20 = 1): about 1.2
Water Solubility: Not applicable
Section 10. Stability and Reactivity
Stability:
Stable
Conditions to Avoid:
Incompatibility(Materials to Avoid):
None
None
Hazardous Decomposition or Byproducts: CO, CO2, NOX and H2O
Hazardous Polymerization:
Will not occur
Section 11. Toxicological Information
Acute Toxicity: None
Chronic Toxicity: None
Section 12. Ecological Information
No environmental effect at normal use.
Section 13. Disposal Consideration
Dispose by the same method of ordinary plastic products in accordance with all applicable regulations. Any
disposal practice must be in compliance with local, state and federal laws and regulations. If necessary,
contact government office and ensure conformity with disposal regulations.
Section 14. Transport Information
No specific precautionary transport measure for safety reasons.
As to storage conditions, see section 7.
Section 15. Regulatory Information
None
Section 16. Other Information
The information herein is given in good faith, but no warranty, if used any process.
Final determination of suitability of any material is the sole responsibility of the user.
Although certain information are described herein, we cannot guarantee, that these are the only hazard, which exist.
Information on this data sheet represents our current data and best opinion as to the proper use in handling of
this product under normal conditions.
Restrictions: This information relates only to the specific material designated as supplied by the manufacturer. This
information is supplied to us by the manufacturer and Sharp offers no warranties as to its accuracy and
accepts no responsibilities for any typographical errors which may appear on these sheets. It is the
responsibility of the user to determine the suitability of this product for each particular use.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Reference Guide
Sending Faxes
Receiving Faxes
RESOLUTION/
RECEPTION MODE
Place your document (up to 10 pages) face
down in the document feeder.
Press
until the arrow in the
display points to the desired reception
mode.
TEL FAX
RESOLUTION/
JAN-01 10:30
RECEPTION MODE
TEL FAX
JAN-01 10:30
FAX mode: The fax machine automatically
answers and receives the incoming
document.
Normal Dialling
SPEAKER
TEL mode: Answer all calls (even faxes)
by picking up the handset. To begin fax
1.Lift the handset or press
2.Dial the fax number.
.
START/MEMORY
reception, press
.
3.Wait for the reception tone (if a person
answers, ask them to press their Start
key).
Storing Auto Dial Numbers
START/MEMORY
4.Press
.
FUNCTION
1.Press
once and
once.
Speed Dialling
2.Enter a 2-digit Speed Dial number (01 to
30).
SPEED
1.Press
.
START/MEMORY
3.Enter the fax number and press
.
2.Enter the 2-digit Speed Dial number.
4.Enter a name by pressing number keys.
(To enter two letters in succession that
START/MEMORY
3.Press
require the same key, press
entering the first letter.)
after
Search Dialling
G =
N =
U =
V =
SPACE =
A =
1.Press
or
until the name of the
H =
O =
P =
Q =
R =
S =
T =
other party appears in the display (if no
name was stored, the number will
appear).
B =
C =
D =
W =
X =
Y =
Z =
I
=
J =
K =
L =
E =
F =
START/MEMORY
M =
2.Press
.
STOP
START/MEMORY
5.Press
and then
.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Guía de referencia rápida
Transmisión de documentos
Recepción de documentos
RESOLUTION/
Coloque el documento (hasta 10 páginas)
mirando hacia abajo en el alimentador.
RECEPTION MODE
Pulse
hasta que la flecha del
display señale el modo de recepción deseado.
TEL FAX
RESOLUTION/
JAN-01 10:30
RECEPTION MODE
TEL FAX
JAN-01 10:30
Modo FAX: El aparato de telefax
contestará y recibirá documentos
automáticamente.
Marcación normal
Modo TEL: Contesta todas las llamadas
(incluso las de telefax) levantando el auricular.
Para que comience la recepción del
SPEAKER
1.Levante el auricular o pulse
.
2.Marque el número de telefax.
START/MEMORY
documento, pulse
.
3.Espere a escuchar el tono de recepción
(si alguien contesta el teléfono, pídale
que pulse su tecla Inicio).
Programación de números de
marcación automática
START/MEMORY
4.Pulse
.
FUNCTION
1. Pulse
una vez y
una vez.
Marcación abreviada
2. Introduzca un número de 2 dígitos de
Marcación abreviada (01 a 30).
SPEED
1.Pulse
.
3. Introduzca el
2.Introduzca el número de 2 dígitos de
marcación abreviada.
START/MEMORY
número de telefax y pulse
.
START/MEMORY
3.Pulse
.
4. Introduzca un nombre pulsando las
teclas numéricas. (Para introducir dos
letras sucesivas que requieran la
Marcación por búsqueda
misma tecla, pulse
después de
1.Oprima la tecla de flecha
o
hasta
introducir la primera letra).
que en el visor aparazca el destino deseado
.
G =
N =
U =
V =
SPACE =
A =
H =
O =
P =
Q =
R =
S =
T =
START/MEMORY
B =
C =
D =
W =
X =
Y =
Z =
I
=
2. Pulse
.
J =
K =
L =
E =
F =
M =
START/MEMORY
5. Pulse
y, a continuación,
STOP
.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
A
H
Anti Junk Fax, 56
Audible signals, 70
Auto-dial numbers
Storing, 29
Halftone setting, 25
Handset, 9
Handset receiver volume, 22
Hold, 43
Using, 33, 34
Housing, cleaning, 63
C
I
Caller ID, 49-53
Caller ID List, 58
Contrast, 26
Imaging film, replacing, 12
J
Copies, 47
Copy cut-off setting, 48
Jams, clearing, 71-72
L
D
Letters, entering, 17, 30
Line error, 64
Date, setting, 18
Daylight Saving Time, 19
Dial mode, 10
Dialing
Loading paper, 14
Loading the document, 24
Direct Keypad, 35
Normal, 27
Search, 34
M
Memory transmission, 38
Memory, substitute reception to, 46
Speed, 33
Direct Keypad Dialing, 35
Display messages, 68
Distinctive ring, 54
Document feeder, 24
Document guides, 24
Document restrictions, 24
Document sizes, 23
Document, maximum scanning size, 23
N
Normal Dialing, 27
Number of rings in FAX reception mode,
40
O
Ordering parts, 73
E
P
Extension telephone
Using, 43
Paper jams, clearing, 71-72
Paper size setting, 15
Paper, loading, 14
Polling, 57
Power cord, 9
Print contrast setting, 15
F
FAX reception mode, 20, 40
Fax Signal Receive, 44
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Print head, cleaning, 61-62
Priority Call, 52
Sender’s name and number, entering,
16-17
Setup List, 58
Speaker volume, 21
Speed Dialing, 33
R
Reception mode
FAX mode, 20, 40
TEL mode, 20, 41
Reception Ratio setting, 45
Redialing, 36
T
TEL reception mode, 20, 41
TEL. LINE. jack, 10
Resolution, 25
Ringer volume, 22
Telephone line cord, 10
Telephone Number List, 58
Time, setting, 18
Transaction Report, 59
Setting print condition, 60
S
Scanning glass, cleaning, 62
Search Dialing, 34
80
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this Sharp
brand product (the "Product"), when shipped in its original container, will be free from defective
workmanship and materials, and agrees that it will, at its option, either repair the defect or replace
the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded
item(s) set forth below nor to any product the exterior of which has been damaged or defaced,
which has been subjected to misuse, abnormal service or handling, or which has been altered or
modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set
forth below and provided proof of purchase to the servicer.
To the extent permitted by applicable state law, the warranties set forth herein are in lieu of, and
exclusive of, all other warranties, express or implied. Specifically,ALL OTHER WARRANTIES
OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED. ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE,
AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under
applicable state law, implied warranties may not validly be disclaimed or excluded, the duration of
such implied warranties is limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties
other than those described above, or to extend the duration of any warranties beyond the time
period described above on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and
shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the
manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall
constitute full satisfaction of all claims, whether based on contact, negligence, strict liability or
otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects
in the Product which were caused by repairs or attempted repairs performed by anyone other than
an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or
consequential economic or property damage. Some states do not allow limits on warranties or on
remedies for breach in certain transactions; in such state the limits herein may not apply.
Your Product:
Personal Facsimile
Warranty Period for this Product:
Additional items excluded
from warranty coverage:
Where to obtain service:
Ninety (90) days parts and labor from date of purchase.
Any consumable items such as paper supplied with the
Product.
At a Sharp Authorized Servicer located in the United States.
To find out the location of the nearest Sharp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
What to do to obtain service:
Ship (prepaid) or carry in your Product to a Sharp Authorized Servicer.
Be sure to have proof of purchase available. If you ship or mail the
Product, be sure it is packaged carefully.
World Wide Web or call 1-800-BE SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza,
Mahwah, New Jersey 07430-1163
Download from Www.Somanuals.com. All Manuals Search And Download.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-1163
SHARP CORPORATION
PRINTED IN THAILAND
(TINSE4463XHTZ)
Download from Www.Somanuals.com. All Manuals Search And Download.
|