ENGLISH
CP-SW1000H
ENGLISH
Introduction
Thank you for purchasing this SHARP product. To obtain the best
performance from this product, please read this manual carefully. It
will guide you in operating your SHARP product.
Features
Cleaning cloth x 1
Subwoofer stand x 2
This subwoofer incorporates the Tymphany
Linear
Array
Transducer ( LAT ) technology developed by Tymphany Corporation.
This Technology uses a linear array of multiple smaller diaphragms
to generate sound as opposed to the single diaphragm used in the
conventional cone speakers. Such arrangement enables:
ꢀPowerful low bass without the need for large enclosures
compared to the conventional speakers, hence the sleek and
compact design of this subwoofer.
Spike x 4
Foot cushion x 4
ꢀMinimization of structural vibrations which makes it possible to
place the subwoofer close to your audio system without affecting
the critical circuitry.
Contents
Page
ꢁ General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessories
Please confirm that the following accessories are included.
ꢁ Preparation for Use
Subwoofer preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Placing the subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Subwoofer connections to TVs . . . . . . . . . . . . . . . . . . . . . . . . . . 5
AC power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 7
Remote control x 1
AC power lead x 1
ꢁ Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 8
ꢁ Advanced Feature
Operating the TV with the remote control . . . . . . . . . . . . . . . . . 8
ꢁ References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RCA cable (2 pins - 2 pins) x 1
RCA cable (1 pin - 2 pins) x 1
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and indicators
CP-SW1000H
ENGLISH
ꢁ Front panel
Reference page
1. Bass Reflex Duct. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Remote Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Volume Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Crossover Frequency Control . . . . . . . . . . . . . . . . . . . . . . . . 8
5. ON/STAND-BY Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6. STAND-BY Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1
2
3
6
4
5
ꢁ Rear panel
Reference page
1. AC Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Audio Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ꢁ Remote control
Reference page
1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. TV Operation Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Volume Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . . 8
1 2 3
1
2
TV Operation Buttons (Only SHARP TV):
On/Stand-by
Button
Sets the TV
power to
“ON” or
Input Select
Button (TV)
Press the
button to
switch the
input source.
4
“STAND-BY”.
Plastic shield
Remote
control
Volume Up and Turn up/ Channel Up and Switch up/
Down Buttons down the TV Down Buttons down the TV
volume.
channels.
3
Battery holder
Note:
Some models of SHARP TV may not be operable.
Note:
Before using remote control, please remove plastic shield at battery
holder.
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Subwoofer preparation
Placing the subwoofer
Installation image:
CP-SW1000H
ENGLISH
Make sure to unplug the AC power lead before installing the main
unit or changing the position.
Select from three installation methods according to the preferred
position.
TV
Horizontal position
Using spikes
VCR
DVD player
1 Tighten all spikes as shown
Notes:
ꢀWhen attaching the spikes, place the subwoofer on a cushion or
soft cloth to avoid damage.
ꢀThe subwoofer can be leveled by adjusting the spikes.
Caution:
Place the subwoofer as shown.
Notes:
ꢀAs the bass sound from the subwoofer is omni-directional, you
can place the subwoofer anywhere you like. However, it is
recommended to place it as close to the TV as possible.
ꢀThe front panel of the subwoofer is not removable.
When using these spikes on glossy or slippery table such as on glass
top, this subwoofer may slip and fall off the table.
Caution:
ꢀDo not change the installation direction when the subwoofer is
turned on.
Using foot cushions
ꢀDo not allow any objects to fall into or to be placed in the bass
reflex ducts.
ꢀDo not stand or sit on the subwoofer as you may be injured.
1 Attach the foot cushions as shown
Note:
When attaching the foot cushions, place the subwoofer on a cushion
or soft cloth to avoid damage.
ꢁ Magnetically shielded speakers
The subwoofer can be placed near a TV set as the built-in speakers
are magnetically shielded. However, uneven colours may appear on
the screen depending on the type of TV.
Vertical position
1 Place subwoofer stand as shown
If colour variation occurs.
Turn off the TV (from the power switch).
After 15 - 30 minutes, turn the TV on again.
If the colour variation is still present.
Move the subwoofer further away from the TV.
Do not place the unit near any kind of magnet or an electromagnet
as irregular colours may appear on the TV screen.
Stand
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Subwoofer connections to TVs
CP-SW1000H
ENGLISH
Caution:
Turn off all other equipment before making any connections.
ꢁ Connecting to a TV (with subwoofer pre-out)
If the TV/monitor has subwoofer pre-out, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
Notes:
ꢀRefer to the operation manual of the equipment to be connected.
ꢀFully insert the plugs to avoid fuzzy pictures or noises.
Caution:
TV
Tuner receiving for other audio system
ꢀPlacing the aerial near the subwoofer unit AC power lead may
cause noise pick up. Place the aerial away from the subwoofer
unit for better reception.
To SUBWOOFER PRE-OUT
socket
Audio cable (supplied)
ꢁ Connecting to a TV
If the TV/monitor has an audio output, connect it to the AUDIO
INPUT sockets on the rear of the subwoofer.
To AUDIO
INPUT sockets
TV
Subwoofer
To audio output sockets
Audio cable (supplied)
To AUDIO
INPUT sockets
Subwoofer
E-5
Download from Www.Somanuals.com. All Manuals Search And Download.
AC power connection
Remote control
CP-SW1000H
ENGLISH
After checking all the connections have been made correctly,
connect the AC power lead to the AC power input socket, then to the
wall socket.
ꢁ Battery installation
1
Whilst pushing the locking tab towards the centre of the
remote control, slide out the battery holder.
Back of remote control
Locking tab
2
Remove the old battery from the battery holder, insert the
new battery and then slide the battery holder back into the
remote control.
Wall socket
(AC 220 - 240 V ~ 50 Hz (Europe))
(AC 220 - 240 V ~ 50/60 Hz (others))
Battery holder
Positive (+) side up
Notes:
ꢀNever use a power lead other than the one supplied. Otherwise,
a malfunction or an accident may occur.
Polarity (+) symbol
Battery type
ꢀUnplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.
Locking tab
Precautions for battery use:
ꢀRemove the battery if the unit will not be used for long periods of
time. This will prevent potential damage due to battery leakage.
Caution:
ꢀDo not use rechargeable battery (nickel-cadmium battery, etc.).
ꢀReplace only with the same or equivalent type.
ꢀInstalling the battery incorrectly may cause the unit to malfunction.
ꢀDanger of explosion if battery is incorrectly replaced.
ꢀBatteries (battery pack or batteries installed) shall not be exposed
to excessive heat such as sunshine, fire or the like.
E-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control (continued)
General control
CP-SW1000H
ENGLISH
Notes concerning use:
ꢀReplace the battery if the operating distance is reduced or if the
operation becomes erratic. Purchase “CR 2025”, coin lithium
battery.
ꢀPeriodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.
ꢀExposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
ꢀKeep the remote control away from moisture, heat, shock, and
vibrations.
ꢁ Test of the remote control
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown below:
Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy your system.
ꢁ To turn the power on
Press the ON/STAND-BY button.
The volume indicator lights up
blue.
Position A
Position B
Remote sensor
(Lights
up blue)
If the power does not turn on,
check whether the power lead is
plugged in properly.
Remote sensor
To set the unit to stand-by mode:
Press the ON/STAND-BY button
again.
The STAND-BY indicator lights up
red.
0.2 m - 6 m
(8” - 20’)
(Turns red)
15˚
15˚
0.2 m - 6 m
(8” - 20’)
15˚15˚
E-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the TV with the remote
control
CP-SW1000H
ENGLISH
ꢁ Volume control
Main unit operation:
Turn volume knob clockwise to increase the volume and anti-
clockwise to decrease the volume.
You can operate SHARP TV with this system’s remote control.
Remote control operation:
Press the VOL + button to increase the volume and the VOL – button
to decrease the volume.
Note:
Do not turn the volume knob manually in reverse direction when
operating it by remote control.
TV operation buttons
ꢁ Crossover frequency control
Adjust the high frequency cut-off point. Frequencies higher than the
set frequency are removed.
To emphasise the bass, turn this control towards 80 Hz and increase
the volume.
ꢁ Watching TV
Notes:
Observe the following to avoid malfunction and sound distortion.
ꢀDo not set the volume too high on the audio system. The
subwoofer may be damaged.
ꢀBefore you switch on/off the subwoofer, minimise the volume on
the audio system.
Point the remote control at the TV.
1 Press the TV POWER button to turn on the TV.
2 Press the CH UP
channel.
or CH DOWN
button to set the
ꢁ Auto power off
If no signal is detected for 20 minutes during power on, the
subwoofer will automatically go to stand-by mode.
Pressing the CH UP
channel switching.
or CH DOWN
button enables TV
3 Press TV VOL + or – button to adjust the TV volume.
Other operable button
Press the Input Select button to switch the input source. (TV)
Note:
Some models of SHARP TV may not be operable. In this case, use
the remote control supplied with each product.
E-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting chart
CP-SW1000H
ENGLISH
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
ꢁ Condensation
Sudden temperature changes, storage or operation in an extremely
humid environment may cause condensation inside the cabinet.
Condensation can cause the unit to malfunction. If this happens,
leave the power on until normal playback is possible (about 1 hour).
Wipe off any condensation on the transmitter with a soft cloth before
operating the unit.
ꢁ General
Symptom
Possible cause
No sound is heard. ꢀIs the input signal (selection) set
properly?
ꢁ If problem occurs
ꢀIs the volume level set to “0”?
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.
Noise is heard during ꢀMove the subwoofer away from any
playback.
computers or mobile phones.
When a button is ꢀSet this unit to the stand-by mode and
pressed, the unit
does not respond.
then turn it back on.
If such a problem occurs, do the following:
1. Set the unit to the stand-by mode and turn the power on again.
2. If the unit is not restored in the previous operation, unplug and
plug in the subwoofer, and then turn the power on.
The power is not
turned on.
ꢀIs the unit unplugged? (Refer to page 6)
ꢀThe protection circuit may be activated.
Unplug and plug in the power lead again
after 5 minutes or more.
ꢁ Remote control
Symptom
Possible cause
The remote control ꢀIs the battery polarity correct?
does not operate
properly.
ꢀIs the battery dead?
ꢀIs the distance or angle incorrect?
ꢀAre there any obstructions in front of the
subwoofer?
ꢀIs there a strong light shining on the
remote sensor?
ꢀIs the remote control for another
equipment used simultaneously?
Thesubwoofercannot ꢀIs the AC power lead of the subwoofer
be turned on with the
remote control.
plugged in?
ꢀIs the battery inserted?
TV cannot be
operated with the
remote control.
ꢀDepending on the model, some or all
functions may not be operable using the
remote control of this unit. In this case,
use the remote control supplied with the
TV.
E-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Specifications
CP-SW1000H
ENGLISH
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
ꢁ Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth.
Caution:
ꢀDo not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet finish.
ꢀDo not apply oil to the inside of each component. It may cause
malfunctions.
ꢁ General
Power source
AC 220 - 240 V ~ 50 Hz (Europe)
AC 220 - 240 V ~ 50/60 Hz (others)
Power consumption
Power on: 18 W
Power stand-by: 0.6 W(*)
Amplification system Subwoofer: Pulse width modulation
Output power
Audio input terminal
Type
RMS: 100 W (50 W + 50 W) (DIN 45 324)
Analog input: RCA type x 1 pair (L/R)
Subwoofer system
Impedance
4 ohms x 2
Dimensions
Width: 430 mm (16-15/16")
Height: 151 mm (5-15/16")
Depth: 323.5 mm (12-3/4")
Weight
6.4 kg (14.11 lbs.)
Crossover frequency 80 Hz - 220 Hz
( * )This power consumption value is obtained when in the power
stand-by mode.
E-10
Download from Www.Somanuals.com. All Manuals Search And Download.
|