OWNER’S GUIDE
NH15
NH15C
NH15W
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
For Household Use Only
HOSE ATTACHMENTS:
DUST CUP/FILTERS/ACCESSORIES:
1. DO NOT use if air flow is restricted;
if the air paths, the hose, or the
accessories become blocked, turn
the vacuum cleaner off. Remove all
obstructions before you turn on the
unit again.
1. Before turning on the vacuum:
• Make sure that all filters
are thoroughly dry after routine
cleaning.
WHEN USING AN ELECTRICAL
APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD
WARNING –TO REDUCE THE
RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
• Make sure that dust cup and all
filters are in place after routine
maintenance.
2. Keep the end of the hose and
accessory openings away from face
and body.
• Make sure accessories are free
of blockages.
ALWAYS BE OBSERVED,
GENERAL ELECTRICAL SAFETY:
3. Keep cleaning tools and hose
suction openings away from hair,
face, fingers, uncovered feet, or
loose clothing.
INCLUDING THE FOLLOWING:
1. Unplug from electrical outlet when
not in use and before servicing.
• Only use filters and accessories
provided by EURO-PRO
Operating LLC. [Failure to do so
will void the warranty.]
READ ALL INSTRUCTIONS
BEFORE USING YOUR SHARK
MULTI-VAC VACUUMING
SYSTEM.
2. DO NOT use vacuum with a
damaged cord or plug. If appliance
is not working as it should, has
been dropped, damaged, left
outdoors, or dropped into water,
return it to EURO-PRO Operating
LLC for examination, repair, or
adjustment.
4. Only use manufacturer’s
recommended attachments.
GENERAL CLEANING:
GENERAL USE:
1. DO NOT run the vacuum over
POLARIZED PLUG:
large-sized objects.
1. Use only as described in this
manual.
To reduce the risk of electric
shock, this appliance has a
polarized plug (one blade is
wider than the other). As a
safety feature, this plug will
fit into a polarized outlet only
one way. If the plug does not
fit fully into the outlet, reverse
the plug. If it still does not fit,
contact a qualified electrician.
DO NOT force into outlet or try
to modify to fit.
2. DO NOT pick up hard or sharp
objects such as glass, nails, screws
or coins that could damage the
vacuum cleaner.
3. DO NOT pull or carry vacuum by
2. DO NOT put any objects into
openings. DO NOT use with any
opening blocked; keep free of dust,
lint, hair, and anything that may
reduce air flow.
the cord.
4. DO NOT unplug by pulling on cord;
to unplug, grasp the plug, not the
cord.
3. DO NOT pick up smoking or
burning objects such as hot coals,
cigarette butts, or matches.
5. DO NOT pull vacuum by the cord.
3. Keep your work area well lit.
4. DO NOT pick up flammable or
combustible materials such as
lighter fluid, gasoline, or kerosene
or use vacuum in areas where they
may be present.
6. DO NOT handle plug or appliance
4. Keep the vacuum moving over the
carpet surface at all times to avoid
damaging the carpet fibers.
with wet hands.
7. DO NOT run the vacuum over the
power cord.
5. DO NOT place vacuum on unstable
surfaces such as chairs or tables.
8. DO NOT use the cord as a handle.
5. DO NOT pick up toxic solutions
such as chlorine bleach, ammonia,
or drain cleaner.
6. DO NOT allow young children to
operate the vacuum or use as a toy.
Close attention is necessary when
used by or near children.
9. DO NOT close a door on the cord.
10. DO NOT pull cord around sharp
corners. The use of an extension
cord is not recommended.
6. DO NOT use in an enclosed space
where vapors are present from
paint, paint thinner, moth-proofing
substances, flammable dust or
other explosive or toxic materials.
7. DO NOT use vacuum cleaner if it
has been dropped, damaged, left
outdoors, or submerged in water.
Return to EURO-PRO Operating
LLC for examination, repair, or
adjustment.
11. DO NOT leave appliance when
plugged in.
12. Keep cord away from heated
surfaces.
7. DO NOT vacuum up any liquids.
8. DO NOT immerse vacuum cleaner
13. Turn off all controls before
plugging or unplugging vacuum
cleaner.
in water or other liquids.
8. DO NOT use without dust cup and/
or filters in place.
9. DO NOT use outdoors or on wet
WARNING: To reduce the risk of
electric shock or injury, do not
use outdoors or on wet surfaces.
surfaces; use only on dry surfaces.
14. Store your appliance with the
power cord secured around the
two cord holders—as shown in the
Storage instructions
10. Use extra care when cleaning
on stairs.
TOLL FREE: 1-800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
NO MORE BENDING!
Use the Shark Backsaver™
wand on portable canister
mode to reach low while
you stand upright.
Three different modes –all with
constant suction power. Your Multi-Vac
converts, pivots, and bends to meet all
your cleaning needs
2
3
1
1
HAND VAC
2
PORTABLE CANISTER
3
STICK VAC
Use the Hand Vac as a standalone
vacuum or with flexible hose and
cleaning tools:
Connect the Hand Vac to the
Flexible Hose and Backsaver™
Wand to extend your reach:
Attach the Hand Vac to the Shark
Backsaver™ Wand for even more
cleaning flexibility:
Hand Vac for spot-cleaning floor
spills and large piles of debris
BACKSAVER™ Wand bends under
furniture and other hard-to-reach
floor spaces while you stand
upright.
Upright vacuuming – floors and
carpets
With Flexible Hose and Pet Hair
Power Brush for above-the-floor
cleaning
Swivel Floor Nozzle pivots for
effortless steering. The unique
widebrow nozzle picks up large
piles of debris.
NOTE: Always turn power off
before attaching or detaching
Hand Vac and accessories.
With 2-in-1 Crevice/Dusting Tool
for hard-to-reach places such as
corners and under radiators
TOLL FREE: 1-800-798-7398
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Contents
Getting Started......................................................................2
Mode 1: Hand Vac.................................................................3
Mode 2: Portable Canister ................................................6
Mode 3: Stick Vac ................................................................10
Storage......................................................................................14
Maintenance............................................................................15
Troubleshooting Guide .......................................................18
Checking for Blockages......................................................20
Warranty and Registration................................................21
Thank you for
purchasing
the Shark®
Multi-Vac.
TOLL FREE: 1-800-798-7398
1
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Getting Started
Mode 1: Hand Vac with Connections
CAUTION: The Power Button for
all three modes is on the Hand Vac
handle. Always turn the power OFF
before plugging and unplugging,
h
g
when adding or removing
2
attachments, or when connecting
Hand Vac to or from the
Backsaver™ Wand.
c
b
i
d
1
a
e
j
3
f
STANDALONE HAND VAC
You can use the standalone Hand
Vac for spot-cleaning, and large
particle pick-up.
3 While holding Hand Vac, press
Power Button to begin cleaning.
Hold Hand Vac to turn off the
Power Button.
a Hand Vacuum
g 2-in-1 Crevice/Dusting Tool
b Flexible Stretch Hose
c Backsaver™ Handle
d Hose Mount
h Pet Hair Power Brush
i
j
Air Dam (Hand Vac Mode)
1 Slide pointed ends of Air Dam
(U-shaped bracket) into tracks on
either side of the inlet opening on the
bottom of the Dust Cup. Press firmly
to ensure that Air Dam is in place.
5 Empty Dust Cup after cleaning and
periodically during cleaning when
it appears full. (See “Maintenance”
section for instructions.)
Filters
e Backsaver™ Wand
TECHNICAL SPECIFICATIONS
Voltage: 120V., 60Hz.
Power: 800 Watts
f
Shark™ Widebrow Floor Nozzle
with Swivel Steering
2 When ready to vacuum, make sure
all three wheels are resting on the
ground. This allows the Air Dam to
guide debris to inlet opening.
2
TOLL FREE: 1-800-798-7398
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Mode 1: Hand Vac Accessories
1
To remove and store Air Dam:
grip the center of the Air Dam
and slide out of tracks. Store
Air Dam in the slot on the
Hand Vac exhaust filter cover.
3
2
HAND VAC WITH HOSE
AND ACCESSORIES
For cleaning and dusting above-
the-ground and for hard-to-reach
places:.
Attach cleaning tool to the other
end of the Hose:
SUPER FLEXIBLE HOSE: With the
PET HAIR POWER BRUSH : This
right cleaning tool in place and this
flexible hose, you can extend your
reach into hard-to-clean areas.
unique tool was engineered for fast
and easy removal of pet hair and
ground-in dirt from carpeted stairs
and upholstery.
• Pet Hair Power Brush or
• 2-in-1 Crevice/Dusting Tool
4 While holding Hand Vac, turn on
1
Slide Air Dam from underside of
Dust Cup and store in the slot on the
exhaust filter cover.
2-IN-1 CREVICE/DUSTING TOOL:
This tool allows you to reach into
narrow cleaning spaces, between
cushions, under radiators and
NOTE: Use hose without tools for
large debris cleaning.
Power Button to begin cleaning.
5 Hold Hand Vac to turn off Power
Button
2
Slide Hose Mounting Plate into
grooves on the underside of the Dust
Cup so that Hose Mount assembly
covers the inlet on Hand Vac.
baseboards, or hard-to-reach
6 Empty Dust Cup after cleaning and
periodically during cleaning when
it appears full. (See “Maintenance”
section for instructions.)
corners; it also allows you to dust a
variety of surfaces from furniture
and window blinds to lamp shades
and book shelves. In addition, the
nylon bristles make the tool safe to
use on most fabric surfaces.
3 Click the shorter end of the Flexible
Hose into Hose Mount.
4
TOLL FREE: 1-800-798-7398
5
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Mode 2: Portable Canister
1
Use portable canister mode
for low reach cleaning under
furniture.
a
b
d
e
f
3
c
g
i
h
j
2
4
k
You can combine the Hand Vac with
the Flexible Hose and the Backsaver™
Wand to create a versatile
cleaning tool.
g
Cord Guide ( for stick Mode)
PORTABLE CANISTER
BACKSAVER™ MODE:
FOR LOW-REACH CLEANING:
3 Remove Air Dam from Hand Vac and
place the Air Dam in the slot on the
Hand Vac exhaust filter cover.
h Locking Dial
i
j
Hand Vac Mount Pins
1
To assemble the Backsaver™ Wand
for the first time, grip the Backsaver™
Handle and slide the wand into the
channel above the hinged elbow—so
that the Backsaver™ Handle Release
button faces in the same direction
as the Floor Nozzle. Snap the wand
into place.
4 Slide Hose Mounting Plate onto
Bottom Cord Wrap Holder
GETTING TO KNOW THE
BACKSAVER™ WAND ASSEMBLY:
a Backsaver™ Handle Release Button
Hand Vac so that inlets are aligned.
k Floor Nozzle
b Backsaver™ Handle
c Hinged Elbow
CAUTION: The Power Button for
all three modes is on the Hand Vac
handle. Always turn the power OFF
before plugging and unplugging,
when adding or removing
d Pet Hair Power Brush Holder
e Top Hose Connection
2 Slide Backsaver™ wand into floor
nozzle and push tab to lock in place.
attachments, or when connecting
Hand Vac to or from the
f
Top Cord Wrap Holder
Backsaver™ Wand.
6
TOLL FREE: 1-800-798-7398
7
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Mode 2: Portable Canister
6
2
3
5
5 Attach the shorter end of Flexible
Hose to Hose Mounting Plate. Attach
the other end of the hose to the Hose
Mount on the Backsaver™ Wand.
9 Turn off the Power Button.
PORTABLE CANISTER MODE:
FOR ABOVE-THE-FLOOR
CLEANING:
Unclip the end of the hose that is
attached to the Backsaver™ Wand
4 Hold Hand Vac in one hand and use
the other hand to guide the cleaning
tool.
10 Empty Dust Cup after cleaning
and empty Dust Cup periodically
during cleaning when it appears
full. (See “Maintenance” section for
instructions.)
1
5 Turn off the Power Button and
empty Dust Cup after cleaning and
periodically during cleaning when
it appears full. (See “Maintenance”
section for instructions.)
6 Place foot on Floor Nozzle to release
from locked position and pull handle
towards you. Push the Backsaver™
Handle Release Button.
2 Depending on your cleaning needs:
NOTE: Because of the powerful
suction of the Multi-Vac, take care
when cleaning scatter-type rugs and
carpets with more delicate edges.
•
Attach the Pet Hair Power
Brush to vacuum furniture or
7 Hold Hand Vac in one hand; guide
•
Attach the 2-in-1 Crevice/
Dusting Tool to vacuum
hard-to-reach places.
the Backsaver™ Wand with the other.
8 Press the Hand Vac Power Button to
begin cleaning.
3 Hold Hand Vac in one hand and
use the other hand to guide the
cleaning tool.
8
TOLL FREE: 1-800-798-7398
9
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Mode 3: Stick Vacuum
Your Stick vacuum can be
carried by the pet hair power
brush holder.
1
4
5
2
3
CAUTION: The Power Button for
all three modes is on the Hand Vac
handle. Always turn the power OFF
before plugging and unplugging,
when adding or removing
attachments, or when connecting
Hand Vac to or from the
Backsaver™ Wand.
STICK VAC
3 With the Dust Cup end facing
upward, guide the attached Hose
Mounting plate onto the two pins on
either side of the Backsaver™ Wand.
5 Tighten the Hand Vac Locking Dial to
In Stick Vacuum Mode, you have
constant suction power with the
added swivel steering capabilities
of the Shark® Swivel Floor Nozzle:
secure onto Backsaver™ Wand.
4 Snap the shorter end of the Flexible
Hose into lower connection on the
Hand Vac (both Hose ends are the
same).
1
Remove Air Dam from Hand Vac and
place the Air Dam in the slot on the
Hand Vac exhaust filter cover.
Snap other end of the Flexible Hose
to upper connection on Backsaver™
Wand.
2
Slide Hose Mounting Plate into
grooves on the underside of the Dust
Cup so that Hose Mount assembly
covers the inlet on Hand Vac.
The single wheel of the Hand Vac
fits into the holder just below
the pins.
10
TOLL FREE: 1-800-798-7398
11
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Mode 3: Stick Vacuum
NOTE: While in Stick Vacuum mode,
you can detach the Hand Vac and
bend the Backsaver™ Wand to reach
under tight spaces( see page 8 )
9
7
6
8
6 Secure Power Cord in power clip
guide, to keep cord out of the way
while cleaning.
11 Turn off the power. Empty Dust
Cup after cleaning and periodically
during cleaning when it appears
full. (See “Maintenance” section for
instructions.)
NOTE: While in Stick Vacuum mode,
you can also detach the top end of
the hose for above-the-floor cleaning
or when trying to reach under
1
Turn power off.
2 Click Hose from upper Hose
connection.
7 Place foot on the floor nozzle and
pull handle towards you to release
upright lock.
3 Attach Pet Hair Power Brush or 2-in-1
radiators and other tight spaces.
Crevice/Dusting Tool.
NOTE: Because of the powerful
suction of the Multi-Vac, take care
when cleaning scatter-type rugs and
rugs with more delicate edges.
NOTE: Hold the Backsaver™ Handle
when detaching the top end of the
hose.
4 Press Power Button and vacuum.
8 Press Power Button on Hand Vac
5 Turn power off before returning Hose
handle to start cleaning.
to Backsaver™ Wand.
NOTE: DO NOT use Backsaver™
wand while in Stick Vacuum Mode
9 When you need to reach under
furniture, convert to portable
canister mode to use the
Backsaver™ Handle.
10 Return Hand Vac to Backsaver™
wand to continue vacuuming in Stick
Vac mode.
12
TOLL FREE: 1-800-798-7398
13
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Storing Your Multi-vac
Maintenance
3
1
3
1
STORAGE
NOTE: Empty dustcup prior
TO EMPTY DUST CUP:
1
Hold Hand Vac upright.
Your Multi-Vac can be stored as a
compact unit with the Hand Vac
attached( see “Mode 3: Stick Vac
Assembly”):
to storing your Mult-Vac ( see
maintenance section for instructions)
Regardless of what mode you
use, the Dust Cup needs to be
emptied each time you vacuum and
periodically during cleaning, when
the dust cup appears full.
2 Press Dust Cup Release Button to
remove door. Lift door off hinges
and set door aside.
3 Turn Dust Cup over a trash
1
Wrap cord around cord holders and
secure plug.
receptacle and tap gently to empty
contents.
NOTE: If Hand Vac is attached to
Hose and Backsaver™ Wand in Stick
Vac mode, remove Hand Vac first
before emptying contents.
2 Grip Backsaver™ Handle and roll unit
to storage area. Press Backsaver™
Handle Release Button to unlock top
section of Backsaver™ Handle.
4 Hold Hand Vac upright once again.
5 Set bottom hinges of Dust Cup door
into guides first; then snap door shut.
6 Check to make sure door is secure
3 Guide top section of Backsaver™
before turning on Hand Vac.
Wand forward toward the canister.
4 Roll into storage area.
14
TOLL FREE: 1-800-798-7398
15
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Maintenance
3
1
1
2
DO NOT RINSE
LIFETIME FILTERS
CLEANING PRE-MOTOR FILTERS:
7 To re-insert filters:
CLEANING EXHAUST FOAM FILTER:
Your foam filters do not need
replacement for the life of your
vacuum. However, it is important to
clean filters on both ends of Hand
Vac periodically to maintain peak
performance.
1
Grip raised brackets (on either side
of Dust Cup Release Button). Twist
Dust Cup cylinder counter-clockwise
and remove.
•
Place the Felt Filter into canister
body first.
1
Twist air-intake end of Hand Vac
counter-clockwise and remove
cylinder.
•
•
Next, place the Large Foam Filter.
2 Pull out Foam Filter.
And finally, place the Filter Frame
with Small Foam Filter tucked inside.
2 Set dustcup aside.
3 Rinse only the foam filter thoroughly
in lukewarm water until the water
runs clear.
3 Pull out gray tray with Foam Filter
DO NOT operate the vacuum without
ALL the filters in place.
8 Align locking icons of the Dust Cup
cylinder with hollow arrows on the
Hand Vac body. Twist clockwise to
lock.
insert. Pull out Foam and Felt Filters.
4 Rinse all filters thoroughly in
lukewarm water until the water runs
clear.
4 Squeeze filter and let air-dry for 24
hours before replacing; do not use
hair dryer or other heating methods
to dry.
DO NOT operate the vacuum with
WET filters.
10 Handle now aligns with raised
NOTE: The white filters will discolor
over time; this is normal and will not
affect the performance of the filters
or the vacuum.
5 Squeeze filters and let air-dry for 24
hours before replacing; do not use
hair dryer or other heating methods
to dry.
brackets of Dust Cup cylinder.
5 Re-insert Foam Filter. Grip cylinder
and align black arrows with hollow
arrows on Hand Vac. Twist clockwise
to lock.
NOTE: If Hand Vac is attached to
Hose and Backsaver™ Wand in Stick
Vac mode, remove first before
emptying contents.
6
Make sure all filters are completely
dry before inserting back into
canister body.
DO NOT operate the vacuum without
ALL the filters in place.
DO NOT operate the vacuum with
WET filters.
16
TOLL FREE: 1-800-798-7398
17
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Troubleshooting Guide
Checking for Blockages
WHERE TO ORDER PARTS
Blockages may cause your vacuum to
overheat and shut down. To prevent
this from happening, check potential
blockage areas after heavy use or if
you detect a loss of suction or poor
cleaning performance.
1-800-798-7398. NOTE: Some parts may be available at your Shark® retailer.
PROBLEM
POSSIBLE REASONS & SOLUTIONS
Check filters to see if they need cleaning. Follow instruc-
tions for rinsing and drying the 5 filters before re-inserting
back into the Hand Vac. (See “Maintenance” sections for
instructions.)
Dust cup may be full; empty dust cup.
Vacuum is not
picking up dirt.
Check Hose and Hose connections for blockages; clear
blockages if required.
If Dust Cup is empty, and attachment inlets are clear, check
for other blockages. (See “Checking for Blockages” for
instructions.)
Vacuum lifts scatter
rugs (lightweight,
movable rugs).
Because the “multi-vac” suction is powerful, take care when
vacuuming scatter-type rugs or rugs with delicately
sewn edges.
2
Check filters to see if they need cleaning. Follow
instructions for rinsing and drying the 5 filters before re-
inserting back into the Hand Vac. (See “Maintenance”
sections for instructions.)
1
Airflow is restricted.
No suction or light
suction.
Dust cup may be full; empty dust cup.
2 FILTERS (FOAM AND FELT)
1
DUST CUP – HAND VAC
Dust cup may be full. Empty dust
cup. To empty Dust Cup:
Check Hose and Hose connections for suction strength;
clear blockages if required.
Filters require rinsing every 1 month
for optimum performance. Follow
instructions for rinsing and drying
the 5 filters before using.
If Dust Cup is empty, and attachment inlets are clear, check
for other blockages. (See “Checking for Blockages” for
instructions.)
Hold Hand Vac upright. Press Dust
Cup Release Button to remove door.
Lift door off hinges and set door
aside.
(See “Maintenance” section)
To reset the Motor Thermostat:
Before continuing to vacuum, replace
Filters in the Hand Vac :
1. Move the Power Button to the “O – Off” position.
2. Unplug the vacuum.
Turn Dust Cup over a trash
receptacle and tap gently to empty
contents.
•
•
Dust Cup End (Pre-Motor)
Exhaust End (Post-Motor)
3. Check for clogged hose or filter; unclog hose and
replace filter.
Vacuum turns off
on its own.
Hold Hand Vac upright once again.
Set bottom hinges of Dust Cup door
into guides first; then snap door shut.
Wait 45 minutes for vacuum to cool; then plug in the
vacuum. Turn the Power Switch to the “I – On” position to
start the vacuum.
Check to make sure door is secure
before turning on Hand Vac.
Note: if vacuum still does not start, contact Customer
Service at: 1-800-798-7398.
18
TOLL FREE: 1-800-798-7398
19
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Checking for Blockages
FIVE (5) YEAR LIMITED WARRANTY
EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of five (5) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions
within the warranty period, return the complete appliance and accessories, freight prepaid. For
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC
will repair or replace it free of charge. Proof of purchase date and $ 9.95 to cover the cost of
return shipping and handling must be included. *
4
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or
replacement of the unit at our option. This warranty does not cover normal wear of parts and
does not apply to any unit that has been tampered with or used for commercial purposes. This
limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage
due to faulty packaging or mishandling in transit. This warranty does not cover damage or
defects caused by or resulting from damages from shipping or repairs, service or alterations to
the product or any of its parts, which have been performed by a repair person not authorized by
EURO-PRO Operating LLC.
3
This warranty is extended to the original purchaser of the unit and excludes all other legal and/
or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to
the specific obligations expressly assumed by it under the terms of the limited warranty. In no
event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature
whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or
consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe
is the problem with item. We recommend you insure the package (as damage in shipping is
not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
OWNERSHIP REGISTRATION CARD FOR
3 ACCESSORIES – CHECK
INTAKE OPENINGS
4 HOSE AND HOSE CONNECTION
TO CANISTER
CANADIAN CONSUMERS ONLY
Please complete and return within ten (10) days of purchase. The registration will enable
us to contact you in the event a product defect is discovered. By returning this card you
acknowledge to have read and understood the instructions for use, and warnings set
forth in the accompanying instructions.
•
•
•
Swivel Nozzle Floor Brush [Shark]
2-in-1 Crevice/Dusting Tool
Pet Hair Power Brush
•
•
•
Remove Hose Mounting plate.
Check the open ends of the Hose.
Check the Hose connection on the
RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec H4S 1A7
PURCHASER: ……………………………………………………………………………………………............
ADDRESS: ………………………………………………………………………………………………...............
Backsaver™ Wand.
IMPORTANT: Damages caused
while clearing or attempting to clear
blockages are not covered under
your product’s limited warranty.
•
Check the Hand Vac inlet.
WARNING: Never insert sharp
objects into any opening to clear
an obstruction.
Unplug the vacuum before checking
for blockages.
NH15 NH15C NH15W
DATE OF PURCHASE: …………………….. MODEL: ………………...................................
Reassemble all parts securely before
operating vacuum.
NAME AND ADDRESS OF STORE: …………………………………………………………………..
20
TOLL FREE: 1-800-798-7398
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|