Alarm Clock Radio
MODEL CR105
Operating Instructions
BEFORE OPERATING THIS PRODUCT, READ, UNDERSTAND, AND
FOLLOW THESE INSTRUCTIONS.
Be sure to save this booklet for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Water and Moisture - The appliance should not be used near water, e.g. near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool or the like.
6. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or
ceiling.
7. Ventilation - The appliance should be situated so that its location or position
does not interfere with its proper ventilation. For example, the appliance should
not be situated on a bed, sofa, rug or similar surface that may block the
ventilation openings, or placed in a built-in installation, such as a bookcase or
cabinet, that may impede the flow of air through the ventilation openings.
8. Heat - The appliance should be situated away from neat sources such as
radiators, heat registers, stoves, or other appliances (including amplifiers) that
produce heat..
9. Power Sources - The product should be operated only with the type of power
supply indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the
operation instructions.
10. Grounding Polarization - This product may be equipped with a polarized
alternating current line plug (a plug having one blade wider than the other). This
plug will fit into the power outlet only one way this is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
11. Power-Cord Protection - Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
12. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
13. Nonuse periods - The power cord of the appliance should be unplugged from
the outlet when left when left unused for a long period of time.
14. Object and Liquid Entry - Care should be taken so that objects do not fall and
liquids are not spilled into the product case through product openings.
15. Damage Requiring Service - Unplug this product from the wall outlet and take it
to qualified service personnel under the following conditions.
a) When the power-supply cord or plug is damaged.
b) If liquid has been spilled into, or objects have fallen into the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
c) If the product has been exposed to rain or water.
d) If the product does not operate when used according to the operating
instructions.
Adjust only those controls that are covered by the operating instructions as
an improper adjustment of other controls may interfere with the product’s
normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance-this indicates a
need for service.
16. Servicing - The user should not attempt to service the product beyond that
described in the operating instruction. All servicing should be referred to qualified
service personnel.
17. Power Lines - An outside antenna system should not be located in the vicinity of
overhead power lines, or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching power lines or circuits as
contact with them might be fatal.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the
receiver, be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static. Section 810 of the National
Electrical Code ANSI/NEFA 70 provides information with respect to proper
grounding of the mast and supporting structure, grounding conductress, location
of antenna-discharge unit, size of grounding electrodes, and requirements for
the grounding electrode (see figure).
19. Lightning - For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
20. Safety Check-Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the product is in
proper operation condition.
21. Overloading-Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fir or electric shock.
Download from Www.Somanuals.com. All Manuals Search And Download.
NEC NATIONAL ELECTRICAL CODE
Do not apply oil or petroleum products to this product.
CAUTION
Invisible laser radiation will be emitted when the product is open and interlocks are
defeated. Do not defeat the safety interlocks.
GRAPHIC SYMBOLS WITH SUPPLEMENTARY MARKINGS ARE LOCATED AT
THE BACK OF THE UNIT.
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE PROCEDURE
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION REQUIRED BY THE FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference; and (2)
this device must accept any interference received, including interference that may
cause undesirable operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with instructions, may
cause harmful interference to radio elevation reception, which can be determined by
turning the equipment off and on. Try to correct the interference by using one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS:
1. ALARM SET/OFF BUTTON
2. TIME SET BUTTON
3. HOUR SET BUTTON
4. MINUTE SET BUTTON
5. SLEEP BUTTON
6. DIAL POINTER SCALE
7. SNOOZE BUTTON
8. BAND SELECTOR SWITCH
9. ALARM (BUZZER/RADIO/AUX) SWITCH
10. FUNCTION (ON/OFF/AUTO) SWITCH
11. NIGHT LIGHT (ON/OFF/DIMMER) CONTROL
12. BATTERY COMPARTMENT
13. FM ANTENNA WIRE
14. VOLUME CONTROL
15. TUNING CONTROL
16. AUDIO IN JACK
17. AC POWER CORD
18. NIGHT LIGHT
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
Plug the AC POWER CORD to the household outlet. Make sure the voltage is
correct for safety purpose and prevent plausible damages to the set.
Connect one 9 volt battery (not included) to the battery terminals in the
BATTERY COMPARTMENT. It maintains the clock function whenever the AC
power is interrupted.
REMARK: The time display will not exhibit during power failure. But the clock
display will continue at the correct time once the main power supply is
resumed.
RADIO OPERATION
1. Set the FUNCTION SWITCH to “ON” position and the ALARM SWITCH to
“RADIO” position.
2. Set the BAND SELECTOR SWITCH to desired AM/FM.
3. Select the desired station with TUNING CONTROL.
4. Adjust the volume level with VOLUME VONTROL.
5. To obtain better FM reception, lay out the FM ANTENNA WIRE to its full
extent. NOTE: Do not connect FM antenna to outside antenna.
6. The radio can be switched off by setting FUNCTION SWITCH to the
“OFF” position.
HOW TO SET THE CLOCK
1. Press the TIME SET BUTTON simultaneously with HOUR SET BUTTON
for hour settings or MINUTE SET BUTTON for minute settings.
TO SET THE ALARM TO WAKE TO RADIO
1. Press the ALARM SET OFF BUTTON simultaneously with HOUR SET
BUTTON for hour settings or MINUTE SET BUTTON for minute settings.
Slide the BAND SELECTOR SWITCH to AM or FM position. Select a
radio station and make sure the volume is set as desired level.
2. Slide the FUNCTION SWITCH to the “AUTO” position. Slide the ALARM
SWITCH to the “RADIO/AUX” position. The ALARM RADIO ICON will light
indicating the alarm is now activated. When the actual time matches the
selected preset alarm time, the radio will automatically turn on for 1 hour
and 59 minutes and then shuts off.
TO SET THE ALARM TO WAKE TO BUZZER
1. Press the ALARM SET OFF BUTTON simultaneously with HOUR SET
BUTTON for hour settings or MINUTE SET BUTTON for minute settings.
2. Slide the FUNCTION SWITCH to the “AUTO” position. Slide the ALARM
SWITCH to the “BUZZER” position. The ALARM BUZZER ICON will light
indicating the alarm is now activated. When the actual time matches the
Download from Www.Somanuals.com. All Manuals Search And Download.
selected preset alarm time, the buzzer will automatically turn on for 1 hour
and 59 minutes and then shuts off.
SWITCHING OFF THE ALARM
1. To switch off the alarm set, just press the ALARM SET/OFF BUTTON
once and the alarm time will be reset for the next day.
2. Or slide the FUNCTION SWITCH to the “OFF” position to turn off the
alarm (the alarm time will not be reset for the next day).
SNOOZE OPERATION
The alarm can be temporarily turned off manually by pressing the SNOOZE
BUTTON. The alarm will turn on again automatically after 9 minutes. You can
repeat this process again and again for about 1 hour.
REMARK: If you want to completely shut off the alarm, please press the
ALARM OFF BUTTON.
SLEEP TIMER OPERATION
1. This clock radio is equipped with a “sleep timer” which will switch off the
radio automatically after pre-selected period from 1 hour 59 minutes to 1
minute.
2. Press SLEEP BUTTON, the display will show 0:59 sleep time. At the
same time, radio will be on and stay for 59 minutes.
3. To shorten the sleep time, press SLEEP BUTTON together with the
MINUTE SET BUTTON and TIME SET BUTTON until the desired sleep
time is shown on display.
4. After pre-selected sleep time had elapsed, the radio will switch off
automatically. To switch it off before the pre-selected sleep time gets
elapsed, press the SNOOZE BUTTON.
WORKING WITH AUDIO SOURCE
1. Use the included audio cable to join the audio source to the AUX IN JACK
on the back of the unit.
2. Slide the FUNCTION SWITCH to the “ON” position and the ALARM
SWITCH to “RADIO/AUX” position.
3. Adjust volume of the audio in order to get a better amplifying effect.
NOTE: DO NOT turn the audio source to too high volume to avoid overloading.
The output sound (radio) of the main unit will be eliminated and replaced once
the “AUDIO IN” JACK has connected to other audio source. The sound will
resume once the connective wire is removed from the jack.
If “audio in” function is in use for broadcasting music, the alarm sound will
insert into the music at the pre-set wake up time. To stop the sound, simply
Download from Www.Somanuals.com. All Manuals Search And Download.
press the ALARM SET/OFF BUTTON or slide the FUNCTION SWITCH to the
“OFF” position.
LED NIGHT LIGHT OPERATION
z
To set the LED night light to the desired level by sliding the LIGHT
CONTROL.
z
To turn off the LED night light, slide the LIGHT CONTROL to “OFF”
position until you hear the “click” sound.
SPECIFICATIONS
Frequency range:
AM 530 – 1700 KHz
FM 88 – 108 MHz
500mW
Output power:
Speaker impedance: 8 ohm x 2
Battery backup:
Power source:
9V Battery (for clock)
AC110V ~ 60Hz
WARNING: To reduce the risk of fire or electric shock does not expose this
appliance to rain or moisture.
Dripping Warning: “The product shall not be exposed to dripping or splashing
and that objects filled with liquids, such as vases, shall be places on the
product.”
Ventilation Warning: “The normal ventilation of the product shall not be
impeded for intended use.”
-
No naked flame sources, such as lighted candles, should be placed on
the apparatus;
-
Do not place the product in closed bookcases or racks without proper
ventilation.
Download from Www.Somanuals.com. All Manuals Search And Download.
|