SR 2000 IEM
SR 2050 IEM
Instruction manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Important safety instructions ............................................................................................................................................................. 2
The SR 2000 IEM and SR 2050 IEM transmitters ............................................................................................................................. 4
The frequency bank system .............................................................................................................................................................. 4
Areas of application ............................................................................................................................................................................ 5
Delivery includes ..................................................................................................................................................................................... 5
Product overview .................................................................................................................................................................................... 6
Overview of the SR 2000 IEM/SR 2050 IEM transmitter ............................................................................................................ 6
Overview of the displays ................................................................................................................................................................... 7
Putting the transmitter into operation ............................................................................................................................................. 8
Setting up the transmitter on a flat surface ................................................................................................................................. 8
Mounting the transmitter into a 19" rack ..................................................................................................................................... 8
Connecting the antennas .................................................................................................................................................................. 8
Connecting an audio source to the input sockets ...................................................................................................................... 11
Daisy chaining audio signals ........................................................................................................................................................... 11
Connecting devices to the output sockets ................................................................................................................................... 12
Connecting transmitters in a network .......................................................................................................................................... 12
Connecting the mains cable ............................................................................................................................................................ 12
Using the transmitter .......................................................................................................................................................................... 13
Switching the transmitter on/off .................................................................................................................................................. 13
Deactivating the lock mode temporarily ...................................................................................................................................... 14
Activating/deactivating the RF signal .......................................................................................................................................... 14
Monitoring the audio signal via headphones .............................................................................................................................. 15
Synchronizing transmitters and EK 2000 IEM receivers via the infra-red interface ........................................................... 15
Using the operating menu .................................................................................................................................................................. 18
The buttons ........................................................................................................................................................................................ 18
Overview of the operating menu ................................................................................................................................................... 18
Working with the operating menu ................................................................................................................................................ 20
Adjusting settings via the operating menu ................................................................................................................................... 22
The main menu “Menu” ................................................................................................................................................................... 22
The extended menu “Advanced Menu” ....................................................................................................................................... 25
Synchronizing the transmitter with the EK 2000 IEM receiver .................................................................................................. 30
Synchronizing the transmitter with an EK 2000 IEM receiver – individual operation ........................................................ 30
Synchronizing transmitters with EK 2000 IEM receivers – multi-channel operation ......................................................... 30
Using freely selectable transmission frequencies ...................................................................................................................... 31
Cleaning the transmitter ..................................................................................................................................................................... 32
Recommendations and tips ................................................................................................................................................................ 33
Accessories ............................................................................................................................................................................................. 34
If a problem occurs ... ........................................................................................................................................................................... 35
Specifications ......................................................................................................................................................................................... 36
Manufacturer Declarations ................................................................................................................................................................. 38
Index ........................................................................................................................................................................................................ 39
Supplementary information can be found on the SR 2000 IEM and SR 2050 IEM product pages on our
website at www.sennheiser.com.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
Important safety instructions
1. Read these instructions.
2. Keep these instructions. Always include these instructions when passing the transmitter
on to third parties.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, when the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. To completely disconnect this apparatus from the AC mains, disconnect the power supply
cord plug from the AC receptacle.
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain
or moisture.
17. Do not expose this equipment to dripping or splashing and ensure that no objects filled
with liquids, such as vases, are placed on the equipment.
18. The mains plug of the power supply cord shall remain readily operable.
Hazard warnings on the rear of the transmitter
The label shown on the left is attached to the rear of the transmitter. The symbols on this
label have the following meaning:
This symbol is intended to alert the user to the presence of uninsulated dangerous voltage
within the transmitter’s enclosure that may be of sufficient magnitude to constitute risk of
fire or electric shock.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety instructions
This symbol is intended to alert the user to the risk of electric shock if the transmitter is
opened. There are no user serviceable parts inside. Refer servicing to qualified personnel only.
This symbol is intended to indicate the presence of important operating and maintenance
instructions in the literature accompanying this transmitter.
Overloading
Do not overload wall outlets and extension cables as this may result in fire and electric shock.
Replacement parts
When replacement parts are required, be sure the service technician uses replacement parts
specified by Sennheiser or those having the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety check
Upon completion of any service or repairs to this device, ask the service technician to perform
safety checks to determine that the device is in safe operating order.
Danger of hearing damage due to high volumes
This is a professional transmitter. Commercial use is subject to the rules and regulations of
the trade association responsible. Sennheiser, as the manufacturer, is therefore obliged to
expressly point out possible health risks arising from use.
This transmitter is capable of producing sound pressure exceeding 85 dB(A). 85 dB(A) is the
sound pressure corresponding to the maximum permissible volume which is by law (in some
countries) allowed to affect your hearing for the duration of a working day. It is used as a
basis according to the specifications of industrial medicine. Higher volumes or longer
durations can damage your hearing. At higher volumes, the duration must be shortened in
order to prevent hearing damage. The following are sure signs that you have been subjected
to excessive noise for too long a time:
• You can hear ringing or whistling sounds in your ears.
• You have the impression (even for a short time only) that you can no longer hear high
notes.
Intended use
Intended use of the SR 2000 IEM and SR 2050 IEM transmitters includes:
• having read these instructions, especially the chapter “Important safety instructions” on
• using the device within the operating conditions and limitations described in this
instruction manual.
“Improper use” means using the device other than as described in these instructions, or
under operating conditions which differ from those described herein.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
The SR 2000 IEM and SR 2050 IEM transmitters
The SR 2000 IEM and SR 2050 IEM transmitters
With the SR 2000 IEM and SR 2050 IEM 2-channel/stereo monitoring transmitters,
musicians, video and sound amateurs, reporters/broadcasters, etc. can directly monitor the
received sound signals without troublesome cables or monitor speakers being required. In
addition, the transmitters can also be used for any application where talkback signals are to
be transmitted.
Features of the SR 2000 IEM and SR 2050 IEM transmitters:
• Optimized PLL synthesizer and microprocessor technology
• Stereo/mono selection
• HDX noise reduction system
• Switching bandwidth of up to 75 MHz
• Safe configuration of a multi-channel system using the WSM
• Easy setup of a multi-channel system using the Easy Setup Sync function
The frequency bank system
The transmitters are available in 5 UHF frequency ranges with up to 3,000 transmission
frequencies per frequency range:
Range Aw:
Range Gw:
Range Bw:
626 – 698
Range Cw:
718 – 790
Range Dw:
790 – 865
516 – 558 558 – 626
500
600
700
800
Each frequency range (Aw–Dw, Gw) offers 26 frequency banks with up to 32 channels each:
Channel 1 – frequency preset
Channel 2 – frequency preset
Frequency bank 1 ... 20
Channel 32 – frequency preset
Channel 1 – freely selectable frequency
Channel 2 – freely selectable frequency
Frequency bank U1 ... U6
Channel 32 – freely selectable frequency
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Delivery includes
Each of the channels in the frequency banks “1” to “20” has been factory-preset to a fixed
transmission frequency (frequency preset). The factory-preset frequencies within one
frequency bank are intermodulation-free. These frequencies cannot be changed.
For an overview of the frequency presets, please refer to the supplied frequency information
sheet. Updated versions of the frequency information sheet can be downloaded from the
The frequency banks “U1” to “U6” allow you to freely select and store transmission
frequencies. It might be that these transmission frequencies are not intermodulation-free
(see page 30).
Areas of application
The transmitters can be combined with the EK 2000 IEM receiver. For more information, visit
our website at www.sennheiser.com.
This receiver is available in the same UHF frequency ranges and is equipped with the same
frequency bank system with factory-preset frequencies. An advantage of the factory-preset
frequencies is that
• a transmission system is ready for immediate use after switch-on,
• several transmission systems can be operated simultaneously on the preset frequencies
without causing intermodulation interference.
Delivery includes
The packaging contains the following items:
1 SR 2000 IEM transmitter or 1 SR 2050 IEM twin transmitter
3 mains cables (with EU, UK and US plug)
1 rod antenna (SR 2000 IEM) or 2 rod antennas (SR 2050 IEM)
1 instruction manual
1 frequency information sheet
1 RF licensing information sheet
4 self-adhesive device feet
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Product overview
Product overview
Overview of the SR 2000 IEM/SR 2050 IEM transmitter
The SR 2050 IEM twin transmitter has the same operating elements as the SR 2000 IEM transmitter. All
information contained in this instruction manual refers to both transmitters.
SR 2050 IEM
ᕡ
ᕢ ᕣ
ᕤ ᕥ
ᕦ
ᕧ
ᕨ
ᕢ ᕣ
ᕤ ᕥ
ᕦ
ᕧ ᕨ
ᕡ
PEAK PEAK
PEAK PEAK
**2050**
MHz
**2050**
525.300MHz
B.Ch:
5.14
B.Ch:
5.14
Stereo Transmitter SR 2050 IEM
0
0
0
0
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
A
B
525.300
EQ
EQ
AF
I
AF II
Standard -18dB
AF
I
AF II
Standard -18dB
PUSH
PUSH
Stereo Transmitter SR 2050 IEM
PUSH
PUSH
FREQ RANGE-Dw
790-865 mHz
ART NO 627945
SER NO 251810043
IC 2099A-SR20x0
DESIGNED AND MADE IN GERMANY
ANT
A
ANT
B
Loop Out
BAL
A
Loop Out
BAL
B
B
B
+22dBu
MAX
+22dBu
MAX
BAL
AF IN
22dBu MAX
BAL
AF IN
B
A
100 240V
-
L(I)
R(II)
RF OUT
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OUT
ETHERNET RJ-45
L(I)
+
22dBu MAX R(II)
ᕩ
µ
¸ ¹
Ƹ
ƹ
ƺ
ƻ
Ƽ ƽ ¸ ¹ Ƹ
ƹ
ƺ
ƻ
ƽ
ᕢ ᕣ
ᕤ ᕥ
ᕦ
ᕧ ᕨ
ᕡ
ᕡ
SR 2000 IEM
PEAK PEAK
B.Ch:
5.14
**2000**
Stereo Transmitter SR 2000 IEM
0
0
-10 -10
-20 -20
-30 -30
-40 -40
525.300MHz
EQ
Standard -18dB
A
AF
I
AF II
PUSH
Stereo Transmitter SR 2000 IEM
PUSH
FREQ RANGE-Dw
IC 2099A-SR20x0
DESIGNED AND MADE IN GERMANY
790-865 mHz
ART NO 503841
SER NO 2518100095
Loop Out
BAL
ANT
B
+22dBu
MAX
BAL
AF IN
22dBu MAX
B
100 240V
-
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OUT
ᕩ
µ
¸ ¹
Ƹ
ƹ
ƺ
ƻ Ƽ ƽ
A
B
Operating elements – front panel
Operating elements – rear panel
³ Rack mount “ear”
¾ 3-pin mains socket
· Headphone output, ¼” (6.3 mm) jack socket (
)
µ Cable grip for power supply DC cable
» Headphone volume control
¸ LED (yellow) for network activity indication*
¿
button, backlit
¹ LAN socket (ETHERNET RJ-45)*
´ Infra-red interface
² Display panel, backlit in orange
¶ Jog dial
Ƹ Audio output left (LOOP OUT BAL L (I)),
¼” (6.3 mm) jack socket*
ƹ Audio output right (LOOP OUT BAL R (II)),
¼” (6.3 mm) jack socket*
º STANDBY button
ƺ Audio input left (BAL AF IN L (I)),
operation indication (red backlighting)
ESC function (cancel)
¼” (6.3 mm) jack/XLR-3 combo socket*
ƻ Audio input right (BAL AF IN R (II)),
¼” (6.3 mm) jack/XLR-3 combo socket*
During mono operation, the signal from the left audio
Ƽ Type plate
input (¼” (6.3 mm) jack/XLR-3 combo socket
transmitted.
ƺ)
is
ƽ Antenna output (RF OUT), BNC socket*
* These operating elements are available twice on the SR 2050 IEM twin transmitter and are labeled A and B respectively.
A designates the left-hand transmitter, B the right-hand one (seen from the front).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Product overview
Overview of the displays
After switch-on, the transmitter displays the standard display.
ብ
ቢ
ባ
ቤ
PEAK PEAK
**2050**
552.300MHz
B.Ch:
5.14
0
0
-10 -10
ቦ
-20 -20
-30 -30
-40 -40
AF I AF II
EQ
Standard -18dB
ቪ
ቧ
ቨ
ቩ
28
Display
Meaning
ቢ Audio level
Modulation of the left (AF I) and right
(AF II) audio channel with peak hold
function
PEAK PEAK
“AF I” and “AF II”
(Audio Frequency)
0
0
-10 -10
-20 -20
-30 -30
-40 -40
AF I AF II
When the transmitter is overmodulated
frequently or for extended periods of
time, the “PEAK” display is shown
inverted. In addition, the display
backlighting changes from orange to red
and “AF PEAK” flashes in alternation with
the standard display.
During mono operation, only the “AF I”
display is shown.
ባ Frequency bank and
Current frequency bank and channel number
channel
ቤ
ብ
ቦ
ቧ
ቨ
ቩ
Frequency
Current transmission frequency
Freely selectable name of the transmitter
RF signal is being transmitted
Current transmission power
Name
Transmission icon
Transmission power
Equalizer setting
Input sensitivity
Current equalizer setting
Current input sensitivity for the audio signal available at
ቪ Lock mode icon
Lock mode is activated (see page 14)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the transmitter into operation
Putting the transmitter into operation
Setting up the transmitter on a flat surface
Do not fit the device feet when mounting the transmitter into a 19" rack.
̈ Clean the base of the transmitter where you want to fix the device feet.
̈ Fit the device feet to the four corners of the transmitter.
̈ Place the transmitter on a flat, horizontal surface. Please note that the device feet can
leave stains on delicate surfaces.
Mounting the transmitter into a 19" rack
CAUTION!
Risks when rack mounting the transmitter!
When installing the device in a closed or multi-rack assembly, please consider that, during
operation, the ambient temperature, the mechanical loading and the electrical potentials will
be different from those of devices which are not mounted into a rack.
̈ Make sure that the ambient temperature within the rack does not exceed the permissible
temperature limit specified in the specifications.
̈ If necessary, provide additional ventilation.
̈ Make sure that the mechanical loading of the rack is even.
̈ When connecting to the power supply, observe the information indicated on the type
plate. Avoid circuit overloading. If necessary, provide overcurrent protection.
̈ When rack mounting, please note that intrinsically harmless leakage currents of the
individual mains units may accumulate, thereby exceeding the allowable limit value. As a
remedy, ground the rack via an additional ground connection.
̈ Slide the transmitter into the 19" rack.
ᕡ
delivery).
PEAK PEA
0
0
-10 -10
-20 -20
-30 -30
-40 -40
AF
I
AF
Connecting the antennas
You have the following options:
• For professional use, we recommend connecting a remote antenna and, if necessary, using
Sennheiser antenna accessories (see next section and the chapter “Connecting several
• If the transmitter is to be put into operation without a large amount of installation work,
you can:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the transmitter into operation
Connecting and positioning a remote antenna
Use a remote antenna when the transmitter position is not the best antenna position for
optimum transmission. You can choose between two antennas (see “Accessories” on
• A 2003 UHF passive directional broadband antenna
• A 1031 passive omni-directional broadband antenna
̈ Use a low-attenuation 50-Ω cable to connect the antenna to the transmitter.
̈ If possible, use a short antenna cable and as little connections as possible, since long
cables and many connectors lead to an attenuation of the antenna signal.
̈ Position the antenna in the same room in which the transmission takes place.
̈ Observe a minimum distance of 1 m between the antenna and metal objects (including
reinforced concrete walls).
You can connect several transmitters to the same remote antenna (see next section).
Connecting several transmitters to a remote antenna
To make multi-channel systems, you should use the AC 3200 antenna combiner (optional
accessory). The AC 3200 allows you to operate up to eight transmitters with a single antenna
without virtually any intermodulation.
Connecting the rod antenna to the rear of the transmitter
The supplied rod antenna ꢀ is suitable for all applications where the transmitter is to be put
into operation without a large amount of installation work.
ꢀ
ꢀ
ƽ
ƽ
Mounting the antennas to the front of the transmitter
To mount the antenna connections to the front of the transmitter, you require the
GA 3030 AM antenna front mount kit (optional accessory). The GA 3030 AM consists of:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the transmitter into operation
• 2 BNC extension cables (screw-in BNC socket ƿ to BNC connector ),
ƿ
• 2 antenna holders
• 4 screws,
,
• 2 washers
• 2 nuts
,
.
1
̈ Guide the BNC connector of the BNC extension cable through the hole in the rack mount
³
ƿ
̈ Screw the antenna holder
nut
to the BNC socket ƿ using the supplied washer
and
.
ƿ
the supplied screws.
If you are using the SR 2050 IEM twin transmitter:
ᕡ
̈ Mount the second BNC extension cable in the same way.
³
1
ƿ
³
ƿ
̈ Slide the transmitter into the 19" rack.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the transmitter into operation
̈ Connect the rod antennas ꢀ to the two BNC sockets ƿ.
ꢀ
ƿ
Connecting an audio source to the input sockets
PUSH
Stereo Trans
PUSH
FREQ RANGE-Dw
790-865 mHz
̈ Use a suitable cable to connect the output of the audio source (e.g. mixing console) to the
IC 2099A-SR20x0
ART NO 503841
SER NO 2518100095
DESIGNED AND MADE IN GERM
ANT
BAL
AF IN
L(I)
+
22dBu MAX
R(II)
RF OUT
̈ Adjust the output level of your audio source.
ƺ
ƻ
̈ Via the operating menu, adjust the transmitter’s input sensitivity. The input sensitivity is
You can connect several transmitters to the same audio source (see next chapter).
Daisy chaining audio signals
You can transmit the same audio signal (e.g. the sum of all audio channels of a mixing
console) to several receivers of a multi-channel system. To do so, you have to daisy chain this
the two channels L (I) or R (II). The second channel allows you to transmit an individual audio
signal (e.g. the instrument of a musician). Using the balance setting on the receiver, you can
then adjust the relative levels of the sum of all audio channels and the individual audio signal.
For this, the transmitter has to be set to stereo mode and the receiver to Focus mode.
To daisy chain an audio signal from one transmitter to the next:
̈ Route
a
signal from the audio source to the input socket (in this example:
PUSH
PUSH
Stereo Transmitter SR 2000 IEM
Stereo Transmitter SR 2000 IEM
PUSH
FREQ RANGE-Dw
790-865 mHz
ART NO 503841
SER NO 2518100095
PUSH
PUSH
IC 2099A-SR20x0
DESIGNED AND MADE IN GERMANY
FMO
IC 2099A-SR20x0
-
7-6
52039851
21100395
DESIGNED AND MADE IN GERMANY
Loop Out
BAL
ANT
ANT
A
Loop Out
BAL
B
Loop Out
BAL
A
B
B
+22dBu
MAX
B
BAL
AF IN
22dBu MAX
+22dBu
MAX
+22dBu
MAX
BAL
AF IN
22dBu MAX
BAL
AF IN
22dBu MAX R(II)
100
-
240V
L(I)
+
R(II)
RF OUT
B
A
50/60Hz 0.2
A
ETHERNET RJ-45
L(I)
R(II)
100
-
240V
A
B
C
50/60Hz 0.2
A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OUT
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
RF OU
A
B
C
PUSH
PUSH
Stereo Transmitter SR 2000 IEM
PUSH
PUSH
Stereo Transmitter SR 2000 IEM
PUSH
FREQ RANGE-Dw
790-865 mHz
F-
7085
IC 2099A-SR20x0
IC 2099A-SR20x0
ART NO 503841
SER NO 2518100095
DESIGNED AND MADE IN GERMANY
A65073841
S5804095
DESIGNED AND MADE IN GERMANY
Loop Out
BAL
ANT
ANT
A
Loop Out
BAL
B
ANT
B
Loop Out
BAL
A
B
B
+22dBu
MAX
B
BAL
AF IN
22dBu MAX
+22dBu
MAX
+22dBu
MAX
BAL
AF IN
22dBu MAX
BAL
AF IN
1
0
0
-
2
4
0
V
B
A
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OUT
1
0
0
-
2
4
0
V
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OU
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
2
2
d
B
u
M
A
X
R
(
I
I
)
RF OUT
PUSH
PUSH
Stereo Transmitter SR 2000 IEM
FREQ RANGE-Dw
790-865 mHz
ART NO 503841
SER NO 2518100095
PUSH
PUSH
Stereo Transmitter SR 2000 IEM
PUSH
IC 2099A-SR20x0
9-6
IC 2099A-SR20x0
I29-20
DESIGNED AND MADE IN GERMANY
T 65073841
5804095
DESIGNED AND MADE IN GERMANY
Loop Out
BAL
ANT
ANT
A
Loop Out
BAL
B
ANT
B
Loop Out
BAL
A
B
B
+22dBu
MAX
BAL
AF IN
22dBu MAX
B
+22dBu
MAX
+22dBu
MAX
BAL
AF IN
22dBu MAX
BAL
AF IN
22dBu MAX R(II)
1
0
0
-
2
4
0
V
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
ROU
B
A
1
0
0
-
2
4
0
V
50/60Hz 0.2A
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
R(II)
RF OT
ETHERNET RJ-45
L(I)
R(II)
L(I)
+
RF OUT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Putting the transmitter into operation
̈ Repeat for the other transmitters.
only when the transmitter is switched on and powered.
Connecting devices to the output sockets
Stereo Transmitter SR 2000 IEM
FREQ RANGE-Dw
IC 2099A-SR20x0
̈ Use a suitable cable to connect the audio input of a device (e.g. a mixing console or an
790-865 mHz
ART NO 503841
DESIGNED AND MADE IN GERMANY
SER NO 2518100095
Loop Out
BAL
A
ANT
B
B
+22dBu
MAX
L(I)
R(II)
RF OUT
ETHERNET RJ-45
Ƹ
ƹ
ƺ
transmitter is switched on and powered.
Connecting transmitters in a network
You can connect several transmitters in a network. The transmitters are remote controlled via
a PC running the “Wireless Systems Manager” (WSM) software. This software will assist in
the quick and safe configuration of multi-channel systems.
The “Wireless Systems Manager” (WSM) software can be downloaded from our
Stereo Transmitter SR 2000 IEM
FREQ RANGE-Dw
IC 2099A-SR20x0
790-865 mHz
DESIGNED AND MADE IN GERMANY
ART NO 503841
SER NO 2518100095
Loop Out
BAL
A
ANT
B
̈ Connect your transmitters to an Ethernet switch.
+22dBu
MAX
L(I)
R(II)
RF OUT
ETHERNET RJ-45
̈ Connect a PC to the Ethernet switch.
¸ ¹
When a transmitter is properly connected to the Ethernet switch or the PC, the yellow
For further information on network operation using the WSM, refer to page 30.
Connecting the mains cable
CAUTION!
Damage due to electric current!
If you connect the transmitter to an unsuitable power supply, this can cause damage to the
device.
̈ Use the supplied mains cable to connect the transmitter to the mains (100 to 240 V AC,
50 or 60 Hz).
̈ Ensure a reliable mains ground connection of the transmitter – especially when you are
using multi-outlet power strips or extension cables.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the transmitter
̈ Plug the mains plug into the wall socket.
B
100 240V
-
50/60Hz 0.2A
ETHERNET RJ-45
¾
µ
Using the transmitter
To establish a transmission link, proceed as follows:
1. Switch the transmitter on (see next section).
2. Switch the EK 2000 IEM receiver on (see the instruction manual of the receiver).
The transmission link is established.
It is vital to observe the notes on frequency selection on page 30.
If you cannot establish a transmission link between the transmitter and the EK 2000 IEM
Switching the transmitter on/off
To switch the transmitter on (online operation):
0**
The transmitter switches on and the standard display appears.
The transmitter transmits an RF signal and the transmission icon
is displayed.
º
To switch the transmitter on and to deactivate the RF signal on switch-on (offline operation):
panel.
̈ Press the jog dial.
The transmission frequency is displayed but the transmitter does not transmit an
RF signal. The transmission icon
is not displayed. In addition, the display
backlighting changes from orange to red and “RF Mute” flashes in alternation
with the standard display.
PEAK PEAK
**2000**
552.300MHz
B.Ch:
5.14
0
0
-10 -10
ቦ
-20 -20
-30 -30
-40 -40
AF I
EQ
Standard -18dB
AF II
Use this function to prepare a transmitter for use during live operation without
causing interference to existing transmission links.
To activate the RF signal:
“RF Mute Off?” appears on the display panel.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the transmitter
̈ Press the jog dial.
The transmission icon
is displayed again.
To switch the transmitter to standby mode:
The transmitter switches to standby mode.
(ESC function) and return you to the standard display.
To completely switch the transmitter off:
̈ Disconnect the transmitter from the mains by unplugging the mains plug from the wall
socket.
Deactivating the lock mode temporarily
page 25). If the lock mode is activated, you have to temporarily deactivate it In order to be
able to operate the transmitter:
̈ Press the jog dial.
“Locked” appears on the display panel.
̈ Turn the jog dial.
“Unlock?” appears on the display panel.
̈ Press the jog dial.
The lock mode is temporarily deactivated.
– When you are in the operating menu, the lock mode remains deactivated until
you exit the operating menu.
– When the standard display is shown, the lock mode is automatically activated
after 10 seconds.
PEAK PEAK
**2000**
552.300MHz
B.Ch:
5.14
0
0
-10 -10
-20 -20
-30 -30
-40 -40
AF I
EQ
Standard -18dB
AF II
ቪ
Activating/deactivating the RF signal
To deactivate the RF signal:
̈ When the standard display is shown on the display panel, press the STANDBY
button.
“RF Mute On?” appears on the display panel.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the transmitter
̈ Press the jog dial.
The RF signal is deactivated. The transmission icon
is not displayed. In addition,
the display backlighting changes from orange to red and “RF Mute” flashes in
alternation with the standard display.
To activate the RF signal:
̈ Press the STANDBY button.
“RF Mute Off?” appears on the display pane.
̈ Press the jog dial.
The RF signal is activated and the transmission icon
backlighting changes from red to orange.
is displayed. The display
To deactivate the RF signal on switch-on:
Monitoring the audio signal via headphones
CAUTION!
Danger of hearing damage!
Listening at high volume levels for long periods can lead to permanent hearing defects.
headphones on.
̈ Do not continuously expose yourself to high volumes.
PEAK PEAK
Stereo Transmitter SR 2000 IEM
0
0
-10 -10
-20 -20
-30 -30
-40 -40
AF
I
AF II
̈ Gradually increase the volume and monitor the audio signal with the lowest possible
volume.
ᕢ
ᕣ
Synchronizing transmitters and EK 2000 IEM receivers via the
infra-red interface
Synchronization allows you to quickly and easily transfer transmitter and receiver settings
from one device to the other, especially if you want to configure a multi-channel system.
There are two transfer directions:
1. Easy Setup Sync: Transfer from the receiver to one or several transmitters
Once you have performed a frequency preset scan with a receiver, you can use the Easy
Setup Sync function to transfer unused frequency presets from the receiver to the
transmitters via the infra-red interface. In order to set up a multi-channel system, you
use the diversity receiver to transfer the first unused channel from the selected
frequency bank to the first transmitter and the next unused channel to the second
transmitter and so on, thus ensuring that all transmitters of a multi-channel system
operate on suitable frequencies.
2. Sync: Transfer from a transmitter to a receiver
Once you have selected and set the desired receiver settings on the transmitter (either
manually or using the Easy Setup Sync function), you transfer these settings to a
receiver. This configures the receiver and establishes a transmission link between
transmitter and receiver.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the transmitter
When carrying out the Sync function, the transmitter’s current frequency bank and
channel setting as well as the receiver parameters adjusted via the “Sync Settings”
interface.
Carrying out an Easy Setup Sync or a Sync function
The following assumes that you are using the Easy Setup Sync function for setting up a multi-
channel system. You can also use the Easy Setup Sync function for establishing a
transmission link between one transmitter and one EK 2000 IEM receiver.
Easy Setup Sync
Sync
̈ Switch all transmitters and one receiver ̈ Switch the transmitter and the receiver
on. on.
̈ On all transmitters, call up the “Easy ̈ Press the
Setup” menu item.
transmitter.
The icon appears on the display
panel of the transmitter.
The text “Easy Setup Sync” and the
icon appear on the display panels of the
transmitters.
The RF signal of the transmitters is
automatically deactivated.
̈ Use your receiver to perform a frequency
–
preset scan (Scan New List).
̈ Select a channel within a frequency bank
with
a
sufficient number of unused
channels (Current List).
´
ᕥ
ᕤ
̈ Place the infra-red interface of the ̈ Place the infra-red interface of the
receiver (see the instruction manual of
the receiver) in front of the infra-red
receiver (see the instruction manual of
the receiver) in front of the infra-red
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the transmitter
Easy Setup Sync
Sync
The first unused frequency preset is
transferred from the receiver to the
transmitter.
The current frequency bank and channel
setting as well as the parameters
adjusted via the “Sync Settings” menu
item are transferred from the transmitter
to the receiver.
When the transfer is completed, the
display panel of the transmitter displays
the numbers of the transferred
frequency bank and channel.
When the transfer is completed, “
”
appears on the display panel of the
transmitter. The transmitter then
switches back to the standard display.
Please note that the transmitter does not
automatically store the frequency bank
and channel setting.
The
transferred
parameters
are
automatically adjusted and stored by the
receiver. The transmission link between
transmitter and receiver is now
established.
̈ Place the infra-red interface of the
diversity receiver in front of the infra-red
interfaces of the remaining transmitters,
one after the other.
–
–
In each case, the next unused frequency
preset is transferred from the receiver to
the transmitter.
Either:
̈ Store the frequency bank and channel
setting by pressing the jog dial on your
transmitters.
The RF signal is activated. You can carry
out the Sync function (see right-hand
column) at a later time to establish a
transmission link between transmitters
and receivers.
Or:
–
̈ Immediately synchronize your receivers
with your transmitters by carrying out
the Sync function (see right-hand
column).
The
icon in the left lower corner of
the transmitter display indicates that the
Sync function can be carried out. The
transmission link between transmitters
and receivers is established.
–
To cancel the transfer:
̈ Press the STANDBY button on the
transmitter.
“ ” appears on the display panel of the
transmitter. “ ” also appears if no
suitable receiver was found.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the operating menu
Using the operating menu
A special feature of the Sennheiser 2000 series is the consistent, intuitive menu structure of
transmitters and receivers. As a result, adjustments to the settings can be made quickly –
even in stressful situations, for example on stage or during a live show or presentation.
The buttons
Button
Press the STANDBY button • Switches the transmitter on and off
• Cancels the entry and returns to the standard display
Function of the button
(ESC function)
• Activates/deactivates the RF signal
(special function, see page 14)
Press the jog dial
Turn the jog dial
• Changes from the standard display to the operating menu
• Calls up a menu item
• Enters a submenu
• Stores the settings and returns to the operating menu
• Changes to the next/previous menu item
• Changes the setting of a menu item
Overview of the operating menu
Extended menu
“Advanced Menu”
Main menu
“Menu”
“Sync Settings”
Tune
Balance
Squelch
Mode
High Boost
Auto Lock
Limiter
Exit
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
AutoLock
Advanced
Exit
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
“Warnings”
AF Peak
RF Mute
Exit
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the operating menu
Display
Function of the menu item
Page
Main menu “Menu”
Sensitivity
Adjusts the input sensitivity (0 to –42 dB in steps of 3 dB)
Selects mono or stereo operation
Mode
Easy Setup
Deactivates the RF signal and activates the Easy Setup Sync
function
Frequency Preset Sets the frequency bank and the channel
Name
Enters a freely selectable name
Equalizer
Changes the frequency response of the output signal using a
graphic equalizer (+/– 12 dB in steps of 2.4 dB)
AutoLock
Advanced
Exit
Activates/deactivates the automatic lock mode
Calls up the extended menu “Advanced Menu”
–
Exits the operating menu and returns to the standard display
Extended menu “Advanced Menu”
Tune
Sets the transmission frequencies for the frequency banks
“U1” to “U6”
Sets the frequency bank, the channel and the transmission
frequency (frequency banks “U1” to “U6”)
Sync Settings
Adjusts the receiver parameters and activates/deactivates
their transfer to the receivers
RF Power
Adjusts the transmission power (Low, Standard or High)
Calls up “Warnings” (see below)
Warnings
LCD Contrast
Adjusts the contrast of the display panel (adjustable in 16
steps)
Reset
Resets the settings made in the operating menu
Adjusts the IP address of the transmitter
IP-Address
Software Revision Displays the current software revision
Exit
Exits the extended menu “Advanced Menu” and returns to the
main menu
–
“Warnings”
Activates/deactivates warnings (color change and warning messages)
AF Peak
RF Mute
Exit
Audio overmodulation
RF signal is deactivated
Exits “Warnings” and returns to the extended menu
“Advanced Menu”
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the operating menu
Working with the operating menu
If the lock mode is activated, you have to deactivate it In order to be able to work with
the operating menu (see page 14).
By way of example of the “Frequency Preset” menu, this section describes how to use the
operating menu.
Changing from the standard display to the operating menu
̈ Press the jog dial.
The standard display is replaced by the main menu. The last selected menu item
is displayed.
Selecting a menu item
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
̈ Turn the jog dial to change to the “Frequency Preset” menu item.
The current setting of the selected menu item is displayed:
PEAK PEAK
Menu
0
0
Easy Setup
Frequency Preset
Name
-10 -10
-20 -20
-30 -30
-40 -40
AF
AF
B. Ch:
1. 1
Changing and storing settings
PEAK
0
PEAK PEAK
PEAK
PEAK Frequency Preset
0
PEAK Menu
Frequency Preset
B.Ch: 1. 1
0
0
0
0
-10 -10 Easy Setup
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
Frequency Preset
Name
B.Ch: 2.
3
519.150 MHz
525.450 MHz
AF
AF
AF
AF
AF
AF
B.Ch: 1. 1
Call up “Frequency
Preset”
Select the frequency
bank and confirm
Select the channel;
store the setting
“Stored”
̈ Press the jog dial to call up the menu item.
̈ Turn the jog dial to set the frequency bank.
̈ Press the jog dial to confirm your selection.
̈ Turn the jog dial to set the channel.
̈ Press the jog dial to store the setting.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the operating menu
By briefly turning the jog dial to the left or right, the display jumps either forwards
or backwards to the next menu item or setting. If you turn the jog dial to the left or
right and hold it in this position, the display cycles continuously (“fast search”
function).
Canceling an entry
̈ Press the STANDBY button to cancel the entry.
The standard display appears on the display panel.
To subsequently return to the last edited menu item:
̈ Press the jog dial repeatedly until the last edited menu item appears.
Exiting a menu item
Menu
Sensitivity
Mode
̈ Change to the “Exit” menu item.
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
̈ Confirm your selection.
You return to the next higher menu level or you exit the operating menu and
return to the standard display.
To directly return to the standard display:
̈ Press the STANDBY button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
Adjusting settings via the operating
menu
The main menu “Menu”
Adjusting the input sensitivity – “Sensitivity”
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
PEAK PEAK
PEAK PEAK
PEAK PEAK
Menu
Sensitivity
Sensitivity
0
0
0
0
0
0
-10 -10 Exit
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
-20 -20
Sensitivity
Mode
– 18 dB
– 15 dB
-30 -30
-40 -40
AF
AF
AF
AF
AF
AF
– 18dB
Call up “Sensitivity”
Select the desired
setting
Store the setting
“Stored”
Adjustment range: 0 to –48 dB, adjustable in steps of 3 dB
Via the “Sensitivity” menu item, you can adjust the transmitter’s input sensitivity to the
output signal of the audio source. The adjusted input sensitivity is common for both audio
inputs of the transmitter.
The audio level display “AF” always indicates the audio level, even if the transmitter
is muted, e.g. allowing you to check the adjusted sensitivity before live operation.
Input sensitivity
is adjusted ...
Effect/display
... too high
Close talking distances, speakers with loud voices or loud music
passages cause overmodulation in the transmission link.
the duration of the overmodulation.
... correctly
... too low
only during the loudest passages.
The transmission link is undermodulated. This results in a signal with
high background noise.
Selecting mono or stereo operation – “Mode”
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
PEAK PEAK
PEAK PEAK
PEAK
0
-10
Menu
Mode
Mode
0
0
0
0
-10 -10 Sensitivity
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
-20
Stereo
Mono
Mode
Easy Setup
-30
-40
AF
AF
AF
AF
AF
Stereo
Call up “Mute Mode”
Select the desired
setting
Store the setting
“Stored”
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
̈ Select “Stereo” if you want to transmit the audio signals from the left and right audio
̈ Select “Mono” if you only want to transmit the audio signal from the left audio input
During mono operation, you have to deactivate the pilot tone evaluation on your
EK 2000 IEM receiver in order to ensure that the receiver outputs the same signal on
channel I and II.
Starting synchronization – “Easy Setup”
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
AutoLock
Advanced
Exit
PEAK PEAK
PEAK PEAK
Menu
Easy Setup
0
0
0
0
-10 -10 Mode
-10 -10
-20 -20
-30 -30
-40 -40
-20 -20
Easy Setup
-30 -30
-40 -40
sync
Frequency Preset
AF
AF
AF
AF
Call up “Easy Setup”
Infra-red transmission
is awaited
̈ Call up “Easy Setup” to transfer an unused frequency preset from the EK 2000 IEM
receiver to the transmitter via the infra-red interface (see page 15).
The RF signal of the transmitter is automatically deactivated (“RF Mute” flashes) and the
transmitter awaits the data transfer.
If you do not want to start the transfer or to chancel the transfer:
̈ Press the STANDBY button.
Selecting the frequency bank and the channel manually – “Frequency Preset”
Menu
PEAK
0
PEAK PEAK
PEAK
PEAK Frequency Preset
0
PEAK Menu
Frequency Preset
B.Ch: 1. 1
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
0
0
0
0
-10 -10 Easy Setup
-20 -20
-30 -30
-40 -40
AF
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
Frequency Preset
Name
B.Ch: 2.
3
519.150 MHz
525.450 MHz
AF
AF
AF
AF
AF
B.Ch: 1. 1
Call up “Frequency
Preset”
Select the frequency
bank and confirm
Select the channel;
store the setting
“Stored”
When you are in the “Frequency Preset” menu item, the RF signal is deactivated.
Overview of the frequency banks and channels:
Frequency bank
Channels
Type
“1” to “20”
up to 32 per
System bank: frequencies are factory-preset
frequency bank
“U1” to “U6”
up to 32 per
User bank: frequencies are freely selectable
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
When setting up multi-channel systems, please observe the following:
Only the factory-preset frequencies within one frequency bank (“1” to “20”) are
intermodulation-free. It is vital to observe the notes on frequency selection on
Entering a name – “Name”
Menu
PEAK PEAK
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK
PEAK Name
0
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
Menu
PEAK Name
0
0
0
0
-10 -10 Frequency Preset
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
L ichael
Michael
Name
Equalizer
AF
AF
AF
AF
AF
AF
Lichael
Call up “Name”
Enter a character and
confirm
Enter a character;
store the setting
“Stored”
Via the “Name” menu item, you can enter a freely selectable name (e.g. the name of the
performer) for the transmitter. The name is displayed on the standard display. The name can
consist of up to 8 characters such as:
• letters (without pronounciation marks),
• numbers from 0 to 9,
• special characters and spaces.
To enter a name, proceed as follows:
̈ Turn the jog dial to select a character.
̈ Press the jog dial to change to the next segment/character or to store the
complete entry.
Using the equalizer
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK PEAK
PEAK
PEAK Equalizer
0
PEAK Menu
Name
Equalizer
Auto Lock
Equalizer
EQ
0
0
0
0
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
EQ
active
active
AF
AF
AF
AF
AF
AF
EQ
Call up “Equalizer”
Select the desired
setting and confirm
Select the desired
setting; store the setting
“Stored”
Adjustment range: +/− 12 dB, adjustable in steps of 2.4 dB
You can change the treble and bass of the audio output signal in 5 frequency ranges.
Display
Frequency range
20 - 100 Hz
100 - 300 Hz
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
Display
Frequency range
300 Hz - 1 kHz
1 - 3 kHz
3 - 10 kHz
To change the treble and bass of the audio output signal, proceed as follows:
̈ Turn the jog dial to boost or cut the frequency range.
̈ Press the jog dial to change to the next frequency range or to store the complete
entry.
Activating/deactivating the automatic lock mode – “Auto Lock”
Menu
Sensitivity
Mode
Easy Setup
Frequency Preset
Name
Equalizer
Auto Lock
Advanced
Exit
PEAK PEAK
PEAK PEAK
PEAK PEAK
Menu
Auto Lock
Auto Lock
0
0
0
0
0
0
-10 -10 Equalizer
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
Inactive
Active
Auto Lock
Advanced
AF
AF
AF
AF
AF
AF
Inactive
Call up “Auto Lock”
Select the desired
setting
Store the setting
“Stored”
The lock mode prevents that the plug-on transmitter is accidentally switched off or
programed during operation. The lock mode icon on the standard display indicates that
the lock mode is activated. For information on how to use the lock mode, refer to page 14.
̈ Turn the jog dial to select the desired setting.
The extended menu “Advanced Menu”
Setting the transmission frequencies and the frequency banks “U1” to “U6” –
“Tune”
Advanced Menu
Tune
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
When you have selected one of the system banks and then select the “Tune” menu,
the transmitter automatically switches to channel 1 of the frequency bank “U1”. In
this case, “U1.1” briefly appears on the display panel.
Upon delivery, the channels of the frequency banks “U1” to “U6” are not assigned a
transmission frequency.
When you are in the “Tune” menu item, the RF signal is deactivated.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
Via the “Tune” menu item, you can:
1. set a transmission frequency to be stored in the current channel of the frequency bank
(“U1” to “U6”)
2. or select a frequency bank (“U1” to “U6”) and a channel and assign this channel a
transmission frequency.
Setting a transmission frequency for the current channel
Advanced Menu
Tune
̈ Turn the jog dial until the “Tune” menu item appears.
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
̈ Press the jog dial.
The frequency selection appears.
PEAK
0
PEAK
0
PEAK
0
PEAK Tune
PEAK Tune
PEAK Advanced Menu
0
0
0
-10 -10 Exit
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
552.300 MHz
553.300 MHz
-20 -20
-30 -30
-40 -40
Tune
Sync Settings
B.Ch: U1.
1
AF
AF
AF
AF
B.Ch: U1.
1
AF
AF
532.300 MHz
Call up “Tune”
(special function)
Select the MHz value
and confirm
Select the kHz value;
store the setting
“Stored”
It is vital to observe the notes on frequency selection on page 30.
̈ Set the desired frequency.
̈ Press the jog dial.
Your settings are stored. The “Tune” menu item appears.
Selecting a frequency bank and a channel and assigning this channel a
transmission frequency
Advanced Menu
Tune
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
̈ Turn the jog dial until the “Tune” menu item appears.
̈ Keep the jog dial pressed until the frequency bank selection appears.
IP-Address
Software Revision
Exit
PEAK
0
-10 -10 Exit
-20 -20
-30 -30
-40 -40
AF
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK Tune
PEAK Tune
PEAK Advanced Menu
0
0
0
552.300 MHz
552.300 MHz
Tune
Sync Settings
B.Ch: U2.
6
B.Ch: U1.
1
AF
AF
AF
AF
AF
552.300 MHz
Call up “Tune”
(special function)
Select the frequency
bank and confirm
Select the channel;
store the setting
“Stored”
̈ Set the desired frequency bank.
̈ Press the jog dial.
The channel selection appears.
̈ Set the desired channel.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
̈ Press the jog dial.
The frequency selection appears.
̈ Set the desired frequency.
̈ Press the jog dial.
Your settings are stored. The “Tune” menu item appears.
Adjusting the receiver parameters and activating/deactivating their transfer to
the receiver – “Sync Settings”
Advanced Menu
Tune
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
Via the “Sync Settings” submenu, you can adjust the following parameters for the
EK 2000 IEM receiver.
Menu item Transferred receiver parameter
IP-Address
Software Revision
Exit
Balance
Squelch
Mode
Balance or Focus setting (“−15”/“+15”)
Squelch setting (“5 dB” ... “25 dB”)
Audio mode setting (“Stereo”/“Focus”)
High Boost Treble boost setting for output signal (“flat”/“High boost” (8 dB at 10 kHz))
Auto Lock
Limiter
Exit
Lock mode setting (“Active”/“Inactive”)
Limiter setting (“−18 dB”, “−12 dB”, “−6 dB”, “Off”)
Exits the “Sync Settings” submenu and returns to the extended menu
“Advanced Menu”
You can specify for each parameter whether it is to be transferred to the receiver during
synchronization.
Parameter
Transfer is ...
... deactivated
PEAK
0
-10
40
30
20
10
-20
-30
-40
AF
-60 dB
-60 dB
Sync
Sync
RF
... activated
PEAK
0
40
30
20
10
-10
-20
-30
-40
AF
RF
By pressing the
¿ button on the transmitter, the parameters are transferred from the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
Adjusting the transmission power – “RF Power”
Advanced Menu
Tune
PEAK
0
PEAK
0
PEAK PEAK
PEAK RF Power
RF Power
PEAK Advanced Menu
0
0
0
0
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
-10 -10 Sync Settings
-10 -10
-20 -20
-30 -30
-40 -40
-10 -10
-20 -20
-30 -30
-40 -40
-20 -20
Low
RF Power
Warnings
Standard
-30 -30
-40 -40
AF
AF
AF
AF
AF
AF
Standard
Call up “RF Power”
Select the desired
setting
Store the setting
“Stored”
Via the “RF Power” menu item, you can adjust the transmission power in three steps (Low,
Standard, High).
It is vital to observe the notes on the enclosed frequency information sheet!
Activating/deactivating warning messages – “Warnings”
Advanced Menu
Tune
Via the “Warnings” menu item, you can activate or deactivate different warning messages.
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
Warning message with color
change on the standard display
Setting
AF Peak
RF Mute
Trigger
“AF Peak”
Audio overmodulation
RF signal is deactivated (see page 14)
“RF Mute”
Adjusting the contrast of the display panel – “LCD Contrast”
You can adjust the contrast of the display panel in 16 steps.
Resetting the settings made in the operating menu – “Reset”
Advanced Menu
Tune
PEAK PEAK
PEAK PEAK
Advanced Menu
Reset
0
0
0
0
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
-10 -10 LCD Contrast
-10 -10
-20 -20
-30 -30
-40 -40
-20 -20
Reset
IP-Address
Yes
-30 -30
-40 -40
AF
AF
AF
AF
Call up “Reset”
Select the desired
setting; apply the setting
“Stored”
When resetting the settings made in the operating menu, only the selected settings for the
pilot tone and for the frequency banks “U1” to “U6” remain unchanged. For an overview of
the factory-preset default settings, refer to the enclosed frequency information sheet.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting settings via the operating menu
Adjusting the network configuration – “IP Address”
Advanced Menu
Tune
PEAK PEAK
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK
0
-10 -10
-20 -20
-30 -30
-40 -40
PEAK IP-Address
PEAK IP-Address
Advanced Menu
Reset
IP-Address
0
0
0
0
Sync Settings
RF Power
Warnings
LCD Contrast
Reset
IP-Address
Software Revision
Exit
-10 -10
-20 -20
-30 -30
-40 -40
Manual
192.168.178.100
Manual
192.168.178.100
Software Revision
192.168.178.100
AF
AF
AF
AF
AF
AF
00-11-D8-B0-F4-33
00-11-D8-B0-F4-33
Enter the IP address;
store the setting
Call up “IP-Address”
Select the mode and
confirm
“Stored”
You can either automatically allocate or manually enter an IP address. This menu item also
shows the transmitter’s unique and unchangeable MAC address. In order to ensure safe
recommend using automatic allocation of IP addresses.
Displaying the software revision – “Software Revision”
You can display the current software revision of the transmitter.
̈ For information on software updates, visit the corresponding product page on our website
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronizing the transmitter with the EK 2000 IEM receiver
Synchronizing the transmitter with the EK 2000 IEM
receiver
When synchronizing your transmitter with the EK 2000 IEM receiver, please observe the
following:
̈ Only use a transmitter and a receiver from the same frequency range (see the
type plates on the transmitter and the receiver).
̈ Make sure that the desired frequencies are listed in the enclosed frequency
information sheet. You can also contact your Sennheiser partner who will be
pleased to calculate intermodulation-free frequencies for you.
̈ Make sure that the desired frequencies are approved and legal in your country
and, if necessary, apply for an operating license.
̈ The frequency information sheet can also be downloaded from the corresponding
Synchronizing the transmitter with an EK 2000 IEM receiver –
individual operation
Upon delivery, transmitter and receiver are synchronized with each other. If, however, you
cannot establish a transmission link between transmitter and receiver, you have to
synchronize the channels of the devices:
The transmitter is set to a suitable frequency.
This establishes a transmission link between the transmitter and the receiver.
Alternatively, you can set the channel on the transmitter manually:
̈ Make sure that you set the transmitter to the same frequency bank and the same channel
as the receiver.
Synchronizing transmitters with EK 2000 IEM receivers – multi-
channel operation
Network operation In multi-channel operation, the transmitters are remote controlled via a PC running the
“Wireless Systems Manager” (WSM) software.
Advantages of controlling the transmitters via the “Wireless Systems Manager”
(WSM) software:
• Detailed overview of all transmission and receiving channels
• Remote control of all transmitters in the network
Stereo
T
r
a
n
s
m
i
t
t
e
r
S
R
2
0
5
0
I
E
M
S
t
e
r
e
o
T
r
a
n
s
m
i
t
t
e
r
S
R
2
0
5
0
I
E
M
̈ Switch your transmitters and your PC on.
S
t
e
r
e
o
T
r
a
n
s
m
i
t
t
e
r
S
R
2
0
5
0
I
E
M
̈ Launch the “Wireless Systems Manager” (WSM) software.
̈ To set up your multi-channel system, proceed as described in the instruction manual of
the “Wireless Systems Manager” (WSM) software.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Synchronizing the transmitter with the EK 2000 IEM receiver
Operation without ̈ First carry out the Easy Setup Sync function (see table on page 16, left-hand column).
network
The transmitter is set to a suitable frequency.
̈ Then carry out the Sync function once for each transmitter/receiver pair (see table on
page 16, right-hand column).
This establishes a transmission link between the transmitter and the receiver.
Using freely selectable transmission frequencies
You can also freely select the frequencies and store these frequencies in the frequency banks
“U1” to “U6”.
If you want to use the frequency banks “U1” to “U6”:
and the type plates of the devices).
To ensure that the desired frequencies are intermodulation-free:
̈ Set each transmitter to the same frequency bank.
̈ Synchronize a receiver with your transmitter (
, see page 16).
OR
̈ Manually set the receiver to the same frequency bank, channel and frequency that you set
on the transmitter.
̈ Repeat for the remaining transmitters and receivers as described above.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning the transmitter
Cleaning the transmitter
CAUTION!
Liquids can damage the electronics of the transmitter!
Liquids entering the housing of the transmitter can cause a short-circuit and damage the
electronics.
̈ Keep all liquids away from the transmitter.
̈ Do not use any solvents or cleansing agents.
̈ Before cleaning, disconnect the transmitter from the mains.
̈ Use a cloth to clean the transmitter from time to time.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommendations and tips
Recommendations and tips
... for optimum reception
• Transmission range depends to a large extent on location and can vary from about 10 m
to about 150 m. There should be a “free line of sight” between transmitting and receiving
antennas.
• To avoid overloading the receiver, observe a minimum distance of 5 m between
transmitting and receiving antennas.
... for multi-channel operation
• Each of the frequency banks “1” to “20” accommodates factory-preset receiving
frequencies which are intermodulation-free. For possible frequency combinations, please
refer to the supplied frequency information sheet.
• The channels in the frequency banks “U1” to “U6” can be assigned freely selectable
frequencies (see page 31).
• When using several transmitters simultaneously, interference can be avoided by
maintaining a minimum distance of 20 cm between two transmitters.
• Use accessories recommended by Sennheiser for multi-channel applications (see
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Accessories
Cat. No.
Accessory
004368 GA 3030 AM antenna front mount kit
502048 AC 3200 antenna combiner
500887 A 5000 CP circularly polarized broadband antenna
003658 A 2003 directional broadband antenna
004645 A 1031 omni-directional broadband antenna
087969 Antenna daisy-chain cable, 50 Ω, BNC, 0.25 m
002324 GZL 1019-A1 coaxial cable, type RG 58, BNC to BNC, 1 mm
34
Download from Www.Somanuals.com. All Manuals Search And Download.
If a problem occurs ...
If a problem occurs ...
Problem
Possible cause
Possible solution
Transmitter cannot be
operated, “Locked” appears on
the display panel
Lock mode is activated
Deactivate the lock mode (see page 14).
No operation indication
No mains connection
Check the connections of the mains cable.
No RF signal at the receiver
Transmitter and receiver are not
on the same channel
Synchronize the transmitter with the receiver
on the transmitter display:
RF signal is deactivated
Very weak RF signal at the
receiver
Transmission range is exceeded
Reduce the distance between receiver and
transmitter.
Reposition the antennas.
Increase the transmission power (see page 19).
Reduce the squelch threshold (see the
instruction manual of the receiver).
RF signal available,
no audio signal at the receiver
No input signal at the transmitter Check the audio level on the transmitter display
Very low input signal
Check the audio level on the transmitter display
signal or adjust the input sensitivity (see
Audio signal has a high level of Transmitter sensitivity is adjusted Adjust the transmitter sensitivity correctly
background noise
too low
Audio signal is distorted
If “AF PEAK” additionally appears Adjust the transmitter sensitivity correctly
on the transmitter display:
transmitter sensitivity is adjusted
too high
Receiver’s audio output level is
adjusted too high
Reduce the audio output level of the receiver.
If a problem occurs that is not listed in the above table or if the problem cannot be solved with the proposed solutions,
please contact your local Sennheiser partner for assistance.
To find a Sennheiser partner in your country, search at www.sennheiser.com under “Service & Support”.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
RF characteristics
Frequency ranges
516–558, 558–626, 626–698, 718–790, 790–865 MHz
(Aw to Dw, Gw, see page 4)
Transmission frequencies
up to 3,000 frequencies, tuneable in steps of 25 kHz
20 frequency banks, each with up to 32 factory-preset channels
6 frequency banks, each with up to 32 user programmable
channels
Switching bandwidth
Frequency stability
Antenna output
up to 75 MHz
10 ppm (–10 °C to +55 °C)
BNC socket, 50 Ω
RF output power at 50 Ω
typ. 10/30/50 mW (Low/Standard/High), switchable
AF characteristics
Modulation
wideband FM stereo (MPX pilot tone)
Sennheiser HDX
Compander system
Nominal/peak deviation
MPX pilot tone (frequency/deviation)
AF frequency response
24 kHz/ 48 kHz
19 kHz/ 5 kHz
25 Hz to 15 kHz
AF input BAL AF IN L (I)/BAL AF IN R (II)
2 x XLR-3/¼’’ (6.3 mm) jack combo socket,
electronically balanced
Max. input level
+22 dBu
< 0.9 %
> 90 dB
THD (at 1 kHz and nominal deviation)
Signal-to-noise ratio
at nominal load and peak deviation
AF output LOOP OUT BAL L (I)/LOOP OUT BAL R (II)
¼’’ (6.3 mm) stereo jack socket, balanced
Overall device
Temperature range
Power supply
–10 °C to + 55 °C
100–240 V~
Current consumption
SR 2000: 0.1 A
SR 2050: 0.2 A
Dimensions
Weight
approx. 217 x 483 x 43 mm
SR 2000: approx. 2500 g
SR 2050: approx. 2700 g
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
In compliance with
Europe
EMC
EN 301489-1/-9
Radio
Safety
EN 300422-1/-2, EN 300454-1/-2
EN 60065
Approved by
Canada
Industry Canada RSS 123
IC: 2099A-SR2000 and IC: 2099A-SR2050
limited to 806 MHz
USA
FCC-Part 74
FCC-ID: DMOSR2000 and DMOSR2050
limited to 698 MHz
Connector assignment
Audio
¼’’ (6.3 mm) stereo jack plug, balanced
XLR-3F connector, balanced (BAL AF IN)
(
BAL AF IN/LOOP OUT)
2
1
+
3
¼’’ (6.3 mm) mono jack plug, unbalanced
BAL AF IN/LOOP OUT)
¼’’ (6.3 mm) stereo jack plug for
headphone output
(
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer Declarations
Manufacturer Declarations
Warranty
Sennheiser electronic GmbH & Co. KG gives a warranty of 24 months on this product.
For the current warranty conditions, please visit our website at www.sennheiser.com or
contact your Sennheiser partner.
In compliance with the following requirements
• RoHS Directive (2002/95/EC)
• WEEE Directive (2002/96/EC)
Please dispose of the transmitter at the end of its operational lifetime by taking it to
your local collection point or recycling center for such equipment.
CE Declaration of Conformity
•
0682
• R&TTE Directive (1999/5/EC), Low Voltage Directive (2006/95/EC)
The declarations are available at www.sennheiser.com.
Before putting the device into operation, please observe the respective country-specific
regulations.
Statements regarding FCC and Industry Canada
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This class B digital device complies with the Canadian ICES-003.
Changes or modifications made to this equipment not expressly approved by Sennheiser
electronic Corp. may void the FCC authorization to operate this equipment.
Before putting the device into operation, please observe the respective country-specific
regulations!
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index
A
overview
PEAK (overmodulation)
activating/deactivating
AF Peak (warning message) 28
lock mode (Auto Lock) 25
RF Mute (warning message) 28
warning messages (Warnings) 28
transmission icon
transmission power
E
adjusting
equalizer
display of equalizer setting
input sensitivity (Sensitivity) 22
network configuration (IP Address) 29
receiver parameters (Sync Settings) 27
transmission power (RF Power) 28
extended menu (Advanced Menu)
overview 19
F
Advanced Menu (extended menu)
overview 19
settings 25
factory default settings (resetting the settings made in
frequency
antenna
connecting a remote antenna
connecting the AC 3200 antenna combiner
important notes on frequency selection 30
preset frequencies
connecting the rod antenna to the rear
mounting the rod antenna to the front
selecting ~ presets 23
setting a transmission frequency 25
antenna front mount kit
frequency bank
audio signal
daisy chaining 11
~ system
display
overview
selecting (Easy Setup) 30
selecting (Frequency Preset) 23
C
Frequency Preset (selecting a frequency bank/
channel
assigning a frequency 26
display
overview
selecting (Easy Setup) 30
selecting (Frequency Preset) 23
selecting (Tune) 25
I
L
connecting
lock mode
mains cable 12
mixing console 11
activating/deactivating (Auto Lock) 25
M
remote antenna
main menu (Menu)
overview 19
transmitters in a network 12
D
displays
adjusting the contrast of the display panel (LCD
Menu (main menu)
overview 19
AF (audio level)
AF PEAK (overmodulation)
frequency
input sensitivity
modulation (input sensitivity/adjusting the
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
transmitter
cleaning 32
fitting the device feet
mounting into a 19" rack
setting up on a flat surface
N
O
troubleshooting 35
operating menu
overview 18
using 20
R
Tune (setting the transmission frequencies and
U
using
Reset (resetting the settings made in the operating
equalizer 24
W
menu) 28
RF signal
activating 13
Warnings (warning messages)
activating/deactivating 28
overview 19
S
selecting
Software Revision (displaying the software
revision) 29
standby 14
Sync Settings (adjusting transferable receiver
settings) 27
T
transmission frequency
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|