Wireless Indoor Color
Hidden Teddy Cam
UC1301
Instruction
Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The SVAT UC1301 Wireless Indoor Color Hidden Teddy Cam allows you to
discretely keep an eye on your children. The Teddy Cam is very easy to
install, the transmitter is discretely hidden, and you don’t have to worry
about messy wiring through your infant’s room. This smart and cuddly bear
is the perfect solution for affordable baby monitoring.
MAIN FEATURES:
•High Resolution Color CMOS Camera
•High Performance Audio/Video Receiver
Bear Video Cam
•Operating frequency of 2.4GHz
•Four selectable channels
•Range of up to 300ft (Works best at 100ft)
Receiver
Power Adapter
WHAT’S INCLUDED
• 1 Teddy Cam
• 1Receiver
A/V Plug to RCA
Audio/Video Cable
• 1 RCA Wire
A/V Plug to RCA
• 2 AC Power Adapters (DC 9V)
• Mounting Hardware
• 1 Year Warranty
• Online/Toll Free Tech Support
RECEIVER
1. Power Switch
2. Channel Selector
3. AV Connector
4. Adapter Connector
5. LED Power Indicator
TEDDY CAM
1. Hidden Camera
BATTERY ROOM & SW BOARD
1. Channel Switch
2. Power Switch
3. Power Adapter Jack
4. 9V Battery Connector
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
TEDDY CAM
1. The Teddy Cam can be powered by either a 9 volt battery or with the
included AC Adapter.
2. Move the Teddy Cam to the desired location.
NOTE: The transmission range of the Teddy Cam is up to 150ft. Real
distance depends on its operating environment. If you are receiving
interference, try shortening the transmission range. Reposition and/or
adjust the Teddy Cam if video transmission is being degraded by
obstructions in its operating environment.
3. Select the desired transmission channel for the Teddy Cam.
NOTE: The Teddy Cam has four different transmission channels. Do not
use more than one video camera on the same channel. Doing so will
result in interference and an unclear picture.
•The transmitter is located inside the back of the bear. Unzip the
zipper and pull out the transmitter. Set the switch to the desired
channel (1-4)
5. Place a 9V battery into the battery compartment. Use only alkaline
batteries for the Teddy Cam. The Teddy Cam can also be powered
using the the AC Power Adapter. Plug it into the adapter jack, then
plug the AC Power Adapter into a standard 120V/230VAC electrical
outlet.
NOTE: Make sure to take the battery out of the battery compartment
before plugging in the AC Power Adapter.
7. Slide the Power ON/OFF Switch to the ON position.
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION Cont’d...
RECEIVER
1. Insert the AV Adapter Plug into the AV Output port of the receiver
2. Insert the yellow and white cable plugs into the Video Input and
Audio Input Jacks of your TV.
Receiver
TV
Audio Video
Input
Input
3.5 Plug
White Plug
Yellow Plug
AV Cable
Bear Video Camera
3. Connect the AC Power Adapter to the 9V Power Input Jack
of the receiver.
4. Select the desire channel (1-4). Make sure it matches the transmission
channel of the Teddy Cam.
5. Plug the AC Power Adaptor into a standard 120V/230V AC electrical
outlet.
6. Slide the ON/OFF Switch to the ON position.
7. Television Set configuration:
•Turn on the power to the television set.
•Switch the TV channel to the VIDEO/LINE INPUT position.
•Adjust the TV volume and pictures, as desired.
•TV/Video can be switched each other to monitor surroundings
while TV / DVD program is being played.
8. Unplug the AC Power Adaptor from the electrical outlet when it is not
in use or is left unattended.
VIDEO RECORDING SETUP
1. Follow the normal setup procedures for the Bear Video Camera and
Receiver.
2. Insert the yellow & white cable plugs into the Video Input and Audio
Input Jacks of your VCR/DVR.
3. Make sure your VCR is connected to your television set.
TV
A/V Source
Receiver
Audio Video
Input
Input
3.5 Plug
Yellow Plug
White Plug
AV Cable
Bear Video Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Please read this user’s manual carefully before using. If you still have diffi-
culties to use the product, consult the following
syndrome, which will help you solve most common problems.
No picture after turning on the TV
1. Check the power supply.
•Ensure that both the transmitter and receiver are properly connected
and set to the same channels.
•Ensure both the transmitter and receiver power indicators illuminate.
2. Ensure the video cable is well connected.
3. Ensure the TV channel is set to "Video".
4. Set the transmitter and receiver to the channel with the clearest signal.
5. Shorten the transmission range/distance between the transmitter and
receiver. Reposition and/or adjust the Teddy Cam.
Unclear picture reception
1. Ensure that both the transmitter and receiver are properly connected
and set to the same channels.
2. Shorten the transmission range/distance between the transmitter and
receiver. Reposition and/or adjust the Teddy Cam. Replace 9V battery
when necessary.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Wireless Camera -- CMOS
MODEL
DESCRIPTION
Scanning System
2:1 Interlace
NTSC
1/3" CMOS Image Sensor
Image Sensor
510 (H) X 492 (V) 628 (H) X 582 (V)
15750 Hz 15625 Hz
60 Hz 50 Hz
Efficiency Pixels
Horizontal Scan Frequency
Vertical Scan Frequency
Synchronize
Internal
Resolution
More than 300 TV Lines
3 LUX (F1.2)
Min. Illumination
S/N Ratio
More than 45 dB (AGC OFF)
1.0 Vpp / 75 ohm composite Video Signal
Video Input
1/60 ~ 1/2000 seconds
Auto Electronic Exposure
Auto White Balance
Supply Voltage
Power Consumption
Operation Environment
Lens
Auto
9V
120 mA
0 C ~ +40 C
F3.6mm, F2.0 (Fix Board Lens)
620g
Weight
RECEIVER
MODEL
Frequency
Receiver Sensitivity
Channel Number
L.O. Stability
DESCRIPTION
2400MHz ~ 2483 MHz
-90dBm (min.)
4
+/- 100 K
(Typ.)
Video Output Level
Supply Voltage
Power Consumption
Antenna
1Vpp / 75 ohm
9V
200 mA (Typ.)
Embedded
Operation Environment
Dimension(mm)
0 C ~ +40 C
83W x 70H x 42L
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY
We take quality very seriously. This is why all of our products
come with a one year warranty from the original purchase date
against defects in workmanship and materials.
If you have warranty or support issues please contact us using any of the following methods:
SVAT Electronics USA
2315 Whirlpool St., Unit 333
NIagara Falls, New York
USA 14305
SVAT Electronics Canada
4080 Montrose Road
Niagara Falls, ON
Phone: 866.946.7828
Fax: 888.771.1701
Email: [email protected]
Canada L2H 1J9
Warranty Terms
1. SVAT products are guaranteed for a period of one year from the date of purchase against defects in
workmanship and materials. This warranty is limited to the repair, replacement or refund of the purchase price
at SVAT's option.
2. When service is required, the warranty is validated by the submission of a fully completed warranty card.
3. This warranty becomes void if the product shows evidence of having been misused, mishandled or tampered
with contrary to the applicable instruction manual.
4. Routine cleaning, normal cosmetic and mechanical wear and tear are not covered under the terms of this
warranty.
5. The warranty expressly provided for herein is the sole warranty provided in connection with the product itself
and no other warranty, expressed or implied is provided. SVAT assumes no responsibilities for any other
claims not specifically mentioned in this warranty.
6. This warranty does not cover the shipping cost, insurance or any other incidental charges.
7. You MUST call SVAT before sending any product back for repair. You will be given a Return Authorization
number. When returning the product for warranty service, please pack it carefully in the original box with all
supplied accessories, and enclose your original receipt or copy, and a brief explanation of the problem
(include RA #).
8. This warranty is valid only in Canada and the U.S.A.
9. This warranty card cannot be re-issued.
CAUTION
RISK OF ELECTRIC SHOCK, DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Graphic Symbol Explanation:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operating maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE
Disclaimer: SVAT does not endorse of any of SVAT products for any illegal activites.
SVAT is not responsible or liable in any way shape or form for any damage, vandalism,
theft or any other action that may occur while a SVAT product is in use by the purchaser.
Important Information Required By The FCC
Warning : Changes or modifications to this unit not expressly approved by the party responsible for com-
pliance could void the user authority to operate the equipment. This device complies with Part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference thatmay
cause undesired operation.The user manual or instruction manual for an intentional or unintentional radi-
ator shall caution the user that changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user's authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
w w w . s v a t . c o m
If you require more information on this product
or other SVAT products visit
__________________________________________________________________________________________________________________
FCC STATEMENT:
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions,may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC LABEL COMPLIANCE STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
IC STATEMENT:
This equipment has been tested and found to comply with IC RSS 210 Standards.
_________________________________________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
|