C2SBA+II
C2SBA+
C2SBA
C2SBE
USER’S MANUAL
Revision 1.1c
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
About This Manual
This manual is written for system integrators, PC technicians and
knowledgeable PC users. It provides information for the installation and use of the
C2SBA+II/C2SBA+/C2SBA/C2SBE motherboard. The C2SBA+II/C2SBA+/
C2SBA/C2SBE supports single Intel Xeon 3000 Series/Core 2 Quad/Core 2 Duo
Processor with a system bus speed of up to 1.33 GHz. The Intel Core 2 Quad/Core 2
Duo Processor supports the 775-Land Grid Array Package, which interfaces with the
motherboard via an LGA775 socket. With the support of the Quad-Core/Dual-Core
Technology, Wide Dynamic Execution, FSB Dynamic Bus Inversion (DBI), Advanced
Digital Media Boost, Smart Memory Access, and Thermal Management 2 (TM2), the
C2SBA+II/C2SBA+/C2SBA/C2SBE delivers unparalleled system performance and
great power efficiency in a slim package. Please refer to the motherboard specifica-
tions pages on our web site (http://www.supermicro.com/Products/) for updates on
supported processors. This product is intended to be professionally installed and
serviced by a technician.
Manual Organization
Chapter 1 describes the features, specifications and performance of the mainboard
and provides detailed information about the chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when
installing the processor, memory modules and other hardware components into
the system.
If you encounter any problems, see Chapter 3, which describes troubleshooting
procedures for the video, the memory and the system setup stored in the CMOS.
Chapter 4 includes an introduction to BIOS and provides detailed information on
running the CMOS Setup utility.
Appendix A provides BIOS POST Messages.
Appendix B lists BIOS POST Codes.
Appendix C, Appendix D and Appendix E list HostRAID Setup Guidelines and
Other Software Installation Instructions.
Conventions Used in the Manual:
Special attention should be given to the following symbols for proper installation and
to prevent damage done to the components or injury to yourself:
Danger/Caution: Instructions to be strictly followed to prevent catastrophic
system failure or to avoid bodily injury.
Warning: Important information given to ensure proper system installation or
to prevent damage to the components.
Note: Additional Information given to differentiate various models or to ensure cor-
rect system setup.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Table of Contents
About This Manual ...................................................................................................... iii
Manual Organization ....................................................................................................iii
Conventions Used in the Manual..................................................................................iii
Chapter 1: Introduction
1-1 Overview ......................................................................................................... 1-1
Checklist ..................................................................................................... 1-1
Contacting Super Micro.............................................................................. 1-2
C2SBA+II/C2SBA+/C2SBA/C2SBE Image ............................... 1-3
C2SBA+II/C2SBA+/C2SBA/C2SBE Layout................................ 1-4
C2SBA+II/C2SBA+/C2SBA/C2SBE Quick Reference................. 1-5
Motherboard Features .............................................................................. 1-7
Intel G33/P35 Chipset: System Block Diagram ......................................... 1-9
1-2 Chipset Overview ......................................................................................... 1-10
1-3 Recovery from AC Power Loss .................................................................... 1-11
1-4 PC Health Monitoring ................................................................................... 1-11
1-5 ACPI Features .................................................................................................1-11
1-6 Power Supply ............................................................................................... 1-12
1-7 Versatile Media Capabilities ........................................................................... 1-13
1-8 Super I/O ...................................................................................................... 1-13
Chapter 2: Installation
2-1 Static-Sensitive Devices ................................................................................. 2-1
2-2 Motherboard Installation .................................................................................. 2-1
2-3 Processor and Heatsink Installation ............................................................... 2-2
2-4 Installing DDR2 Memory ................................................................................ 2-6
2-5 Control Panel Connectors/IO Ports................................................................. 2-8
Back Panel Connectors/IO Ports...................................................................... 2-8
Front Control Panel .......................................................................................... 2-9
Front Control Panel Pin Definitions................................................................ 2-10
PWR LED ............................................................................................... 2-10
HDD LED................................................................................................. 2-10
NIC1 LED Indicators .............................................................................. 2-11
OH/Fan Fail LED ......................................................................................2-11
Reset Button............................................................................................ 2-12
PWR Button............................................................................................. 2-12
2-6 Connecting Cables ....................................................................................... 2-13
ATX/Auxiliary Power Connectors ........................................................... 2-13
Universal Serial Bus (USB)..................................................................... 2-14
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chassis Intrusion .................................................................................... 2-14
Fan Headers............................................................................................. 2-15
VGA Connector ........................................................................................ 2-15
ATX PS/2 Keyboard and PS/2 Mouse Ports............................................ 2-16
Serial Ports............................................................................................... 2-16
Wake-On-Ring ......................................................................................... 2-17
Wake-On-LAN .......................................................................................... 2-17
GLAN1 Port.............................................................................................. 2-18
Speaker Connector .................................................................................. 2-18
High Definition Audio (HDA)..................................................................... 2-19
CD Header/Auxiliary Audio Header.......................................................... 2-19
Front Panel Audio Control........................................................................ 2-20
Power LED ............................................................................................... 2-20
2-7 Jumper Settings ............................................................................................ 2-21
Explanation of Jumpers ......................................................................... 2-21
GLAN Enable/Disable .............................................................................. 2-21
CMOS Clear ........................................................................................... 2-22
Watch Dog Enable ................................................................................... 2-22
PCI/PCI-Exp. Slots to SMB Speeds......................................................... 2-23
Keyboard Wake-Up .................................................................................. 2-23
IDE Enable/Disable .................................................................................. 2-24
TPM Enable.............................................................................................. 2-24
Audio Enable............................................................................................ 2-25
USB Wake-Up .......................................................................................... 2-26
2-8 Onboard Indicators ....................................................................................... 2-27
GLAN LED Indicators............................................................................... 2-27
Onboard Power LED................................................................................ 2-28
2-9 Parallel Port, Floppy Drive and IDE Hard Drive Connections ..................... 2-29
Parallel Port Connector............................................................................ 2-29
Floppy Connector.................................................................................... 2-30
IDE Connectors........................................................................................ 2-31
Chapter 3: Troubleshooting
3-1 Troubleshooting Procedures ........................................................................... 3-1
Before Power On....................................................................................... 3-1
No Power................................................................................................... 3-1
No Video .................................................................................................. 3-1
Memory Errors........................................................................................... 3-2
Losing the System’s Setup Configuration ................................................ 3-2
v
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
3-2 Technical Support Procedures ........................................................................ 3-2
3-3 Frequently Asked Questions ........................................................................... 3-3
3-4 Returning Merchandise for Service................................................................. 3-5
Chapter 4: BIOS
4-1 Introduction ....................................................................................................... 4-1
4-2 Running Setup ................................................................................................. 4-2
4-3 Main BIOS Setup ............................................................................................. 4-3
4-4 Advanced Setup ............................................................................................... 4-7
4-5 Security Setup ............................................................................................... 4-22
4-6 TPM State....................................................................................................... 4-24
4-7 Boot Setup...................................................................................................... 4-25
4-8 Exit.................................................................................................................. 4-26
Appendices:
Appendix A: BIOS POST Messages .........................................................................A-1
Appendix B: BIOS POST Codes................................................................................B-1
Appendix C: Intel HostRAID Setup Guidelines..........................................................C-1
ApAppendix D: The Adaptec HostRAID Setup Guidelines ......................................D-1
Appendix E: Installing Other Software Programs and Drivers.................................E-1
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1
Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Super Micro boards are designed with the utmost attention
to detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
All the following items are included in the retail box only:
One (1) Super Micro Mainboard
One (1) floppy drive ribbon cable (CBL-022L)
Four (4) SATA cables (CBL-0044L) (For C2SBA+/C2SBA/C2SBE)
Six (6) SATA cables (CBL-0044L) (For the C2SBA+II only)
Two (2) IDE hard drive cables (CBL-0036L-3) (C2SBA+II/C2SBA+ Only)
One (1) Super Micro CD containing drivers and utilities
One (1) User's/BIOS Manual
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Contacting Super Micro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
+1 (408) 503-8000
Tel:
Fax:
Email:
+1 (408) 503-8008
[email protected] (General Information)
www.supermicro.com
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
+31 (0) 73-6400390
Tel:
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
Asia-Pacific
Address:
Super Micro, Taiwan
4F, No. 232-1 Liancheng Road
Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
+886-(2) 8226-3990
Tel:
Fax:
+886-(2) 8226-3991
Web Site:
www.supermicro.com.tw
Technical Support:
Email:
Tel:
886-2-8228-1366, ext.132 or 139
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
C2SBA+II/C2SBA+/C2SBA/C2SBE Image
Note: All pictures and drawings shown in this manual were based upon the latest
PCB revision available at the time of publishing of the manual. The motherboard
you've received may or may not look exactly the same as those in this manual.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Motherboard Layout
CPU Fan
J41
JKB
FAN2
4-Pin PWR
J28
Processor
J31
J30
JG1
J43
J40
Intel G33
J11
North Bridge
J46
Slot7 PCI-E x1
J27
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JI2C2
JPL1
JWOR
JP3
JWD
JLED
Intel ICH9
I-SATA2
Audio CTRL
I-SATA3
I-SATA0
Slot4 PCI-33MHz
South Bridge
JP5
Audio Enabled
I-SATA4
I-SATA5
JF1
I-SATA1
CD-IN
CD1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
Front-Access USB 12
Front-Access USB 11
JPUSB2
J10
J3
Slot1 PCI-33MHz
COM2
J13
IDE#2
Buzzer
SPKR1
IDE#1
WOL
(Please see important notes on Page 1-6.)
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
C2SBA+II/C2SBA+/C2SBA/C2SBE Quick Reference
Jumpers
JBT1
Description
Default Setting
(See Chapter 2)
CMOS Clear
JKB
Keyboard Enabled Pins 1-2 (Enabled)
2
2
JI C1/JI C2
JP2
SMB to PCI Slots Open/Open (Disabled)
ITE IDE Enabled Pins 1-2 (Enabled) (See Note 4)
JP3
TPM Enabled
Audio Enabled
Pins 1-2 (Enabled) (See Note 6)
Pins 1-2 (Enabled)
JP5
JPL1
Giga-bit LAN Enab. Pins 1-2 (Enabled)
B/P USB Wake Up Pins 2-3 (Disabled)
F/P USB Wake Up Pins 2-3 (Disabled)
Watch Dog Enable Pins 1-2 (Reset)
JPUSB1
JPUSB2
JWD
Connectors
Description
Audio
Audio Port (J46)
(FP) Audio
CD1
Front Panel Audio Connector (J12)
Audio CD Input (CD-In) Header
COM1/COM2
COM Port/Serial Port 1 & Port 2 Connectors (J31, J13)
DIMM#1A,#2A,#1B,#2B Memory (DIMM) Slots (1 through 4)
Fans 1-5
Floppy
Fan1: CPU Fan, Fan2-5: System/Chassis Fan Headers
Floppy Disk Connector (J27)
Front Control Panel
IDE#1/IDE#2
J9
Front Control Panel Header (JF1)
IDE Hard Drive #1 & Hard Drive #2 (See Note 4)
Speaker Header
J40
ATX 24-Pin Power Connector
J41
12V 4-pin Power Connector (Required connection)
Chassis Intrusion Header
JL1
JLED
Onboard Power LED Indicator
KB/Mouse
LE1
PS/2 Keyboard/Mouse (J28)
Standby Power LED Indicator
Parrallel
SATA 0/1/4/5
Slot 1-Slot 4
Slots 5-7
Parallel Printer Port (J30)
Intel SATA (#0/1/4/5) Headers (See Note 8)
PCI 33 MHz (PCI #1-#4) (See Note 5)
PCI-E x4 (Slot5), PCI-E x16 (Slot6), PCI-Ex1 (Slot7)
(BP) USB 1/2 & GLAN (Back Panel) Universal Serial Ports 1-2 & G-LAN Port
(BP) USB 3-6
(FP) USB 7/8, 9/10
(FP) USB 11, 12
VGA
(Back Panel) Universal Serial Ports 3-6 (J43)
(Front Panel) USB ports 7/8 (J44), USB 9/10 (J45)
Front-Accessible USB ports #11 (J47), USB #12 (J48)
Video/Graphics Connector (See Note 7)
Wake-On-LAN Header
WOL
WOR
Wake-On-Ring Header
(All notes indicated above are listed on Page 1-6.)
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Important Notes to the User
•
1. Jumpers not indicated are for testing only.
•
2. See Chapter 2 for detailed information on CPU/Heatsink installation, memory
population, jumpers, connectors, I/O ports and JF1 front panel connections.
•
•
•
•
3. " " indicates the location of "Pin 1.'
4. IDE is available on the C2SBA/C2SBA+/C2SBA+II only.
5. PCI Slot 4 is not available on the C2SBA+/C2SBA+II.
6. Trusted Platform Module (TPM) support is available on the C2SBA and
C2SBA+II/C2SBA+ only.
•
•
•
7. VGA is not available on the C2SBE.
8. The ICH9R and SATA Ports 2 & 3 (JS3/4) are available on the C2BA+II.
9. G33 is available on the C2SBA/C2SBA+II/C2SBA+. P35 is available on the
C2SBE only.
Overclocking Considerations
Warning: Please be aware of the following conditions when "overclock-
ing" is used:
Setting a high CPU FSB Speed (overclocking), DRAM Frequency or selecting a
high CPU V-Core voltage, memory voltage, chipset voltage, ICH chipset voltage,
or the FSB termination voltage may result in system instability. If this occurs, revert
the setting to the default setting. In addition, extra fans may be needed for proper
system cooling. The C2SBA+II/C2SBA+/C2SBA/C2SBE offers the option of "over-
clocking"; however, Super Micro is not responsible for any damage caused by the
use of overclocking.
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Motherboard Features
CPU
•
Single Intel Xeon 3000 Series/Core 2 Quad/Core 2 Duo Processor with a system
bus speed of 1.33 GHz/1.066 GHz
•
Supports Intel Dual Core Technology, Hyper-Threading, Wide Dynamic Execu-
tion, FSB Dynamic Bus Inversion (DBI), Advanced Digital Media Boost, Smart
Memory Access, and Thermal Management 2 (TM2)
Memory
•
Supports unbuffered single or dual channel Non ECC Unbuffered DDR2 up
to 8GB/s (DDR2 800/667) for single channel mode or dual-channel Interleaved
mode.
Chipset
•
Intel G33/P35 GMCH (North Bridge), ICH9/ICH9R (South Bridge)
Expansion Slots
•
•
•
•
One (1) PCI-Express x16 (Slot 6)
One (1) PCI-Express x4 (Slot 5)
One (1) PCI-Express x1 (Slot 7)
Four (4) 32-bit PCI 33MHz (Slot 1 to Slot 4) (Slot 4: Not available on the
C2SBA+II/C2SBA+)
BIOS
•
DMI 2.3, PCI 2.2, ACPI 1.0/2.0, SMBIOS 2.3, and Plug and Play (PnP)
PC Health Monitoring
•
Onboard voltage monitors for CPU Core Voltage, Memory Voltage,+1.8V, +3.3V,
+3.3V standby, +5V, Vbat (battery voltage) and ±12V
Fan status monitor with firmware 4 pin fan speed control
CPU 3-Phase-switching voltage regulator
•
•
•
•
•
•
•
•
•
•
SuperDoctor III, Watch Dog, NMI
Power-up mode control for recovery from AC power loss
CPU/System overheat LED and control
System resource alert via Supero Doctor III
Auto-switching voltage regulator for the CPU core
CPU Thermal Trip support
Thermal Monitor 2 (TM2) support
Trusted Platform Module (TPM) support
ACPI Features
•
•
•
•
Slow blinking LED for suspend state indicator
BIOS support for USB keyboard
Main switch override mechanism
External modem ring-on
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Onboard I/O
•
Built in ICH9 SATA Controller, 4 connectors for 4 devices (For the C2SBA+/
C2SBA/C2SBE)
•
•
•
•
•
•
Built in ICH9R SATA Controller, 6 connectors for 6 devices (For the C2SBA+II)
1 floppy port interface (up to 2.88 MB)
1 Fast UART 16550 compatible serial port/header
Intel 82566 Gigabit Ethernet Controller
PS/2 mouse and PS/2 keyboard ports
ITE-8212 IDE controller or ITE-8211 IDE controller (for PCB Rev. 1.2a and above)
supports two IDE hard drives (for the C2SBA+II/C2SBA+ only)
Up to 12 USB (Universal Serial Bus) 2.0 ports for a speed of up to 480Mbps
Realtek ALC 883 7.1 Channel High Definition Audio (HDA) codec supports 10
DAC Channels
•
•
•
Built-in GMCH and onboard VGA connector (Not available on C2SBE)
Other
•
Trusted Platform Module (TPM) 1.2 support (For the C2SBA/C2SBA+II/C2SBA+
only)
•
•
•
•
•
•
Wake-on-LAN
Wake-on-Ring (WOR)
System Bus Clock Frequency Selection (Overclocking) Support (Note)
Suspend-to-RAM
Onboard +3V Standby Power Warning LED ("LE1")
Pb Free
CD Utilities
•
•
BIOS flash upgrade utility
Drivers and software for Intel G33/P35 chipset utilities
Dimensions
• ATX form factor, 12.0" x 9.6" (304.8 x 243.8 mm)
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
VRM 11.0
LGA775_PROCESSOR
CK505 CLK
VRM 11.0
FSB: 1333/1066MHz
INTEGRATED
DIMM_CHA
DIMM_CHB
DDR2 800/667
GRAPHICS
G33/P35
GMCH/MCH
PCIE_x16
1 PCIE_x16
GRAPHIC
1_PCIE_x1
PCIE_x1
PCIE_x4
S-ATA/300
USB2.0/1.1
4 or 6 SATAII
PORTS
1_PCIE_x8
3_PCI_x32
ICH-9(R)
PCI_32
PCI_32
12x USB2.0
PORTS
1_PCI_x32
(Option)
SPI BIOS
PCIE_x1
ITE-8212
(Option)
82566 G_LAN
LPC
TPM
RJ45 PORT
IDE1
W83627DHG
LPC I/O
7.1-CH
HD_AUDIO
IDE2
HD_AUDIO
PORTS
KB. MS.
FDD.
SER.1/2
PRN.
The Intel G33/P35 Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your motherboard. See the following pages for the
actual specifications of each motherboard.
Note 1: Integrated Graphics support is not available for the P35 Chipset.
Note 2: ICH9R is available on the C2SBA+II only.
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
1-2
Chipset Overview
The Intel G33/P35 chipset is specially designed for use with the Intel dual core
processors. It consists of two primary components: the Graphic Memory Controller
Hub (GMCH) and the I/O Controller Hub (ICH9/ICH9R). The GMCH (North Bridge)
manages the data flow between the CPU interface (FSB), the System Memory
interface, the External Graphics interface, and the I/O Controller through the DMI
(Direct Media) Interface. The ICH9/ICH9R (South Bridge) provides a multitude of
I/O related functions.
Graphic Memory Controller Hub (GMCH)
Utilizing a single LGA 775 socket processor, the G33/P35 GMCH supports an FSB
frequency of 1.33 GHz/1.06 GHz. Host-initiated I/O cycles are decoded to the PCI-
Express, the DMI, or the GMCH configuration space. Host-initiated memory cycles
are decoded to PCI-Express, DMI or system memory. The GMCH supports 36-bit
host bus addressing and a Cache Line Size of 64 bytes.
The GMCH supports one or two channels of DDR2 memory with up to two DIMMs
per channel with a maximum bandwidth of 6.4 GB/s in asymmetric mode or 12.8
GB/s in symmetric mode using DDR2 800 MHz memory. It also supports an op-
portunistic refresh scheme, a memory thermal management scheme and Partial
Writes to Memory using Data Mask (DM) signals.
The GMCH contains one PCI-Express x16 (16-lane) port intended for an external
PCI-Express graphics card that is compatible with the PCI Express Base Specifica-
tion revision 1.1. This PCI-E x16 port runs at a frequency of 2.5 GB/s on each lane
and supports a maximum theoretical bandwidth of 40 GB/s in each direction for
an aggregate of 8 GB/s @ x16. It supports traditional PCI-/AGP- style traffic and a
PCI-Exp. Enhanced Addressing Mechanism with advanced capabilities in automatic
discovery, negotiation and training of link out of reset.
Providing the high-speed, chip-to-chip connection between the GMCH and ICH9/
ICH9R is the Direct Media Interface (DMI). The DMI integrates advanced priority-
based servicing, allowing for concurrent traffic, true isochronous transfer capabilities
and permitting current as well as legacy software to function seamlessly.
Intel ICH9/ICH9R System Features
The Intel 9th Generation I/O Controller Hub (ICH9/ICH9R) supports a variety of I/O
related functions and PCI devices, including the following:
•
•
•
•
•
DMI-to PCI Bridge
LPC Controller
Thermal Subsystem
SMBus Controller
USB FS/LS UHCI Controllers #1, #2 and #3
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-3
Recovery from AC Power Loss
BIOS provides a setting for you to determine how the system will respond when
AC power is lost and then restored to the system. You can choose for the system
to remain powered off (in which case you must hit the power switch to turn it back
on) or for it to automatically return to a power on state. See the Power Lost Con-
trol setting in the BIOS chapter of this manual to change this setting. The default
setting is Last State.
1-4
PC Health Monitoring
This section describes the PC health monitoring features of the C2SBA+II/C2SBA+/
C2SBA/C2SBE. The motherboard has an onboard System Hardware Monitor chip
that supports PC health monitoring.
Onboard Voltage Monitors for the CPU Core, +1.8V, +3.3V, +3.3V
standby, +5V, Vbat and ±12V
The onboard voltage monitor will scan these voltages continuously. Once a voltage
becomes unstable, it will give a warning or send an error message to the screen.
Users can adjust the voltage thresholds to define the sensitivity of the voltage moni-
tor by using SuperO Doctor III.
1-5
ACPI Features
ACPI stands for Advanced Configuration and Power Interface. The ACPI specifica-
tion defines a flexible and abstract hardware interface that provides a standard
to integrate power management features throughout a PC system, including its
hardware, operating system and application software. This enables the system to
automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers. This also includes consumer devices connected to the PC
such as VCRs, TVs, telephones and stereos.
In addition to enabling operating system-directed power management, ACPI pro-
vides a generic system event mechanism for Plug and Play and an operating- sys-
tem-independent interface for configuration control. ACPI leverages the Plug and
Play BIOS data structures while providing a processor architecture-independent
implementation that is compatible with Windows 2000, Windows XP, Windows 2003,
Windows 2003 Servers.
Enhanced Power Management
The onboard ICH9/ICH9R chip provides advanced power management functions
that will greatly improve the performance of various low-power (suspend) states and
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
enhance clock control. A hardware-based component provides software-indepen-
dent thermal management that is compatible with the ACPI Revision 3.0a.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start blinking
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.
BIOS Support for USB Keyboard
If the USB keyboard is the only keyboard in the system, it will function like a normal
keyboard during system boot-up.
Wake-On-LAN (WOL)
Wake-On-LAN is defined as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, up-dates and asset
tracking can occur after hours and on weekends so that daily LAN traffic is kept
to a minimum and users are not interrupted. The motherboard has a 3-pin header
(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has
WOL capability. In addition, an onboard LAN controller can also support WOL
without any connection to the WOL header. The 3-pin WOL header is to be used
with a LAN add-on card only.
Note: Wake-On-LAN requires an ATX 2.01 (or above) compliant power supply.
1-6
Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates of 1 GHz and faster.
The
C2SBA+II/C2SBA+/C2SBA/C2SBE accommodates 12V ATX power
supplies. Although most power supplies generally meet the specifications required
by the CPU, some are inadequate. A 2-Amp of current supply on a 5V Standby
rail is strongly recommended.
It is strongly recommended that you use a high quality power supply that meets
12V ATX power supply Specification 1.1 or above. It is also required that the 12V
4-pin power connection (J41) be used for high-load configurations. In areas where
noisy power transmission is present, you may choose to install a line filter to shield
the computer from noise. It is recommended that you also install a power surge
protector to help avoid problems caused by power surges.
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-7
Versatile Media Capabilities
High Definition Audio
The High Definition Audio Controller embedded in the ICH9/ICH9R delivers up to
4 codecs that can be used for different types of codecs, such as audio and mo-
dem codecs. Operating at 3.3V or 1.5V, the embedded Audio Controller supports
a multi-channel audio stream, 32-bit sample depth, up to 192 kHz of same rate,
and can be used with a variety of microphones for input. With these versatile audio
capabilities built in, the C2SBA+II/C2SBA+/C2SBA/C2SBE provides the user with
a surreal audio experience that is larger than life.
I/O Virtualization Technology (VT-d)
With the Intel ICH9 built in, the C2SBA+II/C2SBA+/C2SBA/C2SBE supports I/O
Virtualization Technology (VT-d) that enables multiple operating systems and ap-
plications to run in independent partitions. Each partition uses its own subset of host
physical memory, and behaves like a virtual machine (VM), providing isolation and
protection across multiple partitions. This feature is available when a processor that
supports the virtualization of platforms is installed on the motherboard.
1-8
Super I/O
The disk drive adapter functions of the Super I/O chip include a floppy disk drive
controller that is compatible with industry standard 82077/765, a data separator,
write pre-compensation circuitry, decode logic, data rate selection, a clock genera-
tor, drive interface control logic and interrupt and DMA logic. The wide range of
functions integrated onto the Super I/O greatly reduces the number of components
required for interfacing with floppy disk drives. The Super I/O supports two 360 K,
720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data transfer rates of 250 Kb/s,
500 Kb/s or 1 Mb/s.
It also provides two high-speed, 16550 compatible serial communication ports
(UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable baud
rate generator, complete modem control capability and a processor interrupt sys-
tem. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps as well
as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which support
higher speed modems.
The Super I/O provides functions that comply with the ACPI (Advanced Configura-
tion and Power Interface), which includes support of legacy and ACPI power man-
agement through a SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User’s Manual
Notes
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Chapter 2
Installation
2-1
Static-Sensitive Devices
Electro-Static-Discharge (ESD) can damage electronic components. To prevent
damage to your system board, it is important to handle it very carefully. The following
measures are generally sufficient to protect your equipment from ESD.
Precautions
•
•
Use a grounded wrist strap designed to prevent static discharge. Touch a
grounded metal object before removing the board from the antistatic bag.
Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the motherboard and peripherals back into their antistatic bags when not in
use.
•
•
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
Use only the correct type of onboard CMOS battery as specified by the manu-
facturer. Do not install the onboard battery upside down to avoid possible explo-
sion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.
2-2
Motherboard Installation
Note: Be sure to mount the motherboard into the chassis before you install the
CPU onto the motherboard.
All motherboards have standard mounting holes to fit different types of chassis.
Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Make sure that the metal standoffs click in or are screwed in tightly.
Then use a screwdriver to secure the motherboard onto the motherboard tray.
(Caution: 1. Please do not use a force greater than 8 lb/inch on each mounting
screw during motherboard installation. 2. Some components are very close to the
mounting holes. Please take precautionary measures to prevent damage to these
components when installing the motherboard to the chassis.)
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
2-3 Processor and Heatsink Fan Installation
When handling the processor package, avoid placing
!
direct pressure on the label area of the fan.
Notes: 1. Always connect the power cord last and always remove it before adding,
removing or changing any hardware components. Make sure that you install the
processor into the CPU LGA 775 socket before you install the CPU heatsink.
2. The Intel LGA 775 Processor package contains the CPU fan and heatsink as-
sembly. If you buy a CPU separately, make sure that you use only Intel-certified
multi-directional heatsink and fan.
3. Make sure to install the motherboard into the chassis before you install the CPU
heatsink and fan.
4. When purchasing an LGA 775 Processor or when receiving a motherboard with
an LGA 775 Processor pre-installed, make sure that the CPU plastic cap is in place
and none of the CPU pins are bent; otherwise, contact the retailer immediately.
5. Refer to the MB Features Section for more details on CPU support.
Installation of the LGA 775 Processor
Load Lever
PnP Cap on
top of the
Load Plate
1. Press the load lever to release
the load plate, which covers the CPU
socket, from its locking position.
2. Gently lift the load lever to open the
load plate.
Load Plate
(with PnP Cap
attached)
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
North Center Edge
3. Use your thumb and your index
finger to hold the CPU at the North
Center Edge and the South Center
Edge of the CPU.
4. Align CPU Pin1 (the CPU corner
marked with a triangle) against the
socket corner that is marked with a
triangle cutout.
South Center Edge
golden dot
5. Align the CPU key that is the
semi-circle cutout below a golden dot
against the socket key, the Notch on
the same side of the triangle cutout
on the socket.
Socket Key
(Socket Notch)
CPU Key (semi-
circle cutout)
below the circle.
6. Once aligned, carefully lower the
CPU straight down to the socket.
(Note: Do not drop the CPU on the
socket. Do not move the CPU horizon-
tally or vertically. Do not rub the CPU
against the surface or against any pins
of the socket to avoid damage to the
CPU or the socket.)
Corner with a
triangle cutout
CPU Pin1
7. With the CPU inside the socket,
inspect the four corners of the CPU
to make sure that the CPU is properly
installed.
Load Lever
8. Use your thumb to gently push the
load lever down to the lever lock.
CPU in the CPU socket
9. If the CPU is properly installed into
the socket, the plastic PnP cap will be
automatically released from the load
plate when the load lever is pushed
in the lever lock. Remove the PnP cap
from the motherboard.
(Warning: Please save the plas-
!
Plastic cap
is released
from the
load plate
if CPU
tic PnP cap. The motherboard must
be shipped with the PnP cap properly
installed to protect the CPU socket
pins. Shipment without the PnP cap
properly installed will cause damage
to the socket pins.)
properly
installed.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Installation of the Heatsink
1. Locate the CPU Fan on the mother-
board. (Refer to the layout on the right
for the CPU Fan location.)
2. Position the heatsink in such a way
that the heatsink fan wires are closest
to the CPU fan and are not interfered
with other components.
3. Inspect the CPU Fan wires to make
sure that the wires are routed through
the bottom of the heatsink.
4. Remove the thin layer of the protec-
tive film from the copper core of the
Thermal Grease
heatsink.
(Warning: CPU overheat may occur if
the protective film is not removed from
the heatsink.)
CPU
5. Apply the proper amount of thermal
grease on the CPU. (Note: if your
heatsink came with a thermal pad,
please ignore this step.)
Fan Wires
Heatsink Fins
6. If necessary, rearrange the wires
to make sure that the wires are not
pinched between the heatsink and the
CPU. Also make sure to keep clear-
ance between the fan wires and the
fins of the heatsink.
Heatsink
Fastener
7. Align the four heatsink fasteners
with the mounting holes on the mother-
board. Gently push the pairs of diago-
nal fasteners (#1 & #2, and #3 & #4)
into the mounting holes until you hear
a click. (Note: Make sure to orient each
fastener in a way that the narrow end of
the groove is pointing outward.)
#1
#4
#3
#2
Narrow end of the groove
points outward
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
8. Repeat Step 6 to insert all four heatsink
fasteners into the mounting holes.
9. Once all four fasteners are securely insert-
ed into the mounting holes and the heatsink
is properly installed on the motherboard,
connect the heatsink fan wires to the CPU
Fan connector.
Heatsink Removal
1. Unplug the power cord from the power
supply.
2. Disconnect the heatsink fan wires from the
CPU fan header.
3. Use your finger tips to gently press on the
fastener cap and turn it counterclockwise
to make a 1/4 (900) turn, and then pull the
fastener upward to loosen it.
4. Repeat Step 3 to loosen all fasteners from
the mounting holes.
5. With all fasteners loosened, remove the
heatsink from the CPU.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
2-4 Installing DIMMs
Note: Check the Super Micro web site for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage. Also note that the
memory is interleaved to improve performance (See step 1).
DIMM Installation
1. Insert the desired number of DIMMs into the memory slots, starting with DIMM1A.
The memory scheme is interleaved so you must install two modules at a time,
beginning with DIMM1A, DIMM1B, then, DIMM2A and DIMM2B
2. Insert each DIMM module vertically into its slot. Pay attention to the notch along
the bottom of the module to prevent inserting the DIMM module incorrectly.
3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules (See step 1 above).
Memory Support
The C2SBA+II/C2SBA+/C2SBA/C2SBE supports up to 8 GB Unbuffered Non-
ECC DDR2 800/677 MHz in 4 DIMMs. Populating DIMM#1A,DIMM#1B, and/or
DIMM#2A, DIMM#2B with memory modules of the same size and of the same
type will result in dual channel, two-way interleaved memory which is faster than
the single channel, non-interleaved memory.
Notes:
1. Due to the OS limitations, some operating systems may not show more than 4
GB of memory.
2. Both Unbuffered ECC and Non-ECC memory modules can be installed in the
memory slots. However, the functionality of ECC is not supported by the
chipset.
3. Due to memory allocation to system devices, memory remaining available for
operational use will be reduced when 4 GB of RAM is used. The reduction
in memory availability is disproportional. (Refer to the following Memory
Availability Table for details.) For Microsoft Windows users: Microsoft imple-
mented a design change in Windows XP with Service Pack 2 (SP2) and
Windows Vista. This change is specific to the Physical Address Extension
(PAE) mode behavior which improves driver compatibility. For more informa-
tion, please read the following article at Microsoft’s Knowledge Base website
at: http://support.microsoft.com/kb/888137.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory
Remaining (-Available)
(4 GB Total System Memory)
Firmware Hub flash memory (System 1 MB
3.99
BIOS)
Local APIC
4 KB
3.99
3.99
3.99
3.76
3.51
3.01
Area Reserved for the chipset
I/O APIC (4 Kbytes)
PCI Enumeration Area 1
PCI Express (256 MB)
2 MB
4 KB
256 MB
256 MB
PCI Enumeration Area 2 (if needed) 512 MB
-Aligned on 256-MB boundary-
VGA Memory
TSEG
16 MB
1 MB
2.85
2.84
2.84
Memory available to OS and other ap-
plications
Installing and Removing DIMMs
DIMM2
Notch
Notch
Release
Tab
Release
Tab
Note: Notch
should align
with the
receptive point
on the slot
To Install: Insert module vertically and press down until it
snaps into place. Pay attention to the alignment notch at
the bottom.
To Remove:
Top View of DDR2 Slot
Use your thumbs
to gently push
the release tabs
near both ends of
the module. This
should release it
from the slot.
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
2-5 Control Panel Connectors/IO Ports
The I/O ports are color coded in conformance with the PC 99 specification. See the
graphics below for the colors and locations of the various I/O ports.
Back Panel Connectors/IO Ports
8
17
14
4
2
1
7
11
16
15
10
9
18
13
12
3
6
5
Back Panel I/O Port Locations and Definitions
Back Panel Connectors
1. Keyboard (Purple)
2. PS/2 Mouse (Green)
3. COM Port 1 (Turquoise)
4. Parallel Port (Printer)
5. Back Panel USB Port 3
6. Back Panel USB Port4
7. Back Panel USB Port 5
8. Back Panel USB Port 6
9. Back Panel USB Port 1
10. Back Panel USB Port 2
11. Gigabit LAN 1
12. Side_Surround (Grey)
13. Back_Surround (Black)
14. CEN/LFE (Orange)
15. Microphone-In (Pink)
16. Front (Green)
17. Line-In (Blue)
18. VGA (Not included on the
C2SBE)
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally lo-
cated on a control panel at the front of the chassis. These connectors are designed
specifically for use with Super Micro server chassis. See the pictures below for the
descriptions of the various control panel buttons and LED indicators. Refer to the
following section for descriptions and pin definitions.
JF1 Header Pins
LED_Anode+
LED_Anode+
LED_Anode+
Power LED
HDD LED
NIC1 LED
X
X
OH/Fan Fail LED
LED_Anode+
X
X
Reset
PWR
Reset Button
Power Button
Ground
Ground
2
1
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Front Control Panel Pin Definitions
Power LED
Power LED
Pin Definitions
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
Pin# Definition
15
16
LED_Anode+
PWR LED Signal
HDD LED
HDD LED
Pin Definitions
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
hard drive LED cable here to display
disk activity (for any hard drives on
the system, including SAS and Serial
ATA). See the table on the right for
pin definitions.
Pin# Definition
13
14
LED_Anode+
HD Active
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. PWR LED
B. HDD LED
LED_Anode+
LED_Anode+
LED_Anode+
Power LED
HDD LED
NIC1 LED
Intel G33
A
B
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
X
X
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
OH/Fan Fail LED
LED_Anode+
X
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
X
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
Reset
PWR
Reset Button
FP USB 7/8
FP USB 9/10
Ground
Ground
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Power Button
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
2
1
IDE#1
WOL
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
NIC1 Indicator
GLAN1/2 LED
Pin Definitions
The NIC (Network Interface Control-
ler) LED connection for the GLAN port
is located on pins 11 and 12 of JF1.
Attach the NIC LED cables to display
network activity. Refer to the table on
the right for pin definitions.
Pin# Definition
11
12
LED_Anode+
NIC1 LED
Signal
OH/Fan Fail LED
Pin Definitions
Overheat/Fan Fail LED (OH)
Pin# Definition
Connect an LED to the OH/Fan Fail
connection on pins 7 and 8 of JF1 to
provide advanced warnings of chassis
overheating or fan failure. Refer to the
table on the right for pin definitions.
7
8
LED_Anode+
OH/Fan Fail
LED Signal
OH/Fan Fail Indicator
Status
State Definition
Off
On
Normal
Overheat
Fan Fail
Flash-
ing
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. NIC1 LED
B.OH/Fan Fail LED
LED_Anode+
Power LED
Intel G33
LED_Anode+
LED_Anode+
HDD LED
NIC1 LED
North Bridge
A
Slot7 PCI-E x1
Slot6 PCI-E x16
X
X
GLAN CTRL
Slot5 PCI-E x4
JBT1
OH/Fan Fail LED
LED_Anode+
X
Battery
JI2C1
JPL1
JI2C2
JWOR
B
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
X
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
Reset
PWR
Reset Button
LE1
Ground
Ground
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Power Button
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
2
1
IDE#1
WOL
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Reset Button
Reset Button
Pin Definitions
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a
hardware reset switch on the computer
case. Refer to the table on the right for
pin definitions.
Pin# Definition
3
4
Reset
Ground
Power Button
The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off
the system. This button can also be con-
figured to function as a suspend button
(with a setting in the BIOS - see Chapter
4). To turn off the power when set to sus-
pend mode, press the button for at least
4 seconds. Refer to the table on the right
for pin definitions. (Note: Do not close or
short Pins 1 & 2 since this will cause the
system to continuously reboot.)
Power Button
Pin Definitions
Pin# Definition
1
2
Power On
Ground
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Reset
B. PWR Button
Intel G33
LED_Anode+
Power LED
HDD LED
NIC1 LED
LED_Anode+
LED_Anode+
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
X
X
Slot5 PCI-E x4
JBT1
Battery
OH/Fan Fail LED
JI2C1
JI2C2
LED_Anode+
JPL1
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
X
I-SATA4
I-SATA5
X
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
A
LE1
FP USB 7/8
FP USB 9/10
Reset
PWR
Reset Button
Ground
Ground
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Power Button
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2
1
B
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-6 Connecting Cables
ATX Power 24-pin Connector
Pin Definitions
Pin# Definition
Pin #
1
Definition
+3.3V
+3.3V
COM
ATX Main Power Connector
13
14
15
16
17
18
19
20
21
22
23
24
+3.3V
-12V
A 24-pin main power connector is
located at J40. This power connector
meets the SSI EPS 12V specifica-
tion. See the table on the right for pin
definitions.
2
COM
PS_ON
COM
COM
COM
Res (NC)
+5V
3
4
+5V
5
COM
6
+5V
7
COM
8
PWR_OK
5VSB
+12V
9
4-pin CPU Power Connector
+5V
10
11
12
+5V
+12V
A
4-pin 12V power connector is lo-
COM
+3.3V
cated at J41 on the motherboard. This
power connector also meets the SSI
EPS 12V specification, and is required
to ensure adequate power to the pro-
cessor. See the table on the right for
pin definitions.
12V 4-pin Power
Connector
Pin Definitions
Pins
Definition
Ground
+12V
1 and 2
3 and 4
B
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A
A. 24-pin ATX PWR
B. 4-pin PWR
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Universal Serial Bus (USB)
Back Panel USB (1-6)
Pin Definitions
There are 12 USB 2.0 (Universal
Serial Bus) ports/headers on the
motherboard. Six of them are Back
Panel USB ports: USB#1/2 (J11) and
USB#3/4/5/6 (J43). USB #7/8 (J44)
and USB#9/10 (J45) are headers
that can be used for front panel con-
nections. Additionally, USB#11(J47)
and USB#12 (J48) are onboard USB
connectors that can be accessed from
the front side of the chassis. See the
tables on the right for pin definitions.
Pin# Definitions
1
2
3
4
5
+5V
PO-
PO+
Ground
N/A
Front Panel USB (#7/8/9/10) and Front-
Accessible Onboard USB (#11/12)
Connections
Pin #
Definition
+5V
Pin #
Definition
+5V
1
2
3
4
5
1
2
3
4
5
PO-
PO-
PO+
Ground
Key
PO+
Ground
No connection
Chassis Intrusion
Chassis Intrusion
A Chassis Intrusion header is located
at JL1 on the motherboard. Attach an
appropriate cable from the chassis to
inform you of a chassis intrusion when
it is opened.
Pin Definitions
Pin# Definition
1
2
Intrusion Input
Ground
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Back panel USB Ports 1/2
B. Back panel USB Ports 3/4/5/6
C. Front Panel USB 7/8
D. Front Panel USB 9/10
E. USB 11
B
Intel G33
A
North Bridge
Slot7 PCI-E x1
F. USB 12
Slot6 PCI-E x16
G. Chassis Intrusion
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
D
I-SATA
C
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
Front-Access USB 11 G
JPUSB2
Front-Access USB 12
Slot1 PCI-33MHz
COM2
E
IDE#2
IDE#1
Buzzer
SPKR1
F
WOL
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Fan Headers
The C2SBA+II/C2SBA+/C2SBA/C2SBE
has five chassis fan headers (Fan 1 to Fan
5). Fan 1 is the CPU Fan. Fan 2 to Fan
5 are system/chassis fans. (Note: Pins
1-3 of a 4-pin fan headers are backward
compatible with the traditional 3-pin fans.)
See the table on the right for pin definitions.
The onboard fan speeds are controlled by
Thermal Management via BIOS Hardware
Monitoring in the Advanced Setting. (Note:
Default: Disabled. When using Thermal
Management settings, please use all 3-pin
fans or all 4-pin fans on the motherboard.)
Fan Header
Pin Definitions
Pin# Definition
1
2
3
4
Ground
+12V
Tachometer
PWR Modulation
VGA Connector
(Not available on the C2SBE)
A VGA connector (JG1) is located next to the
USB ports on the IO backplane. Refer to the
board layout below for the location.
CPU Fan
JKB
FAN2
B
A
4-Pin PWR
Processor
F
A. Fan 1 (CPU Fan)
B. Fan 2
Intel G33
C. Fan 3
E
D. Fan 4
North Bridge
Slot7 PCI-E x1
E. Fan 5
F. VGA
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JI2C2
JPL1
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
C
D
JP5
Audio Enabled
I-SATA4
I-SATA1
I-SATA5
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
ATX PS/2 Keyboard and
PS/2 Mouse Ports
PS/2 Keyboard and
Mouse Port Pin
Definitions
Pin# Definition
The ATX PS/2 keyboard and the PS/2
mouse are located at J28. See the
table on the right for pin definitions.
(The mouse port is above the key-
board port. See the table on the right
for pin definitions.)
1
2
3
4
5
6
Data
NC
Ground
VCC
Clock
NC
Serial Ports
Serial Port
Pin Definitions
COM1 (J31) is a connector located
on the IO Backpanel and COM2 is a
header located at J13. See the table
on the right for pin definitions.
Pin #
Definition
DCD
Pin #
Definition
DSR
1
2
3
4
5
6
7
8
9
RXD
RTS
CTS
RI
TXD
DTR
Ground
10
NC
(Pin 10 is available on COM2
only. NC: No Connection.)
CPU Fan
JKAB
FAN2
4-Pin PWR
Processor
B
A. Keyboard/Mouse
B. COM1
Intel G33
C. COM2
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
PCI-33MHz
CSlot1
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Wake-On-Ring
The Wake-On-Ring header is des-
ignated JWOR. This function allows
your computer to receive and be
"awakened" by an incoming call when
in the suspend state. See the table on
the right for pin definitions. You must
have a Wake-On-Ring card and cable
to use this feature.
Wake-On-Ring
Pin Definitions
Pin# Definition
1
2
Ground
Wake-up
Wake-On-LAN
Wake-On-LAN
Pin Definitions
The Wake-On-LAN header is located
at JWOL on the motherboard. See the
table on the right for pin definitions.
(You must also have a LAN card with
a Wake-On-LAN connector and cable
to use this feature.)
Pin# Definition
1
2
3
+5V Standby
Ground
Wake-up
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. WOR
B. WOL
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
A
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
Slot2 PCI-33MHz
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
B
IDE#1
WOL
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
GLAN 1 (Giga-bit Ethernet
Port)
A G-bit Ethernet port is located at J11
on the IO backplane. This port accepts
RJ45 type cables.
GLAN1
Speaker
A Speaker/Buzzer header (J9) is
Speaker Connector
Pin Definitions
located on the motherboard. See the
table on the right for speaker pin defi-
nitions. Note: The speaker connector
pins are for use with an external
speaker. If you wish to use the on-
board speaker, you should close pins
3-4 with a jumper.
Pin Setting Definition
Pins 3-4 Internal Speaker
Pins 1-4 External Speaker
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. GLAN1
Intel G33
B. Speaker/Buzzer
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
B
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
High Definition Audio (HDA)
TheC2SBA+II/C2SBA+/C2SBA/C2SBEfeatures
a 7.1+2 Channel High Definition Audio (HDA)
(J46) codec that provides 10DAC channels,
simultaneously supporting 7.1 sound playback
and two channels of independent stereo sound
output(multiplestreaming)throughthefrontpanel
stereo out for front L&R, rear L&R, center and
subwoofer speakers. This feature is activated
with theAdvanced software in the CD-ROM that
came with your motherboard. Sound is then
output through the Line In, Line Out and MIC
jacks (See at the picture at right).
Orange:
CEN/LFE
Blue: Line-In
Black: Back
Surround
Green:Front
Pink: Mic-In
Grey: Side
Surround
CD Header
A 4-pin CD header is located at CD1, and an
Auxiliary header is located at J12 on the moth-
erboard. These headers allow you to use the
onboard sound for audio CD playback. Con-
nect an audio cable from your CD drive to the
header that fits your cable's connector. Only
one CD header can be used at any one time.
See the tables at right for pin definitions.
CD1 Pin Definition
Definition
Pin#
1
2
3
4
Left Stereo Signal
Ground
Ground
Right Stereo
Signal
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. HD Audio
B. CD-In
Intel G33
C. Front Panel Audio
A
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
B
C
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Front Panel Audio Control
Whenfrontpanelheadphonesareplugged
in, the back panel audio output is disabled.
High Definition Front Panel Audio
This is done through the FP Audio header
(J12). If the front panel interface card is not
connected to the front panel audio header,
jumpers should be installed on the header
(J12) pin pairs: 1-2, 5-6, and 9-10. If these
jumpers are not installed, the back panel
line out connector will be disabled and
microphone input Pin 1 will be left floating,
which can lead to excessive back panel
microphone noise and cross talk. See the
table below for pin definitions.
Pins# Signal
ꢀ
0,&B/
ꢁ
ꢂ
$8'B*1'
0,&B5
ꢃ
ꢄ
)3B$XGLRꢀ'HWHFWꢁ
/LQHBꢂB5ꢁ
ꢅ
ꢆ
ꢇ
3XOOꢁGRZQꢁWRꢁ*URXQGꢁ
)3B-DFNꢀ'HWHFWꢁ
.H\
ꢈ
/LQHBꢂB/ꢁ
ꢀꢉ
3XOOꢁGRZQꢁWRꢁ*URXQGꢁ
Power LED
PWR LED
Pin Definitions
The Power LED connector is designated
JLED. This connection is used to provide
LED Indication of power supplied to the
system. See the table on the right for pin
definitions.
Pin# Definition
1
2
3
+5V
Key
Ground
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Front Panel Audio
B. PWR LED
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
B
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
CD-IN
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
A
Front Audio
JL1
IDE CTRL
ITE 8212
Speaker
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-7 Jumper Settings
Explanation of
Jumpers
3
2
1
Connector
Pins
To modify the operation of the
motherboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identified with a
square solder pad on the printed circuit
board. See the motherboard layout
pages for jumper locations.
Jumper
Cap
3
2
1
Setting
Pin 1-2 short
Note: On two pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.
GLAN Enable/Disable
GLAN Enable
Jumper Settings
JPL1 enables or disables the GLAN
Port on the motherboard. See the
table on the right for jumper settings.
The default setting is enabled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. GLAN Port1 Enable
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
A
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
Slot3 PCI-33MHz
Slot2 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent the accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note: For an ATX power supply, you must completely shut down the system, remove
the AC power cord and then short JBT1 to clear CMOS.
Watch Dog Enable/Disable
Watch Dog is a system monitor that can reboot
the system when a software application hangs.
Watch Dog
Jumper Settings
Close pins 1-2 to reset the system if an applica-
Jumper Setting Definition
tion hangs. Close pins 2-3 to generate a non-
Pins 1-2
Reset
(default)
maskable interrupt signal for the application that
hangs. See the table on the right for jumper set-
tings. Watch Dog must also be enabled in the
BIOS. (Note: When enabled, the user needs to
write his/her own application software to disable
the Watch Dog Timer.)
Pins 2-3
Open
NMI
Disabled
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Clear CMOS
B. Watch Dog Enable
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
J
Battery
A
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
B
I-SATA4
I-SATA5
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
PCI/PCI-E Slots to SMB
Speeds
SMBus to PCI-X/PCI-Exp Slots
Jumper Settings
Jumper Setting Definition
Jumpers JI2C1/JI2C2 allow you to con-
nect PCI/PCI-Exp. Slots to the System
Management Bus. The default setting is
open to disable the connection. See the
table on the right for jumper settings.
Closed
Open
Enabled
Disabled (Default)
Keyboard Wake-Up
The JKB jumper is used together with
the Keyboard Wake-Up function in BIOS.
Enable the jumper and the BIOS setting to
allow the user to "wake the system up" by
hittingakeyonthekeyboard. Seethetable
ontherightforjumpersettings. Yourpower
supply must meet ATX specification 2.01
or higher and supply 720 mA of standby
power to use this feature.
KB Wake-up Enable
Jumper Settings
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
CPU Fan
JKB
FAN2
4-Pin PWR
C
Processor
A. JI2C1
B. JI2C2
Intel G33
C. Keyboard Wake-Up
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
A
JI2C1
JPL1
B JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
Slot2 PCI-33MHz
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
IDE Enable/Disable
IDE Enable
Jumper Settings
JP2 enables or disables IDE#1 and
IDE#2 on the C2SBA+II/C2SBA+.
See the table on the right for jumper
settings.The default setting is en-
abled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
TPM Enable (For the
C2SBA/C2SBA+II/C2SBA+)
TPM Enable
Jumper Settings
Use JP3 to enable or disable Trust
PlatformModuleManagement(TPM)
on the motherboard. See the table
on the right for jumper settings. The
default setting is Enabled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. IDE Enable
B. TPM Enable
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
B
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
A
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Audio Enable
Audio Enable
Jumper Settings
JP5 enables or disables the onboard
audioconnections.Seethetableonthe
right for jumper settings. The default
setting is Enabled.
Pin# Definition
1-2
2-3
Enabled (default)
Disabled
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Audio Enable
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Abled
A
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
USB Wake-Up
Use JPUSB jumpers (JPUSB1/JPUSB2) to en-
able the function of "System Wake-Up via USB
devices", which allows you to "wake-up" the
system by pressing a key on the USB keyboard
USB Wake-up Enable
Jumper Settings
Pin# Definition
1-2
2-3
Enabled
Disabled
or by clicking the USB mouse of your system.
The JPUSB jumpers are used together with the
USB Wake-Up function in the BIOS. Enable
both jumpers and the BIOS setting to allow the
system to "wake-up via USB Devices". See the
table on the right for jumper settings and jumper
connections. (Note: JPUSB1 is for Back Panel
USB ports:1/2/3/4/5/6, and JPUSB2 is for Front
Panel USB ports:7/8/9/10 and Front Accessible
USB ports: 11/12.)
(Note: The default jumper setting for the USB
ports is "Disabled". However, when the "USB
Wake-Up" function is enabled in the BIOS and
the desired USB ports are enabled via the
JPUSB jumper, please be sure to remove all
USB devices from the USB ports whose USB
jumpers are set to "Disabled" before the system
goes into the standby mode.)
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. JPUSB1
B. JPUSB2
Intel G33
A
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
ont-Access USB 12
Front-Access USB 11
B
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-8 Onboard Indicators
GLAN Link/Speed LED Indicator
GLAN LEDs
LED Color
Definition
There is one Gigabit-LAN port (J11). This
Gigabit Ethernet LAN port has two LEDs.
The yellow GLAN Activity LED (right, see
below) indicates activity, while the GLAN
Link/Speed LED (left) may be green,
amber or off to indicate the speed of the
connection. See the tables at right for
more information.
Off
No Connection or 10 Mbps
100 Mbps
Green (On)
Amber (On)
1 Gbps
GLAN Activity LED Indicator
Color
Yellow (Flashing)
Definition
ConnectionActive
GLAN Link/Speed LED
GLAN Activity LED
Rear View
(When viewing from the rear side
of the chassis.)
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. GLAN Port1 LEDs
Intel G33
A
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JI2C2
JPL1
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
CD-IN
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Onboard Power LED (LE1)
Onboard PWR LED Indicator
The Onboard 3.3V Standby Power LED is
located at LE1 on the motherboard. When
LE1 is off, the system is off. When the
green light is on, the system is on. When
the LED is on, the power is on. Unplug the
power cable before removing or installing
components. See the layout below for the
LED location.
Settings
LED Color Definition
Off
System Off
On
Standby Power On
System On
Green
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Power LED
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
A
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2-9 Parallel Port, Floppy Drive and IDE Hard Drive
Connections
Note the following when connecting the floppy and hard disk drive cables:
•
•
•
The floppy disk drive cable has seven twisted wires.
A red mark on a wire typically designates the location of pin 1.
A single floppy disk drive ribbon cable has two connectors to provide for two
floppy disk drives. The connector with twisted wires always connects to drive
A, and the connector that does not have twisted wires always connects to drive
B.
Parallel (Printer) Port Connector
Pin Definitions
Pin# Definition
Pin #
2
Definition
Auto Feed-
Error-
Parallel (Printer) Port
Connector
1
Strobe-
3
Data Bit 0
Data Bit 1
Data Bit 2
Data Bit 3
Data Bit 4
Data Bit 5
Data Bit 6
Data Bit 7
ACK
4
5
6
Init-
The parallel (printer) port is located
at J30. See the table on the right for
pin definitions.
7
8
SLCT IN-
GND
9
10
12
14
16
18
20
22
24
26
11
13
15
17
19
21
23
25
GND
GND
GND
GND
GND
BUSY
Write Data
Write Gate
NC
PE
SLCT
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A
A. Parallel Port
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JPL1
JI2C2
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
CD-IN
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA5
I-SATA1
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Floppy Connector
Floppy Drive Connector
Pin Definitions
The floppy connector is located at
J27. See the table on the right for pin
definitions.
Pin# Definition
Pin #
2
Definition
FDHDIN
1
Ground
Ground
Key
3
4
Reserved
FDEDIN
5
6
7
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
8
Index
9
10
12
14
16
18
20
22
24
26
28
30
32
34
Motor Enable
Drive Select B
Drive Select B
Motor Enable
DIR
11
13
15
17
19
21
23
25
27
29
31
33
STEP
Write Data
Write Gate
Track 00
Write Protect
Read Data
Side 1 Select
Diskette
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. Floppy
Intel G33
A
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JI2C2
JPL1
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA1
I-SATA5
CD-IN
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
IDE#1
WOL
2-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
IDE Connectors (For the
C2SBA+II/C2SBA+ only)
IDE Drive Connectors
Pin Definitions
Pin# Definition
Pin #
2
Definition
Ground
There are two IDE connectors on the
C2SBA+II/C2SBA+. Be sure to close
Pin 1 and Pin 2 of JP2 to enable the
IDE connectors before using them.
(Please refer to the jumper section for
more details.) See the table on the right
for pin definitions.
1
Reset IDE
Host Data 7
Host Data 6
Host Data 5
Host Data 4
Host Data 3
Host Data 2
Host Data 1
Host Data 0
Ground
3
4
Host Data 8
Host Data 9
Host Data 10
Host Data 11
Host Data 12
Host Data 13
Host Data 14
Host Data 15
Key
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
DRQ3
Ground
I/O Write
I/O Read
IOCHRDY
DACK3
Ground
Ground
BALE
Ground
IRQ14
IOCS16
Addr1
Ground
Addr0
Addr2
Chip Select 0
Activity
38
40
Chip Select 1
Ground
CPU Fan
JKB
FAN2
4-Pin PWR
Processor
A. IDE#1
B. IDE#2
Intel G33
North Bridge
Slot7 PCI-E x1
Slot6 PCI-E x16
GLAN CTRL
Slot5 PCI-E x4
JBT1
Battery
JI2C1
JI2C2
JPL1
JWOR
Intel ICH9(R)
South Bridge
JP3
JWD
JLED
I-SATA2
Audio CTRL
I-SATA3
I-SATA0
Slot4 PCI-33MHz
JP5
Audio Enabled
I-SATA4
I-SATA1
I-SATA5
CD-IN
Slot3 PCI-33MHz
Slot2 PCI-33MHz
BIOS
LE1
FP USB 7/8
FP USB 9/10
JL1
IDE CTRL
ITE 8212
Speaker
Front Audio
JPUSB2
Front-Access USB 12
Front-Access USB 11
Slot1 PCI-33MHz
COM2
IDE#2
Buzzer
SPKR1
B
A
IDE#1
WOL
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Notes
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1
Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any
hardware components.
Before Power On
1. Make sure that there are no short circuits between the motherboard and chas-
sis.
2. Disconnect all ribbon/wire cables from the motherboard, including those for the
keyboard and mouse.
3. Remove all add-on cards.
4. Install a CPU and heatsink (making sure it is fully seated) and connect the
chassis speaker and the power LED to the motherboard. Check all jumper
settings as well.
5. Use the correct type of onboard CMOS battery as specified by the Manufacturer.
Do not install the CMOS battery upside down to avoid possible explosion.
6. Make sure that the 4-pin 12v power connector at J41 is connected to your
power supply.
No Power
1. Make sure that there are no short circuits between the motherboard and chas-
sis.
2. Verify that all jumpers are set to their default positions.
3. Check that the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to verify that it still sup-
plies ~3VDC. If it does not, replace it with a new one.
No Video
1. If the power is on but you have no video, remove all the add-on cards and
cables.
2. Use the speaker to determine if any beep codes exist. Refer to Appendix A for
details on beep codes.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
NOTE
If you are a system integrator, VAR or OEM, a POST diagnostics
card is recommended. For I/O port 80h codes, refer to App. B.
Memory Errors
1. Make sure that the DIMM modules are properly and fully installed.
2. You should be using unbuffered DDR2 memory (see the next page). Also, it
is recommended that you use the same memory speed for all DIMMs in the
system. See Section 2-4 for memory limitations.
3. Check for bad DIMM modules or slots by swapping modules between slots and
noting the results.
4. Check the power supply voltage 115V/230V switch.
Losing the System’s Setup Configuration
1. Make sure that you are using a high quality power supply. A poor quality power
supply may cause the system to lose the CMOS setup information. Refer to
Section 1-6 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still sup-
plies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the Setup Configuration problem, contact your
vendor for repairs.
3-2 Technical Support Procedures
Before contacting Technical Support, please take the following steps. Also, note
that as a motherboard manufacturer, Super Micro does not sell directly to end-us-
ers, so it is best to first check with your distributor or reseller for troubleshooting
services. They should know of any possible problem(s) with the specific system
configuration that was sold to you.
1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked
Question' (FAQ) sections in this chapter or see the FAQs on our web site
(http://www.supermicro.com/support/faqs/) before contacting Technical
Support.
2. BIOS upgrades can be downloaded from our web site at (http://www.supermicro
com/support/bios/).
Note: Not all BIOS can be flashed; it depends on the modifications to the
boot block code.
3. If you still cannot resolve the problem, include the following information when
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
contacting Super Micro for technical support:
•
•
Motherboard model and PCB revision number
BIOS release date/version (this can be seen on the initial display when your
system first boots up)
•
System configuration
An example of a Technical Support form is on our web site at (http://www.
supermicro.com/support/contact.cfm).
4. Distributors: For immediate assistance, please have your account number ready
when placing a call to our technical support department. We can be reached
by e-mail at [email protected], by phone at:(408) 503-8000, option
2, or by fax at (408)503-8019.
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The C2SBA+II/C2SBA+/C2SBA/C2SBE supports unbuffered, DDR2
667/800 MHz memory modules. See Section 2-4 for details on installing
memory.
Question: Why does Microsoft Windows XP (SP2) and Windows Vista show
less memory than what is physically installed?
Answer: Microsoft implemented a design change in Windows XP with Service
Pack 2 (SP2) and Windows Vista. This change is specific to the Physical Ad-
dress Extension (PAE) mode behavior which improves driver compatibility. For
more information, please read the following article at Microsoft’s Knowledge
Base website at: http://support.microsoft.com/kb/888137.
Question: How do I update my BIOS?
Answer: It is recommended that you do not upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS files are located
on our web site at http://www.supermicro.com/support/bios/. Please check our
BIOS warning message and the information on how to update your BIOS on our
web site. Select your motherboard model and download the BIOS (.rom) file to
your computer. Also, check the current BIOS revision and make sure that it is
newer than your BIOS before downloading. You may choose the zip file or the
.exe file. If you choose the zipped BIOS file, please unzip the BIOS file onto a
bootable device or a USB pen/thumb drive. To flash the BIOS, run the batch
file named "flash.bat" with the new BIOS .rom file from your bootable device or
USB pen/thumb drive. Use the following format:
F:\> flash xxxxxxxx.rom <Enter>
Note: Be sure to insert a space immediately after "flash" and use only the file
named “flash.bat” to update the BIOS.
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
When completed, your system will automatically reboot. If you choose the .exe
file, please run the .exe file under Windows to create the BIOS flash floppy disk.
Insert the floppy disk into the system you wish to flash the BIOS. Then, boot
the system to the floppy disk. The BIOS utility will automatically flash the BIOS
without any prompts. Please note that this process may take a few minutes to
complete. Do not be concerned if the screen is paused for a few minutes.
Warning: Do not shut down or reset the system while updating the BIOS to
prevent possible system boot failure!
When the BIOS flashing screen is completed, the system will reboot and will
show “Press F1 or F2”. At this point, you will need to load the BIOS defaults.
Press <F1> to go to the BIOS setup screen, and press <F9> to load the default
settings. Next, press <F10> to save and exit. The system will then reboot.
Note: The SPI BIOS chip installed on this motherboard is not removable. To
repair or replace a damaged BIOS chip, please send your motherboard to RMA
at Supermicro for service.
Question: What's on the CD that came with my motherboard?
Answer: The supplied compact disc has quite a few drivers and programs that
will greatly enhance your system. We recommend that you review the CD and
install the applications you need. Applications on the CD include chipset drivers,
security and audio drivers.
Question: How do I utilize the onboard HD sound?
Answer: The onboard HD sound available on the C2SBA+II/C2SBA+/C2SBA/
C2SBE can be enabled with the audio driver software that was included in your
motherboard package. When activated, sound will be routed through the jacks
next to the LAN Port according to the audio connection descriptions listed on
Page 2-8. You must also set the HD Audio setting to "Auto" in the Advanced
Chipset section of the BIOS setup.
Question: I installed my microphone correctly but I can't record any sound.
What should I do?
Answer: Go to <Start>, <Programs>, <Accessories>, <Entertainment> and then
<Volume Control>. Under the Properties tab, scroll down the list of devices in
the menu and check the box beside "Microphone".
Question: After I have installed 4 pieces of 1GB Memory, why does the BIOS
only detect about 3.145 GB of memory during POST?
Answer: Because the chipset does not support memory remapping, and PCI-E
memory requires a great deal of memory, so there is a memory hole located
around the 4GB memory address.
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Troubleshooting
Question: How do I connect the ATA100/66 cable to my IDE device(s)?
Answer: The 80-wire/40-pin high-density ATA100/66 IDE cable that came
with your system has two connectors to support two drives. This special cable
must be used to take advantage of the speed the ATA100/66 technology offers.
Connect the blue connector to the onboard IDE header and the other
connector(s) to your hard drive(s). Consult the documentation that came with
your disk drive for details on actual jumper locations and settings.
Question: Why doesn't by USB devices no longer work correctly after
installing the Intel Chipset Software Installation Utility in Windows XP or
Windows Server 2003?
Answer: This is a timing conflict between Windows File Protection and the
Setup program. This is described in greater detail, and a hotfix is available at
Microsoft's website at http://support.microsoft.com/kb/921411/en-us
3-4 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required
before any warranty service will be rendered. You can obtain service by calling
your vendor for a Returned Merchandise Authorization (RMA) number. When
returning to the manufacturer, the RMA number should be prominently displayed
on the outside of the shipping carton, and mailed prepaid or hand-carried. Ship-
ping and handling charges will be applied for all orders that must be mailed when
service is complete.
This warranty only covers normal consumer use and does not cover damages
incurred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product prob-
lems.
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Chapter 4
BIOS
4-1
Introduction
This chapter describes the Phoenix BIOS™ Setup utility for the C2SBA+II/
C2SBA+/C2SBA/C2SBE. The Phoenix ROM BIOS is stored in a flash chip and
can be easily upgraded using a floppy disk-based program.
Note: Due to periodic changes to the BIOS, some settings may have been added
or deleted and might not yet be recorded in this manual. Please refer to the Manual
Download area of the Super Micro web site <http://www.supermicro.com> for any
changes to the BIOS not reflected in this manual.
System BIOS
The BIOS is the Basic Input Output System used in all IBM® PC, XT™, AT®, and
PS/2® compatible computers. The Phoenix BIOS stores the system parameters,
types of disk drives, video displays, etc. in the CMOS. The CMOS memory re-
quires very little electrical power. When the computer is turned off, a backup battery
provides power to the CMOS logic, enabling it to retain system parameters. Each
time the computer is powered on, the computer is configured with the values stored
in the CMOS logic by the system BIOS, which gains control at boot-up.
How To Change the Configuration Data
The CMOS information that determines the system parameters may be changed
by entering the BIOS Setup utility. This Setup utility can be accessed by pressing
the <Delete> key at the appropriate time during system boot. (See below.)
Starting the Setup Utility
Normally, the only visible POST (Power On Self Test) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu
of the BIOS Setup utility. From the main menu, you can access the other setup
screens, such as the Security and Power menus. Beginning with Section 4-3,
detailed descriptions are given for each parameter setting in the Setup utility.
Warning: Do not shut down or reset the system while updating the BIOS
to prevent possible boot failure.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
4-2
Running Setup
Default settings are in bold text unless otherwise noted.
The BIOS setup options described in this section are selected by choosing the ap-
propriate text from the main BIOS Setup screen. All displayed text is described in
this section, although the screen display is often all you need to understand how
to set the options (See the next page).
When you first power on the computer, the Phoenix BIOS™ is immediately acti-
vated.
While the BIOS is in control, the Setup program can be activated in one of two
ways:
1. By pressing <Delete> immediately after turning the system on, or
2. When the message shown below appears briefly at the bottom of the screen
during the POST (Power On Self-Test), press the <Delete> key to activate
the main Setup menu. Press the <Delete> key to enter Setup
4-3
Main BIOS Setup
All main Setup options are described in this section. The main BIOS Setup screen
is displayed below.
Use the Up/Down arrow keys to move among the different settings in each menu.
Use the Left/Right arrow keys to change the options for each setting.
Press the <Esc> key to exit the CMOS Setup Menu. The next section describes in
detail how to navigate through the menus.
Items that use submenus are indicated with the icon. With the item highlighted,
press the <Enter> key to access the submenu.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Main BIOS Setup Menu
Main Setup Features
System Time
To set the system date and time, key in the correct information in the appropriate
fields. Then press the <Enter> key to save the data.
System Date
Using the arrow keys, highlight the month, day and year fields, and enter the correct
data. Press the <Enter> key to save the data.
Legacy Diskette A
This setting allows the user to set the type of floppy disk drive installed as diskette A.
The options are Disabled, 360Kb 5.25 in, 1.2MB 5.25 in, 720Kb 3.5 in, 1.44/1.25MB,
3.5 in and 2.88MB 3.5 in.
BIOS Date
The item displays the date that the BIOS was built.
Hard Disk Pre-Delay
Select Enable to allow for the time needed for a hard drive to perform initialization
before it is accessed by the BIOS after power-up to prevent possible system boot
failure. A boot failure may occur if the BIOS accesses a hard drive that has not
been properly initialized. The default setting is Disabled.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Serial ATA
This setting allows the user to enable or disable the function of the Serial ATA. The
options are Disabled and Enabled.
Native Mode Operation
Select Serial ATA for SATA or select Auto (Native Mode) for ATA. The options are:
Serial ATA and Auto.
Serial ATA (SATA) RAID Enable (C2SBA+II Only)
Select Enable to enable Serial ATA RAID Functions. (For the Windows OS
environment, use the RAID driver if this feature is set to Enabled. When this item
is set to Enabled, the item: "ICH RAID Code Base" will be available for you to select
either Intel or Adaptec Host RAID firmware. If this item is set to Disabled, the item-
SATA AHCI Enable will be available.) The options are Enabled and Disabled.
SATA AHCI Enable
Select Enabled to use the Serial ATA Advanced Host Interfacing. This feature is
available when the Windows XP OS, the SPI BIOS Chip, and the IAA Driver are
installed in the system. (Take caution when using this function. This feature is for
advanced programmers only. The options are Enabled and Disabled.)
SATA AHCI Legacy Enable
Select Enabled use the SATA Advanced Host Interface Legacy Mode. When in
AHCI Legacy Mode, SATA Port 5 and SATA Port 6 are disabled. (Take caution when
using this function. This feature is for advanced programmers only. The options
are Enabled and Disabled.)
SATA Port1, SATA Port2, SATA Port3, SATA Port4 and SATA 5
These settings allow the user to set the parameters of slots indicated above. Hit
<Enter> to access the following sub-menu screen. Set the correct configurations
accordingly.
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Type
This option allows you to select the type of IDE hard drive. Select Auto to allow
BIOS to automatically detect the hard drive's capacity, number of heads, etc.).
The option User allows the user to enter the parameters for the HDD installed
at this connection. Enter a number between 1 to 39 to select a predetermined
HDD type. Select CDROM if a CDROM drive is installed. Select ATAPI if a
removable disk drive is installed.
CHS Format
The following items will be displayed by the BIOS:
TYPE: This item displays the type of IDE or SATA Device.
Cylinders: This item indicates the status of Cylinders.
Headers: This item indicates the number of headers.
Sectors: This item displays the number of sectors.
Maximum Capacity: This item displays the maximum storage capacity of
the system.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
LBA Format
The following items will be displayed by the BIOS:
Total Sectors: This item displays the number of total sectors available in the
LBA Format.
Maximum Capacity: This item displays the maximum capacity in the LBA
Format.
Multi-Sector Transfers
This item allows the user to specify the number of sectors per block to be used
in the multi-sector transfer. The options are Disabled, 4 Sectors, 8 Sectors, and
16 Sectors.
LBA Mode Control
This item determines whether the Phoenix BIOS will access the IDE Channel 0
Master Device via the LBA mode. The options are Enabled and Disabled.
32 Bit I/O
This option allows the user to enable or disable the function of a 32-bit data
transfer. The options are Enabled and Disabled.
Transfer Mode
This option allows the user to set the transfer mode. The options are Standard,
Fast PIO1, Fast PIO2, Fast PIO3, Fast PIO4, FPIO3/DMA1 and FPIO4/DMA2.
Ultra DMA Mode
This option allows the user to select Ultra DMA Mode. The options are Disabled,
Mode 0, Mode 1, Mode 2, Mode 3, Mode 4, and Mode 5.
Installed Memory
This display informs you how much system memory is recognized as being present
in the system.
System Memory
This display informs you how much memory is available in the system.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-4
Advanced Setup
Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display. The items with a triangle beside them have
sub- menus that can be accessed by highlighting the item and pressing <Enter>.
Boot Features
Floppy Check
Select Enabled to allow the BIOS to verify the type of floppy drive at bootup. Select
Disabled to speed up the boot process. The settings are Enabled and Disabled.
Quiet Boot
This setting allows you to Enable or Disable the graphic logo screen display during
bootup.
QuickBoot Mode
If enabled, this feature will speed up the POST (Power On Self Test) routine by
skipping certain tests after the computer is turned on. The settings are Enabled
and Disabled. If Disabled, the POST routine will run at normal speed.
POST Errors
Select Enabled to stop the POST routine and allow the system to display error mes-
sages when an error occurs at bootup. The options are Enabled and Disabled.
ACPI Mode
Use this setting to determine whether you want to use the ACPI (Advanced
Configuration and Power Interface) power management on your system. The
options are Yes and No.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
ACPI Sleep Mode
This setting allows you to configure theACPI (Advanced Configuration and Power
Interface) Sleep Mode for your system. The options are S1, S3 and S1S3.
High Precision Event Time
Select Yes to activate the High Precision Event Timer (HPET) that produce
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) can
in synchronizing multimedia streams, providing smooth playback and reducing
the dependency on other timestamp calculation devices, such as an x86 RDTSC
Instruction embedded in a CPU. The High Precision Event Timer is used to replace
the 8254 Programmable Interval Timer. The default setting is No.
Power Button Behavior
If set to Instant-Off, the system will power on or power off the system immediately
as soon as the user hits the power button. The options are Instant-Off and 4-second
Override.
Resume On Modem Ring
Select On to “wake your system up” when an incoming call is received by your
modem. The options are On and Off.
Resume On PME#
Select On to “wake your system up” from the PME#. The options are On and
Off.
PS2 Keyboard (KB)/Mouse Wake Up
Select Enable to “wake your system up” from S3, S4 or S5 state. The options are
Enabled and Disabled. (This feature is available when the jumper-JKB is enabled
by closing pin 1 and pin 2. Please refer to Chapter 2.)
USB Wake Up
This feature is used to awaken the system from Standby mode by a Universal Se-
rial Bus (USB) device (such as, a USB mouse or USB keyboard). The options are
Enabled and Disabled.
Power Loss Control
This setting allows you to decide how the system will react when power returns
after an unexpected loss of power. The options are Stay Off, Power On, and
Last State.
Legacy USB Support
Select Enabled to enable Legacy USB Support. The options are Enabled and
Disabled.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Watch Dog
Select Enabled to automatically reset the system if the system is not active for
more than 4 minutes. The options are Enabled and Disabled.
Summary Screen
This setting allows you to Enable or Disable the summary screen which displays
the system configuration during bootup.
Advanced Processor Options
Access the submenu to make changes to the following settings.
CPU Speed
This is a display that indicates the speed of the installed processor.
CPU Overclocking (Available when supported by the CPU)
This feature allows the user to enable and configure Overclocking settings in order
to boost system performance. The options are: Disabled, +5%, +10%, and +15%.
Please note that Supermicro does not recommend CPU Overclocking because it
might cause the system to become unstable. The default setting is Disabled. If this
feature is not set to Disabled, the following two items will display.
CPU OverVoltage (Available when supported by the CPU)
This feature allows the CPU to operate at higher voltage settings than normal
settings. The options are: Disabled, +5%, +10%, and +15%. Please note that
Supermicro does not recommend CPU OverVoltage because it might cause the
system to become unstable. The default setting is Disabled.
Memory OverVoltage (Available when supported by the CPU)
This feature allows memory modules to operate at higher voltage settings than
normal settings. The options are: Disabled, +5%, +10%, and +15%. Please note
that Supermicro does not recommend Memory OverVoltage because it might
cause the system to become unstable. The default setting is Disabled.
Core-Multi-Processing (Available when supported by the CPU)
Set to Enabled to use a processor's Second Core and beyond. (Please refer to
Intel's web site for more information.) The options are Disabled and Enabled.
Machine Checking (Available when supported by the CPU)
Set to Enabled to activate the function of Machine Checking and allow the CPU to
detect and report hardware (machine) errors via a set of model-specific registers
(MSRs). The options are Disabled and Enabled.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Fast String Operations (Available when supported by the CPU)
Set to Enabled to enable the fast string operations for special CPU instructions.
The options are Disabled and Enabled.
Compatible FPU Code (Available when supported by the CPU)
Set to Enabled to keep the content of the last instruction Operating Code (OPCode)
in the floating point (FP) state. The options are Disabled and Enabled.
Split Lock Operation
Set to Enabled to mask alignment check exceptions for split-lock transactions. The
options are Disabled and Enabled.
Thermal Management 2 (Available when supported by the CPU)
Set to Enabled to use theThermal Management 2 (TM2)Technology, which will lower
the CPU voltage and frequency when the CPU temperature reaches a predefined
overheat threshold. Set to Disabled to use Thermal Manager 1 (TM1), and allow
CPU clocking to be regulated via the CPU Internal Clock modulation when the CPU
temperature reaches the overheat threshold.
Adjacent Cache Line Prefetch (Available when supported by the
CPU)
The CPU fetches the cache line for 64 bytes if this option is set to Disabled. The
CPU fetches both cache lines for 128 bytes as comprised if Enabled. The options
are Disabled and Enabled.
Set Maximum Ext. CPUID=3
When set to Enabled, the Maximum Extended CPUID will be set to 3. The options
are Disabled and Enabled.
Echo TPR
Set to Enabled to prevent xTPR messages from being sent to the system. The
options are Disabled and Enabled.
C1 Enhanced Mode (Available when supported by the CPU)
Set to Enabled to enable the Enhanced Halt State to lower CPU voltage/frequen-
cy to prevent overheat. The options are Enabled and Disabled. (Note: Please
refer to Intel’s web site for detailed information.)
Intel® Virtualization Technology (Available when supported by the
CPU)
Select Enabled to use the feature of Virtualization Technology to allow one platform
to run multiple operating systems and applications in independent partitions,
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
creating multiple virtual systems in one computer. The options are Enabled and
Disabled. (Note: If there is any change to this setting, you will need to power off
and restart the system for the change to take effect.) Please refer to Intel’s web
site for detailed information.
No Execute Mode Memory Protection (Available when supported by
the CPU and the OS)
Set to Enabled to enable Execute Disable Bit and allow the processor to classify
areas in memory where an application code can execute and where it cannot, and
thus preventing a worm or a virus from inserting and creating a flood of codes to
overwhelm the processor or damage the system during an attack. The options
are Disabled and Enabled. For more information, please visit Intel and Microsoft
web sites.
Intel Speed Step Support (Available when supported by the CPU.)
Select Enabled to use the Enhanced Intel SpeedStep Technology and allow the
system to automatically adjust the processor voltage and core frequency in an effort
to reduce power consumption and heat dissipation. The options are Enabled (-C
States, GV1/GV3 are enabled), GV1/GV3 Only (C States: Disabled), C-States Only
(-G1/G3: Disabled), and Disabled (-C States, GV1/GV3 are disabled). Please refer
to Intel’s web site for detailed information.
Advanced Chipset Control
Access the submenu to make changes to the following settings.
Warning: Take caution when changing the Advanced settings. An incorrect
setting, a very high DRAM frequency or an incorrect DRAM timing may result in
system instability. When this occurs, reset the setting to the default setting.
Clock Spectrum Feature
When set to Enabled, the BIOS will monitor the level of Electromagnetic Interference
caused by the components and will attempt to decrease the interference whenever
needed. The options are Enabled and Disabled.
Integrated Device Control Sub-menu
USB Host Controller 1
This feature allows the user to configure the control setting for USB Host Controller
1. The default setting is Enabled.
USB Host Controller 2
This feature allows the user to configure the control setting for USB Host Controller
2. The default setting is Enabled.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Memory Reclaiming
Select Enable to enable the functionality of Memory Remapping above 4GB. The
settings are Enabled and Disabled.
Enable VT-d
Select Enabled to enable Intel's Virtualization Technology support for Direct I/O VT-d
by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.
This feature offers fully-protected I/O resource-sharing across the Intel platforms,
providing the user with greater reliability, security and availability in networking and
data-sharing. The settings are Enabled and Disabled.
Default Primary Video Adapter
This feature allows the user to select the video device used by the BIOS during
POST. If set to Auto, PEG, PCI, IGD (Internal Graphics Device) devices will be
selected. If set to IGD (Internal Graphics Device), IGD and PCI devices will be
selected. If set to PEG, PEG and PCI devices will be selected. If set to PCI, PCI,
PEG and IGD devices will be selected. IGD-Device 2
This feature allows the user to enable or disable Internal Graphics Device#2 by
entering a specified value.
IGD-Device 2, Function 1
Select Enabled to enable Function#1 of Internal Graphics Device#2, which will allow
IGD-Device2 to use a 2nd Adaptor by entering a specified value. The options are
Auto and Disabled.
DVMT 4.0 Mode
This feature allows the user to configure the DVMT 4.0 Graphics Memory to be used
by the Internal Graphics Device. The options are Fixed, DVMT and Auto.
Pre-allocated Memory Size
This feature allows the user to set the total amount of Pre-allocated graphics memory
to be used by the Internal Graphics Device. The options are 1 MB and 8 MB.
IGD Memory Size
This feature allows the user to set the total amount of graphics memory to be used by
the Internal Graphics Device. The settings are 128 MB, 256 MB and MAXDVMT.
DVMT Graphics Memory
This feature allows the user to display the DVMT Graphics Memory settings.
Azalia Audio Controller
This option allows the user to enable or disable the onboard Azalia Audio Controller.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Select Auto to allow the HD Audio Controller to be automatically enabled when
detected by the BIOS. The options are Enable, Disabled and Auto.
Route Port 80h Cycles to
This feature allows the user to decide which bus to send debug information to. The
options are Disabled, PCI and LPC.
Memory Cache
Cache System BIOS Area
This setting allows you to designate a reserve area in the system memory to be used
as a System BIOS buffer and allow BIOS to write (cache) data into this reserved
memory area. Select Write Protect to enable this function, and this area will be
reserved for BIOS ROM access only. Select Uncached to disable this function and
make this area available for other devices.
Cache Video BIOS Area
This setting allows you to designate a reserve area in the system memory to be
used as a Video BIOS buffer and allow BIOS to write (cache) data into this reserved
memory area. Select Write Protect to enable the function and this area will be
reserved for Video BIOS ROM access only. Select Uncached to disable this function
and make this area available for other devices.
Cache Base 0-512K
If enabled, this feature will allow the data stored in the base memory area: block
0-512K to be cached (written) into a buffer, a storage area in the Static DROM
(SDROM) or to be written into L1, L2 cache inside the CPU to speed up CPU
operations. Select Uncached to disable this function. Select Write Through to allow
data to be cached into the buffer and written into the system memory at the
same time. Select Write Protect to prevent data from being written into the base
memory area of Block 0-512K. Select Write Back to allow the CPU to write data
back directly from the buffer without writing data to the System Memory for fast
CPU data processing and operation. The options are Uncached, Write Through,
Write Protect, and Write Back.
Cache Base 512K-640K
If enabled, this feature will allow the data stored in the memory area: 512K-640K
to be cached (written) into a buffer, a storage area in the Static DROM (SDROM)
or written into L1, L2, L3 cache inside the CPU to speed up CPU operations.
Select Uncached to disable this function. Select Write Through to allow data to
be cached into the buffer and written into the system memory at the same time.
Select Write Protect to prevent data from being written into the base memory
area of Block 512K-640K. Select Write Back to allow the CPU to write data back
directly from the buffer without writing data to the System Memory for fast CPU
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
data processing and operation. The options are Uncached, Write Through, Write
Protect, and Write Back.
Cache Extended Memory Area
If enabled, this feature will allow the data stored in the extended memory area to
be cached (written) into a buffer, a storage area in the Static DROM (SDROM) or
written into L1, L2, L3 cache inside the CPU to speed up CPU operations. Select
Uncached to disable this function. Select Write Through to allow data to be cached
into the buffer and written into the system memory at the same time. Select Write
Protect to prevent data from being written into the extended memory area above 1
MB. Select Write Back to allow the CPU to write data back directly from the buffer
withoutwritingdatatotheSystemMemoryforfastCPUdataprocessingandoperation.
The options are Uncached, Write Through, Write Protect, and Write Back.
Cache A000-AFFF
Cache B000-BFFF
Cache C800-CBFF
Cache CC00-CFFF
Cache D000-D3FF
Cache D400-D7FF
Cache D800-DBFF
Cache DC00-DFFF
Select Disabled to prevent the data stored in the memory block specified from being
cached into a cache area in the CPU or a buffer in the Static DROM. Select USWC
Caching to use the Uncached, Speculative and Write Combined Mode for the data
in the memory block specified. Select Write Through to allow the data stored in the
memory block specified to be cached into a CPU cache area and written into the
system memory at the same time. Select Write Protect to prevent data from being
written into the memory block specified. Select Write Back to allow the CPU to write
data back directly from the buffer to the memory block specified without writing data
to the System Memory for fast CPU data processing and operation. The options are
Disabled, USWC Caching, Write Through, Write Protect, and Write Back.
Cache E000-E3FF
Cache E400-E7FF
Cache E800-EBFF
Cache EC00-EFFF
Select Disabled to prevent the data stored in the memory block specified from being
cached into a cache area in the CPU or a buffer in the Static DROM. Select USWC
Caching to use the Uncached, Speculative and Write Combined Mode for the data
in the memory block specified. Select Write Through to allow the data stored in the
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
memory block specified to be cached into a CPU cache area and written into the
system memory at the same time. Select Write Protect to prevent data from being
written into the memory block specified. Select Write Back to allow the CPU to write
data back directly from the buffer to the memory block specified without writing data
to the System Memory for fast CPU data processing and operation. The options are
Disabled, USWC Caching, Write Through, Write Protect, and Write Back.
PNP Configuration
Access the submenu to make changes to the following settings for PNP (Play &
Plug) devices.
PCI Device Slot#1 - PCI Device Slot#4
Access the submenu for each of the settings above to make changes to the
following settings:
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
Latency Timer
This setting allows you to set the clock rate for the bus master. A high-priority,
high-throughout device may benefit from a greater clock rate. The options are
Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix,
Novelle and other Operating Systems, please select the option: other. If a drive
fails after the installation of a new software, you might want to change this setting
and try again. A different OS requires a different Bus master clock rate.
Onboard PCI IDE/Onboard LAN (PCI IDE: for C2SBA+II/C2SBA+
only)
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Latency Timer
This setting allows you to set the clock rate for the bus master. A high-priority,
high-throughout device may benefit from a greater clock rate. The options are
Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix,
Novelle and other Operating Systems, please select the option: other. If a drive
fails after the installation of a new software, you might want to change this setting
and try again. A different OS requires a different bus master clock rate.
IDE RAID Mode (Available on the Onboard PCI IDE Submenu.)
This feature allows you to set the IDE RAID Mode. The default setting is ATA/
ATAPI.
PCI-E x1 Slot
Access the submenu for each of the settings above to make changes to the
following:
PCI Express Port#1
Select Enabled to always enable PCI-Ex1 Port#1. Select Disabled to disable
PCI-Ex1 Port#1 and all other PCI-E ports. When set to Auto, PCI-Ex1 Port#1
will be enabled if a PCI add-on card is detected. The options are Auto, Enabled
and Disabled.
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
Latency Timer
This setting allows you to set the clock rate for the bus master. A high-priority,
high-throughout device may benefit from a greater clock rate. The options are
Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix,
Novelle and other Operating Systems, please select the option: other. If a drive
fails after the installation of a new software, you might want to change this setting
and try again. A different OS requires a different bus master clock rate.
PEG (PCI-Express Graphics) Port Submenu
Access the submenu for each of the settings above to make changes to the
following:
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
PCI-Express Graphics (PEG) Port (This submenu is for debugging
only.)
Select Auto to automatically enable the PCI-Express Graphics Port if a PCI
add-on card is detected. Select Disabled to always disable the PEG Port. Select
Enabled to always enable the PEG Port. (Debugging is enabled if a debug card
is detected.) The default setting is Auto.
When the PCI-Exp. Graphics Port is enabled, the following items will be
displayed:
PEG Port Enabled=
PEG Port Number=
PEG Width=
PEG Port Slot Number=
PEG Power Limit=
PEG Slot Card Detect=
PCI-Express x4 Slot
Access the submenu for each of the settings above to make changes to the
following:
PCI Express Port#5
Select Enabled to always enable PCI-Ex4 Port#5. Select Disabled to always
disable PCI-Ex4 Port#5. (If PCI-E x1 Port#1 is disabled, PCI-E x4 Port#5 will
be disabled as well). When set to Auto, PCI-Ex4 Port#5 will be enabled if a PCI
add-on card is detected. The options are Auto, Enabled and Disabled.
Option ROM Scan
When enabled, this setting will initialize the device expansion ROM. The options
are Enabled and Disabled.
Enable Master
This setting allows you to enable the selected device as the PCI bus master.
The options are Enabled and Disabled.
Latency Timer
This setting allows you to set the clock rate for the bus master. A high-priority,
high-throughout device may benefit from a greater clock rate. The options are
Default, 0020h, 0040h, 0060h, 0080h, 00A0h, 00C0h, and 00E0h. For Unix,
Novelle and other Operating Systems, please select the option: other. If a drive
fails after the installation of a new software, you might want to change this setting
and try again. A different OS requires a different bus master clock rate.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
I/O Device Configuration
Access the submenu to make changes to the following settings.
KBC Clock Input
This setting allows you to select the clock frequency for the Keyboard Controller.
The options are 6MHz, 8MHz, 12MHz, and 16MHz.
Serial Port A
This setting allows you to decide how the system controls Serial Port A. The options
are Enabled (user defined), Disabled, and Auto (BIOS- or OS- controlled).
Base I/O Address
This setting allows you to select the base I/O address for Serial Port A. The
options are 3F8, 2F8, 3E8, and 2E8.
Interrupt
This setting allows you to select the IRQ (interrupt request) for Serial Port A.
The options are IRQ3 and IRQ4.
Serial Port B
This setting allows you to decide how the system controls Serial Port B. The options
are Enabled (user defined), Disabled, Auto (BIOS controlled) and OS Controlled.
Mode
This setting allows you to set the type of device that will be connected to Serial
Port B. The options are Normal and IR (for an infrared device).
Base I/O Address
This setting allows you to select the base I/O address for Serial Port B. The
options are 3F8, 2F8, 3E8 and 2E8.
Interrupt
This setting allows you to select the IRQ (interrupt request) for Serial Port B.
The options are IRQ3 and IRQ4.
Parallel Port
This setting allows you to decide how the system controls the parallel port. The
options are Enabled (user defined), Disabled and Auto (BIOS-or OS- controlled).
Base I/O Address
Select the base I/O address for the parallel port. The options are 378, 278
and 3BC.
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Interrupt
This setting allows you to select the IRQ (interrupt request) for the parallel port.
The options are IRQ5 and IRQ7.
Mode
This feature allows you to specify the parallel port mode. The options are Output
only, Bi-Directional, EPP and ECP.
DMA Channel
This item allows you to specify the DMA channel for the parallel port. The
options are DMA1 and DMA3.
Floppy Disk Controller
This setting allows you to assign control of the floppy disk controller. The options
are Enabled (user defined), Disabled, and Auto (BIOS and OS controlled).
Hardware Monitoring
CPU Overheat Alarm
This option allows the user to select the CPU Overheat Alarm setting which de-
termines when the CPU OH alarm will be activated to provide warning of possible
CPU overheat.
Warning: Any temperature that exceeds the CPU threshold temperature predefined
by the CPU manufacturer may result in CPU overheat or system instability. When
the CPU temperature reaches this predefined threshold, the CPU and system cool-
ing fans will run at full speed.
The options are:
The Default Alarm Setting: Select this setting if you want the CPU overheat alarm
(including the LED and the buzzer) to be triggered when the CPU temperature
reaches about 5oC above the threshold temperature as predefined by the CPU
manufacturer to give the CPU and system fans additional time needed for CPU
and system cooling.
The Early Alarm Setting: Select this setting if you want the CPU overheat alarm
(including the LED and the buzzer) to be triggered as soon as the CPU temperature
reaches the CPU overheat threshold as predefined by the CPU manufacturer.
CPU1 Temperature
The CPU Temperature feature will display the CPU temperature status as detected
by the BIOS:
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Low – This level is considered as the ‘normal’ operating state. The CPU temperature
is well below the CPU ‘Temperature Tolerance’. The motherboard fans and CPU will
run normally as configured in the BIOS (Fan Speed Control).
User intervention: No action required.
Medium – The processor is running warmer. This is a ‘precautionary’ level and
generally means that there may be factors contributing to this condition, but the CPU
is still within its normal operating state and below the CPU ‘Temperature Tolerance’.
The motherboard fans and CPU will run normally as configured in the BIOS. The
fans may adjust to a faster speed depending on the Fan Speed Control settings.
User intervention: No action is required. However, consider checking the CPU
fans and the chassis ventilation for blockage.
High – The processor is running hot. This is a ‘caution’ level since the CPU’s ‘Tem-
perature Tolerance’ has been reached (or has been exceeded) and may activate
an overheat alarm:
The Default Alarm – the Overheat LED and system buzzer will activate if the High
condition continues for some time after it is reached. The CPU fan will run at full
speed to bring the CPU temperature down. If the CPU temperature still increases
even with the CPU fan running at full speed, the system buzzer will activate and
the Overheat LED will turn on.
The Early Alarm – the Overheat LED and system buzzer will be activated exactly
when the High level is reached. The CPU fan will run at full speed to bring the
CPU temperature down.
Note: In both the alarms above, please take immediate action as shown below.
See CPU Overheat Alarm to modify the above alarm settings.
User intervention: If the system buzzer and Overheat LED has activated, take
action immediately by checking the system fans, chassis ventilation and room
temperature to correct any problems. Note: the system may shut down if it con-
tinues for a long period to prevent damage to the CPU.
Notes: The CPU thermal technology that reports absolute temperatures
(Celsius/Fahrenheit) has been upgraded to a more advanced feature by
Intel in its newer processors. The basic concept is each CPU is embedded
by unique temperature information that the motherboard can read. This
‘Temperature Threshold’ or ‘Temperature Tolerance’ has been assigned
at the factory and is the baseline on which the motherboard takes action
during different CPU temperature conditions (i.e., by increasing CPU Fan
speed, triggering the Overheat Alarm, etc). Since CPUs can have different
‘Temperature Tolerances’, the installed CPU can now send information to
the motherboard what its ‘Temperature Tolerance’ is, and not the other way
around. This results in better CPU thermal management.
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Supermicro has leveraged this feature by assigning a temperature status to certain
thermal conditions in the processor (Low, Medium and High). This makes it easier
for the user to understand the CPU’s temperature status, rather than by just simply
seeing a temperature reading (i.e., 25oC).
The information provided above is for your reference only. For more information on
thermal management, please refer to Intel’s Web site at www.Intel.com.
System Temperature
This displays the system's absolute temperature reading (i.e., 27oC)
Fan1 - Fan 5
If the feature of Auto Fan Control is enabled, the BIOS will automatically display
the status of the fan as specified.
Fan Speed Control Modes
This feature allows the user to decide how the system controls the speeds of the
onboard fans. The CPU temperature and the fan speed are correlative. When
the CPU on-die temperature increases, the fan speed will also increase, and vice
versa. If the option is set to “4-pin”, the fan speed will be controlled by Pulse Width
Modulation (PWM). Select “Workstation” if your system is used as a Workstation.
Select “Disable” to disable the fan speed control function to allow the onboard
fans to constantly run at full speed (12V). The Options are: 1. Disable and 2.
Optimized for Workstations with 4-pin.
Note: In the Windows OS environment, the Supero Doctor III settings take prece-
dence over the BIOS settings. When first installed, Supero Doctor III adopts the
temperature threshold settings previously set in the BIOS. Any subsequent changes
to these thresholds must be made within Supero Doctor, since the SD III settings
override the BIOS settings. For the Windows OS to adopt the BIOS temperature
threshold settings, please change the SDIII settings to be the same as those set
in the BIOS.
Voltage Monitoring
The following items will be monitored and displayed:
Vcore A
12V
VDIMM
5V
+3.3V
-12V
3.3Vsb
Vbat
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
4-5
Security Settings
Choose Security from the Phoenix BIOS Setup Utility main menu with the arrow
keys. You should see the following display. Security setting options are displayed by
highlighting the setting using the arrow keys and pressing <Enter>. All Security BIOS
settings are described in this section.
Supervisor Password Is:
This item indicates if a supervisor password has been entered for the system. Clear
means such a password has not been used and Set means a supervisor password
has been entered for the system.
User Password Is:
This item indicates if a user password has been entered for the system. Clear
means such a password has not been used and Set means a user password has
been entered for the system.
Set Supervisor Password
When the item Set Supervisor Password is highlighted, hit the <Enter> key. When
prompted, type the Supervisor's password in the dialogue box to set or to change
supervisor's password, which allows access to the BIOS.
Set User Password
When the item Set User Password is highlighted, hit the <Enter> key. When
prompted, type the user's password in the dialogue box to set or to change the
user's password, which allows access to the system at boot-up.
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
Fixed Disk Boot Sector
Select Normal to enable the function of Write-Protect to protect the boot sector on
the hard drives against viruses.
Password on Boot
When this feature is set to Enabled, a password is required for a user to enter
the system at bootup. The options are Enabled (password required) and Disabled
(password not required).
TPM (Trusted Platform Modules) Support
Select Enabled to enable support for trusted platforms and allow the BIOS to
automatically download the drivers needed to provide support for the platforms
specified. The options are Enabled and Disabled.
If set to Enabled, the TPM State screen displays. (See the next section.)
4-23
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
4-6
TPM (Trusted Platform Modules) State
Choose the TPM State menu from the Phoenix BIOS Setup Utility with the arrow
keys. You should see the following display.
Current TPM State
This item shows the current TPM State only.
Change TPM State
Select "Enabled &Activate" to enableTPM support for the system. Select De-activate
& Disabled to disable the function of TPM support. If "No Change" is selected, no
changes will be done to the current TPM State. Select Clear to clear or erase all
information related to TPM support.
If set to "Clear", the sub-menu: Physical Presence Operations will appear. Select
Reject to cancel the selection. Select Execute to proceed with selection. All
information related to TPM Support will be erased.
4-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: BIOS
4-7
Boot Settings
Choose Boot from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. See details on how to change the order and
specs of boot devices in the Item Specific Help window. All Boot BIOS settings are
described in this section.
Boot List
Candidate
List
Boot Priority Order/Excluded from Boot Orders
The devices included in the boot list section (above) are bootable devices listed in
the sequence of boot order as specified. The boot functions for the devices included
in the candidate list (above) are currently disabled. Use a <+> key or a <-> key to
move the device up or down. Use the <f> key or the <r> key to specify the type of
an USB device, either fixed or removable. You can select one item from the boot
list and hit the <x> key to remove it from the list of bootable devices (to make its
resource available for other bootable devices). Subsequently, you can select an
item from the candidate list and hit the <x> key to remove it from the candidate
list and put it in the boot list. This item will then become a bootable device. See
details on how to change the priority of boot order of devices in the Item Specific
Help window.
4-25
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
4-8
Exit
Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys.
You should see the following display. All Exit BIOS settings are described in this
section.
Exit Saving Changes
Highlight this item and hit <Enter> to save any changes you made and to exit the
BIOS Setup utility.
Exit Discarding Changes
Highlight this item and hit <Enter> to exit the BIOS Setup utility without saving any
changes you may have made.
Load Setup Defaults
Highlight this item and hit <Enter> to load the default settings for all items in the
BIOS Setup. These are the safest settings to use.
Discard Changes
Highlight this item and hit <Enter> to discard (cancel) any changes you made.
You will remain in the Setup utility.
Save Changes
Highlight this item and hit <Enter> to save any changes you made. You will remain
in the Setup utility.
4-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: BIOS POST Messages
Appendix A
BIOS POST Messages
During the Power-On Self-Test (POST), the BIOS will check for problems. If a prob-
lem is found, the BIOS will activate an alarm or display a message. The following is
a list of such BIOS messages.
Failure Fixed Disk
Fixed disk is not working or not configured properly. Check to see if fixed disk is at-
tached properly. Run Setup. Find out if the fixed-disk type is correctly identified.
Stuck key
Stuck key on keyboard.
Keyboard error
Keyboard not working.
Keyboard Controller Failed
Keyboard controller failed test. May require replacing keyboard controller.
Keyboard locked - Unlock key switch
Unlock the system to proceed.
Monitor type does not match CMOS - Run SETUP
Monitor type not correctly identified in Setup
Shadow Ram Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was de-
tected.
System RAM Failed at offset: nnnn
System RAM failed at offset nnnn of in the 64k block at which the error was de-
tected.
Extended RAM Failed at offset: nnnn Extended memory not working or not con-
figured properly at offset nnnn.
System battery is dead - Replace and run SETUP
The CMOS clock battery indicator shows the battery is dead. Replace the battery and
run Setup to reconfigure the system.
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
System CMOS checksum bad - Default configuration used
System CMOS has been corrupted or modified incorrectly, perhaps by an application
program that changes data stored in CMOS. The BIOS installed Default Setup Values.
If you do not want these values, enter Setup and enter your own values. If the error
persists, check the system battery or contact your dealer.
System timer error
The timer test failed. Requires repair of system board.
Real time clock error
Real-Time Clock fails BIOS hardware test. May require board repair.
Check date and time settings
BIOS found date or time out of range and reset the Real-Time Clock. May require
setting legal date (1991-2099).
Previous boot incomplete - Default configuration used
Previous POST did not complete successfully. POST loads default values and offers
to run Setup. If the failure was caused by incorrect values and they are not corrected,
the next boot will likely fail. On systems with control of wait states, improper Setup
settings can also terminate POST and cause this error on the next boot. Run Setup
and verify that the waitstate configuration is correct. This error is cleared the next
time the system is booted.
Memory Size found by POST differed from CMOS
Memory size found by POST differed from CMOS.
Diskette drive A error
Diskette drive B error
Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that
the drive is defined with the proper diskette type in Setup and that the diskette drive
is attached correctly.
Incorrect Drive A type - run SETUP
Type of floppy drive A: not correctly identified in Setup.
Incorrect Drive B type - run SETUP
Type of floppy drive B: not correctly identified in Setup.
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: BIOS POST Messages
System cache error - Cache disabled
RAM cache failed and BIOS disabled the cache. On older boards, check the cache
jumpers. You may have to replace the cache. See your dealer.Adisabled cache slows
system performance considerably.
CPU ID:
CPU socket number for Multi-Processor error.
EISA CMOS not writeable
ServerBIOS2 test error: Cannot write to EISA CMOS.
DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory
Access) registers.
Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
Fail-Safe Timer NMI Failed
ServerBIOS2 test error: Fail-Safe Timer takes too long.
Device Address Conflict
Address conflict for specified device.
Allocation Error for: device
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified
device.
CD ROM Drive
CD ROM Drive identified.
Entering SETUP ...
Starting Setup program
Failing Bits: nnnn
ThehexnumbernnnnisamapofthebitsattheRAMaddresswhichfailedthememory
test. Each 1 (one) in the map indicates a failed bit. See errors 230, 231, or 232 above
for offset address of the failure in System, Extended, or Shadow memory.
Fixed Disk n
Fixed disk n (0-3) identified.
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Invalid System Configuration Data
Problem with NVRAM (CMOS) data.
I/O device IRQ conflict
I/O device IRQ conflict error.
PS/2 Mouse Boot Summary Screen:
PS/2 Mouse installed.
nnnn kB Extended RAM Passed
Where nnnn is the amount of RAM in kilobytes successfully tested.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes successfully tested.
nnnn kB Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes successfully tested.
nnnn kB System RAM Passed
Where nnnn is the amount of system RAM in kilobytes successfully tested.
One or more I2O Block Storage Devices were excluded from the Setup Boot
Menu
There was not enough room in the IPL table to display all installed I2O block-storage
devices.
Operating system not found
Operating system cannot be located on either drive A: or drive C:. Enter Setup and
see if fixed disk and drive A: are properly identified.
Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to locate the address and display
it on the screen. If it cannot locate the address, it displays ????. Parity is a method
for checking errors in binary data. A parity error indicates that some data has been
corrupted.
Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it
on the screen. If it cannot locate the address, it displays ????.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: BIOS POST Messages
Press <F1> to resume, <F2> to Setup, <F3> for previous
Displayed after any recoverable error message. Press <F1> to start the boot process
or <F2> to enter Setup and change the settings. Press <F3> to display the previous
screen (usually an initialization error of an Option ROM, i.e., an add-on card). Write
down and follow the information shown on the screen.
Press <F2> to enter Setup
Optional message displayed during POST. Can be turned off in Setup.
PS/2 Mouse:
PS/2 mouse identified.
Run the I2O Configuration Utility
One or more unclaimed block storage devices have the Configuration Request bit set
in the LCT. Run an I2O Configuration Utility (e.g. the SAC utility).
System BIOS shadowed
System BIOS copied to shadow RAM.
UMB upper limit segment address: nnnn
Displays the address nnnn of the upper limit of Upper Memory Blocks, indicating
released segments of the BIOS which can be reclaimed by a virtual memory man-
ager.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Notes
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
Appendix B
BIOS POST Codes
This section lists the POST (Power On Self Test) codes for the Phoenix BIOS. POST
codes are divided into two categories: recoverable and terminal.
Recoverable POST Errors
When a recoverable type of error occurs during POST, the BIOS will display an
POST code that describes the problem. BIOS may also issue one of the follow-
ing beep codes:
1 long and two short beeps - video configuration error
1 repetitive long beep - no memory detected
1 continuous beep w/ Front Panel Overheat LED on - system overheat
Terminal POST Errors
If a terminal type of error occurs, BIOS will shut down the system. Before doing
so, BIOS will write the error to port 80h, attempt to initialize video and write the
error in the top left corner of the screen. The following is a list of codes that may
be written to port 80h.
POST Code Description
02h
03h
04h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
12h
13h
14h
16h
17h
Verify Real Mode
Disable Non-Maskable Interrupt (NMI)
Get CPU type
Initialize system hardware
Disable shadow and execute code from the ROM.
Initialize chipset with initial POST values
Set IN POST flag
Initialize CPU registers
Enable CPU cache
Initialize caches to initial POST values
Initialize I/O component
Initialize the local bus IDE
Initialize Power Management
Load alternate registers with initial POST values
Restore CPU control word during warm boot
Reset PCI Bus Mastering devices
Initialize keyboard controller
1-2-2-3 BIOS ROM checksum
Initialize cache before memory Auto size
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
POST Code Description
18h
1Ah
1Ch
20h
22h
24h
28h
29h
2Ah
2Ch
2Eh
8254 timer initialization
8237 DMA controller initialization
Reset Programmable Interrupt Controller
1-3-1-1 Test DRAM refresh
1-3-1-3 Test 8742 Keyboard Controller
Set ES segment register to 4 GB
Auto size DRAM
Initialize POST Memory Manager
Clear 512 kB base RAM
1-3-4-1 RAM failure on address line xxxx
1-3-4-3 RAM failure on data bits xxxx of low byte of
memory bus
2Fh
32h
33h
36h
38h
3Ah
3Ch
3Dh
41h
42h
45h
46h
48h
49h
4Ah
4Bh
4Ch
4Eh
4Fh
50h
51h
52h
54h
55h
58h
59h
5Ah
5Bh
Enable cache before system BIOS shadow
Test CPU bus-clock frequency
Initialize Phoenix Dispatch Manager
Warm start shut down
Shadow system BIOS ROM
Auto size cache
Advanced configuration of chipset registers
Load alternate registers with CMOS values
Initialize extended memory for RomPilot (optional)
Initialize interrupt vectors
POST device initialization
2-1-2-3 Check ROM copyright notice
Check video configuration against CMOS
Initialize PCI bus and devices
Initialize all video adapters in system
QuietBoot start (optional)
Shadow video BIOS ROM
Display BIOS copyright notice
Initialize MultiBoot
Display CPU type and speed
Initialize EISA board (optional)
Test keyboard
Set key click if enabled
Enable USB devices
2-2-3-1 Test for unexpected interrupts
Initialize POST display service
Display prompt “Press <ESC> to enter SETUP”
Disable CPU cache
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
POST Code Description
5Ch
60h
62h
64h
66h
67h
68h
69h
6Ah
6Bh
6Ch
70h
72h
76h
7Ch
7Dh
7Eh
80h
81h
82h
83h
84h
85h
86h
87h
Test RAM between 512 and 640 kB
Test extended memory
Test extended memory address lines
Jump to UserPatch1
Configure advanced cache registers
Initialize Multi Processor APIC
Enable external and CPU caches
Setup System Management Mode (SMM) area
Display external L2 cache size
Load custom defaults (optional)
Display shadow-area message
Display error messages
Check for configuration errors
Check for keyboard errors
Set up hardware interrupt vectors
Initialize Intelligent System Monitoring (optional)
Initialize coprocessor if present
Disable onboard Super I/O ports and IRQs (optional)
Late POST device initialization
Detect and install external RS232 ports
Configure non-MCD IDE controllers
Detect and install external parallel ports
Initialize PC-compatible PnP ISA devices
Re-initialize onboard I/O ports.
Configure Motherboard Configurable Devices
(optional)
88h
89h
8Ah
8Bh
8Ch
8Fh
90h
91h
92h
93h
95h
96h
97h
98h
Initialize BIOS Data Area
Enable Non-Maskable Interrupts (NMIs)
Initialize Extended BIOS Data Area
Test and initialize PS/2 mouse
Initialize floppy controller
Determine number of ATA drives (optional)
Initialize hard-disk controllers
Initialize local-bus hard-disk controllers
Jump to UserPatch2
Build MPTABLE for multi-processor boards
Install CD ROM for boot
Clear huge ES segment register
Fix up Multi Processor table
1-2 Search for option ROMs and shadow if successful. One
long, two short beeps on checksum failure
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
POST Code Description
99h
9Ch
9Dh
9Eh
9Fh
A0h
A2h
A4h
A8h
AAh
ACh
AEh
B0h
B1h
B2h
B4h
B5h
B6h
B7h
B9h
BAh
BCh
BDh
BEh
BFh
C0h
C1h
C2h
C3h
C4h
C6h
C7h
C8h
C9h
CDh
Check for SMART Drive (optional)
Set up Power Management
Initialize security engine (optional)
Enable hardware interrupts
Determine number of ATA and SCSI drives
Set time of day
Check key lock
Initialize typematic rate
Erase <ESC> prompt
Scan for <ESC> key stroke
Enter SETUP
Clear Boot flag
Check for errors
Inform RomPilot about the end of POST (optional)
POST done - prepare to boot operating system
1 One short beep before boot
Terminate QuietBoot (optional)
Check password (optional)
Initialize ACPI BIOS and PPM Structures
Prepare Boot
Initialize SMBIOS
Clear parity checkers
Display MultiBoot menu
Clear screen (optional)
Check virus and backup reminders
Try to boot with INT 19
Initialize POST Error Manager (PEM)
Initialize error logging
Initialize error display function
Initialize system error flags
Console redirection init.
Unhook INT 10h if console redirection enabled
Force check (optional)
Extended ROM checksum (optional)
Reclaim console redirection vector
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: BIOS POST Codes
POST Code Description
D2h
D4h
D8h
DEh
Unknown interrupt
Check Intel Branding string
Alert Standard Format initialization
Log error if micro-code not updated properly
The following are for boot block in Flash ROM
POST Code Description
E0h
E1h
E2h
E3h
E4h
E5h
E6h
E7h
E8h
E9h
EAh
EBh
ECh
EDh
EEh
EFh
F0h
F1h
F2h
F3h
F4h
F5h
F6h
F7h
Initialize the chipset
Initialize the bridge
Initialize the CPU
Initialize system timer
Initialize system I/O
Check force recovery boot
Checksum BIOS ROM
Go to BIOS
Set Huge Segment
Initialize Multi Processor
Initialize OEM special code
Initialize PIC and DMA
Initialize Memory type
Initialize Memory size
Shadow Boot Block
System memory test
Initialize interrupt vectors
Initialize Run Time Clock
Initialize video
Initialize System Management Manager
Output one beep
Clear Huge Segment
Boot to Mini DOS
Boot to Full DOS
If the BIOS detects errors on 2C, 2E, or 30 (base 512K RAM error), it displays an
additional word-bitmap (xxxx) indicating the address line or bits that have failed. For
example, “2C 0002” means address line 1 (bit one set) has failed. “2E 1020" means
data bits 12 and 5 (bits 12 and 5 set) have failed in the lower 16 bits. The BIOS also
sends the bitmap to the port-80 LED display. It first displays the checkpoint code,
followed by a delay, the high-order byte, another delay, and then the low-order byte
of the error. It repeats this sequence continuously.
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Notes
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
Appendix C
Intel HostRAID Setup Guidelines
(For the C2SBA+II Only)
After all the hardware has been installed, you must first configure SATA HostRAID
or SAS HostRAID before you install the Windows Operating System and other
software drivers.
Important Notes to the User:
Note 1: This chapter describes RAID Configuration Instructions for the Intel ICH9R
Host RAID Controller designed for the Windows OS.
Note 2: If you do not wish to configure onboard SATA or SAS RAID functions,
please go directly to Section C-2 and Appendix D for the operating system & other
software installation instructions.
C-1
Introduction to Serial ATA and Parallel ATA
To configure the SATA RAID functions, you must first use the Intel ICH9R SATA
RAID Utility program to configure the RAID Level that you desire before installing
the Windows XP/2003 operating system and other software drivers. (The necessary
drivers are all included on the Super Micro CD that came packaged with your
motherboard.) Note: the current version of the ICH9R SATA RAID Utility can only
support Windows XP/2003 Operating Systems.
Serial ATA (SATA)
Serial ATA (SATA) is a physical storage interface that uses a single cable with a
minimum of four wires to create a point-to-point connection between devices. It
is a serial link, which supports transfer rates up to 3.0 Gbps. Because the serial
cables used in SATA are thinner than the traditional cables used in Parallel ATA
(PATA), SATA systems have better airflow and can be installed in smaller chassis.
In addition, the cables used in PATA are limited to a length of 40cm, while Serial
ATA cables can be up to one meter in length. Overall, SATA provides better func-
tionality than PATA.
Introduction to the Intel ICH9R Serial RAID
Located in the South Bridge of the G33 chipset, the I/O Controller Hub (ICH9R)
provides the I/O subsystem with access to the rest of the system. It supports 1-
channel UltraATA/100 Bus Master IDE controller (PATA) and six Serial ATA (SATA)
ports. The ICH9R supports the following PATA and SATA device configurations:
Legacy mode and Native mode.
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Intel HostRAID Configurations
The following types of Intel's HostRAID configurations are supported:
RAID 0 (Data Striping): this writes data in parallel, interleaved ("striped") sections
of two hard drives. Data transfer rate is doubled over using a single disk.
RAID1 (Data Mirroring): an identical data image from one drive is copied to another
drive. The second drive must be the same size or larger than the first drive.
RAID 10 (Striping & Mirroring): RAID 0 and 1 schemes are combined (without parity
information) to get the benefits of both.
RAID 5: both data and parity information are striped and mirrored across three or
more hard drives.
Intel Matrix Storage
The Intel Matrix Storage, supported by the ICH9R, allows the user to create RAID
0, RAID 1, RAID 10 and RAID 5 sets by using only six identical hard disk drives.
The Intel Matrix Storage Technology creates two partitions on each hard disk drive
and generate a virtual RAID 0, RAID 1, RAID 10 and RAID 5 sets. It also allows
you the change the HDD partition size without any data.
Configuring BIOS settings for SATA RAID Functions (in the Native
Mode)
1. Press the <Del> key during system bootup to enter the BIOS Setup Utility.
Note: If it is the first time powering on the system, we recommend you load the
Optimized Default Settings. If you have already done so, please skip to Step 3.
2. Use the arrow keys to select the "Exit" Settings. Once in the "Exit" settings,
Scroll down to select "Load Optimized Default Settings" and press the <Enter>
key. Select "OK" to confirm the selection. Press the <Enter> key to load the default
settings for the BIOS.
3. Use the arrow keys to select the "Main" section in BIOS.
4. Scroll down to "SATA RAID Enabled" and press <Enter>. Then, select "En-
abled."
5. Scroll down to "Exit". Select "Save and Exit" from the "Exit" menu. Press the
<Enter> key to save the changes and exit the BIOS.
6. Once you've exited the BIOS Utility, the system will re-boot.
7. During the system boot-up, press the <Ctrl> and <I> keys simultaneously to run
the Intel RAID Configuration Utility when prompted by the following message: Press
<Ctrl> <I> for the Intel RAID Configuration Utility.
(Note: The Intel RAID Configuration Utility is only available for systems with two
or more drives installed. The Intel RAID Utility screen will not display in systems
with one drive installed.)
C-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
Using the Intel ICH9R SATA RAID Utility Program
1. Creating, Deleting and Resetting RAID Volumes:
a. After the system exits from the BIOS Setup Utility, the system will automatically
reboot. The following screen appears after Power-On Self Test.
b. When you see the above screen, press the <Ctrl> and the <I> keys simultane-
ously to access the main menu of the SATA RAID Utility.
c. Use the Up and Down arrow keys to select Create RAID Volume, Delete RAID
Volume, Reset Disks to Non-RAID or Exit.
Note: All graphics and screen shots shown in the manual are for reference only. The
screen shots shown in the manual do not imply Super Micro's endorsement or non-en-
dorsement on any 3rd party's product. Your screens may or many not look exactly the
same as the graphics shown in this manual.
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Creating a RAID 0 Volume:
a. Select "Create RAID Volume" from the main menu and press the <Enter> key.
The following screen will appear:
b. Specify a name for the RAID 0 set and press the <Tab> key or the <Enter> key
to go to the next field. (You can use the <Esc> key to select the previous menu.)
c. When RAID Level item is highlighted, press the <Up Arrow>, <Down Arrow> keys
to select RAID 0 (Stripe) and hit <Enter>.
d. When the Select Disks item is highlighted, press <Enter> to select the HDD to
configure as RAID. The following pop-up screen displays: (See the note on Page
C-3)
e. Use the <Up Arrow>, <Down Arrow> keys to highlight a drive and press <Space>
to select it. A triangle appears to confirm the selection of the drive. When all RAID
drives for this volume have been selected, hit <Enter>.
f. Use the <Up Arrow>, <Down Arrow> keys to select the stripe size, ranging from
4 KB to 128 KB for the RAID 0 array, and hit <Enter>. (Note: For a server, please
use a lower stripe size, and for a multimedia system, use a higher stripe size. The
default stripe size is 128 KB.)
g. Press <Enter> when the Create Volume item is highlighted. A warning message
displays.
h. When asked "Are you sure you want to create this volume (Y/N), press "Y" to
create the RAID volume, or type "N" to go back to the Create Volume menu.
C-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
Creating a RAID 1 Volume:
a. Select "Create RAID Volume" from the main menu and press the <Enter> key.
The following screen will appear:
b. Specify a name for the RAID 1 set and press the <Tab> key or the <Enter> key
to go to the next field. (You can use the <Esc> key to select the previous menu.)
c. When RAID Level item is highlighted, press the <Up Arrow>, <Down Arrow> keys
to select RAID 1 (Mirror) and hit <Enter>.
d. When Select Disks Item is height lighted, press <Enter> to select the HDD to
configure as RAID. The following pop-up screen displays: (See the note on Page
C-3)
e. Use the <Up Arrow>, <Down Arrow> keys to highlight a drive and press <Space>
to select it. A triangle appears to confirm the selection of the drive. When all RAID
drives for this volume have been selected, hit <Enter>.
f. When the Capacity item is highlighted, enter your RAID volume capacity and hit
<Enter>. The default setting is the maximum capacity allowed.
g. Press <Enter> when the Create Volume item is highlighted. A warning message
displays.
h. When asked "Are you sure you want to create this volume (Y/N), press "Y" to
create the RAID volume, or type "N" to go back to the Create Volume menu.
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Creating a RAID 10 (RAID 1+ RAID 0):
a. Select "Create RAID Volume" from the main menu and press the <Enter> key.
The following screen will appear:
b. Specify a name for the RAID 10 set and press <Enter>.
c. When RAID Level item is highlighted, use the <Up Arrow>, <Down Arrow> keys
to select RAID 10 (RAID1 + RAID0) and hit <Enter>.
d. When Select Disks Item is height lighted, press <Enter> to select the HDD to
configure as RAID. The following pop-up screen displays: (See the note on Page
C-3)
e. Use the <Up Arrow>, <Down Arrow> keys to highlight a drive and press <Space>
to select it. A triangle appears to confirm the selection of the drive. When all RAID
drives for this volume have been selected, hit <Enter>.
f. When the Stripe Size is highlighted, use the <Up Arrow>, <Down Arrow> keys to
select the stripe size from 4 KB to 128 KB for your RAID 10 and hit <Enter>. The
default setting is 64 KB. (Note: For a server, please use a lower stripe size, and
for a multimedia system, use a higher stripe size.)
g. When the RAID Volume Capacity item is highlighted, enter your RAID volume
capacity and hit <Enter>. The default setting is the maximum capacity allowed.
h. Press <Enter> when the Create Volume item is highlighted. A warning message
displays.
i. When asked "Are you sure you want to create this volume (Y/N), press "Y" to
create the RAID volume, or type "N" to go back to the Create Volume menu.
C-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
Creating a RAID 5 Set (Parity):
a. Select "Create RAID Volume" from the main menu and press the <Enter> key.
The following screen will appear:
b. Specify a name for the RAID 5 set and press <Enter>.
c. When the Raid Level is highlighted, use the <Up Arrow>, <Down Arrow> keys to
select RAID 5 (Parity) and hit <Enter>.
d. When the Disk item is highlighted, press <Enter> to select the HDD to configure
as RAID. The following pop-up screen displays: (See the note on Page C-3)
e. Use the <Up Arrow>, <Down Arrow> keys to highlight a drive and press <Space>
to select it. A triangle appears to confirm the selection of the drive. When all RAID
drives for this volume have been selected, hit <Enter>.
f. Use the <Up Arrow>, <Down Arrow> keys to select the stripe size, ranging from
4 KB to 128 KB for the RAID 5 array, and hit <Enter>. (Note: For a server, please
use a lower stripe size, and for a multimedia system, use a higher stripe size. The
default stripe size is 128 KB.)
g. Enter your desired RAID volume capacity and press <Enter> when the capacity
item is highlighted. The default setting is the maximum capacity allowed.
h
Press Enter when the Create Volume item is highlighted. A warning message
displays.
i. When asked "Are you sure you want to create this volume (Y/N), press "Y" to
create the RAID volume, or type "N" to go back to the Create Volume menu.
C-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Deleting a RAID Volume:
(Warning: Be sure to back up your data before deleting a RAID set.
You will lose all data on the disk drives when deleting a RAID set.)
a. From the main menu, select item2-Delete RAID Volume, and press <Enter>.
b. Use the <Up Arrow>, <Down Arrow> keys to select the RAID set you want to
delete and press <Del>. A Warning message displays.
c. When asked "Are you sure you want to delete this volume (Y/N), press "Y" to
delete the RAID volume, or type "N" to go back to the Delete Volume menu.
C-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
Resetting to Non-RAID and Resetting a RAID HDD
(Warning: Be cautious when you reset a RAID volume HDD to non-
RAID or Resetting a RAID HDD. Resetting a RAID volume HDD or
Resetting a RAID HDD will reformat the HDD and delete the internal
RAID structure on the drive.)
a. From the main menu, select item3-Reset Disks to Non- RAID, and press <Enter>.
The following screen will appear:
b. Use the <Up Arrow>, <Down Arrow> keys to highlight the RAID set drive to reset
and press <Space> to select. (For this feature to work properly, you must select all
drives within a RAID volume.)
c. Press <Enter> to reset the RAID set drive. A Warning message displays.
d. Press "Y" to reset the drive, or type "N" to go back to the main menu.
Exiting the Intel Matrix Storage Manager Utility:
a. From the main menu, select item4-Exit, and press <Enter>. A warning message
will appear.
b. Press "Y" to reset the drive, or type "N" to go back to the main menu.
C-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
C-2
Installing the Windows XP/2003 OS for Systems
with RAID Functions (For C2SBA+II only)
Note 1. Your motherboard may come with the ITE-8212 IDE Controller chip or the
ITE-8211 Controller chip. For proper OS installation, please obtain your ITE IDE
Controller model and other driver information before starting the OS installation. To
obtain your ITE Controller model# or other driver information, you can either reboot
the system and obtain your controller/driver Information displayed on the Option
ROM screen at bootup or identify your ITE IDE Controller and other controller chips
(if available) on the motherboard by referring to the board layout on Page 1-4 in
Chapter 1. Note 2. The Intel ICH9R SATA RAID does not support the Windows
2000.
1. Insert Microsoft's Windows XP/2003 Setup CD in the CD Driver, and the
system will start booting up from CD. (See Note 1 above.)
2. Press the <F6> key when the message-" Press F6 if you need to install a
third party SCSI or RAID driver" displays.
3. When the Windows XP/2003 Setup screen appears, press "S" to specify ad-
ditional device(s).
4. Insert the Driver Diskette-"ITE 8212 ATA RAID Controller for Windows" or the
Driver Diskette-"ITE 8211 ATA ATAPI Controller for Windows" into Drive A:
and press <Enter>. (See Note 1 above.)
5. When the Windows XP/2003 Setup screen appears, press "S" to specify ad-
ditional device(s).
6. Insert the driver diskette-"Intel AA RAID XP/2003 Driver for ICH9R" into Drive
A: and press the <Enter> key.
7. Choose the Intel(R) ICH9R SATA RAID Controller from the list indicated in
the XP/2003 Setup Screen, and press the <Enter> key.
8. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do it at this time.) Once all
devices are specified, press the <Enter> key to continue with the installation.
9. From the Windows XP/2003 Setup screen, press the <Enter> key. The
XP/2003 Setup will automatically load all device files and then, continue the
Windows XP/2003 installation.
10. After the Windows XP/2003 OS Installation is completed, the system will auto-
matically reboot.
C-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel HostRAID Setup Guidelines
C-3
Installing the Windows XP/2000/2003 OS for
Systems without RAID Functions
1. Insert Microsoft's Windows XP/2000/2003 Setup CD in the CD Driver, and the
system will start booting up from CD.
2. Press the <F6> key when the message-" Press F6 if you need to install a
third party SCSI or RAID driver" displays.
3. When the Windows XP/2000/2003 Setup screen appears, press "S" to specify
additional device(s).
4. Insert the driver diskette-"ITE RAID XP/2000/2003 Driver for IDE" into Drive
A: and press the <Enter> key.
5. Press the <Enter> key to proceed with the installation process. (If you need
to specify any additional devices to be installed, do it at this time.) Once all
devices are specified, press the <Enter> key to continue with the installation.
6. From the Windows XP/2000/2003 Setup screen, press the <Enter> key. The
XP/2000/2003 Setup will automatically load all device files and then continue
with the Windows XP/2000/2003 installation.
7. After the Windows XP/2000/2003 OS Installation is completed, the system will
automatically reboot.
8. Insert the Supermicro Setup CD that came with your motherboard into the CD
Drive during system boot, and the main screen will display.
C-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Notes
C-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Appendix D
Adaptec HostRAID Setup Guidelines
(For the C2SBA+II Only)
After all the hardware has been installed, you must first configure the Adaptec
Embedded Serial ATA RAID before you install the Windows operating system.
The necessary drivers are all included on the Supermicro bootable CDs that came
packagedwithyourmotherboard. Note1:Thefollowingsectionprovidesinformation
on the Adaptec SATA RAID Driver based on the Intel ICH9R Controller.
D-1
IntroductiontotheAdaptecEmbeddedSATARAID
Controller Driver
Serial ATA (SATA)
Serial ATA(SATA) is a physical storage interface. It uses a single cable with a
minimum of four wires to create a point-to-point connection between devices. It
is a serial link which supports SATA Transfer rates up to 3.0 Gbps. Because the
serial cables used in SATA are thinner than the traditional cables used in Paral-
lel ATA(PATA), SATA systems have better airflow and can be installed in smaller
chassis than Parallel ATA. In addition, the cables used in PATA can only extend
to 40cm long, while Serial ATA cables can extend up to one meter. Overall, Serial
ATA provides better functionality than Parallel ATA.
Introduction to the Intel ICH9R Controller Hub
Located in the South Bridge of the Intel G33 Chipset, the ICH9R Controller Hub
provides the I/O subsystem with access to the rest of the system. It supports the
Adaptec's firmware, which support up to six Serial ATA drives, up to two RAID
volumes and up to six drives in RAID Configurations.
* Adaptec’s SATA HostRAID Controller Firmware supports:
Four
Number of RAID Volumes supported Two
Total Drives in RAID Configurations Four
Drives supported
Examples of Valid RAID Configurations:
Two drives of RAID 1 + two drives of RAID 0
Two drives of RAID 1 + two drives of RAID 1
Three drives of RAID 0
Four drives of RAID 0
Examples of Invalid RAID Configurations:
Three drives of RAID 0 + two drives of RAID 1
(*Note: this table is applicable to Adaptec’s HostRAID Controller
Firmware only.)
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
To configure the Adaptec SATA RAID for Operating Systems that
support RAID functions(--Windows, Red Hat & SuSe, Linux)
1. Press the <Del> key during system bootup to enter the BIOS Setup Utility.
Note: If it is the first time powering on the system, we recommend you load the
Optimized Default Settings. If you have already done so, please skip to Step 3.
2. Use the arrow keys to select the "Exit" Settings. Once in the "Exit" settings,
Scroll down to select "Load Optimized Default Settings" and press the <Enter>
key. Select "OK" to confirm the selection. Press the <Enter> key to load the default
settings for the BIOS.
3. Use the arrow keys to select the "Main" section in BIOS.
4. Scroll down to "SATA Control Mode" and press the <Enter> key to select
"Enhanced"
5. Scroll down to "SATA RAID Enabled" and press <Enter>. Then, select "En-
abled."
6. Scroll down to "ICH RAID Codebase" and select "Adaptec". Then press <En-
ter>. (For ICH RAID Codebase: Change the setting from Intel to Adaptec.)
7. Scroll down to "Exit". Select "Exit Saving Changes" from the "Exit" menu. Press
the <Enter> key to save the changes and exit the BIOS.
8. Once you've exited the BIOS Utility, the system will re-boot.
9. During the system boot-up, press the <Ctrl> and <A> keys simultaneously to
run the Intel RAID Configuration Utility when prompted by the following message:
Press <Ctrl> <A> for Intel RAID Configuration Utility.
D-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
The Adaptec Embedded Serial ATA with HostRAID Controller
Driver
The Adaptec Embedded Serial ATA RAID Controller adds SATA/RAID functional-
ity and performance enhancements to a motherboard. RAID striping (RAID 0)
allows data to be written across multiple drives, greatly improving hard disk I/O
performance. RAID mirroring (RAID 1) allows data to be simultaneously written
to two drives, improving data security even if a single hard disk fails. A Stripe of
Mirrors (RAID 10) provides multiple RAID 1 mirrors and a RAID 0 stripe, maximiz-
ing data security and system efficiency. By incorporating the Adaptec Embedded
Serial ATA into the motherboard design, Supermicro's C2SBA+II offers the user
the benefits of SATARAID without the high costs associated with hardware RAID
applications.
Using the Adaptec RAID Configuration Utility (ARC)
The Adaptec RAID Configuration Utility, an embedded BIOS Utility, includes the
following:
Array Configuration Utility: Use this utility to create, configure and manage ar-
rays.
Disk Utilities: Use this option to format or verify disks.
To run the Adaptec RAID Configuration Utility, you will need to do the following:
1. Enable RAID functions in the system BIOS. (Refer to Chapter 4 for System
BIOS Configurations).
2. Press the <Ctrl> and <A> keys simultaneously when prompted to do so during
system boot. (Refer to the previous page for detailed instructions.)
A. Using the Array Configuration Utility (ACU)
When you press <Ctrl> and <A> keys simultaneously at the prompt during system
bootup, the main menu will appear.
Note: To select an option, use the arrow keys to highlight the item and then press
the <Enter> key to select it. To return to the previous menu, press the <ESC> key.
Press the <Insert> key to select a drive. When a drive is highlighted (selected),
press the <Delete> key to de-select it.
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Managing Arrays
Select this option to view array properties, and configure array settings.
To select this option, using the arrow keys and the <enter> key, select "Managing
Arrays" from the main menu as shown above.
D-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Configuring Disk Drives
You may need to configure a disk drive before you can use it.
Caution: Configuring a disk may overwrite the partition table on the disk and may
make any data on the disk inaccessible. If the drive is used in an array, you may
not be able to use the array again.
Do not configure a disk that is part of a boot array. To determine which disks are
associated with a particular array, please refer to Viewing Array Properties.
To configure a disk drive:
1. From the main menu (shown on Page D-4), select Configure Drives and hit
<Enter> (as shown below.)
D-5
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
2. From the "Select Drives for Configuring" List (shown below,) select the drives
you want to configure and press <Insert>.
3. The drive you've selected will appear in the "Selected Drives Dialog Box" on
the right (as shown below.) Repeat the same steps until all drives that you want
to configure appear in the selected drives box.
4. Once both drives display in the selected drive box, press <Enter.>
D-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
5. Read the warning message as shown in the screen below.
6. Make sure that you have selected the correct disk drives to configure. If correct,
type Y to continue.
D-7
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Creating Arrays
Before you create arrays, make sure that the disks for the array are connected
and installed in your system. Note that disks with no usable space, or disks that
are un-initialized or not formatted are shown in gray and cannot be used. Note: It
is recommended that you configure devices before you create arrays.
To create an array:
1. From the main menu (shown on page D-4), select Create Array.
2. Select the disks for the new array and press Insert (as the screen shown below).
Note: To de-select any disk, highlight the disk and press Delete.
3. The arrays you have selected will appear on the Selected Drives dialog box on
the right (as shown below.)
4 Press Enter when both disks for the new array are selected. The Array Proper-
ties menu displays.
D-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Assigning Array Properties
Once a new array is completed, you can assign properties to the array.
Caution: Once the array is created and its properties are assigned, and you can-
not change the array properties using this utility.
To assign properties to the new array:
1. In the Array Properties menu (as shown in the screen below), select an array
type and press Enter. Only the available array types will be displayed on the screen.
(RAID 0 or RAID 1 requires two drives.)
2. Under the item "Arrays Label", type in a label and press <Enter>. Note: The
label shall not be more than 15 characters.)
3. For RAID 0, select the desired stripe size. Note: Available stripe sizes are 16,
32, and 64 KB. 64K is default. Please do not change the default setting.)
4. The item: "Create RAID via" allows you to select between the different ways
of creating methods for RAID 0 and RAID 1.
The following table gives examples of when each is appropriate.
Raid Level Create Via When Appropriate
RAID 0
RAID 0
No Init
Migrate
(*Note)
Build1
Creating a RAID 0 on new drives
Creating a RAID 0 from one new drive and
one drive with data you wish to preserve
Any time you wish to create a RAID 1, but especially if
you have data on one drive that you wish to preserve
Creating a RAID 1 on new drives, or when you want to
ensure that the array contains no data after creation.
Fastest way to create a RAID 1.
RAID 1
RAID 1
RAID 1
RAID 1
Clear
Quick
Init
Appropriate when using new drives
Note: If you select Migrate for RAID 0, or Build for RAID 1, you will be asked to
select the source drive. The contents of the source drive will be preserved. How-
ever, the data on the new drive will be lost.
D-9
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
5. When you are finished, press <Done> (as the screen shown below).
Notes:
1. Before adding a new drive to an array, be sure to back up any data stored on
the new drive; otherwise, all data will be lost.
2. If you stop the Build or Clear process on a RAID 1, you can restart it by press-
ing <Ctrl> and <R>.
3. If you've used the Quick Init option to create a RAID1, it may return some
data mis-comparison when you run a consistency check at a later time. This is
normal.
4. The Adaptec Host RAID allows you to use drives of different sizes in a RAID.
However, you can only select a smaller drive as the source or first drive during
a build operation.
5. When migrating from single volume to RAID 0, migrating from a larger drive to
a smaller drive is allowed. However, the destination drive must be at least half the
capacity of the source drive.
6. It is not recommended that you migrate or build an array on Windows dynamic
disks (volumes) because it will result in data loss.
Warning: Do not interrupt the process when you create a RAID 0 using the Migrate
option. If you do, you will not be able to restart the system, or to recover the data
that was on the source drive.
D-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Adding a Bootable Array
To make an array bootable:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the array you want to make bootable, and press
<Ctrl> and <B>.
3. Enter Y to create a bootable array when the following message is displayed:
"This will make all other existing bootable array non-bootable. Do you want to make
this array bootable? (Yes/No):" Then, a bootable array will be created. An asterisk
() will appear next to the bootable array (as shown in the picture below:)
Deleting a Bootable Array
To delete a bootable array:
1. From the Main menu, select Manage Arrays.
2. From the List of Arrays, select the bootable array you want to delete, and press
<Ctrl> and <B>. Note: a bootable array is the array marked with an asterisk (as
shown in the picture above.)
3. When the following message is displayed: "The array is already marked
bootable. Do you want to make this array as not bootable? (Yes/No)," Enter Y to
delete a bootable array. The bootable array will be deleted and the asterisk will
disappear.
Note: Do not use the delete key to delete the bootable array.
D-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Adding/Deleting Hotspares
To add a Hotspare:
Note: In order to rebuild a RAID (RAID 0 or RAID 1), you would need to add a
new HDD as a hotspare.
1. From the main menu (shown on Page D-4), select Add/Delete Hotspares.
2. Use the up and down arrow keys to highlight and select the disk you want to
designate as a hotspare, and press <Insert>, and then, press <Enter>.
3. Press Yes when the following prompt is displayed:
"Do you want to create spare?" (Yes/No?)
The spare you have selected will appear in the Selected drives Menu.
To delete a Hotspare:
1. From the main menu (shown on Page D-4), select Add/Delete Hotspares.
2. Use the up and down arrow keys to highlight and select the Hotspare you want
to delete, and press <delete>, and then, press <Enter>.
3. When the following warning is displayed: "Do you want to delete the hot spare?"
(Yes/No?), press Yes to delete the hotspare you have selected.
D-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Viewing Array Properties
To view the properties of an existing array:
1. From the main menu, select Manage Arrays and hit <Enter> (as shown on the
previous page.)
2. From the List of Arrays dialog box (shown below), select the array you want to
view and press Enter.
The Array Properties dialog box appears (as shown below), showing detailed
information on the array. The physical disks associated with the array are dis-
played here.
3. Press Esc to return to the previous menu.
D-13
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Rebuilding Arrays
Note 1: Rebuilding applies to Fault Tolerant array (RAID 1) only.
If an array Build process is interrupted or when one critical member is missing,
you must perform a Rebuild to restore its functionality. For a critical array rebuild
operation, the optimal drive is the source drive.
Note 2: If no spare array exists and a hard disk drive fails, you need to create a
spare before you can rebuild an array.
To Rebuild an array:
1 From the Main Menu, select Manage Arrays (as shown in the screen below).
From the List of Arrays, select the array you want to rebuild.
2 Press <Ctrl> and <R> to rebuild.
D-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
Deleting Arrays
Warning!! Back up the data on an array before you delete it to prevent data loss
Deleted arrays cannot be restored.
To delete an existing array:
1. From the main menu (shown on Page D-4), select Manage Arrays.
2. Select the array you wish to delete and press <delete>.
3. In the Array Properties dialog box, select Delete and press <Enter>. The fol-
lowing prompt is displayed:
Warning!! Deleting the array will render array unusable. Do you want to delete
the array? (Yes/No):
RAID 1 only—the following prompt is also displayed:
Deleting the partition will result in data loss! Do you also want to delete the parti-
tion? (Yes/No):
4. Press Yes to delete the array and partition or No to return to the previous
menu.
5. Press Esc to return to the previous menu.
D-15
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Using the Disk Utilities
The Disk Utilities enable you to format or verify the media of your Serial ATA
hard disks.
To access the disk utilities:
1. From the Adaptec RAID Configuration Utility Menu, select Disk Utilities (as
shown above) and press <Enter>. The following screen appears.
2. Select the desired disk and press <Enter>. The following screen appears:
D-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
To format a disk:
Note: The operation of Formatting Disk allows you to perform a low-level format-
ting of a hard drive by writing zeros to the entire disk. Serial ATA drives are low-level
formatted at the factory and do not need to be low-level formatted again.
3. When the screen shown below displays, select Format Disk and press <Enter>.
The following screen appears:
4. Read the warning message when it appears in the screen as shown below. To
continue with disk formatting, select Yes and hit <Enter>. Otherwise, select No
and press <Enter>.
Caution: Formatting a disk destroys all data on the drive. Be sure to back up
your data before formatting a disk.
D-17
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
To verify disk media:
3. When the screen shown above displays, select Verify Disk Media and press
<Enter>.
4. A message will display, indicating that the selected drive will be scanned for
media defects. Select Yes and hit <Enter> to proceed with disk verifying; other-
wise, select No and hit <Enter>.
D-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: Adaptec HostRAID Setup Guidelines
To Exit Adaptec RAID Configuration Utility
1. Once you have completed RAID array configurations, press ESC to exit. The
following screen will appear.
2. Press Yes to exit the Utility.
D-19
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
D-2
Installing the Intel ICH9R Driver by Adaptec
and the OS
a. Insert Supermicro's bootable CD that came with the package into the CD Drive
during the system reboot, and the screen: "Supermicro Driver Diskette Maker"
will appear.
b. Choose from the list the item: "Intel ICH9R Driver by 3rd Party (Adaptec)" and
press <Enter>.
c. From the next screen displayed, choose the OS driver you want to install and
press <Enter>.
d. Insert a formatted diskette into drive A: and press <Enter> as prompted.
e. Exit the program after the process is completed. Then, reboot the system.
f. Insert the Microsoft Windows OS Setup CD in the CD Driver, and the system
will start to boot up from CD.
g. Press the <F6> key when the message-"Press F6 if you need to install a third
party SCSI or RAID driver" displays.
h. When the Windows OS Setup screen appears, press "S" to specify additional
device(s).
i. Insert the driver diskette-"Adaptec Embedded Serial ATA Raid Controller Driver"
into Drive A: and press the <Enter> key.
j. Choose the Adaptec Embedded Host Serial ATA Raid Controller from the list
indicated in the Windows OS Setup Screen, and press the <Enter> key.
k. Press the <Enter> key to continue the installation process. (If you need to
specify any additional devices to be installed, do it at this time.) Once all devices
are specified, press the <Enter> key to continue with the installation.
l. From the Windows OS Setup screen, press <Enter>. The OS Setup will automati-
cally load all device files, and, then, continue with the Windows OS installation.
m. After the Windows OS Installation is completed, the system will automatically
reboot.
D-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Software Installation Instructions
Appendix E
Software Installation Instructions
E-1
Installing Drivers
After you've installed the Windows Operating System, a screen as shown below
will appear. You are ready to install software programs and drivers that have not
yet been installed. To install these software programs and drivers, click the icons
to the right of these items.
Driver/Tool Installation Display Screen
Note: Click the icons showing a hand writing on the paper to view the readme files
for each item. Click a computer icon to the right of an item to install an item (from
top to the bottom) one at a time. After installing each item, you must re-boot
the system before proceeding with the next item on the list. The bottom icon
with a CD on it allows you to view the entire contents of the CD.
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
E-2
Configuring Supero Doctor III
The Supero Doctor III program is a Web-base management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called the SD III Client. The Supero Doctor III program
included on the CDROM that came with your motherboard allows you to monitor
the environment and operations of your system. Supero Doctor III displays crucial
system information such as CPU temperature, system voltages and fan status. See
the Figure below for a display of the Supero Doctor III interface.
Note 1: Both default user name and password are ADMIN.
Note 2: In the Windows OS environment, the Supero Doctor III settings take pre-
cedence over the BIOS settings. When first installed, Supero Doctor III adopts the
temperature threshold settings previously set in the BIOS. Any subsequent changes
to these thresholds must be made within Supero Doctor, since the SD III settings
override the BIOS settings. For the Windows OS to adopt the BIOS temperature
threshold settings, please change the SDIII settings to be the same as those set
in the BIOS.
Supero Doctor III Interface Display Screen-I (Health Information)
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: Software Installation Instructions
Supero Doctor III Interface Display Screen-II (Remote Control)
Note: SD III Software Revision 1.0 can be downloaded from our Web site at: ftp://
ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's
Guide at: http://www.supermicro.com/PRODUCT/Manuals/SDIII/UserGuide.pdf. For
Linux, we will still recommend that you use Supero Doctor II.
E-3
Download from Www.Somanuals.com. All Manuals Search And Download.
C2SBA+II/C2SBA+/C2SBA/C2SBE User's Manual
Notes
E-4
Download from Www.Somanuals.com. All Manuals Search And Download.
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Download from Www.Somanuals.com. All Manuals Search And Download.
|