®
SUPER
SC512 Chassis Series
SC512-260B
SC512F-600B
SC512-200B
SC512F-520(B)
SC512F-410(B)
SC512F-260(B)
SC512L-260(B)
SC512L-200B
SC512F-600LB
SC512F-520L(B)
SC512L-260(B)-LCD
SC512F-350B
SC512C-260(B)
SC512C-200(B)
SC512F-280(B)
USER’S MANUAL
1.0b
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SC512 1U chassis. Installa-
tion and maintenance should be performed by experienced technicians only.
Supermicro’s SC512 1U chassis features a unique and highly-optimized design
for dual-core Xeon platforms. The chassis is equipped with a 200, 260, 280. 350,
410, 520 or 600 Watt high-efficiency power supply for superb power savings. High-
performance fans provide ample optimized cooling for FB-DIMM memory modules
in a 1U form factor.
This document lists compatible parts available when this document was published.
Always refer to the our Web site for updates on supported parts and configura-
tions.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Manual Organization
Chapter 1: Introduction
The first chapter provides a checklist of the main components included with this
chassis and describes the main features. This chapter also includes contact infor-
mation.
Chapter 2: System Safety
This chapter lists warnings, precautions, and system safety. You should thoroughly
familiarize yourself with this chapter for a general overview of safety precautions
that should be followed before installing and servicing this chassis.
Chapter 3: Chassis Components
Refer to this chapter for details on this chassis model including the fans, bays,
airflow shields, and other components.
Chapter 4: System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
Chapter 5: Chassis Setup and Maintenance
Follow the procedures given in this chapter when installing, removing, or
reconfiguring your chassis.
Chapter 6: Rack Installation
Refer to this chapter for detailed information on chassis rack installation. You should
follow the procedures given in this chapter when installing, removing or reconfiguring
your chassis into a rack environment.
Appendix A Cables, Screws, and Other Accessories
Appendix B Power Supply Specifications
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table of Contents
About This Manual.............................................................................................iii
Manual Organization..........................................................................................iv
Chapter 1 Introduction
1-1
1-2
Overview ......................................................................................................... 1-1
Chassis Features ............................................................................................ 1-2
CPU................................................................................................................. 1-2
I/O Expansion slots......................................................................................... 1-2
Peripheral Drives............................................................................................. 1-2
Dual Hard Drives............................................................................................. 1-2
Contacting Supermicro.................................................................................... 1-3
Returning Merchandise for Service................................................................. 1-4
1-3
1-4
Chapter 2 System Safety
2-1
2-2
2-3
2-4
2-5
2-6
Overview ......................................................................................................... 2-1
Warnings and Precautions.............................................................................. 2-1
Preparing for Setup......................................................................................... 2-1
Electrical Safety Precautions .......................................................................... 2-1
General Safety Precautions............................................................................ 2-3
System Safety................................................................................................. 2-3
Chapter 3 Chassis Components
3-1
3-2
Overview ......................................................................................................... 3-1
Components.................................................................................................... 3-1
Chassis............................................................................................................ 3-1
Fans ................................................................................................................ 3-1
Blower ............................................................................................................. 3-1
Mounting Rails ................................................................................................ 3-1
Power Supply.................................................................................................. 3-2
Air Shroud ....................................................................................................... 3-2
Where to get Replacement Components........................................................ 3-2
Chassis Model Options................................................................................... 3-2
Identifying Fan and Blower-Cooled Chassis Models...................................... 3-2
Model SC512 .................................................................................................. 3-4
Model SC512C................................................................................................ 3-5
Model SC512F ................................................................................................ 3-6
Model SC512L................................................................................................. 3-9
3-3
3-4
v
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Chapter 4 System Interface
4-1
4-2
4-3
Overview ......................................................................................................... 4-1
Control Panel Buttons..................................................................................... 4-2
Control Panel LEDs ........................................................................................ 4-2
Chapter 5 Chassis Setup and Maintenance
5-1
5-2
Overview ......................................................................................................... 5-1
Installation Procedures.................................................................................... 5-1
General Maintenance...................................................................................... 5-1
Removing the Chassis Cover ......................................................................... 5-2
Installing Hard Drives...................................................................................... 5-3
Installing the Motherboard .............................................................................. 5-5
Important Motherboard Installation Information .............................................. 5-5
Standoffs ......................................................................................................... 5-6
Installing the DVD or CD-ROM Drive ............................................................. 5-7
Expansion Slot Setup...................................................................................... 5-8
Installing the Air Shroud.................................................................................. 5-9
Installation Complete..................................................................................... 5-10
System Fans ..................................................................................................5-11
System Fan Tray............................................................................................5-11
System Fan Tray Replacement..................................................................... 5-12
Power Supply ............................................................................................... 5-13
Power Supply Failure.................................................................................... 5-13
Replacing the Chassis LED Panel................................................................ 5-15
5-3
5-4
5-5
5-6
5-7
5-8
5-9
Chapter 6 Rack Installation
6-1
6-2
6-3
Overview ......................................................................................................... 6-1
Unpacking the System.................................................................................... 6-1
Preparing for Setup......................................................................................... 6-1
Choosing a Setup Location............................................................................. 6-1
Rack Precautions............................................................................................ 6-2
General Server Precautions............................................................................ 6-2
Rack Mounting Considerations....................................................................... 6-3
Ambient Operating Temperature ................................................................ 6-3
Reduced Airflow ......................................................................................... 6-3
Mechanical Loading ................................................................................... 6-3
Circuit Overloading..................................................................................... 6-3
Reliable Ground ......................................................................................... 6-3
Rack Mounting Instructions............................................................................. 6-4
Identifying the Sections of the Rack Rails (Optional Item)............................. 6-4
6-4
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Installing the Inner Rail Extension .................................................................. 6-5
Installing the Outer Rails to the Rack............................................................. 6-6
Installing the Chassis into a Rack................................................................... 6-8
Mid-Mount Telco Rack..................................................................................... 6-9
Installing the Chassis into a Rack in Mid-Mount Position .............................. 6-9
Appendix A Cables, Screws, and Other Accessories
Appendix B Power Supply Specifications
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Notes
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
Supermicro’s SC512 1U chassis features a unique and highly-optimized design.
The chassis is equipped with a high-efficiency power supply in a small form factor
for optimized space efficiency.
The following chart lists model numbers and features currently available at the
time of printing. For additional information visit the Supermicro Web site at www.
supermicro.com
SC512 Chassis
Model
CPU
HDD
I/O Slots
Power Supply
SC512-200B
200W (High-Efficiency)
260W
UP
UP
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
2x Fixed 3.5"
2x Fixed 3.5"
1x Fixed 3.5"
2x Fixed 3.5"
2x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
1x Fixed 3.5"
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
FH
SC512-260B
SC512C-200(B)
SC512C-260(B)
SC512F-260(B)
SC512L-200B
SC512L-260(B)
SC512L-260(B)-LCD
SC512F-280(B)
SC512F-350B
SC512F-410(B)
SC512F-520(B)
SC512F-600B
SC512F-520L(B)
SC512F-600LB
UP
200W
UP
260W
UP
260W
UP
200W
UP
260W
UP
260W
DP/UP
DP/UP
DP/UP
DP/UP
DP/UP
DP/UP
DP/UP
280W (High-Efficiency)
350W (Gold Level)
410W DC
520W (High-Efficiency)
600W (Gold Level)
520W (High-Efficiency)
600W (Gold Level)
Legend:
DP = Dual Processor Support
FF = Full-height, Full-length
LP = Low-profile
UP = Single Processor Support
FH = Full-height, Half-length
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
1-2 Chassis Features
The SC512 1U high-performance chassis supports a wide range of features. See
the Chassis Components section of this manual for a list of featues included in
each of the SC512 models.
CPU
The SC512 chassis supports a DP and/or UP Xeon, Pentium D, P3/P4 processors.
Please refer to the motherboard specifications pages on our web site for updates
on supported processors.
I/O Expansion slots
Each version of the SC512 chassis includes one full I/O expansion slot
Peripheral Drives
Some SC512 chassis support peripheral dives such as a DVD-ROM, CD-ROM or
floppy disk drive. These drives allow data to be installed or saved quickly.
Dual Hard Drives
Some SC512 chassis models support a second hard disk drive. For more details,
check the Chassis Components section of this manual or the Supermicro Website
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
1-3 Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel:
+1 (408) 503-8000
+1 (408) 503-8008
Fax:
Email:
[email protected] (General Information)
Web Site:
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
Email:
+31 (0) 73-6416525
[email protected] (General Information)
[email protected] (Customer Support)
Asia-Pacific
Address:
Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel:
+886-(2) 8226-3990
+886-(2) 8226-3991
Fax:
Web Site:
Technical Support:
Email:
886-2-8226-1900
Tel:
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
1-4 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required be-
fore any warranty service will be rendered. You can obtain service by calling your
vendor for a Returned Merchandise Authorization (RMA) number. When returning
to the manufacturer, the RMA number should be prominently displayed on the
outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and
handling charges will be applied for all orders that must be mailed when service
is complete.
supermicro.com/support/rma/).
Whenever possible, repack the chassis in the original Supermicro carton, using the
original packaging material. If these are no longer available, be sure to pack the
chassis securely, using packaging material to surround the chassis so that it does
not shift within the carton and become damaged during shipping.
This warranty only covers normal consumer use and does not cover damages in-
curred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product problems.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: System Safety
Chapter 2
System Safety
2-1 Overview
This chapter provides a quick setup checklist to get your chassis up and running.
Following the steps in order given should enable you to have your chassis setup and
operational within a minimal amount of time. This quick setup assumes that you are
an experienced technician, famailiar with common concepts and terminology.
2-2 Warnings and Precautions
You should inspect the box the chassis was shipped in and note if it was damaged
in any way. If the chassis itself shows damage, file a damage claim with carrier
who delivered your system.
Decide on a suitable location for the rack unit that will hold that chassis. It should
be situated in a clean, dust-free area that is well venilated. Avoid areas where heat,
electrical noise and eletromagnetic fields are generated.
You will also need it placed near at least one grounded power outlet. When config-
ured, the SC512 chassis includes one power supply.
2-3 Preparing for Setup
The SC512 chassis includes a set of rail assemblies, including mounting brackets
and mounting screws you will need to install the systems into the rack. Please read
this manual in its entirety before you begin the installation procedure.
2-4 Electrical Safety Precautions
Basic electrical safety precautions should be followed to protect yourself from harm
and the SC512 from damage:
•
Be aware of the locations of the power on/off switch on the chassis as well
as the room’s emergency power-off switch, disconnection switch or electrical
outlet. If an electrical accident occurs, you can then quickly remove power from
the system.
•
Do not work alone when working with high-voltage components.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512F Chassis Manual
•
Power should always be disconnected from the system when removing or in-
stalling main system components, such as the serverboard, memory modules
and the DVD-ROM and floppy drives (not necessary for hot-swappable drives).
When disconnecting power, you should first power down the system with the
operating system and then unplug the power cords from all the power supply
modules in the system.
•
•
When working around exposed electrical circuits, another person who is fa-
miliar with the power-off controls should be nearby to switch off the power, if
necessary.
Use only one hand when working with powered-on electrical equipment. This
is to avoid making a complete circuit, which will cause electrical shock. Use
extreme caution when using metal tools, which can easily damage any electrical
components or circuit boards they come into contact with.
•
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed
as electrical insulators.
•
•
The power cord must include a grounding plug and must be plugged into a
grounded electrical outlet.
Serverboard battery: CAUTION - There is a danger of explosion if the onboard
battery is installed upside down, which will reverse its polarities This battery
must be replaced only with the same or an equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
•
DVD-ROM laser: CAUTION - This server may have come equipped with a
DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous
radiation exposure, do not open the enclosure or use the unit in any uncon-
ventional way.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: System Safety
2-5 General Safety Precautions
•
•
Keep the area around the chassis clean and free of clutter.
Place the chassis top cover and any system components that have been re-
moved away from the system or on a table so that they won’t accidentally be
stepped on.
•
•
•
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or
be pulled into a cooling fan.
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact
with printed circuit boards or areas where power is present.
After accessing the inside of the system, close the system back up and secure
it to the rack unit with the retention screws after ensuring that all connections
have been made.
2-6 System Safety
Electrostatic discharge (ESD) is generated by two objects with different electrical
charges coming into contact with each other. An electrical discharge is created to
neutralize this difference, which can damage electronic components and printed
circuit boards. The following measures are generally sufficient to neutralize this
difference before contact is made to protect your equipment from ESD:
•
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed
as electrical insulators.
•
•
Use a grounded wrist strap designed to prevent static discharge.
Keep all components and printed circuit boards (PCBs) in their antistatic bags
until ready for use.
•
Touch a grounded metal object before removing any board from its antistatic
bag.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512F Chassis Manual
•
•
Do not let components or PCBs come into contact with your clothing, which may
retain a charge even if you are wearing a wrist strap.
Handle a board by its edges only; do not touch its components, peripheral chips,
memory modules or contacts.
•
•
When handling chips or modules, avoid touching their pins.
Put the serverboard and peripherals back into their antistatic bags when not
in use.
•
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the serverboard.
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Chassis Components
Chapter 3
Chassis Components
3-1 Overview
This chapter describes the most common components included with your chassis.
Some components listed may not be included or compatible with your particular
chassis model. For more information, see the installation instructions detailed later
in this manual.
3-2 Components
Chassis
Depending on the model, the SC512 chassis may include one slim DVD-ROM/CD-
ROM bay, at least one fixed hard drive, a floppy drive, and/or two USB ports. For
Fans
The SC512 model chassis accepts two or three system fans powered by the moth-
erboard. These fans are 1U high and are powered by 3-pin connectors.
Blower
The SC512, SC512L and SC512C model chassis use a single blower unit for
system cooling.
Mounting Rails
The SC512 can be placed in a rack for secure storage and use. To set up your
rack, follow the step-by-step instructions included in this manual. SC512 models
with narrow chassis designs include specialized rails for mounting in a standard
rack. See the Rack Installation section of this manual for details.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Power Supply
Each SC512 chassis model includes a high-efficiency power supply rated at 200,
260, 280, 350, 410 or 580 Watts. In the unlikely event your power supply fails,
replacement is simple and can be done without tools.
Air Shroud
Air shrouds are shields, usually plastic, that funnel air directly to where it is needed.
Always use the air shroud included with your chassis.
3-3 Where to get Replacement Components
Though not frequently, you may need replacement parts for your system. To en-
sure the highest level of professional service and technical support, we strongly
recommend purchasing exclusively from our Supermicro Authorized Distributors/
System Integrators/Resellers. A list of Supermicro Authorized Distributors/System
to Buy link.
3-4 Chassis Model Options
The following section lists the different options which are available for each of the
different chassis models in the SC512 chassis family of products.
Identifying Fan and Blower-Cooled Chassis Models
Your SC512 chassis is equipped with either a blower unit or a set of system fans
for optimized chassis cooling.
The SC512, SC512C and most SC512L model chassis use a blower unit for chas-
sis cooling.
The SC512F model chassis are cooled with system fans. The number of system
fans included in your specific system may vary.
See the following page for illustrations of blower units and system fans. For detailed
instructions on replacing a blower unit or system fans, see the Chassis Setup and
Maintenance section of this manual.
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Chassis Components
Air blower unit
included in chassis
models SC512,
SC512C and SC512L
Figure 3-1: Blower-Cooled Chassis Model
System fans included
in chassis model
SC512F
Figure 3-2: Fan-Cooled Chassis Model
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Model SC512
Includes a slot with a dummy cover plate where an optional DVD-ROM drive may
be installed, and a 200 or 260 Watt power supply. The SC512 model chassis is
cooled with an internal blower unit.
Dummy Cover
Plate for Optional
DVD Drive
Figure 3-3: Chassis Model SC512-200, SC512-260
SC512-200
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard Blower Optional
DVD
-
2x
USB
UP
FH
1x
Fixed
3.5"
200 Watt
High-
Efficiency
SC512-260
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard Blower Optional
DVD
-
2x
USB
UP
FH
1x
Fixed
3.5"
260 Watt
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Chassis Components
Model SC512C
The SC512C includes a CD-ROM drive, floppy drive, USB ports and a 200 or 260
Watt power supply. The SC512C model chassis is cooled with an internal blower
unit.
CD-ROM Drive
USB Ports
Floppy Drive
Figure 3-4: Chassis Model SC512C
SC512C-200
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard
Blower
1x CD
1x
2x
UP
FH
1x
200
Floppy USB
Fixed
3.5"
Watt
SC512C-260
Chassis Blower/
Fan
DVD/
CD
Floppy USB CPU
I/O
Slots
HDD
Power
Supply
Standard
Blower
1x CD
1x
2x
UP
FH
1x
260
Floppy USB
Fixed
3.5"
Watt
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Model SC512F
The SC512F models may include a DVD-ROM drive, USB ports and a 260, 280,
350, 410, 520 or 600 Watt power supply. The SC512F-280 and 350 models can sup-
port a second optional hard disk drive. The SC512F-280/350/410/520/ 600 model
chassis have a wider chassis design, which mounts in a standard rack utilizing
special mounting rails. See the Rack Installation section of this manual for details.
All SC512F model chassis are cooled with system fans.
DVD-ROM Drive
Figure 3-5: Chassis Model SC512F-260
SC512F-260
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Narrow*
2x Fan
1x DVD
-
2x
UP
FH
1x
260 Watt
USB
Fixed
3.5"
* Note: Narrow chassis models include specialized mounting rails to fit into a stan-
dard rack. See the Rack Installation section of this manual for details.
DVD-ROM Drive
Figure 3-6: Chassis Model SC512F-280
SC512F-280
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard 2x Fan
1x DVD
-
-
DP/
UP
FH
2x
Fixed
3.5"
280 Watt
High-
Efficiency
Optional DVD-ROM Drive
Figure 3-7: Chassis Model SC512F-350
SC512F-350
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard 2x Fan Optional
DVD
-
-
DP/
UP
FH
2x
Fixed
3.5"
350 Watt
Gold-
Level
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Chassis Components
USB Ports
DVD-ROM Drive
Figure 3-8: Chassis Models SC512F-410 and SC512F-520
SC512F-520
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard 3x Fans 1x DVD
-
2x
DP/
FH
1x
Fixed
3.5"
520 Watt
High-
Efficiency
USB UP
SC512F-410
Chassis Blower/
Fan
DVD/
CD
Floppy USB CPU
I/O
Slots
HDD
Power
Supply
Standard 3x Fans 1x DVD
-
2x
USB
DP/
UP
FH
1x
Fixed
3.5"
410 DC
Optional DVD-ROM
Figure 3-9: Chassis Model SC512F-600
SC512F-600
Chassis Blower/
Fan
DVD/
CD
Floppy USB CPU
I/O
Slots
HDD
Power
Supply
Standard
3x Fan Optional
DVD
-
2x
USB
DP/
UP
FH
1x
Fixed
3.5"
600
Watt
Gold
Level
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Figure 3-10: Chassis Model SC512F-520L and SC512F-600L
SC512F-520L
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard 3x Fans
-
-
-
DP/
UP
FH
1x
Fixed
520 Watt
High
3.5" Efficiency
SC512F-600L
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard 3x Fans
-
-
-
DP/
UP
FH
1x
Fixed
3.5"
600 Watt
Gold
Level
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: Chassis Components
Model SC512L
The SC512L models include two 3.5" hard disk drives and a 200 or 260 Watt power
supply. The SC512L model chassis is cooled with an internal blower unit.
Figure 3-11: Chassis Models SC512L-200 and SC512L-260
SC512L-200
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard Blower
-
-
-
UP
FH
2x
200
Fixed
3.5"
Watt
SC512L-260
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard Blower
-
-
-
UP
FH
2x
260
Fixed
3.5"
Watt
Figure 3-12: Chassis Model SC512L-260-LCD
SC512L-260(B)-LCD
Chassis Blower/ DVD/CD Floppy USB CPU
Fan
I/O
Slots
HDD
Power
Supply
Standard
Blower
-
-
-
UP
FH
1x
260
Fixed
3.5"
Watt
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Notes
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: System Interface
Chapter 4
System Interface
4-1 Overview
There are several LEDs on the control panel and on the drive carriers to keep you
constantly informed of the overall status of the system, as well as the activity and
health of specific components. Most SC512 models have two buttons on the chassis
control panel: a reset button and an on/off switch. This chapter explains the mean-
ings of all LED indicators and the appropriate response you may need to take.
Figure 4-1: Chassis LED and Buttons
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
4-2 Control Panel Buttons
There are two push-buttons located on the front of the chassis. These are a reset
button and a power on/off button.
Reset: The reset button is used to reboot the system.
Power: The main power switch is used to apply or remove power from the
power supply to the server system. Turning off system power with this button re-
moves the main power but keeps standby power supplied to the system. Therefore,
you must unplug system before servicing.
4-3 Control Panel LEDs
The control panel located on the front of the SC512 chassis has five LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.
Overheat/Fan Fail: When this LED flashes it indicates a fan failure. When
continuously on (not flashing) it indicates an overheat condition, which may be
caused by cables obstructing the airflow in the system or the ambient room tem-
perature being too warm. Check the routing of the cables and make sure all fans
are present and operating normally. You should also check to make sure that the
chassis covers are installed. Finally, verify that the heatsinks are installed properly.
This LED will remain flashing or on as long as the overheat condition exists.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: System Interface
NIC2: Indicates network activity on GLAN2 when flashing.
NIC1: Indicates network activity on GLAN1 when flashing.
HDD: Indicates IDE channel activity. SAS/SATA drive, SCSI drive, and/or
DVD-ROM drive activity when flashing.
Power: Indicates power is being supplied to the system's power supply units.
This LED should normally be illuminated when the system is operating.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Notes
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
Chapter 5
Chassis Setup and Maintenance
5-1 Overview
This chapter covers the steps required to install components and perform mainte-
nance on the chassis. The only tool you will need to install components and perform
maintenance is a Phillips head and a flathead screwdriver. Print this page to use
as a reference while setting up your chassis.
5-2 Installation Procedures
Removing the Chassis Cover
Installing the Hard Drive
Installing the Motherboard (includes I/O Shield and Expansion Card Slot setup)
Installing the DVD or CD-ROM Drive
Installing the Air Shroud
General Maintenance
Systems Fans
Power Supply
Certain motherboards and heatsinks may not be compatible
with this chassis. Before installation, review the motherboard
installation procedures in this chapter.
!
Review the warnings and precautions listed in the manual be-
fore setting up or servicing this chassis. These include infor-
mation in Chapter 2: System Safety and the warning/precau-
tions listed in the setup instructions.
!
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
5-3 Removing the Chassis Cover
Remove these screws
Remove these screws
Flat head
6-32 x 5 mm
[0.197]
Remove this screw
Figure 5-1: Removing the Chassis Cover
Removing the Chassis Cover
1. Remove the screws holding the chassis cover in place.
2. Apply pressure to the middle front of the chassis cover.
3. Slide the cover toward the rear of the chassis.
Warning: Except for short periods of time, do NOT operate the
server without the cover in place. The chassis cover must be in
place to allow proper airflow and prevent overheating.
!
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-4 Installing Hard Drives
Remove these screws
Flat head
6-32 x 5 mm
[0.197]
DVD-ROM/CD-ROM
Drive
Figure 5-2: Removing the CD-ROM Drive to Access the Hard Drive
Installing a Hard Drive
Before adding a hard drive, you must remove the DVD-ROM/CD-ROM drive.
1. Open the chassis cover.
2. If you have not already done so, remove the fan tray. For more information on
removing the fan tray, see the Maintenance section located at the end of this
chapter.
3. Remove the CD-ROM drive. To do this, remove the two screws holding the
drive in place. One screw is external. The other is internal.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Hard Drive
Flat head
6-32 x 5 mm
[0.197]
Figure 5-3: Adding the Hard Drive
4. Place the hard drive in the chassis as illustrated. Make sure the hard drive con-
nectors face the inside of the chassis.
5. Secure the hard drive to the chassis using the four screws.
6. SC512F-280, SC512L and SC512L-260 model users: These chassis can support
a second hard drive. Insert the second hard drive at this time. If you are are not
using the models listed above, skip this step.
Hard Drive
Second Hard
Drive
Flat head
6-32 x 5 mm
[0.197]
Figure 5-4: Adding a Second Hard Drive
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-5 Installing the Motherboard
Flat head
6-32 x 5 mm
[0.197]
Figure 5-5: The SC512 Backplate (I/O Shield)
Important Motherboard Installation Information
Before installing the motherboard, be aware of the following:
I/O Shield Backplate
The backplate holds the motherboard ports in place. Your motherboard must match
SC512 backplate. If your motherboard does not match, you must choose a different
motherboard.
Heatsinks
Some compatible motherboards require heatsinks to lower the temperature of the
components. Heatsinks for the SC512 chassis must be rated for 1U or less.
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Standoffs
Standoffs prevent short circuits by securing space between the motherboard and
the chassis surface. The SC512 chassis includes permanent standoffs in locations
used by most motherboards. These standoffs accept the rounded Phillips head
screws included in the SC512 accessories packaging.
Round head
3 x 5 mm
[0.197]
Figure 5-6: Installing the Motherboard
Installing the Motherboard
1. Review the documentation that came with your motherboard. Become familiar
with component placement, requirements, precautions, and cable connec-
tions.
2. Open the chassis cover.
3. Align the motherboard with the chassis standoffs and carefully, place the
motherboard in the chassis. Make sure rear ports line up with the I/O shield.
4. Secure the motherboard to the chassis using the ten rounded, Phillips head
screws supplied with the accessories kit.
5. Secure the CPU(s), heatsinks, and other components to the motherboard as
described in the motherboard documentation. Do not exceed eight pounds of
torque when tightening down the motherboard.
6. Connect the cables between the motherboard, backplane, chassis, front
panel, and power supply, as needed.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-6 Installing the DVD or CD-ROM Drive
Replace these screws
Flat head
6-32 x 5 mm
[0.197]
DVD-ROM/CD-ROM
Drive
Hard Drive
Figure 5-7: Replace the DVD-ROM/CD-ROM Drive
Replacing the DVD or CD-ROM
1. Place the DVD-ROM or CD-ROM drive in the chassis above the hard drive.
2. Secure the drive with two screws. One screw is external. The other screw is
internal.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Expansion Slot Setup
SC512 chassis includes a slot for one full height/full length add-on card and a riser
card. The riser card allows the expansion card to fit within the small 1U form.
The expansion card slot does not require a screw to hold the card in place.
Add-on Card Slot Latch
Expansion Card
Slot Shield
Figure 5-8: Installing the Expansion Card
Installing Expansion Cards
1. Disconnect the power supply, lay the chassis on a flat surface, and open the
chassis cover.
2. Slide the add-on card clip upward.
3. Slide the add-on card slot shield toward the side of the chassis and remove
the Shield.
4. Secure the riser card to the motherboard.
5. Slide the add-on card (with "L" bracket) into the add-on card slot and the riser
card.
6. Replace the add-on card slot clip to secure the add-on card.
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-7 Installing the Air Shroud
The air shroud helps cool the chassis by directing heated air through the rear of
the chassis. When installing the air fan, be aware of the following:
•
•
The air shroud is designed to fit within the chassis. The sides of the air
shroud should remain straight in relation to the top. Do not fold or bend the
air shroud.
The air shroud has perforated tabs that can be removed if motherboard com-
ponents prevent proper air shroud installation. Do not remove a tab unless it
is necessary.
Incorrect
Incorrect
Correct
Figure 5-9: Air Shroud Placement
Perforated Tabs
Figure 5-10: Installing the Air Shroud in the SC512 Chassis
Installing The Air Shroud
1. Confirm that the air shroud matches your chassis model.
2. Place the air shroud in the chassis. The shroud sets directly behind the sys-
tem fans. If necessary, remove some perforated tabs to ensure a snug fit.
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Checking the Airflow in the Chassis
1. Make sure there are no objects to obstruct airflow in and out of the server.
2. Do not operate the server without drives or drive trays in the drive bays. Use
only recommended server parts.
3. Make sure no wires or foreign objects obstruct air flow through the chassis.
Pull all excess cabling out of the airflow path or use shorter cables.
The control panel LEDs inform you of system status. See “Chapter 3: System
Interface” for details on the LEDs and the control panel buttons.
Installation Complete
In most cases, the chassis power supply and fans are pre-installed. If you need to
install fans continue to the Systems Fan section of this chapter. If the chassis will be
installed into a rack, continue to the next chapter for rack installation instructions.
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-8 System Fans
Three heavy duty fans provide cooling for the chassis. These fans circulate air
through the chassis as a means of lowering the chassis internal temperature.
The SC512F-280 chassis accepts two fans instead of three.
System Fan Tray
Fan Tray Support Pin
Rubber Grommet
Figure 5-11: Placing the System Fan
System Fan Tray
Systems fan trays are components that house groups of fans. The system fan tray
is held in place by two rivets permanently attached to the chassis surface. Each
rivet is encircled by a rubber grommet to reduce vibration.
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
System Fan Tray Replacement
Installing the System Fan Tray
1. Power down the system.
2. Disconnect each fan from the motherboard.
3. Lift the system fan tray and fans from the chassis. Retain the rubber mount-
ings that encircle the tray rivets.
4. Place the fans into the new system fan tray. Make all the fans face the correct
direction.
5. Confirm the the rubber mountings are in place around the chassis rivets.
6. Align the fan tray with rivets and place the new fan tray (and system fans)
into the chassis.
7. Reconnect the system fans to the motherboard
Replacing Individual System Fans
Fans can be replaced individually without removing the system fan tray. There is
no need to power down the system when replacing a system fan.
Replacing System Fans
1. If necessary, open the chassis while the power is running to determine which
fan has failed. (Never run the server for an extended period of time with the
chassis open.)
2. Remove the failed fan's power cord from the serverboard.
3. Lift the failed fan completely from the chassis.
4. Place the new fan into the vacant space. Make sure the arrows on the top of
the fan (indicating air direction) point in the same direction as the arrows on
the other fan(s).
5. Confirm that the fan is working properly and replace the chassis cover..
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
5-9 Power Supply
Depending on your chassis model the SC512 chassis has a 200, 269, 280, 350,
410 or 520 Watt power supply. This power supply is auto-switching capable. This
enables it to automatically sense and operate at a 100v to 240v input voltage. An
amber light will be illuminated on the power supply when the power is off. An il-
luminated green light indicates that the power supply is operating.
Power Supply Failure
The SC512 series chassis has one power supply. In the unlikely event that the power
supply unit fails, the system will shut down and you will need to replace it.
Replacement units can be ordered directly from Supermicro (see contact information
in the preface) or an authorized reseller.
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Remove these screws
Power Supply
Pan Head
6-32 x 5mm
[0.197]
Remove this screw
Figure 5-12: Removing the Power Supply
Replacing the Power Supply
1. Disconnect the power cord from the from the chassis to ensure that the unit is
not accidentally plugged in.
2. Place the chassis on a stable hard surface and remove the chassis cover.
3. Disconnect the power supply from the motherboard and other chassis compo-
nents.
4. Remove the screws securing the power supply. Two screws are in the back
of the chassis and one underneath. Retain the screws and the internal brace
that connects the power supply to the chassis from underneath.
5. Pull the power supply out of the chassis.
6. Place the new power supply into the chassis and secure the power supply
using the three screws and internal brace.
7. Connect the power supply to the motherboard and other chassis components.
8. Connect the power cord to the power supply and power up the chassis/server.
9. Once you confirm that the power supply has been installed correctly, replace
the chassis cover.
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Chassis Setup and Maintenance
Figure 5-13: Replacing the LED Panel
Replacing the Chassis LED Panel
In the unlikely event that the chassis LED and buttons fail, you can replace the panel.
Replacement parts can be ordered from Supermicro or an authorized reseller.
Replacing the Chassis LED Panel
1. Power down and unplug the system.
2. Remove the chassis cover.
3. Disconnect the cord to the front panel.
4. Locate and remove three screws holding the panel in place. (If your chassis
supports dual hard drives, you may have to remove the second hard drive
from the chassis).
5. Install the new LED panel and secure the unit with three screws.
6. Reconnect the cables to the LED panel and if necessary, replace the hard
drive.
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Notes
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Rack Installation
Chapter 6
Rack Installation
6-1 Overview
This chapter provides a quick setup checklist to install the chassis into a rack.
6-2 Unpacking the System
You should inspect the box the chassis was shipped in and note if it was damaged
in any way. If the chassis itself shows damage you should file a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold your chassis. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fields are generated. You will also need
it placed near a grounded power outlet. Be sure to read the Rack and Server Pre-
cautions in the next section.
6-3 Preparing for Setup
The box your chassis was shipped in should include two sets of rail assemblies,
two rail mounting brackets and the mounting screws you will need to install the
system into the rack. Please read this section in its entirety before you begin the
installation procedure outlined in the sections that follow.
Choosing a Setup Location
•
•
•
Leave enough clearance in front of the rack to enable you to open the front
door completely (~25 inches).
Leave approximately 30 inches of clearance in the back of the rack to allow for
sufficient airflow and ease in servicing.
This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Warnings and Precautions!
!
!
Rack Precautions
•
Ensure that the leveling jacks on the bottom of the rack are fully extended to
the floor with the full weight of the rack resting on them.
•
•
•
In single rack installation, stabilizers should be attached to the rack.
In multiple rack installations, the racks should be coupled together.
Always make sure the rack is stable before extending a component from the
rack.
•
You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
General Server Precautions
•
•
•
•
Review the electrical and general safety precautions that came with the com-
ponents you are adding to your chassis.
Determine the placement of each component in the rack before you install the
rails.
Install the heaviest server components on the bottom of the rack first, and then
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
•
•
Allow the hot plug hard drives and power supply modules to cool before touch-
ing them.
Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Rack Installation
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
6-4 Rack Mounting Instructions
This section provides information on installing the SC512 chassis into a rack unit
with the rails provided. There are a variety of rack units on the market, which
may mean the assembly procedure will differ slightly. You should also refer to the
installation instructions that came with the rack unit you are using.
NOTE: The SC512F-280/350/410/520/600 chassis models are designed with a
wider chassis. The rails for these chassis will fit a rack between 25.6" and 33.05"
deep. The following shows how to mount these chassis to a standard rack.
Identifying the Sections of the Rack Rails (Optional Item)
The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections: an inner fixed chassis rail that secures
directly to the server chassis, and an outer fixed rack rail that secures directly to
the rack itself.
The SC512F comes with "chassis ears" that allow the chassis to use generic
rails.
Inner Rails
Chassis Ears
Outer Rails
Figure 6-1: Identifying the Sections of the Rack Rails
(Right side rail shown)
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Rack Installation
Installing the Inner Rail Extension
The SC512F includes chassis ears that you must remove before installing the
rails.
Removing the Chassis Ears
1. Locate and remove the three screws holding the chassis ear in place.
2. Repeat step on with the other chassis ear.
Flat head
M4 x 4 mm
[0.157]
Figure 6-2: Installing Inner Rails to the Chassis
Installing the Inner Rails
1. Place the inner rail on the side of the chassis aligning the hooks of the chas-
sis with the rail holes.
2. Slide the rail toward the front of the chassis to secure the rail in place.
3. Secure the chassis with four screws.
4. Repeat steps 1-3 for the other inner rail extension.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Flat head
M5 x 12 mm [0.472]
Washer for M5
Secure to the
Rear of the Rack
Attach Outer Racks
together
Secure to the
Front of the Rack
Figure 6-3: Assembling the Outer Rails
Installing the Outer Rails to the Rack
Installing the Outer Rails
1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.
2. Adjust both the short and long brackets to the proper distance so that the rail
fits snugly into the rack.
3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
Use a washer with each screw.
4. Repeat steps 1-4 for the left outer rail.
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Rack Installation
3
1
3
1
2
1
Figure 6-4: Installing the Outer Rails to the Server Rack
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Figure 6-5: Installing the Chassis into a Rack
Installing the Chassis into a Rack
Installing the Chassis
1. Confirm that the inner rails are attached to the chassis. Also, confirm that the
outer rails are installed on the rack.
2. Align chassis rails with the front of the rack rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into the locked position.
4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Rack Installation
Mid-Mount Telco Rack
The SC512.supports Telco rack installation. The SC512 chassis compact design
allows the chassis to be installed into a Telco rack without the use of rails.
Place chassis
ears here
Flat head
M4 x 4 mm
[0.157]
Figure 6-6: Moving the Chassis Ears for Telco Rack Installation
Installing the Chassis into a Rack in Mid-Mount Position
Instaling into a Mid-Mount Position Rack
1. If it is necessary to install the chassis in a mid-mount Telco rack, remove the
chassis rails and the chassis ears (if the ears are installed at the front of the
chassis).
2. Locate the three screw holes in the middle of the chassis and secure the ears
to the chassis with three flat head screws. Make sure the screws are secure,
but do not over tighten the screws.
6-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Flat head
M5 x 12 mm [0.472]
Washer for M5
Figure 6-7: Installing the Server into a Telco Rack
3. Hold the chassis in the telco rack and screw the chassis to the rack using the
three screw holes located in the chassis ears.
4. The chassis is held in place by the chassis ears and does not slide in and out
of place.
6-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: SC512 Chassis Cables
Appendix A
Cables, Screws,
and Other Accessories
A-1 Overview
This appendix lists supported cables for your chassis system. It only includes the
most commonly used components and configurations. For more compatible cables,
refer to the manufacturer of the motherboard you are using and our Web site at:
A-2 Cables Included with SC512 Chassis
SC512-200 and SC512-260
Part #
Type
Cable
Wire
Length
Description
CBL-0049L
Front cable 16-pin to 16-pin
CBL-0084L
CBL-0260L
CBL-0261L
9 cm
DVD cable (lead free).
US power cord 18 AWG
40cm 7-pin SATA cable S-RA
Cable
Cable
Cable
40cm
4-pin to 1x SATA (RA) + 1x 4-pin
(RA) + 1x FPD PWS
CBL-0262L
CBL-0263L
77cm
9-pin to 9-pin internal USB cable
SC512F-260
Length
Part #
Type
Cable
Wire
Description
CBL-0049L
Front cable 16-pin to 16-pin
CBL-0084L
CBL-0260L
9 cm
DVD cable (lead free).
US power cord 18 AWG
4-pin to 1x SATA (RA) + 1x 4-pin
(RA) + 1x FPD PWS
CBL-0262L
CBL-0263L
Cable
Cable
77cm
9-pin to 9-pin internal USB cable
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
SC512F-280
Length
Part #
Type
Description
7-pin SATA with two 90 degree side
connectors (lead free).
CBL-0142L
Cable
30 cm (~12")
CBL-0156L
CBL-0084L
-
Cable
Wire
40 cm
9 cm
6'
16-pin to 16-pin FP cable. Lead free.
DVD cable. Lead free.
Cable
Regional power cord
SC512F-350
Part #
Type
Cable
Cable
Cord
Length
30cm
40cm
6 feet
40cm
Description
CBL-0142L
CBL-0156L
CBL-0260L
CBL-0261L
7-pin 2-side SATA RA-RA cable
Front ctrl cable round 16 to 16-pin
US power cord 18AWG
Cable
7pin SATA cable S-RA
4-pin to 1x SATA (RA) + 1x4-pin
(RA) + 1x FPD PWS EXT. cable
CBL-0262L
Cable
-
SC512F-410
Part #
Type
Length
Description
7-pin SATA with two 90 degree side
connectors (lead free).
CBL-0142L
Cable
30 cm (~12")
CBL-0156L
CBL-0084L
Cable
Wire
40 cm
9 cm
16-pin to 16-pin FP cable. Lead free.
DVD cable. Lead free.
SC512F-520
Part #
Type
Length
Description
7-pin SATA with two 90 degree side
connectors (lead free).
CBL-0142L
Cable
30 cm (~12")
CBL-0156L
CBL-0084L
-
Cable
Wire
40 cm
9 cm
6'
16 pin to 16 pin FP cable. Lead free.
DVD Cable. Lead free.
Cable
Regional power cord
SC512F-600
Part #
Type
Length
Description
7-pin SATA with two 90 degree side
connectors (lead free).
CBL-0142L
Cable
30 cm (~12")
16-pin to 16-pin FP Cable. Lead
Free.
CBL-0156L
-
Cable
Cable
40 cm
6'
Regional power cord
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: SC512 Chassis Cables
SC512F-520L and SC512F-600L
Part #
Type
Length
Description
7-pin SATA with two 90 degree side
connectors (lead free).
CBL-0142L
Cable
30 cm (~12")
16-pin to 16-pin FP Cable. Lead
Free.
CBL-0156L
-
Cable
Cable
40 cm
6'
Regional power cord
SC512L-200 and SC512L-260
Part #
Type
Length
Description
CBL-0049L
Cable
Wire
Front cable 16-pin to 16-pin
CBL-0084L
CBL-0260L
CBL-0261L
9 cm
DVD cable (lead free).
US power cord 18 AWG
40cm 7-pin SATA cable S-RA
Cable
Cable
Cable
40cm
4-pin to 1x SATA (RA) + 1x 4-pin
(RA) + 1x FPD PWS
CBL-0262L
CBL-0263L
77cm
9-pin to 9-pin internal USB cable
SC512L-260-LCD
Length
Part #
CBL-0049
CBL-0121
Type
Cable
Description
9 cm
16-pin to 16-pin ribbon cable
10-pin to 4-pin cable for LCD
USB 2.0
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Extending Power Cables
Although Supermicro chassis are designed with to be efficient and cost-effective,
some compatible motherboards have power connectors located in different areas.
To use these motherboards you may have to extend the power cables to the mother
boards. To do this, use the following chart as a guide.
Power Cable Extenders
Number of Pins
24-pin
Cable Part #
CBL-0042
CBL-0059
CBL-0062
CBL-0060
Length
7.9”(20 CM)
7.9”(20 CM)
7.9”(20 CM)
7.9”(20 CM)
20-pin
8-pin
4-pin
Front Panel to the Motherboard
The SC512 chassis includes a cable to connect the chassis front panel to the
motherboard. If your motherboard uses a different connector, use the following list
to find a compatible cable.
Front Panel to Motherboard Cable (Ribbon Cable)
Number of Pins
(Front Panel)
Number of Pins
(Motherboard)
Cable Part #
16-pin
16-pin
20-pin
16-pin
20-pin
16-pin
20-pin
20-pin
varies*
varies*
CBL-0049
CBL-0048
CBL-0047
CBL-0068
CBL-0067
* Split cables: Use these cable if your motherboard requires several different con-
nections from the front panel.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: SC512 Chassis Cables
A-3 Routing the Chassis Cables
In order for the SC512 chassis to perform safely and efficiently, it is important that the
cables are routed correctly. Follow the instructions below and review both the cabling
diagram and photograph to ensure that the cabling has been properly routed.
Preparing the Chassis for Cable Routing
1. Unplug the chassis from any power source.
2. Review the diagram on the following page, taking note of the naming of each
cable.
3. Remove the screws securing the fan platform to the bottom of the chassis.
PWR
3C
1
MOTHERBOARD
AREA
1C
1
MB SATA
PORTS
5A
1
2C
1
4A
SATA PWR
1
(RIGHT ANGLE)
LEFTMIDDLE BRACKET
RIGHT MIDDLE BRACKET
3B
1
HDD
HDD
1B
FAN
2B
1
1
SATA
(RIGHT ANGLE)
SATA
(STRAIGHT)
SATA PWR
(RIGHT ANGLE)
2A
1
1A
1
3A
1
Figure A-1: Chassis Cable Routing Diagram (SC512L-200/260)
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Routing Cable (1A) from Hard Drive (1B)
1. Plug cable (1A) into the SATA port of hard drive (1B).
2. Lift up the fan and run cable (1A) straight out from the port and under the fan.
3. Route cable (1A) over the hard drive and through the left middle bracket.
4. Plug cable (1A) into upper SATA port (1C) on the motherboard.
Routing Cable (2A) from Hard Drive (2B)
1. Plug cable (2A) into the SATA port of hard drive (2B).
2. Run cable (2A) upwards at a right angle, up and over the top of hard drive
(2B).
3. Route cable (2A) through the left middle bracket.
4. Plug cable (2A) into lower SATA port (2C) on the motherboard.
Routing Split Cable (3A)(4A) from Hard Drives (1B)(2B) to the Power Supply
1. Plug the end of the split cable (3A) into hard drive (2B).
2. Route the end of the split cable (3A) straight up at a right angle, beside the
fan, and over the top of cable (1A).
3. Plug the end of the split cable (3A) into connector (3B).
4. Plug the other end of the split cable (4A) into hard drive (1B).
5. Route the end of the split cable (4A) straight up at a right angle, along the top
of the fan.
6. Route cable (5A) through the right middle bracket and plug it into connector
(3B).
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: SC512 Chassis Cables
Checking the Cable Routing
1. Check the cable routing by following out each cable in the previous steps and
comparing them to the diagram in Figure A-1, and the photograph in Figure
A-2.
Figure A-2: Chassis Cable Routing
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
A-4 Chassis Screws
The Chassis and accessory box include all the screws needed to setup your
chassis. This section include descriptions of the most common screws used. Your
chassis may not require all the parts listed.
M/B
HARD DRIVE
Flat head
6-32 x 5 mm
[0.197]
Pan head
6-32 x 5 mm
[0.197]
DVD-ROM CD-ROM FLOPPY DRIVE
Flat head
6-32 x 5 mm
[0.197]
Round head
2.6 x 5 mm
[0.197]
Round head
3 x 5 mm
[0.197]
Pan head
6-32 x 5 mm
[0.197]
RAIL
Flat head
M4 x 4 mm
[0.157]
Round head
M4 x 4 mm
[0.157]
Flat head
M5 x 12 mm [0.472]
Washer for M5
M/B STANDOFF
M/B standoff
6-32 to 6-32
Thumb screw
6-32 x 5 mm [0.197]
M/B (CPU) standoff
M5 to 6-32
Figure A-3: Chassis Screws
A-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: SC512F Power Supply Specifications
Appendix B
Power Supply Specifications
This appendix lists power supply specifications for your chassis system.
SC512 Chassis Model
200
PWS-201-1H
260
MFR Part #
PWS-0055
100 - 240V
50 - 60Hz
4 - 2A Max
100 - 240V
60 - 50Hz
4A Max
Rated AC Voltage
+5V standby 2.0A
2.0A
+12V 16.0A
+5V 8.0A
18.0A
25.0A
15.0A
1.0A
+3.3V 8.0A
-12V 0.5A
SC512C Chassis Models
200
260
MFR Part #
PWS-0043
PWS-0055
100 - 240V
60 - 50Hz
5 - 3A
100 - 240V
60 - 50Hz
4A Max
Rated AC Voltage
+5V standby 2.0A
2.0A
+12V 12.0A
+5V 20A
18.0A
25.0A
15.0A
1.0A
+3.3V 17.0 A
-12V 0.8A
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
SC512F Chassis Models (See below for 410 model)
260 280 350 520/520L
PWS-0055 PWS-281-1H PWS-351-1H PWS-521-1H PWS-601-1H
600/600L
MFR
Part #
Rated
AC
Voltage 4A Max
100 - 240V 100 - 240V
100-240 V,
50-60 Hz,
4.2 - 1.8A
100 - 240V
50 - 60Hz
7 - 3A
100 - 240V
50 - 60Hz
7.5 - 3.1A
60 - 50Hz
50 - 60Hz
5A Max
+5V
2.0A
2A
3A
3A
3A
standby
+12V 18.0A
+5V 25.0A
+3.3V 15.0A
-12V 1.0A
23A
18A
15A
1A
29A
18A
15A
-
39A
20A
16A
0.5A
49A
20A
16A
0.5A
SC512F-410 Chassis Model
410
MFR Part #
DC Voltage
PWS-0061
Voltage Range = -36V to -72V
Nominal Voltage = -48V
Max Input Current = 18A @ -48V
DC Output 5V + 3.3V ≤ 180W
+5V 35.0A
+5V standby 3.0A
+12V 32.0A
-12V 0.5A
+3.3V 20.0A
SC512L Chassis Models
200
260/260-LCD
PWS-0055
MFR Part #
PWS-0043
100 - 240V
60 - 50Hz
5-3A
100 - 240V
60 - 50Hz
4A Max
Rated AC Voltage
+5V standby 2.0A
2.0A
+12V 12.0A
+5V 20A
18.0A
25.0A
15.0A
1.0A
+3.3V 17.0A
-12V 0.8A
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: SC512F Power Supply Specifications
Notes
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SC512 Chassis Manual
Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life sup-
port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to per-
form be reasonably expected to result in significant injury or loss of life or catastrophic
property damage. Accordingly, Supermicro disclaims any and all liability, and should
buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold
Supermicro harmless for and against any and all claims, demands, actions, litigation,
and proceedings of any kind arising out of or related to such ultra-hazardous use or
sale.
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|