SY-K7VEMPRO
Motherboard
****************************************************
AMD® Athlon/Duron
Processor supported
VIA VT8361 AGP/PCI Motherboard
200/266 MHz Front Side Bus supported
Micro-ATX Form Factor
****************************************************
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SY-K7VEMPRO
Table of Contents
CHAPTER 1 MOTHERBOARD DESCRIPTION...............................1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
INTRODUCTION..............................................................1
KEY FEATURES...............................................................1
HANDLING THE MOTHERBOARD ..............................3
ELECTROSTATIC DISCHARGE PRECAUTIONS.........3
SY-K7VEMPRO MOTHERBOARD LAYOUT................4
SY-K7VEMPRO MOTHERBOARD COMPONENTS.....5
MICROPROCESSOR........................................................7
MEMORY..........................................................................8
CHIPSET............................................................................9
I/O INTERFACE CONTROLLER...................................12
HARDWARE MONITOR................................................15
WAKE ON LAN TECHNOLOGY ..................................16
CHAPTER 2 HARDWARE INSTALLATION ...................................17
2-1
2-2
2-3
PREPARATIONS.............................................................17
UNPACKING THE MOTHERBOARD ..........................18
INSTALLATION GUIDE ................................................19
2-3.1
CPU Installation ........................................................... 20
SDRAM Memory Module Installation......................... 26
Motherboard Connector.............................................. 28
CPU FSB Setting (JP3)................................................. 41
CMOS Clearing (JP5)................................................... 41
Power On ...................................................................... 42
Quick BIOS Setup.......................................................... 43
Troubleshooting at First Start ....................................... 44
Power Off ...................................................................... 46
2-3.2
2-3.3
2-3.4
2-3.5
2-3.6
2-3.7
2-3.8
2-3.9
CHAPTER 3 BIOS SETUP UTILITY.................................................47
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SY-K7VEMPRO
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
STANDARD CMOS SETUP..........................................50
ADVANCED BIOS FEATURES ......................................54
ADVANCED CHIPSET FEATURES ...............................59
INTEGRATED PERIPHERALS.......................................64
POWER MANAGEMENT SETUP..................................69
PNP/PCI CONFIGURATION SETUP..............................73
PC HEALTH STATUS......................................................76
LOAD FAIL-SAFE DEFAULTS ......................................78
LOAD OPTIMIZED DEFAULTS.....................................79
SUPERVISOR PASSWORD ............................................80
USER PASSWORD ..........................................................81
BOOT MENU ...................................................................82
CHAPTER 4 DRIVERS INSTALLATION ..........................................83
CHAPTER 5 REALTEK LAN DRIVER INSTALLATION ...............88
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
Chapter 1
MOTHERBOARD DESCRIPTION
1-1 INTRODUCTION
The SY-K7VEMPRO AGP/PCI Motherboard is a high-performance
Socket 462 Micro-ATX form-factor system board. The SY-K7VEMPRO
uses VIA Chipset technology and supports Socket 462 class processors.
This Motherboard is fully compatible with industry standards and adds
many technical enhancements.
1-2 KEY FEATURES
ꢀ CPU SUPPORT
The SY-K7VEMPRO supports a wide range of AMD CPUs:
ꢁ
Supports 200MHz Front Side Bus on Athlon(750MHz~1.3GHz)/
Duron(600MHz~950MHz)
ꢁ
Supports 266MHz Front Side Bus on Athlon(1GHz~1.33GHz)
New released AMD Socket 462 CPUs will very likely be supported by the
SY-K7VEMPRO as well.
ꢀ CPU SETTINGS
ꢁ
CPU FSB Frequency
The SY-K7VEMPRO supports 100/133 MHz FSB CPU.
ꢀ EXPANDABILITY
The SY-K7VEMPRO provides all the standard expansion slots, and many
more additional expansion features:
ꢂ Expansion slots
ꢁ
ꢁ
3 x 32-bit bus master PCI slots
1 x 16-bit ISA slot
ꢂ Enhanced IO
ꢁ
ꢁ
Floppy disk controller
2x EIDE controllers with support for up to 4 Ultra DMA
33/66/100 devices
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Standard/EPP/ECP parallel port
1x 16550 compatible serial ports
IrDA compatible infrared port
2x USB (Universal Serial Bus) connectors
PS/2 mouse connector
PS/2 keyboard connector
ꢀ ADVANCED FUNCTIONS
The SY-K7VEMPRO supports advanced functions such as:
Wake-On-LAN
ꢁ
Supports Wake-On-LAN (Some advanced network cards can
wake the system up over the network, the WOL connector is
provided by the SY-K7VEMPRO to support this function).
ꢁ
Multiple boot
The SY-K7VEMPRO supports booting from devices such as
CD-ROM.
ꢁ
Power on by modem or alarm
If the SY-K7VEMPRO system is in suspend mode, it can be switched
back on through the modem or RTC alarm through this function. This
opens a lot of possibilities, such as remote access that switches the
system on only after the modem receives a call.
ꢀ FAIL SAFE
The SY-K7VEMPRO comes with added functionality to make managing
the system easy and safe
ꢂ Hardware Monitor
The integrated VIA Hardware Monitor IC and Hardware doctor software
enables the user to monitor system voltages, temperatures and FAN speeds.
This makes sure that the user is full control of the system
ꢀ SOYO Bonus Pack CD-ROM
ꢀ COMPLIANCE
The SY-K7VEMPRO complies with all important industry standards. The
following underlines the reliability of the SY-K7VEMPRO, a motherboard
to trust.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
ꢁ
PC99, ACPI compliant
ꢀ USER FRIENDLY
ꢁ
Jumperless design
1-3 HANDLING THE MOTHERBOARD
To avoid damage to your Motherboard, follow these simple rules while
unpacking:
ꢀ Before handling the Motherboard, ground yourself by grasping an
unpainted portion of the system's metal chassis.
ꢀ Remove the Motherboard from its anti-static packaging. Hold the
Motherboard by the edges and avoid touching its components.
ꢀ Check the Motherboard for damage. If any chip appears loose, press
carefully to seat it firmly in its socket.
Warning: Do not apply power if the Motherboard appears
damaged. If there is damage to the board, contact your dealer
immediately.
1-4 ELECTROSTATIC DISCHARGE PRECAUTIONS
Make sure to ground yourself before handling the Motherboard or other
system components. Electrostatic discharge can easily damage the
components. Note that you must take special precautions when handling
the Motherboard in dry or air-conditioned environment.
To protect your equipment from electrostatic discharge, take the following
precautions:
ꢀ Do not remove the anti-static packaging until you are ready to install.
ꢀ Ground yourself before removing any system component from its
protective anti-static packaging. (To ground yourself, grasp the expansion
slot covers or other unpainted portions of the computer chassis.)
ꢀ Frequently ground yourself while working or use a grounding strap.
ꢀ Handle the Motherboard by its edges and avoid touching its
components.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-5 SY-K7VEMPRO MOTHERBOARD LAYOUT
PS/2 KB
Connector
PS/2 Mouse
Connector
3
1
CPUFAN1
6
2
5
1
J28
COM 1
3
1
VGA
JP3
IDE 1 IDE 2
USB 1_2
ATX Power
6
2
5
JOYSTICK
J30
LINE-OUT
LINE-IN
1
FDC1
1
3
MIC JACK
CHIPFAN
COM2
RTL8139C
1
5
SIRCON1
HDD
LED
Speaker
PCI Slot #1
_
+
VT1611A
PWRBT
Reset
Power /
ACPI
LED
JP5
1
4
1
3
CDIN1
PCI Slot #2
PCI Slot #3
JP44
3V
Lithium
Battery
ISA Slot #1
Back Panel
SY-K7VEMPRO Platform
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-6 SY-K7VEMPRO MOTHERBOARD COMPONENTS
A B C
D
E
Z
F
G
H
Y
X
W
V
I
RTL8139C
J
U
T
VT1611A
K
S
R
Q
3V
L
M
Lithium
Battery
P
O N
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
A
B
C
D
E
F
G
H
I
Keyboard & Mouse Front Panel Header
ATX Power Supply Connector
CPU Cooling Fan Connector
Socket 462 Connector
DIMM Banks
CPU FSB Selection Jumper
Floppy Disk Drive (FDD) Port
Bus Mastering E-IDE/ATAPI Ports
VIA VT8361 North Bridge chip
Realtek RTL8139C Ethernet LAN chip
Front panel connectors
J
K
L
USB Port3, Port4
M 32-bit PCI Mastering Slots
N
O
P
Flash BIOS
VIA 82C686B South Bridge chip
16-bit ISA Slot
Q
R
S
3V Lithium Battery
Wake-On-LAN (WOL) Header
CMOS Clear Jumper
AC97 Codec Chip
T
U
V
CD In Connector
Chipset Fan Connector
W COM2 Serial Port
X
Y
Z
Serial Infrared (IrDa) Device Header
Audio Mic & Earphone Front Panel Header
VGA Connector
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-7 MICROPROCESSOR
The motherboard supports a single Socket 462 processor. The processor’s
VID pins automatically program the voltage regulator on the motherboard
to the required processor voltage. In addition, the front side bus speed (100
MHz) is automatically selected.
1-7.1 Microprocessor Packaging
The CPU is packaged in a 462 pin PGA package. A fan must be used to
ensure adequate cooling.
1-7.2 Microprocessor Upgrades
The motherboard can be upgraded with Socket 462 processors that run at
higher speeds. When upgrading the processor, the SY-K7VEMPRO will
Auto-Detect the new processor speed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-8 MEMORY
1-8.1 Main Memory
The motherboard has two DIMM sockets. SDRAM can be installed in one,
two, or sockets. Using the serial presence detect (SPD) data structure,
programmed into an E²PROM on the DIMM, the BIOS can determine the
SDRAM’s size and speed. Minimum DIMM memory size is 32 MB;
maximum DIMM memory size is 1GB. Memory size and speed can vary
between sockets.
The motherboard supports the following memory features:
DRAM interface synchronous with host CPU (100/133MHz)
Concurrent CPU, AGP, and PCI access
Supports SDRAM and VCM SDRAM memory types
Different DRAM types may be used in mixed combinations
Different DRAM timing for each bank
Dynamic Clock Enable (CKE) control for SDRAM power
reduction in high speed system.
The K7VEMPRO supports 2 DIMMs or 4 banks at 133MHz for
1GB max memory)
Flexible row and column addresses
64-bit data width only
Supports PC100 and PC133 SDRAM
Independent SDRAM control for each bank
Seamless DRAM command scheduling for maximum DRAM bus
utilization (e.g., precharge other banks while accessing the current
bank)
Four cache lines (16quadwords) of CPU to DRAM write buffers
Four cache lines of CPU to DRAM read prefetch buffers
Read around write capability for non-stalled CPU read
Speculative DRAM read before snoop result
Burst read and write operation
BIOS shadow at 16KB increment
Decoupled and burst DRAM refresh with staggered RAS timing
CAS before RAS or self refresh
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-9 CHIPSET
ꢀ
VT8361
The KLE133 chip set consists of the VT8361 system controller (552 pin
BGA) and the VT82C686B PCI to ISA bridge (352 pin BGA). The system
controller provides superior performance between the CPU, DRAM and
PCI bus with pipelined, burst, and concurrent operation.
The VT8361 supports four banks of DRAMs up to 1GB. The DRAM
controller supports standard, Synchronous DRAM (SDRAM), in a flexible
mix / match manner. The Synchronous DRAM interface allows zero wait
state bursting between the DRAM and the data buffers at 100/133 MHz.
The four banks of DRAM can be composed of an arbitrary mixture of
1M/2M/4M/8M/16M/32MxN DRAMs.
The VT8361 system controller also supports full AGP v2.0 capability for
maximum bus utilization including 1x/2x/4x mode transfers, SBA (Side
Band Addressing), Flush/Fence commands, and pipelined grants. An eight
level request queue plus a four level post-write request queue with
thirty-two and sixteen quad words of read and write data FIFO’s
respectively are included for deep pipelined and split AGP transactions. A
single-level GART TLB with 16 full associative entries and flexible
CPU/AGP/PCI remapping control is also provided for operation under
protected mode operating environments. Both Window 95 VxD and
Windows 98 /Windows 2000 mini port drivers are supported for
interoperability with major AGP-based 3D and DVD- capable multimedia
accelerators.
The VT8361 supports two 32-bit 3.3/5V system buses (one AGP and one
PCI) that are synchronous/ pseudo-synchronous to the CPU bus. The chip
also contains a built-in bus-to-bus bridge to allow simultaneous concurrent
operations on each bus. Five levels (double words) of post write buffers
are included to allow for concurrent CPU and PCI operation. For PCI
master operation, forty-eight levels (double words) of post write buffers
and sixteen levels (double words) of prefetch buffers are included for
concurrent PCI bus and DRAM/cache accesses. The chip also supports
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
enhanced PCI bus commands such as Memory-Read-Line,
Memory-Read-Multiple and Memory-Write-Invalid commands to
minimize snoop overhead. In addition, advanced features are supported
such as snoop ahead, snoop filtering, L1 write-back forward to PCI master,
and L1 write-back merged with PCI post write buffers to minimize PCI
master read latency and DRAM utilization. Delay transaction and read
caching mechanisms are also implemented for further improvement of
over all system performance.
The 352-pin Ball Grid Array VT82C686B PCI to ISA bridge supports four
levels (double words) of line buffers, type F DMA transfers and delay
transaction to allow efficient PCI bus utilization The VT82C686B also
includes an integrated keyboard controller with PS/2 mouse support,
integrated DS12885 style real time clock with extended 256 byte CMOS
RAM, integrated master mode enhanced IDE controller with full scatter/
gather capability and extension to UltraDMA-33/66 for 33/66 MB/sec
transfer rate, integrated USB interface with root Hub and two function
ports with built-in physical layer transceivers, Distributed DMA supports,
and On Now/ ACPI compliant advanced configuration and power
management interface.
For sophisticated power management, the Via 8361 provides independent
clock stop control for the CPU/SDRAM, PCI, and AGP buses and
Dynamic CKE control for powering down of the SDRAM. A separate
suspend-well plane is implemented for the SDRAM control signals for
Suspend-to-DRAM operation. Coupled with the VT82C686B south bridge
chip, a complete power conscious PC motherboard can be implemented
with no external TTLs.
The Via 8361 chipset is ideal for high performance, high quality, high
energy efficient and high integration desktop AGP / PCI computer
systems.
ꢀ
VT82C686B
The VT82C686B PSIPC (PCI Super-I/O integrated Peripheral Controller)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
is a high integration, high performance, power-efficient, and high
compatibility device that supports AMD and non-AMD based processor to
PCI bus bridge functionality to make a complete Microsoft
PC99-compliant PCI/ISA system In addition to complete ISA extension
bus functionality, the VT82C686B includes standard AMD ligent
peripheral controllers:
1)Master mode enhanced IDE controller with dual channel DMA engine
and interlaced dual channel commands. Dedicated FIFO coupled with
scatter and gather master mode operation allows high performance
transfers between PCI and IDE \devices. In addition to standard PIO and
DMA mode operation, the VT82C686B also supports the UltraDMA-33
standard to allow reliable data transfer rates up to 33MB/sec throughput.
The VT82C686B also supports the UltraDMA-66 standard. The IDE
controller is SFF-8038I v1.0 and Microsoft Windows-family compliant.
2)Universal Serial Bus controller that is USB v1.1 and Universal HCI
v1.1 compliant. The VT82C686B includes the root hub with four
function ports with integrated physical layer transceivers. The USB
controller allows hot plug and play and isochronous peripherals to be
inserted into the system with universal driver support. The controller
also implements legacy keyboard and mouse support so that legacy
software can run transparently in non-USB-aware operating system
environment.
3)Keyboard controller with PS2 mouse support.
4)Real Time Clock with 256 byte extended CMOS. In addition to the
standard ISA RTC functionality, the integrated RTC also includes the
date alarm, century field, and other enhancements for compatibility with
the ACPI standard.
5)Hardware monitoring subsystem for managing system/ motherboard
voltage levels, temperatures, and fan speeds
6)Full System Management Bus (SMBus) interface.
7)Two 16550-compatible serial I/O ports with infrared communications
port option. A third serial port is available to be dedicated to the IR
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
interface.
8)Integrated PCI-mastering dual full-duplex direct-sound
AC97-link-compatible sound system. Hardware soundblaster-pro and
hardware-assisted FM blocks are included for Windows DOS box and
real-mode DOS compatibility. Loopback capability is also implemented
for directing mixed audio streams into USB and 1394 speakers for high
quality digital audio
9)Two game ports and One MIDI port
10) ECP/EPP-capable parallel port
11) Standard floppy disk drive interface
12) Distributed DMA capability for support O ISA legacy DMA over the
PCI bus. Serial IRQ is also supported for docking and non-docking
application.
13) Plug and Play controller that allows complete steerability of all PCI
interrupts and internal interrupts/ DMA channels to any interrupt
channel. One additional steerable interrupt channel is provided to allow
plug and play and reconfigurability of onboard peripherals for Windows
family compliance.
The VT82C686B also enhances the functionality of the standard ISA
peripherals. The integrated interrupt controller supports both edge and
level triggered interrupts channel by channel. The integrated DMA
controller supports type F DMA in addition to standard ISA DMA modes.
Compliant with the PCI2.2 specification, the VT82C686B supports
delayed transactions and remote power management so that slower ISA
peripherals do not block the traffic of the PCI bus. Special circuitry is built
in to allow concurrent operation without causing dead lock even in a
PCI-to PCI bridge environment. The chip also includes eight levels
(doublewords) of line buffers from the PCI bus to the ISA bus to further
enhance overall system performance.
1-10 I/O INTERFACE CONTROLLER
The motherboard uses the VT82C686B Super-I/O controller which
features:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
ꢀ
Supports 2 serial ports, IR port, parallel port, and floppy disk
controller functions
ꢀ
Two UARTs for Complete Serial Ports
Even, odd, stick or no parity bit generation and detection
Programmable baud rate generator
High speed baud rate (230Kbps, 460Kbps) support
Independent transmit/receiver FIFOs
Modem Control
Plug and play with 96 base IO address and 12 IRQ options
One dedicated IR port
ꢀ
Third serial port dedicated to IR function
IR function either through the two complete serial ports or the
third dedicated port
Infrared-IrDA (HPSIR) and ASK (Amplitude Shift Keyed) IR
Multi-mode parallel port
ꢀ
ꢀ
Standard mode, ECP and EPP support
Plug and play with 192 base IO address, 12 IRQ and 4 DMA
options
Floppy Disk Controller
16bytes of FIFO
Data rates up to 1Mbps
Perpendicular recording driver support
Two FDDs with drive swap support
Plug and play with 48 base IO address, 12 IRQ and 4 DMA
options
The Setup program provides configuration option for the I/O controller.
1-10.1 Serial Ports
The motherboard has one 9-pin D-Sub serial port connectors located on
the back panel. The NS16C5450-compatible UARTs support data transfers
at speeds up to 115.2 Kbits/sec with BIOS support.
1-10.2 Parallel Port
The connector for the multimode bi-directional parallel port is a 25-pin
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
D-Sub connector located on the back panel of the motherboard. In the
Setup program, there are four options for parallel port operation:
ꢃ
ꢃ
ꢃ
Compatible (standard mode)
Bi-directional (PS/2 compatible)
Bi-directional EPP. A driver from the peripheral manufacturer is
required for operation.
ꢃ
Bi-directional high-speed ECP
1-10.3 Diskette Drive Controller
The I/O controller is software compatible with the 82077 diskette drive
controller and supports both PC-AT and PS/2 modes. In the Setup program,
the diskette drive interface can be configured for the following diskette
drive capacities and sizes.
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
ꢃ
360 KB, 5.25-inch
1.2 MB, 5.25-inch
720 KB, 3.5-inch
1.2 MB. 3.5-inch (driver required)
1.25-1.44 MB, 3.5-inch
2.88 MB, 3.5-inch
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
1-10.4 PS/2 Keyboard and Mouse Interface
PS/2 keyboard and mouse connectors are located on the back panel of the
motherboard. The +5 V lines to keyboard and mouse connectors are
protected with a fuse that prevents motherboard components from being
damaged when an over-current condition occurs.
Note
The mouse and keyboard can be plugged into either PS/2 connector.
Power to the computer should be turned off before a keyboard or mouse is
connected or disconnected.
The keyboard controller contains code, which provides the traditional
keyboard and mouse control functions, and also supports Power On/Reset
password protection. Power On/Reset password can be specified in the
BIOS Setup program.
The keyboard controller also supports the hot-key sequence
<Ctrl><Alt><Del>, software reset. This key sequence resets the
computer’s software by jumping to the beginning of the BIOS code and
running the Power On Self Test (POST).
1-10.5 Infrared Support
On the front panel I/O connector, there are six pins that support Hewlett
Packard HSDL-1000 compatible infrared (IR) transmitters and receivers.
In the Setup program, Serial Port B can be direct4d to a connected IR
device. (In this case, the Serial Port B connector on the back panel cannot
be used.) The IR connection can be used to transfer files to or from
portable devices like laptops, PDAs, and printers. The Infrared Data
Association (IrDA) specification supports data transfers of 115Kbits/sec at
a distance of 1 meter.
1-11 HARDWARE MONITOR
The optional hardware monitor subsystem provides low-cost
instrumentation capabilities. The features of the hardware monitor
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Motherboard Description
SY-K7VEMPRO
subsystem include:
ꢀ
ꢀ
ꢀ
An integrated ambient temperature sensor
Fan speed sensors, which monitor the fan 1 and fan 2 connector.
Power supply voltage monitoring to detect levels above or below
acceptable values
When suggested ratings for temperature, fan speed, or voltage are
exceeded, an interrupt is activated. The hardware monitor component
connects to the SMBus.
1-12 WAKE ON LAN TECHNOLOGY
Wake on LAN technology enables remote wakeup of the computer
through a network. Wake on LAN technology requires a PCI add-in
network interface card (NIC) with remote wakeup capabilities. The remote
wakeup connector on the NIC must be connected to the onboard Wake on
LAN connector. The NIC monitors network traffic at the Ethernet interface;
upon detecting a Magic Packet, the NIC asserts a wakeup signal that
powers up the computer. This feature uses the Wake on LAN connector.
ꢀCAUTION
For Wake on LAN, the 5-V standby line for the power supply must be
capable of delivering +5V ±5 % at 720 mA. Failure to provide adequate
standby current when implementing Wake on LAN can damage the power
supply.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
Chapter 2
HARDWARE INSTALLATION
Congratulations on your purchase of SY-K7VEMPRO Motherboard. You
are about to install and connect your new Motherboard.
Note: Do not unpack the Motherboard from its protective
anti-static packaging until you have made the following
preparations.
2-1 PREPARATIONS
Gather and prepare all the following hardware equipment to complete the
installation successfully:
1.
Socket 462 processor with built-in CPU cooling fan (boxed type).
Note: This Motherboard supports non-boxed type CPUs. The heavier
CPU cooling fan requires the installation of a CPU support stand.
2.
3.
4.
5.
6.
7.
8.
9.
10.
DIMM memory module (s)
Computer case and chassis with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device (PS/2 mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive…
External Peripherals: Printer, Plotter, and Modem (optional)
Internal Peripherals: Modem and LAN cards (optional)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-2 UNPACKING THE MOTHERBOARD
When unpacking the Motherboard, check for the following items:
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
ꢂ
The SY-K7VEMPRO VT8361 AGP/PCI Motherboard
This Quick Start Guide
The Installation CD-ROM
SOYO Bonus Pack CD-ROM
One IDE Device ATA 66 Flat Cable
One Floppy Disk Drive Flat Cable
One Heat Sink Compound
One Serial port flat cable with a 9-pin connector
Warning: Do not unpack the Motherboard from its anti-static
packaging until you are ready to install it.
Like most electronic equipment, your Motherboard may be damaged by
electrostatic discharge. To avoid permanent damage to components ground
yourself while working by using a grounding strap. Otherwise, ground
yourself frequently by touching the unpainted portion of the computer
chassis to drain the static charges.
Handle the Motherboard carefully, holding it by the edges.
You are now ready to start the installation.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3 INSTALLATION GUIDE
We will now begin the installation of the Motherboard. Please follow the
step-by-step procedure designed to lead you to a complete and correct
installation.
Warning: Turn off the power to the Motherboard, system
chassis, and peripheral devices before performing any work on
the Motherboard or system.
BEGIN THE INSTALLATION
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.1 CPU Installation
Your SY-K7VEMPRO motherboard comes with a CPU retention set kit.
The retention set is used to hold the processor attached to the Socket 462
CPU connector on the motherboard.
Mark your CPU Frequency: Record the working frequency of
your CPU that should be clearly marked on the CPU cover.
FSB 200MHz Athlon
750MHz (100 x 7.5)
950MHz (100 x 9.5)
1.3GHz (100 x13.0)
800MHz (100 x 8.0)
1000MHz (100 x 10.0)
850MHz (100 x 8.5)
1.1GHz (100 x 11.0)
900MHz (100 x 9.0)
1.2GHz (100 x 12.0)
FSB 200MHz Duron
600MHz (100 x 6.0)
800MHz (100 x 8.0)
650MHz (100 x 6.5)
850MHz (100 x 8.5)
700MHz (100 x 7.0)
900MHz (100 x 9.0)
750MHz (100 x 7.5)
950MHz (100 x 9.5)
FSB 266MHz Athlon
1GHz (133 x 7.5)
1.13GHz (133 x 8.5)
1.2GHz (133 x 9.0)
1.33GHz (133 x 10.0)
Follow these instructions to install your Socket 462 processor correctly.
1. Lift the socket handle up to a vertical position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2. Align the blunt edge of the CPU with the matching pinhole
distinctive edge on the socket.
3. Seat the processor in the socket completely and without forcing.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
4. Then close the socket handle to secure the CPU in place.
Remember to connect the CPU Cooling Fan to the
appropriate power connector on the Motherboard. The fan is
a key component that will ensure system stability. The fan
prevents overheating, therefore prolonging the life of your
CPU.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
CPU Fan Mount Procedure: To prevent scratch or damage on the
motherboard, please follow these instruction on how to mount the CPU fan
properly.
1. Apply thermal paste to the die of the CPU.
2.Carefully mount the fan on top of the CPU and clip-on the first lock.
1
3.Clip-on the second lock and please make sure not to damage/scratch the
board.
2
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
4. The fans power connector should be connected to CPUFAN1.
3
CPUFAN1
1
Note: If the fan is defective or Power connector is not connected to CPUFAN1, the
system will enable FOC function see below for more information on FOC
function.
FOC ( Fan-Off Control )
The newly designed SOYO “FOC” is based on the concept of total
protection for CPU, which is very different from currently seen on the
market. The H/W control function is used to see a passive security system
of monitoring and warning. “FOC”, designed by SOYO, gives emphasis
on the concept of total protection. S/W Simultaneous Signal Follow-ups
techniques and Auto Power Off System are included to prevent all possible
damage caused by the MAL-functioning of the CPU fan. With the help of
“O/S On Time Monitoring And Warning” function, provided by the H/W
monitoring system, the double-protection purpose is achieved.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
“FOC” includes the following functions:
(1) Simultaneous Signal Follow Ups: Before the system enters the O/S,
H/W will detect the signals of the CPU fan pins, get their
revolution information and send it to the BIOS.
(2) Auto Power Off System: If the BIOS gets the information of CPU
fan revolution, it goes on working normally. If not, it will
inform the system and have the power supply disconnected
immediately. Thus, the CPU is protected from over heating.
Note: The following must be observed to secure the normal functioning of
“Fan-Off Control”:
1. CPU fan with sensor pins must be used.
2. CPU fans approved by AMD are strongly recommended.
3. The “HOT KEY” function is provided for the CPU fans without
sensor pins, to avoid the power off. Users may press the “Insert”
key to jump over the “Power Off” mode; go to the BIOS and
disable “FOC”. Now system can be booted normally.
4. The power connector of the CPU fan must be connected to the
specified “CPU Fan Connector” on the motherboard to secure the
normal functioning of the system.
We provide the following User-Friendly protection features:
1.Fan-Off Control : The motherboard detects the status of the CPU
fan and protects the CPU by automatically disconnecting the
power supply. The default value of this function is Enable. After
booting up, the user may disable it.
2.CPU Socket Sticker : Users will find a sticker on the CPU socket,
which reminds
them of the correct usage of the K7 CPU.
3. Heat Dissipation Paste: Heat Dissipation Paste is included for all
Socket-A motherboards, to enhance the heat dissipation
capability.
Furthermore, we strongly recommend our users to enable the function of H/W
monitoring in the BIOS. This function, together with the FOC, provide the total
protection to the CPU and allow it to maximize its performance.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.2 SDRAM Memory Module Installation
RTL8139C
VT1611A
3V
Lithium
Battery
Your board comes with two DIMM sockets, providing support for up to
1GB of main memory using unbuffered DIMM modules from 32MB to
512MB. On this motherboard, DRAM speed can be set independent from
the CPU front side bus speed. Depending on the DRAM clock speed
setting in the BIOS setup (Chapter 3), appropriate memory modules must
be used. For 100MHz DRAM speed, use PC100 memory; for 133MHz
DRAM speed, use PC133 memory.
84
1
1
84
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
Memory Configuration Table
Number of Memory
DIMM 1
DIMM 2
Modules
RAM Type
SDRAM
32/64/128/256/512 MB
Memory Module Size
(MB)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3 Motherboard Connector
RTL8139C
VT1611A
Pin-1
IDE 1
IDE 2
Primary
IDE
Secondary
IDE
3V
Lithium
Battery
2-3.3.1
IDE Device Installation (HDD, CD-ROM)
This Motherboard offers two primary and secondary IDE device
connectors (IDE1, IDE2). It can support up to four high-speed Ultra DMA
33/66HDD or CD-ROM.
Connect one side of the ATA66/100 flat cable to the IDE device (HDD or
CD-ROM) and plug the other end to the primary (IDE1) or secondary
(IDE2) directionally keyed IDE connector on the Motherboard. The
ATA66/100 cable is backward compatible with ATA33 HDDs.
This Motherboard can support up to four HDDs.
80-Conductor
ATA 66/100
Flat Cable
40-pin
1
1
39
39
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3.2 Floppy Drive Installation
Pin -1
RTL8139C
FDC
VT1611A
Floppy Drive
Connector
3V
Lithium
Battery
The system supports 5 possible floppy drive types: 720 KB, 1.2 MB,
1.44 MB, 2.88 MB, and LS-120.
Connect one side of the 34-pin flat cable to the floppy drive and plug the
other end to the floppy drive connector on the Motherboard.
This Motherboard can support up to 2 floppy drives.
1
1
33
33
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3.3 Front Panel Connections
HDD
LED
Speaker
_
PWRBT
Reset
Power /
ACPI
LED
+
RTL8139C
VT1611A
3V
Lithium
Battery
Plug the computer case's front panel devices to the corresponding headers
on the Motherboard.
1. Power LED
Please install according to the following pin assignment: pin 1,3 are for
Power LED.
Power LED
Pin Assignment
_
+
Control
NC
GND
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2. Reset
Plug the Reset push-button cable into the 2-pin Reset header on the
Motherboard. Pushing the Reset button on the front panel will cause the
system to restart the boot-up sequence.
PWRBT Pin Assignment
1
Control
GND
3. Speaker
Attach the 4-pin PC speaker cable from the case to the Speaker header on
the Motherboard.
Speaker Pin Assignment
_
+
Speaker out
+5V
NC NC
4. IDE LED
Attach the 2-pin IDE device LED cable to the corresponding IDE LED
header on the Motherboard. This will cause the LED to light up when an
IDE (HDD, CD-ROM) device is active.
HDD LED Pin Assignment
_
+
LED Anode LED Cathode
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
5. ATX Power On/Off Switch
Attach the 2-pin momentary type switch to the PWRBT header for turning
On or Off your ATX power supply.
PWRBT Pin Assignment
1
Power On/Off
GND
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3.4 Back Panel Connections
All external devices such as the PS/2 keyboard, PS/2 mouse, printer,
modem, USB can be plugged directly onto the Motherboard back panel.
Only after you have fixed and locked the Motherboard to the computer
case can you start connecting the external peripheral devices.
When connecting an external device, use the following figure to locate and
identify which back panel connector to plug the device to.
PS/2 KB
PS/2 Mouse
Connector
COM 1
VGA
RTL8139C
USB 1_2
VT1611A
JOYSTICK
LINE-OUT
3V
Lithium
Battery
LINE-IN
MIC JACK
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
1. Onboard Serial Ports COM1
External peripherals that use serial transmission scheme include:
-
-
serial mouse,
and modem.
Plug the serial device cables directly into the COM1 9-pin male
connectors located at the rear panel of the Motherboard.
2. Parallel Port PRT
This parallel port is used to connect the printer or other parallel devices.
Plug the parallel device cable into the 25-pin female connector located at
the rear panel of the Motherboard.
3. PS/2 Keyboard
Plug the keyboard jack directly into the 6-pin female PS/2 keyboard
connector located at the rear panel of the Motherboard.
Pin5
KBD Clock
Pin6
NC
Pin4
VCC
Pin3
GND
Pin1
KBD DATA
Pin2
NC
4. PS/2 Mouse
Similarly, plug the mouse jack directly into the 6-pin female PS/2 mouse
connector.
Pin5
Mouse Clock
Pin6
NC
Pin4
VCC
Pin3
GND
Pin1
Mouse DATA
Pin2
NC
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
5. Universal Serial Bus USB3/USB4
This Motherboard provides four USB ports for your additional devices.
Plug the USB device jack into the available USB connector USB3 or
USB4.
-
Standard device drivers come with the Win98 for commonly used
USB devices.
-
With Win95, use the flow UHCI specifications. To use USB devices
under Win95, usually you have to install the device that driver comes
with the USB device you have purchased.
6. Onboard Game port/audio
This Motherboard provides Game port and audio.
-
-
Attach the Game cable to the 15-pin Game port at the rear panel of
you motherboard.
This Motherboard features three built-in audio-stereo ports (labeled
line-in, line-out, and mic jack) convenient to directly plug-in all your
external audio devices.
7. VGA monitor connector
Plug the monitor cable into the 15-pin female VGA connector located at
the real panel of the motherboard.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3.5 Other Connections
1. Wake-On-LAN (WOL)
Attach the 3-pin connector from the LAN card which supports the
Wake-On-LAN (WOL) function to the JP44 header on the Motherboard.
This WOL function lets users wake up the connected computer through the
LAN card.
Please install according to the following pin assignment:
Wake-On-LAN
JP44 Pin Assignment
1 2 3
5VSB
GND
Wakeup
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2. Infrared (SIRCON1)
Plug the 5-pin infrared device cable to the SIRCON1 header. This will
enable the infrared transfer function. This Motherboard meets both the
ASKIR and HPSIR specifications.
Please install according to the following pin assignment:
Standard Infrared
(SIRCON1) Connector
SIRCON Pin Assignment
3
5
1 2
4
VCC
IRTX
IRRX
GND
3. Other Display Cards
Insert other types of VGA cards into the PCI or ISA expansion slots
according to card specifications.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
4. Cooling Fan Installation
(1) CPU Cooling Fan
After you have seated the CPU properly on the processor, attach the 3-pin
fan cable to the CPUFAN connector on the Motherboard. The fan will stop
when the system enters into Suspend Mode. (Suspend mode can be
enabled from the BIOS Setup Utility, [POWER MANAGEMENT] menu.)
To avoid damage to the system, install according to the following pin
assignment:
CPU Cooling Fan
CPUFAN1 Pin Assignment
SENSOR
12V
3
2
1
GND
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
(2) Chipset Cooling Fan
Some chipset also feature a cooling fan. This Motherboard features a
CHIPFAN connector to provide 12V power to the chipset fan. Connect the
cable from the chipset fan to the CHIPFAN 3-pin connector. Install
according to the following pin assignment:
Chipset Cooling Fan
CHIPFAN Pin Assignment
1
2
3
GND
12V
NC
Note: CPUFAN must be installed for this Motherboard, CHIPFAN is
optional.
5. CD Line-in (CDIN1)
This Motherboard provides two CD-Line in connectors. Please connect the
4-pin audio cable from your CD-ROM drive to either CDIN1. (It fits in
only one, depending on the cable that came with your CD-ROM drive)
Please install according to the following pin assignment:
CD-IN: CDIN1
1
2
3
4
Left
GND
Right
GND
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.3.6 ATX Power Supply
Plug the connector from the power directly into the 20-pin male ATX PW
connector on the Motherboard, as shown in the following figure.
ATX Power
RTL8139C
VT1611A
3V
Lithium
Battery
Warning: Follow these precautions to preserve your
Motherboard from any remnant currents when connecting to
ATX power supply:
Turn off the power supply and unplug the power cord of the
ATX power supply before connecting to ATX PW connector.
The Motherboard requires a power supply with at least 200 Watts and a
"power good" signal. Make sure the ATX power supply can take at least
720 mA * load on the 5V Standby lead (5VSB) to meet the standard ATX
specification.
* Note: If you use the Wake-On-LAN (WOL) function, make sure the
ATX power supply can support at least 720 mA on the 5V Standby lead
(5VSB).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
Please install the ATX power according to the following pin assignment:
ATX Power
12V
5VSB
PW-OK
GND
5V
5V
5V
-5V
GND
GND
GND
PS-ON
GND
-12V
3.3V
GND
5V
ꢀ Pay special care to the directionality.
GND
3.3V
3.3V
2-3.4 CPU FSB Setting (JP3)
Refer to the following table:
CPU FSB Setting
200MHz(Default)
JP3
Short Pin2-3
1 2
3
Short Pin1-2
266MHz
1 2
3
2-3.5 CMOS Clearing (JP5)
After you have turned off your computer, clear the CMOS memory by
momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then
restore JP5 to the initial 1-2 jumper setting in order to recover and retain
the default settings.
Jumper JP5 can be easily identified by its white colored cap.
CMOS
Clearing
Clear CMOS Data
Retain CMOS Data
Short pin 2-3 for
at least 5 seconds to
clear the CMOS
Short pin 1-2
to retain new
settings
JP5 Setting
1 2 3
1 2 3
Note: You must unplug the ATX power cable from the ATX power
connector when performing the CMOS Clear operation.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.6 Power On
You have now completed the hardware installation of your Motherboard
successfully.
1. Turn the power on
2. To enter the BIOS Setup Utility, press the <DEL> key while the system
is performing the diagnostic checks,
Note: If you have failed to enter the BIOS, wait until the boot up
sequence is completed. Then push the RESET button and press
<DEL> key again at the beginning of boot-up, during diagnostic
checks.
Repeat this operation until you get the following screen.
3. The BIOS Setup screen appears:
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀ Standard CMOS Features
ꢀ Advanced BIOS Features
ꢀ Advanced Chipset Features
ꢀ Integrated Peripherals
ꢀ Power Management Setup
ꢀ PnP/PCI Configurations
ꢀ PC Health Status
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
Esc : Quit
ꢄꢅꢆꢇ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.7 Quick BIOS Setup
After the hardware installation is complete, turn the power switch on, then
press the <DEL> key during the system diagnostic checks to enter the
Award BIOS Setup program. The CMOS SETUP UTILITY will display
on screen. Follow these steps to configure the CPU settings.
Step 1. Select [STANDARD CMOS Features]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to
“Auto”.
Step 2. Select [LOAD Optimized DEFAULTS]
Select the “LOAD Optimized DEFAULTS” menu and type “Y” at the
prompt to load the BIOS optimal setup.
Step 3. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and
continue the boot sequence.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
2-3.8 Troubleshooting at First Start
Video (no display) related issues
I built a new computer system using a Soyo board and nothing
happens when turning it on, no video and no beeps from the PC
speaker. What is happening and how can it be fixed?
No screen and no beep means that your CPU and motherboard do not
work at all. It could be that the CPU is not seated correctly or that a
component on the M/B is grounded (shorted) with the case. Also make
sure to check the voltage setting switch (110V/220V) on the back of the
power supply. To isolate the problem do the following:
1. Press and hold down on the “Ins” (insert) key while turning on the
computer until you get video. If you do not get video then,
2. Remove all add-on cards, unplug all hard-disk and floppy-disk drive
cables and see if you can hear some beeps. If you still do not get any beeps,
then try putting the motherboard on the table (to isolate it from the case)
with the CPU and speaker only, and give it one more try.
I hear a series of beeps and I do not get anything from my monitor.
What could be wrong?
Continuous beeps – One or more of the memory modules is not seated
correctly in its socket.
BIOS Issues
Where can I find the BIOS revision of my mainboard?
It will be displayed on the up-left corner on the screen during boot-up. It
will show as your board type followed by the revision number, such as
5EH_2CA1 (meaning revision 2CA1 for the SY-5EH board) or 6BA+
IV_2AA2 which means SY-6BA+ IV motherboard with 2AA2 bios.
Where can I find the latest BIOS of my motherboard?
Please go to the technical support page of one of the SOYO websites
the latest BIOS revision.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
Hard disk, floppy drive, CD-ROM etc
When I boot up my new computer I got "floppy boot failure" and the
LED on the floppy stays on
Make sure the red wire of floppy ribbon cable goes to Pin1 on the floppy
drive side (don't trust the "key lock" or "notch") and use the end-connector
of the cable (don't use middle one).
Modem issues
I have installed my modem drivers several times and I still cannot get
my modem to work. Why?
If you are sure that the modem driver has been installed correctly, then you
need to install the via 4 in 1 driver from the SOYO CD, this is because
Windows does not properly recognize relatively new chipsets.
Audio Issues
I do not get any sound from onboard audio. What could be wrong?
Please make sure the speaker is connected to the speaker out port on your
sound card.
In Device Manager, I keep getting yellow exclamation signs on my
sound port even though I have installed my sound driver several times
and I could not get my sound card to work. What is wrong?
It is likely that you did not have the correct driver installed. If you are sure
that the correct sound driver has been installed, then please install the 'via
4 in 1' driver for the motherboard.
The sound is working in my system, but when I play CD music from
the CD-ROM, I do not get any sound. What is wrong?
This is because the 3-wire audio cable from the CD-ROM to the sound
card is not connected or it is loose.
The sound and everything else works fine except that the recorder and
microphone do not work. What is wrong?
This is because the recorder and microphone in the Windows are not
enabled. Please go to sound properties and enable them.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
SY-K7VEMPRO
Lock up (freeze)
When I boot up my system, everything works fine. It sees my CPU
and memory, detects my hard drive, floppy drive and CD-ROM but
locks up at "Verify DMI pool data... ", and it won’t go any further.
What should I do?
Please clear the CMOS via JP5 then choose 'load optimized default' in the
bios and save the bios and exit. Next, unplug all other add-on cards except
the video card and floppy drive controller, and see if it can boot from
floppy. Then put back the peripherals one by one to identify which one
causes the lockup.
I can not get my board to run properly.
Please make sure you have the latest bios and driver from the SOYO web
site at: http://www.soyo.com
2-3.9 Power Off
There are two possible ways to turn off the system:
1. Use the Shutdown command in the Start Menu of Windows 95/98
to turn off your computer.
2. Press the mechanical power-button and hold down for over 4
seconds, to shutdown the computer. If you press the power-button for
less than 4 seconds, then your system will enter into Suspend Mode.
You are now ready to configure your system with the BIOS setup program.
Go to Chapter 3: BIOS SETUP
46
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Chapter 3
BIOS SETUP UTILITY
This Motherboard's BIOS setup program uses the Phoenixnet BIOS
program from Award Software Inc.
To enter the Award BIOS program's Main Menu:
1. Turn on or reboot the system.
2. After the diagnostic checks, press the [Del] key to enter the Award
BIOS Setup Utility.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Peripherals
ꢀPower Management Setup
ꢀPnP/PCI Configurations
ꢀPC Health Status
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
Esc : Quit
ꢄꢅꢆꢇ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Selecting items
ꢃ
ꢃ
Use the arrow keys to move between items and select fields.
From the Main Menu press arrow keys to enter the selected submenu.
Modifying selected items
ꢃ
Use the [Up]/[Down] keys to modify values within the selected fields.
Some fields let you enter values directly.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Hot Keys: Function keys give you access to a group of commands
throughout the BIOS utility.
Function Command
Description
Gives the list of options available for each
item.
F1
General Help
Previous
Values
Restore the old values. These are the values
that the user started the current session with.
F5
Load
Loads all items with the most conservative
values.
F6
F7
Fail-Safe
Defaults
Load
Optimized
Defaults
Save
Loads all options with the optimize values.
F10
Saves your changes and reboots the system.
Returns at anytime and from any location to
the Main Menu.
[Esc]
Exit
Will display a overlapping window with all
options for the current item.
[Enter]
Select
Using the +, –, Page Up and Page Down
keys the user can toggle the value of the
current item.
[+/–/PU/PD] Value
48
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
SAVE AND EXIT SETUP
Select the [SAVE & EXIT SETUP] option from the Main Menu to save
data to CMOS and exit the setup utility. This option saves all your changes
and causes the system to reboot.
R
O
O
M
S
P
C
I / I S
A
B
I O
I L I T
I N
S
C
M
S
E
T
U
T
P
U
T
Y
Type [Y] to save the
changes and exit or [N]
to return to the Main
Menu and keep current
values.
A
W
A
R
D
S
O
F
W
A
R
E
,
C
.
T
S
B
C
P
P
L
T
A
N
D
F
A
E
R
D
C
M
O
S
S
E
T
U
P
I N
T
E
G
R
A
E
D
P
E
R
I P
H
E
R
A
L
S
I O
H
S
I P
W
P
S
E
O
E
/ P
D
R
C
S
B
SAVE to CMOS and EXIT
N
O
A
L
O
A
D
I O
S
D
E
F
A
U
L
T
S
E
F
s
c
:
:
Q
S
u
i t
↑
↓
h
→
←
:
:
S
C
e
h
l e
a
c
t
I t e
m
o
1
0
a
v
e
&
E
x
i t
S
e
t
u
p
( S
D
i f t )
F
2
n
g
e
C
l o
r
T
i m
e
,
D
a
t e
,
H
a
r d
i s
k
T
y
p
e
…
EXIT WITHOUT SAVING
Selecting the [EXIT WITHOUT SAVING] option allows you to abandon
all data and exit setup, therefore ignoring all your changes.
R
O
O
M
S
P
C
I / I S
A
B
I O
I L I T
I N
S
C
M
S
E
T
U
T
P
U
T
Y
A
W
A
R
D
S
O
F
W
A
R
E
,
C
.
T
Type [Y] to abandon
changes and exit or [N]
to return to the Main
Menu and keep current
values.
S
B
C
P
P
L
T
A
N
D
F
A
E
R
A
D
C
M
E
O
S
S
S
E
T
U
P
P
I N
S
T
E
G
R
A
E
D
P
E
R
I P
S
H
E
R
A
L
S
I O
H
S
T
U
R
S
E
T
U
U
P
E
R
V
I S
O
R
P
A
S
W
O
R
D
I
W
P
O
N
Quit Without Saving (Y/N)? _
O
A
A
L
O
E
F
s
c
:
:
Q
S
u
i t
↑
↓
h
→
←
:
:
S
e
h
le
a
c
t
I t e
m
1
0
a
v
e
&
E
x
i t
S
e
t u
p
( S
D
if t )
F
2
C
n
g
e
C
o
l o
r
T
im
e
,
D
a
t e
,
H
a
r d
i s
k
T
y
p
e
…
49
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-1 STANDARD CMOS SETUP
Select the [STANDARD CMOS SETUP] option from the Main Menu and
press [Enter] key.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Fri, Jan 1 2000
1 : 22 : 12
Item Help
Menu Level
ꢀ
ꢀ IDE Primary Master
ꢀ IDE Primary Slave
ꢀ IDE Secondary Master
ꢀ IDE Secondary Slave
None
None
None
None
Drive A
Drive B
1.44M, 3.5 in.
None
Floppy 3 Mode Support
Disabled
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
Total Memory
640K
30720K
31744K
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
This screen allows you to modify the basic CMOS settings.
After you have completed the changes, press [Esc] key to return to the
Main Menu.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
This Main Menu function automatically detects the hard disk type and
configures the [Standard CMOS Features] accordingly.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
IDE Primary Master
IDE HDD Auto-Detection
IDE Primary Master
Press Enter
Auto
Item Help
Menu Level
ꢀ
Capacity
0 MB
Access Mode
Auto
0
0
0
0
0
Cylinder
Head
Precomp
Landing Zone
Sector
0
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
Note: This function is only valid for IDE type of hard disk drives.
3-1.1 Date & Time
Display
Setting
Please Note
mm/dd/yyyy Type the current date
You can also the
PUp/PDn keys to toggle
Date
hh:mm:ss
Type the current time 24-hour clock format
3:15 PM is displayed as
Time
15:15:00
51
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-1.2 Hard Disks Type & Mode
Choose the type and mode for the hard disks that you have already
installed.
Primary
Setting
Description
Note
(Secondary)
Master & Slave
Press
To auto-detect the HDD’s size,
head… on this channel
IDE HDD
Auto-Detection Enter
Auto
BIOS detects hard disk type
automatically.
User defines the type of hard disk.
Default
Default
IDE Primary
Slave
(User Type)
User
None
Auto
BIOS detects hard disk mode
automatically.
Access Mode
Normal Normal IDE hard disk
<528MB
>528MB
LBA
Enhanced IDE hard disk
Large IDE hard disk (for certain
hard disk)
Large
Note: If you have any questions on your hard disk type or mode, ask
your hard disk provider or previous user for details.
3-1.3 Floppy Drives
Floppy Drives
Setting
Description
Note
360KB, 5.25 in.
1.2MB, 5.25 in.
720KB, 3.5 in.
1.44MB, 3.5 in.
2.88MB, 3.5 in.
None
Drives A & B
Default
Not installed
Disabled
Drive A
Drive B
Both
Default
Floppy 3-Mode
Support
Supports 3-mode
floppy diskette:
740KB/1.2MB/
1.44MB on selected
disk drive.
Special disk drive
commonly used in
Japan
52
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-1.4 Others Optional
Setting
Description
Note
EGA/VGA
CGA 40
Select the video mode.
Default
Video
CGA 80
MONO
(Monochrome)
ALL Errors
No Errors
All, But Keyboard
All, But Diskette
All, But Disk/Key
When the BIOS detects system Default
errors, this function will stop the
system. Select which type of
Halt On
error will cause the system halt.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-2 ADVANCED BIOS FEATURES
Select the [Advanced BIOS Features] option from the Main Menu and
press [Enter] key.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Advanced BIOS Features
Virus Warning
CPU Internal Cache
External Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Disabled
Enabled
Enabled
Enabled
Floppy
HDD-0
LS120
Enabled
Disabled
Enabled
On
Item Help
Menu Level
ꢀ
Fast
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
Disabled
6
250
Setup
OS Select For DRAM > 64MB Non-OS2
Video BIOS Shadow
Enabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
LOGO-0
Enabled
C8000-CBFFF Shadow
CC000-CFFFF Shadow
D0000-D3FFF Shadow
D4000-D7FFF Shadow
D8000-DBFFF Shadow
DC000-DFFFF Shadow
EPA LOGO SELECT
Small Logo (EPA) Show
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
After you have completed the changes, press [Esc] key and follow the
instructions on your screen to save your settings or exit without saving.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Description Note
3-2.1 Virus Warning
Setting
Disabled If set to enabled, the Paragon Default
Virus Protection
Anti-Virus. Function will scan
your boot drive for boot
virusses. If a boot virus is
detected, the BIOS will display
a warning message.
Enabled
3-2.2 Cache Memory Options
Setting
Description
Note
Disabled
CPU Internal Cache
Enabled Enables the CPU's internal Default
cache.
External Cache
Disabled
Enabled Enables the external
memory.
Default
3-2.3 Quick Power On Self Test
Setting
Description
Note
Quick Power Enabled Provides a fast POST at boot-up. Default
On Self Test
Disabled
55
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-2.4 System Boot Control Settings
System Boot
Setting
Description
Note
Control Settings
Floppy
HDD-0
LS/ZIP
SCSI
Select Your Boot Device
Priority
First
/Second/Third
Boot Device
CDROM
HDD-1
HDD-2
HDD-3
LAN
Disabled
Boot Other
Device
Disabled
Enabled
Select Your Boot Device
Priority
Default
AC97
Audio/Modem
Disabled
This item allows you to
decide to auto/disable the
810 chipset family to
support AC97 Audio/
Modem.
3-2.5 Floppy Driver Settings
Setting
Description
Note
Disabled
Enabled
Default
Swap Floppy
Drive
Changes the sequence of A and B
drives.
3-2.6 Boot Up Floppy Seek
Setting
Description
Note
Disabled Seeks disk drives during boot up.
Disabling speeds boot up.
Enabled
Boot Up Floppy
Seek
Default
3-2.7 Boot Up NumLock Status
Setting
Description
Note
56
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
Setting
SY-K7VEMPRO
Description
Note
Boot Up
NumLock
Status
On
Puts numeric keypad in
Default
NumLock mode at boot-up.
Puts numeric keypad in arrow key
mode at boot-up.
Off
3-2.8 Gate A20 Options
Setting
Description
Note
Normal
Fast
Lets chipset control GateA20.
A pin in the keyboard controller Default
controls GateA20.
Gate A20
Options
3-2.9 Typematic Settings
Typematic Settings Setting
Description
Note
Disabled
Enabled
Keystrokes repeat at a rate Default
determined by the
keyboard.
When enables , the
typematic rate and
typematic delay can be
selected.
Typematic
Rate Setting
The following [Typematic Rate] and [Typematic Delay] fields are active
only if [Typematic Rate Setting] is set to [Enabled]
6 (Char/sec)
8 (Char/sec)
10 (Char/sec)
12 (Char/sec)
15 (Char/sec)
20 (Char/sec)
24 (Char/sec)
30 (Char/sec)
Choose the rate at which a Default
character is repeated when
holding down a key.
Typematic Rate
250 (msec)
500 (msec)
750 (msec)
1000 (msec)
Typematic Delay
Choose how long after
you press a key down the
character begins
Default
repeating.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-2.10 Security Option
Use this feature to prevent unauthorized system boot-up or use of BIOS
Setup. The following table describes the security settings.
Setting
Description
System Each time the system is booted, the
password prompt appears.
Security Option
Setup
If a password is set, the password prompt
only appears when you attempt to enter the
BIOS Setup program.
3-2.11 Other Control Options
Other Control Setting
Options
Description
Note
OS Select for
DRAM>64MB
OS2
When using an OS2 operating
system.
Non-OS2 When using another,
non-OS2 operating system.
Default
Default
Video BIOS
Shadow
Disabled
Enabled
The BIOS is shadowed in a 16K segment if it
is enabled and if it has BIOS present.
These 16 segments can be shadowed from
ROM to RAM. BIOS shadow copies BIOS
code from slower ROM to faster RAM. BIOS
can then execute from RAM.
LOGO-0 Allows user to display SOYO
Default
Default
EPA LOGO
SELECT
logo or own logo.
LOGO-1
Logo-0 Shows SOYO logo.
Logo-1 Shows user logo (Default
Blank).
Disabled Set Enabled to show small Logo
Small Logo
(EPA) Show
(EPA).
Enabled
58
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-3 ADVANCED CHIPSET FEATURES
Caution: Change these settings only if you are already familiar
with the Chipset.
The [Advanced Chipset Features] option changes the values of the chipset
registers. These registers control the system options in the computer.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Advanced Chipset Features
ꢁ
DRAM Timing By SPD
x DRAM Clock
x SDRAM Cycle Length
Enabled
133M
3
Item Help
Menu Level
ꢀ
x Bank Interleave
Memory Hole
Disabled
Disabled
PCI Master Pipeline Req
P2C/C2P Concurrency
Enabled
Disabled
Fast R-W Turn Around
System BIOS Cacheable
Disabled
Disabled
Video RAM Cacheable
AGP Aperture Size
Disabled
64M
AGP Mode
4X
AGP Driving Control
x AGP Driving Value
OnChip USB
Auto
DA
Enabled
OnBoard LAN
Enabled
Disabled
USB Keyboard Support
OnChip Sound
Auto
CPU to PCI Write Buffer
PCI Dynamic Bursting
Enabled
Enabled
PCI Master 0 WS Write
PCI Delay Transaction
PCI#2 Access #1 Retry
AGP Master 1 WS Write
AGP Master 1 WS Read
Enabled
Disabled
Enabled
Disabled
Disabled
ꢂ
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
59
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
After you have completed the changes, press [Esc] and follow the
instructions on your screen to save your settings or exit without saving.
The following table describes each field in the Advanced Chipset Features
Menu and how to configure each parameter.
3-3.1 CHIPSET FEATURES SETUP
CHIPSET
Setting
Description
Note
FEATURES
Enabled
Disabled
If enable the DRAM will auto
detect the DRAM timing.
Default
DRAM
Timing By
SPD
133M
This item allows you to control the default
DRAM speed.
DRAM Clock
SDRAM Cycle
Length
3
2
Default
When synchronous DRAM is
installed, the number of clock
cycles of CAS latency depends on
the DRAM timing. Do not reset
this field from the default value
specified by the system designer.
4 Bank
Disabled
2 Bank
Bank
Interleave
Increase DRAM performance.
Default
PCI Master
Pipeline Req
Disabled
Enabled
Disabled/Enabled PCI Master
Pipeline Req.
Default
Default
Memory Hole Disabled
15M – 16M Some interface cards will map
their ROM address to this area. If
this occurs, select [Enabled] in this
field.
Disabled
Enabled
This item allows you to
enable/disable the PCI to CPU,
CPU to PCI concurrency
Default
P2C/C2P
Concurrency
60
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
CHIPSET
Setting
Description
FEATURES
Fast R-W
Turn Around
This item controls the DRAM
timing. It allows you to enable/
disable the fast read/write turn
around.
Disabled
Enabled
Default
System BIOS Disabled
Default
Default
Cacheable
Enabled
The ROM area F0000H-FFFFFH
is cacheable.
Disabled
Enabled
When synchronous DRAM is
installed, the number of clock
cycles of CAS latency depends on
the DRAM timing. Do not reset
this field from the default value
specified by the system designer
Video RAM
Cacheable
64M
Select the size of Accelerated
Graphics Port (AGP) aperture. The
aperture is a portion of the PCI
memory address range dedicated
for graphics memory address
space. Host cycles that hit the
aperture range are forwarded to the
AGP without any translation.
Default
AGPAperture
Size
4M, 8M,
16M, 32M,
128M.
4x
2x
1x
This item allows you to select the Default
AGP Mode.
AGP Mode
Auto
Manual
This item allows you to adjust the Default
AGP driving force. Choose
Manual to key in a AGP Driving
Value in the next selection. This
field is recommended to set in
Auto for avoiding any error in your
system.
AGP driving
Control
AGP driving Min=0000~ This item allows you to adjust the
Value
Max=00FF AGP driving force.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
CHIPSET
Setting
Description
FEATURES
This should be enabled if your
system has a USB installed on the
system board and you want to use
it. Even when so equipped, if you
add a higher performance
OnChip USB
Disabled
Enabled
Default
Default
controller, you will need to disable
this feature.
Disabled
Enabled
USB
Keyboard
Support
Select Enabled if your system
contains a Universal Serial Bus
(USB) controller and you have a
USB keyboard.
On Chip
Sound
Auto
Disabled
This item allows you to control the Default
onboard AC 97 audio.
On Board
LAN
Enabled
Disabled
Enabled/Disabled Onboard H/W Default
LAN.
CPU to PCI
Write Buffer
Disabled
Enabled
When this field is Enabled, writes
from the CPU to the PCI bus are
Default
buffered, to compensate for the
speed differences between the CPU
and the PCI bus. When Disabled,
the writes are not buffered and the
CPU must wait until the write is
complete before starting another
write cycle.
Disabled
Enabled
When Enabled, every write
transaction goes to the write buffer.
Default
Burstable transactions then burst
on the PCI bus and nonburstable
transactions don’t.
PCI Dynmic
Bursting
PCI Master 0 Disabled
62
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
CHIPSET
FEATURES
WS Write
Setting
Description
Enabled
When Enabled, writes to the PCI Default
bus are executed with zero wait
states.
Disabled
Enabled
The chipset has an embedded
32-bit posted write buffer to
support delay transactions cycles.
Select Enabled to support
compliance with PCI specification
version 2.1.
Default
PCI Delay
Transaction
Disabled
Enabled
When disabled, PCI#2 will not be
disconnected until access finishes
(difault). When enabled, PCI#2
will be disconnected if max retries
are attempted without success.
PCI#2 Access
#1 Retry
Default
Default
Disabled
Enabled
AGP Master 1
WS Write
When Enabled, writes to the
AGP(Accelerated Graphics Port)
are executed with one wait states.
AGP Master 1 Disabled
WS Read
Default
Enabled
When Enabled, read to the AGP
(Accelerated Graphics Port) are
executed with one wait states.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-4 INTEGRATED PERIPHERALS
Caution: Change these settings only if you are already familiar
with the Chipset.
The [INTEGRATED PERIPHERALS] option changes the values of the
chipset registers. These registers control the system options in the computer.
The following screen shows setup default settings.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Integrated Peripherals
ꢁ
OnChip IDE Channel0
OnChip IDE Channel1
IDE Prefetch Mode
Enabled
Enabled
Enabled
Auto
Item Help
Menu Level
ꢀ
Primary Master PIO
Primary Slave
PIO
Auto
Secondary Master PIO
Secondary Slave PIO
Primary Master UDMA
Auto
Auto
Auto
Primary Slave
UDMA
Auto
Secondary Master UDMA
Secondary Slave UDMA
Init Display First
Auto
Auto
AGP
IDE HDD Block Mode
Onboard FDD Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART 2 Mode
x IR Function Duplex
x TX,RX inverting enable
Onboard Parallel Port
Onboard Parallel Mode
x ECP Mode Use DMA
x Parallel Port EPP Type
Onboard Legacy Audio
Sound Blaster
Enabled
Enabled
3F8/IRQ4
2F8/IRQ3
Standard
Half
No, Yes
378/IRQ7
Normal
3
EPP1.9
Enabled
Disabled
220H
SB I/O Base Address
SB IRQ Select
IRQ 5
SB DMA Select
MPU-401
MPU-401 I/O Address
Game Port (200-207H)
DMA 1
Disabled
330-333H
Enabled
ꢂ
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
64
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
The following tables describe each field in the INTEGRATED
PERIPHERALS Menu and provide instructions on how to configure the
IDE controls, FDC controls, and the onboard serial and parallel ports.
3-4.1 IDE Device Controls
IDE Controls
Setting
Description
Note
Disabled
Turn off the on-board
IDE
On-Chip PCI IDE
ꢀ Primary
ꢀ Secondary
Enabled
Use the on-board IDE
Default
IDE
mode 0-4
0 is the slowest speed
4 is the fastest speed
ꢀ
ꢀ
ꢀ
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Auto
For better performance Default
and stability, we suggest
you use the Auto setting
to set the HDD control
timing.
ꢀ
Secondary Slave PIO
Disabled
Auto
IDE
ꢀPrimary Master UDMA
ꢀPrimary Slave UDMA
ꢀSecondary Master UDMA
ꢀSecondary Slave UDMA
Select Auto to enable
Ultra DMA Mode
support.
Default
3-4.2 Display Controls
Display Controls Setting Description
Note
PCI Slot Choose which card – AGP
Default
Init Display First
Display card or PCI VGA card –
to initialize first.
AGP
3-4.3 IDE HDD Block Mode
Setting
Description
Note
Disabled
Enabled
IDE HDD Block Mode
Invokes multi-sector
transfer instead of one
sector per transfer. Not
all HDDs support this
function.
Default
65
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
3-4.4 FDC Controls
FDC Controls
Setting
Description
Disabled
Turn off the on-board
floppy controller
Onboard FDD
controller
Enabled
Use the on-board floppy Default
controller
3-4.5 Onboard Serial Ports
Onboard Serial Setting
Ports
Description
Note
Disabled
Onboard
Serial Port 1 /
Serial Port 2
3F8/IRQ4
Choose serial port 1 & 2's I/O Default
address.
(port 1)
Default
(port 2)
Do not set port 1 & 2 to the
same address except for
Disabled or Auto.
2F8/IRQ3
3E8/IRQ4
2E8/IRQ3
Auto
UART 2 Mode Standard
The second serial port offers Default
these InfraRed interface
modes.
HPSIR
ASKIR
If [UART 2 Mode] is set to [HPSIR]/[ASKIR]
IR Function
Duplex
Half
Full
Choose [Half] or [Duplex] to Default
set UR2 in half duplex mode
or full duplex mode
respectively. Refer to your IR
device specifications to select
the suitable mode.
TX,RX inverting No,Yes
This item allow you to enable Default
the TX, RX inverting which
depends on different H/W
requirement. This field is not
recommended to change its
default setting for avoiding
any error in your system
enable
No, No/
Yes, No/
Yes, Yes.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
3-4.6 Onboard Parallel Ports
Onboard Parallel
Ports
Setting
Description
Disabled
Choose the printer I/O
address.
Onboard Parallel
Port
378/IRQ7
3BC/IRQ7
278/IRQ5
Default
Normal
EPP
ECP
The mode depends on your Default
external device that
connects to this port.
Parallel Port Mode
ECP/EPP
3
1
Choose DMA3
Choose DMA1
Default
Default
ECP Mode use
DMA
If [Parallel Port Mode] is set to [EPP] mode
Parallel Port EPP
TYPE
EPP 1.9
EPP 1.7
Select EPP port type 1.9
Select EPP port type 1.7
3-4.7 Onboard Legacy Audio
This field controls the onboard legacy audio.
Setting Description
Note
Onboard
Disabled Set this item to Enabled if using
software (like DOS games) that needs
a ‘legacy’ audio device.
Legacy Audio
Enabled
Default
Default
Disabled Set this item to enabled if your
Sound Blaster
on-board audio-chip is sound Blaster
compatible.
Enabled
220H
240H
260H
280H
Select the base address for your
sound Blaster (SB) compatible Audio
IC.
Default
Default
SB I/O Base
Address
IRQ 5
IRQ 7
IRQ 9
IRQ 10
Select the IRQ your SB Audio IC
uses.
SB IRQ Select
67
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
DMA1
SY-K7VEMPRO
Default
Select the DMA channel your SB
Audio IC uses.
SB DMA Select
DMA0
DMA2
DMA3
Onboard Legacy Audio (Continued)
This field controls the onboard legacy audio.
Setting Description
Note
Disabled Set this item to enabled to make use Default
of MIDI.
MPU-401
Enabled
MPU-401 I/O 330-333H Select the I/O address for your MIDI Default
Address
functionality.
300-303H
310-313H
320-323H
Disabled Set this item to enabled to make use
of the game port.
Enabled
Game Port
(200-207H)
Default
68
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-5 POWER MANAGEMENT SETUP
The [POWER MANAGEMENT SETUP] sets the system's power saving
functions.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Power Management Setup
Power Management
ACPI Suspend Type
Video Off Option
Video Off Method
MODEM Use IRQ
Soft-Off by PWRBTN
Wake Up Events
Press Enter
S1 (POS)
Suspend -> Off
V/H SYNC+Blank
3
Item Help
Menu Level
ꢀ
Instant-Off
Press Enter
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
Wake Up Events
VGA
OFF
Item Help
LPT & COM
HDD & FDD
LPT/COM
ON
Menu Level
ꢀ
PCI Master
OFF
Wake Up On LAN/Ring
RTC Alarm Resume
x Date (of Month)
x Resume Time (hh:mm:ss)
Primary INTR
Disabled
Disabled
0
0
:
1
:
2
ON
IRQs Activity Monitoring
Press Enter
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
69
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
After you have completed the Power Management Setup, press [Esc] to
return to the Main Menu.
3-5.1 Power Management Controls
Power
Setting
Description
Note
Management
Controls
S1(POS)
S3(STR)
The system will enter the S1
state during suspend. (Low
latency wake up)
Default
Default
ACPI Suspend
Type
Video Off
Option
Suspend --> When enabled, this feature
Off
allows the VGA adapter to
operate in a power saving mode.
Always On
All Modes
--> Off
Video Off
Method
V/H
Selects the method by which the Default
Sync+Blank monitor is blanked.
Blank screen
DPMS
70
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
Power Management Controls (Continued)
Power
Setting
Description
Management
Controls
3
Assigns an IRQ# to the modem Default
device.
MODEM Use
IRQ
3-11, NA
Instant-off
Default
Soft-Off by
PWR-BTTN
Delay 4 Sec. Turns off the system power 4
seconds after pushing the power
button.
Press Enter Select items that will wake up
your system when in one of
Wake Up
Events
sleep modes. Press enter to go
the select item page.
Wake Up
Events
Setting
Description
Note
VGA
OFF
ON
Default
You can set the VGA awakens the
system.
LPT/COM When On of LPT & COM, any
Default
LPT & COM
activity from one of the listed
system peripheral devices or IRQs
wakes up the system.
NONE,
LPT,
COM
OFF
ON
HDD & FDD
PCI Master
When On of HDD & FDD, any
activity from one of the listed
system peripheral devices wakes up
the system.
Default
Default
OFF
ON
When On of PCI Master, any
activity from one of the listed
system peripheral devices wakes up
the system
71
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
Wake Up
Events
Setting
Description
Wake up On Disabled An input signal on the serial Ring Default
Indicator (RI) line (in other words,
an incoming call on the
LAN/Ring
Enabled
modem/LAN) awakens the system
from a soft off state.
Disabled The system ignores the alarm.
Default
Resume by
Alarm
Enabled
Set alarm to power on the system by
the date (1-31) or time (hh:mm:ss).
If the date is set to [0], the system
will self-power on by alarm
everyday at the set time.
Primary INTR ON
When set to On, any event occurring Default
at will awaken a system which has
been powered down.
OFF
Enabled
IRQ3(COM2), IRQ4(COM1),
IRQ5(LPT2), IRQ6(Floppy Disk),
IRQ7(LPT1), IRQ12(PS/2 mouse),
IRQ13(Coprocessor),
IRQs Activity
Monitoring
(Press Enter)
IRQ14(HardDsik)
Disabled IRQ9(IRQ2 Redir),
IRQ10( Reserved),
IRQ11(Reserved)
IRQ8 (RTC Alarm), IRQ15
(Reserved)
72
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-6 PNP/PCI CONFIGURATION SETUP
This option sets the Motherboard's PCI Slots.
CMOS Setup Utility – Copyright ( C ) 1984-2001Award Software
PnP/PCI Configurations
PNP OS Installed
NO
Item Help
Reset Configuration Data
Disabled
Menu Level
ꢀ
Resources Controlled By
x IRQ Resources
Auto (ESCD)
Press Enter
Press Enter
x DMA Resources
PCI/VGA Palette Snoop
Disabled
Assign IRQ For VGA
Assign IRQ For USB
Enabled
Enabled
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
Note: Starred (*) items will disappear when the [Resources
Controlled By] option is set to [Auto].
After you have completed the PCI Slot Configuration, press [Esc] and
follow the instructions on your screen to save your settings or exit without
saving.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
3-6.1 PNP/PCI Configuration Controls
PNP/PCI
Controls
Setting Description
Yes
No
Set this field to [Yes] if you
PnP OS
Installed
are running Windows 95,
which is PnP compatible.
If the OS you are running
does not support PnP
configuration.
Default
(If there is any
doubt, set this
field to [No])
Disabled Retain PnP configuration
data in BIOS.
Enabled Reset PnP configuration data
in BIOS.
Default
Reset
Configuration
Data
Resources
Controlled By
Manual BIOS does not manage PCI/ISA PnP
card IRQ assignment.
Requires to assign IRQ-# and DMA-# to PCI or
ISA PnP manually.
IRQ-3,4,5,7,9,10,11,12,14,15 assigned to: _
DMA-0,1,3,5,6,7 assigned to: _
Auto
The Plug-and-Play BIOS
Recommended
(ESCD) auto manages PCI/ISA PnP
card IRQ assignment
automatically.
If [Resources Controlled By] is set to [Manual]
IRQ/DMA
Resource
PCI/ISA PnP Choose IRQ-# and
DMA-# assigned to
IRQ-3,4,5,7,9,10,
11,12,14,15
PCI/ISA PnP card.
(Press Enter)
DMA-0,1,3,5,6,7
IRQ-3,4,5,7,9,10,
11,12,14,15
Legacy ISA Choose IRQ-# and
DMA-# assigned to
Legacy ISA card.
DMA-0,1,3,5,6,7
Under this item the user can assign an IRQ to a PCI slot. However, there under
some conditions the IRQ will not be assigned as selected under this item:
1. IRQs 0, 1, 2, 6, 8, 13 can NOT be assigned, because they are fixed.
2. IRQs 5, 9, 10, 11 are available
3. IRQs 3,4,7,12,14 and 15 will only be assigned if they are free. See the table
below on how to free them:
74
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
PNP/PCI Configuration Setup (Continued)
PNP/PCI
Setup
Setting
Description
Interrupt How to set the BIOS to release the IRQ to the PnP Interrupt pool:
Line
IRQ 15 IRQ 15: PCI / ISA PnP On-Chip Secondary PCI IDE: disabled
IRQ 14 IRQ 14: PCI / ISA PnP On-Chip Primary PCI IDE: disabled
PnP / PCI configuration
Integrated Peripherals
Interrupt 12 will be released by the PnP
IRQ 12 IRQ 12: PCI / ISA PnP BIOS automatically if the PS/2 Mouse Port
is not used.
IRQ 7
IRQ 4
IRQ 3
IRQ 7: PCI / ISA PnP Onboard parallel port: disabled
IRQ 4: PCI / ISA PnP Onboard Serial port 1: disabled
IRQ 3: PCI / ISA PnP Onboard Serial port 2: disabled
4. Your OS may reassign another interrupt to a PCI slot after BIOS passes control
to the OS, especially if you use Windows 95, 98 or NT.
PCI/VGA
Palette
Disabled Leave this field at Disabled. Default
Enabled
Snoop
Disabled BIOS will assign IRQ for
VGA/USB port.
Assign IRQ
For
VGA/USB
Enabled BIOS won’t assign IRQ for
VGA/USB port.
Default
75
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-6.2 MULTI I/O ADDRESSES
Default settings for multi-I/O addresses are as follows:
Port
I/O Address
378H
IRQ
Status
LPT1
COM1
COM2
7
4
3
ECP/EPP
3F8H
2F8H
Warning: If a default I/O address conflicts with other I/O cards
such as sound card, you must change one of the I/O addresses to
remedy to this address conflict. (I/O addresses can be adjusted from
the BIOS Setup Utility)
3-7 PC HEALTH STATUS
This option sets the Motherboard's PC Health Status.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
PC Health Status
Item Help
Current CPU Temp.
Current System Temp.
Current CPUFAN1 Speed
Vcore
2.5V
3.3V
5V
35 º C / 95 º F
31°C / 87°F
4681 RPM
1.56V
Menu Level
ꢀ
2.47V
3.22V
4.78V
12V
11.58V
FOC (Fan-Off Control)
Enabled
ꢄꢅꢆꢇ:Move
Enter:Select
+/-/PU/PD:Value F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F5:Previous Values
F7: Optimized Defaults
76
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
Note
3-7.1 CPU Device Monitoring
CPU Device
Monitoring
Setting
Description
Current CPU
Temp.
Show the current status of CPU
temperature.
°C/°F
Show the current status of the
system temperature.
Current System
Temp.
°C/°F
RPM
V
Show the current status of CPU
Fan
Current
CPUFAN1
Speed
Show the current voltage status.
Vcore, 2.5V,
3.3V, 5V, 12V
Enabled If enable, this function protect Default
user’s CPU from overheating in
FOC (Fan-Off
Control)
an event there’s a problem with
the CPU FAN. The user should
also plug the CPU FAN power
Disabled
on the CPU FAN1 pin. If not,
system will auto shutdown.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-8 LOAD FAIL-SAFE DEFAULTS
Select the [Load Fail-Safe Defaults] option from the Main Menu to load
the system values you have previously saved. This option is recommended
if you need to reset the system setup and to retrieve the old values.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced Chipset Features
ꢀIntegrated Pe
Load Fail - Safe Defaults
Load Optimized Defaults
Set Supervisor Password
d
Load Fail - Safe Defaults (Y/N)? Y
ꢀPower Mana
ꢀPnP/PCI Configurations
ꢀPC Health Status
p
Exit Without Saving
Esc : Quit
ꢄꢅꢆꢇ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Type [Y] to use the Setup Defaults followed by [Enter] or otherwise [N] to
return to the Main Menu and keep current values.
Warning: If you run into any problem after changing the BIOS
configuration, please load the SETUP DEFAULTS for stable
performance.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-9 LOAD OPTIMIZED DEFAULTS
Select the [Load Optimized Defaults] option from the Main Menu to load
the system values you have previously saved. This option is recommended
if you need to reset the system setup and to retrieve the old values.
CMOS Setup Utility – Copyright ( C ) 1984-2001 Award Software
ꢀStandard CMOS Features
ꢀAdvanced BIOS Features
ꢀAdvanced C
ꢀIntegrated Pe
Load Fail - Safe Defaults
Load Optimized Defaults
sword
d
Load Optimized Defaults (Y/N)? Y
ꢀPower Mana
ꢀPnP/PCI Configurations
ꢀPC Health Status
p
Exit Without Saving
Esc : Quit
ꢄꢅꢆꢇ : Select Item
F10 : Save & Exit Setup
Change CPU’s Clock & Voltage
Type [Y] to use the Setup Defaults followed by [Enter] or otherwise [N] to
return to the Main Menu and keep current values.
Warning: If you run into any problem after changing the BIOS
configuration, please load the SETUP DEFAULTS for stable
performance.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-10 SUPERVISOR PASSWORD
Based on the setting you have made in the [Security Option] of the [BIOS
FEATURES SETUP] section, the password prevents access to the system
or the setup program by unauthorized users. Follow this procedure to set a
new password or disable the password:
1. Choose [BIOS FEATURES SETUP] in the Main Menu and press
[Enter]. Select the [Security Options] item and set the field to:
a. [System]: The password is required every time the system is
booted. This means only a person who knows the password can
use this computer.
b. [Setup]: The password is required only when you attempt to
enter the BIOS Setup program.
2. Choose [SUPERVISOR PASSWORD] from the Main Menu and
press [Enter]. The following prompt appear:
Enter Password:
Warning: If you forget or lose the password, the only way to
access the system is to set jumper JP5 to clear the CMOS RAM.
All setup information is lost and you must run the BIOS setup
program again.
Note: If you do not wish to use the password function, press
[Enter] directly and the following message appears:
Password Disabled!!
80
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3. Enter your new password and press [Enter]. The following message
appears, prompting to confirm the new password:
Confirm Password:
4. Re-enter your password and then press [Enter] to exit to the Main
Menu.
This diagram outlines the password selection procedure:
Type the Password
Press <Enter> without
ROM PCI/ISA BIO
and Press: <Enter>
entering the password
CMOS SETUP UTIL
AWARD SOFTWARE,
PASSWORD
Enter Password:
BIOS FEATURS SE
C
Enter Password:
Password Disabled!!
∗∗∗∗∗
P
SAVE & EXIT SETUP
Confirm Password:
∗∗∗∗∗
EXIT WITHOUT SAVING
After you confirm the password,
Esc : Quit
m
press <Esc> to exit
F10 : Save & Ex
olor
Time, Date, Hard Disk Type…
3-11 USER PASSWORD
When the user password option is on, you are not allowed to change any
setting in the [CMOS SETUP UTILITY] except for changing the user's
password.
The password setting procedure is similar to that for the [SUPERVISOR
PASSWORD] (Refer to section 3-9).
81
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup Utility
SY-K7VEMPRO
3-12 BOOT MENU
Boot Menu enables user to boot-up on different boot device without going into the BIOS
setup.
To enable boot Menu, press “ESC” after memory initialization, user will
see a device menu, in which user can choose on which device they wish to
boot from.
Boot Menu
== Select a Boot First device ==
Floppy
Ls120
HDD-0
SCSI
CDROM
HDD-1
HDD-2
HDD-3
ZIP100
LAN
:Move ENTER:Accept F4:Exit
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers Installation
SY-K7VEMPRO
Chapter 4
DRIVERS INSTALLATION
Your SY-K7VEMPRO Motherboard comes with a CD-ROM labeled
"SOYO CD." The SOYO CD contains the user's manual file for your new
Motherboard, the drivers software available for installation, and a database
in HTML format with information on SOYO Motherboards and other
products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be as
shown.
If you use Windows NT, 2000 or XP, the SOYO-CD will not detect your
motherboard type. In that case the following dialog will pop up, please
choose your motherboard and press OK. Now the SOYO-CD Start Up Menu
will be shown.
X
Please Select Your Board
LI-7000
7IWB
7IWA-F
7IWA-F V1.0
6IWM/L
6IWM
7IWB V1.0
7IWM
6IWA
7IWM/L V1
Cancel
OK
(SOYO CD Start Up Program Menu)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers Installation
SY-K7VEMPRO
If you use Windows 95/98/98SE/ME, the SOYO CD Start Up Program
automatically detects which SOYO Motherboard you own and displays the
corresponding model name.
The user's manual files included on the SOYO CD are in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat
Reader software must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader
utility is already present in your system, and otherwise prompts you on
whether or not you want to install it. You must install the Acrobat Reader
utility to be able to read the user's manual file. Follow the instructions on
your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers Installation
SY-K7VEMPRO
Step 2. Install Drivers
Click the Install Drivers button to display the list of drivers software that
can be installed with your Motherboard. The Start Up program displays
the drivers available for the particular model of Motherboard you own. We
recommend that you only install those drivers.
driver
revision:
VIA 4 in 1 Driver Package for Win 9x/ME/NT/2k/XP
VIA 8361 Onboard Display Driver for Win 98
VIA 8361 Onboard Display Driver for Win ME
VIA 8361 Onboard Display Driver for Win 2000
VIA 8361 Onboard Display Driver for Win NT4.0
VIA 8361 Onboard Display Driver for Win XP
VIA Onboard Audio Driver for Win 9x/ME/NT/2000/XP
VIA hardware monitor(R) for Win 9x/ME/NT/2000/XP
Cancel
OK
(Driver Installation Menu)
A short description of all available drivers follows:
ꢀ VIA 4in1 Driver Package for Win 9x/ME/NT/2k/XP
VIA 4 In 1 driver includes four system drivers to improve the performance
and maintain the stability of systems using VIA chipsets. These four
drivers are:
VIA Registry (INF) Driver, VIAAGP VxD driver, VIAATAPI Vendor
Support Driver and VIA PCI IRQ Miniport Driver. For Windows NT users,
the VIA IDE Bus Mastering driver is the only driver to be installed in your
system.
A description of 4 drivers follows:
Bus Master PCI IDE Driver
The ATAPI IDE driver enables the performance enhancing bus
mastering functions on ATA-capable Hard Disk Drives and ensures
IDE device compatibility.
VxD Driver
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers Installation
SY-K7VEMPRO
VIAAGP VxD Driver is to be installed if you are using an AGP
VGA device. VIAGART.VXD will provide service routines to your
VGA driver and interface directly to hardware, providing fast
graphical access.
VIA Chipset Functions Registry
VIA Registry (INF) Driver is to be installed under Windows. The
driver will enable the VIA Power Management function.
IRQ remapping utility (This driver is installed automatically)
VIA PCI IRQ Miniport Driver is to be installed under Windows 98
only, it sets the system's PCI IRQ routing sequence.
ꢀ VIA 8361 Onboard Display Driver for Win 98
In order to be able to make use of the integrated VGA function in your
VIA S3 chipset, you will need to install this driver first. For Win 98 only.
ꢀ VIA 8361 Onboard Display Driver for Win ME
In order to be able to make use of the integrated VGA function in your
VIA S3 chipset, you will need to install this driver first. For Win ME only.
ꢀ VIA 8361 Onboard Display Driver for Win 2000
In order to be able to make use of the integrated VGA function in your
VIA S3 chipset, you will need to install this driver first. For Win 2000
only.
ꢀ VIA 8361 Onboard Display Driver for Win NT4.0
In order to be able to make use of the integrated VGA function in your
VIA S3 chipset, you will need to install this driver first. For Win NT4.0
only.
ꢀ VIA 8361 Onboard Display Driver for Win XP
In order to be able to make use of the integrated VGA function in your
VIA S3 chipset, you will need to install this driver first. For Win XP only.
ꢀ VIA Onboard Audio Driver for Win 9x/ME/NT/2000/XP
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Drivers Installation
SY-K7VEMPRO
You have to install the drivers before installing any application for the
Onboard Audio. Please refer to the back of the manual for installation
information for other operating
ꢀ VIA hardware monitor(R) for Win 9x/ME/NT/2000/XP
Your motherboard comes with a hardware monitoring IC. By installing
this utility Temperature, Fan speed and Voltages can be monitored. It is
also possible to set alarms when current system values exceed or fall
below pre-set values.
Step 3. Select which driver you want to install and click OK
Notice 1: Once you have selected a driver, the system will automatically exit
the SOYO CD to begin the driver installation program. When the
installation is complete, most drivers require to restart your system
before they can become active.
Notice 2: You may click Cancel to abort the driver installation and return to
the main menu.
Step 4. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to
automatically find the latest BIOS, manual and driver releases for your
motherboard. This button will only work if your computer is connected to
the internet through a network or modem connection. Make sure to get
your modem connection up before clicking this button.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Realtek LAN Driver Installation
SY-K7VEMPRO
Chapter 5
REALTEK LAN DRIVER INSTALLATION
Install the Realtek LAN Drivers under windows 98
1. Move the mouse cursor to my computer icon, then press mouse right button
press properties.
2. Open Device Manager.
3. Under Network Adapters there will be a yellow marker the first time the
operating system is installed.
4. Select the “Driver” tab.
5. Click on update Driver.
6. The LAN Driver path is in SOYO CD:\driv-all\Realtek8139/Win98.
7. You will need windows 98 to complete the installation.
8. After informing windows of the directory the driver will be installed. Restart
your system after installation.
Install the Realtek LAN Drivers under windows NT4.0
1. Double click the Network icon in the control panel. The Network properties
windows will appear. Click on the Devices tab and press the Add button.
2. Select “Unlisted or Updated Drivers” from the list of drivers in the Add
window by placing the mouse pointer over it and clicking the left mouse
button. Press the OK button.
3. The install Driver dialog box will appear and request the path of the location
of the drivers to be installed. Enter D:\driv-all\Realtek8139\WinNT4(where
D:\is your CDROM drive)
4. After installation windows NT will display a dialog box asking you to restart
your system.
Install the Realtek LAN Drivers under windows ME
(Because windows ME can detect LAN driver automatic, so this
installation is for update driver)
1. Move the mouse cursor to my computer icon, then press mouse right button
press properties.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Realtek LAN Driver Installation
SY-K7VEMPRO
2. Open Device Manager.
3. Under
4. Select the “Driver” tab.
5. Click on update Driver.
6. The LAN driver path is in SOYO CD:\driv-all\Realtek8139\WinME.
Install the Realtek LAN Drivers under windows XP
(Because windows XP can detect LAN driver automatic, so this
installation is for update driver)
1. Move the mouse cursor to my computer icon, then press mouse right button
press properties.
2. Click hardware, then click Device manager.
3. Under Network Adapters there will be a LAN driver which XP detect is
installed, click it.
4. Select Driver, then click update driver.
5. Select install from a list or specific location, then click next.
6. The LAN driver path is in SOYO CD:\driv-all\Realtek8139\WinXP.
7. After install action. Restart your system.
Install the Realtek LAN Drivers under windows 2000
(Because windows 2000 can detect LAN driver automatic, so this
installation is for update Driver)
1. Press mouse right button then press properties.
2. Select hardware, then click Device manager.
3. Under Network Adapters there will be a LAN driver which 2000 detect is
installed, Double click it.
4. Select driver then click update driver.
5. Click next then select search for a suitable driver for my device.
6. Click next.
7. The LAN driver path is in SOYO CD:\driv-all\Realtek8139\Win2000.
8. Restart.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
|