SY-6IZM/3
Motherboard
Quick Start Guide
Tested To Comply
With FCC Standards
C
FC
FOR HOME OR OFFICE USE
POST CONSUMER
RECYCLED PAPER
100%
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
1
Introduction
Congratulations on your purchase of the SY-6IZM/3 Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-6IZM/3 Motherboard User's Guide and
Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
* If your board comes with a driver disc and a paper manual, the Quick Start Guide and the CD-ROM are not included in the package.
When unpacking the Motherboard, check for the following items:
u
u
u
u
u
u
u
The SY-6IZM/3 82440 ZX AGP/PCI Motherboard
This Quick Start Guide
The Installation CD-ROM
The CPU Retention Set
One IDE Device Flat Cable
One Floppy Disk Drive Flat Cable
Serial port flat cable with a 9-pin connector bracket
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
SY-6IZM/3 Motherboard Layout
PS/2 KB
Connector
PS/2 Mouse
Connector
CPUFAN
JP1
3
1
1
FDC
USB 1
COM 1
USB 2
Slot 1
PRT
Intel
82443 ZX
ATX
Power
COM2
JP3
3
1
1
IDE 2 IDE 1
VGA
JP44
WOL
Header
3
ATI
Game Port
RAGE Pro
Winbond
1
LINE-OUT
W83977EF
-AW
1
1
LINE-IN
MIC JACK
3V
JP7
5
1
Lithium
Battery
IR1
JP5
3
CMOS Clear
J4
Jumper
1
J5 1
PCI Slot #1
AC97
Codec
4
CHAFAN
1
Intel
_
_
HDD LED
82371EB
+
YAMAHA
YMF740-V
PCI Slot #2
PCI Slot #3
Speaker
_
Turbo
LED
+
+
PWRBT
Reset
Keylock
_
+
JP10
Power
LED
Winbond
W83782M
JP8
ISA Slot #1
C A 8 2 8
Hardware
Monitoring
Flash BIOS
W83781D
Key Features
Ø
Ø
Supports Intel Pentium® III processor (450-
550MHz), Pentium® II processor (233-
450MHz) & CeleronTM processor (266-
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Power-on by modem or alarm
Supports Wake-On-LAN (WOL)
Supports Power-On by PS/2 Keyboard
433MHz)
)
3 x 32-bit bus mastering PCI slots
Easy CPU settings in BIOS with the
“SOYO COMBO Setup”.
3D YAMAHA YMF740 Audio
ATI Rage Pro Graphics/Video with
8MB Video memory on board
Auto-detect CPU voltage
1 x 16-bit ISA slot
2 x USB ports
1 x IrDA port
Supports multiple-boot function
ATX power connector
Power failure resume
Ø
Ø
Ø
Ø
Ø
Ø
PC98, APM, ACPI, Ultra DMA/33
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
2
Installation
To avoid damage to your Motherboard, follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted portion
of the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
Check the Motherboard for damage. If any chip appears loose, press carefully to seat
it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new SY-6IZM/3 Motherboard. For detailed information, please refer to
SY-6IZM/3 Motherboard User's Guide and Technical Reference online manual included on
the CD-ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
u
u
u
u
u
u
u
u
u
Slot 1 processor with built-in CPU cooling fan (boxed type)
SDRAM module
Computer case and chassis with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device (PS/2 Mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive …
External Peripherals: Printer, Plotter, and Modem (optional)
Internal Peripherals: Modem and LAN cards (optional)
Notice 1: This Motherboard features one built-in VGA port and three built-in audio-stereo
ports. Therefore you do not need to install neither a VGA card nor a sound card.
Notice 2: If you want to use an external speaker connected to "Line-out" port, please make
sure to use an "amplified speaker" that can generate proper output sound volume.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Install the Motherboard
Follow the steps below in order to perform the installation of your new SY-6IZM/3 Motherboard.
Step 1. Install the CPU
Mark your CPU Frequency: Record the working frequency of your CPU
that should be clearly marked on the CPU cover.
FSB 66MHz
266MHz (66 x 4.0)
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
FSB 100MHz
350MHz (100 x 3. 5)
400MHz (100 x 4.0)
450MHz (100 x 4.5)
500MHz (100 x 5.0)
550MHz (100 x 5.5)
600MHz (100 x 6.0)
CPU Mount Procedure: To mount the processor that you have purchased
separately, follow these instructions.
Retention Module
Step 1. Open the two sides by folding them up.
Step 2. Push the locks on top of the CPU Step 3. Insert the CPU into the retention
inward.
module. The CPU fits in the CPU slot in
only ONE way, do not try to force it in.
Step 4. After completely inserting the CPU, push the two locks on
top of the CPU outward. Now your CPU is ready for use.
To remove the CPU, press
the two notches on top of
the CPU inward. Now
press the two slides on the
retention module down and
remove the CPU.
Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation.
Failing to install these items may result in overheating and possible burn-out of your CPU.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Step 2. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan,
Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-6IZM/3
Motherboard, please refer to SY-6IZM/3 Motherboard User's Guide and Technical
Reference online manual on CD-ROM.
Connectors and Plug-ins
Wake-On-LAN Header: JP44
IrDA (Infrared Device Header): IR1
Pin1
VCC
Pin2
Pin3
Pin4
Pin5
Pin1
Pin2
Pin3
None
IRRX
GND
IRTX
5VSB
GND MP-Wakeup
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin1
GND
Pin2
12V
Pin3
SENSOR
Pin1
GND
Pin2
12V
Pin3
SENSOR
Keylock
Key Lock
Speaker
Power LED
Power LED
Pin1 Pin2 Pin3
Pin1
Control Pin
Pin2
GND
1
1
1
5V
NC GND
Speaker
1
1
1
1
Pin1
5V
Pin2
NC
Pin3
NC
Pin4
Reset PWRBT Turbo LED HDD LED
Speaker out
HDD LED
Turbo LED
PWRBT
RESET
Pin1 Pin2
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
LED
Cathode
LED
Cathode
Power
On/Off
LED Anode
GND
GND
Power Good GND
CD Line-in: J4, J5
Pin 1 Pin 2 Pin 3 Pin 4
J4
J5
R
R
G
G
L
G
L
Connect the CD Line-in cord from the CD-ROM
device to the matching header J4 or J5.
G
ATX Power On/Off: PWRBT
ATX Power Supply: ATX PW
Connect your power switch to this Attach the ATX Power cable to this connector.
header (momentary switch type).
When using the Power-On by PS/2 Keyboard
function, please make sure the ATX power
supply can take at least 720mA load on the 5V
Standby lead (5VSB) to meet the standard ATX
specifications.
To turn off the system,
please press this switch and
hold down for longer than
4 seconds.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Step 3. Configure Memory
This Motherboard features 3 x DIMM for 168-pin 3.3V unbuffered DIMM
modules, providing support for up to 256MB of main memory using DIMM
modules from 8MB to 128MB.
Number of Memory
DIMM 1
DIMM 2
DIMM 3
Modules
Double-sided
/Single-sided
1
Double-sided
Double-sided
/Single-sided
2
3
Double-sided
Single-sided
Double-sided
/Single-sided
Single-sided
SDRAM
RAM Type
Memory Module
Size (MB)
8/16/32/64/128 Mbytes
Note: Because DIMM 2 and 3 are shared, double-sided DIMMs can be used
in only one of the DIMMs. With single-sided DIMMs both 2 and 3 can be used.
Step 4. Set JP3 for power up FSB clock and AGP bus clock.
JP3 is used to adjust AGP bus clock frequency depending on the value of the front side bus
(FSB) clock, also the setting of the JP3 determines the power up FSB clock which will
remain effective until the BIOS set the FSB clock to the CMOS setting.
3
2
1
3
2
1
JP3 Setting
Power up FSB Clock
AGP Clock
66MHz
100MHz
AGP Clock = FSB Clock ¸ 1
AGP Clock = FSB Clock ¸ 1.5
Note: The specification of maximum AGP bus Clock frequency is 66.6MHz.
*
*
*
Set JP3 to pin 1-2 short when you use a FSB 100MHz CPU.
Set JP3 to pin 2-3 short when you use a FSB 66MHz CPU.
Set JP3 to pin 1-2 short when you use a FSB 66MHz CPU but want to over clock the
FSB clock to 100MHz via the BIOS setting.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Step 5. Set the CPU Frequency
You do not need to set any jumper for the CPU frequency. Instead, CPU settings are
changed through the BIOS [SOYO COMBO SETUP]. Please refer to Chapter 3 - Quick
BIOS Setup for details on how to set the Slot 1 processor frequency.
Step 6. Enable/Disable Power-On by PS/2 Keyboard (JP1)
You can choose to enable the Power-On by PS/2 Keyboard function by shorting pin 2-3 on
jumper JP1, otherwise, short pin 1-2 to disable this function.
Support Power-On
Disable
Enable
by Keyboard
Disable Power-On
by PS/2 Keyboard
function
Enable Power-On
by PS/2 Keyboard
function
3
2
1
3
2
1
JP1 Setting
(short pin 1-2)
(short pin 2-3)
Important: When using the Power-On by PS/2 Keyboard function, please make sure
the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to
meet the standard ATX specifications.
Step 7. Power Button Enable (JP8)
Your system can be power on by either pressing a power button or typing in a password,
which can be set in the BIOS SOYO COMBO Setup. To avoid being unable to power up the
system due to of forgetting the password, you can place a jumper cap to short JP8. This will
always enable the Power Button.
Power Button
Enable
Power Button always Power Button according to
enabled
BIOS setting
Short pin to always
enable the Power
Button.
Open pin for a Power
Button function
according to the BIOS
setting.
JP8 Setting
Step 8. External Suspend Button (JP10)
Some cases come with a suspend button, insert the plug into JP10. In addition to through
this button, the system can also enter the suspend mode through your OS.
Note: Suspend mode only functions if your Power Management mode is APM. Make sure that the BIOS
setting for Power Management is APM. Windows 98 can be installed with ACPI Power Management
(default is APM), in this case suspend mode will not function either.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Step 9. Enable/Disable Onboard VGA(JP7)
The onboard VGA features of your Motherboard are controlled by jumper JP7.You can
choose to enable or disable the available VGA function by setting JP7 accordingly.
l
l
Leave JP7 open to enable the onboard VGA function. Then, you can plug your VGA
device monitor, after the Motherboard is installed. (You do not need to install any VGA
card.)
To disable the onboard VGA options short pin JP7.
Onboard VGA
Disable
Enable
Short pin to disable
the onboard VGA
function.
Open pin to enable
the onboard VGA
function.
JP7 Setting
Step 10. Back Panel Connector
JOYSTICK
PRT
PS/2 Mouse
Connector
USB2
PS/2 KB
Connector
LINE-IN
USB1
COM1
VGA
MIC JACK
LINE-OUT
Step 11. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5
seconds, and then by shorting pin 1-2 to retain new settings. This jumper can be easily
identified by its white colored cap.
CMOS Clearing
Retain CMOS Data
Clear CMOS Data
3
2
1
3
2
1
Short pin 2-3 for
at least 5 seconds
to clear the CMOS.
Short pin 1-2 to retain
the new settings.
JP5 Setting
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Note on Over-clocking Capability
The 6IZM/3 Motherboard provides over-clocking capability. Due to the over-clocking setting
your system may fail to boot up or hang during run time. If this occurs, please perform the
following steps to recover your system from the abnormal situation:
1. Turn off system power (If you use a ATX power supply, sometimes you have to press
the power button for more then 4 seconds to shut down the system)
2. Set the JP3 to pin 2-3 short if you use a FSB 66MHz CPU
3. Press and hold down the <Insert> key while turning on the system power. Keep
holding down the <Insert> key until you see the message of the CPU type and
frequency (133MHz or 200MHz) appear on screen
4. Press the <Del> key during the system diagnostic checks to enter the Award BIOS
Setup program
5. From the BIOS main menu, select [SOYO COMBO] and move the cursor to the [CPU
Frequency] field to set the proper working frequency
6. Select [Save & Exit SETUP] and press <Enter> to save the configuration to the
CMOS memory, and continue the boot sequence
Note: SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
3
Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The
[SOYO COMBO SETUP] menu combines the main CPU parameters that you need to
configure, all in one menu, for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then press the <DEL> key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 3. Select [SOYO COMBO SETUP]
Move the cursor to the [CPU Speed] field to set the CPU working speed.
Available [CPU Speed] settings on your SY-6IZM/3 Motherboard are detailed in the following
table. If you set this field to [Manual], you are then required to fill in the next two consecutive
fields: (1) the CPU Ratio, and (2) the CPU Frequency.
Select the working frequency of
your Pentium® III, Pentium® II,
CeleronÔ processor among these
preset values.
CPU Frequency
233MHz (66 x 3.5)
350MHz (100 x 3.5)
400MHz (100 x 4.0)
450MHz (100 x 4.5)
500MHz (100 x 5.0)
550MHz (100 x 5.5)
600MHz (100 x 6.0)
266MHz (66 x 4.0)
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
Note:
Mark the checkbox that
corresponds to the working
frequency of your Pentium® III,
Pentium® II, CeleronÔ processor in
case the CMOS configuration
should be lost.
Note: if you use Bus Frequencies of 75 MHz, make sure that your PCI cards can cope with
the higher PCI clock.
Step 4. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue the boot
sequence.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
4
The SOYO CD
Your SY-6IZM/3 Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains the user's manual file for your new Motherboard, the drivers software available for
installation, and a database in HTML format with information on SOYO Motherboards and
other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below.
(SOYO CD Start Up Program Menu)
The SOYO CD Start Up Program automatically detects which SOYO Motherboard you own
and displays the corresponding model name.
Step 2. Read SOYO [6IZM/3] Manual
Click the Read Manual button to open the user's manual file of your Motherboard.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Please note that if the Start Up program was unable to determine which SOYO Motherboard
you own, the manual selection menu will pop up, as shown below. Then select the user's
manual file that corresponds to your Motherboard model name and click OK.
SOYO CD Manuals
Please select your manual In the box below
and click OK.
6IZM/3
OK
Back
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the Install Drivers button to display the list of drivers software that can be installed with
your Motherboard. The Start Up program displays the drivers available for the particular
model of Motherboard you own. We recommend that you only install those drivers.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
The following drivers are available for Windows 95
(Driver Installation Menu)
The following drivers are available for Windows 98
(Driver Installation Menu)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
A short description of all available drivers follows:
Ø
Intel Southbridge Drivers
Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX,
BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for
Windows 95)
Ø
SOYO SpeedPro Busmaster Driver for Win 95/98
Without the busmaster drivers the CPU will need to be involved every time data is read from
or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access)
to relieve the CPU of this burden, thus speeding up the system.
The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it an
advantage over other busmaster drivers.
Ø
Ø
Ø
Intel Busmaster Drivers for Windows 95
Intel Busmaster Drivers for Win NT
Intel Busmaster Drivers for OS/2
These are the official busmaster drivers as supplied by Intel.
Note: Do NEVER install two types of busmaster drivers on your system, this will
lead to conflicts and system instability. Therefore, if you install the SOYO
SpeedPro Busmaster driver you can NOT install the Intel Busmaster drivers.
Before installing a new busmaster driver first UNINSTALL the old busmaster
driver.
Ø
SOYO CD Xpress Utility
This utility will enhance your CD-ROM Drive data-thoughput by using space on the Harddisk
as cache. This way application programs can access data faster. This utility is suitable for
Windows 95/98.
Ø
System Monitor Utility
Your motherbaord comes with a hardware monitoring IC. By installing this utility Temperature,
Fan speed and Voltages can be monitored. It is also possible to set alarms when current
system values exceed or fall below pre-set values.
This utility comes with a preset monitoring rage for the CPU voltage. However, the core
voltage of the processor you purchased may fall out of this preset range, so you may need to
adjust the pre-set value. Please refer to the SY-6IZM/3 Motherboard’s CD manual for the
details.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IZM/3 Quick Start Guide
Ø
YAMAHA 740 Sound Drivers for Win95/98 and Win NT
With this application program the user can make use of the on board sound chip. Before
installing the YAMHA 740 Sound Drivers, you MUST first install the YAMAHA 740 drivers for
Windows 9x or NT.
Ø
ATI Rage Pro AGP
Select this Item and click OK to start up the ATI Rage PRO AGP driver screen. Follow the
instructions on the screen to install the drivers and/or application programs you need.
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers require
to restart your system before they can become active.
However, to display the list of all drivers software available with SOYO Motherboards, click
the Display all drivers on the SOYO CD button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: February 1999
Version 1.0
International Headquarters
Soyo Computer Inc., (Taiwan)
Tel: 886-2-2290-3300
Fax: 886-2-2298-3322
E-mail: [email protected]
6IZM/3 SERIAL
USA Branch Office
Soyo Tek Inc., (USA)
Tel: (408) 452-7696
Fax: (408) 573-7696
E-mail: [email protected]
SOYO Europe
Soyo Europe B.V., (Holland)
Tel: 31-79-3637500
Fax: 31-79-3637575
E-mail: [email protected]
Germany Branch Office
SAAT Technology GmbH, (Germany)
Tel: 49-(0)441-204044
Fax: 49-(0)441-203422
Email: [email protected]
UK Branch Office
Soyo (U.K.) Ltd.
Tel: 44-(0)181-569 4111
Fax: 44-(0)181-569 4134
E-mail: [email protected]
Japan Branch Office
Soyo Computer (Japan)
Tel: 81-3-33682188
Fax: 81-3-33682199
E-mail: [email protected]
Hong Kong Branch Office
Soyo Hong Kong Ltd. (H.K.)
Tel: 852-2710-9810
Fax: 852-2710-9078
E-mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|