SY-6IEB
Motherboard
Quick Start Guide
Tested To Comply
With FCC Standards
C
FC
FOR HOME OR OFFICE USE
POST CONSUMER
RECYCLED PAPER
100%
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
1
Introduction
Congratulations on your purchase of the SY-6IEB Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-6IEB Motherboard User's Guide and
Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
* If your board comes with a driver disc and a paper manual, the Quick Start Guide and the CD-ROM are not included in the package.
When unpacking the Motherboard, check for the following items:
u
u
u
The SY-6IEB 82440 EX/LX AGP/PCI Motherboard
This Quick Start Guide
The Installation CD-ROM
u
u
The CPU Retention Set
One IDE Device Flat Cable
u
u
One Floppy Disk Drive Flat Cable
One 9-pin serial connector with 9-pin flat cable and 6-pin
PS/2 mouse connector with 6-pin cable
u
One 25-pin parallel connector with 25-pin flat cable and 9-
pin serial connector with 9-pin flat cable
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
SY-6IEB Motherboard Layout
COM 2 COM 1
KB
Connector
1
1
JP10
PS/2 Mouse
1
3
LPT
1
Connector
USB
ITE8671
I/O Chipset
FDC
1
ISA Slot #2
1
AT Power
ATX
Power
ISA Slot #1
JP44
IR
1
5
1
1
CPUFAN
3
Slot 1 for
Pentium R II Processor
AGP Slot
Intel
82443 EX
PCI Slot #2
PCI Slot #1
PCI Slot #3
Intel
82371 EB
DIMM 2
DIMM 1
HDD
LED
_
_
_
+
JP5
1
3
CMOS Clear
Jumper
SPEAKER
_Turbo
Flash BIOS
LED
+
+
PWRBT
1
Key
Lock
3V
Lithium
Battery
IDE 2
Reset CHAFAN
Power
LED
1
+
IDE 1
Flash BIOS
1
Key Features
Ø
Supports Intel Pentium® II
processors (233-333MHz) &
Ø
Supports Creative SB-LINK ™ (PC-PCI)
for PCI audio card
1 x 32-bit AGP slot
Celeron ™ processors (266-433MHz)
Auto-detect CPU voltage
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
3 x 32-bit bus mastering PCI slots
2 x USB ports
1 x IrDA port
PC98, APM, ACPI, Ultra DMA/33
Power-on by modem or alarm
SOYO COMBO Setup
Supports multiple-boot function
Y2K Complaint
AT & ATX power connectors
Supports Wake-On-LAN (WOL)
Power-on by Keyboard
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
2
Installation
To avoid damage to your Motherboard, follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted portion
of the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
Check the Motherboard for damage. If any chip appears loose, press carefully to seat
it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new SY-6IEB Motherboard. For detailed information, please refer to SY-
6IEB Motherboard User's Guide and Technical Reference online manual included on the
CD-ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
u
u
u
u
u
u
u
u
u
u
Slot 1 processor with built-in CPU cooling fan (boxed type)
SDRAM module
Computer case and chassis with adequate power supply unit
Monitor
PS/2 Keyboard
Pointing Device (PS/2 Mouse)
VGA Card
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive …
External Peripherals: Printer, Plotter, and Modem (optional)
Internal Peripherals: Modem and LAN cards (optional)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Install the Motherboard
Follow the steps below in order to perform the installation of your new SY-6IEB
Motherboard.
Step 1. Install the CPU
Mark your CPU Frequency: Record the working frequency of your CPU
that should be clearly marked on the CPU cover.
FSB 66MHz
266MHz (66 x 4.0)
300MHz (66 x 4.5)
333MHz (66 x 5.0)
366MHz (66 x 5.5)
400MHz (66 x 6.0)
433MHz (66 x 6.5)
CPU Mount Procedure: To mount the processor that you have purchased
separately, follow these instructions.
Retention Module
Step 1. Open the two sides by folding them up.
Step 2. Push the locks on top of the CPU Step 3. Insert the CPU into the retention
inward.
module. The CPU fits in the CPU slot in
only ONE way, do not try to force it in.
Step 4. After completely inserting the CPU, push the two locks on
top of the CPU outward. Now your CPU is ready for use.
To remove the CPU, press
the two notches on top of
the CPU inward. Now
press the two slides on the
retention module down and
remove the CPU.
Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation.
Failing to install these items may result in overheating and possible burn-out of your CPU.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Step 2. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan,
Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-6IEB
Motherboard, please refer to SY-6IEB Motherboard User's Guide and Technical Reference
online manual on CD-ROM.
Connectors and Plug-ins
PCI Audio Card Header: SB-Link ™(PC-PCI)
Wake-On-LAN Header: JP44
Connect the SB-Link ™(PC-PCI) cable from your
PCI audio card to this header.
Pin1
Pin2
Pin3
5VSB
GND
MP-Wakeup
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin1
GND
Pin2
12V
Pin3
SENSOR
Pin1
GND
Pin2
12V
Pin3
SENSOR
Key Lock
Speaker
Power LED
Power LED
Pin1 Pin2 Pin3
Keylock
Pin1
Control Pin
Pin2
GND
1
1
1
5V
NC GND
Speaker
1
1
1
1
Pin1
5V
Pin2
NC
Pin3
NC
Pin4
Reset PWRBT Turbo LED HDD LED
Speaker out
HDD LED
Turbo LED
PWRBT
RESET
Pin1 Pin2
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
LED
Cathode
LED
Cathode
Power
On/Off
LED Anode
GND
GND
Power Good GND
IrDA (Infrared Device Header): IR1
AT Power Cable
Pin1
VCC
Pin2
None
Pin3
IRRX
Pin4
GND
Pin5
IRTX
Connect the AT Power cable to this
connector. If you use AT power supply.
ATX Power On/Off: PWRBT
ATX Power Supply: ATX PW
Connect your power switch to this Attach the ATX Power cable to this connector. If
header (momentary switch type). you use ATX power supply.
To turn off the system,
please press this switch and
hold down for longer than
4 seconds.
When using the Keyboard Wake-Up
function, please make sure the ATX
power supply can take at least 720mA
load on the 5V Standby lead (5VSB) to
meet the standard ATX specifications.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Step 3. Configure Memory
Your board comes with two DIMM sockets, providing support for up to 256MB of main
memory using DIMM modules from 8MB to 128MB with no restriction on memory
configuration. Therefore, you can install memory modules in any combination.
Memory Configuration
DIMM Banks
MEMORY
CONFIGURATION
DIMM 1
DIMM 2
RAM Type
EDO/SDRAM
8/16/32/64/128
EDO/SDRAM
8/16/32/64/128
RAM Module Size (MB)
Note : There are two types of DIMM modules with different operating voltages:
3.3V and 5.0V. Please note that only 3.3V EDO DIMM modules can be used
on this Motherboard.
Step 4. Set the CPU Frequency
You do not need to set any jumper for the CPU frequency. Instead, CPU settings are
changed through the BIOS [SOYO COMBO SETUP]. Please refer to Chapter 3 - Quick
BIOS Setup for details on how to set the Pentium® II processor frequency.
Step 5. Enable/Disable the Keyboard Wake-Up (JP10)
You can choose to enable the Wake-Up by Keyboard or Mouse function by shorting pin 1-2
on jumper JP1, otherwise, short pin 2-3 to disable this function.
Support Wake-Up
by Keyboard
Enable
Disable
Enable Wake-up
by Keyboard
function
Disable Wake-up
by Keyboard
function
JP10 Setting
2
3
1
2
3
1
(short pin 1-2)
(short pin 2-3)
Important: When using the Keyboard Wake-Up function, please make sure the ATX
power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the
standard ATX specifications.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Step 6. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5
seconds, and then by shorting pin 1-2 to retain new settings. This jumper can be easily
identified by its white colored cap.
CMOS Clearing
Retain CMOS Data
Clear CMOS Data
Short pin 2-3 for
at least 5 seconds
to clear the CMOS.
Short pin 1-2 to retain
the new settings.
JP5 Setting
2
3
1
2
3
1
Note: You must unplug the AT/ATX power cable from the AT/ATX power connector
when performing the CMOS Clear operation.
Note on Over-clocking Capability
The SY-6IEB provides over-clocking capability. Due to the over-clocking setting your system
may fail to boot up or hang during run time. Please perform the following steps to recover
your system from the abnormal situation :
1.Turn off system power.
2.Press and hold down the <Insert> key while turning on the system power. Keep holding
down the <Insert> key until you see the message of the CPU type and frequency shown
on the screen.
3.Press the <Del> key during the system diagnostic checks to enter the Award BIOS Setup
program.
4.Select [SOYO COMBO SETUP] and move the cursor to the [CPU Frequency] field to set
the proper working frequency.
5.Select [Save & Exit SETUP] and press <Enter> to save the new configuration to the
CMOS memory, and continue the boot sequence.
Note: SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
3
Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The
[SOYO COMBO SETUP] menu combines the main CPU parameters that you need to
configure, all in one menu, for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then press the <DEL> key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 3. Select [SOYO COMBO SETUP]
Move the cursor to the [CPU Speed] field to set the CPU working speed.
Available [CPU Speed] settings on your SY-6IEB Motherboard are detailed in the following
table. If you set this field to [Manual], you are then required to fill in the next two consecutive
fields: (1) the CPU Ratio, and (2) the CPU Frequency.
Select the working frequency of your
Pentium® II, or CeleronÔ processor
among these preset values.
CPU Speed
233MHz (66x3.5)
366MHz (66x5.5)
400MHz (66x6.0)
433MHz (66x6.5)
Note:
Mark the checkbox that
266MHz (66x4.0)
300MHz (66x4.5)
333MHz (66x5.0)
corresponds to the working frequency of
your Pentium® II, or CeleronÔ processor
in case the CMOS configuration should
be lost.
Step 4. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue the boot
sequence.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
4
The SOYO CD
Your SY-6IEB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains the user's manual file for your new Motherboard, the drivers software available for
installation, and a database in HTML format with information on SOYO Motherboards and
other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below.
(SOYO CD Start Up Program Menu)
The SOYO CD Start Up Program automatically detects which SOYO Motherboard you own
and displays the corresponding model name.
Step 2. Read SOYO [6IEB] Manual
Click the Read Manual button to open the user's manual file of your Motherboard.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Please note that if the Start Up program was unable to determine which SOYO Motherboard
you own, the manual selection menu will pop up, as shown below. Then select the user's
manual file that corresponds to your Motherboard model name and click OK.
6IEB
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the Install Drivers button to display the list of drivers software that can be installed with
your Motherboard. The Start Up program displays the drivers available for the particular
model of Motherboard you own. We recommend that you only install those drivers.
However, to display the list of all drivers software available with SOYO Motherboards, click
the Display all drivers on the SOYO CD button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
The following drivers are available for Windows 95
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel Southbridge Drivers
SOYO Speedpro BusMaster Driver for win 95/98
Intel Bus Master Drivers for Win95
Intel Bus Master Drivers for Win NT
Intel Bus Master Drivers for OS/2
SOYO CD Xpress utility
Display all drivers
on the SOYO CD
Cancel
OK
(Driver Installation Menu)
The following drivers are available for Windows 98
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
SOYO Speedpro BusMaster Driver for win 95/98
Intel Bus Master Drivers for Win NT
Intel Bus Master Drivers for OS/2
SOYO CD Xpress utility
Display all drivers
on the SOYO CD
Cancel
OK
(Driver Installation Menu)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
A short description of all available drivers follows:
Ø
Intel Southbridge Drivers
Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX,
BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for
Windows 95)
Ø
SOYO SpeedPro Busmaster Driver for Win 95/98
Without the busmaster drivers the CPU will need to be involved every time data is read from
or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access)
to relieve the CPU of this burden, thus speeding up the system.
The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it an
advantage over other busmaster drivers.
Ø
Ø
Ø
Intel Busmaster Drivers for Windows 95
Intel Busmaster Drivers for Win NT
Intel Busmaster Drivers for OS/2
These are the official busmaster drivers as supplied by Intel.
Note: Do NEVER install two types of busmaster drivers on your system, this will
lead to conflicts and system instability. Therefore, if you install the SOYO
SpeedPro Busmaster driver you can NOT install the Intel Busmaster drivers.
Before installing a new busmaster driver first UNINSTALL the old busmaster
driver.
Ø
SOYO CD Xpress Utility
This utility will enhance your CD-ROM Drive data-thoughput by using space on the Harddisk
as cache. This way application programs can access data faster. This utility is suitable for
Windows 95/98.
Select which driver you want to install and click OK, or click Cancel to abort the driver
installation and return to the main menu.
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers require
to restart your system before they can become active.
However, to display the list of all drivers software available with SOYO Motherboards, click
the Display all drivers on the SOYO CD button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-6IEB Quick Start Guide
Step 4. Enter the SOYO CD
Click the Enter SOYO CD button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available in as many as eleven different languages. For your convenience, this
information is available in HTML format, similar to the format widely used on the Internet.
(SOYO CD HTML Database in English*)
(* The list of menu options may vary between languages)
Note: If no HTML browser is installed on your system, the Start Up program will prompt you
on whether or not you would like to install the Internet Explorer* browser. Click YES to install
the HTML browser. After the installation is complete, please restart your system. Then re-run
the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: March 1999
Version 2.0
SY-6IEB
International Headquarters
Soyo Computer Inc., (Taiwan)
Tel: 886-2-2290-3300
Korea Branch Office
SOYO TECHNOLOGY CO., LTD.
Tel: 82-2-3272-6481
SERIAL
Fax: 886-2-2298-3322
E-mail: [email protected]
Fax: 82-2-704-2619
Email:[email protected]
Email:[email protected]
USA Branch Office
Soyo Tek Inc., (USA)
Tel: (408) 452-7696
U.K. Branch Office
SOYO (U.K.) LTD.
Tel: 44-(0)181-569 4111
Fax: 44-(0)181-569 4134
Email:[email protected]
Fax: (408) 573-7696
E-mail: [email protected]
SOYO Europe
Soyo Europe B.V., (Holland)
Tel: 31-79-3637500
Japan Branch Office
SOYO COMPUTER ® è¦ ¡· |ª
À
Fax: 31-79-3637575
Tel: 81-3-33682188
Fax: 81-3-33682199
E-mail: [email protected]
E-mail: [email protected]
Germany Branch Office
SOYO Deutschland GmbH
Tel: 49-(0)441-209100
Hong Kong Branch Office
Soyo Hong Kong Ltd. (H.K.)
Tel: 852-2710-9810
Fax: 49-(0)441-203422
Email:[email protected]
Fax: 852-2710-9078
E-mail: [email protected]
China
GING MEI JEI LTD.
Tel: 86-10-6251-0089/91/92
Fax: 86-10-6251-0311
Email:[email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|