SY-5SSM
Motherboard
Quick Start Guide
Tested To Comply
C
With FCC Standards
FOR HOME OR OFFICE USE
FC
POST CONSUMER
RECYCLED PAPER
100%
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
1
Introduction
Congratulations on your purchase of the SY-5SSM Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-5SSM Motherboard User's Guide
and Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
* If your board comes with a driver disc and a paper manual, the Quick Start Guide and the CD-ROM are not included in the
package.
When unpacking the Motherboard, check for the following
items:
u
u
u
u
u
u
The SY-5SSM Motherboard
This Quick Start Guide
The Installation CD-ROM
One IDE Device Flat Cable
One Floppy Disk Drive Flat Cable
One serial port flat cable with a 9-pin connector
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
SY-5SSM Motherboard Layout
PS/2 KB PS/2 Mouse
Connector
Connector
2
4
3
6
8
10
9
J1
JP30
1
2
5
7
6 SW1
4
P.B. SRAM
64Kx64
USB 1
USB 2
PRT
ATX
Power
1
3
5
IDE 2IDE 1
COM 1
COM 2
P.B. SRAM
64Kx64
1
CHAFAN
1
CPUFAN
8
6
4
2
7
5
3
1
VGA
1
1
SiS 530
Chipset
FDD
JP32
+
JOYSTICK
Power
LED
LINE-OUT
_
KEY
LOCK
+
LINE-IN
+
DIMM 1
DIMM 2
_
+
Speaker
MIC JACK
_
_
DIMM 3
4
1
1
PCI Slot #1
CD IN1
CD IN2
3V
Lithium
Battery
JP5
4
PCI Slot #2
PCI Slot #3
PCI Slot #4
3
1
IR1
JP44
ES1938
SiS
5595
1
1
3
WOL
Header
®
I/O Chip
JP9
ITE 8661
ISA Slot #1
Flash BIOS
Key Features
Ø
Integrated 3D AGP accelerator supports
UMA or non-UMA (option)
3D PnP PCI Audio onboard
1 MB L2 cache on board
Supports CPU voltage from 2.0V to 3.5V
in 0.1V increment
PC98, ACPI, Ultra DMA 33/66
Power-on by modem or alarm
Supports Wake-On-LAN (WOL)
Ø
Ø
Supports power-off by hot-key
3 x 32-bit bus mastering PCI slots & 1 x
32-bit bus slaving PCI slot
2 x USB ports
1 x IrDA port
Supports multiple-boot function
Supports Pentium® class CPU with host
bus clock of 66/100 MHz
Supports system memory up to
768MBytes
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
2
Installation
To avoid damage to your Motherboard, follow these simple rules while handling
this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted
portion of the system's metal chassis.
l
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
Check the Motherboard for damage. If any chip appears loose, press carefully to
seat it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new SY-5SSM Motherboard. For detailed information, please refer to
SY-5SSM Motherboard User's guide and Technical Reference online manual included on
the CD-ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
u
u
u
u
u
u
u
u
u
Pentium® processor with cooling fan
DIMM memory module
Computer case and chassis with adequate power supply unit
Monitor
Keyboard
Pointing Device (PS/2 mouse)
Speaker(s) (optional)
Disk Drives: HDD, CD-ROM, Floppy drive …
External Peripherals: Printer, Plotter, and Modem- (optional)
Internal Peripherals: Modem and LAN cards (optional)
Notice 1: This Motherboard features one built-in VGA port and three built-in audio-stereo
ports. Therefore you do not need to install neither a VGA card nor a sound card.
Notice 2: When using the onboard VGA, please install DRAM modules in bank "DIMM 1"
in priority.
Notice 3: If you want to use an external speaker connected to "Line-out" port, make sure
to use an "amplified speaker" that can generate proper output sound volume.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Install the Motherboard
Follow the steps below in order to perform the installation of your new SY-5SSM
Motherboard.
Step 1. Install the CPU
To mount the Pentium® class processor that you have purchased separately, follow these
instructions.
CPU Mount Procedure
1
2
3
4
1. Lift the socket handle up to a vertical position.
2. Align the blunt edge of the CPU with the matching pinhole distinctive edge on the
socket.
3. Seat the processor in the socket completely and without forcing.
4. Then close the socket handle to secure the CPU in place.
Remember to connect the CPU Cooling Fan to the appropriate power
connector (CPUFAN) on the Motherboard. The fan is a key component that
will ensure system stability. The fan prevents overheating, therefore
prolonging the life of your CPU.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Step 2. Set the CPU Voltage ( JP30)
For CPUs that come with different voltages, please verify the correct voltage settings with
your dealer before installation. Use the following table to set JP30 to the proper "voltage
value", according to the specifications marked on your CPU:
Voltage Setting: JP30
Processor
Voltage
1-2
3-4
5-6
7-8
9-10
3.52 V
open
short
short
short
short
AMD K5 PR100
AMD K5 PR133
AMD K5 PR166
The AMD K5 and K6 come in several versions with different voltages.
Please verify the correct voltage settings with your dealer before
installation. The most common K5 runs on 3.52V.
AMD K6 166
AMD K6 200
2.9 V
3.2 V
open
open
short
short
short
short
open
open
short
AMD K6 233
open
AMD K6 266
AMD K6 300
AMD K6-2 266
AMD K6-2 300
AMD K6-2 333
AMD K6-2 350
AMD K6-2 366
AMD K6-2 380
AMD K6-2 400
2.2 V
2.3 V
open
open
open
short
open
AMD K6-2 450
open
open
open
short
short
The Cyrix 6X86(L) and M
voltages. Please ask your dealer for the correct voltage.
¢
º
come in several versions with different
Cyrix 6x86(L) PR166+
Cyrix 6x86(L) PR200+
Cyrix 6x86MX PR166
Cyrix 6x86MX PR200
Cyrix 6x86MX PR233
Cyrix 6x86MX PR266
2.9 V
3.3 V
open
open
short
short
open
open
open
short
short
Cyrix M
Cyrix M
Cyrix M
¢
¢
¢
º
º
º
300
333
350
Intel P54C P100
Intel P54C P133
Intel P54C P166
Intel P54C P200
short
The P54C (standard Pentium®) comes in several versions with different
voltages. Please ask your dealer for the correct voltage. The most
common P54C runs on 3.3V.
Intel P55C P166
Intel P55C P200
Intel P55C P233
2.8 V
open
short
open
open open
The P55C (MMX) processors have the same voltage setting.
IDT WinChip C6/W2-200
IDT WinChip C6/W2-225
3.52 V
open
short
short
short
short
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Step 3. Set JP32, SW1 for CPU Frequency
The DIP switch SW1 enable you to assign the Multiplier and Bus Clock, as shown in the
following table:
Frequency
Multiplier: SW1
1-2 3-4 5-6
CPU Host Bus Setting: JP32
Multi-
plier
Processor
AMD K5 PR100
AMD K5 PR133
AMD K5 PR166
AMD K6 166
AMD K6 200
AMD K6 233
AMD K6 266
Bus Clock
1-2
3-4
5-6
7-8
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
1.5 x open short short short open open open
2.0 x open short short short short open open
2.5 x open short short short short short open
2.5 x open short short short short short open
3.0 x open short short short open short open
3.5 x open short short short open open open
4.0 x open short short short short open short
4.5 x open short short short short short short
4.0 x open short short short short open short
4.5 x open short short short short short short
AMD K6 300
AMD K6-2 266
AMD K6-2 300
AMD K6-2 300
AMD K6-2 333
AMD K6-2 333
AMD K6-2 350
AMD K6-2 366
AMD K6-2 380
AMD K6-2 400
AMD K6-2 450
Cyrix 6x86 PR166+
Cyrix 6x86 PR200+
Cyrix 6x86MX PR166
Cyrix 6x86MX PR200
Cyrix 6x86MX PR200
Cyrix 6x86MX PR233
Cyrix 6x86MX PR266
100 MHz 3.0 x open open short short open short open
66MHz
95MHz
100MHz 3.5 x open open short short open open open
66MHz
95MHz
5.0 x open short short short open short short
3.5 x open short open open open open open
5.5 x open short short short open open short
4.0 x open short open open short open short
100MHz 4.0 x open open short short short open short
100MHz 4.5 x open open short short short short short
66 MHz
75 MHz
66 MHz
66 MHz
75 MHz
75 MHz
83 MHz
66 MHz
75 MHz
66 MHz
75 MHz
83MHz
100MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
66 MHz
75 MHz
2.0 x open short short short short open open
2.0 x open short short open short open open
2.0 x open short short short short open open
2.5 x open short short short short short open
2.0 x open short short open short open open
2.5 x open short short open short short open
2.5 x open short open short short short open
3.5 x open short short short open open open
3.0 x open short short open open short open
4.0 x open short short short short open short
3.5 x open short short open open open open
3.0 x open short open short open short open
2.5 x open open short short short short open
1.5 x open short short short open open open
2.0 x open short short short short open open
2.5 x open short short short short short open
3.0 x open short short short open short open
3.0 x open short short short open short open
3.5 x open short short short open open open
3.0 x open short short short open short open
3.0 x open short short open open short open
Cyrix M II-300
Cyrix M II-333
Intel P54C P100
Intel P54C P133
Intel P54C P166
Intel P54C P200
Intel P55C P200
Intel P55C P233
IDT WinChip C6/W2-200
IDT WinChip C6/W2-225
This main board supports various CPU multiplier and host bus frequency settings.
Please select the proper frequency setting based on specifications of the CPU you have purchased. System
stability or components damage, in case of over-specification setting, is not guaranteed.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Step 4. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Front Panel
Devices (ACPI LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch.),
Wake-On-LAN card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-5SSM
Motherboard, please refer to SY-5SSM Motherboard User's Guide and Technical Reference
online manual on CD-ROM.
Note: An ATA/66 cable (40-pin, 80-conductor cable) must be used to ensure proper
operation of the Ultra ATA/66 hard drive.
Connectors and Plug-ins
IrDA (Infrared Device Header): IR1
Wake-On-LAN Header: JP44
Pin1
VCC
Pin2
None
Pin3
IRRX
Pin4
GND
Pin5
IRTX
Pin1
5VSB
Pin2
GND
Pin3
MP-Wakeup
CPU Cooling Fan: CPUFAN
Chassis Fan: CHAFAN
Pin1
GND
Pin2
12V
Pin3
SENSOR
CD Line-in:CD IN1,CD IN2
Connect the CD Line-in cord from the CR-ROM
device to the matching connector CD IN1 or CD IN2.
Pin1
GND
Pin2
12V
Pin3
SENSOR
Pin1
L
Pin2
G
Pin3
Pin4
R
CD IN1
CD IN2
G
G
L
G
R
Key Lock
Speaker
Power LED
Power LED
Keylock
Pin1
Control Pin
Pin2
GND
Pin1 Pin2 Pin3
5V
1
1
1
1
NC GND
Speaker
1
1
1
Pin1
5V
Pin2
NC
Pin3
NC
Pin4
Speaker out
Reset
PWRBT ACPI LED HDD LED
HDD LED
ACPI LED
PWRBT
RESET
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
Pin1
Pin2
LED
Cathode
LED
Cathode
Power
On/Off
Power
Good
LEDAnode
LEDAnode
GND
GND
ATX Power On/Off: PWRBT
Connect your power switch to this header (momentary switch type).
To turn off the system, please press this switch and hold down for longer than 4 seconds.
ATX Power Supply: ATX PW
Attach the ATX Power cable to this connector. If you use ATX power supply.
When using the Power-On by PS/2 Keyboard function, please make sure the ATX power supply can
take at least 720mA load on the 5V Standby lead (5VSB) to meet the standard ATX specifications.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Step 5. Configure Memory
Your board comes with three DIMM sockets, providing support for up to 768MB of main
memory using DIMM modules from 8MB to 256MB. For 66/75MHz host bus CPUs use
12ns or faster DIMM modules.
Memory Configuration Table
MEMORY
CONFIGURATION
DIMM Banks
DIMM 2
DIMM 1
DIMM 3
RAM Type
SDRAM
SDRAM
SDRAM
Single RAM
Module Size (MB)
8/16/32/64/128/256 8/16/32/64/128/256 8/16/32/64/128/256
Note: If you plan on using the onboard VGA and intend to install only
one DRAM module, then this single DRAM must be installed in
bank DIMM 1.
Step 6. Select the CPU Burst Mode (J1)
There are two types of CPU burst modes according to manufacturer design:
Ø
Ø
Interleave Burst (CPU: Intel P54C/P55C, AMD K5/K6/K6-2, IDT
WinChip)
Linear Mode
(CPU: Cyrix 6x86/L/MX/M
¢
)º
Interleave
Linear
Intel® P54C/P55C
AMD ™ K5/K6/K6-2
IDT WinChip
CPU Burst Mode
J1 Setting
Cyrix ™ 6x86/L/MX/M
¢
º
When using Intel
or AMD CPUs.
When using
Cyrix type of
CPU.
1
2
1
2
If you are using a Cyrix ™ 6x86/L/MX/M II series CPU, set the burst mode to Linear by
shorting jumper J1, and follow the following steps to select the correct Linear burst mode
in BIOS:
1. During the boot-up initial sequence, press the [Delete] key to enter the BIOS setup
menu.
2. Select the [CHIPSET FEATURES SETUP] section in BIOS.
3. In the [CHIPSET FEATURES SETUP] sub-menu, set the [Linear Mode] field to
[Enabled].
4. Press [Esc] to return to the BIOS main menu.
5. Then choose [Save & Exit Setup] to re-boot your computer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Step 7. Enable/Disable the Onboard Sound (JP9)
The onboard audio features of your Motherboard are controlled by jumpers JP9
Choose the available sound options among the following table:
Sound Settings
JP9
Onboard Sound: Enable
short
Onboard Sound: Disable
open
Step 8. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5, and then by
shorting pin 1-2 to retain new settings. This jumper can be easily identified by its white
colored cap.
CMOS Clearing
JP5 Setting
Clear CMOS Data
Short pin 2-3 for a
Retain CMOS Data
Short pin 1-2
few seconds to
clear the CMOS
to retain new
settings
2
3
2
3
1
1
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
3
Quick BIOS Setup
After the hardware installation is complete, turn the power switch on, then press the
<DEL> key during the system diagnostic checks to enter the Award BIOS Setup program.
The CMOS SETUP UTILITY will display on screen. Then, follow these steps to complete
the quick BIOS setup.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 3. Select [SAVE & EXIT SETUP]
Press <Enter> to save the new configuration to the CMOS memory, and continue the
boot sequence.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
4
The SOYO CD
Your SY-5SSM Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO
CD contains the user's manual file for your new Motherboard, the drivers software
available for installation, and a database in HTML format with information on SOYO
Motherboards and other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown
below.
(SOYO CD Start Up Program Menu)
The SOYO CD Start Up Program automatically detects which SOYO Motherboard you
own and displays the corresponding model name.
Step 2. Read SOYO [5SSM] Manual
Click the Read Manual button to open the user's manual file of your Motherboard.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Please note that if the Start Up program was unable to determine which SOYO
Motherboard you own, the manual selection menu will pop up, as shown below. Then
select the user's manual file that corresponds to your Motherboard model name and click
OK.
SOYO CD Manuals
Please select your manual In the box below
and click OK.
5SSM
OK
Back
(Manual Selection Menu)
The user's manual files included on the SOYO CD are in PDF (Postscript Document)
format. In order to read a PDF file, the appropriate Acrobat Reader software must be
installed in your system.
Note: The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers and Utilities
Click the Install Drivers button to display the list of drivers software that can be installed
with your Motherboard. The Start Up program displays the drivers available for the
particular model of Motherboard you own. We recommend that you only install those
drivers.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
(Driver Installation Menu)
A short description of all available drivers follows:
SiS 530 VGA drivers
Ø
The SiS VGA driver for windows 95/98 must be installed to make use of your on board
VGA function. (For WinNT read the instructions in back of the Manual)
Ø
SOYO SpeedPro BusMaster Driver for Windows 95/98
Without the busmaster drivers the CPU will need to be involved every time data is read
from or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory
Access) to relieve the CPU of this burden, thus speeding up the system.
The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it
an advantage over other busmaster drivers.
Note: If you install the SOYO SpeedPro busmaster drivers, you can NOT install
the SiS busmaster drivers.
Ø
SiS 530 busmaster drivers
The SiS Busmaster drivers for Windows 95/98 will speed up your harddisk. Only install
ONE type of busmaster driver and first uninstall your previous busmaster drivers before
installing a new version. (For Windows NT read the instructions in the back of the Manual)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
Ø
ESS Windows NT drivers (for PCI)
These are the Windows NT drivers for the on board soundchip. Make sure to first install
these drivers before installing the ESS Soundtrack Program. For the Windows 95/98 ESS
drivers please read the installation steps in the back of this manual.
Ø
ESS Soundtrack Program (for PCI)
With this application program the user can make use of the on board sound chip. Before
installing the ESS Soundtrack Program, you MUST first install the ESS drivers for
Windows 9x or NT.
Ø
SOYO CD Xpress utility
This utility will enhance your CD-ROM Drive data-thoughput by using space on the
Harddisk as cache. This way application programs can access data faster. This utility is
suitable for Windows 95/98.
Select which driver you want to install and click OK, or click Cancel to return to the main
menu. When the installation program of a driver starts running the SOYO-CD will exit.
After finishing the installation, restart the SOYO-CD and install the next driver.
Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the
driver installation program. When the installation is complete, most drivers require to restart your system
before they can become active.
If you want to see all the drivers available on the SOYO –CD, click the Display all drivers on the SOYO
CD button. Do NOT install drivers that are not suitable for your board, otherwise your system may crash.
Step 4. Enter the SOYO CD
Click the Enter SOYO CD button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available in as many as eleven different languages. For your convenience, this
information is available in HTML format, similar to the format widely used on the Internet.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
(SOYO CD HTML Database in English*)
(* The list of menu options may vary between languages)
Note: If no HTML browser is installed on your system, the Start Up program will prompt
you on whether or not you would like to install the Internet Explorer* browser. Click YES to
install the HTML browser. After the installation is complete, please restart your system.
Then re-run the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
5
SiS VGA Driver Installation
Introduction
Your SY-5SSM Motherboard is equipped with the SiS 530 chipset that offers extended
graphics and text modes capabilities. To make use the advanced features of the SiS 530
chipset, you will need to install software drivers and application programs included on the
CD-ROM.
This section describes how to perform the SiS VGA driver installation for Microsoft
Windows NT environment. The Windows 95/98 drivers can be installed automatically
through the SOYO CD. Refer to page 16. For other application programs, and if you are
using an operating system other than WinNT, please refer to the SiS VGA Driver
Installation section in SY-5SSM Motherboard User's Guide and Technical Reference
online manual included on the CD-ROM.
Windows NT Drivers
Driver Files
The enclosed SiS 530 Windows NT drivers files are:
u
u
u
SiS530.INT
SiS530P.SYS
SiS530V.Dll
All the 16-color, 256-color, 32K/64K-color, and 16M-color drivers are available.
Installation
1. Click [Start] menu and select [Control Pane] from Settings group.
2. Select [Display] icon.
3. Select [Settings] index in the display properties sheet.
4. Select [Change Display Type] button.
5. Select [Change …] button in [Adapter Type] group.
6. Select [Have Disk] button.
7. Place CD-ROM disk into the CD drive.
8. When the [Install from Disk] dialog box appears, type the directory storing the
drivers and click [OK]. The directory in the CD-ROM is at
D:\DRIVER\SI530VGA\WINNT40.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
9. The [Select Device] dialog box will appear, showing the driver. Click on [OK] and the
driver will be installed.
10. Select [Close] or [Apply] button from display properties sheet.
11. A message will appear stating you must restart the Windows 95 system, select [Yes]
to restart.
12. After restarting, Windows 95 will run on 640x480x256 color, 75NI.
Selecting Resolution, Color Depth and Refresh Rate
1. Click [Start] menu and select Control Panel from Settings group.
2. Select Display icon.
3. Select Settings.
4. Select Color Palette to change between 16 colors, 256 colors, Hi color, and True
color.
5. To select desktop resolution size, go to the Desktop area and use the slide bar to
change resolution from 640x480, 800x600, 1024x768, and 1280x1024.
6. Select Display Modes.
7. Select value in Refresh rate list box to change the screen refresh rate.
8. Click [OK] or [Apply].
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SY-5SSM Quick Start Guide
6
ESS™ Audio Driver Installation
Windows® 95/98 Sound-Driver Installation
This section describes how to perform the ESS ™ audio driver installation in Windows®
95/98 environment. The Windows NT drivers can be installed automatically through the
SOYO CD. Refer to page 16.
After first installing Windows® 95/98, follow these steps:
1. From the desktop, click [Start] menu and select [Control Panel] from [Settings]
group.
2. Select the [System] icon.
3. Select the [Device Manager] tab; use the scroll bar to locate the following devices
and, if these entries exist, remove them:
Other Devices
?
PCI Multimedia Audio Driver
Sound, Video and Game controllers
ESS ES 1688 Audio Driver
!
.
Note: To remove a device, highlight the item you want to take out from your system
and press the [Remove] button.
4. Then, click [Refresh].
5. Insert the SOYO CD into the CD-ROM drive.
6. When the “Update Driver Wizard” appears, click [Next].
7. The installation wizard will prompt you on the location of the new audio driver you
want to install. Click [Other Location].
8. Click the [Browse] button.
9. Select the “D:\DRIVERS\ESS-PCI\Win9x” path, and click [OK].
10. Now let Windows® 95/98 automatically copy the .inf driver files and configure the
ESS sound chip.
This completes the Windows® 95/98 installation. The program will continue to load and
when it is complete, you should hear the Windows® 95/98 start-up wave file.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Edition: December 98
International Headquarters
Soyo Computer Inc., (Taiwan)
Tel: 886-2-2290-3300
Fax: 886-2-2298-3322
E-mail: [email protected]
Version 1.0
5SSM SERIAL
USA Branch Office
Soyo Tek Inc., (USA)
Tel: (408) 452-7696
Fax: (408) 573-7696
E-mail: [email protected]
SOYO Europe
Soyo Europe B.V., (Holland)
Tel: 31-79-3637500
Fax: 31-79-3637575
E-mail: [email protected]
Germany Branch Office
SAAT Technology GmbH, (Germany)
Tel: 49-(0)441-204044
Fax: 49-(0)441-203422
Email: [email protected]
UK Branch Office
Soyo (U.K.) Ltd.
Tel: 44-(0)181-569 4111
Fax: 44-(0)181-569 4134
E-mail: [email protected]
Japan Branch Office
Soyo Computer (Japan)
Tel: 81-3-33682188
Fax: 81-3-33682199
E-mail: [email protected]
Hong Kong Branch Office
Soyo Hong Kong Ltd. (H.K.)
Tel: 852-2710-9810
Fax: 852-2710-9078
E-mail: [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|