SIIG Computer Hardware 701P48438 User Manual

FireWire800+Hi-Speed  
USB Combo  
Quick Installation Guide  
Introducing the FireWire 800 + Hi-Speed  
USB Combo  
The FireWire 800+Hi-Speed USB Combo features the latest  
technology in FireWire 800 and USB 2.0.  
FeaturesandBenefits  
Combo card design adds five USB 2.0 (480 Mbps),  
one 1394a (400Mbps) and two 1394b (800 Mbps)  
ports into your system.  
Built-in4-pinpowerconnectorprovidesextrapower  
when connected to the system's power supply  
(Recommended)  
Supportshot-swappingandPlug-n-Playconnection  
of peripheral devices  
FireWire 800 (1394b) interface  
Provides 3 FireWire ports for multiple 1394b and  
1394a device connections  
Adds two FireWire 800 (1394b) ports (1 int. + 1 ext.)  
and one external 1394a (400Mbps) port  
Supports IEEE 1394b and backwards compatible  
with 1394a-2000 and 1394-1995 standards  
Supports data transfer rates of 100, 200, 400, and  
800Mbps  
04-0447B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
PackageContents  
FireWire 800+Hi-Speed USB Combo adapter  
"Y" split power cable  
Driver CD  
Quick Installation Guide  
BoardLayout  
1394b (9-pin)  
1394a (6-pin)  
1394b (9-pin)  
USB Pin-out  
Header  
USB 2.0  
Power Connector  
(recommended)  
USB 2.0  
Figure 1. Board Layout  
Note: The Power Connector (same as the one used  
with your floppy disk drive) is designed to provide  
additional power to the board when needed.  
Connectthispowerconnector(recommended)when  
one of the following conditions occur:  
- Device(s) not being detected.  
- All ports are used.  
Power off your system first before making this  
connection.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
USBPin-outHeader  
The internal USB Pin-out Header consists of 9 pins  
arranged in 2 rows; the header provides 2 USB ports.  
Match up +5VDC (Pin 1) on the 4-Pin USB Connector to  
Pin 1 on the pin-out header. Connecting the USB cable  
improperly may damage the system. Please refer to your  
system's manual for proper connection.  
Pin  
1
Assignment  
+5VDC  
Pin  
2
Assignment  
+5VDC  
3
USB- (Data-)  
USB+ (Data+)  
Ground (GND)  
None  
4
USB- (Data-)  
USB+ (Data+)  
Ground (GND)  
Ground (GND)  
5
6
7
8
9
10  
Figure 2. USB Pin-out Header  
Note: The diagram and table shows labeling for a  
typical motherboard 9-pin pin-out header. Please  
notethatthe1stpinonthe5-pinrowoftheFireWire  
800+Hi-Speed Combo is labeled pin1 but  
corresponds to pin 2 on the diagram, nevertheless ,  
the assignment for each pin are identical to the  
table. The pin-out header is designed to connect to  
front mounted USB ports, flash memory card  
readers, or any USB devices that require pin-out  
header connection. Reference the image above and  
review your computer's manual for proper  
connection.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hardware Installation  
General instructions for installing the card are provided  
below. Since the design of computer cases and  
motherboards vary, refer to your computer’s reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer and any  
other connected peripheral devices. Unplug the  
computer's power cord.  
2. Remove your computer’s cover and install the card  
in an available PCI slot.  
3. Push the board down firmly, but gently, until it is  
well seated.  
4. Connect internal connections where needed. See  
Board Layout on page 3 for more details.  
5. Secure the card and replace the cover.  
Figure 3. Inserting the PCI Board  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Windows Driver Installation  
The instructions below are divided into two sections,  
USB 2.0 and FireWire 800. To ensure proper installation  
of this board, please follow the instructions step-by-step.  
USB 2.0 Driver Installation  
For Windows 2000 (with SP4 or later)/XP (with SP1 or  
later)/2003/Vista  
Windows will automatically detect and install it's  
built-in USB 2.0 driver. No additional driver installation  
is needed. The board will operate at USB 2.0 speed.  
For Window 2000 (with SP3 or earlier)  
Windows will automatically detect and install it's  
built- in USB 1.1 driver. The board will operate at USB 1.1  
speed.  
1. At the Found New Hardware Wizard, click Next.  
2.  
Select Search for the best driver..., click Next.  
3. Uncheck all boxes, then click Next.  
4. Select Disable the Device..., then click Finish.  
XP (without SP1)  
Windows will automatically detect and install it's  
built- in USB 1.1 driver. The board will operate at USB 1.1  
speed.  
1. At the Found New Hardware Wizard select Install  
the software automatically, then click Next.  
2. Select No, do not connect to the internet now, then  
click Next.  
3.  
Check Don't prompt me again to install this  
software, then click Finish.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
FireWire 800 Driver Installation  
Windows will automatically install it's built-in FireWire  
400 driver for the FireWire 800 + Hi-Speed USB Combo. To  
get the full speed from the controller, install the FireWire  
800 driver using the directions below.  
Windows2000  
Windows2000automaticallyinstallsit's built-inFireWire  
400 driver for the FireWire 800 + Hi-Speed USB Combo. To  
getthefullspeedoutofthiscontroller,installtheFirewire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup32.exe, click OK. (Change D: to match  
your CD-ROM drive letter)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. At the Destination Location screen, click Next.  
5.  
Select Complete, then click Next.  
6. At the Program Folder screen, click Next.  
7. At the Digital Signature screen, click Yes, then click  
Finish.  
8. Selecttherestartcomputeroption, thenclickFinish.  
32-bitWindowsXP  
Windows XP automatically installs it's built-in 1394a  
driver for the FireWire 800 + Hi-Speed USB Combo. To get  
the full speed out of this controller, install the FireWire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup32.exe, click OK. (Change D: to match  
your CD-ROM drive letter)  
2. At the Welcome screen, click Next.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. At the License Agreement screen, click Yes.  
4. At the Destination Location screen, click Next.  
5.  
Select Complete, then click Next.  
6. At the Program Folder screen, click Next.  
7. At the Software Installation screen, click Continue  
Anyway, then click Finish.  
8. Selecttherestartcomputeroption, thenclickFinish.  
64-bitWindowsXP  
Windows XP automatically installs it's built-in 1394a  
driver for the FireWire 800 + Hi-Speed USB Combo. To get  
the full speed out of this controller, install the FireWire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup64.exe, click OK. (Change D: to match  
your CD-ROM drive letter)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. At the Destination Location screen, click Next.  
5.  
Select Complete, then click Next.  
6. At the Program Folder screen, click Next.  
7. At the Security Alert box, click Yes two times.  
8. At the Software Installation screen, click Continue  
Anyway, then click Finish.  
9. Selecttherestartcomputeroption, thenclickFinish.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
32-bitWindowsServer2003  
Windows Server 2003 automatically installs it's  
built-inFireWire400driverfortheFireWire800+Hi-Speed  
USB Combo. To get the full speed out of this controller,  
installtheFireWire800driverusingthedirectionsbelow.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup32.exe, click OK. (Change D: to match  
your CD-ROM drive letter)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. At the Destination Location screen, click Next.  
5.  
Select Complete, then click Next.  
6. At the Program Folder screen, click Next.  
7. At the Security Alert box, click Yes two times.  
8. At the Software Installation screen, click Continue  
Anyway, then click Finish.  
9. Selecttherestartcomputeroption, thenclickFinish.  
64-bitWindowsServer2003  
Windows Server 2003 automatically installs it's  
built-inFireWire400driverfortheFireWire800+Hi-Speed  
USB Combo. To get the full speed out of this controller,  
installtheFireWire800driverusingthedirectionsbelow.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup64.exe, click OK. (Change D: to match  
your CD-ROM drive letter)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. At the Destination Location screen, click Next.  
5.  
Select Complete, then click Next.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. At the Program Folder screen, click Next.  
7. At the Security Alert box, click Yes two times.  
8. At the Software Installation screen, click Continue  
Anyway, then click Finish.  
9. Selecttherestartcomputeroption, thenclickFinish.  
WindowsVista™  
Windows Vista operating system automatically installs  
it's built-in FireWire 400 driver for the FireWire 800 + Hi-  
Speed USB Combo. To get the full speed out of this  
controller, install the FireWire 800 driver using the  
directions below.  
1. Insert the driver CD. Click Start.  
For32-bitWindowsVista:IntheStartSearchbox,type  
D:\setup32.exe, press Enter. (Change D: to match  
your CD-ROM drive letter)  
For64-bitWindowsVista:IntheStartSearchbox,type  
D:\setup64.exe, press Enter. (Change D: to match  
your CD-ROM drive letter)  
2. Click Allow.  
3. At the Welcome screen, click Next.  
4. At the License Agreement screen, click Yes.  
5. At the Destination Location screen, click Next.  
6.  
Select Complete, then click Next.  
7. At the Program Folder screen, click Next.  
8. At the Windows Security box, click Install three  
times, then click Finish.  
9. Selecttherestartcomputeroption, thenclickFinish.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ToVerifyWindowsInstallation  
1. Check Device Manger to verify installation:  
For 2000/XP/Server 2003: Right click My Computer,  
click Manage, then click Device Manager.  
For Windows Vista: Right click Computer, click  
Manage, click Continue, click Device Manager.  
2. The drivers for this controller show up differently  
under different versions of Windows. Please refer  
to the correct Windows version to verify:  
Windows 2000 (with SP4 or later):  
a) Under Universal Serial Bus Controllers:  
- NEC... Open Host Controller  
- NEC... Open Host Controller  
- Standard Enhanced PCI to USB Host Controller  
- USB 2.0 Root Hub  
- USB Root Hub  
- USB Root Hub  
b) Under 1394 Bus host controllers:  
- Unibrain driver/OHCI Compatible Board or  
IEEE 1394b (FireWire 800) adapter  
Windows2000(withSP3orearlier)andXP(without  
SP1):  
a) Under Universal Serial Bus Controllers:  
- NEC PCI to USB Open Host Controller  
- NEC PCI to USB Open Host Controller  
- USB Root Hub  
- USB Root Hub  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) Under 1394 Bus host controllers:  
- Unibrain driver/OHCI Compatible Board or  
IEEE 1394b (FireWire 800) adapter  
c) Under Other Devices:  
- UniversalSerialBus(USB)Controllerwilldisplay  
with a yellow exclamation mark.  
Windows XP (with SP1 or later)/Server 2003/Vista:  
a) Under Universal Serial Bus Controllers:  
- NEC PCI to USB Open Host Controller  
- NEC PCI to USB Open Host Controller  
- Standard Enhanced... USB Host Controller  
- USB Root Hub  
- USB Root Hub  
- USB Root Hub  
b) Under 1394 Bus host controllers:  
- Unibrain driver/OHCI Compatible Board or  
IEEE 1394b (FireWire 800) adapter  
Mac OS Driver Installation  
The instructions below are divided into two sections,  
USB 2.0 and FireWire 800. To ensure proper installation  
of this board, please follow the instructions step-by-step  
in both sections.  
USBDriverInstallation  
Mac OS 8.6-9.x, OS X (version 10.2.7 and earlier)  
This board will only work at USB 1.1 speed in these OSes.  
Just install the board and Mac OS will automatically  
detect and install the correct USB 1.1 driver for it. No  
additional driver is necessary.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mac OS X (version 10.2.8 ) or later  
Mac OS X (version 10.2.8) or later have built-in USB 2.0  
driver support for this controller. Just install the board  
and Mac OS will automatically detect and install the  
correct drivers for it. No additional driver is necessary.  
FireWireDriverInstallation  
To ensure proper operation of the FireWire 800+Hi-Speed  
USB Combo in your Mac, some Mac OS requires the most  
current Firewire software from Apple. Apple's website  
contains all the information needed to download and  
installFirewiresoftwareupdate. Macsoftwaredownload  
When you are at the download page, in the Search box,  
check Restrict to downloads, type in 1394, then click the  
search button. The information below will help you  
decide whether or not to download and install the latest  
Firewire driver update.  
1.  
Mac OS 10.2.4 or later has built-in Firewire 800  
(1394b) driver support with the operating system.  
No driver installation is needed. The firewire 800  
ports will work up to 800 Mbps.  
2.  
Mac OS 9.1, 9.2.x, and Mac OS 10.1.x-10.2.3 have  
built-inFirewire400(1394a)driversupportwiththe  
operating system. No driver installation isneeded.  
The Firewire 800 ports will work up to 400 Mbps.  
3.  
4.  
Mac OS 9.0.x users should download the Firewire  
software version 2.5 or later. The Firewire 800 ports  
will work up to 400 Mbps.  
Mac OS 8.6 users should download the Firewire  
software version 2.3.3. The Firewire 800 ports will  
work up to 400 Mbps.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To Verify Mac OS Installation  
Since we didn't load any additional driver under these  
Mac OSes, plug in a USB device to verify installation.  
Connecting Devices  
General driver installation steps are provided below.  
Pleasereviewyourdevice'susermanualformoredetails.  
USBDevices  
Windows and Mac OS will automatically detect and  
install most USB devices when connected. For devices  
that do not install automatically, additional drivers may  
be required. Refer to the device's users manual for more  
information.  
FireWireDevices  
For Windows 2000  
1. At the Found New Hardware Wizard, click Next.  
2. SelectSearchforasuitabledriver...,thenclickNext.  
3. Uncheck all check boxes, then click Next.  
4. Click Next, then click Finish.  
For Windows XP  
1. At the Found New Hardware Wizard,  
For XP w/SP2 or later  
Select No, not this time, then click Next.  
For XP w/SP1 or earlier  
Go directly to step #2.  
2. SelectInstalltheSoftwareAutomatically,thenclick  
Next.  
3. Click Continue Anyway. (Skip if not prompted)  
4. Click Finish to complete the installation.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For Server 2003  
1. At the Found New Hardware Wizard,  
For 2003 w/SP1 or later  
Select No, not this time, then click Next.  
For 2003 no service pack installed  
Go directly to step #2.  
2. SelectInstalltheSoftwareAutomatically,then click  
Next.  
3. At the Security Alert box click Yes, or the Hardware  
Installation box click Continue Anyway, then click  
Finish to complete the installation.  
For Windows Vista  
Windows Vista will automatically detect and install the  
drivers for most FireWire devices when connected.  
However, for devices that do not install automatically,  
follow the steps below to complete the installation.  
1. Click Locate and install driver software.  
2. Click Continue to complete the installation.  
For Mac OS  
MacOSwillautomaticallydetectandinstallmostFireWire  
devices when connected. For devices that do not install  
automatically, additional drivers may be required. Refer  
to the device's users manual for more information.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ubSwitch Utility (for Windows only)  
In order to use a DV camcorder with this controller,  
Microsoft's FireWire 400 driver must be installed in the  
system. We have supplied an easy to use utility that  
allows switching between Microsoft's driver and the  
FireWire 800 driver. Before using this utility, unplug all  
devices from the FireWire 800 card.  
1. Click Start, Programs, Unibrain ubcore, Tools then  
ubSwitch.  
2. Right click the ubSwitch icon located in the system  
tray by the clock.  
3. Clickthe1394Adapterthatyouwanttoswitch,then  
click on Microsoft 1394 Drivers.  
Note: If your system has multiple 1394 adapters  
installed, make sure that you click on the 1394  
adapter that the camcorder will be plugged into.  
4. Windows will display an information box when the  
driver is ready for use. It may take a few seconds for  
this box to appear.  
Note: To switch back to the FireWire 800 driver,  
follow the same procedures, but in step 3 instead of  
clickingonMicrosoft1394Drivers,clickonUnibrain  
1394 Drivers.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blank Page  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blank Page  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitour  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit  
questions online and a technical support analysts will promptly  
respond.  
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,anRMAnumberwillbeissued. SIIGRMAdepartment  
can also be reached at (510) 413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
networking, sound cards, and other accessories. SIIG is the premier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retail stores, mail order catalogs, through major  
distributors, system integrators, and VARs in the Americas and the  
UK,andthroughe-commercesites.  
PRODUCT NAME  
FireWire 800 + Hi-Speed USB Combo  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
FireWire800+Hi-SpeedUSBComboisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregistered  
trademarksofSIIG,Inc. Microsoft,WindowsandWindowsVistaareeitherregisteredtrademarksor  
trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a  
registered trademark of Intel Corporation. Mac and Mac OS are registered trademarks of Apple  
Computer,Inc. Othernamesusedinthispublicationareforidentificationonlyandmaybetrademarks  
oftheirrespectivecompanies.  
March, 2008  
Copyright © 2008 by SIIG, Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

SIIG TV Mount 04 0676A User Manual
Sony Car Stereo System CDX 1200 User Manual
Sony DVD Player DVP SR750H User Manual
Sony MiniDisc Player MDS JD320 User Manual
Sony MiniDisc Player ZS M50 User Manual
Sony Portable CD Player ZS S50CP User Manual
Sterling Marine Instruments S 8412 User Manual
SUPER MICRO Computer Computer Hardware X7DBi+ User Manual
Sylvania CRT Television 6427TFY User Manual
SysKonnect Network Card 9821 User Manual