SIIG Computer Hardware 04 0629A User Manual

2S1P Combo-Value  
Quick Installation Guide  
Introducing the 2S1P Combo-Value  
The 2S1P Combo-Value is a total solution for serial and  
parallel device connections. It provides two 16550 UART  
serial ports which supports data transfer rates up to  
16 Mb/s and one ECP/EPP parallel port which supports  
data transfer rates up to 1.5 MB/s.  
FeaturesandBenefits  
CompliantwithPCILocalBusSpecification,Revision  
2.3  
FullsupportforDOS-andWindows-basedsoftware  
PCI IRQ sharing feature reduces IRQ conflicts  
Serialinterface  
Two high-speed 16C550 UART serial ports (9-pin)  
supports baud rate up to 16 Mb/s  
Works with 56K modems, PDAs, and other high  
speed serial devices  
Parallelinterface  
Compliant with IEEE 1284-1994 parallel port  
standard  
Supports ECP, EPP, PS2, and SPP parallel port  
modes  
Works with various types of parallel devices  
including printers, removable drives, scanners,  
CD-R/RWs, and more  
1
04-0629A  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hardware Installation  
General instructions for installing the card are provided  
below. Since the design of computer cases and  
motherboards vary, refer to your computer’s reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computer case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer.  
2. Unplug the power cord and remove the computer's  
cover.  
3. Remove the slot bracket cover from an available PCI  
slot.  
4. Connect the 2-Port DB9 (9-Pin) serial port cable  
connector now and remove another slot bracket  
cover from from the system chassis. See Figure 1 on  
page 2 for more details. Skip this step if you don't  
need any serial ports.  
5. Carefully align the card to the selected PCI slot,  
push the board down firmly, but gently, until it is  
well seated.  
6. Replace the slot bracket holding screw to secure the  
card.  
7. Mount the second serial port and secure it with the  
slot bracket holding screw. Skip this step if you  
don't need any serial ports.  
8. Replacethecomputercoverandreconnectthepower  
cord.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Driver Installation  
This section provides information on how to install the  
2S1P Combo-Value drivers. Please make sure the board is  
installed before proceeding.  
Windows7(32-/64-bit)  
1. Install the board and boot up Windows.  
2.  
Right click Computer, click Manage, click Device  
Manager.  
3. Insert the driver CD. Right click PCI Parallel Port,  
click Update Driver Software.  
4.  
Click Browse my computer for driver software.  
For 32-bit: Type D:\32bit, then click Next. (Change  
D: to match your CD-ROM drive letter)  
For 64-bit: Type D:\64bit, then click Next. (Change  
D: to match your CD-ROM drive letter)  
5. At Windows has successfully updated your driver  
software, click Close.  
6. Right click PCI Serial Port, click Update Driver  
Software.  
7.  
Repeat steps 4-5.  
8. Right click PCI Serial Port, click Update Driver  
Software.  
9. Repeat steps 4-5 to complete the installation.  
WindowsVista(32-/64-bit)  
1. Install the board and boot up Windows.  
2. Insert the driver CD. At the Found New Hardware  
window, insert the driver CD, click Locate and  
install driver software (recommended), then click  
Continue.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Click Don't search online. Skip this step and go  
directly to step 4 if not prompted.  
4. Click I don't have the driver disc. Show me other  
options.  
5. Click Browse my computer for driver software  
(advanced).  
For 32-bit: Type D:\32bit, then click Next. (Change  
D: to match your CD-ROM drive letter)  
For 64-bit: Type D:\64bit, then click Next. (Change  
D: to match your CD-ROM drive letter)  
6. AtThesofwareforthisdevicehasbeensuccessfully  
installed, click Close to complete the installation.  
WindowsXP(32-bit)  
1. At the Found New Hardware Wizard,  
For XP SP1 or earlier: Select Install from a list or  
specific location (Advanced), then click Next.  
For XP SP2 or later: Select No, not this time, click  
Next. Select Install from a list or specific location  
(Advanced), then click Next.  
2. Insert the driver CD, check Include this location in  
the search, uncheck the other box, type D:\32bit,  
thenclickNext. (ChangeD:tomatchyourCD-ROM  
drive letter)  
3. Click Finish to complete the installation.  
WindowsXP(64-bit)  
1. AttheFoundNewHardwareWizard,selectNo,not  
this time, click Next.  
2. Select Install from a list or specific location  
(Advanced), click Next.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Insert the driver CD, check Include this location in  
the search, uncheck the other box, type D:\64bit,  
click Next. (Change D: to match your CD-ROM  
drive letter)  
4. Click Finish to complete the installation.  
WindowsServer2003(32-bit)  
1. At the Found New Hardware Wizard.  
For Server 2003 SP1 or later: Select No, not this time,  
click Next. Select Install from a list or specific  
location (Advanced), then click Next.  
For Server 2003: Select Install from a list or specific  
location (Advanced), then click Next.  
2. Insert the driver CD, check Include this location in  
the search, uncheck the other box, type D:\32bit,  
thenclickNext. (ChangeD:tomatchyourCD-ROM  
drive letter)  
3. Click Finish to complete the installation.  
Windows Server 2003 (64-bit )  
1. AttheFoundNewHardwareWizard,selectNo,not  
this time, click Next.  
2. Select Install from a list or specific location  
(Advanced), click Next.  
3. Insert the driver CD, check Include this location in  
the search, uncheck the other box, type D:\64bit,  
click Next. (Change D: to match your CD-ROM  
drive letter)  
4. Click Finish to complete the installation.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
WindowsServer2008(32-bit)  
1.  
AtFoundNewHardwarewindow,clickLocateand  
install driver software (recommended).  
2. Click Don't search online.  
3. Click I don't have the disc. Show me other options.  
4.  
Click Browse my computer for driver software.  
5. InsertthedriverCD. TypeD:\32bit,thenclickNext.  
(Change D: to match your CD-ROM drive letter)  
6. Click Close to complete the installation.  
WindowsServer2008(64-bit)  
1.  
AtFoundNewHardwarewindow,clickLocateand  
install driver software (recommended).  
2. Click I don't have the disc. Show me other options.  
3. Click Browse my computer for driver software.  
4. InsertthedriverCD. TypeD:\64bit,thenclickNext.  
(Change D: to match your CD-ROM drive letter)  
5. Click Close to complete the installation.  
Windows2000  
1. At the Found New Hardware Wizard, click Next.  
2. Select Search for a suitable driver for my device  
(Recommended), then click Next.  
3. SelectSpecifythelocation,unchecktheotherboxes,  
then click Next.  
4. InsertthedriverCD, typeinD:\2000, thenclickOK.  
(Change D: to match your CD-ROM drive letter)  
5. Click Next, then click Finish.  
6. Click Yes to restart to complete the installation.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
WindowsME  
1. Atthe Add New Hardware Wizard, chooseSpecify  
the location of the driver (Advanced), then click  
Next.  
2. Check Specify a location, uncheck the other box,  
insertthedriverCD,typeinD:\ME,thenclickNext.  
(Change D: to match your CD-ROM drive letter)  
3.  
Click Next, then Finish.  
4. Click Yes to restart Windows, when resumes the  
driver will install automatically.  
Windows98SE/98  
1. At the Add New Hardware Wizard, click Next.  
2. Select Search for the best driver for your device  
(Recommended), then click Next.  
3. Select Specify a location, uncheck the other boxes,  
insertthedriverCD,typeinD:\ME,thenclickNext.  
(Change D: to match your CD-ROM drive letter)  
4. Click Next, then click Finish.  
5. Click Yes to restart Windows, when Windows  
resumes the driver will install automatically.  
Windows95  
1. At the Update Device Driver Wizard, click Next.  
2. Insert the driver CD. Click Other Locations.  
3. Type D:\ME, click OK, then click Finish. (Change  
D: to match your CD-ROM drive letter)  
4. At the Insert Disk window, click OK. When the  
Copying Files dialog box appears, type in D:\ME,  
then click OK. (Change D: to match your CD-ROM  
drive letter)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Click Yes to restart Windows.  
6. When Windows resumes the driver will install  
automatically.  
7. Click Yes to restart to complete the installation.  
ToVerifyWindowsInstallation  
Windows 7 (32-/64-bit)  
1. Right click Computer, click Manage, then click  
Device Manger.  
2. Double click Ports (COM & LPT), one PCI ECP  
Parallel Port... and two High-Speed PCI Serial  
Port... should be listed.  
Windows Vista (32-/64-bit)  
1. RightclickComputer,clickManage,clickContinue,  
then click Device Manger.  
2. Double click Ports (COM & LPT), one PCI ECP  
Parallel Port... and two High-Speed PCI Serial  
Port... should be listed.  
Windows XP (32-/64-bit) / Server 2003 (32-/64-bit) / 2000  
1. Right click My Computer, click Manage, then click  
Device Manger.  
2. Double click Ports (COM & LPT), one PCI ECP  
Parallel Port... and two High-Speed PCI Serial  
Port... should be listed.  
Windows Server 2008 (32-/64-bit)  
1. Right click Computer, click Manage, double click  
Diagnostics, then click Device Manager.  
2. Double click Ports (COM & LPT), one PCI ECP  
Parallel Port... and two High-Speed PCI Serial  
Port... should be listed.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Windows ME / 98SE / 98 / 95  
1. Right click My Computer, click Properties, click  
Device Manager.  
2. DoubleclickPorts(COM&LPT), andoneM65-PCI  
ECP Parallel Port... two M65-PCI Serial Port...  
should be listed.  
DOS  
1. Insert the driver CD. From the C:\> prompt, type  
copy D:\dos\*.*, and press Enter. (Change D: to  
match your CD-ROM drive letter)  
2. Type edit autoexec.bat, and press Enter.  
3. Add C:\Gemdosin.exe -a -r at the bottom of the  
Autoexec.bat file.  
4. Go to File, save the changes and exit.  
5.  
Restart your system for the new setup to take effect.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitour  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit  
questions online and a technical support analysts will promptly  
respond.  
SIIGoffersa2-yearmanufacturerwarrantywiththisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased it.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. Your RMA request will be processed, if the  
product is determined to be defective, an RMA number will be  
issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity  
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,  
and legacy I/O adapters) that bridge the connection between Desktop/  
Notebook systems and external peripherals. SIIG continues to grow by  
adding A/V and Digital Signage connectivity solutions to our extensive  
portfolio. AllcenteredaroundthedistributionandswitchingofA/Vsignals  
overCAT5/6,theseproductsincludematrixswitches,distributionamplifiers,  
extenders, converters, splitters, cabling, and more.  
SIIG is the premier one-stop source of upgrades and is committed to  
providinghighqualityproductswhilekeepingeconomicalandcompetitive  
prices. High-quality control standards are evident by one of the lowest  
defective return rates in the industry. Our products offer comprehensive  
user manuals, user-friendly features, and most products are backed by a  
lifetime warranty.  
SIIG products can be found in many computer retail stores, mail order  
catalogs, and e-commerce sites in the Americas, as well as through major  
distributors, system integrators, and VARs.  
PRODUCT NAME  
2S1PCombo-Value  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
2S1PCombo-ValueisatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarksofSIIG,  
Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names  
usedinthispublicationareforidentificationonlyandmaybetrademarksoftheirrespectiveowners.  
May, 2010  
Copyright © 2010 by SIIG, Inc. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Sharp All in One Printer AL 2020 User Manual
Sharp CD Player MD MT866H User Manual
Sony CD Player CD X1500 User Manual
Sony Computer Monitor PLM S700E User Manual
Sony Digital Photo Frame DPF D1010 User Manual
Sony Speaker SA 32SE1 User Manual
Sony Universal Remote RM MC60 User Manual
Sunbeam Mixer 2484 User Manual
Sylvania CD Player SRCD2730 User Manual
TANDBERG Network Card D1412802 User Manual