Serial ATA 4-Channel PCI
Quick Installation Guide
Introducing the Serial ATA 4-Channel PCI
The Serial ATA 4-Channel PCI is an ultra high-speed four
channel Serial ATA controller for use in Pentium-class
computers. It achieves burst data transfer rates up to
150MB/ s (1.5Gb/ s) and supports various brand of hard
disk drives with capacities greater that 137GB.
Features and Benefits
•
•
•
Compliant with Serial ATA Specification, rev 1.0
Compliant with PCI Specification, revision 2.2
Provides four independent channels to support up
to four Serial ATA drives
•
Features independent 256-byte FIFOs per channel
for host reads and writes
•
•
•
•
Co-exists with on-board Ultra ATA controller
Features Watch Dog timer for fault resiliency
Supports 32-bit wide PCI bus at 66MHz
Lower pin count and voltage requirement, plus
better cabling over traditional Parallel ATA make
Serial ATA the controller of the future
System Requirements
•
•
Pentium-class computer with one available PCI slot
Windows 98/ 98SE/ ME/ NT 4.0/ 2000/ XP/ Server
2003
•
CD-ROM drive (for driver installation)
1
04-0322B
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Remove your computer’s cover and install the card
in an available PCI slot.
Push the board down firmly, but gently, until it is
well seated. Install a slot bracket holding screw to
secure the card.
•
Now go to Device Connection to connect your
Serial ATA hard disk drive(s).
DeviceConnection
If you plan to use more than two Serial ATA channels,
you will need to purchase additional Serial ATA data
and power cables.
1. Install hard disk drive(s) into chassis.
2. Connect the SerialATA hard disk drive to the system
power supply using the Serial ATA power cable.
3. Connect one end of the Serial ATA cable to the hard
disk drive.
Serial ATA cable
Serial ATA power cable
Figure 3. Hard disk drive connections
4. Attach the other end of the Serial ATA cable to the
Serial ATA connector on the board.
5. Follow the same instructions when connecting
additional hard drives. Device connection is now
complete.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If you like to monitor disk activity of the
SerialATA hard drives,you may at this time connect
the hard disk LED of the system case to the Hard
Disk LED Pins on the Serial ATA controller, see
figure 1, on page 2 for the location of the pins. For
most systems connect the red wire to the pin farthest
from the mounting bracket.
6. Replacethecomputer cover and reconnect thepower
cord. Go to Software Installation to installthe Serial
ATA 4-Channel PCI device driver.
Software Installation
This section provides information on how to install the
Serial ATA 4-Channel PCI drivers for the following
operating systems:
New & Existing Windows 98/ 98SE
New & Existing Windows ME
New & Existing Windows NT 4.0
New & Existing Windows 2000
New & Existing Windows XP/ Server 2003
Windows 98/98SE Driver Installation
For New Windows 98 Installation
1. Install the board and follow Microsoft procedures
to install Windows 98 accordingly.
2. Once Windows has been installed, right click My
Computer and click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Insert the driver CD and click Next.
6. Select Search for a better driver ... and click Next.
7. Check CD-ROM drive, uncheck the other boxes,
then click Next. Click Next again, then Finish.
8. Click Yes to restart Windows to complete the driver
installation.
For Existing Windows 98 Installation
1. Install the board and boot up Windows 98.
2. At the Add New Hardware Wizard, click Next.
3. Select Search for the best driver for your device and
click Next.
4. Insert thedriver CD,check CD-ROM drive,uncheck
the other boxes, then click Next.
5.
Click Next, then Finish.
6. Remove the driver CD and restart Windows to
complete the driver installation.
Windows ME Driver Installation
For New Windows ME Installation
1. Install the board and follow Microsoft procedures
to install Windows ME accordingly.
2. Once Windows has been installed, right click My
Computer, then click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
5. Insert the driver CD, select Automatic search for a
better driver (Recommended), then click Next.
6. Accept the selected driver, then click OK.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Click Finish, then click Yes to restart Windows to
complete the driver installation.
For Existing Windows ME Installation
1. Install the board and boot up Windows ME.
2. At the Add New Hardware Wizard,insert the driver
CD.
3. Select Au tom atic search for a b etter d river
(Recommended), then click Next.
4. Accept the selected driver, then click OK.
5. Click Finish, then restart Windows to complete the
driver installation.
Verify Proper Installation for Windows 98/ME
1. Right-click My Computer, then click Properties.
Select Device Manager tab.
2. Double click SCSI controllers and Silicon Image
SiI 3114 ... Controller should be listed.
3. Highlight Silicon Image SiI 3114 ... Controller and
click Properties. A message This device is working
properly is displayed in the dialog box, the driver
has been correctly installed. If an error message is
displayed, remove Silicon Image SiI 3114 ...
Controller and restart your system.
Windows NT4.0 Driver Installation
A new installation of Windows NT requires a floppy disk
for the driver installation. To make this floppy disk, copy
the contents ofthe Floppy folder,found on the driver CD,
onto a blank floppy disk then follow the directions below.
For New Windows NT4.0 Installation
1. Install the board and follow Microsoft procedures
to install Windows NT4.0 accordingly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. At the Windows NT Setup screen, press F6 to
specify and add the driver.
3. Press S, select Other, then press Enter.
4. Insert the driver diskette and press Enter.
5. Select Silicon Image SiI 3114 ... Controller for
Windows NT 4.0 and 2000, and press Enter.
6. Press Enter to continue and follow on-screen
instru ctions to com p lete Wind ow s N T4.0
installation.
For Existing Windows NT4.0 Installation
1. Install the board and boot up Windows NT4.0.
2. Double click My Computer/ Control Panel/SCSI
Adapters, then click the Drivers tab.
3. Click Add … then Have Disk ....
4. Insert the driver CD, type in D:, then click OK.
(Assuming D: is your CD-ROM drive)
5. Highlight Silicon Image SiI 3114 ... Controller and
click OK.
6. Click OK, remove the driver CD and restart NT to
complete the driver installation.
Verify Proper Installation for Windows NT4.0
1. Double click My Computer/Control Panel/SCSI
Adapters.
2. Highlight Silicon Image SiI 3114... Controller from
SCSI Adapters listing and click Properties. A
message This device is working properly is displayed
in the dialog box, the driver has been correctly
installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 2000 Driver Installation
A new installation of Windows 2000 requires a floppy
disk for the driver installation. To make this floppy disk,
copy the contents of the Floppy folder, found on the
driver CD, onto a blank floppy disk then follow the
directions below.
For New Windows 2000 Installation
1. Install the board and follow Microsoft procedures
to install Windows 2000 accordingly.
2. Restart your system w hen prompted d uring
Windows' installation.
3. At the Windows 2000 Setup screen, press F6 to
install the driver.
4. Insert the driver diskette. Press S, then press Enter.
5. Select Silicon Image SiI 3114 ... Controller for
Windows NT 4.0 and 2000, and press Enter.
6. Press Enter to continue and follow on-screen
instructions to complete the installation.
For Existing Windows 2000 Installation
1. Install the board and boot up Windows 2000.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended) and click Next.
4. Insertthedriver CD,checkCD-ROM drives,uncheck
the other boxes, and click Next. Click Next again to
continue.
Note: Ifa warning message pops up, click Continue
Anyway, then click Finish. Our driver has been
thoroughly tested in Windows for stability.
5. Click Finish, remove the driver CD and restart
Windows to complete the driver installation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WindowsXP/Server2003DriverInstallation
A new installation of Windows XP/ Server 2003 requires
a floppy disk for the driver installation. To make this
floppy disk, copy the contents of the Floppy folder,
found on the driver CD, onto a blank floppy disk then
follow the directions below.
For New Windows XP/Server 2003 Installation
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. Restart your system when prompted by Windows'
installation.
3. At the Windows Setup screen, press F6 to install the
driver.
4. Insert the driver diskette. Press S then press Enter.
5. Select Silicon Image SiI 3114 ... for Windows
XP/Server 2003, then press Enter.
6. Press Enter to continue and follow on-screen
instructions to complete Windows installation.
Note: If a Hardware Installation warning pops up,
click Yes. Our driver has been thoroughly tested in
Windowsfor stability.
For Existing Windows XP/Server 2003 Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, insert the
driver CD, select Install the software automatically
(Recommended), then click Next.
3. Accept the selected driver, then click Next.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Ifa warning message pops up, click Continue
Anyway, then click Finish. Our driver has been
thoroughly tested in Windows for stability.
4. Remove the driver CD and restart Windows to
complete the driver installation.
VerifyProperInstallationforWindows2000/XP/
Server2003
1. Right click My Computer and click Manage.
2. Select Device Manager.
3. Double click SCSI and RAID controllers, then
double click Silicon Image SiI 3114 ... Controller to
display driver properties.
4. A message Thisdeviceisworkingproperlyis displayed
in the dialog box, the driver has been correctly
installed.
Bios Configuration
The SerialATA4-ChannelPCIBIOS willappear everytime
your system starts up. If the bios doesn't show, please try
your controller in another PCI slot. During this (Post)
process, the bios will show up and indicate the devices
attached to it.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
Q UESTIO N S?
SIIG’s O n lin e Su p p ort has answ ers!
Simply visit our website at www.siig.com and click on Support.
Our online support database is updated daily with new drivers
and solutions. Answers to your questions could be just a few clicks
away. You can also submit questions online and one ofour technical
support analysts will promptly respond.
A lifetime manufacturer warranty supplied with this product is
offered by SIIG, Inc. Please see SIIG website for more warranty
details. If you should happen to encounter any problems with this
product, please follow the procedures below.
If it is within the store's return policy period, please return the
product to the store where you purchased from.
If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective,an RMA number willbe issued. SIIG RMA department
can also be reached at (510)413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost ofshipping the product to SIIG
at the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S and International Economy outside of the U.S at
no cost to the customer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/ O connectivity products,including PCI&ISA serialand parallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/ b),
Networking,Sound Cards,and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIG productsoffer comprehensiveuser manuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retailstores,mailorder catalogs,and e-commerce
sitesin theAmericasand theUK,aswellasthrough major distributors,
system integrators, and VARs.
PRODUCT NAME
Serial ATA 4-Channel PCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152
Serial ATA 4-Channel PCI is a trademark of SIIG, Inc.
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are
registered trademarksofMicrosoftCorporation. Pentium isaregistered trademarkofIntelCorporation.
Other names used in publication are for identification only and may be trademarks
oftheir respectivecompanies.
February, 2005
Copyright ©2005 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|