Serial ATA PCI
Quick Installation Guide
Introducing the Serial ATA PCI
The Serial ATA PCI is an ultra high-speed dual channel
Serial ATA controller board for use in Pentium-class
computers. It achieves burst data transfer rates up to
150MB/s (1.5Gb/s) and supports various brand of hard
disk drives with capacities greater that 137GB.
FeaturesandBenefits
•
•
Add up to two high-speed SATA hard drives
New Serial ATA cable - easier to install & provides
better air circulation
•
•
•
Compliant with Serial ATA 1.0 specification
Compliant with PCI 2.3 specification
Supports data transfer rate up to 1.5Gb/s
(150MB/s)
•
•
Two independent bus master DMA channels with
256-byteFIFOsperchannelforhostreadsandwrites
Breaksthe137GBbarrier!Workswithvariousbrands
of large capacity Serial ATA hard disk drives
SystemRequirements
•
Pentium® or equivalent PC with an available PCI
slot
•
Windows® 98SE / ME / NT4.0 / 2000 / XP (32-/64-
bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/
64-bit)
1
04-0265F
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove the computer cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card bus
connector to the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
6. Replace the slot bracket holding screw to secure the
card.
DeviceConnection
TheSerialATAPCIisadualchannelSerialATAcontroller
that supports up to two Serial ATA hard disk drives. If
you plan to use the second Serial ATA channel, you will
need to purchase another Serial ATA cable.
1. Install hard disk drive(s) in chassis.
2. ConnecttheSerialATAharddiskdrivetothesystem
power supply using the Serial ATA power cable.
3. Connect one end of the Serial ATA cable to the hard
disk drive.
Serial ATA cable
Serial ATA power
cable
Figure 2: Hard disk drive connecrions
4. Attach the other end of the Serial ATA cable to the
Serial ATA connector on the Serial ATA PCI.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial ATA
cable
Figure 3. Connecting the Serial ATA cable
5. Follow the same instructions when connecting a
second hard drive. Device connection is now
complete.
6. Replacethecomputercoverandreconnectthepower
cord.
Driver Installation
This section provides information on how to install the
Serial ATA PCI drivers.
Windows98SE
For New Windows 98SE Installation
1. Install the board and follow Microsoft procedures
to install Windows 98SE accordingly.
2. Once Windows has been installed, right click My
Computer and click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
5. Insert the driver CD and click Next.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select Search for a better driver..., then click Next.
7. Check Specify a location, uncheck the other boxes,
then click Next.
8. Click Next, then click Finish.
9. Remove the driver CD and restart Windows to
complete the installation.
For Existing Windows 98SE Installation
1. Install the board and boot up Windows.
2. At the Add New Hardware Wizard, click Next.
3. SelectSearchforthebestdriverforyourdeviceand
click Next.
4. Insert the driver CD, check Specify a location,
uncheck the other boxes, type D:\98SE, then click
Next. (Change D: to match the drive letter of your
CD-ROM)
5.
Click Next, then Finish.
6. Remove the driver CD and restart Windows to
complete the installation.
WindowsME
For New Windows ME Installation
1. Install the board and follow Microsoft procedures
to install Windows ME accordingly.
2. Once Windows has been installed, right click My
Computer, then click Properties. Select Device
Manager tab.
3. Double click PCI Mass Storage Controller listed
under Other Devices.
4. Select Driver tab, then click Update Driver button.
5. Insert the driver CD, select Specify the location of
the driver (Advanced), then click Next.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Check Specify a location, uncheck the other box,
type D:\ME, click Next. (Change D: to match the
drive letter of your CD-ROM)
7. ClickNext, thenclickFinish. RemovethedriverCD
and restart Windows to complete the installation.
For Existing Windows ME Installation
1. Install the board and boot up Windows ME.
2. AttheAddNewHardwareWizard,insertthedriver
CD.
3. SelectSpecifythelocationofthedriver(Advanced),
then click Next.
4. Check Specify a location, uncheck the other box,
type D:\ME, click Next. (Change D: to match the
drive letter of your CD-ROM)
5. Click Next, then click Finish.
6. Remove the driver CD and restart Windows to
complete the installation.
ToVerifyWindows98SE/MEInstallation
1. Right-click My Computer, then click Properties.
Select Device Manager tab.
2. Double click SCSI controllers, Silicon Image SiI...
Controller should be listed.
3. Double click Silicon Image SiI... Controller and
click Properties. A message This device is working
properly is displayed in the dialog box when the
driver is correctly installed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WindowsNT4.0
For New Windows NT4.0 Installation
A new installation of Windows NT4.0 requires a floppy
disk for the driver installation. To make this floppy disk,
copy the contents of the NT4 folder, found on the driver
CD, onto a blank floppy disk then follow the directions
below.
1. Install the board and follow Microsoft procedures
to install Windows NT4.0 accordingly.
2. At the Windows NT Setup screen, press F6 to
specify and add the driver.
3. Press S, select Other, then press Enter.
4. Insert the driver diskette then press Enter.
5.
Select Silicon Image... for Windows NT 4.0 and
2000 and press Enter.
6. Press Enter to continue, then follow the on-screen
instructions to complete Windows NT4.0
installation.
For Existing Windows NT4.0 Installation
1. Install the board and boot up Windows NT4.0.
2. Double click My Computer/Control Panel/SCSI
Adapters, then click the Drivers tab.
3. Click Add..., then click Have Disk....
4. Insert the driver CD, type D:\NT4, then click OK.
(Change D: to match the drive letter of your
CD-ROM)
5. Highlight Silicon Image in the left column, then
select Silicon Image SiI... SATALink Controller,
and click OK.
6. ClickOK,removethedriverCDandrestartNT4.0to
complete the installation.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ToVerifyWindowsNT4.0Installation
1. Double click My Computer/Control Panel/SCSI
Adapters.
2. Highlight Silicon Image... Controller from SCSI
Adapters listing and click Properties. A message
This device is working properly is displayed in the
dialog box when the driver is correctly installed.
Windows2000
For New Windows 2000 Installation
A new installation of Windows 2000 requires a floppy
disk for the driver installation. To make this floppy disk,
copy the contents of the Floppy folder, found on the
driver CD, onto a blank floppy disk then follow the
directions below.
1. Install the board and follow Microsoft procedures
to install Windows 2000 accordingly.
2. Restart your system when prompted during
Windows' installation.
3. At the Windows 2000 Setup screen, press F6 to
install the driver.
4. Insert the driver diskette. Press S, then press Enter.
5. Select Silicon Image SiI... Controller and press
Enter.
6. Press Enter to continue and follow on-screen
instructions to complete the installation.
For Existing Windows 2000 Installation
1. Install the board and boot up Windows 2000.
2. At the Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommended) and click Next.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. InsertthedriverCD,checkCD-ROMdrives,uncheck
the other boxes, and click Next. Click Next again to
continue.
5. Click Finish, remove the driver CD and restart
Windows to complete the installation.
WindowsXP/Server2003(32-bit)
For New Windows XP/Server 2003 Installation
A new installation of Windows XP/Server 2003 requires
a floppy disk for the driver installation. To make this
floppy disk, copy the contents of the Floppy folder,
found on the driver CD, onto a blank floppy disk then
follow the directions below.
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. Restart your system if prompted by Windows
installation.
3. At the Windows Setup screen, press F6 to install the
driver.
4. Insert the driver diskette. Press S then press Enter.
5. Select Silicon Image SiI... Controller and press
Enter.
6. Press Enter to continue and follow the on-screen
instructions to complete the installation.
For Existing Windows XP/Server 2003 Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard:
XP (w/SP1 or earlier)/Server 2003: continue to step #3
XP (w/SP2 or later)/Server 2003 (w/ SP1 or later): select
No, not at this time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended), and click Next.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click Finish and restart Windows to complete the
installation.
Windows XP /Server 2003 (64-bit)
For New Windows XP/2003 Installation
A new installation of Windows XP 64-bit/Server 2003
64-bit requires a floppy disk for the driver installation.
To make this floppy disk, copy the contents of the 64bit
folder, found on the driver CD, onto a blank floppy disk
then follow the directions below.
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. Restart your system when prompted by Windows
installation.
3. At the Windows Setup screen, press F6 to install the
driver.
4.
Insert the floppy disk you made above. Press S then
press Enter.
5. Select Silicon Image SiI 3512... that matches your
system processor, then press Enter.
6. Press Enter to continue and follow the on-screen
instructions to complete the installation.
For Existing Windows XP/2003 Installation
1. Install the board and boot up Windows.
2. AttheFoundNewHardwareWizard,selectNo,not
at this time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended), and click Next.
4. Click Finish and restart Windows to complete the
installation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ToVerifyWindows2000/XP/2003Installation
1. Right click My Computer and click Manage.
2. Select Device Manager.
3. Double click SCSI and RAID Controllers, Silicon
Image SiI 3512... Controller should be displayed.
WindowsVista™(32-bit)
For New Windows Vista Installation
1. Install the board and follow Microsoft procedures
to install Windows Vista accordingly.
2. At the Where do you want to install Windows?
screen, click Load Driver.
3. Insert the driver CD, then click OK.
4. Select Silicon Image SiI... SATALink Controller...,
then click Next.
5. Follow the on-screen instructions to complete the
Windows Vista installation.
For Existing Windows Vista Installation
1. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
2. Click Continue, insert the driver CD, click Next.
3. Click Close to complete the installation.
WindowsVista(64-bit)
For New Windows Vista 64-bit Installation
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. At Where do yo want to install Windows? screen,
click Load Drivers.
3. Insert the driver CD, click Browse.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Clickonthe Plus(+)signnexttotheCD-ROMdrive,
then double click the 64bit folder.
5. Highlight AMD64 (for 64-bit extended processors)
or IA64 (for 64-bit Intel Itanium processors), then
click Ok.
6. Select Silicon Image... SATALink Controller, then
press Next.
7. Follow the on-screen instructions to complete the
installation.
For Existing Windows Vista 64-bit Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, select Locate
and install driver software (recommended), click
Continue.
3. Insert the driver CD, click Next.
4. Click Close to complete the installation.
To Verify Windows Vista Installation
1. Right click My Computer and click Manage.
2. Click Continue, click Device Manager.
3. Double click Storage controllers, Silicon Image
SiI... Controller should be displayed.
WindowsServer2008(32-bit)
New Windows 2008 Installation
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. At Where do you want to install Windows?, click
Load Driver.
3. Insert driver CD, then click Browse.
4. Click CD Drive...Drivers, then click OK.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select Silicon Image Sil 3512 SATALink
Controller..., then click OK
6. Followon-screeninstructionstocompleteWindows
Server 2008 installation.
Existing Windows 2008 Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, select Locate
and install driver software (Recommended), then
click Don't search online.
3. Insert the driver CD. The driver will install
automatically.
4.
Click Close.
5. Remove the driver CD and restart your Windows to
complete the installation.
WindowsServer2008(64-bit)
New Windows 2008 Installation
1. Install the board and follow Microsoft procedures
to install Windows accordingly.
2. At Where do you want to install Windows?, click
Load Driver.
3. Insert driver CD, then click Browse.
4. Double click CD Drive (D:). (change D: to match
your CD-ROM drive letter)
5. Double click 64bit folder, highlight AMD64 (for 64-
bit extended processors) or IA64 (for 64-bit Intel
Itanium processors), then click Ok.
6. Select Silicon Image Sil 3512 SATALink
Controller..., then click Next.
7. Followon-screeninstructionstocompleteWindows
Server 2008 installation.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Existing Windows 2008 Installation
1. Install the board and boot up Windows.
2. At the Found New Hardware Wizard, select Locate
and install driver software (Recommended), then
click Don't search online.
3. Insert the driver CD. The driver will install
automatically.
4.
Click Close.
5. Remove the driver CD and restart your Windows to
complete the installation.
VerifyServer2008Installation
1. Right click Computer, click Manage, double click
Diagnostics, click Device Manager.
2. Double click Storage controllers, Silicon Image
SiI... Controller should be displayed.
Bios Configuration
The Serial ATA PCI BIOS will appear everytime your
system starts up. If the bios doesn't show, please install
your controller in another PCI slot. During this (Post)
process, the bios will show up and indicate the devices
attached to it.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’sOnlineSupporthasanswers! Simplyvisitour
database is updated daily with new drivers and solutions. Answers
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA#:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,andthroughe-commercesites.
PRODUCT NAME
SerialATAPCI
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Ph: 510-657-8688
Serial ATA PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG,
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of
MicrosoftCorporationintheUnitedStatesand/orothercountries. Pentiumisaregisteredtrademark
of Intel Corporation. Other names used in this publication are for identification only and may be
trademarksoftheirrespectivecompanies.
March, 2009
Copyright © 2009 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|