HCT300 325-1410 12/17/03 9:50 AM Page 1
™
by
Instruction Manual
Manual de Instrucciones
Directives
HCT300
CHCT300
Download from Www.Somanuals.com. All Manuals Search And Download.
HCT300 325-1410 12/17/03 9:50 AM Page 3
• Do not operate the unit with a missing or damaged wire safety guard,
safety glass lens (lamp containment), or UV filter.
• Do not direct the light at persons or look directly at lighted fixture.
• Use only with a 300 watt or smaller bulb. Installing a bulb of a higher
wattage could create a fire hazard or risk of burns. Use of a higher
wattage bulb will void the product warranty.
• Never touch the bulb with your bare hands. Oil from your skin can
cause premature failure. Always handle the bulb with gloves or a soft
cloth.
• If lens is replaced, use only a diffused tempered safety glass of
equal thickness.
• For maximum bulb life, position light so that the halogen bulb remains
within 4° of horizontal.
• Disassembly of your fixture will void the warranty.
• Use only with three wire extension cords that have three-prong
grounding plugs and that are suitable for outdoor use, such as cords
marked SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A,
SJW, SJW-A, SJOW, SJOW-A, SJTW, SJTW-A, SJTOW, SJTOW-A
and grounding receptacles that accept a three-prong plug. When the
fixture is used in wet locations, Ground Fault Circuit Interruption
(GFCI) protection must be provided on the circuit(s) or outlet(s) to be
used. Receptacles are available having built-in GFCI protection and
are able to be used for this measure of safety.
WARNING: Deviation from the assembly instructions may result in a
risk of fire or electric shock.
SAVE THESE INSTRUCTIONS
Replacing the bulb
Step 1: Loosen the screw located at the top of the fixture recessed
inside the outer shell.
Step 2: Open door frame assembly for easy access to the bulb.
Step 3: Using gloves or a soft cloth, press the bulb to one side of the
socket as indicated on the metal reflector. Remove opposite
end of bulb from the other side of the socket. Reverse this
procedure to install a new replacement bulb.
How to use
The fixture is packed in a compact storage position. Remove the fixture
from the carton. Loosen the knobs on the sides of the fixture and
swing the fixture up so that the lens guard is directly above the closed
or curved portion of the tubular steel stand. Retighten the knobs.
Aiming the fixture
Loosen the knobs located on the sides of the fixture housing. Using the
top carrying handle, tilt to desired position, then retighten knobs. There
is a stop designed in the stand assembly which restricts downward aim-
ing of the fixture for safety reasons. To prevent over-heating and risk of
burns or fire, do not aim the fixture down at an angle of more than 10
degrees from horizontal.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HCT300 325-1410 12/17/03 9:50 AM Page 4
Two year limited warranty
Cooper Lighting (“the Company”) warrants this product (“the product”) against
defects in material or workmanship for a period of two years from date of orig-
inal purchase, and agrees to repair or, at the Company’s option, replace a
defective product without charge for either replacement parts or labor during
such time. This does not include labor to remove or install fixtures.
This warranty is extended only to the original purchaser of the product. A pur-
chasers receipt or other proof of date of original purchase acceptable to the
Company is required before warranty performance shall be rendered.
This warranty only covers product failure due to defects in materials or work-
manship which occurs in normal use. It does not cover the bulb or failure of
the product caused by accident, misuse, abuse, lack of reasonable care, alter-
ation, or faulty installation, subjecting the product to any but the specified
electrical service or any other failure not resulting from defects in materials or
workmanship. Damage to the product caused by separately purchased, non-
Company brand replacement bulbs and corrosion or discoloration of brass
components are not covered by this warranty.
There are no express warranties except as described above.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL
IMPLIED WARRANTIES, IF ANY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRAN-
TY. Some states do not allow the exclusion or limitation of incidental or con-
sequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you.
No other warranty, written or verbal, is authorized by the Company. This war-
ranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please write to Cooper Lighting, 1121 Highway 74
South, Peachtree City, GA 30269. Enclose product model number and prob-
lems you are experiencing, along with your address and telephone number.
You will then be contacted with a solution, or a Return Goods Authorization
number and full instructions for returning the product. All returned products
must be accompanied by a Return Goods Authorization Number issued by the
Company and must be returned freight prepaid. Any product received without
a Return Goods Authorization Number from the Company will be refused.
Cooper Lighting is not responsible for merchandise damaged in transit.
Repaired or replaced products shall be subject to the terms of this warranty
and are inspected when packed. Evident or concealed damage that is made
in transit should be reported at once to the carrier making the delivery and a
claim filed with them.
Customer First Center • 1121 Highway 74 South, Peachtree City, GA 30269 USA
© 2003 Cooper Lighting
Reproductions of this document without prior written approval of Cooper Lighting are strictly prohibited.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
|