Use & Care Guide
Model No.
153.332620 40 Gallon Tall
153.332640 50 Gallon Tall
Kenmore Elite
®
Gas Water Heater
For potable water heating only.
Not suitable for space heating.
Not for use in mobile homes.
INSTALLER: Affix these instructions to or near
the water heater.
OWNER: Retain these instructions for future
reference.
FOR YOUR SAFETY: An odorant is added to
the gas used by this water heater.
ADVERTENCIA
Si no puede leer o entender el inglés y necesita el manual de
instrucciones en español, puede solicitarlo al 1-800-821-2017. NO
TRATE DE INSTALAR U OPERAR ESTE CALENTADOR DE AGUA
SI NO ENTIENDE LAS INSTRUCCIONES. No hacer caso de esta
advertencia podría originar lesiones graves o mortales.
P/N 317997-000 (0810)
Sears Brands Management Corporation,
Hoffman Estates, IL 60179 U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Breathing Hazard - Carbon Monoxide Gas
Install vent system in accordance with
codes.
Do not operate water heater if flood
damaged
Fire or Explosion Hazard
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Heater should not be installed for High
Altitude operation above 10,100 feet
(3,078 m).
Avoid all ignition sources if you smell Natural or LP gas.
Do not expose water heater control to excessive gas
pressure.
Do not operate if soot buildup.
Use only gas shown on rating plate.
Do not obstruct water heater air intake
with insulating jacket.
Maintain required clearances to combustibles.
Keep ignition sources away from faucets after extended
period of non-use.
Do not place chemical vapor emitting
products near water heater.
Gas and carbon monoxide detectors
are available.
Read instruction manual before
installing, using or servicing
water heater.
Breathing carbon monoxide can cause brain damage or death.
Always read and understand instruction manual.
Improper installation and use may result
in property damage.
Do not operate water heater if flood damaged.
Install in location with drainage.
Fill tank with water before operation.
Be alert for thermal expansion.
Refer to instruction manual for installation and service.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SAFE INSTALLATION, USE AND SERVICE................................................................................................. 2
Important Definitions................................................................................................................................................. 2
SAFETY PRECAUTIONS ........................................................................................................................... 2-3
Table of Contents................................................................................................................................................... 4-5
PRODUCT WARRANTY ................................................................................................................................ 6
CUSTOMER RESPONSIBILITIES................................................................................................................. 7
PRODUCT SPECIFICATIONS ...................................................................................................................... 8
MATERIALS AND BASIC TOOLS NEEDED.................................................................................................. 9
TYPICAL INSTALLATION ............................................................................................................................ 10
Get to know your Water Heater.............................................................................................................................. 10
IMPORTANT INFORMATION ABOUT THIS WATER HEATER....................................................................11
Installation Checklist ................................................................................................................................................11
INSTALLATION INSTRUCTIONS ........................................................................................................... 12-14
Removing the Old Water Heater............................................................................................................................. 12
Location Requirements........................................................................................................................................... 13
Site Location ........................................................................................................................................................... 13
Clearances and Accessibility .................................................................................................................................. 14
High Altitude Installation ......................................................................................................................................... 14
GAS SUPPLY............................................................................................................................................... 15
Gas Requirements.................................................................................................................................................. 15
Gas Piping .............................................................................................................................................................. 15
Gas Pressure.......................................................................................................................................................... 15
Gas Pressure Testing.............................................................................................................................................. 15
COMBUSTION AIR SUPPLY & VENTILATION ...................................................................................... 17-20
Unconfined Space................................................................................................................................................... 17
Confined Space ...................................................................................................................................................... 17
All Air from Inside the Building................................................................................................................................ 17
All Air from Outdoors............................................................................................................................................... 18
Louvers and Grilles................................................................................................................................................. 18
Vent Pipe System ................................................................................................................................................... 19
Draft Hood Installation ....................................................................................................................................... 19-20
Vent Pipe Size ........................................................................................................................................................ 20
Vent Connectors ..................................................................................................................................................... 20
Chimney Connection............................................................................................................................................... 20
Vertical Exhaust Gas Vent ...................................................................................................................................... 20
WATER SYSTEM PIPING....................................................................................................................... 21-22
Piping Installation.................................................................................................................................................... 21
Closed System/Thermal Expansion........................................................................................................................ 22
Temperature and Pressure Relief Valve................................................................................................................. 22
T&P Relief Valve and Pipe Insulation........................................................................................................................ 23
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL ............................................................................................................................................... 24
Electrical Connections ............................................................................................................................................ 24
Solar Installation ..................................................................................................................................................... 24
Wiring Diagram ....................................................................................................................................................... 24
OPERATING YOUR WATER HEATER...................................................................................................25-30
Lighting Instructions................................................................................................................................................ 25
Water Heater Operation.......................................................................................................................................... 26
Checking the Draft.................................................................................................................................................. 26
Burner Flames ........................................................................................................................................................ 27
Emergency Shut Down........................................................................................................................................... 27
Water Temperature Regulation.......................................................................................................................... 27-28
Powered Anode Rod Operation.............................................................................................................................. 28
SERVICE AND ADJUSTMENT .................................................................................................................... 29
Draining and Flushing............................................................................................................................................. 29
Routine Preventive Maintenance............................................................................................................................ 29
Temperature and Pressure Relief Valve................................................................................................................. 29
MAINTENANCE OF YOUR WATER HEATER........................................................................................ 30-32
Replacement Parts ................................................................................................................................................. 30
Removing the Manifold/Burner Assembly............................................................................................................... 30
Removing the Burner from the Manifold/Burner Assembly .................................................................................... 30
Replacing the Flame Sense/Hot Surface Igniter Assembly.................................................................................... 30
External Inspection & Cleaning of the Air Intake Chamber Screen........................................................................ 31
Cleaning the Combustion Chamber and Air Diverter Assembly............................................................................. 31
Replacing the Manifold/Burner Assembly............................................................................................................... 31
Removing and Replacing the Gas Control Valve/Thermostat................................................................................ 32
TROUBLESHOOTING GUIDE................................................................................................................ 33-35
Start Up Conditions................................................................................................................................................. 33
Operational Conditions ........................................................................................................................................... 34
Service.................................................................................................................................................................... 34
Leakage Checkpoints ............................................................................................................................................. 35
Pressurized Combustion Chamber System Operational Checklist ........................................................................ 36
TROUBLESHOOTING CHART............................................................................................................... 36-37
ELECTRONIC CONTROL DISPLAY TROUBLESHOOTING.................................................................. 38-40
TROUBLESHOOTING FLOWCHART.......................................................................................................... 41
PARTS ORDER LIST................................................................................................................................... 42
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY
12 - YEAR LIMITED WARRANTY ON WATER HEATER
For twelve years from the date of purchase, if this water heater is installed and operated in a single-family home in accordance with the
owner’s manual instructions and all local applicable plumbing codes, Sears will:
1. Supply free water heater parts for those that are defective in material or workmanship.
2. Supply a free water heater for one that develops a leak.
For the second through twelfth year from the purchase date, you must pay the labor cost for installation of parts or water heater.
For commercial, institutional, industrial or residential use by two or more families, the above limited warranty is only for two years. During
the second year you must pay the labor cost for parts or water heater installation.
If governmental regulations prohibit Sears from furnishing a comparable model replacement water heater under this warranty, Sears will
furnish a new water heater of comparable output as permitted by such governmental regulations; however, the Owner will be charged
for the additional cost associated with the changes made to comply with such governmental regulations.
Replacements furnished under this warranty do not carry a new warranty; and are only covered by the unexpired portion of the original
warranty.
1 - YEAR EXCLUSIVE KENMORE LABOR WARRANTY
For the first year from the date of purchase, Sears will, free of charge, supply and install new water heater parts for defective ones or a
new water heater for one that develops a leak.
WARRANTY SERVICE
To obtain warranty service, call 1-800-4-MY-HOME® (1-800-469-4663).
This warranty applies only while this product is in use in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
SEARS BRANDS MANAGEMENT CORPORATION, Hoffman Estates, IL 60179
The price of your water heater does not include a free checkup service call. On water heater installations arranged by Sears, Sears
warrants the installation.
A charge will be made on service calls due to poor or incomplete installation. These include:
a. Adjusting thermostat
b. Condensation
c. Leaks in pipes or fittings
Master Protection Agreements
Congratulations on making
a
smart purchase. Your new
•
$250 Food Loss Protection annually for any food spoilage
that is the result of mechanical failure of any covered
refrigerator or freezer.
Kenmore® product is designed and manufactured for years
of dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That’s when
having a Master Protection Agreement can save you money and
aggravation.
•
•
Rental reimbursement if repair of your covered product takes
longer than promised.
10% discount off the regular price of any non-covered repair
service and related installed parts.
The Master Protection Agreement also helps extend the life of your
new product. Here’s what the Agreement* includes:
Once you purchase the Agreement, a simple phone call is all that it
takes for you to schedule service. You can call anytime day or night,
or schedule a service appointment online.
•
Parts and labor needed to help keep products operating
properly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no
functional failure excluded from coverage— real protection.
The Master Protection Agreement is a risk free purchase. If you
cancel for any reason during the product warranty period, we
will provide a full refund. Or, a prorated refund anytime after the
product warranty period expires. Purchase your Master Protection
Agreement today!
•
Expert service by a force of more than 10,000 authorized
Sears service technicians, which means someone you can
trust will be working on your product.
•
•
Unlimited service calls and nationwide service, as often as
you want us, whenever you want us.
Somelimitationsandexclusionsapply. Forpricesandadditional
information in the U.S.A. call 1-800-827-6655.
“No-lemon” guarantee – replacement of your covered product
if four or more product failures occur within twelve months.
* Coverage in Canada varies on some items. For full details,
call Sears Canada at 1-800-361-6665.
•
•
Product replacement if your covered product can’t be fixed.
Annual Preventive Maintenance Check at your request – no
Sears Installation Service
extra charge.
For Sears professional installation of home appliances, garage door
openers, water heaters, and other major home items, in the U.S.A.
or Canada call 1-800-4-MY-HOME®.
•
•
Fast help by phone – we call it Rapid Resolution – phone
support from a Sears representative on all products. Think of
us as a “talking owner’s manual.”
Power surge protection against electrical damage due to
power fluctuations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RESPONSIBILITIES
Thank You for purchasing a Kenmore water heater. Properly installed
•
Massachusetts Code requires this water heater to be installed in
accordance with Massachusetts 248-CMR 2.00: State Plumbing
Code and 248-CMR 5.00.
and maintained, it should give you years of trouble free service. If
you should decide that you want the new water heater professionally
®
installed by Sears call 1-800-4-MY-HOME . They will arrange for
prompt, quality installation by Sears authorized contractors.
•
Complies with 40 Ng/J NOx requirements of Texas and most
California AQM Districts.
Abbreviations Found In This Instruction Manual:
•
•
•
•
•
CSA - Canadian Standards Association
WARNING
ANSI - American National Standards Institute
NFPA - National Fire Protection Association
ASME - American Society of Mechanical Engineers
GAMA - Gas Appliance Manufacturers Association
Excessive Weight Hazard
Use two or more people to move and install the water heater.
Failure to do so can result in injury (including back injury).
Important Information About This Water Heater:
IMPORTANT: Do not remove any permanent instructions, labels, or
the data label from either the outside of the water heater or on the
inside of water heater panels.
This gas water heater was manufactured to voluntary safety
standards to reduce the likelihood of a flammable vapor ignition
incident. New technology used in meeting these standards makes this
product more sensitive to installation errors or improper installation
environments. Please review the Installation Checklist section and
make any required installation upgrades or changes.
•
•
•
•
Remove exterior packaging and place installation components
aside.
Inspect all parts for damage prior to installation and
start-up.
This manual contains instructions for the installation, operation,
and maintenance of the gas-fired water heater. It also contains
warnings through out the manual that you must read and be aware
of. All warnings and all instructions are essential to the proper
operation of the water heater and your safety. Since we cannot put
everything on the first few pages, READ THE ENTIRE MANUAL
BEFORE ATTEMPTING TO INSTALL OR OPERATE THE WATER
HEATER.
Completely read all instructions before attempting to assemble
and install this product.
After installation, dispose of/recycle all packaging materials.
•
The installation must conform with these instructions and the
local code authority having jurisdiction. In the absence of local
codes, installations shall comply with the following:
In the United States: The National Fuel Gas CodeANSI Z223.1/
NFPA 54. This publication is available from the Canadian
StandardsAssociation, 8501 East Pleasant Valley Rd, Cleveland
Ohio 44131, or The National Fire Protection Association, 1
Batterymarch Park, Quincy, MA 02269.
•
•
If after reading this manual you have any questions or do not
understand any portion of the instructions, call the Sears Service
Center.
Carefully plan the place where you are going to put the water heater.
Correct combustion, vent action, and vent pipe installation are
very important in preventing death from possible carbon monoxide
poisoning and fires. See Figure 1.
•
•
Examine the location to ensure the water heater complies with
the Installation Instructions section in this manual.
For California installation, this water heater must be braced,
anchored, or strapped to avoid falling or moving during an
earthquake. See instructions for correct installation procedures.
Instructions may be obtained from California’s Office of the
State Architect, 1102 Q Street, Suite 5100, Sacramento, CA
95811. Instructions can also be downloaded to your computer
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS
MODEL
NUMBER
TANK CAPACITY
IN GALS (LTRS)
TYPE
OF
GAS
INPUT
RATE
RECOVERY
RATE GALS.
PER HOUR
@ 90°F RISE
MINIMUM
VENT PIPE
DIA. INCHES
(mm)
DIAMETER
INCHES
(mm)
HEIGHT TO
JACKET TOP
INCHES (mm)
(Btu/hr)
153.332620
153.332640
40 (151)
50 (189)
Natural
Natural
40,000
40,000
42.6
42.6
3 (76) or 4 (102)
3 (76) or 4 (102)
20 (508)
22 (559)
58 (1473)
57.13 (1451)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MATERIALS AND BASIC TOOLS NEEDED
MATERIALS NEEDED
To simplify the installation Sears has available the installation parts shown below. You may or may not need all of these materials,
depending on your type of installation.
METAL DRAIN PANS AVAILABLE
EXPANSION TANKS FOR
THERMAL EXPANSION
CONDITIONS AVAILABLE
IN 2 GALLONS
IN 20” (508 mm) DIAMETER
FOR WATER HEATERS HAVING
A DIAMETER 18” (457 mm) OR
LESS, 24” (610mm) DIAMETER
FOR WATER HEATERS HAVING A
DIAMETER 22” (559 mm) OR LESS
AND AVAILABLE IN 28” (711 mm)
DIAMETER FOR WATER HEATERS
HAVING A DIAMETER 26” (660 mm)
OR LESS.
(7.6 LITERS) AND
5 GALLONS (18.9 LITERS)
CAPACITY THROUGH
LOCAL SEARS STORE
OR SERVICE CENTER.
WATER HEATER INSTALLATION KIT
WITH FLEXIBLE CONNECTORS FOR 3/4”
(19.05 mm) COPPER PLUMBINGAND FLEXIBLE
GAS CONNECTOR WITH FITTINGS.
BASIC TOOLS
ADDITIONAL TOOLS NEEDED
WHEN SWEAT SOLDERING
You may or may not need all these tools, depending on your
type of installation. These tools can be purchased at your local
Sears Store.
• Tubing Cutters or Hacksaw
• Propane Torch
• Soft Solder
• Solder Flux
• Emery Cloth
• Pipe Wrenches (2) 14” (356 mm)
• Screwdriver
• Tin Snips
• 6’ (1.82 m) Tape or Folding Ruler
• Garden Hose
• Wire Brushes
• Drill
• Pipe Dope or Teflon Tape
DRILL
PROPANE
TORCH
TUBING CUTTER
SLOT-HEAD SCREWDRIVER
TIN SNIPS
PHILLIPS SCREWDRIVER
ROLL OF
HACKSAW
EMERY CLOTH
PIPE DOPE
(SQUEEZE TUBE)
USE FOR WATER AND GAS
CONNECTIONS
ROLL OF TEFLON
TAPE (USE ONLY ON
WATER CONNECTIONS)
3/4” (19 mm) WIRE BRUSH
ROLL OF LEAD-FREE
SOFT SOLDER
SOLDER
FLUX
6 FOOT TAPE
GARDEN HOSE
PIPE WRENCH
1/2” (13 mm) WIRE BRUSH
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TYPICAL INSTALLATION
GET TO KNOW YOUR WATER HEATER - GAS MODELS
A
B
C
D
E
F
G
H
I
Vent Pipe
Draft hood
K
L
Outer door
Union
U
V
Main Burner
Flue
Anode (Not Shown)
Hot Water Outlet
Insulation
Gas Supply Piping
Manual Gas Shut-off Valve
Ground Joint Union
Drip Leg (Sediment Trap)
Inner Door
M
N
O
P
Q
R
S
T
Inlet Water Shut-off Valve
Cold Water Inlet
Inlet Dip Tube
Temperature & Pressure Relief Valve
Rating Plate
Flue Baffle
Gas Control Valve/Thermostat
Drain Valve
W Suitable Metal Drain Pan
X
Y
Control Display
Power Supply Transformer
(Shown detached from Heater)
YY Pressure Switch
(Shown detached from Heater)
Air Intake Chamber
Z
ZZ FV Sensor (Shown without Bracket)
J
*
*
INSTALL IN ACCORDANCE
WITH LOCAL CODES.
DRIP LEG AS REQUIRED
BY LOCAL CODES.
(S) GAS CONTROL VALVE/THERMOSTAT
*
ALL PIPING MATERIALS
TO BE SUPPLIED BY
CUSTOMERS.
TO VENT TERMINATION
ON ROOF
INSTALL THERMAL EXPANSION
TANK IF WATER HEATER IS
INSTALLED IN A CLOSED
WATER SYSTEM
A
IMPORTANT:
WHEN BRUSHING ON AN
APPROVED NONCORROSIVE
LEAK DETECTION SOLUTION,
DO NOT SPLASH SOLUTION
ONTO ELECTRICAL CON-
NECTIONS (SEE PAGE 27).
L
M
N
B
D
PRESSURE
SWITCH/FAN,
FV SENSOR
MANIFOLD TUBE
CONNECTOR
POWER SUPPLY
TRANSFORMER
CONNECTOR
IGNITER/
FLAME
SENSE
CONNECTOR
VACUUM RELIEF
O
VALVE
*INSTALL PER
LOCAL CODES
DISPLAY, ANODE
ROD CONNECTOR
P
E
R
(U) NATURAL GAS BURNER ASSEMBLY
X
MANIFOLD DOOR GASKET
MANIFOLD DOOR ASSEMBLY
MANIFOLD COMPONENT
BLOCK W/ RETAINER CLIP
Q
Z
BURNER
IGNITER / FLAME SENSE
CONNECTOR WIRE
FLAME SENSE
F
G
DISCHARGE PIPE
(DO NOT CAP OR PLUG.)
MANIFOLD
TUBE
S
H
HOT SURFACE
IGNITER
IGNITER / FLAME SENSE
CONNECTOR WIRE
V
T
U
MANIFOLD DOOR ASSEMBLY
I
6” MAXIMUM
AIR GAP
BURNER
MANIFOLD TUBE
FLOOR DRAIN
YY
W
J
ZZ
VIEW PORT
Y
K
IMPORTANT: DO NOT USE AN EXTENSION CORD TO CONNECT
THE WATER HEATER TO AN ELECTRICAL OUTLET.
FIGURE 1.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION ABOUT THIS WATER HEATER
This gas water heater was manufactured to voluntary safety standards to reduce the likelihood of a flammable vapor ignition incident.
The new technology used in meeting these standards makes this product more sensitive to installation errors. Please review the following
checklist and make any required installation upgrades or changes.
.
Questions? Contact Sears at (1-800-469-4663)
Installation Checklist
Water Heater Location
Vent Pipe System
Check for proper drafting at the water heater draft hood. Refer
to the “Checking the Draft” section of this manual for the test
procedure. If the procedure shows insufficient draft is present,
please check the following.
Water heater location is important and can affect system
performance. Please check the following:
□
□
Installation area free of corrosive elements and flammable
materials.
□
□
Draft hood properly installed.
Centrally located with the water piping system (For new
installations). Located as close to the gas piping, vent pipe
system and 120VAC outlet as possible.
Vent connectors securely fastened with screws and
supported properly to maintain six inch clearance.
□
□
Vent connector made of approved material and sized
correctly.
□
□
□
□
Located indoors and in a vertical position. Protected from
freezing temperatures.
Vent pipe system installed according to all local and state
codes or, in the absence of local and state codes, the
“National Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current
edition.
Proper clearances from combustible surfaces
maintained and not installed directly on a carpeted floor.
Provisions made to protect the area from water damage.
Metal drain pan installed and piped to an adequate drain.
□
□
Flue baffle properly positioned in the flue tube.
Sufficient room to service the water heater. See Clearances
and Accessibility section of this manual.
Check the vent system for restrictions/obstructions and
check the vent termination height. Refer to the “Combustion
Air and Ventilation” section of this water heater manual for
specific requirements.
□
□
Water heater not located near an air moving device.
Is the installed environment dirty (excessive amounts of lint,
dirt, dust, etc.)? If so, the air intake chamber louvers located
on the side of the water heater will need to be cleaned
periodically. Refer to the maintenance section of your water
heater’s manual for information on cleaning the “Air Intake
Chamber Screen”.
□
Recheck for sufficient combustion air supply.
Water System Piping
□
Temperature and pressure relief valve properly installed with
a discharge line run to an open drain and protected from
freezing.
Combustion Air Supply and Ventilation
□
□
□
□
All piping properly installed and free of leaks.
Heater completely filled with water.
Check for sufficient combustion air supply. Insufficient air for the
combustion of gas will result in a inferior burner flame “yellow-
lazy”, thereby allowing smoking and carbon formation (sooting) to
build up in the combustion chamber.
Closed system pressure build-up devices installed.
Mixing valve (when applicable) installed per manufacturer’s
instructions (See Water Temperature Regulation section).
Is the water heater installed in a closet or other small, enclosed
space? If so:
Gas Supply and Piping
□
Gas type is the same as that listed on the water heater rating
plate.
□
□
Are there openings for make-up air to enter and exit the
room/area?
□
□
Gas line equipped with shut-off valve, union, and drip leg.
Are the openings of sufficient size? Remember, if there are
other gas-fired or air-consuming appliances in the same
room, you need more make-up air. Refer to the Location
Requirements section of this water heater manual for
specific requirements.
Use pipe joint compound or teflon tape marked as being
resistant to the action of petroleum gases.
□
□
Adequate pipe size and approved pipe material.
An approved noncorrosive leak detection solution used
to check all connections and fittings for possible gas leaks.
Correct any leak found.
Fresh air not taken from areas that contain negative pressure
producing devices such as exhaust fans, dryers, fireplaces, etc.
□
Is there a furnace/air handler in the same room space as
the water heater? If so, has a return air duct system been
attached that exits the room? If so, check for leaks on the
air duct system. If no air duct system is present, correct
immediately by contacting a local Heating, Ventilation, Air-
Conditioning & Refrigeration (HVAC-R) authorized service
provider.
Electrical Supply
□
□
Water heater to be located as close as possible to a 120VAC
outlet (extension cord is not allowed).
Electrical supply installed according to all local and state
codes or, in the absence of local and state codes, the
“National Electrical Code”, ANSI/NFPS 70 current edition.
□
□
Fresh air supply free of corrosive elements and
flammable vapors.
Ductwork is the same cross-sectional area as the
openings.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Removing the Old Water Heater
4.
Attach a hose to the water heater
drain valve and put the other end
in a floor drain or outdoors. (See
Figures 2 and 5.) Open the water
heater drain valve.
5
2
6
1
MANUAL GAS
SHUT-OFF VALVE
GROUND
JOINT
UNION
DISCHARGE PIPE
(DO NOT CAP
OR PLUG)
CHECK WITH
LOCAL UTILITY
FIGURE 5.
FOR MINIMUM HEIGHT
3
5.
6.
Disconnect the vent pipe from the draft hood where it connects
to the water heater. In most installations the vent pipe can
be lifted off after any screw or other attached devices are
removed. Dispose of the draft hood. The new water heater
has a draft hood which must be used for proper operation.
4
3” MINIMUM
DRIP LEG
6” MAXIMUM
AIR GAP
SUITABLE
DRAIN
If you have copper piping to the water heater, the two copper
water pipes can be cut with a hacksaw approximately four
inches away from where they connect to the water heater.
See Figure 6. This will avoid cutting off pipes too short.
Additional cuts can be made later if necessary. Disconnect the
temperature-pressure relief valve drain line. When the water
heater is drained, disconnect the hose from the drain valve.
Close the drain valve. The water heater is now completely
disconnected and ready to be removed.
FIGURE 2.
1.
Turn “OFF” the gas supply to
the water heater.
If the main gas line shutoff valve
serving all gas appliances is used,
also shut “OFF” the gas at each
appliance. Leave all gas appliances
shut “OFF” until the water heater
installation is completed. See
Figures 2 and 3.
FIGURE 3.
2.
Open a nearby hot water faucet
until the water is no longer hot.
When the water has cooled,
turn “OFF” the water supply to
the water heater at the water
shut off valve or water meter.
Some installations require that
the water be turned off to the
entire house. See Figures 2
and 4.
FIGURE 6.
If you have galvanized pipes to the water heater, loosen
the two galvanized pipes with a pipe wrench at the union in
each line. Also disconnect the piping remaining to the water
heater. See Figure 7. These pieces should be saved since
they may be needed when reconnecting the new water heater.
Disconnect the temperature-pressure relief valve drain line.
When the water heater is drained, disconnect the hose from
the drain valve. Close the drain valve. The water heater
is now completely disconnected and ready to be removed.
Mineral buildup or sediment may have accumulated in the
old water heater. This causes the water heater to be much
heavier than normal and this residue, if spilled out, could
cause staining.
FIGURE 4.
3.
Check again to make sure the gas supply is “OFF” to the water
heater. Then disconnect the gas supply connection from the
gas control valve.
FIGURE 7.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
If flammable liquids or vapors have spilled or leaked in the area
of the water heater, leave the area immediately and call the fire
department from a neighbor’s home. Do not attempt to clean the
spill until all ignition sources have been extinguished.
Location Requirements
WARNING
Carbon Monoxide Poisoning Hazard
Do not install in a mobile home.
WARNING
Fire or Explosion Hazard
Doing so can result in carbon monoxide poisoning and death.
• Read instruction manual before installing, using or
servicing water heater.
The FVIR System is designed to reduce the risk of flammable
vapor-related fires. Flammable liquids (such as gasoline,
solvents, propane, etc,) emit flammable vapors which can be
ignited by a gas water heater’s hot surface igniter or main burner.
The resulting flashback and fire can cause death or serious burns
to anyone in the area.
• Improper use may result in fire or explosion.
• Maintain required clearances to combustibles.
Keep combustibles such as boxes, magazines, clothes, etc. away
from the water heater area.
FIGURE 8.
Site Location
FV Sensor
•
Select a location near the center of the water piping system.
The water heater must be installed indoors and in a vertical
position on a level surface. DO NOT install in bathrooms,
bedrooms, or any occupied room normally kept closed.
This heater is equipped with a FV sensor for detecting the
presence of flammable vapors. When the sensor detects those
vapors, the unit will shut down and not operate. Should this
happen, please refer to the troubleshooting guide on pages 38-40
(numbers 9,11,12). Even though this water heater is a flammable
vapors ignition resistant water heater and is designed to reduce
the chances of flammable vapors being ignited, gasoline and
other flammable substances should never be stored or used in
the same vicinity or area containing a gas water heater or other
open flame or spark producing appliance.
•
Locate the water heater as close to the chimney or gas vent
as practical. Consider the vent system piping and combus-
tion air supply requirements when selecting the water heater
location. The venting system must be able to run from the
water heater to termination with minimal length and elbows.
•
•
Locate the water heater near the existing gas piping. If
installing a new gas line, locate the water heater to minimize
the pipe length and elbows.
The water heater should be located in an area not subject
to freezing temperatures. Water heaters located in
unconditioned spaces (i.e., attics, basements, etc.) may
require insulation of the water piping and drain piping to
protect against freezing. The drain and controls must be
easily accessible for operation and service. Maintain proper
clearances as specified on the water heater.
WARNING
•
•
Do not locate the water heater near an air-moving device.
The operation of air-moving devices such as exhaust fans,
ventilation systems, clothes dryers, fireplaces, etc., can af-
fect the proper operation of the water heater. Special atten-
tion must be given to conditions these devices may create.
Flow reversal of flue gases may cause an increase of carbon
monoxide inside of the dwelling (Figure 10).
FLAMMABLES
Flammable Vapors
FIRE AND EXPLOSION HAZARD
Can result in serious injury or death
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance. Storage of or use of gasoline or other
flammable vapors or liquids in the vicinity of this or
any other appliance can result in serious injury or
death.
The water heater is to be located as close as possible to
a 120VAC outlet. NOTE: all electrical wiring should be in
accordance to the NEC and all local/state electrical codes
(extension cord is not allowed).
Read and follow water heater warnings and
instructions
NOTE: This water heater must be installed according to all local and
state codes or, in the absence of local and state codes, the “National
Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition and the
“National Electrical Code”, ANSI/NFPS 70 current edition.
Do not use or store flammable products such as gasoline,
solvents, or adhesives in the same room or area near the
water heater. If such flammables must be used, all gas burning
appliances in the vicinity must be shut off and their pilot lights
extinguished. Open the doors and windows for ventilation while
flammable substances are in use.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EXHAUST FAN
IMPORTANT: The water heater should be located in an area where
leakage of the tank or connections will not result in damage to the
area adjacent to the water heater or to lower floors of the structure.
Due to the normal corrosive action of water, the tank will eventually
leak after an extended period of time. Also any external plumbing
leak, including those from improper installation, may cause early
failure of the tank due to corrosion if not repaired. If the homeowner
is uncomfortable with making the repair a qualified technician should
be contacted. A suitable metal drain pan should be installed under
the water heater as shown below, to help protect the property from
damage which may occur from condensate formation or leaks in
the piping connections or tank. The pan must limit the water level
to a maximum depth of 1-3/4” and be two inches wider than the
heater and piped to an adequate drain. Locate the water heater
near a suitable indoor drain. Outside drains are subject to freezing
temperatures which can obstruct the drain line. The piping should be
at least 3/4” ID and pitched for proper drainage.
REVERSE FLOW
OF GASES
FIGURE 10.
Clearances and Accessibility
NOTE: Minimum clearances from combustible materials are
stated on the label on the front of the heater adjacent to the gas
control valve/thermostat of the water heater.
The water heater is certified for installation on a combustible
floor.
•
IMPORTANT: If installing over carpeting, the carpeting must
be protected by a metal or wood panel beneath the water
heater. The protective panel must extend beyond the full
width and depth of the water heater by at least five inches
(127mm) in any direction; or if in an alcove or closet installa-
tion, the entire floor must be covered by the panel.
•
Figure 11 may be used as a reference guide to locate the
specific clearance locations. A minimum of 5 inches of front
clearance should be provided for inspection and service.
FIGURE 9.
Pipe to an
adequate drain
6” min. at
Single Wall
Vent Pipe
1-3/4”
max.
12” min.
Top to
Ceiling
At least 2” greater
than the water heater.
0” min.
Back
Water heater life depends upon water quality, water usage, water
temperature and the environment in which the water heater is
installed. Water heaters are sometimes installed in locations
where leakage may result in property damage, even with the use
of a metal drain pan piped to a drain. However, unanticipated
damage can be reduced or prevented by a leak detector or water
shut-off device used in conjunction with a piped metal drain
pan. These devices are available from some plumbing supply
wholesalers and retailers, and detect and react to leakage in
various ways:
0” min.
Sides
0” min.
Air Inlet
Chamber
5” min.
Front
Top View
•
•
•
•
Sensors mounted in the metal drain pan that trigger an alarm
or turn off the incoming water to the water heater when water
is detected.
Minimum Clearance Locations
FIGURE 11.
Sensors mounted in the metal drain pan that turn off the
water supply to the entire home when water is detected in
the metal drain pan.
Water supply shut-off devices that activate based on the
water pressure differential between the cold water and hot
water pipes connected to the water heater.
High Altitude Installation
This water heater should not be installed for operation at
elevations above 10,100 ft. (3,078 m).
Devices that will turn off the gas supply to a gas water heater
while at the same time shutting off its water supply.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS SUPPLY
WARNING
Manual Gas
Shut-Off Valve
Ground Joint Union
Install a readily acces-
sible manual shut-off
valve in the gas supply
line as recommended
by the local utility.
Discharge Pipe
(Do Not plug or cap)
Explosion Hazard
Use a new CSA approved gas supply line.
Install a shut-off valve.
Check with local utility
for minimum height.
•
•
•
3” Minimum
Drip Leg
6” Max. Air Gap
Suitable Drain
Do not connect a natural gas water heater to an L.P. gas
supply.
FIGURE 12.
•
•
Do not connect an L.P. gas water heater to a natural gas
supply.
Gas Pressure
Failure to follow these instructions can result in death,
explosion, or carbon monoxide poisoning.
WARNING
Gas Requirements
IMPORTANT: Read the rating plate to be sure the water heater
is made for the type of gas you will be using in your home. This
information will be found on the rating plate located near the gas
control valve/thermostat. If the information does not agree with
the type of gas available, do not install or light. Call your dealer.
Explosion Hazard
•
•
Gas leaks can not always be detected by smell.
NOTE: An odorant is added by the gas supplier to the gas used
by this water heater. This odorant may fade over an extended
period of time. Do not depend upon this odorant as an indication
of leaking gas.
Gas suppliers recommend that you use a gas
detector approved by UL or CSA.
•
•
For more information, contact your gas supplier.
Gas Piping
If a gas leak is detected, follow the “What to do if you
smell gas” instructions on the cover of this manual.
The gas piping must be installed according to all local and state
codes or, in the absence of local and state codes, the “National
Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition.
Tables 1 and 2 on the following page provide a sizing reference for
commonly used gas pipe materials. Consult the “National Fuel Gas
Code” for the recommended gas pipe size of other materials.
IMPORTANT: The gas supply pressure must not exceed the maximum
supply pressure as stated on the water heater’s rating plate. The
minimum supply pressure is for the purpose of input adjustment.
NOTE: Use pipe joint compound or teflon tape marked as being
resistant to the action of petroleum gases (See Figure 12.)
Gas Pressure Testing
IMPORTANT: This water heater and its gas connection must be leak
tested before placing the appliance in operation.
1. Install a readily accessible manual shut-off valve in the gas
supply line as recommended by the local utility. Know the
location of this valve and how to turn off the gas to this unit.
2. Install a drip leg (if not already incorporated as part of
the water heater) as shown. The drip leg must be no less
than three inches long for the accumulation of dirt, foreign
material, and water droplets.
3. Install a ground joint union between the gas control valve/
thermostat and the manual shut-off valve. This is to allow
easy removal of the gas control valve/ thermostat.
4. Turn the gas supply on and check for leaks. Test all
connections by brushing on an approved noncorrosive leak-
detection solution. Bubbles will show a leak. Correct any
leak found.
•
If the code requires the gas lines to be tested at a pressure
exceeding 14” W.C., the water heater and its manual shut-off
valve must be disconnected from the gas supply piping system
and the line capped.
•
If the gas lines are to be tested at a pressure less than 14” W.C.,
the water heater must be isolated from the gas supply piping
system by closing its manual shut-off valve.
NOTE: Air may be present in the gas lines and could prevent the
burner from lighting on initial start-up. The gas lines should be purged
of air by a qualified technician after installation of the gas piping
system. While purging the gas piping system of air, insure that the
fuel is not spilled in the area of the water heater installation, or
any source of ignition (NOTE: spilled fuel may trip the FV Sensor
preventing heater from starting). If the fuel is spilled while
purging the piping system of air follow the “WHAT TO DO IF YOU
SMELL GAS” instructions on the cover of this manual.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Pipe Capacity Table
WARNING
WARNING
Explosion Hazard
Use a new CSA approved gas supply line.
Install a shut-off valve.
Explosion Hazard
•
•
Gas leaks can not always be detected by smell.
•
•
•
Gas suppliers recommend that you use a gas
detector approved by UL or CSA.
Do not connect a natural gas water heater to an L.P. gas
supply.
•
•
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you
smell gas” instructions on the cover of this manual.
•
•
Do not connect an L.P. gas water heater to a natural gas
supply.
Failure to follow these instructions can result in death,
explosion, or carbon monoxide poisoning.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
COMBUSTION AIR & VENTILATION
TABLE 3
Minimum
Square
Feet with
8’ Ceiling
WARNING
Typical Room
with 8’ Ceiling
BTUH Input
Carbon Monoxide Warning
Water heater must be vented to outdoors.
30,000
45,000
60,000
75,000
90,000
105,000
120,000
135,000
188
281
375
469
563
657
750
844
9 x 21
14 x 20
15 x 25
15 x 31
20 x 28
20 x 33
25 x 30
28 x 30
Vent must be installed by a qualified technician using
the installation instructions.
Examples of a qualified technican include: gas
technicians, authorized gas company personel, and
authorized service persons.
Failure to so do can result in death or carbon monoxide
poisoning.
IMPORTANT: Air for combustion and ventilation must not
come from a corrosive atmosphere. Any failure due to corrosive
elements in the atmosphere is excluded from warranty coverage.
IMPORTANT:
•
•
•
The area must be open and be able to provide the proper air
requirements to the water heater. Areas that are being used
for storage or contain large objects may not be suitable for
water heater installation.
The following types of installation (not limited to the following)
will require outdoor air for combustion due to chemical exposure
and may reduce but not eliminate the presence of corrosive
chemicals in the air:
Water heaters installed in open spaces in buildings with un-
usually tight construction may still require outdoor air to func-
tion properly. In this situation, outside air openings should be
sized the same as for a confined space.
•
•
•
•
•
beauty shops
photo processing labs
buildings with indoor pools
water heaters installed in laundry, hobby, or craft rooms
water heaters installed near chemical storage areas
Modern home construction usually requires supplying out-
side air into the water heater area.
Combustion air must be free of acid-forming chemicals such as
sulfur, fluorine, and chlorine. These elements are found in aerosol
sprays, detergents, bleaches, cleaning solvents, air fresheners, paint,
and varnish removers, refrigerants, and many other commercial and
household products. When burned, vapors from these products form
highly corrosive acid compounds. These products should not be
stored or used near the water heater or air inlet.
Confined Space
For the correct and proper operation of this water heater, ample
air must be supplied for the combustion, ventilation, and dilution
of flue gases. Small enclosures and confined areas must have
two permanent openings so that sufficient fresh air can be drawn
from outside of the enclosure. One opening shall be within 12
inches of the top and one within 12 inches of the bottom of the
enclosure as shown in Figure 13.
Combustion and ventilation air requirements are determined by
the location of the water heater. The water heater may be located
in either an open (unconfined) area or in a confined area or small
enclosure such as a closet or small room. Confined spaces are
areas with less than 50 cubic feet for each 1,000 BTUH of the total
input for all gas-using appliances.
The size of each opening (free area) is determined by the total
BTUH input of all gas utilization equipment (i.e., water heaters,
furnaces, clothes dryers, etc.) and the method by which the air
is provided. The BTUH input can be found on the water heater
rating plate. Additional air can be provided by two methods:
Unconfined Space
A water heater in an unconfined space uses indoor air for
combustion and requires at least 50 cubic feet for each 1,000
BTUH of the total input for all gas appliances. The table below
shows a few examples of the minimum square footage (area)
required for various BTUH inputs.
1. All air from inside the building.
2. All air from outdoors.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
free area of the opening to which they connect. The minimum
dimension of rectangular air ducts cannot be less than three
inches.
12” Max.
The size of each of the two openings is determined by the
method in which the air is to be provided. Refer to Table 4 to
calculate the minimum free area for each opening. Figures 15,
16, 17 and 18 are typical examples of each method.
Permanent
openings to
the outside or
additional
rooms within
the building
Closet
or other
confined
space
Louvers and Grilles
In calculating free area for ventilation and combustion air supply
openings, consideration must be given to the blocking effect
of protection louvers, grilles, and screens. These devices can
reduce airflow, which in turn may require larger openings to
achieve the required minimum free area. Screens must not be
smaller than 1/4” mesh. If the free area through a particular
design of louver or grille is known, it should be used in calculating
the specified free area of the opening. If the design and free area
are not known, it can be assumed that most wood louvers will
allow 20 - 25% of free area while metal louvers and grilles will
allow 60 - 75% of free area.
12” Max.
FIGURE 13.
All Air from the Building
When additional air is to be provided to the confined area
from additional room(s) within the building, the total volume of
the room(s) must be of sufficient size to properly provide the
necessary amount of fresh air to the water heater and other
gas utilization equipment in the area. If you are unsure that the
structure meets this requirement, contact your local gas utility
company or other qualified agency for a safety inspection.
Each of the two openings shall have a minimum free area of 1
square inch per 1,000 BTUH of the total input rating of all gas
utilization equipment in the confined area, but not less than 100
square inches (Figure 14).
Louvers and grilles must be locked open or interconnected with
the equipment so that they are opened automatically during
equipment operation.
Keep louvers and grilles clean and free of debris or other
obstructions.
TABLE 4
Minimum Free Area of Permanent Openings for Ventilation and
Combustion Air Supply - All Air from Outdoors Only.
Based on total BTUH input rating for all utilizing equipment
within the confined space.
Confined
Space
Minimum Free Area
Per Opening (sq. in.) Reference Drawing
Opening Source
*Direct to outdoors
Vertical Ducts
1 sq. in, per 4000 BTUH
1 sq. in, per 4000 BTUH
1 sq. in, per 2000 BTUH
1 sq. in, per 3000 BTUH
Figure 15
Figure 16
Figure 17
Figure 18
Permanent
Openings
Horizontal Ducts
Single Opening
Example: A water heater with an input rating of 50,000 BTUH using
horizontal ducts would require each opening to have a minimum free
area of 25 square inches.
1 Square
inch/1000
BTUH
(min. 100
sq. in.)
Minimum free area = 50,000 BTUH x 1 sq. in. / 2000 BTUH = 25 sq. in.
These openings connect directly with the outdoors through a venti-
lated attic, a ventilated crawl space, or through an outside wall.
*
Consult the local codes of your area for specific ventilation and
combustion air requirements.
FIGURE 14.
All Air from Outdoors
Outdoor fresh air can be provided to a confined area either
directly or by the use of vertical and horizontal ducts. The fresh
air can be taken from the outdoors or from crawl or attic spaces
that freely communicate with the outdoors. Attic or crawl spaces
cannot be closed and must be properly ventilated to the outside.
Ductwork must be of the same cross-sectional area as the
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Gable Vent
to Outdoors
Alternative
Opening
Location
Install Above
Insulation
Confined
Space
1 sq. in. per
3000 BTUH
Confined
Space
Outlet Air
to the Attic
1 sq. in. per
4000 BTUH
Inlet Air
from the
Crawl Space
Alternative
Air Inlet
All Air From Outdoors - Using A Single Permanent Opening
FIGURE 18.
Open
1 sq. in. per
4000 BTUH
Foundation
Vent
Vent Pipe System
All Air From Outdoors: Inlet Air From Ventilated
Crawl Space/Outlet Air To Ventilated Attic
This water heater uses a non-direct, single-pipe vent system to
remove exhaust gases created by the burning of fossil fuels. Air
for combustion is taken from the immediate water heater location
or is ducted in from the outside (see “Combustion Air Supply and
Ventilation”).
FIGURE 15.
Gable Vent
to Outdoors
Install Above
Insulation
This water heater must be properly vented for the removal of
exhaust gases to the outside atmosphere. Correct installation of
the vent pipe system is mandatory for the proper and efficient
operation of this water heater and is an important factor in the life
of the unit.
Outlet Air
Confined
Space
to the Attic
1 sq. in. per
4000 BTUH
The vent pipe must be installed according to all local and state
codes or, in the absence of local and state codes, the “National
Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition. The
vent pipe installation must not be obstructed so as to prevent the
removal of exhaust gases to the outside atmosphere.
Inlet Air Duct
1 sq. in. per
4000 BTUH
IMPORTANT: The use of vent dampers is not recommended
by the manufacturer of this water heater. Although some vent
dampers are certified by CSA International, this certification
applies to the vent damper device only and does not mean they
are certified for use on this water heater.
12” Max.
All Air from Outdoors Through Ventilated Attic
FIGURE 16.
U.L. recognized fuel gas and carbon monoxide (CO) detectors
are recommended in all applications and should be installed
using the manufacturer’s instructions and local codes, rules, or
regulations.
1 sq. in. per
2000 BTUH
IMPORTANT: If you lack the necessary skills required to properly
install this venting system, you should not proceed, but get help
from a qualified technician.
Confined
Outlet
Space
Draft Hood Installation
50 GAL. UNIT
40 GAL. UNIT
Outdoor
Air Ducts
Flat Side Of Hood
Next To Water
Connections.
Flat Side Of Hood
Next To Water
Connections.
Installation above
elevation 5,400 ft.
(1,646 m) from sea
level, Reducer Flue
must be installed on
40 gallon unit.
Inlet
Legs
Legs
Draft Hood
Reducer Flue
Legs
Draft Hood
Legs
Screw
Screw
1 sq. in. per
2000 BTUH
Slot
Top
Slot
Top
Slot
Slot
Install The Draft Hood With The Four Screws Provided.
Install The Draft Hood With The Four Screws Provided.
All Air From Outdoors Using Horizontal Ducts
FIGURE 17.
FIGURE 19.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Gal. Water Heater: Align the reducer flue over top of baffle as
shown in Figure 19 (NOTE: reducer flue must be installed on 40
gal. water heater above elevation 5,400 Ft. (1,646 m) from sea
level).
Z223.1(NFPA 54)-current edition.
•
•
•
•
The connector must be installed above the extreme bottom
of the chimney to prevent potentially blocking the flue gases.
The connector must be firmly attached and sealed to prevent
it from falling out.
40 & 50 Gal. Water Heaters: Align the legs of the draft hood with
the slots provided. Insert the legs and secure the draft hood to
the water heater’s top with the four screws provided as shown
in Figure 19. Do not alter the draft hood in any way. If you are
replacing an existing water heater, be sure to use the draft hood
supplied with this water heater.
To aid in removing the connector, a thimble or slip joint may
be used.
The connector must not extend beyond the inner edge of
the chimney as it may restrict the space between it and the
opposite wall of the chimney (Figure 20).
Vent Pipe Size
2 FT. Minimum Above Any Object
3 FT.
Minimum
Within 10 FT. Horizontally
It is important that you follow the guidelines in these instructions
for sizing a vent pipe system. If a transition to a larger vent size
is required, the vent transition connection must be made at the
draft hood outlet.
Support Strap
Seal
Maintain
Clearance*
Do Not Extend
Vent Beyond Edge
Of Chimney
Vent Connectors
1. Type B, Double wall, U.L. Listed Vent Pipe.
2. Single wall Vent Pipe.
Vent
Connector
Slope Up
1/4 Inch
Per Foot
Minimum
Maintain the manufacturer’s specified minimum clearance from
combustible materials when using type B double wall vent pipe.
Vent connectors made of type B, double wall vent pipe material
may pass through walls or partitions constructed of combustible
material if the minimum listed clearance is maintained.
Maintain a six inch minimum clearance from all combustible
materials when using single wall vent pipe.
Chimney Termination Vent System
IMPORTANT: Single wall vent pipe cannot be used for water
heaters located in attics and may not pass through attic spaces,
crawl spaces or any confined or inaccessible location. A single
wall metal vent connector cannot pass through any interior wall.
FIGURE 20.
Do not terminate the vent connector in a chimney that has not
been certified for this purpose. Some local codes may prohibit
the termination of vent connectors in a masonry chimney.
When installing a vent connector, please note the following (See
Figures 20-22):
•
•
•
Install the vent connector avoiding unnecessary bends, which
create resistance to the flow of vent gases.
Vertical Exhaust Gas Vent
Install without dips or sags with an upward slope of at least
1/4-inch per foot.
Vertical exhaust gas vents must be installed with U.L. listed type
B vent pipe according to the vent manufacturer’s instructions and
the terms of its listing.
Joints must be fastened by sheet metal screws or other
approved means. It must be supported to maintain clearances
and prevent separation of joints and damage.
It must be connected to the water heater’s draft hood by a
listed vent connector or by directly originating at the draft hood
opening.
•
•
•
•
The length of the vent connector cannot exceed 75% of the
vertical vent height.
Vertical gas vents must terminate with a listed cap or other roof
assembly and be installed according to their manufacturer’s
instructions.
The vent connector must be accessible for cleaning,
inspection, and replacement.
Vent connectors cannot pass through any ceiling, floor,
firewall, or fire partition.
Gas vents must be supported to prevent damage, joint
separation, and maintain clearances to combustible materials
(Figures 21 and 22).
It is recommended (but not mandatory) that a minimum 12
inches of vertical vent pipe be installed on the draft hood prior
to any elbow in the vent system.
IMPORTANT: This gas vent must be terminated in a vertical
position to facilitate the removal of the burnt gases.
IMPORTANT: Existing vent systems must be inspected for
obstructions, corrosion, and proper installation.
An unused chimney flue or masonry enclosure may be used as a
passageway for the installation of a gas vent (Figure 22).
Common (combined) venting is allowable with vertical type B vent
systems and lined masonry chimneys as long as proper draft for
the water heater is established under all conditions of operation.
CAUTION: DO NOT common vent this water heater with any
power vented appliance.
Chimney Connection
IMPORTANT: Before connecting a vent to a chimney, make sure
the chimney passageway is clear and free of obstructions. The
chimney must be cleaned if previously used for venting solid
fuel appliances or fireplaces. Also consult local and state codes
for proper chimney sizing and application or, in the absence
of local and state codes, the “National Fuel Gas Code”, ANSI
Figures 20-22 are examples of vent pipe system installations and
may or may not be typical for your specific application. Consult
the “National Fuel Gas Code”, NFPA 54, ANSI Z223.1-current
edition and the guidelines set forth by prevailing local codes.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2 FT. Minimum Above
Any Object Within
10 FT. Horizontally
WATER SYSTEM PIPING
Piping Installation
3 FT.
Minimum
Support Strap
Piping, fittings, and valves should be installed according to the
installation drawing (Figure 23). If the indoor installation area
is subject to freezing temperatures, the water piping must be
protected by insulation.
Type B Double
Wall Vent Pipe
Maintain
Clearance*
**Maintain
Specified
Clearance
The water supply pressure should not exceed 80 psi. If this
occurs, a pressure reducing valve with a bypass should be
installed in the cold water inlet line. This should be placed on the
supply to the entire house in order to maintain equal hot and cold
water pressures.
Vent
Connector
Slope Up
1/4 Inch
Per Foot
Minimum
IMPORTANT: Heat cannot be applied to the water fittings on
the heater as they may contain nonmetallic parts. If solder
connections are used, solder the pipe to the adapter before
attaching the adapter to the hot and cold water fittings.
Venting Gas Vent System With Type B Double Wall Vent Pipe.
FIGURE 21.
IMPORTANT: Always use a good grade of joint compound and be
certain that all fittings are drawn up tight.
1. Install the water piping and fittings as shown in Figure 23.
Connect the cold water supply (3/4” NPT) to the cold water
inlet fitting. Connect the hot water piping (3/4” NPT) to the
hot water outlet fitting.
Listed Vent Cap
Maintain Manufacturer’s
Specified Minimum Clearance
IMPORTANT: Some models may contain energy saving heat
traps to prevent the circulation of hot water within the pipes. Do
not remove the inserts within the heat traps.
**Maintain
Specified
Clearance
Support Strap
Seal
Maintain
Clearance*
2. The installation of unions in both the hot and cold water
supply lines is recommended for ease of removing the water
heater for service or replacement.
Vent Connector
Vent
3. The manufacturer of this water heater recommends installing
a mixing valve or an anti-scald device in the domestic hot
water line as shown in Figure 24. These valves reduce the
point-of-use temperature of the water by mixing cold and hot
water and are readily available for use.
Connector
Slope Up
1/4 Inch
Per Foot
Minimum
Unused Chimney
Flue Or Masonry
Enclosure
4. If installing the water heater in a closed water system, install
an expansion tank in the cold water line as specified under
Closed System/Thermal Expansion.
Venting Through Chimney With Type B Double Wall Vent Pipe.
5. Install a shut-off valve in the cold water inlet line. It should be
located close to the water heater and be easily accessible.
Know the location of this valve and how to shut off the water
to the heater.
FIGURE 22.
Maintain vent pipe clearance requirements to local, state and/or the
“National Fuel Gas Code”, ANSI Z223.1(NFPA 54)-current edition.
*
6. A temperature and pressure relief valve must be installed
in the opening marked “Temperature and Pressure (T & P)
Relief Valve” on the water heater. A discharge line must be
added to the opening of the T&P Relief Valve. Follow the
instructions under Temperature and Pressure Relief Valve.
** NFPA 211, Standard for Chimneys, Fireplaces, Vents, and
Solid Fuel-Burning Appliances states that these chimneys are
intended to be installed in accordance with the installation
instructions provided with each chimney support assembly.
Minimum air space clearance to combustible materials should be
maintained as marked on the chimney sections.
7. After piping has been properly connected to the water
heater, remove the aerator at the nearest hot water faucet.
Open the hot water faucet and allow the tank to completely
fill with water. To purge the lines of any excess air, keep
the hot water faucet open for 3 minutes after a constant
flow of water is obtained. Close the faucet and check all
connections for leaks.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
In a closed system use a
thermal expansion tank
Closed System/Thermal Expansion
Cold Water
Inlet Valve
Pressure Reducing
Valve with Bypass
Hot Water
Outlet
Cold Water Supply
to Fixture
Main Water
Supply
Temperature and Pressure (T&P)
Relief Valve (Optional Top T&P
Relief Valve Not Shown)
Massachusetts:
Install a vacuum relief
in cold water line per
section 19 MGL 142
As water is heated, it expands (thermal expansion). In a closed
system, the volume of water will grow. As the volume of water
grows, there will be a corresponding increase in water pressure
due to thermal expansion. Thermal expansion can cause
premature tank failure (leakage). This type of failure is not
covered under the limited warranty. Thermal expansion can also
cause intermittent temperature-pressure relief valve operation:
water discharged from the valve due to excessive pressure build
up. The temperature-pressure relief valve is not intended for the
constant relief of thermal expansion. This condition is not covered
under the limited warranty.
Discharge line
(Do Not Cap or Plug)
1“ Min.
Drain line 3/4”
ID Min.
Metal Drain
Pan 1-3/4”
Depth Max.
6“ Min.
Drain
Typical water piping installation
FIGURE 23.
A properly-sized thermal expansion tank should be installed
on all closed systems to control the harmful effects of thermal
expansion. Contact a plumbing service agency or your retail
supplier regarding the installation of a thermal expansion tank.
Mixed Water
To Fixtures
Unmixed
Hot Water
Temperature and Pressure Relief Valve
Cold Water
Inlet
Explosion Hazard
Hot Water
Outlet
• Temperature-pressure relief
valve must comply with ANSI
Z21.22-CSA 4.4 and ASME
code.
• Properly sized temperature-
pressure relief valve must be
installed in opening provided.
Mixing Valve
(Set To 1200 F)
• Can result in overheating
and excessive tank pressure.
Follow The Mixing Valve
Manufacturer’s Instructions
• Can cause serious injury or
death.
FIGURE 24.
Please note the following:
•
The system should be installed only with piping that is suitable
for potable (drinkable) water such as copper, CPVC, or
polybutylene. This water heater must not be installed using
iron piping or PVC water piping.
Temperature and
Pressure Relief Valve
(T&P)
•
•
Use only pumps, valves, or fittings that are compatible with
potable water.
Discharge line 3/4” Min.
Do not cap or plug.
It is recommend that only full flow ball or gate valves are used
in water piping installations. The use of valves that may cause
excessive restriction to water flow is not recommended.
•
•
•
Use only 95/5 tin-antimony or other equivalent solder. Any
lead based solder must not be used.
Metal Drain Pan
6” Max.
Drain
Piping that has been treated with chromates, boiler seal, or
other chemicals must not be used.
FIGURE 25.
Chemicals that may contaminate the potable water supply
must not be added to the piping system.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
For protection against excessive pressures and temperatures,
a temperature and pressure relief valve must be installed in the
opening marked “T & P RELIEF VALVE” (see Figure 25). This
valve must be design certified by a nationally recognized testing
laboratory that maintains periodic inspection of the production
of listed equipment or materials as meeting the requirements
for Relief Valves for Hot Water Supply Systems, ANSI Z21.22.
The function of the temperature and pressure relief valve is to
discharge water in large quantities in the event of excessive
temperature or pressure developing in the water heater. The
valve’s relief pressure must not exceed the working pressure of
the water heater as stated on the rating plate.
4. Locate the hot water (outlet) & cold water (inlet) pipes to the
water heater.
5. Locate the slit running the length of a section of pipe insulation.
6. Spread the slit open and slip the insulation over the cold
water (inlet) pipe. Apply gentle pressure along the length of
the insulation to ensure it is fully seated around the pipe. Also
ensure that the base of insulation is flush with the water heater.
Once seated, secure the insulation with duct tape, electrical
tape, or equivalent.
7. Repeat steps 5 through 6 for the hot water (outlet) pipe.
8. Add additional sections of pipe insulation as needed.
IMPORTANT: Only a new temperature and pressure relief valve
should be used with your water heater. Do not use an old or
existing valve as it may be damaged or not adequate for the
working pressure of the new water heater. Do not place any valve
between the relief valve and the tank.
Manual Relief Lever
T&P Relief Valve
The Temperature & Pressure Relief Valve:
•
•
•
Must not be in contact with any electrical part.
Must be connected to an adequate discharge line.
Must not be rated higher than the working pressure shown
on the rating plate of the water heater.
T&P Relief Valve
Drain Line
The Discharge Line:
•
•
•
Must not be smaller than the pipe size of the relief valve or
have any reducing coupling installed in the discharge line.
T&P Relief Valve Insulation
Must not be capped, blocked, plugged or contain any valve
between the relief valve and the end of the discharge line.
FIGURE 26.
Must terminate a maximum of six inches above a floor drain
or external to the building. In cold climates, it is recommend-
ed that the discharge pipe be terminated at an adequate
drain inside the building.
•
•
Must be capable of withstanding 250°F (121°C) without dis-
tortion.
Must be installed to allow complete drainage of both the
valve and discharge line.
T&P Relief Valve and Pipe Insulation
1. Locate the temperature and relief valve on the water heater
(also known as a T&P Relief Valve, Figure 26).
2. Locate the slit running the length of the insulation.
3
Spread this slit open and slip it up under the T&P Relief Valve.
See Figure 26. Apply gentle pressure to the insulation to ensure
it is fully seated on the T&P Relief Valve. Once sealed secure
the insulation with a section of duct tape, electrical tape, or
equivalent.
IMPORTANT: The insulation or tape must not block the
discharge opening or hinder access to the manual relief
lever. Ensure a discharge pipe is installed into the T&P valve
discharge opening per the instructions manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
IMPORTANT: Do not use an extension cord to connect the water
heater to an electrical outlet.
Electrical Connections
•
•
The water heater and the outlet are properly grounded.
Before plugging in the water heater, always make sure:
Installed in accordance with prevailing provisions of
local codes, or in the absence of such, National Electric
Code, ANSI/NFPS 70 current edition.
•
•
•
The Voltage and frequency correspond to that specified on
the water heater.
The electrical outlet has the proper overload fuse or breaker
protection.
Completely fill the tank with water and check all connections for
leaks. Open the nearest hot water faucet and let it run for three (3)
minutes to purge the water lines of air and sediment and to ensure
complete filling of the tank. The electrical power may then be
turned on. Verify proper operation after servicing.
Unit is to connect to a 120VAC electrical supply outlet
(extension cord is not allowed).
WARNING
Solar Installation
Electric Shock Hazard
If this water heater is used as a solar storage heater or as a
backup for the solar system, the water supply temperatures to
the water heater tank may be in excess of 120°F. A mixing valve
or other temperature limiting valve must be installed in the water
supply line to limit the supply temperature to 120°F.
Disconnect power before
servicing.
Replace all parts and panels
before operating.
NOTE: Solar water heating systems can often supply water with
temperatures exceeding 180°F and may result in water heater
malfunction.
Failure to do so can result in
death or electrical shock.
Wiring Diagram
FIGURE 27.
Gas Control
Air Intake
Valve / Thermostat
Chamber Fan
Anode
Rod
Pressure
Switch
Control Display
CAUTION:
DO NOT USE AN EXTENSION
CORD TO CONNECT THE
TRANSFORMER TO AN
ELECTRICAL OUTLET.
Igniter/Flame
Sense Connector
FV
Sensor
CAUTION:
Power Supply
Transformer
LABEL ALL WIRES PRIOR TO
DISCONNECTION WHEN SERVICING
CONTROLS. WIRING ERRORS CAN CAUSE
IMPROPER AND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING YOUR WATER HEATER
Operating Instructions
Read and understand these directions thoroughly before
attempting to operate the water heater. Make sure the view port
is not missing or damaged (See Figure 36). Make sure the tank
is completely filled with water before operating the water heater.
The gas control valve/thermostat has a “On/Off Switch” and
needs to be turned on before water heater is operational. Check
the label on the front of heater near the gas control valve/
thermostat for the correct gas. Do not use this water heater with
any gas other than the one listed on the label. If you have any
questions or doubts, consult your gas supplier or gas utility
company.
WARNING
Explosion Hazard
Replace view port if glass is missing
or damaged.
Failure to do so can result in death,
explosion or fire.
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury
or loss of life.
FLAMMABLE
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.
This appliance does not have a pilot. It is equipped with
an ignition device that will automatically light the
burner. Do not try to light the burner by hand.
BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electric switch;
do not use any phone in your building.
A.
If you cannot reach your gas supplier, call the
fire department.
Use only your hand to push in the electronic display
buttons and gas control switch. Never use tools.
If the control buttons will not push in, don't try to
repair them, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
C.
D.
B.
Do not use this appliance if any part has been
under water. Immediately contact a qualified
installer or service agency to replace a flooded
water heater. Do not attempt to repair the unit.
It must be replaced!
Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
OPERATING INSTRUCTIONS
ON
OFF
FIGURE 28.
ON/OFF
SWITCH
"GAS CONTROL"
"ELECTRONIC DISPLAY"
1.
STOP! Read the safety information
above on the label.
8. Set the ON/OFF switch on the gas control to the
"ON" postition.
2.
3.
Turn on all electrical power to the appliance.
Set the ON/OFF switch on the gas control to the
"ON" position.
Set the Electronic Display to the desired setting by first
9.
Set the Electronic Display to the lowest
4.
pressing the COOLER
and HOTTER
but-
setting by first pressing the COOLER
and
HOTTER
buttons together and holding for 1
tons together and holding for 1 second. Then press
second. Then press the COOLER
the lowest setting.
button to
the HOTTER
is reached.
button until the desired setting
5.
6.
Set the ON/OFF switch on the gas control to the
"OFF" position.
This appliance is equipped with a device
which automatically lights the burner.
DANGER: Hotter water increases the
risk scald injury. Consult the instruction
manual before changing temperature.
If the appliance will not operate, follow the instruc-
tions "TO TURN OFF GAS TO APPLIANCE" and
call your technician or gas supplier.
10.
DO NOT TRY TO LIGHT THE BURNER BY HAND.
Wait five (5) minutes to
If you then smell gas,
clear out any gas.
STOP! Follow "B" in
7.
WARNING: TURN OFF ALL
the safety information above on this label. If you
don't smell gas, go to the next step.
ELECTRIC POWER BEFORE SERVICING.
TO TURN OFF GAS TO APPLIANCE
Set the Electronic Display to the lowest setting by first
1.
2. Set the ON/OFF switch on the gas control to the
"OFF" postition.
pressing the COOLER
tons together and holding for 1 second. Then press
the COOLER button to the lowest setting.
and HOTTER
but-
3.
Turn off all electrical power to the appliance if
service is to be performed.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Water Heater Operation
Checking the Draft
Figure 29 below shows the water heater’s sequence of operation
when a call for heat is initiated. The ignition control module will
attempt to light the burner three times. If the ignition control does
not detect ignition it will enter lockout mode, indicated by display
flashing status code (see status code 3 page 38 and/or status
code 8 page 39).
WARNING
Burn Hazard
Do not touch vent.
Doing so can result in burns.
SEQUENCE OF OPERATION
After successfully lighting the water heater, allow the unit to
operate for 15 minutes and check the draft hood relief opening
for proper draft (Figure 30). Make sure all other appliances in the
area are operating and all doors/windows are closed when
performing the draft test. Pass a match flame or smoke around
the relief opening of the draft hood. A steady flame or smoke
drawn into the opening indicates proper draft.
Call for heat indicated by
flashing of display screen
status codes.
Gas valve/thermostat will open
for 4 second trial for ignition
and fan will turn on.
Gas valve/thermostat will do a
relay check (relay clicks will be
heard).
Flue Products Vented
to Ouside of Building
Main burner flame is detected by
flame sense rod. Air intake fan
and main burner will continue to
operate until water temperature
inside the tank reaches
temperature set point.
Dilution Air
Display will show temperature
set point during call for heat.
Dilution Air
Draft Hood
Match
Gas valve/thermostat is de-
energized and air intake fan
continues for a post purge time
of approximately 5 seconds.
Draft Blower is energized.
Dilution Air
(Relief Opening)
Air is drawn in for
System will verify pressure
switch operation and start a
5 second pre-purge, then air
intake fan will turn off.
combustion. Keep
area clean and free
from combustibles
and flammable vapors.
Water heater returns to standby
mode.
Ignitor will start a 12 second
warm up period. “IGN” will
show on display.
FIGURE 29.
6” Maximum
Air Gap
Floor Drain
Outer Door
The water heater must be installed according to all local and state
codes or in the adsence of local and state codes, the “National Fuel
Code”’ ANSI Z223.1(NFPA 54)- current edition.
FIGURE 30.
If the flame flutters or is blown out, combustion products are escaping
from the relief opening. If this occurs, do not operate the water heater
until proper adjustments or repairs are made to the vent pipe system
and/or air supply requirements.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
should be used at the hot water taps used by these people or
at the water heater. Mixing valves are available at plumbing
supply or hardware stores, see Figure 24. Follow manufacturer’s
instructions for installation of the valves. Before changing the
factory setting on the thermostat see Table 5 and Figure 32.
Using the lowest hot water temperature that meets your needs
will also provide the most energy efficient operation of the water
heater. Never allow small children to use a hot water tap, or to
draw their own bath water. Never leave a child or handicapped
person unattended in a bathtub or shower.
Burner Flames
Inspect the burner flames through the viewport and compare
them to the drawings in Figure 31. A properly operating burner
should produce a soft blue flame. Blue tips with yellow inner
cones are satisfactory. The tips of the flame may have a slight
yellow tint. The flame should not be all yellow or have a sharp
blue-orange color. Contaminated air may cause an orange
colored flame. Contact a qualified technician if the flame is not
satisfactory.
NOTE: A water temperature range of 120°F-140°F (49°C-60°C)
is recommended by most dishwasher manufacturers.
The thermostat of this water heater has been factory set at
its lowest position. It is adjustable and must be reset to the
desired temperature setting to reduce the risk of scald injury.
The electronic control display temperature should be set at
approximately 120°F (49°C) and this is the preferred starting
point, see Table 5. Some states have a requirement for a lower
setting. If you need hotter water, follow directions for temperature
adjustment, but beware of the warnings in this section.
FIGURE 31.
Water
Temperature
°F
Time for 1st
Degree Burn
(Less Severe Burns)
Time for Permanent Burns
2nd & 3rd Degree
Emergency Shut Down
(Most Severe Burns)
IMPORTANT: Should overheating occur or the gas supply fails
to shut off, turn off the heater’s manual gas control valve and the
electrical power. Call a qualified technician.
110
116
116
122
131
140
149
154
(normal shower temp.)
(pain threshold)
35 minutes
45 minutes
5 minutes
25 seconds
5 seconds
2 seconds
1 second
1 minute
Water Temperature Regulation
5 seconds
2 seconds
Water temperature over 125°F (52°C)
can cause servere burns instantly
resulting in severe injury or death.
1 second
instantaneous
(U.S. Government Memorandum, C.P.S.C., Peter L. Armstrong, Sept. 15,1978)
Children, the elderly, and the
physically or mentally disabled are at
highest risk for scald injury.
TABLE 5
Feel water before bathing or
showering.
Pressing the “COOLER”
pressing the “HOTTER”
button decreases temperature and
button increases the temperature.
Temperature limiting valves are
available.
To avoid any unintentional changes in water temperature
settings, the control has a tamper resistant feature for changing
the temperature setting. To change the temperature setting follow
these instructions:
Read instruction manual for safe
temperature setting.
1. “Unlock” the temperature indicators by holding down both
“COOLER” and “HOTTER” temperature adjustment buttons
at the same time for one second (See Figure 32). The dis-
play will light up. The display will only remain on for 30 sec-
onds if no further buttons are pressed. After 30 seconds the
control will go back to “Lock” mode (“Lock” mode indicates
a temperature setting is locked into the control memory).
Due to the nature of the typical gas water heater, the water
temperature in certain situations may vary up to 30°F (16.7 °C)
higher or lower at the point of use such as, bathtubs, showers,
sink, etc.
HOTTER WATER CAN SCALD: Water heaters are intended to
produce hot water. Water heated to a temperature which will
satisfy space heating, clothes washing, dish washing, and other
sanitizing needs can scald and permanently injure you upon
contact. Some people are more likely to be permanently injured
by hot water than others. These include the elderly, children, the
infirm, or physically/mentally handicapped. If anyone using hot
water in your home fits into one of these groups or if there is a
local code or state law requiring a certain temperature water at
the hot water tap, then you must take special precautions. In
addition to using the lowest possible temperature setting that
satisfies your hot water needs, a means such as a mixing valve,
2. Release both of the temperature adjustment buttons.
A. To decrease the temperature press and release the
“COOLER” button until the desired setting is reached.
B. To increase the temperature press and release the
“HOTTER” button until the desired setting is reached.
NOTE: Should overheating occur or the gas supply fail to shut
off, turn off the manual gas control valve to the appliance.
NOTE: During low demand periods when hot water is not being
used, a lower thermostat setting will reduce energy losses and
27
Download from Www.Somanuals.com. All Manuals Search And Download.
may satisfy your normal hot water needs. If hot water use is
expected to be more than normal, a higher thermostat setting may
be required to meet the increased demand. When leaving your
home for extended periods (vacations, etc.) Set the electronic
control display temperature “COOLER” button to its lowest
setting. This will maintain the water at low temperatures with
minimum energy losses and prevent the tank from freezing during
cold weather.
3. Disconnect the electric connection by unplugging the water
heater from the wall outlet.
4. Shut off the incoming water supply to the water heater and
open a nearby hot water faucet to depressurize the water
tank.
5. Remove the manifold cover outer door and connect a hose
to the drain valve and terminate it to adequate drain or to the
exterior of the building. Open the drain valve and allow at
least 5 gallons of water from the tank to drain. Close drain
and remove hose.
Gas Control Valve/Thermostat Settings
6. Unplug the electrical connection on top of the powered
anode by pulling the wire connector up and off of the
powered anode rod electrical connector (Figure 33).
7. Remove the powered anode rod by using a ratchet and a
1
1- /16” socket turning counterclockwise (Figure 33) (Note:
Figure 33 is shown exploded). If the socket used is short well
you may have to remove the top male connector first before
removing the powered anode rod.
HOTTER
COOLER
®
8. Use Teflon tape or an approved pipe sealant on threads of
Electronic Control Display
the new powered anode rod.
FIGURE 32.
9. Prior to installing, it will be necessary to use pliers to bend
up approximately 90° the electrical male connector on the
top of the powered anode rod. The electrical connector
should be bent upward in order to allow the 1-1/16” deep well
socket to pass over the connector. Note: if using a short well
socket the male connector must first be removed (Figure 33
is shown exploded for clarity).
Powered Anode Operation
To protect the glass-lined water tank from corrosion through
electrolysis, this water heater is equipped with a non sacrificial
powered anode rod. The powered anode rod is non sacrificial
and should not need to be replaced unless damaged.
10. Place the powered anode rod in the spud (top of the tank)
and turn clockwise until the threads are hand tight. Using a
If the powered anode rod has been damaged then the powered
anode rod should be removed from the water heater tank and
replaced. IMPORTANT: If the damaged powered anode rod has
not been replaced but has been removed permanently, this will
void any warranties.
1
ratchet and 1- /16” socket tighten down water tight (Torque
should be between 65 to 120 foot pounds).
11. Open a nearby hot water faucet to purge air from the water
line. Fill water heater tank completely (Note: To assure the
water heater tank is full, keep the hot water faucet open for 3
minutes after a constant flow of water is obtained).
Powered Anode System
12. After turning off the hot water faucet, check for water leaks
around powered anode rod and immediately correct any if
found.
To ensure a long, trouble-free
operating life, this water
Powered
Anode
heater is equipped with a
powered anode system.
Rod
13. Upon determining there’s no water leak at the newly installed
powered anode rod, reconnect the electrical plug connector
to the top of the anode male terminal.
The powered anode rod is of
a permanent design and does
not need replacing unless
damaged.
14. Plug the electric transformer in the wall outlet and turn the
gas supply back on to the gas control valve/thermostat.
15. Turn the gas control switch to the “ON” position (located on
the side of the gas control valve/thermostat (Figure 28).
FIGURE 33.
16. To restart the water heater, follow the directions on the
“Lighting and Operating Instructions” label located on
the front of the water heater near the gas control valve/
thermostat (Figure 28).
NOTE: Whether re-installing or replacing the powered anode rod,
check for any leaks and immediately correct if found.
To replace the powered anode rod:
17. Upon verifying proper operation of the water heater, replace
the manifold cover outer door.
1. Set the gas control valve/thermostat to its lowest setting by
pressing the “COOLER” and “HOTTER” buttons together
at the same time holding for 1 second. Then press the
“COOLER” button to the lowest setting (Figure 32).
TEFLON® is a registered trademark of E.I. Du Pont De Nemours and Company
2. Turn gas control switch to the “OFF” position (located right
side of the gas control valve/thermostat (Figure 28), and turn
off the gas supply to the unit.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENT
Temperature and Pressure Relief Valve
Draining and Flushing
Explosion Harzard
• Temperature-pressure relief
valve must comply with ANSI
Z21.22-CSA 4.4 and ASME
code.
• Properly sized temperature-
pressure relief valve must be
installed in opening provided.
It is recommended that the tank be drained and flushed every 6
months to remove sediment which may build up during operation.
The water heater should be drained if being shut down during
freezing temperatures. To drain the tank, perform the following
steps:
• Can result in overheating
and excessive tank pressure.
• Can cause serious injury or
death.
1. Turn off the gas to the water heater at the manual gas shut-
off valve and turn off the electrical power to the gas control/
thermostat valve.
Manually operate the temperature and pressure relief valve at
least once a year to make sure it is working properly. To prevent
water damage, the valve must be properly connected to a
discharge line which terminates at an adequate drain. Standing
clear of the outlet (discharged water may be hot), slowly lift
and release the lever handle on the temperature and pressure
relief valve to allow the valve to operate freely and return to its
closed position. See Figure 34. If the valve fails to completely
reset and continues to release water, immediately shut off the
electrial power, manual gas control valve and the cold water
inlet valve and call a qualified technician. Contact Sears Service
1-800-4-MY-HOME® (www.sears.com).
2. Open a nearby hot water faucet until the water is not longer
hot.
3. Close the cold water inlet valve.
4. Connect a hose to the drain valve and terminate it to an
adequate drain or external to the building.
5. Open the water heater drain valve and allow all the water to
drain from the tank. Flush the tank with water as needed to
remove sediment.
6. Close the drain valve, refill the tank, and restart the heater
as directed in this manual.
If the water heater is going to be shut down for an extended
period, the drain valve should be left open.
TEMPERATURE AND PRESSURE
RELIEF VALVE
IMPORTANT: Condensation may occur when refilling the tank
and should not be confused with a tank leak.
MANUAL RELIEF
VALVE
Routine Preventive Maintenance
At least annually, a visual inspection should be made of the
venting and air supply system, piping systems, and main burner.
Check the water heater for the following:
DISCHARGE LINE TO DRAIN
FIGURE 34.
•
Obstructions, damage, or deterioration in the venting
system. Make sure the ventilation and combustion air
supplies are not obstructed.
•
•
Clean any dust or debris from the screen of the air intake
chamber.
Soot and/or carbon on the main burner. Contact a qualified
technician.
•
•
Leaking or damaged water and gas piping.
Presence of flammable or corrosive materials in the
installation area.
•
•
Presence of combustible materials near the water heater.
After servicing this water heater, check to make sure it
is working properly. (See “Operating Your Water Heater”
section of this manual.)
IMPORTANT: If you lack the necessary skills required to properly
perform this visual inspection, you should not proceed, but get
help from a qualified technician.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE OF YOUR WATER HEATER
Removing the Burner from the Manifold/
Replacement Parts
Burner Assembly
IMPORTANT: The following maintenance procedures are for
the FVIR System components and should be performed by a
qualified technician.
Natural Gas Burner
1. Take off the burner by removing the two (2) screws located
underneath the burner.
Replacement parts may be ordered from Sears Parts and Service
Centers or by calling 1-800-4-MY-HOME (1-800-469-4663).
When ordering replacement parts, always have the following
information ready:
2. Check the burner to see if it is dirty or clogged. The burner may
be cleaned with soap and hot water (Figure 36).
1. model, serial, and product number
2. type of gas
3. item number
Manifold Door Assembly
View Port
Scoop side to be
on the same side
as View Port
4. parts description
See “Parts Order List” section for a list of available repair parts.
Screws
Removing the Manifold/Burner Assembly
1. Turn off the gas supply to the water heater at the manual gas
shut-off valve. This valve is typically located beside the water
heater. Note the position of the shut-off valve in the open/on
position then proceed to turn it off (Figure 12).
Igniter/Flame
Sense Connector
Burner
(Bottom View)
2. Disconnect power supply to the heater.
FIGURE 36.
3. Remove the outer door. Remove the 2 screw securing the
manifold door assembly to the skirt.
Replacing the Flame Sense/Hot Surface igniter
Assembly
4. Disconnect all wiring connectors from the gas control valve/
thermostat (Figure 35). Disconnect the manifold tube at the gas
control valve/thermostat.
1. Remove the manifold/burner assembly. See Removing the
Manifold/Burner Assembly.
5. Grasp the manifold tube and push down slightly to free the
manifold from the gas control valve/thermostat.
2. Lift the retainer clip straight up from the back of the manifold
component block (using a flat-blade screwdriver), then
remove the manifold component block from the manifold
door (Figure 37.)
6. Carefully remove the manifold assembly from the burner com-
partment. NOTE: Be sure not to damage internal parts (Figure
39).
7. Check the burner to see if it is dirty or clogged. The burner may
be cleaned with soap and hot water.
3. Remove and keep the screw securing the flame sense/hot
surface igniter assembly (Figure 37)
4. Remove and discard the old flame sense/hot surface igniter
assembly.
Gas Control Valve/
Thermostat
5. Route the new flame sense/hot surface igniter connector
wire through manifold/burner door opening as shown in
figure 37. Secure assembly to bracket using screw removed
earlier.
Manifold Tube
Pressure
Switch / Fan,
FV Sensor
Connector
Power Supply
Transformer
Connector
Screw
Igniter/Flame
Sense
Connector
Control Display,
Anode Rod
Retainer Clip
Connector
FIGURE 35.
Flame Sense/
Hot Surface
Igniter Assembly
Manifold Component
Block
FIGURE 37.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Reposition the manifold component block in the mani-fold
door opening and secure it with the retainer clip.
Replacing the Manifold/Burner Assembly
7. See Replacing the Manifold/Burner Assembly.
WARNING
External Inspection & Cleaning of the
Air Intake Chamber Screen
1. At least twice annually inspect the air intake chamber screen
(Figure 38) for any dust or debris that may have accumulated
on the louvers. NOTE: If the water heater is located in an
area that is subjected to lint and dirt, it may be necessary to
check the air intake chamber screen
Explosion Hazard
more frequently.
Remove any fiberglass between gasket and
combustion chamber.
•
2. Use a vacuum cleaner with a hose
attachment to remove any dust or
debris that may have accumulated
on the screen.
•
•
Replace viewport if glass is missing or damaged.
Replace two piece wire connector if missing or
removed.
Air Intake Chamber
Screen
•
•
•
Replace door gasket if damaged.
Tighten both manifold door screws securely.
FIGURE 38.
Failure to follow these instructions can result in
death, explosion, or fire.
Cleaning the Combustion Chamber and Air
Diverter Assembly
1. Check the door gasket for damage or imbedded debris prior
to installation.
1. Follow procedure outlined in “Removing the Manifold/Burner
Assembly”.
2. Inspect the view port for damage and replace as required.
3. Insert the manifold/burner assembly into the burner
compartment making sure that the tip of the manifold tube
engages in the slot of the bracket inside the combustion
chamber (Figure 40).
2. Use a vacuum cleaner/shop vac to remove all loose debris in
the combustion chamber (Figure 39). Use compressed air to
clear any dust or debris that may have accumulated on the
air diverter assembly.
4. Inspect the door gasket and make sure there is no fiberglass
insulation between the gasket and the
combustion chamber.
Air Diverter
Assembly
Combustion
Chamber
5. Replace the two screws, which secure the manifold/
burner assembly door to the combustion chamber and
tighten securely. Once the manifold/burner assembly door
is tightened, visually inspect the door gasket between the
manifold/burner assembly door and the combustion chamber
for spaces or gaps that would prevent a seal. IMPORTANT:
Do not operate the water heater if the door gasket does not
create a seal between the manifold door and the combustion
chamber.
Manifold
Door Gasket
6. During the following procedure, do not cross-thread or apply
any thread sealant to any of the fittings listed below. First,
reconnect the manifold tubing to the gas control valve/
thermostat.
7. Reconnect the flame sense/hot surface igniter wire to the gas
control valve/thermostat (Figure 35).
FIGURE 39.
8. Turn gas supply on and refer to the Lighting Instructions.
9. With the burner lit, check the gas control valve/thermostat
supply line, two piece wire connector, and manifold tube
connections for leaks. Check for leaks by brushing on an
approved noncorrosive leak detection solution. IMPORTANT:
Do Not splash solution onto the electrical connections.
Bubbles forming indicate a leak. Correct any leak found. All
leaks must be fixed immediately.
3. Reassemble following the procedure under “Replacing the
Manifold/Burner Assembly”
31
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Replace the outer door (see item K page 10).
2. Reconnect the gas piping to the gas control valve/
thermostat. NOTE: Use an approved Teflon tape or pipe
compound on the gas piping connections.
3. Reconnect the manifold tube, flame sense/hot surface igniter
wire, power supply transformer, pressure switch/fan and
display connector wires (Figure 35).
Door Gasket
Burner
Slot
4. Fill the tank completely with water. NOTE: To purge the
lines of any excess air, keep the hot water faucet open for 3
minutes after a constant flow of water is obtained.
5. Turn on the gas supply and test the gas supply connections
by brushing on an approved noncorrosive leak detection
solution. IMPORTANT: Do Not splash solution onto the
electrical connections. Bubbles forming indicate a leak.
Correct any leak found.
Viewport
Manifold Tab
FIGURE 40.
6. Check the operation of the burner by following the lighting
instructions on the front of the water heater. With the burner
lit, check the gas control valve/thermostat supply line,
manifold tube connections for leaks.
Removing and Replacing the Gas Control
Valve/Thermostat
7. Verify proper operation and then replace the outer door.
IMPORTANT: Use only factory authorized replacement parts.
Removing the Gas Control Valve/Thermostat:
1. Set the gas control valve/thermostat to its lowest setting by
first depressing the COOLER
together and hold for 1 second. Then press the COOLER
button until the VAC indicator light appears (Figure 32).
and HOTTER
buttons
TEFLON® is a registered trademark of E.I. Du Pont De Nemours and Company
2. Unplug the water heater from the wall outlet.
3. Turn off the gas supply to the water heater at the manual gas
shut-off valve. This valve is typically located beside the water
heater. Note the position of the shut-off valve in the open/on
position then proceed to turn it off (Figure 12).
4. Drain the water heater. Refer to the section of “Draining and
Flushing” section and follow the procedure.
5. Disconnect the the flame sense/hot surface igniter wire,
power supply transformer, pressure switch/fan and display
connector wires from the thermostat (Figure 35). Disconnect
the manifould tube at the thermostat (Figure 35).
6. Refer to “Gas Piping” section (Figure 12) and disconnect
the ground joint union in the gas piping. Disconnect the
remaining pipe from the gas control valve/thermostat.
7. To remove the gas control valve/thermostat, thread a correctly
sized pipe into the inlet and use it to turn the gas control valve/
thermostat (counterclockwise.) Do not use pipe wrench or
equivalent to grip body. Damage may result, causing leaks.
Do not insert any sharp objects into the inlet or outlet connections.
Damage to the gas control valve/thermostat may result.
Replacing the Gas Valve:
1. To replace the gas control valve/thermostat, reassemble
in reverse order. When replacing the gas control valve/
thermostat, thread a correctly sized pipe into the inlet and
use it to turn the gas valve (clockwise.) DO NOT OVER
TIGHTEN or damage may result. NOTE: Use an approved
TEFLON® tape or pipe compound only on the threaded
section of the gas control valve/thermostat that screws into
the tank.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Start Up Conditions
NOTE: Expansion tanks are pre-charged with a 40 psi air
charge. If the inlet water pressure is higher than 40 psi, the
expansion tank’s air pressure must be adjusted to match
that pressure, but must not be higher than 80 psi.
Thermal Expansion
As water is heated, it expands (thermal expansion). In a
closed system, the volume of water will grow. As the volume of
water grows, there will be a corresponding increase in water
pressure due to thermal expansion. Thermal expansion can
cause premature tank failure (leakage). This type of failure is
not covered under the limited warranty. Thermal expansion
can also cause intermittent temperature-pressure relief valve
operation: water discharged from the valve due to excessive
pressure build up. The temperature-pressure relief valve is
not intended for the constant relief of thermal expansion. This
condition is not covered under the limited warranty.
A properly sized thermal expansion tank should be installed
on all closed systems to control the harmful effects of thermal
expansion. Thermal expansion tanks are available from Sears
stores and through the Sears Service Centers. Contact the
local plumbing inspector, water supplier and/or the Sears
Service Center for assistance in controlling these situations.
See Figure 41.
Thermal Expansion Tank Specifications
Tank
Capacity
Dimensions
in Inches
Pipe
Fitting
Model
FIGURE 41.
Number
In Gallons Diameter
Length
On Tank
153.331020
153.331050
2
5
8 (203 mm) 12-3/4 (323 mm) 3/4” Male
11 (279 mm) 14-3/4 (375 mm) 3/4” Male
Strange Sounds
TABLE 6
Possible noises due to expansion and contraction of some metal
parts during periods of heat-up and cool-down do not represent
harmful or dangerous conditions.
Expansion Tank Sizing Chart
Condensation causes sizzling and popping within the burner area
during heating and cooling periods and should be considered
normal. See “Condensation” section.
Inlet*
Water
Pressure
40psi
Water Heater Capacity (Gallons)
30
2
40
2
50
2
66
5
82
5
Expansion
Tank
Capacity
Needed
50psi
60psi
70psi
2
2
2
2
2
2
2
5
5
5
5
5
5
5
5
Draft Hood Operation
Check draft hood operation by performing a worst case
depressurization of the building. With all doors and windows
closed, and with all air handling equipment and exhaust fans
operating such as furnaces, clothes dryers, range hoods and
bathroom fans, a match flame should still be drawn into the draft
hood of the water heater with its burner firing. If the flame is not
drawn toward the draft hood, shut off water heater and make
necessary air supply changes to correct.
80psi
2
5
5
5
5
TABLE 7
*Highest recorded inlet water pressure in a 24 hour period or regulated
water pressure.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Condensation
Operational Conditions
Whenever the water heater is filled with cold water, some
condensate will form while the burner is on. A water heater may
appear to be leaking when in fact the water is condensation. This
usually happens when:
“AIR” In Hot Water Faucets
•
•
A new water heater is filled with cold water for the first time.
Burning gas produces water vapor In water heaters,
particularly high efficiency models where flue temperatures
are lower.
•
Large amounts of hot water are used in a short time and the
refill water in the tank is very cold.
Moisture from the products of combustion condense on the
cooler tank surfaces and form drops of water which may fall onto
the burner or other hot surfaces to produce a “sizzling” or “frying”
noise.
HYDROGEN GAS: Hydrogen gas can be produced in a hot water
system that has not been used for a long period of time (generally
two weeks or more). Hydrogen gas is extremely flammable and
explosive. To prevent the possibility of injury under these conditions,
we recommend the hot water faucet, located farthest away, be
opened for several minutes before any electrical appliances
which are connected to the hot water system are used (such as a
dishwasher or washing machine). If hydrogen gas is present, there
will probably be an unusual sound similar to air escaping through the
pipe as the hot water faucet is opened. There must be no smoking
or open flame near the faucet at the time it is open.
Because of the suddenness and amount of water, condensation
water may be diagnosed as a “tank leak”. After the water in the
tank warms up (about 1-2 hours), the condition should disappear.
Do not assume the water heater is leaking until there has been
enough time for the water in the tank to warm up.
An undersized water heater will cause more condensation.
The water heater must be sized properly to meet the family’s
demands for hot water including dishwashers, washing machines
and shower heads.
Do not remove the anode, leaving the tank unprotected. By
doing so, all warranty on the water heater tank is voided.
Excessive condensation may be noticed during the winter and
early spring months when incoming water temperatures are at
their lowest.
Safety Shut-off and Thermal Switch
Good venting is essential for a gas fired water heater to operate
properly as well as to carry away products of combustion and
water vapor.
This water heater is designed to automatically shut-off in the
event of the following:
1. The burner flame is extinguished for any reason.
2. The water temperature exceeds 195°F (91°C).
3. Excessive build up of dust on the louvers of the air intake
chamber. See Maintenance of your Water Heater Section.
Smoke Odor
This unit is also equipped with a flammable vapor sensor (FV
Sensor), designed to shut off the gas supply in the event the
water heater has been exposed to flammable vapors (e.g.,
spilled gasoline). NOTE: If the FV-Sense senses the presence of
flammable vapors a special FV-Sense reset sequence is required
to be input into the Electronic Control Display in order to restore
operation of the water heater.
It is not uncommon to experience a small amount of smoke and
odor during the initial start-up. This is due to burning off of oil
from metal parts, and will disappear in a short while.
A high temperature limit switch or ECO (Energy Cut Off) in the tank
is used to shut off the unit if the water temperature exceeds 195°F
(91°C). The ECO is a single-use switch, which, if activated, requires
complete replacement of the entire gas control valve/thermostat. If
the ECO should activate, the water heater cannot be used until the
gas control valve/thermostat is replaced by a qualified technician.
Contact Sears Service 1-800-4-MY-HOME® (www.sears.com).
Service
Before calling for repair service, please read the Troubleshooting
Guide in this manual. If a condition persists or you are uncertain
about the operation of the water heater, let the Sears Service
Center check it out. Contact Sears Service 1-800-4-MY-HOME®
(1-800-469-4663).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
B. *Condensation may be seen on pipes in humid weather or
pipe connections may be leaking.
Leakage Checkpoints
C. *The anode rod fitting may be leaking.
A
C
D. Small amounts of water from temperature-pressure relief
valve may be due to thermal expansion or high water
pressure in your area.
B
E. *The temperature-pressure relief valve may be leaking at
the tank fitting.
E
F. Water from a drain valve may be due to the valve being
slightly opened.
G. *The drain valve may be leaking at the tank fitting.
D
H. Combustion products contain water vapor which can
condense on the cooler surfaces of the tank. Droplets
form and drip onto the burner or run on the floor. This is
common at the time of start-up after installation and when
incoming water is cold.
I. Water in the water heater bottom or on the floor may be
from condensation, loose connections, or the relief valve.
DO NOT replace the water heater until a full inspection
of all possible water sources is made and necessary
corrective steps taken.
G
H
Leakage from other appliances, water lines, or ground
seepage should also be checked.
*
To check where threaded portion enters tank, insert cotton
swab between jacket opening and fitting. If cotton is wet,
follow draining instructions in the “Draining and Flushing”
section and then remove fitting. Put pipe dope or teflon tape
on the threads and replace. When you are finished, follow
the steps in “Filling the Water Heater” in the Installation
Instructions earlier in this manual.
F
I
6” (152.4 mm)
MAXIMUM AIR GAP
FIGURE 42.
Teflon® is a registered trademark of E.I. Du Pont De Numours and Company.
Read this manual first. Then, before checking the water heater,
make sure the gas supply has been turned “OFF”, and never turn
the gas “ON” before the tank is completely full of water.
Never use this water heater unless it is completely filled with
water. To prevent damage to the tank, the tank must be filled
with water. Water must flow from the hot water faucet before
turning “ON” gas to the water heater.
A. Water at the draft hood is water vapor which has condensed
out of the combustion products. This is caused by a problem
in the vent. Contact a qualified technician.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressurized Combustion Chamber System
Operational Checklist
1. Manifold gasket properly sealed.
5. No leaks at manifold connection.
6. Manifold door screws securely tightened.
2. Viewport not damaged or cracked.
3. Combustion chamber free of debris and undamaged.
4. Manifold component block properly installed.
TROUBLESHOOTING CHART
PROBLEM
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
1. Transformer unplugged.
2. No power at outlet.
3. Thermostat defective.
1. Plug transformer back into 120 VAC. outlet.
2. Repair service to outlet.
3. Replace Thermostat.
NO HOT WATER
4. Air Intake Chamber Fan defective.
5. Pressure Switch defective.
6. Gas Valve/Thermostat Switch in “OFF
POSITION”.
4. Replace Air Intake Chamber Fan Assembly.
5. Replace Pressure Switch Assembly.
6. Move Gas Valve/Thermostat Switch to “ON POSI-
TION”.
1. Thermostat set too low.
2. Thermostat defective.
1. Set temperature control higher.
2. Replace thermostat.
INSUFFICIENT HOT WATER
3. Heater undersized.
3. Reduce hot water use.
4. Low gas pressure.
5. Incoming water is unusually cold.
6. Leaking hot water pipes or fixtures.
4. Contact dealer.
5. Allow more time for heater to reheat.
6. Have plumber check and repair leaks.
1. Low gas pressure.
1. Check with gas utility company.
2. Replace thermostat.
2. Improper calibration.
3. Thermostat set too low.
4. Water heater too small.
5. Wrong piping connections.
6. Wasted hot water.
3. Turn temperature dial to desired setting.
4. Install adequate heater.
SLOW HOT WATER
RECOVERY
5. Correct piping-dip tube must be in cold inlet.
6. Advise customer.
WATER TOO HOT
1. Thermostat set too high.
1. Set temperature control lower.
see, “WATER TEMPERATURE REGULATION”,
section.
1. Dirt in burner ports.
1. Turn off heater and gas, clean burner head.
2. Check intake venting arrangements for obstruc-
tions.
2. Combustion air path restricted.
BURNER FLAME
YELLOW - LAZY
3. Not enough dilution air for proper com- 3. Check intake venting arrangements for obsruc-
bustion.
tions.
4. Main burner line clogged.
5. Obstruction in main burner orifice.
6. Burner flame too high.
7. Flame burns at orifice/thermostat not
functioning properly.
4. Clean, locate source and correct.
5. Clean or replace orifice.
6. Check orifice and replace if necessary.
7. Replace thermostat
8. Low gas pressure.
8. Check with gas utility company.
1. Orifice too large/wrong orifice.
2. High gas pressure.
3. Water heater flue or vent system
blocked.
1. Replace with correct-orifice.
2. Check with gas utility company.
BURNER FLAME FLOATS
AND LIFTS OFF PORTS
3. Clean flue and burner-locate source and correct.
4. Cold drafts.
4. Locate source and correct.
1. Insufficient secondary air.
1. Provide ventilation to water heater. Check
flue.
COMBUSTION ODORS
2. Water heater flue or vent system
blocked.
3. Heater installed in a confined area.
2. Clean, locate source and correct.
3. Provide fresh air ventilation.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
continued:
PROBLEM
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
1. Improperly sealed, hot or cold supply
connections, relief valve, drain valve or
thermostat threads.
1. Tighten threaded connections.
WATER LEAKS
2. Leakage from other appliances or
water lines.
2. Inspect other appliances near water heater.
3. See “START UP CONDITIONS”, section.
4. Use a pressure reducing valve and relief valve.
3. Condensation of flue products.
4. Excessive water pressure.
5. Heater stacking.
6. Closed water system.
5. Lower the thermostat setting.
6. See “Closed System/Thermal Expansion”.
1. Thermal expansion in closed water
system.
2. Improperly seated valve.
1. Install thermal expansion tank (DO NOT plug T&P
valve).
LEAKING T&P
2. Check relief valve for proper operation (DO NOT
plug T&P valve.
1. High sulfate or mineral content in water 1. Drain and flushing heater thoroughly then refill.
supply.
HOT WATER ODORS
2. Bacteria in water supply.
2. Chlorinate water supply.
1. Condensation dripping on burner.
2. Sediment at bottom of heater tank.
1. See “START UP CONDITIONS”, section.
2. See “DRAINING AND FLUSHING”, section.
WATER HEATER SOUNDS
SIZZLING-RUMBLING
1. Insufficient secondary air.
1. Provide ventilation to water heater. Check flue way,
flue baffle, burner.
SMOKING AND CARBON
FORMATION (SOOTING)
2. Low gas pressure.
3. Water heater flue or vent system
blocked.
4. Thermostat not functioning properly.
5. Heater installed in a confined area.
6. Burner flame yellow-lazy.
2. Check with gas utility company.
3. Clean, locate source and correct.
4. Replace thermostat.
5. Provide fresh air ventilation.
6. See “Burner Flame Yellow-Lazy”.
1. Thermostat set too high.
2. Sediment or lime in tank.
3. Water heater too small for job.
1. Set temperature to lower setting.
2. Drain/flush-provide water treatment if needed.
3. Install adequate heater.
HIGH OPERATION COSTS 4. Wrong piping connections.
5. Leaking faucets.
4. Correct piping-dip tube must be in cold inlet.
5. Repair faucets.
6. Gas leaks.
7. Wasted hot water.
8. Long runs of exposed piping.
9. Hot water piping in exposed wall.
6. Check with utility-repair at once.
7. Advise customer.
8. Insulate piping.
9. Insulate piping.
THERMOSTAT FAILS TO
SHUT-OFF
1. Thermostat not functioning properly.
2. Improper calibration.
1. Replace thermostat.
2. Replace thermostat.
1. Excessive water pressure.
2. Heater stacking.
1. Use a pressure reducing valve and relief valve.
2. Lower the thermostat setting.
DRIP FROM RELIEF VALVE
3. Closed water system.
3. See “CLOSED SYSTEM/THERMAL EXPAN-
SION”, section.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONIC CONTROL DISPLAY TROUBLESHOOTING
ELECTRONIC CONTROL DISPLAY
Please check guidelines below. For your safety, water heater service should be performed only by a qualified service person.
Read the GENERAL SAFETY INFORMATION supplied by the water heater manufacturer.
CONTROL DISPLAY STATUS
“POWER” Flashing
PROBLEM
SOLUTION
1. Check the 5-conductor data cable that
runs between the upper and lower
controls. Check that the wiring is not
broken, and the connectors on both ends
are properly seated in the mating
connectors.
1.
Communication Error
The system has detected a
communication error between the
upper and lower controls.
2. Replace the upper control, if the error code
does not clear - cycle power to the water
heater “Off” and “On” to reset.
3. Replace the lower control if the problem persists.
1. Turn the power off for 10 to 20 seconds
then on again to clear the error code.
2.
3.
“HEATING” and “SHORT” Flashing
“HEATING” and “OPEN” Flashing
The self-diagnostic tests have
found a problem with an internal
circuit.
2. If the error code persists or cannot be
cleared, replace the lower control.
1. Gas supply is turned off – pressure too
low. Ensure supply and manifold gas
pressures are within requirements in the
installation manual. Manifold gas
pressure is non-adjustable, if pressure is
off by more than 0.3” W.C. (75 Pa)
replace the lower control.
Ignition/flame failure.
The water heater has reached the
maximum number of retries and is
currently locked out for one hour.
Cycle the power to the water
heater off and on to reset.
2. Low supply voltage – should be 115 –
125 VAC.
3. Ensure flame sensor is making good
contact with the burner flame, ensure
flame is steady.
4. Ensure the flame sensor is clean – use
TM
ultra fine steel wool or Scotch-Brite pad
to clean the flame sensor.
5. Ensure the hot surface ignitor is
positioned to provide consistent ignition.
6. Check for any cracks in the ignitor
assembly ceramic insulators – replace
ignitor assembly if damaged.
7. Check resistance of the ignitor at room
temperature (77°F – 25°C) at the plug
end. Replace ignitor if the resistance is
not within 1.72 to 2.4 ohms at room
temperature.
1. Ensure flame sensor is making good
contact with the burner flame, ensure
flame is steady.
4.
5.
“HEATING”, “OPEN”, and “SHORT” Flashing
“ECO” and “OPEN” Flashing
Weak flame sensor current.
2. Ensure the flame sensor is clean – use
TM
ultra fine steel wool or Scotch-Brite pad
to clean the flame sensor.
1. Turn the power off for 10 – 20 seconds
Water temperature in the tank has
exceeded 185°F (85°C) and has
activated the ECO.
then on again to clear this error code.
2. Replace the lower control if the error
code persists.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL DISPLAY STATUS
PROBLEM
SOLUTION
1. Clean the screen on the combustion air
intake chamber. Turn the power “OFF” for
10 to 20 seconds then “ON” again to clear
the error code. If the problem persists:
2. Ensure the pressure switch sensing tube
is in good condition and securely
connected at both ends.
6.
“P-SW”, “OPEN”, and “CLEAN SCREEN” Flashing
The air pressure switch contacts
remain open longer than 11
seconds after the combustion fan
is energized.
3. Ensure the inner door to the combustion
chamber is secure and the gasket is
properly sealing.
4. Check operation of the air intake chamber
fan and pressure switch.
A. Turn off power to the water heater.
B. Remove the tubing from the pressure
switch and the wires from both
terminals of the pressure switch.
C. Connect a digital manometer to the
open end of the tubing from the air
intake chamber. Turn on the power to
the water heater and when the fan turns
on, measure the pressure reading in the
tubing. If the pressure reading reaches
the .22” WC make point of the pressure
switch, turn off power to the water
heater and reconnect tubing to the
pressure switch. If pressure reading does
not reach the .22” WC make point, check
the system and tubing for restrictions
and cleanliness.
D. Attach leads of ohmmeter or continuity
tester to the terminals of the pressure
switch. Turn on power to the water
heater and when the air intake fan
comes on, check for continuity across
the pressure switch contacts. If switch
contacts remain open (no continuity)
while the fan is in operation - replace
the pressure switch.
1. Turn off power to the water heater.
7.
“P-SW” and “SHORT” Flashing
The air pressure switch contacts
remain closed for more than 5
seconds when they should be
open.
2. Locate the pressure switch wiring –
ensure pressure switch wiring is correct
and not jumped.
3. Remove wires to both terminals on
pressure switch.
4. Check pressure switch contacts with an
ohmmeter for continuity.
A. If pressure switch contacts show
continuity (closed circuit) replace
the pressure switch.
B. If pressure switch contacts show
open circuit and all wiring is correct
– replace the lower control.
1. Check all wiring to the hot surface ignitor.
8.
“IGN” Flashing
Open ignitor circuit
2. Check the 3 pin Molex ignitor assembly
plug and receptacle on the lower control
for a good connection. Repair or replace
parts if necessary.
3. Check resistance of the ignitor with an
ohmmeter on the ignitor assembly plug.
Replace ignitor if resistance is not within
1.72 and 2.40 ohms.
4. If above checks are good – turn off
power for 10 seconds and then back on.
If this error code will not clear and the
ignitor resistance is within specifications
– replace the lower control.
Flammable Vapor Sensor has
detected the presence of
flammable vapors and is in lockout
1. Do not touch any electrical switch, do not use
any phone in the building and do not try to
light any appliance.
9.
“FV-SENSE” Flashing
2. Smell around the water heater to ensure there
are no gas leaks at the gas control valve or in
the supply gas line or for any other type of
flammable vapors in the area.
3. Carefully inspect the area surrounding the
water heater for any substances such as gas-
oline, paint, paint thinners, varnish, or cleaners
that could emit flammable vapors. Remove
anything that can potentially emit flammable
vapors from the area and store it properly in a
different location.
~ continued next page ~
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL DISPLAY STATUS
“FV-SENSE” Flashing
PROBLEM
SOLUTION
4. System must be manually reset by entering a
special FVS reset sequence into the Electronic
Control Display. See Electronic Control
9.
(Continued from previous page)
Display - FV - Sense Reset Sequence in
the Kenmore PCC Water Heater Service
Handbook.
The air pressure switch contacts
remain open longer than 5
seconds after the combustion fan
is energized.
1. Clean the screen on the combustion air
intake chamber, retest.
10.
11.
“LDO-SW”, “OPEN”, and “CLEAN SCREEN”
Flashing
2. If the problem persists: Cycle power to the
water heater “OFF” and “ON” to reset.
1. Check all wiring to the flammable vapor
sensor.
“FV-SENSE” and “OPEN” Flashing
Flammable Vapor Sensor is open
2. Remove the connectors from the
flammable vapor sensor and measure
the resistance of the sensor with an
ohmmeter.
A. If the reading taken is more than
1.7 million ohms, replace the
flammable vapor sensor.
B. If the reading taken is less than 1.7
million ohms, and the wiring from
the control to the sensor is good,
replace the lower control.
1. Check all wiring to the flammable vapor
sensor.
12.
“FV-SENSE” and “SHORT” Flashing
Flammable Vapor Sensor is
shorted
2. Remove the connectors from the
flammable vapor sensor and measure
the resistance of the sensor with an
ohmmeter.
A. If the reading taken is less than
2000 ohms, replace the flammable
vapor sensor.
B. If the reading taken is more than
2000 ohms, and the wiring from the
control to the sensor is good,
replace the lower control.
1. Turn power off for 10 to 20 seconds then
on again to clear this error code.
13.
14.
15.
“THMSTR” and “OPEN” Flashing
“THMSTR” and “SHORT” Flashing
All Segments Flashing
The self-diagnostic test has
detected the temperature sensor
(thermistor) inside the immersion
probe is open.
2. This part of the control cannot be
replaced or serviced. If the error code
cannot be cleared, the lower control must
be replaced.
1. Turn power off for 10 to 20 seconds then
on again to clear this error code.
The self-diagnostic test has
detected the temperature sensor
(thermistor) inside the immersion
probe is shorted.
2. This part of the control cannot be
replaced or serviced. If the error code
cannot be cleared, the lower control must
be replaced.
1. Press and release each of the
The self-diagnostic check has
detected one or both of the
temperature adjustment buttons
are stuck.
temperature adjustment buttons. If the
above action does not clear the error, the
control will continue to regulate the water
temperature at the last setting. However,
settings will no longer be adjustable – the
upper control should be replaced.
1. Check the wire that runs from the power
anode to the upper control. Check the
wire for damage, and to ensure that the
connectors are fully seated into the
mating connectors on both ends.
16.
“P-ANODE” and “OPEN” Flashing
No current to Power Anode.
2. Check that the tank is full of water. Never
use this water heater unless it is
completely full of water. To prevent
damage to the tank, the tank must be
filled with water. Water must flow from
the hot water faucet before turning “ON”
gas to the water heater.
3. Cycle power to the water heater “OFF” and
“ON” to reset.
1. Turn the power off for 10 to 20 seconds
then on again to clear the error code.
17.
“P-ANODE” Flashing
Power Anode circuit failure.
2. If the error code persists or cannot be
cleared, replace the upper control.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING FLOWCHART
APPLY POWER TO
APPLIANCE
NO
REQUEST
FOR HEAT
PRESENT?
3 MINUTE
AUTOMATIC RESET
TIME DELAY
YES
WAIT FOR PRESSURE
SWITCH TO OPEN
DISPLAY ERROR
IS
NO
PRESSURE SWITCH
PROVEN OPEN WITHIN
NUMBER
7
5
SECONDS?
YES
COMBUSTION
FAN ON
IS
WAIT FOR PRESSURE
SWITCH TO OPEN
DISPLAY ERROR
NO
PRESSURE SWITCH
PROVEN OPEN WITHIN
5
SECONDS?
NUMBER
7
IS
WAIT FOR PRESSURE
SWITCH TO CLOSE
DISPLAY ERROR
YES
NO
PRESSURE SWITCH
PROVEN CLOSED
WITHIN 11
NUMBER
6
SECONDS?
ONE HOUR
AUTOMATIC RESTART
TIME DELAY
YES
PREPURGE
COMBUSTION FAN
OFF
TURN OFF
COMBUSTION FAN,
DISPLAY ERROR CODE
NO
IS
IGNITOR
OKAY?
NUMBER
8
YES
IGNITOR ON FOR
WARM-UP TIME
TURN OFF
COMBUSTION FAN
AFTER POST-PURGE
COMBUSTION
FAN OFF
DISPLAY ERROR
3
GAS VALVE OPENS
YES
IS
NO
WAIT FOR PRESSURE
SWITCH TO CLOSE
DISPLAY ERROR
PRESSURE SWITCH
PROVEN CLOSED
COMBUSTION FAN
ON
WITHIN
5
NUMBER
6
SECONDS?
MAIN
BURNER LIGHTS
AND IS SENSED
DURING TRIAL
FOR
YES
NO
LESS
GAS VALVE CLOSES
INTERPURGE
THAN
3
TRIES
FOR IGNITION?
IGNITION
NO
YES
IGNITOR TURNS OFF
YES
LOST
IS
YES
GAS VALVE CLOSES
FLAME SENSE
LOST?
LESS THAN
TIMES?
4
NO
NO
IS
WAIT FOR PRESSURE
SWITCH TO CLOSE
DISPLAY ERROR
NO
PRESSURE SWITCH
PROVEN CLOSED
WITHIN
SECONDS?
5
NUMBER
6
Please Note:
The control continually monitors
YES
internal circuits and external sensors.
Error codes noted above, and those for
self-diagnostic faults can be found on
pages 38 through 40.
YES
IS
COMBUSTION FAN
OFF AFTER POST-
PURGE DELAY
REQUEST FOR HEAT
SATISFIED?
GAS VALVE OFF
NO
41
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDER LIST
KENMORE® ELITE HIGH EFFICIENCY PCC
(Pressurized Combustion Chamber)
NATURAL GAS WATER HEATERS
3
1
2
4
MODEL NUMBERS
153.332620
153.332640
40 Gallon Tall (Natural)
50 Gallon Tall (Natural)
5
8
6
9
7
21
10
12
13
16
19
17
20
11
12
14
18
14
15
Key
No.
Parts Description
153.332620
153.332640
1
2
Draft Hood
9007362005
9007363005
9003719015
9003719015
9007324005
9007364005
9000728015
9007320005
9007316005
9007322005
9000580015
9006948005
185760-000
9007626005
9007362005
9007363005
9003719015
9003719015
9007324005
9007364005
9000728015
9007320005
9007316005
9007322005
9000580015
9006948005
185760-000
9007627005
Flue Baffle
3
Nipple (Hot)
4
Nipple (Cold)
Anode Rod
5
6
Cold Water Inlet Tube
7
Temperature and Pressure Valve
Electronic Control Display
Air Intake Chamber
8
9
10
11
12
13
14
Gas Control Valve/Thermostat
Drain Valve
Natural Gas Burner
Hot Surface Igniter (HSI)
Manifold Door Assembly (Includes: Manifold, Door, Burner,
Burner Orifice, Hot Surface Igniter, Manifold Door Gasket and
Manifold Component Block)
15
16
17
18
19
20
21
Manifold Component Block w/Retainer Clip
Manifold Door Gasket
FV Sensor
9006449015
9006141015
9005968015
186295-002
9007311005
9007323015
9007314005
9006449015
9006141015
9005968015
186295-002
9007311005
9007323015
9007314005
Outer Door
Electrical Transformer
Pressure Switch
Air Intake Chamber Fan
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE
FOLLOWING INFORMATION:
Now that you have purchased your gas water heater,
should a need ever exist for repair parts or service,
simply contact any Sears Service Center or call
1-800-4-MY-HOME® (1-800-469-4663). Be sure to
provide all pertinent facts when you call or visit.
• MODEL NUMBER
• SERIAL NUMBER
• TYPE GAS - NATURAL
• PART DESCRIPTION
THIS IS A REPAIR PARTS LIST, NOT A PACKING LIST.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For troubleshooting, product manuals and expert advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada / TM Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros países
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
|