Sears Garage Door Opener 13953776 User Guide

MODEL 139.53776  
MULTI-FUNCTION KEYLESS ENTRY  
OWNER'S INSTRUCTIONS  
To comply with FCC rules, adjustment or modification of receiver and/or transmitter  
is prohibited, except for changing the code setting and replacing the transmitterl  
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.  
FEATURES OF THE MULTI-FUNCTION KEYLESS ENTRY  
This remote control can be used with any 53000SRT series  
garage door opener receiver.  
Personalized Code: Up to 10,000 possible combinations.  
Code can easily be changed if desired.  
WARNING  
Operation: Opener activates when 4-digit code and ENTER  
button are pressed.  
Children operating or playing with a garage door opener  
can injure themselves or others. The garage door could  
close and cause serious injury or death.  
If wrong numbers are accidentally pressed, correction can be  
made immediately. The ENTER key will transmit only the last  
four digits.  
Install the door control (or any additional push buttons)  
out of the reach of children and away from all moving  
parts of the door and door hardware, but where the  
garage door is visible. Do not allow children to operate  
the push button(s) or the remote control(s).  
The keypad will blink for 15 seconds after the code is  
transmitted. During that time you can STOP or REVERSE door  
travel just by pressing the ENTER key.  
The Multi-Function Keyless Entry can be used with any  
'SMART' receiver. The keypad will illuminate for 5 seconds at  
the first push of ANY key.  
A moving garage door could injure someone under it.  
Activate the opener only when the door is properly  
adjusted, you can see it clearly, and there are no  
obstructions to door travel.  
All 53000SRT garage door opener receivers have a separate  
memory channel for the Multi-Function Keyless Entry to  
operate the opener.  
Power Supply: 12 Volt battery.  
Open the keypad cover and remove the battery compartment screw. Set cover aside and remove battery. NOTE BATTERY  
POLARITY AS MARKED ON COMPARTMENT. Follow the installation instructions described below.  
SETTING THE CODE  
You may want someone to help at this point.  
INSTALLATION  
Plug  
1. Center the keypad at eye level  
against the selected location on  
the garage exterior (as shown  
below).  
The following procedure prevents the opener from learning the  
code of another remote control that is transmitting.  
1. Decide on a 4-digit code using numbers from 0 to 9. You can  
use a number more than once (for example, 4, 0, 4, 1).  
NOTE: For a one-piece door on  
a brick, stone or aluminum  
sided garage, use the optional  
location shown in the illustration  
to avoid injury as the door swings up  
and out.  
2. Press the selected code digits on the keypad. PRESS AND  
HOLD the ENTER button. The keypad light will blink. Press  
the 'Smart' button on the opener end panel. The adjacent  
indicator light will flash and the door will begin to move. The  
receiver has now learned the selected keypad code.  
Battery  
Cover  
2. Hold keypad firmly with cover half  
open so both top and bottom  
mounting holes are visible. Use a  
punch to mark each hole. Drill two 1/8"  
After programming the  
GARAGE DOOR OPENER RECEIVER  
keypad, test your  
Battery  
(With "Smart" Button)  
portable remote control.  
1
2
3
If the pushbutton(s) no  
longer activates the door  
opener, reprogram the  
remote control.  
pilot holes. Fasten securely with screws provided.  
3. Insert the plug provided into top hole to cover the fastening  
screw. Return the battery, being sure to observe polarity.  
Refasten compartment cover.  
9
9
1
1
To change your code  
at any time, repeat  
Steps 1 and 2.  
7
7
3
3
5
5
KG  
KG  
"Smart"  
Button  
Indicator  
Light  
Keypad  
KEYPAD MUST BE INSTALLED  
WITHIN SIGHT OF THE DOOR  
BATTERY: The 12 Volt battery should produce power for at  
least one year. As long as there is adequate power, the keypad  
will illuminate and receiver will operate when number and  
ENTER keys are pressed. Replace the battery when keypad  
illumination becomes dim.  
Exterior Front Wall  
1-Piece or  
Sectional Door  
Door Jamb Edge  
(Optional Location  
for 1-Piece Door)  
Door Jamb Face  
Sectional Door Only  
©1994, Sears Roebuck & Company  
All Rights Reserved  
114A1399D  
Printed in Mexico  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Security Camera DPQS001E User Guide
Raymarine GPS Receiver ST7001 User Guide
Saeco Coffee Makers Coffeemaker HD8833 User Guide
Samsung Printer ML 3051N User Guide
Sanyo CRT Television AVM 3259S User Guide
Sapphire Audio Speaker Sapphire XLs User Guide
Sears Garage Door Opener 13953776 User Guide
Sebo Vacuum Cleaner K2 KOMBI and K2 TURBO User Guide
Sennheiser Headphones 502013 User Guide
Sennheiser Headphones HD 410 User Guide