Integrated High Definition
LED Television User’s Guide:
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
If you need assistance:
Call Toshiba Customer Support Center:
Within the United States at (800) 631-3811
Outside the United States at (949) 583-3050
For more information, see “Troubleshooting” on page 120 in this guide.
Owner's Record
The model number and serial number are on the back and side of your TV.
Record these numbers in the spaces below. Refer to these numbers whenever you
communicate with your Toshiba dealer about this TV
Model number: ______________________________________________
Serial number: _______________________________________________
Note: To display a High Definition
picture, the TV must be receiving a
High Definition signal (such as an over-
the-air High Definition TV broadcast, a
High Definition digital cable program, or
a High Definition digital satellite
program). For details, contact your TV
antenna installer, cable provider, or
satellite provider
GMA300009010
1/12
Download from Www.Somanuals.com. All Manuals Search And Download.
3
glass and a toxic liquid. If the liquid comes in
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
contact with your mouth or eyes, or your skin is
cut by broken glass, rinse the affected area
thoroughly with water and contact your doctor
immediately.
•
ALWAYS contact a service technician to inspect
the TV any time it has been damaged or
dropped.
4) Follow all instructions.
5) Do not use this apparatus near water.
15) CAUTION:
6) Clean only with dry cloth.
•
To reduce the risk of electric shock, do not use
7) Do not block any ventilation openings. Install in
the polarized plug with an extension cord,
receptacle, or other outlet unless the blades can
be inserted completely to prevent blade
exposure.
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
•
To prevent electric shock, match wide blade of
plug to wide slot; fully insert.
9) Do not defeat the safety purpose of
the polarized or grounding type
16) CAUTION:
Do not let children swallow any small parts
plug. A polarized plug has two
•
blades with one wider than the
included on or with the product or play with the
plastic bag. Keep the small parts and the plastic
bag out of the reach of children.
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
17) CAUTION:
Do not let water or other liquids come into
•
contact with the product, as it may result in
damage.
10) Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
18) WARNING:
•
To prevent the spread of fire, keep candles or
other open flames away from this product at all
times.
11) Only use attachments/accessories specified by
•
Keep the product away from direct sunlight, fire
or a heat source such as a heater. This may
reduce the product lifetime or result in fire.
the manufacturer.
12) Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use caution
when moving the cart/apparatus
combination to avoid injury from
tip-over.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and
heed all warnings when installing your TV:
13) Unplug this apparatus during lightning storms
19)
WARNING: NEVER expose the
batteries to excessive heat such
as sunshine, fire, or the like.
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
20) ALWAYS plug the product into an outlet that is
located in such a manner that it can be easily
unplugged in case the product requires service.
21) NEVER route the product’s power cord inside a
wall or similar enclosed area.
22) Never modify this equipment. Changes or
modifications may void: a) the warranty, and b) the
user’s authority to operate this equipment under
the rules of the Federal Communications
Commission.
Additional Safety Precautions
14a) CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV
does not operate normally, take the following
precautions:
23)
DANGER: RISK OF
SERIOUS PERSONAL
INJURY, DEATH, OR
EQUIPMENT DAMAGE!
•
ALWAYS turn off the TV and unplug the power
cord to avoid possible electric shock or fire.
Never place the TV on an unstable
cart, stand, or table. The TV may
fall, causing serious personal injury,
death, or serious damage to the TV.
•
NEVER allow your body to come in contact with
any broken glass or liquid from the damaged
television. The LCD panel inside the TV contains
Download from Www.Somanuals.com. All Manuals Search And Download.
4
24) When selecting a location for the TV,
•
NEVER allow any part of the TV to hang over
the edge of the supporting furniture,
•
NEVER place the TV on tall furniture (for
example, entertainment centers or bookcases)
without anchoring both the furniture and the TV
to a suitable support,
•
•
Never place cloth or other material between the
TV and the supporting furniture.
NEVER allow children to climb on the TV
25) To avoid damage to this product, never place or
store the TV in direct sunlight; hot, humid areas; or
areas subject to excessive dust or vibration.
34)
DANGER: RISK OF SERIOUS
26) Always place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the
unit. To secure the TV, use a sturdy strap from the
hook(s) on the rear of the TV to a wall stud, pillar,
or other immovable structure. Make sure the strap
is tight, secure, and parallel to the floor.
PERSONAL INJURY OR DEATH!
•
•
Use extreme care to make sure you are never in
a position where your body (or any item you are
in contact with, such as a ladder or screwdriver)
can accidentally touch overhead power lines.
Never locate the antenna near overhead power
lines or other electrical circuits.
Never attempt to install any of the following
during lightning activity: a) an antenna system;
or b) cables, wires, or any home theater
component connected to an antenna or phone
system.
Sturdy strap (as short as possible)
4" min.
Hook
TV side
TV top
Care
27) The product shall not be exposed to dripping or
splashing, and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
For better performance and safer operation of your
TOSHIBA TV, follow these recommendations and
precautions:
28) Never block or cover the slots or openings in the
TV cabinet back, bottom, and sides. Never place
the TV:
35) If you use the TV in a room whose temperature is
32° F (0° C) or below, the picture brightness may
vary until the LED warms up. This is not a sign of
malfunction.
•
•
•
on a bed, sofa, rug, or similar surface;
too close to drapes, curtains, or walls; or
in a confined space such as a bookcase, built-in
cabinet, or any other place with poor ventilation.
36)
WARNING: RISK OF SERIOUS
PERSONAL INJURY, DEATH, OR
EQUIPMENT DAMAGE!
The slots and openings are provided to protect the
TV from overheating and to help maintain reliable
operation of the TV. Leave a space of at least 4
(four) inches around the TV.
•
•
Never use chemicals (such as air fresheners,
cleaning agents, etc.) on or near the TV
pedestal. Studies indicate that plastics may
weaken and crack over time from the combined
effects of chemical agents and mechanical
stress (such as the weight of the TV). Failure to
follow these instructions could result in serious
injury and/or permanent damage to TV and TV
pedestal.
Always unplug the TV before cleaning. Gently
wipe the display panel surface (the TV screen)
using a dry, soft cloth (cotton, flannel, etc.). A
hard cloth may damage the surface of the panel.
Avoid contact with alcohol, thinner, benzene,
acidic or alkaline solvent cleaners, abrasive
cleaners, or chemical cloths, which may damage
the surface. Never spray volatile compounds
such as insecticide on the cabinet. Such
products may damage or discolor the cabinet.
29) Always leave a space of at least 4 (four) inches
around the TV. The slots and openings are
provided to protect the TV from overheating and to
help maintain reliable operation of the TV.
30) Never allow anything to rest on or roll over the
power cord, and never place the TV where the
power cord is subject to wear or abuse.
31) Never overload wall outlets and extension cords.
32) Always operate this equipment from a 120V AC,
60 Hz power source.
33) Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see
Section 810 of the National Electric Code).
37) Never hit, press, or place anything on the back
cover. These actions will damage internal parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Choosing a location for your LED TV
38)
To Display your LED TV on the included Pedestal
Stand:
Observe the following safety precautions:
1) Read and follow the pedestal assembly
instructions included with the pedestal.
WARNING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into
the TV cabinet slots.
39) During a lightening storm, do not touch the
connecting cables or product.
CAUTION: Before beginning pedestal assembly,
carefully lay the front of the LCD Panel face down
on a flat, cushioned surface such as a quilt or
blanket. Leave the bottom of the unit protruding
over the edge of the surface and assemble the
pedestal as indicated below.
Note: Extreme care should always be used when
attaching the pedestal stand to avoid damage to
the LCD panel.
40) For added protection of your TV from lightning and
power surges, always unplug the power cord and
disconnect the antenna from the TV if you leave
the TV unattended or unused for long periods of
time.
41) Always unplug the TV to completely disconnect
from mains power. When the TV is turned off using
the on/off switch, it is not completely disconnected
from power and a minute amount of current is still
consumed.
2) Place the TV on a sturdy, level surface that can
support the weight of the TV.
3) Be sure to secure the TV to a wall, pillar, surface,
or other immovable structure see item 26) page 4
for additional details.
42) During normal use, the TV may make occasional
snapping or popping sounds. This is normal,
especially when the unit is being turned on or off. If
these sounds become frequent or continuous,
unplug the power cord and contact a Toshiba
Authorized Service Provider.
To Display your LED TV using a Wall Bracket:
If you decide to wall mount your LED TV, always use a
wall bracket Listed by an independent laboratory
(such as UL, CSA, ETL) that is appropriate for the size
and weight of the TV:
43)
WARNING: RISK OF SERIOUS
PERSONAL INJURY OR
EQUIPMENT DAMAGE!
1) CAUTION: Two people are required for
installation.
Never strike the screen with a sharp or heavy
object.
2) Unplug and remove any cables and/or other
component connectors from the rear of the TV.
3) Remove the screws of the VESA Mounting Pattern
show in the table below.
44) • The LCD screen of this product can be damaged
by ultraviolet radiation from the sun. When
selecting a location for the television, avoid
locations where the screen may be exposed to
direct sunlight, such as in front of a window.
CAUTION: Do not use the screws removed from
the back cover to attach the wall mount bracket to
the TV.
•
Never touch, press, or place anything on the
LCD screen. These actions will damage the LCD 4) Always use the screws supplied or recommended
screen. If you need to clean the LCD screen,
follow the instructions in item 36), on page 4.
by the wall mount manufacturer.
5) Follow the instructions provided with your wall
bracket. Before proceeding, make sure the
appropriate bracket(s) are attached to the wall and
the back of the TV as described in the instructions
provided with the wall bracket.
Service
45)
6) After attaching the appropriate bracket(s) to the
wall and the back of the TV, remove the pedestal
stand from the TV, as described below.
WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening
and removing the covers may expose you to
dangerous voltage or other hazards. Failure to
follow this WARNING may result in death or
serious injury. Refer all servicing not specified in
this manual to a Toshiba Authorized Service
Provider.
7) VESA Mounting Pattern
TV Size
19”
Hole Pattern (HxV)
100mm x 100mm
100mm x 100mm
100mm x 200mm
400mm x 400mm
400mm x 400mm
400mm x 400mm
Screw Size
M4
M4
24”
46) If you have the TV serviced:
32”
M4
•
Ask the service technician to use only
replacement parts specified by the
manufacturer.
Upon completion of service, ask the service
technician to perform routine safety checks to
determine that the TV is in safe operating
condition.
40”
M8
46”
M8
•
50”
M6
(unit in mm)
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Removing the Pedestal Stand
40”/46”/50” TV
VESA Mounting Pattern
1) Carefully lay the front of the unit face down on a
flat, cushioned surface such as a quilt or blanket.
Leave the stand protruding over the edge of the
surface.
Note: Extreme care should always be used when
removing the pedestal stand to avoid damage to
the LCD panel.
2) Remove the screws shown in the below diagram.
This will allow removal of the pedestal stand.
3) Once you have removed the screws holding the
pedestal stand in place, remove the pedestal stand
from the TV.
19”/24” TV
Four screws
Four screws
Hook
VESA Mounting Pattern
Sturdy strap
(as short as possible)
CAUTION: Always place the TV on the floor or a
sturdy, level, stable surface that can support the
weight of the unit. To secure the TV, use a sturdy strap
from the hook(s) on the rear of the TV to a wall stud,
pillar, or other immovable structure. Make sure the
strap is tight, secure, and parallel to the floor.
Four screws
32” TV
VESA Mounting Pattern
Hook Sturdy strap
Four screws
(as short as possible)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
ENERGY STAR® User Information
FCC Declaration of Conformity
Compliance Statement (Part 15):
Toshiba 19L4200U, 24L4200U, 32L4200U,
40L5200U, 46L5200U, 50L5200U Television models
comply with Part 15 of the FCC Rules.
ENERGY STAR User Information Statement: the factory
default settings of this television meet ENERGY STAR®
requirements. Changing Picture Settings may increase
energy consumption, possibly beyond the limits required for
ENERGY STAR qualification.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
The party responsible for compliance to these rules is:
Toshiba America Information Systems, Inc.
9740 Irvine Blvd., Irvine, CA 92618.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation. To
return to [Home] mode settings, select [Standard] picture
mode. [Standard] mode is recommended for normal home
use.
ENERGY STAR® qualified TV. Products
that earn the ENERGY STAR prevent
green house gas emissions by meeting
strict guidelines set by the U.S.
Ph: 800-631-3811
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by removing and applying
power to the equipment, the user is encouraged to try
to correct the interference by one of the following
measures:
Environmental Protection Agency.
ENERGY STAR and the ENERGY STAR
mark are registered U.S. marks.
Important notes about your TV
The following symptoms are technical limitations of
LCD Display technology and are not an indication of
malfunction; therefore, Toshiba is not responsible for
perceived issues resulting from these symptoms.
1) An afterimage (ghost) may appear on the screen if
a fixed, non-moving image appears for a long
period of time. The afterimage is not permanent
and will disappear in a short period of time.
2) The LCD panel contained in this TV is
manufactured using an extremely high level of
precision technology; however, there may be an
occasional pixel (dot of light) that does not operate
properly (does not light, remains constantly lit,
etc.). This is a structural property of LCD
technology, is not a sign of malfunction, and is not
covered under your warranty. Such pixels are not
visible when the picture is viewed from a normal
viewing distance.
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
•
•
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Caution: Changes or modifications to this equipment
not expressly approved by Toshiba could void the
user's authority to operate this equipment.
Note: Interactive video games that involve shooting a
“gun” type of joystick at an on-screen target may not
work with this TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Trademark Information
Copyright
This guide is copyrighted by Toshiba America Information
Systems, Inc. with all rights reserved. Under the copyright
laws, this guide cannot be reproduced in any form without
the prior written permission of Toshiba. No patent liability
is assumed, however, with respect to the use of the
information contained herein.
•
ClearFrame, CableClear, ColorStream, DynaLight,
GameTimer, SurfLock are trademarks or registered
trademarks of Toshiba America Information Systems,
Inc. and/or Toshiba Corporation.
•Audyssey EQ® provides clear, accurate,
and natural sound right out of the box.
This technology ensures you enjoy your
audio experience as much as your video.
©2012 by Toshiba America Information Systems, Inc. All
rights reserved.
Notice
•
Audyssey ABX™ technology uses
sophisticated driver analysis and low
frequency monitoring to extend the range and bass
of small speakers. This enables the system to
produce lower frequencies than would be possible
with a traditional system of the same size.
The information contained in this manual, including but not
limited to any product specifications, is subject to change
without notice.
TOSHIBA CORPORATION AND TOSHIBA
AMERICA INFORMATION SYSTEMS, INC.
(TOSHIBA) PROVIDES NO WARRANTY WITH
REGARD TO THIS MANUAL OR ANY OTHER
INFORMATION CONTAINED HEREIN AND
HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE WITH
REGARD TO ANY OF THE FOREGOING. TOSHIBA
ASSUMES NO LIABILITY FOR ANY DAMAGES
INCURRED DIRECTLY OR INDIRECTLY FROM
ANY TECHNICAL OR TYPOGRAPHICAL ERRORS
OR OMISSIONS CONTAINED HEREIN OR FOR
DISCREPANCIES BETWEEN THE PRODUCT AND
THE MANUAL. IN NO EVENT SHALL TOSHIBA BE
LIABLE FOR ANY INCIDENTAL,
•Audyssey Dynamic Volume® automatically
adjusts volume to provide a consistent
sound level between television programs,
commercials, and between the loud and soft passages
of movies.
Manufactured under license from Audyssey
Laboratories, Inc. U.S. and foreign patents pending.
Audyssey EQ®, Audyssey ABX™, and Audyssey
Dynamic Volume® are registered and licensed
trademarks of Audyssey Laboratories, Inc.
•
•
•
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
CONSEQUENTIAL, SPECIAL, OR EXEMPLARY
DAMAGES, WHETHER BASED ON TORT,
CONTRACT OR OTHERWISE, ARISING OUT OF
OR IN CONNECTION WITH THIS MANUAL OR
ANY OTHER INFORMATION CONTAINED HEREIN
OR THE USE THEREOF.
symbol are trademarks of Dolby Laboratories.
HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
•
•
MPEG Layer-3 audio coding technology licensed
from Fraunhofer IIS and Thomson.
This production contains Bitstream Vera Sans fonts
under the following copyright: Copyright © 2003 by
Bitstream, Inc. All Rights Reserved. Bitstream Vera
is a trademark of Bitstream, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Component video cables (red/green/blue) ........22
HDMI® cable
(with HDMI Logo).......................................22
Optical audio cable............................................23
Analog RGB (15-pin) computer cable ...............23
3.5mm Stereo to RCA Y-cable ..........................23
About the connection illustrations ....................23
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
10
(component video), and a satellite receiver.......25
HDMI®-CEC connection ..........................................31
Connection to the TV’s HDMI® terminal............37
Learning about the remote control..........................42
Setting channel skip................................................54
Setting the AV input mode ......................................55
Setting the HDMI® audio mode...............................55
Viewing the digital signal meter ..............................56
Setting the time zone ..............................................57
Viewing the system status ......................................57
Resetting Factory Defaults ................................58
Download from Www.Somanuals.com. All Manuals Search And Download.
Labeling the video input sources ............................61
Favorites browser .............................................65
Adding and clearing channels and inputs
TheaterWide 2...................................................72
Using the FREEZE feature .......................................77
Adjusting the picture...............................................78
Selecting the picture mode ...............................78
Adjusting the picture quality .............................79
Using closed captions.............................................80
Base closed captions ........................................80
Digital CC settings.............................................81
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
12
Selecting stereo/SAP broadcasts ......................84
Using the Dolby® Digital Dynamic Range
Using the Media Player .........................................100
Auto Start function..........................................101
To open the Media Player ...............................101
Viewing photo files .........................................103
Playing music files..........................................104
Viewing photo files and playing music
files at the same time................................105
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Using HDMI®-CEC.................................................109
HDMI®-CEC playback device (DVD
Static Gamma .................................................115
Closed caption problems ......................................124
Rating blocking (V-Chip) problems.......................124
No HDMI®-CEC operation .....................................125
HDMI® problems...................................................125
Media Player problems .........................................125
If the problem persists after trying the
solutions.........................................................125
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
14
Power maximum current ................................127
Dimensions...........................................................129
Supplied accessories ............................................130
Acceptable signal formats for PC IN, HDMI® ........130
PC IN signal formats.......................................130
HDMI® signal formats.....................................130
Appendix B: License Agreement.............................................132
Index..........................................................................................136
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter1
Introduction
Safety icons
This manual contains safety instructions that must be observed to avoid potential
hazards that could result in personal injuries, damage to your equipment, or loss
of data. These safety cautions have been classified according to the seriousness of
the risk, and icons highlight these instructions as follows:
Indicates an imminently hazardous situation which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, may result
in property damage.
NOTE
Provides important information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Features
16
Features
The following are just a few of the many exciting features of your
new Toshiba wide screen, integrated HD, LED TV:
❖
Integrated digital tuning (8VSB ATSC and QAM)—
Eliminates the need for a separate digital converter set-top box
(in most cases).
❖
❖
1366 x 768 output resolution 19L4200U, 32L4200U.
1920 x 1080 output resolution 24L4200U, 40L4200U,
46L5200U, and 50L5200U.
❖
Two HDMI® (L4200U Series)
—Digital, High-Definition Multimedia Interfaces with 1080p
the HDMI® input” on page 28
❖
❖
and shared composite video input, see “Connecting a DVD
player with ColorStream® (component video), and a satellite
receiver” on page 25
Digital Audio Out—Optical audio connection with Dolby®
Digital optical output form. “Connecting a digital audio
system” on page 33
❖
❖
❖
CableClear®—digital picture Noise Reduction, see
PC IN (Analog RGB)—Computer terminal, see “Connecting
HDMI®-CEC—Allows control of external devices from the
TV remote via HDMI® connection, see “Using HDMI®-CEC”
on page 109.
❖
❖
❖
ClearFrameTM 120 Hz anti-blur feature (for L5200U Series),
see “ClearFrame™ (L5200U Series)” on page 116.
Media Player—Allows you to view photo files and play music
files, see “Using the Media Player” on page 100.
ENERGY STAR® qualified.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Overview of installation, setup, and use
17
Follow these steps to set up your TV and begin using its many
exciting features.
1
service information. Keep this manual for future reference.
2
To choose a location for the TV:
❖
❖
Read “Important notes about your TV” on page 7.
Place the TV on the floor or a sturdy, level, stable surface
that can support the weight of the unit. Secure the TV to a
wall, pillar, or other immovable structure, see 25) on
page 4.
❖
❖
Place the TV in a location where light does not reflect on
the screen.
Place the TV far enough from walls and other objects to
overheating, which will damage the TV. THIS TYPE OF
DAMAGE IS NOT COVERED UNDER THE TOSHIBA
3
4
Do not plug in any power cords until after you have connected
all cables and devices to your TV.
Before connecting cables or devices to the TV, learn the
of cable types” on page 21.
5
Connect your other electronic device(s) to the TV, see
“Connecting an HDMI® or DVI device to the HDMI® input”
on page 28.
6
7
8
Install the batteries in the remote control, see “Installing
batteries” on page 40.
See “Learning about the remote control” on page 42 for an
overview of the buttons on the remote control.
After connecting all cables and devices, plug in the power
cords for your TV and other devices. Then press the POWER
button on the TV control panel or remote control to turn on the
TV. If the TV stops responding to the buttons on the remote
control or TV control panel and you cannot turn the TV off or
on, unplug the power cords for a few seconds and then plug
them in and try again.
9
See “Navigating the menu system” on page 47 for a quick
overview of navigating the TV’s menu system.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
18
TV front and side panel controls and connections
10 Program channels into the TV’s channel memory, see “Auto
Tuning” on page 51.
11 For details on using the TV’s features, see chapters 6 and 7.
12 For help, refer to “Troubleshooting” on page 120.
13 For technical specifications, see “Specifications” on page 126.
14 For the End User License Agreement, see “License
Agreement” on page 132
TV front and side panel controls and connections
Left side panel
TV front
TV top
(Sample Illustration) L4200U Series front and side panel controls
and connections
Left side panel
TV front
TV top
3
2
1
(Sample Illustration) L5200U Series front and side panel controls
and connections
1
2
Power On/Standby LED—Power indicator light, (glows
green when the TV power is On).
Remote sensor (embedded)—Point the remote control toward
this remote sensor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
TV back panel connections
19
3
POWER—Turns the TV On/Off. If the TV stops responding
to the buttons on the remote control or TV control panel and
you cannot turn off the TV, press and hold the POWER button
on the TV control panel for a few seconds to reset the TV.
4
5
ARROWS
/
/
/
—When a menu is onscreen, these
buttons function as up/down/left/right menu navigation
buttons.
MENU (ENTER)—Accesses the on-screen menus. When a
menu is displayed, this button also functions as the ENTER
button.
6
7
EXIT—Instantly closes an onscreen menu.
CHANNEL
/
—When no menu is onscreen, these buttons
change the channel (programmed channels only, see “Storing
channels in memory (optional)” on page 51).
8
9
VOLUME buttons
buttons adjust the volume level.
/
—When no menu is onscreen, these
INPUT—Changes the source you are viewing. Press
repeatedly to change from one source to the next.
10 USB port (L5200U Series)—Accesses JPEG or MP3 files, or
updates TV firmware.
TV back panel connections
For explanations of cable types and connections, see “Overview of
cable types” on page 21.
(Sample Illustration) L4200U Series back panel connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
TV back panel connections
20
1
2
3
4
5
8
7
Power Cord
6
(Sample Illustration) L5200U Series back panel connections
1
2
PC IN—Connects a personal computer.
HDMI® IN—High-Definition Multimedia Interface input
receives digital audio and uncompressed digital video from an
HDMI® device or uncompressed digital video from a DVI
device. HDMI® connection is necessary to receive 1080p
signals.
3
PC/HDMI-1 (Audio) IN—PC audio input terminal is shared
with an HDMI-1 analog audio input terminal, and its use can
be configured in the Audio Setup menu, see “Setting the PC
Audio” on page 99.
4
5
ANT/CABLE—Antenna input that supports analog (NTSC)
and digital (ATSC) off-air antenna signals and analog and
digital cable TV (QAM) signals.
external Dolby Digital decoder, amplifier, or home theater
system with optical audio input.
6
7
ANALOG AUDIO OUT—Analog audio outputs for
connecting an audio amplifier.
ColorStream® HD—High-resolution component video input
and shared composite video input, see “Connecting a DVD
player with ColorStream® (component video), and a satellite
receiver” on page 25.
8
USB port—Accesses JPEG or MP3 files, or updates TV
firmware.
NOTE
Component/Standard (composite) video cables carry only video
information; separate audio cables are required for a complete
connection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter2
Connecting Your TV
Overview of cable types
Before purchasing cables, know the connector types your devices
require. You can purchase cables from most stores that sell
audio/video devices.
Coaxial (F-type) cable
(Sample Illustration) Coaxial cable
Coaxial (F-type) cable connects your antenna, cable TV service,
and/or cable converter box to the ANT/CABLE input on your TV.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Overview of cable types
22
Standard A/V cables (red/white/yellow)
(Sample Illustration) Standard AV cables
Standard A/V cables (composite video) usually come in sets of
three, and connects to video devices with analog audio and
composite video output. These cables (and the related inputs on
your TV) are typically color-coded according to use: yellow for
video, red for stereo right audio, and white for stereo left (or mono)
audio.
Component video cables (red/green/blue)
(Sample Illustration) Component video cables
Component video cables come in sets of three and connects with
video devices with component video output. (ColorStream® is
Toshiba’s brand of component video.) These cables are typically
color-coded red, green, and blue. Separate audio cables are required
for a complete connection.
NOTE
Component video cables provide better picture quality than
composite video cables.
HDMI® cable
(with HDMI Logo)
(Sample Illustration) HDMI® cable
HDMI® (High-Definition Multimedia Interface) cable connects to
devices that have an HDMI® output. An HDMI® cable delivers
digital audio and video in its native format. Separate audio cables
are not required, see “Connecting an HDMI® or DVI device to the
HDMI® input” on page 28.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Overview of cable types
23
NOTE
HDMI® cables provide the best audio and picture quality.
Optical audio cable
(Sample Illustration) Optical audio cable
Optical audio cable connects receivers with Dolby® Digital or PCM
(pulse-code modulation) optical audio input to the TV’s Digital
Audio Out terminal, see “Connecting a digital audio system” on
page 33.
Analog RGB (15-pin) computer cable
(Sample Illustration) Analog RGB (15-pin) computer cable
Analog RGB (15-pin) computer cable connects a computer to the to
the TV’s PC IN terminal, see “Connecting a computer” on page 35.
NOTE
Separate audio cables are required.
3.5mm Stereo to RCA Y-cable
(Sample Illustration) 3.5mm Stereo to RCA Y-cable
3.5mm Stereo to RCA Y-cable connects an audio signal from DVI
device to TV.
About the connection illustrations
You can connect different types and brands of devices to your TV in
several different configurations. The connection illustrations in this
manual are representative of typical device connections only. The
input/output terminals on your devices may differ from those
illustrated herein. For details on connecting and using your specific
devices, refer to each device’s User's Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a VCR, antenna, cable TV, or camcorder
24
Connecting a VCR, antenna, cable TV, or camcorder
Camcorder
From Cable TV
Cable box
or antenna
AUDIO
OUT
VIDEO
IN
L
CH
CH
3
4
OUT
R
TV back panel
Stereo VCR
VIDEO
AUDIO
L
R
IN
from
ANT
IN
CH
CH
3
4
OUT
to
OUT
TV
L
R
(Sample Illustration) L4200U Series—Connecting to a VCR,
antenna, or cable TV or camcorder
TV back panel
Camcorder
From Cable TV
or antenna
Cable box
Stereo VCR
(Sample Illustration) L5200U Series—Connecting to a VCR,
antenna, or cable TV or camcorder
Items needed:
❖
❖
Coaxial cables
Standard AV cables
If you have a mono VCR, connect L/MONO on the TV to your
VCR’s audio out terminal using the white audio cable only.
❖
Standard audio cables
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
25
Connecting a DVD player with ColorStream® (component
NOTE
When you use a cable box, you may not be able to use the remote
control to program or access certain features on the TV.
When you use ColorStream® HD or Video, switch AV input mode
appropriately.
To view the antenna or cable signal:
Select ANT/CABLE video input source on the TV.*
To view basic and premium cable channels:
the TV.* Tune the TV to channel 3 or 4 (whichever channel the
cable box output is set to). Use the cable box controls to change
channels.
To view the VCR or camcorder video:
Turn On the VCR or camcorder video. Select VIDEO input source
on the TV.*
*To select the video input source, press the INPUT button on the
remote control, see “Selecting the video input source” on page 59.
NOTE
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and other
countries, and may subject you to civil and criminal liability.
Connecting a DVD player with ColorStream®
(component video), and a satellite receiver
DVD player
TV back panel
COMPONENT VIDEO
AUDIO OUT
L
R
Y
P
B
P
R
AUDIO
OUT
L
Y
PB
PR
R
VIDEO
OUT
COMPONENT VIDEO
Satellite
IN
S-VIDEO
OUT
Satellite receiver
(Sample Illustration) L4200U Series—Satellite receiver with
component video or DVD player with component video
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
26
Connecting a DVD player with ColorStream® (component
NOTE
ColorStream® and composite video cables cannot be connected
simultaneously.
TV back panel
DVD player
COMPONENT VIDEO
AUDIO OUT
L
R
Y
P
B
P
R
TV back panel
Satellite Receiver
AUDIO
OUT
L
Y
PB
PR
R
VIDEO
OUT
OUT
COMPONENT VIDEO
Satellite
IN
S-VIDEO
(Sample Illustration) L5200U Series—Satellite receiver with
component video or DVD player with component video
Items needed:
❖
❖
Coaxial cables
Standard AV cables
If you have a mono VCR, connect L/MONO on the TV to your
VCR’s audio out terminal using the white audio cable only.
❖
❖
Standard audio cables
Component video cables
❖
You can connect the component video cables (plus audio
cables) from the DVD player or satellite receiver to the
COLOR STREAM HD terminal in the TV. The COLOR
STREAM HD terminal can be used to display Progressive
(480p, 720p) and Interlaced (480i, 1080i) scan systems.
Please note that 1080p is not supported. Check the User’s
Guide of the DVD player in order to determine the best
output signal available.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
27
Connecting a DVD player with ColorStream® (component
❖
If your DVD player or satellite receiver does not have
component video, connect a standard A/V cable to the
AUDIO/VIDEO terminal. If your DVD player has
HDMI® video, see “Connecting an HDMI® or DVI device
to the HDMI® input” on page 28.
NOTE
When you use ColorStream® HD or Video, switch AV input mode
appropriately.
To view antenna or Cable channels:
Select the ANT/CABLE video input source on the TV.*
To view the DVD player:
Turn ON the DVD player. Select the ColorStream® HD video
input source on the TV.*
To view satellite programs using the component video
connections:
Turn ON the satellite receiver. Select the ColorStream® HD video
input source on the TV.*
To view the VCR or view and record antenna channels:
Turn ON the VCR. Tune the VCR to the channel you want to
watch. Select the VIDEO video input source on the TV.*
To record a TV program while watching a DVD:
Turn ON the VCR. Tune the VCR to the channel to record. Select
the ColorStream® HD video input source on the TV* to view the
DVD.
*To select the video input source, press the INPUT button on the
remote control, see “Selecting the video input source” on page 59.
NOTE
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs, and other materials is
prohibited under the Copyright Laws of the United States and other
countries, and may subject you to civil and criminal liability.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting an HDMI® or DVI device to the HDMI® input
28
Connecting an HDMI® or DVI device to the HDMI® input
The HDMI® input on your TV receives digital audio and
uncompressed digital video from an HDMI® source device, or
uncompressed digital video from a DVI (Digital Visual Interface)
source device.
This input is designed to accept HDCP (High- Bandwidth
Digital-Content Protection) program material in digital form from
EIA/CEA-861-D– compliant[1] consumer electronic devices (such
as a set-top box or DVD player with HDMI® or DVI output).
The HDMI® input can accept and display VGA, SVGA, XGA,
WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i
(60Hz), and 1080p (24Hz/60Hz) signal formats. For detailed signal
specifications, see “HDMI® signal formats” on page 130.
Supported Audio format: Linear PCM, sampling rate 32/44.1/48
kHz.
NOTE
To connect a computer to the HDMI® input, see “Connection to the
TV’s HDMI® terminal” on page 37.
To connect an HDMI® device, you will need one HDMI® cable
(type A connector) per HDMI® device.
❖
For proper operation, it is recommended that you use an
HDMI® cable with the HDMI® Logo (
).
❖
HDMI® cables transfer both video and audio. Separate analog
audio cables are not required (see illustration). See “Setting the
HDMI® audio mode” on page 55
TV back panel
Playback device
(Sample Illustration) L4200U Series—HDMI® connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting an HDMI® or DVI device to the HDMI® input
29
TV back panel
Playback device
(Sample Illustration) L5200U Series—HDMI® connections
To view the HDMI® device video:
Select HDMI 1, HDMI 2, or HDMI 3 (for L5200U Series) video
input source on the TV. (Press the INPUT button on the remote
control. For more information, see “Selecting the video input
source” on page 59.)
To connect a DVI device, you will need:
❖
HDMI® to DVI adapter cable
For proper operation, the length of an HDMI® to DVI adapter
cable should not exceed 9.8 ft (3m). The recommended length
is 6.6 ft (2m).
❖
3.5mm Stereo to RCA Y-cable
An HDMI® to DVI adapter cable transfers video only. Separate
analog audio cables are required (see illustration).
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting an HDMI® or DVI device to the HDMI® input
30
For more information, see “Setting the HDMI® audio mode”
on page 55
TV back panel
Playback device
(Sample Illustration) L4200U Series—DVI connections
TV back panel
Playback device
(Sample Illustration) L5200U Series—DVI connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
HDMI®-CEC connection
31
NOTE
NOTE
To ensure that the HDMI® or DVI device is reset properly:
❖ When turning on your electronic components, turn on the TV
first, and then the HDMI® or DVI device.
❖ When turning off your electronic components, turn off the
HDMI® or DVI device first, and then the TV.
EIA/CEA-861-D compliance covers the transmission of
uncompressed digital video with high-bandwidth digital
content protection, which is being standardized for reception of
high-definition video signals. Because this is an evolving
technology, it is possible that some devices may not operate properly
with the TV.
HDMI®-CEC connection
You can control the basic functions of connected audio/video
devices using the TV’s remote control if you connect a
HDMI®-CEC compatible audio receiver or playback device. The
HDMI®-CEC Control feature uses CEC technology as regulated by
the HDMI® standard.
TV back panel
Playback device
HDMI®-CEC DVD player, etc.)
Audio receiver
(
Playback device
HDMI®-CEC DVD player, etc.)
(
(Sample Illustration) L4200U Series—HDMI®-CEC compatible
audio receiver and playback device connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
HDMI®-CEC connection
32
TV back panel
Playback device
HDMI®-CEC DVD player, etc.)
(
Audio receiver
Playback device
HDMI®-CEC DVD player, etc.)
(
(Sample Illustration) L5200U Series—HDMI®-CEC compatible
audio receiver and playback device connections
To connect an HDMI® device, you will need one HDMI® cable
(type A connector) per HDMI® device (see “Overview of cable
types” on page 21).
NOTE
may not operate properly.
❖ For proper operation, it is recommended that you use an HDMI®
cable with the HDMI® Logo (
).
Before controlling the device(s):
❖
After completing the above connections, configure the
HDMI®-CEC Setup menu with the desired settings, see
“HDMI®-CEC input source selection” on page 111.
❖
❖
❖
The connected devices must also be configured. For details, see
the operation manual for each device.
This feature uses the CEC technology as regulated by the
HDMI® standard.
This feature is limited to models incorporating Toshiba’s
HDMI®-CEC. However, Toshiba is not liable for those
operations. Refer to the individual instruction manuals for
compatibility information.
NOTE
This feature may not work properly depending on the devices that are
connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a digital audio system
33
Connecting a digital audio system
The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby®
Digital or 2-channel down-mixed PCM (pulse-code modulation)
signal for use with an external Dolby Digital decoder or other
external audio system with optical audio input.
You will need an Optical audio cable (Use an optical audio cable
that has the larger “TosLink” connector and not the smaller
“mini-optical” connector.)
Dolby Digital decoder or
other digital audio system
TV back panel
(Sample Illustration) L5200U Series—Connecting a digital audio
system
To control the audio:
1
2
Turn on the TV and the digital audio device.
Press the MENU button on the remote control and open the
Sound menu.
3
Press the (
/
arrow) buttons to highlight Audio Setup, and
then press the ENTER button.
(Sample Image) Sound menu - Audio Setup selection
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a digital audio system
34
4
5
Press the (
/
arrow) buttons to select Digital Output
Format.
Press the (
/
arrow) buttons to select either Dolby Digital or
PCM, depending on your device, see “Audyssey ABX™” on
page 86.
(Sample Image) Audio Setup screen - Done
6
To save the new settings, highlight Done, and then press the
ENTER button.
To revert to the factory defaults, highlight Reset, and then
press the ENTER button.
NOTE
❖ Some audio systems may not be compatible with Dolby Digital
bitstream signals. Older audio systems that are not compatible
with standard optical out signals may not work properly, creating
a high noise level that may damage speakers or headphones.
THIS DAMAGE IS NOT COVERED BY YOUR WARRANTY.
❖ The DIGITAL AUDIO OUT terminal may not output some digital
audio sources because of copy restrictions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting an analog audio system
35
Connecting an analog audio system
This connection allows you to use external speaker with an external
analog audio amplifier to adjust the level.
You will need standard audio cables.
TV back panel
Audio system
(Sample Illustration) L4200/L5200U Series—Connecting an
analog audio system
Connecting a computer
With either the PC IN or HDMI® connection, you can view your
computer’s display on the TV and hear the sound from the TV’s
speakers.
Connecting a computer to the TV’s PC IN terminal
When connecting a computer to the PC IN terminal on the TV, use
an analog RGB (15-pin) computer cable and a PC audio cable. For
more information, see “Overview of cable types” on page 21.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a computer
36
TV back panel
PC audio cable
Computer
PC audio output
Conversion adaptor (if necessary)
(Sample Illustration) L4200U Series Computer connections
TV back panel
PC audio cable
Computer
PC audio output
Conversion adaptor (if necessary)
(Sample Illustration) L5200U Series Computer connections
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a computer
37
To use a computer, set the monitor output resolution on the
computer before connecting it to the TV. The supported signal
formats are VGA, SVGA, XGA, WXGA and SXGA. For detailed
signal specifications, see “Acceptable signal formats for PC IN,
HDMI®” on page 130.
Other formats or non-standard signals will not be displayed
correctly.
To display the optimum picture, use the computer setting feature,
see “Using the PC settings feature” on page 98.
NOTE
❖ The PC audio input terminals on the TV are shared with the
HDMI 1 analog audio input terminals. For configuration
information, see “Setting the PC Audio” on page 99.
❖ Some computer models cannot be connected to this TV.
❖ If the computer has a compatible mini D-sub15-pin terminal, an
adapter is not required.
❖ Depending on the content’s title and the computer’s
specifications, some scenes may be skipped or you may not be
able to pause during multi-angle scenes.
Signal names for mini D-sub 15-pin connector:
Pin No.: Signal Name: Pin No.: Signal Name: Pin No.: Signal Name:
1
2
3
4
5
R
6
Ground
Ground
Ground
5V
11
12
13
14
15
Reserved
SDA
G
7
B
8
H-sync
V-sync
SCL
Reserved
Ground
9
10
Ground
When connecting a computer with a DVI terminal on the TV, use an
HDMI®-to-DVI adapter cable and analog audio cables.
When connecting a computer with an HDMI® terminal, use an
HDMI® cable (type A connector). Separate analog audio cables
may not be necessary, depending on computer hardware and setup,
see “Connecting an HDMI® or DVI device to the HDMI® input”
on page 28.
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a computer
38
TV back panel
PC audio cable
Computer
PC audio output
HDMI® to DVI adapter cable
(Sample Illustration) L4200U Series Connections to HDMI®
terminal
TV back panel
PC audio cable
Computer
PC audio output
HDMI® to DVI adapter cable
(Sample Illustration) L5200U Series Connections to HDMI®
terminal
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Your TV
Connecting a computer
39
The supported signal formats are VGA, SVGA, XGA, WXGA,
SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz), and
1080p (24Hz/60Hz). For signal specifications, see “Acceptable
signal formats for PC IN, HDMI®” on page 130.
NOTE
❖ The edges of the picture may be hidden.
❖ If receiving a 480i (HDMI®), 480p (HDMI®), 720p, 1080i, or
1080p signal program, Native mode scales the video to display
the entire picture within the borders of the screen (i.e. no
overscanning).
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter3
Using the Remote Control
Installing batteries
To install batteries:
1
Remove the battery cover from the back of the remote control.
Squeeze tab
and lift cover
(Sample Illustration) Removing the remote back cover
2
Insert two AAA batteries, corresponding to the (+) and (-)
markings on the battery compartment.
(Sample Illustration) Installing the batteries
3
Replace the battery cover.
Do not expose batteries to excessive heat such as sunshine, fire, etc.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Remote control effective range
41
NOTE
❖ Be sure to use AAA size batteries.
❖ Dispose of batteries in a designated disposal area.
❖ Always consider the environment when disposing of batteries.
Always follow applicable laws and regulations.
❖ If the remote does not operate correctly, or if the operating range
is reduced, replace the batteries.
❖ Always replace both batteries with new ones. Never mix battery
types or use new and used batteries together.
❖ Always remove batteries from the remote if they are dead or if the
remote control is not to be used for an extended period of time.
This prevents battery acid from leaking into the battery
compartment
Remote control effective range
For optimum performance, aim the remote control directly at the
TV and make sure there is no obstruction between the remote
control and the TV.
16.4 ft (5m)
(Sample Illustration) Remote control effective range
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Learning about the remote control
42
Learning about the remote control
The buttons used for operating the TV are described below. For the
HDMI®-CEC remote control functions, see “HDMI®-CEC
playback device (DVD player, etc.) control” on page 109.
(Sample Illustration) Remote control overview
NOTE
The error message “NOT AVAILABLE” may appear if you press a
button for a function that is not available.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
1
2
3
4
5
6
the power LED indicator on the TV front glows green.
“Selecting the picture size” on page 70.
The INPUT button selects the video input source, see
“Selecting the video input source” on page 59.
The FREEZE button freezes the picture. Press again to restore
page 77.
7
The Channel Number buttons (0-9, and Dash 100) directly
tune channels. The (Dash 100) button allows you to enter two
part channel numbers, see “Storing channels in memory
“Favorites browser” on page 65.
8
9
Browser, see “Favorites browser” on page 65.
10 The CH (
/
arrow) buttons cycle through programmed
channels (when no on-screen menu is present), see “Tuning
channels using the Channel Browser” on page 64.
closed captions” on page 80.
12 The MUTE button reduces or turns off the sound, see “Muting
the sound” on page 83.
13 The VOL (+ –) buttons adjust the volume level.
information” on page 112.
15 The EXIT button closes on-screen menus.
16 The ENTER button activates highlighted items in the main
menu system.
17 The CH RTN button returns to the last viewed channel or
source, see “Switching between two channels using Channel
Return” on page 69.
Download from Www.Somanuals.com. All Manuals Search And Download.
Learning about the remote control
44
18 The Arrow buttons (
/
/
/
) select or adjust programming
menus when a menu is on-screen.
to the previous/next channel in the channel history when TV
programming is on-screen. See “Tuning channels using the
Channel Browser” on page 64.
20 The MENU button accesses the main TV menu system. See
“Navigating the menu system” on page 47
The following key functions allow you to control Toshiba
HDMI®-CEC compatible devices via HDMI® connection. See
“Using HDMI®-CEC” on page 109
21 The STOP button stops playback of the loaded DVD or tape.
22 The PLAY button begins playback of the loaded DVD or tape.
23 The SKIP forward button skips forward to locate later DVD
chapters.
24 The FF button fast-forwards the DVD or tape. (Press during
play mode to view the picture moving rapidly forward.)
25 The EJECT button ejects the DVD or tape.
26 The PAUSE/STEP button suspends play or record temporarily.
Press during play or record mode to pause the picture; press
again to restart.
27 The SKIP reverse button skips to the beginning of the current
DVD chapter or locates the previous chapter.
28 The REW button rewinds/reverses the tape or DVD. (Press
during play mode to view the picture moving rapidly
backward.).
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter4
Menu Layout and Navigation
Main menu layout
The tables below and on the next pages provide a quick overview of
your TV’s menu system. To open the Installation menus (illustrated
below), press MENU on the remote control or TV control panel.
Icon
Item
Option
Picture
Mode
Dynamic/Standard/Movie/PC/Preference
Opens the Picture Settings menu
Opens the Noise Reduction menu
Off/On
Opens the Theater Settings menu
Launches the temporary Audio Selector
Opens the Audio Settings menu
Opens the Audio Setup menu
Picture Settings
Noise Reduction
Game Mode
Theater Settings
Digital Audio Selector
Audio Settings
Audio Setup
Sound
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Layout and Navigation
Main menu layout
46
Icon
Item
Option
Preferences
CC Selector
Base CC Mode
Digital CC Settings
Input Labeling
AV Input
Launches the temporary CC Selector
Off/CC1/CC2/CC3/CC4/T1/T2/T3/T4
Opens the Digital CC Setup menu
Opens the Input Labeling menu
Selects ColorStream HD/Video input
English/Français/Español
Menu Language
Channel Browser Setup Opens the Channel Browser Setup menu
HDMI®-CEC Player
Control
Opens the HDMI®-CEC Player Control
menu
Energy Saving Settings Opens the Energy Saving Settings menu
Enable Rating Blocking Off/On (for USA region)
Locks
Setup
Edit Rating Limits
Opens the Edit Rating Limits menu (for
USA region)
Input Lock
Off/Video/Video+
Panel Lock
Off/On
GameTimer®
New PIN Code
Installation
Off/30 min/60 min/90 min/120 min
Opens the New PIN Code entry screen
Opens the Installation menu
HDMI®-CEC Setup
Enable HDMI®-CEC/TV Auto Input
Switch/TV Auto Power/Device Auto
Standby/Speaker Preference
Sleep Timer
10-minute increments, from 0 min to a
maximum of
12 hours
PC Settings
Media Player
Opens the PC Settings menu
Opens the Media Player menu
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Layout and Navigation
Setup/Installation menu layout
47
Setup/Installation menu layout
The Installation menu contains the Terrestrial and System Status
menus.
To open the Installation menu, press the MENU button on the
remote control or TV control panel, open the Setup menu, select
Installation, and then press the ENTER button.
Icon
Item
Option
Terrestrial
Input Configuration
Channel Program
Opens the Input Configuration menu
Start Scan > Scans for new channels on
ANT/CABLE
Channel Options
Time Zone
Opens the Skip/Lock Channel menu
Eastern/Newfoundland/Atlantic/Hawaii/
Alaska/Pacific/Mountain/Central
Signal Meter
Opens the Signal Meter menu
System Status
System Information
Opens the System Information screen
Navigating the menu system
You can use the buttons on the remote control or TV control panel
to access and navigate your TV’s on-screen menu system.
1
Press the MENU button to open the menu system.
(Sample Image) Navigating the menu system
2
When a menu is open, use the (
the remote control or the (
/
/
/
/
arrow) buttons on
/
/
+/- arrow) buttons on the
TV control panel to move in the corresponding direction in the
menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Layout and Navigation
Navigating the menu system
48
3
Press the ENTER button to save your menu settings or select a
highlighted item.
A highlighted menu item appears in a different color in the
menu.
4
5
All menus close automatically if you do not make a selection
within approximately 60 seconds, except the signal meter
menu, which closes automatically after a few minutes.
To close a menu instantly, press the EXIT button.
NOTE
The menu background may sometimes appear black, depending on
the signal the TV is receiving. This is not a sign of malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter5
Setting up your TV
Initial Setup
When you first turn on or reset the TV, the Initial Setup window
will appear.
1
In the Menu Language field, press the (
select your preferred language.
/
arrow) buttons to
2
Press the (
/
arrow) buttons to select Time Zone Setup.
Then set your desired time zone, using the (
/
arrow)
buttons and press the ENTER button.
The Location settings window appears.
3
For normal home use, press the (
Home, and then press the ENTER button.
/
arrow) buttons to select
The ANT/CABLE In setup window appears.
4
5
Press the (
/
arrow) buttons to select the input source
(Cable or Antenna), and then press ENTER.
Press the ENTER button to select Start Scan and continue
with the Auto Tuning.
You can stop the Initial Setup by pressing the EXIT button.
However if you do not finish the entire Initial Setup process and
press the POWER button before completing all the steps, the Initial
Setup window will appear every time you turn on the TV until
initial setup is complete.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Initial Setup
50
Menu language
You can choose from three different menu language settings
(English, Français, and Español) for the on-screen display of menus
and messages.
To select the menu language:
1
Press the MENU button and open the Preferences menu, and
highlight Menu Language.
2
Press the (
language.
/
arrow) buttons to select your preferred
(Sample Image) Selecting the menu language
Press the EXIT button to close the Preferences menu.
3
ANT/CABLE IN
This setting configures the input source for the ANT/CABLE
terminal.
1
2
Press the MENU button and open the Setup menu.
Highlight Installation, and then press the ENTER button.
(Sample Image) Setup menu - Installation selection
A new set of Installation menu icons appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Storing channels in memory (optional)
51
3
Open the Terrestrial menu, highlight Input Configuration,
and then press the ENTER button.
(Sample Image) Terrestrial menu - Input Configuration selection
4
Highlight ANT/CABLE In and press the (
to select the input source (Cable or Antenna).
/
arrow) buttons
(Sample Image) Input Configuration screen
5
To save your new settings, highlight Done, and then press the
ENTER button. To revert to your original settings, highlight
Cancel, and then press the ENTER button.
Storing channels in memory (optional)
To make sure your TV stops only on the channels you want when
you press the CH arrow buttons on the remote control or the control
panel, store those channels in the TV’s memory.
Auto Tuning
You can set up the TV to detect all active channels in your area and
store them in its memory. Then you can manually add or erase
individual channels from memory.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Storing channels in memory (optional)
52
NOTE
❖ You must set up the ANT/CABLE input source before
programming channels. See “ANT/CABLE IN” on page 50.
❖ The automatic channel programming process will erase
channels that were previously programmed into the TV’s
memory.
❖ To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
❖ Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when the
antenna input is configured for Antenna. This is normal;
however, once channel programming is finished, you should not
have to repeat the programming process again unless your
Cable TV service lineup changes significantly.
To program channels automatically:
1
Configure the antenna input source, if you have not already
done so, see “ANT/CABLE IN” on page 50.
2
3
Press the MENU button and open the Setup menu.
Highlight Installation, and then press the ENTER button.
(Sample Image) Setup menu - Installation selection
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Storing channels in memory (optional)
53
A new set of Installation menu icons appears.
4
Open the Terrestrial menu, highlight Channel Program to
open the Start Scan window, and then press the ENTER
button to begin channel programming.
(Sample Image) Terrestrial menu - Channel Program selection
(Sample Image) Auto tuning program channels
The TV will automatically cycle through all the antenna channels,
and store all active channels in the channel memory. While the TV
is cycling through the channels, the message “Scanning channels,
please wait” appears.
5
To cancel channel programming, press the EXIT button on the
remote control or highlight Cancel in the on-screen display,
and then press the ENTER button.
When channel programming is complete, press the CH arrow
buttons to view the programmed channels.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Setting channel skip
54
Setting channel skip
To prevent a channel from being viewed, you can set it to be
skipped.
1
From the Setup menu, highlight Installation, and then press the
ENTER button.
2
Press the ( arrow) buttons to select Channel Options, and
then press the ENTER button.
/
The list of channels appears.
(Sample Illustration) List of channels
Press the ( arrow) buttons to select a channel position to
3
/
be skipped, and then press the ENTER button.
A check will appear in the box. To remove the check, press the
ENTER button again.
To add a channel to the channel memory:
❖
Highlight the checked box next to the channel number you
wish to add, and then press the ENTER button to remove the
check.
NOTE
You can also block specific channels so that they cannot be tuned
until you unlock them. For information, see “Locking channels” on
page 96
To manually add digital sub-channels on a physical channel:
❖
Use the Channel Numbers and the (Dash 100) on the remote
control to enter the channel number (for example, 56–1).
If the channel is found, the number will be added to the list and
the box will be unchecked. If the channel is not found, a
message appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Setting the AV input mode
55
NOTE
Skipped channels cannot be selected with the CH arrow buttons;
however, they can be accessed using the number keys on the remote
control.
If an encrypted channel is accidentally added to the channel list
while programming channels, you can remove the unwanted
encrypted (non-viewable) channel while you are channel surfing.
To remove encrypted channels from the channel memory:
When you tune to an encrypted channel, the following message
appears.
(Sample Illustration) Removing an encrypted channel
❖
Press the 1 button while the message is displayed to remove the
unnecessary channel from the channel list.
Setting the AV input mode
This setting determines the configuration of the shared AV input on
your TV. You can set this input for either ColorStream HD or
Video.
Setting the HDMI® audio mode
To set the HDMI® audio mode:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Setup, and then press the ENTER button.
Press the (
then press the (
mode (Auto, Digital, or Analog). (Auto is the recommended
/
arrow) buttons to select HDMI 1 Audio, and
/
arrow) buttons to select the HDMI 1 audio
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Viewing the digital signal meter
56
mode.) See “Connecting an HDMI® or DVI device to the
HDMI® input” on page 28.
(Sample Image) HDMI® Audio mode selection
Description:
Mode:
When viewing the HDMI 1 input, if digital audio from the HDMI®
input is available, it will be output. If not, the TV will automatically
detect and output analog audio from the PC Audio input.
Auto
When viewing the HDMI 1 input, digital audio from the HDMI®
input will be output.
Digital
Analog
When viewing the HDMI 1 input, analog audio from the PC Audio
input will be output.
4
button.
NOTE
Because the PC and HDMI 1 inputs share the same set of analog
audio inputs, the PC Audio menu setting influences the HDMI 1
Audio menu setting. If PC Audio is set to “No” the HDMI 1 Audio
setting changes to “Auto.” If PC Audio is set to “Yes” the HDMI 1
Audio setting is set to “Digital” and is grayed out in the menu. See
“Setting the PC Audio” on page 99.
Viewing the digital signal meter
You can view the digital signal meter in the ANT/CABLE digital
TV input source only.
To view the digital signal meter:
1
Press the MENU button and open the Setup menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Setting the time zone
57
2
Highlight Installation, and then press the ENTER button.
A new set of Installation menu icons appears.
3
4
Open the Terrestrial menu, highlight Signal Meter, and then
press the ENTER button.
Press the (
/
/
/
arrow) buttons to select the antenna input
and digital channel signal you wish to check.
NOTE
❖ The physical digital channel number listed in the Signal Meter
screen may not correspond to a virtual TV channel number.
Contact your local broadcasters to obtain the RF channel
numbers for your local digital stations.
❖ The signal strength does not change between virtual channels on
the same physical channel.
To close the screen and return to the Terrestrial menu:
Highlight Done, and then press the ENTER button.
To return to normal viewing, press the EXIT button.
❖
Setting the time zone
The Time Zone setup allows you to specify the correct time zone
for your region. This feature allows the TV status information to
display the correct time zone information for your viewing area.
To set the time zone:
1
In the Setup menu, highlight Installation, and then press the
ENTER button.
2
3
Highlight Time Zone, and then press the ENTER button.
Press the (
/
arrow) buttons to select the region, highlight
Done, and then press the ENTER button.
After the time zone has been set, you will be asked to set the current
Daylight Saving Time status.
To set the Daylight Saving Time status:
❖
Press the (
/
arrow) buttons to select Yes or No, highlight
Done, and then press the ENTER button.
Viewing the system status
1
Press the MENU button and open the Setup menu.
2
Highlight Installation, and then press the ENTER button.
A new set of Installation menu icons appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your TV
Viewing the system status
58
3
4
Open the System Status menu, highlight System
Information, and then press the ENTER button.
Press the (
/
arrow) buttons to scroll through the menu bar
to select Factory Defaults or Support Information.
The related information appears.
To close the screen and return to the Installation menu:
❖
Highlight Done in the Support Information screen, and then
press the ENTER button.
To return to normal viewing, press the EXIT button.
Resetting Factory Defaults
To reset all settings and channels to their factory default values:
1
2
Press the MENU button and open the Setup menu.
Highlight Installation, and then press the ENTER button.
A new set of Installation menu icons appears.
3
4
Open the System Status menu, highlight System
Information, and then press the ENTER button.
Press the (
/
arrow) buttons to scroll through the menu bar
to select Factory Defaults.
5
6
7
Highlight Yes, and then press the ENTER button.
If a PIN code has been set, enter your PIN code.
Press the (
/
arrow) buttons to select Done, and then press
the ENTER button.
A warning message appears.
8
9
Select Yes, and then press the ENTER button.
The TV turns off automatically after a few seconds.
After the TV turns off, unplug the TV power cord and then
plug it in again to complete the reset process.
To cancel the reset process, select No, and press the ENTER button
in step 5 above.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter6
Using the TV’s features
Selecting the video input source
To select the video input source to view:
1
2
Press the INPUT button on the remote control or TV control
panel.
Do one of the following:
❖
❖
Press 0-4 (L4200U Series) or 0-5 (L5200U Series).
Repeatedly press the ( arrow) buttons on the remote
/
control, and then press the ENTER button to change the
input setting.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the video input source
60
❖
Repeatedly press the INPUT button on the remote control
or TV control panel to change the input setting.
The current signal source displays in the top right corner of the
Input Selection screen.
(Sample Image) L4200U Series Input Selection screen
VCR
(Sample Image) L5200U Series Input Selection screen
NOTE
❖ You can label the video input sources according to the specific
devices you have connected to the TV, see “Labeling the video
input sources” on page 61.
❖ Sources can be “hidden,” see “Labeling the video input sources”
on page 61.
❖ “No video signal” will appear randomly on the screen if no
signal is received in video input mode.
❖ If a CEC device is connected to an HDMI® input, the
HDMI®-CEC icon appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Labeling the video input sources
61
If a HDMI®-CEC device with HDMI® switching capability
(e.g. Audio Receiver) is connected to the HDMI® input, press the
INPUT button on the remote control or TV control panel
repeatedly to highlight HDMI 1 or HDMI 2.
If the connected CEC device has any connected devices, a separate
device selection pop-up window appears:
(Sample Illustration) HDMI® setting pop-up window
Press the INPUT button repeatedly to highlight the desired input
source, and then press the EXIT button.
NOTE
❖ When you select HDMI®-CEC input sources from the pop-up
window using the INPUT button, some HDMI®-CEC devices
may automatically turn on.
❖ When selecting input sources using the (
/
arrow) buttons,
you will need to press the ENTER button to actually select a
particular device from the pop-up window.
Labeling the video input sources
You can label each video input source according to the type of
device you have connected to each source. Choose from the
following preset list of labels:
❖
❖
❖
❖
❖
❖
❖
❖
❖
❖
❖
– – (default label)
Audio Receiver
Cable
Compact Disc
DTV
DVD
Game Console
HDMI® Switch (HDMI® inputs only)
Laser Disc
Satellite/DSS
VCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Labeling the video input sources
62
❖
❖
Video Recorder
Hide (to hide an unused input in the Input Selection screen and
in the Channel Browser Inputs list)
NOTE
If you select PC in the Input Selection screen, you can choose only
“– –”, “Game Console”, or “Hide” as the label.
To label the video input sources:
1
2
Press the MENU button and open the Preferences menu.
Highlight Input Labeling, and then press the ENTER button.
(Sample Image) Preferences menu - Input Labeling selection
3
4
Press the (
you wish to label.
/
arrow) buttons to highlight the video source
Press the ( arrow) buttons to select the desired label for
/
that input source. If a particular input is not used, Hide can be
selected as the label. This will cause that input to be grayed out
in the Input Selection screen and skipped over when you press
the INPUT button on the remote control.
(Sample Image) L4200U Series Input Labeling screen
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Labeling the video input sources
63
(Sample Image) L5200U Series Input Labeling screen
5
To save the new input labels, highlight Done, and then press
the ENTER button.
To revert to the factory default labels, highlight Reset and press
the ENTER button.
Input labeling example:
The screen below left shows the default Input Selection screen
(with none of the inputs labeled as a specific device). The screen
below (right) is an example of how you can label the inputs if you
connected a VCR to ColorStream® HD, a video recorder to
HDMI 1, and a DVD player to HDMI 2.
VCR
No inputs labeled
All inputs labeled
(Sample Image) L4200U - Input selection screens
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
64
No inputs labeled
All inputs labeled
(Sample Image) L5200U - Input selection screens
To clear the input labels:
1
2
3
Press the MENU button and open the Preferences menu.
Highlight Input Labeling, and then press the ENTER button.
Tuning channels using the Channel Browser
The Channel Browser provides an easy navigation interface for all
your channels and inputs. This feature allows you to:
❖
❖
Navigate and select entries.
Keep a list of your favorite channels, see “Favorites browser”
on page 65.
❖
❖
Quickly surf and tune your recently viewed channels/inputs
from the Channel Browser History List.
Surf via Browse mode (to immediately tune channels as you
highlight them in the Channel Browser) or Select mode (to surf
over channels in the Channel Browser before you select one to
tune).
❖
❖
Quickly change inputs from the Inputs List.
Quickly select HDMI®-CEC devices from the
HDMI®-CEC List.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
65
Favorites browser
The Favorites Browser allows you to quickly set up a favorite
channels/inputs list that is integrated into the Channel Browser.
To add a favorite channel/input:
1
2
Tune to the channel or input.
Press and hold the FAV button for a few seconds.
NOTE
The channel or input is added to the beginning of the Favorites list
on the left side of the Channel Browser.
To delete a favorite channel/input:
1
2
Press the FAV button to open the Favorites browser list.
Highlight the channel or input to delete by pressing BACK CB
or NEXT CB arrow buttons.
3
Press and hold the (Dash 100) button for a few seconds. The
channel/input will be removed from the Favorites list.
To set up the Channel Browser:
1
In the Preferences menu, highlight Channel Browser Setup,
and then press the ENTER button.
2
Press the ( arrow) button to highlight Navigation, and then
press the (
/
arrow) buttons to select either Browse Mode
or Select Mode.
(Sample Image) Channel browser setup screen
3
Press the ( arrow) button to highlight History List, and then
press the ( arrow) buttons to select On or Off.
/
NOTE
The History List will be cleared every time the TV is powered off.
4
Press the ( arrow) button to highlight ANT/CABLE List,
and then press the (
/
arrow) buttons to select On or Off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
66
5
6
7
Press the ( arrow) button to highlight Inputs List, and then
press the (
Press the ( arrow) button to highlight Favorites List, and
then press the ( arrow) buttons to select On or Off.
Press the ( arrow) button to highlight HDMI®-CEC List,
and then press the ( arrow) buttons to select On or Off.
/
arrow) buttons to select On or Off.
/
/
NOTE
HDMI®-CEC List is automatically grayed out and set to Off when
Enable HDMI®-CEC is switched to Off. See “Using HDMI®-CEC” on
page 109.
8
To save the new entries, highlight Done, and then press the
ENTER button.
To return to factory defaults, highlight Reset, and then press
the ENTER button.
To open the Channel Browser:
❖
Press BACK CB or NEXT CB arrow buttons on the remote
control.
❖
Press the BACK CB arrow button to surf backward through the
previously tuned channels in the History list, the channels in
the ANT/CABLE channel list, the inputs in the Inputs list, the
favorite channels/inputs in the Favorites list, or the
HDMI®-CEC devices in the HDMI®-CEC List.
❖
Press the NEXT CB arrow button to surf forward through the
channel History, the ANT/CABLE channel list, the Inputs list,
the favorite channels/inputs in the Favorites list, or the
HDMI®-CEC List.
Elements of the Channel Browser
(Sample Illustration) Channel Browser elements
1
2
Current list (History, ANT/CABLE, Inputs, Favorites, or
HDMI®-CEC).
Channel or input type.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
67
3
4
5
Channel or input currently being viewed.
Channel or input that is currently highlighted in the browser.
Channels stored in the History List.
To toggle among the available lists:
After opening the Channel Browser, press the (
/
arrow) buttons
to toggle through the History, ANT/CABLE, Inputs, Favorites, or
HDMI®-CEC options.
NOTE
❖ The Channel Browser opens in History List by default. Once
another list has been selected, the Channel Browser will open in
the last selected list.
❖ If all lists are turned off, pressing BACK CB or NEXT CB arrow
buttons or the FAV button will not display the Channel Browser.
If Favorites List is turned off, the FAV button will have no effect.
❖ Pressing the FAV button will display the Channel Browser
Favorites list regardless of the last selected list in the Channel
Browser.
To tune to a channel or input in Browse mode:
1
While watching TV, press BACK CB or NEXT CB arrow
buttons to display the Channel Browser and surf back to a
previous item or surf forward to the next item in the list.
In Browse mode, when you stop on an item in the Channel
Browser, it is highlighted and the TV automatically tunes to the
channel or input.
2
Press the EXIT button to close the Channel Browser.
To tune to a channel or input in Select mode:
1
While watching TV, press BACK CB or NEXT CB arrow
buttons to display the Channel Browser and surf back to a
previous item or surf forward to the next item in the list.
In Select mode, when you stop on an item in the Channel
Browser, it is highlighted, but the TV is not turned to the
channel until you press the ENTER button.
2
3
Press the ENTER button to tune the TV to the highlighted
item.
Press the EXIT button to close the Channel Browser.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
68
Adding and clearing channels and inputs in the History List
As a channel or input is tuned, the Channel Browser adds it to the
History List and displays it on the right side of the Channel
Browser. Previously tuned channels/inputs are shifted to the left,
eventually moving off the left side. Press the BACK CB arrow
button to surf backward through the previously tuned
channels/inputs. Any channel or input that is tuned repeatedly will
not be repeated in the History List, but instead is moved to the end
of the list on the right side of the Channel Browser.
The Channel Browser will store the following channels:
❖
All channels that are tuned using the numeric buttons on the
remote control.
❖
All channels that are tuned using the CH arrow buttons on the
remote control.
NOTE
Whenever an item is selected that cannot be tuned (for various
reasons), the TV will automatically tune to the previously viewed
channel or input.
Clearing channels from the History List:
❖
Reconfiguring the ANT/CABLE input will clear the History
List. see “ANT/CABLE IN” on page 50
❖
Turning off the TV will clear the History List.
Tuning to the next programmed channel
To tune to the next programmed channel, press the CH arrow
buttons on the remote control or TV control panel.
NOTE
This feature will not function until you have programed channels into
the TV’s channel memory, see “Storing channels in memory
(optional)” on page 51.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Tuning channels using the Channel Browser
69
Tuning to a specific channel (programmed or unprogrammed)
To tune analog channels:
Press the Channel Number (0–9) on the remote control. For
example, to select channel 125, press 1, 2, 5, and then press the
ENTER button.
Tuning digital channels:
Press the Channel Number (0–9) on the remote control, followed by
the (Dash 100) button, and then the sub-channel number. For
example, to select digital channel 125-1, press 1, 2, 5, –, 1, and then
press the ENTER button.
NOTE
If a digital channel is not programmed, either through the automatic
channel scan or the Channel add function, see “Auto Tuning” on
page 51, you will have to tune the RF channel using the Channel
Numbers and the (Dash 100) button on the remote control.
Switching between two channels using Channel Return
The Channel Return feature allows you to switch between two
channels without entering an actual channel number each time.
1
2
Select the first channel you want to view.
Select a second channel using the Channel Number buttons
(and the (Dash 100) button if selecting a digital channel).
3
Press the CH RTN button on the remote control.
The previous channel will display. Each time you press the CH
RTN button, the TV will switch back and forth between the
last two channels that were tuned.
NOTE
If you press the CH RTN button from a non-antenna input, the TV will
return to the last-viewed input.
Switching between two channels using SurfLock™
The SurfLock™ feature temporarily “memorizes” one channel to
the CH RTN button, so you can return to that channel quickly from
any other channel by pressing the CH RTN button.
To memorize a channel to the CH RTN button:
1
Tune the TV to the channel you wish to program into the CH
RTN button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the picture size
70
2
3
Press and hold the CH RTN button for a few seconds until the
message “Memorized” appears on the screen. The channel has
been programmed to the CH RTN button.
You can then change channels repeatedly, and when you press
the CH RTN button, the memorized channel will be tuned.
The TV will return to the memorized channel one time only. Once
you press the CH RTN button and then change channels again, the
CH RTN memory will be cleared and the button will function as
Channel Return, by switching back and forth between the last two
channels that are tuned.This feature also works for external inputs.
Selecting the picture size
You can view many program formats in several picture sizes—
Native, 4:3, Full, TheaterWide 1, TheaterWide 2, TheaterWide 3,
Normal, and Dot by Dot.
NOTE
The picture size illustrations are examples only. The format of the
image (in any of the picture sizes) depends on the format of the
signal you are currently watching. Select the picture size that
displays the current program in the way that looks best to you.
You can save separate picture size preferences for each input on
your TV.
To select the picture size:
1
2
Press the PIC SIZE button on the remote.
With the Picture Size menu displayed, do one of the following:
❖
❖
Repeatedly press the PIC SIZE button.
Press the corresponding number button (0-5) while the
Picture Size menu is displayed.
❖
Press the (
/
arrow) buttons while the Picture Size
menu is displayed.
NOTE
Using these functions to change the picture size (i.e., changing the
height/width ratio) for any purpose other than your private viewing
may be prohibited under the Copyright Laws of the United States and
other countries, and may subject you to civil and criminal liability.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the picture size
71
To select the picture size using the menus:
1
2
Select Picture Size in the Theater Settings menu.
Press the (
/
arrow) buttons to select the desired picture size
setting.
3
Highlight Done, and then press the ENTER button.
NOTE
Some of the picture sizes may not be available depending on the
receiving signal format (those will be grayed out in the Picture Size
screen).
NOTE
NOTE
Using these functions to change the picture size (i.e., changing
the height/width ratio) for any purpose other than your private
viewing may be prohibited under the Copyright Laws of the
and criminal liability.
If you select a TheaterWide® picture size, the top and bottom edges
of the picture (including subtitles or captions) may be hidden. To
view these edges, adjust the Picture Position or try viewing the
program in 4:3 or Full, see “Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)” on page 75.
Full
The Full 16:9 setting is for viewing in the 16:9 (480i, 480p) source
programs. If receiving a squeezed 4:3 format program, the picture is
stretched horizontally to fill the width of the screen but not
stretched vertically.
(Sample Illustration) Picture size - Full 16:9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the picture size
72
The Full setting is for viewing in 1080i, 1080p, and 720p program
source.
(Sample Illustration) Picture size - Full
The edges of the picture may be hidden.
TheaterWide 1
This setting is for viewing in 4:3 format programs.
(Sample Illustration) Picture size - TheaterWide 1
The center of the picture remains close to its original proportion,
but the left and right edges are stretched horizontally to fill the
screen.
TheaterWide 2
This setting is for viewing letter box programs.
(Sample Illustration) Picture size - TheaterWide 2, letter box
The picture’s top and bottom edges may be hidden*.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the picture size
73
TheaterWide 3
This setting is for viewing letter box programs with subtitles.
(Sample Illustration) Picture size - TheaterWide 3, letter box with
subtitles
The picture’s top and bottom edges are hidden*.
* To view the hidden areas (such as subtitles or captions), see
“Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)”
on page 75.
Native
These settings are for viewing in 480i (HDMI®), 480p (HDMI®),
720p, 1080i, and 1080p signal programs).
(Sample Illustration) Picture size - Native
❖
If receiving a 1080i, 1080p, 720p, 480i (HDMI®), or 480p
(HDMI®) signal program, the video is scaled to display the
entire picture within the borders of the screen (i.e. no
over-scanning).
❖
This is especially useful for external HD sources such as DVD
movies, Video Games, or computer graphics.
NOTE
❖ The Native mode is supported only for HDMI® (1080i, 1080p,
720p, 480i, and 480p), ColorStream® (1080i and 720p), and
ANT/CABLE (digital) inputs (1080i, 1080p, and 720p).
❖ Depending on the input signal, the picture’s border may be
hidden, displayed in black, or noisy.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the picture size
74
4:3
(Sample Illustration) Picture size - 4:3
Some program formats will display with sidebars and/or bars at the
top and bottom.
Normal
This setting is for viewing VGA, SVGA, XGA, WXGA, and
SXGA sources.
(Sample Illustration) Picture size - Normal
This size is a non-stretched display. Some input signal formats will
display with sidebars and/or bars at the top and bottom.
Dot by Dot
This setting is for viewing VGA, SVGA, XGA, WXGA, and
SXGA sources.
(Sample Illustration) Picture size - Dot by Dot
Dot by Dot is a non-scaling display. Depending on the input signal
format (VGA, for example) the picture may appear with sidebars
and/or bars at the top and bottom.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)
75
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)
You can set separate scroll settings for the TheaterWide 2 and
TheaterWide 3 modes for each input.
To set the scroll settings:
1
2
Press the MENU button and open the Picture menu.
Highlight Theater Settings, and then press the ENTER
button.
(Sample Image) Picture menu - Theater Settings selection
3
In the Picture Size field, select either TheaterWide 1,
TheaterWide 2, or TheaterWide 3
NOTE
You cannot scroll in any other mode.
4
5
Press the ( arrow) button to select the Picture Scroll field.
Press the ( arrow) buttons to scroll the picture up and
down as needed.
/
6
To save the new settings, highlight Done, and then press the
ENTER button.
To revert to the factory defaults, highlight Reset and then press
the ENTER button.
The adjustment range is from -5 to +10.
NOTE
When receiving a signal at 480i resolution, the picture scroll function
may have limited adjustment range.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Auto Aspect feature
76
Using the Auto Aspect feature
When this feature is set to On, the TV will automatically select the
picture size when one of the following input sources is received:
❖
A 480i, 480p, 720p, 1080i digital signal from the
ANT/CABLE input
❖
❖
A 480i signal from the ColorStream® HD or Video input
480i, 480p, 720p, 1080i, 1080p, or VGA (60Hz) signal from
the HDMI 1, HDMI 2, or HDMI 4 input.
Aspect Ratio of
Signal Source
Aspect is On)
4:3 Normal
4:3 Letter Box
16:9 Full
4:3
TheaterWide 2
Full
Not defined (no ID-1
data or HDMI® aspect
data)
The current picture size you selected, see “Selecting the picture
size” on page 70.
NOTE
The auto aspect ratio feature is not applicable to the PC input.
To turn on the auto aspect ratio feature:
1
2
Press the MENU button and open the Picture menu.
Highlight Theater Settings, and then press the ENTER
button.
3
4
In the Auto Aspect Ratio field, select On.
To save the new settings, highlight Done, and then press the
ENTER button.
To revert to the factory defaults, highlight Reset and then press
the ENTER button.
To turn off the Auto Aspect ratio feature, Select Off in step 3 above.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Selecting the cinema mode
77
Selecting the cinema mode
When you view a DVD (3:2 pulldown processed) from a DVD
player connected to the VIDEO, ColorStream® HD (component
video), or HDMI® inputs on the TV, smoother motion can be
obtained by setting the Cinema Mode to Film.
To set the Cinema Mode to Film:
(available for 480i and 1080i signals)
1
2
3
Press the MENU button and open the Picture menu.
Highlight Picture Settings, and then press the ENTER button.
Highlight Advanced Picture Settings, and then press the
ENTER button.
4
5
In the Cinema Mode field, select Film.
To save the new settings, highlight Done and press the ENTER
button.
To revert to the factory defaults, highlight Reset and press the
ENTER button.
To set the Cinema Mode to Video, select Video in step 3 above.
Using the FREEZE feature
To use the FREEZE feature:
1
2
When watching the TV, press the FREEZE button to freeze
the picture.
To unfreeze the picture, press the FREEZE button again
(or any other button).
NOTE
Using the FREEZE function for any purpose other than your private
viewing may be prohibited under the Copyright Laws of the United
States and other countries, and may subject you to civil and criminal
liability.
NOTE
If the TV is left in FREEZE mode for more than 15 minutes, the
FREEZE mode will automatically release and the TV returns to normal
video.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the picture
78
Adjusting the picture
Selecting the picture mode
You can select your desired picture settings from the modes
described below.
Mode:
Dynamic
Standard
Movie
Description:
Bright and dynamic picture (factory setting)
Standard picture settings (factory setting)
Lower contrast for darkened room (factory setting)
Designed for viewing of PC tables and documents
Your personal preferences
PC
Preference
NOTE
PC mode is available for HDMI® and PC inputs only (grayed out for
other input sources).
To select the picture mode using the menu system:
1
Press the MENU button and open the Picture menu.
2
Highlight Mode, and then press the ENTER button.
(Sample Image) Picture menu - Mode selection
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the picture
79
3
Press the (
/
arrow) buttons to select the picture mode you
prefer, and then press the ENTER button.
(Sample Image) Mode selections screen
Adjusting the picture quality
You can adjust the picture quality (Contrast, Backlight,
DynaLight™, Brightness, Color, Tint, and Sharpness.) to your
personal preferences.
Selection
Contrast
Backlight*
DynaLight™**
Brightness
Color
Pressing ( )
lower
Pressing ( )
higher
darker
lighter
On/Off
darker
On/Off
lighter
paler
deeper
Tint
reddish
softer
greenish
sharper
Sharpness
* Backlight: adjusts the brightness of the entire screen. When in video mode
and no signal is input, this selection is automatically set to 0. (Settings are
stored in memory.)
**DynaLight™: Automatically strengthens the black coloring of dark areas
in the video according to the level of darkness.
To adjust the picture quality:
1
2
Press the MENU button and open the Picture menu.
Highlight Picture Settings, and then press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
80
3
4
Press the (
/
arrow) buttons to select the picture quality you
wish to adjust (Contrast, Backlight, DynaLight, Brightness,
Color, Tint, or Sharpness), and then press the (
buttons to adjust the setting.
/
arrow)
ENTER button. You can use any of the picture modes (see
“Selecting the picture mode” on page 78) as a starting point for
adjusting the picture settings.
To revert back to the base mode that you began adjusting the
picture settings from, highlight Reset, and then press the
ENTER button.
The picture qualities you adjusted are automatically saved in the
Preference mode, see “Selecting the picture mode” on page 78 until
Reset is selected.
Using closed captions
Base closed captions
Closed caption mode has two options:
❖
Captions—An onscreen display of the dialogue, narration and
sound effects of TV programs and videos that are closed
captioned (usually marked “CC” in program guides).
❖
Text—An onscreen display of information not related to the
current program, such as weather or stock data (when provided
by individual stations).
To view captions or text:
1
Press the MENU button and open the Preferences menu, and
then highlight Base CC Mode.
2
Press the (
/
arrow) buttons to select the desired closed
caption mode, and then press the EXIT button.
To view captions, highlight CC1, CC2, CC3, or CC4.
(CC1 displays translation of the primary language in your area.)
(Sample Illustration) Viewing captions
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using closed captions
81
NOTE
If the program or video you selected is not closed captioned, no
captions will display onscreen.
To view text, highlight T1, T2, T3, or T4.
(Sample Illustration) Captions - text
NOTE
If text is not available in your area, a black rectangle may appear on
screen. If this happens, set the Base CC Mode to Off.
To turn off closed caption mode, select Off in step 2 above.
NOTE
A closed caption signal may not display in the following situations:
❖ When a recording has been dubbed
❖ When the signal reception is weak
❖ When the signal reception is non-standard
Digital CC settings
You can customize the closed caption display characteristics by
changing the background color, opacity, text size, type, edge, and
color.
NOTE
❖ These settings are available for digital channels only.
❖ You cannot set Caption Text and Background as the same color.
To customize closed captions:
1
2
Press the MENU button and open the Preferences menu.
Highlight Digital CC Settings, and then press the ENTER
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using closed captions
82
3
4
Press the (
/
arrow) buttons to highlight the characteristic
you wish to change, and then press the (
/
arrow) buttons to
select the format for that characteristic.
To save the new settings, highlight Done, and then press the
ENTER button.
To revert to the factory defaults, highlight Reset, and then
press the ENTER button.
Mode:
Description
Caption size
Auto, Small, Standard, Large
Caption text type
Auto, Default, Mono (with Serif), Prop. (with Serif), Mono
(without Serif), Prop. (without Serif), Casual, Cursive, Small
Capitals
Caption text edge
Caption text color
Auto, None, Raised, Depressed, Uniform, Left Drop Shadow,
Right Drop shadow
Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan
Text foreground opacity Auto, Transparent, Translucent, Flashing, Solid
Background color Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan
Text background opacity Auto, Transparent, Translucent, Flashing, Solid
Caption text edge color Auto, Black, White, Red, Green, Blue, Yellow, Magenta, Cyan
CC Selector
You can use the CC Selector to temporarily override the default
analog caption mode (set in Base CC Mode) for a particular
channel. However, once you change to any other channel, the
closed caption setting will automatically change back to the current
Base CC Mode setting.
You can also use the CC Selector to select digital closed caption
services, if available. When such services are not available, the CC
Selector presents a default list of services. If the selected service is
not available, the next best service will be used.
To select closed captions:
1
2
3
Press the MENU button and open the Preferences menu.
Highlight CC Selector, and then press the ENTER button.
Press the (
/
arrow) buttons to select Closed Caption, and
arrow) buttons to select the desired
then press the (
/
service.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the audio
83
4
5
To save the new settings, highlight Done, and then press the
ENTER button.
Press the EXIT button.
Adjusting the audio
Muting the sound
Press the MUTE button to partially reduce (1/2 Mute) or turn off
(Mute) the sound. Each time you press the MUTE button, the mute
mode changes in the following order: 1/2 Mute, Mute, Volume, 1/2
Mute, etc.
(Sample Image) Levels of mute
If closed caption mode is set to Off when you select MUTE mode,
the closed caption feature becomes active if the TV program is
closed captioned. To mute the audio without activating the closed
captioning, press the VOL (–) button to set the volume to 0.
For more information, see “Using closed captions” on page 80.
NOTE
If you modify items in the SOUND menu while Mute is active, Mute
is cancelled.
Using the digital audio selector
You can use the Digital Audio Selector to conveniently switch
between audio tracks on a digital channel (for those channels that
have multiple audio tracks). This temporarily overrides the audio
track chosen by the language option under Audio Setup, see
“Selecting stereo/SAP broadcasts” on page 84.
1
Press the MENU button and open the Sound menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the audio
84
2
Highlight Digital Audio Selector, and then press the ENTER
button.
(Sample Image) Sound menu - Digital Audio Selector selection
3
4
Press the (
the (
/
arrow) buttons to select Audio, and then press
/
arrow) buttons to select the desired service.
Press the EXIT button.
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature allows you to output
high-fidelity stereo sound. MTS also can transmit a second audio
program (SAP) containing a second language, music or other audio
information (when provided by individual stations).
When the TV receives a stereo or SAP broadcast, an icon or word
“SAP” appears when the INFO button is pressed. The MTS feature
is only available for analog signals on the ANT/CABLE input.
To listen in stereo sound:
1
2
3
4
Press the MENU button and open the Sound menu.
Highlight Audio Setup, and then press the ENTER button.
In the MTS field, select Stereo.
To save the new settings, highlight Done, and then press the
ENTER button.
To reset the settings to the factory defaults, highlight Reset,
and then press the ENTER button.
NOTE
❖ You can typically leave the TV in Stereo mode because it outputs
the type of sound being broadcast (stereo or monaural).
❖ If the sound is noisy, select Mono to reduce the noise.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the audio
85
To listen to an alternate language on an ATSC digital station (if
available), highlight the Language field in step 3 above, and then
press the (
/
arrow) buttons to select the language you prefer.
To listen to a second audio program on an analog station, if
available, select SAP in step 3 above.
NOTE
❖ A second audio program (SAP) can be heard only on those TV
stations that offer it. For example, a station might broadcast
another language as a second audio program. If you have SAP
on, you will see the current program on the screen but hear the
other language instead of the program’s normal audio.
❖ If you have SAP on and the station you are watching is not
broadcasting a second audio program, the station’s normal
audio will be output. However, occasionally there is no sound at
all in SAP mode. If this happens, set the MTS feature to Stereo
mode.
Adjusting the audio quality
You can adjust the audio quality by adjusting the bass, treble and
balance.
To adjust the audio quality:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Settings, and then press the ENTER button.
Press the (
/
arrow) buttons to highlight the item you wish
to adjust (Bass, Treble, or Balance).
4
5
Press the ( arrow) buttons to adjust the level.
/
❖
makes the bass or treble weaker or increases the balance
in the left channel (depending on the item selected).
❖
makes the bass or treble stronger or increases the
balance in the right channel (depending on the item
selected).
To save the new settings, highlight Done, and then press the
ENTER button.
To reset the settings to the factory defaults, highlight Reset,
and then press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Adjusting the audio
86
Audyssey ABX™
Audyssey ABX™ technology uses sophisticated driver analysis and
low frequency monitoring to extend the range and bass of small
speakers.
To turn on Audyssey ABX™:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Settings, and the press the ENTER button.
Press the (
/
arrow) buttons to highlight the Audyssey
ABX™ field.
4
Press the (
/
arrow) buttons to select On.
Using Dynamic Volume (Audyssey Dynamic Volume®)
This feature provides a consistent sound volume between television
programs, commercials, and between the loud and soft passages of
movies.
To turn on Dynamic Volume:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Settings, and then press the ENTER button.
Press the (
field.
/
arrow) buttons to highlight Dynamic Volume
4
Press the (
/
When you use ColorStream® HD or Video, switch the AV input
mode appropriately.
Selecting the optical audio output format
You can select the optical audio output format when you connect a
Dolby® Digital decoder or other digital audio systems to the TV’s
Optical Audio Out terminal (see “Connecting a digital audio
system” on page 33).
To select the optical audio output format:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Setup, and then press the ENTER button.
In the Optical Output Format field, select either Dolby
Digital or PCM, depending on your device.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Locks menu
87
4
To save the new settings, highlight Done, and then press the
ENTER button.
To reset the settings to the factory defaults, highlight Reset,
and then press the ENTER button.
Using the Dolby® Digital Dynamic Range Control feature
You can further compress Dolby Digital dynamic range, allowing
you to switch from digital to analog broadcasts at the same dynamic
range.
To use the Dolby Digital Dynamic Range Control:
1
2
3
Press the MENU button and open the Sound menu.
Highlight Audio Setup, and then press the ENTER button.
In the Dolby Digital Dynamic Range Control field, select
either Compressed or Standard. When Standard is selected,
the audio outputs with minimal compression.
4
To save the new settings, highlight Done, and then press the
ENTER button.
To reset the settings to the factory defaults, highlight Reset,
and then press the ENTER button.
NOTE
❖ This feature is available when the TV is tuned to a digital RF
channel with the Dolby Digital signal.
❖ The Dolby Digital Dynamic Range Control will function in
relation to Optical Output Format (PCM mode).
Using the Locks menu
The Locks menu includes the Enable Rating Blocking, Edit Rating
Limits, Input Lock, Panel Lock, GameTimer and New PIN Code
features. You can use these features after entering the correct PIN
code.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Locks menu
88
Entering the PIN code
1
Press the MENU button and highlight the Locks menu icon.
(Sample Image) Locks menu screen
2
Press the ( arrow) button to display the PIN code entry
screen.
The Lock System screen appears if a PIN code has not been
stored.
(Sample Image) Lock system - store PIN screen
❖
Press the Channel Number buttons to enter a new four-
digit code, enter the code a second time to confirm, and
then press the ENTER button.
The Locks/Active screen appears if the PIN code is already
stored.
❖
Use the Number buttons to enter your four-digit code, and
then press the ENTER button.
If the wrong PIN code is entered, the message “Incorrect PIN
code, please try again!” appears.
❖
❖
Highlight Retry, and then press the ENTER button.
Enter the code again, and then press the ENTER button.
When the correct PIN code is entered, the Locks menu opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
89
NOTE
The PIN code cannot be set to “0000.”
Forgotten PIN code
While the PIN code entering screen is displayed, press the INFO
button four times within five seconds. The PIN code will be cleared
and you can enter a new PIN code.
Changing or deleting your PIN code
1
Press the MENU button and highlight the Locks menu icon.
2
Press the ( arrow) button to display the PIN code entering
screen.
3
4
5
6
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight New PIN Code, and
then press the ENTER button.
Press the Number buttons to enter a new four-digit code.
Reenter the PIN code to confirm it.
Press the ENTER button.
The new PIN code is now active.
NOTE
The PIN code cannot be set to “0000.”
Using parental controls (for USA region)
Blocking TV programs and movies by rating (V-Chip)
Some TV programs and movies include signals that classify the
content of the program (as unsuitable for younger viewers). The
V-Chip feature in this TV detects the signals and blocks the
programs according to the ratings you select.
1
2
Press the MENU button and highlight the Locks menu icon.
Press the ( arrow) button to display the PIN code entering
screen.
3
4
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight Enable Rating
Blocking.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
90
5
Press the ( arrow) button to select On, and then press the
ENTER button.
(Sample Image) Locks menu - Enable Rating Blocking selection
6
Press the ( arrow) button to highlight Edit Rating Limits,
and then press the ENTER button.
The Edit Rating Limits screen appears.
7
For each desired selection, press the (
/
/
/
arrow)
buttons to highlight the selection, and then press the ENTER
button to select it.
A box with an “X” is a rating that will be blocked. As you
highlight a rating, a definition for the rating appears at the
bottom of the screen.
8
To save the new settings, highlight Done, and then press the
ENTER button.
NOTE
The above blocking level selection is for the U.S V-Chip system. For
the Canadian Rating menu, highlight “Canada RS,” and then press
the ENTER button.
Downloading an additional rating system
In the future, an additional rating system may become available for
use in selectively blocking TV programs and movies.
NOTE
The currently tuned station must be receiving a digital signal before
an additional rating system can be downloaded.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
91
To download the additional rating system, if available:
1
2
Press the MENU button and highlight the Locks menu icon.
Press the ( arrow) button to display the PIN code entering
screen.
3
4
5
6
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight Enable Rating
Blocking.
Press the ( arrow) button to select On, and then press the
ENTER button.
Press the ( arrow) button to highlight Edit Rating Limits,
and then press the ENTER button.
The Edit Rating Limits screen appears.
7
Highlight Alt RS, and then press the ENTER button.
The Edit Alternate Ratings screen appears.
NOTE
❖ The Alt RS button will only be available if an additional rating
system is currently available.
❖ It may take several minutes for the TV to download the additional
rating system.
❖ The information displayed in the Alternate Ratings screen will
depend on the configuration of the additional rating system
available at the time of download.
8
9
For each desired selection, press the (
/
/
/
arrow)
buttons to highlight the selection, and then press the ENTER
button to select it.
A box with an “X” is a rating that will be blocked.
To save the new settings, highlight Done, and then press the
ENTER button.
10 In the Edit Rating Limits screen, highlight Done, and then
press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
92
NOTE
❖ The additional rating system can only be downloaded one time.
You will not be able to download any updates to the rating
system should such updates become available.
❖ The additional rating system is not designed, transmitted or
controlled by the TV or Toshiba, nor is the availability of an
additional rating system determined or controlled by Toshiba.
Similarly, the rating of programs in an additional rating system is
not determined, transmitted or controlled by the TV or Toshiba.
❖ The additional rating system is an evolving technology;
therefore, availability, content and format may vary.
Rating system
Independent rating system for broadcasters:
Ratings:
Description and Content themes:
TV-MA
Mature Audience Only (This program is specifically designed to be viewed
by adults and therefore may be unsuitable for children under 17.
L) Crude or indecent language
S) Explicit sexual activity
V) Graphic violence
TV-14
TV-PG
TV-G
Parents Strongly Cautioned (This program contains some material that
many parents would find unsuitable for children under 14 years of age.)
D) Intensely suggestive dialogue
L) Strong, coarse language
S) Intense sexual situations
V) Intense violence
Parental Guidance Suggested (This program contains material parents may
find unsuitable for younger children.)
D) Some suggestive dialogue
L) Infrequent coarse language
S) Some sexual situations
V) Moderate violence
General Audience (Most parents would find this program suitable for all
ages)
TV-Y7,
TV-Y7FV
Directed to Older Children (This program is designed for children age 7 and
above.
NOTE: Programs in which fantasy violence may be more intense or more
combative than other programs in this category are designated TV-Y7FV.)
TV-Y
All Children (This program is designed to be appropriate for all children)
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
93
Independent rating system for movies:
Ratings:
X
Description and Content themes:
X-rated (For adults only)
NC-17
R
Not intended for anyone 17 and under
Restricted (Under 17 requires accompanying parent or adult)
PG-13
Parents Strongly Cautioned (Some material may be inappropriate for
children under 13)
PG
G
Parents Guidance Suggested (Some material may be not be suitable for
children)
General Audience (Appropriate for all ages)
Indication other than rating system:
Display:
Description:
NONE
The program is rated None.
(No rating appears) No rating information is provided.
NOTE
If you place an “X” in the box next to “None” Rated, programs rated
“None” or “Not Rated” will be blocked; Programs that do not provide
any rating information will not be blocked.
Displaying ratings
To display the rating of the program you are watching, press the
INFO button on the remote control. If it is rated “None” the word
“NONE” appears in the INFO screen. If rating information is not
provided, no rating will appear in the INFO screen.
(Sample Image) Rating Info screens
Blocking TV programs by Canada rating
1
Press the MENU button and highlight the Locks menu icon.
2
Press the ( arrow) button to display the PIN code entering
screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using parental controls (for USA region)
94
3
4
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight Enable Rating
Blocking.
5
6
Press the ( arrow) button to select On.
Press the ( arrow) button to highlight Edit Rating Limits,
and then press the ENTER button.
The Edit Rating Limits screen appears.
7
8
Highlight Canada RS, and then press the ENTER button.
The Canadian Rating Menu screen appears.
Press the (
/
/
/
arrow) buttons, and then press the
ENTER button to select the level of blocking you prefer.
A box with an “X” is a rating that will be blocked.
9
To save the new settings, highlight Done, and then press the
ENTER button.
10 In the Edit Rating Limits screen, highlight Done, and then
press the ENTER button.
Rating system for programs in English:
Ratings:
E
Description and Content themes:
Exempt shows
C
C8+
G
Children ages of 2 to 7 years
Children ages of 8 years and older
General programming
PG
14+
Parental Guidance
Viewers 14 and older
Adult programming
18+
Rating system for programs in English:
Ratings:
E
Description and Content themes:
Exempt shows
G
General programming
8 ans+
13 ans+
16 ans+
18 ans+
Not recommended for ages under 8
Not recommended for ages under 13
Not recommended for ages under 16
Programming restricted to adults
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the input lock feature
95
Unlocking programs temporarily
If you try to tune to a program that exceeds the rating limits you
have set, the TV will enter program lock mode and a warning
message appears on the screen.
(Sample Illustration) Warning - exceeded rating limit
You can either temporarily unlock the program or select an
unlocked program to watch.
To temporarily unlock the program:
1
2
Press the MUTE button.
Enter your four-digit PIN code, and then press the ENTER
button.
If the correct code is entered, the program lock mode is
released and the normal picture appears. All locking will be
enabled again when you change the channel.
Using the input lock feature
You can use the Input Lock feature to lock the video inputs (Video,
ColorStream® HD, HDMI 1, HDMI 2, HDMI 3, and PC) and
channels 3 and 4. You will not be able to view the input sources or
channels until you unlock the inputs.
To lock/unlock the video inputs:
1
2
3
From the Locks menu, press the ( arrow) button to display
the PIN code entering screen.
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight Input Lock, and then
press the ( arrow) button to select the level of video input
locking you prefer (see table below for descriptions).
4
Press the EXIT button.
Mode:
Video
Video+
Description:
Locks Video, ColorStream® HD, HDMI 1, HDMI 2, HDMI 3, and PC.
Locks Video, ColorStream® HD, HDMI 1, HDMI 2, HDMI 3, PC and
channels 3 and 4. Select Video+ if you play video tapes via an ANT/CABLE
input.
Off
Unlocks all video inputs and channels 3 and 4.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Locking channels
96
Locking channels
With the Lock feature, you can lock specific channels. Locked
channels can only be accessed by entering the PIN code, see
“Entering the PIN code” on page 88.
To lock channels:
1
From the Setup menu, highlight Installation, and then press
the ENTER button.
2
3
Press the ENTER button to select Terrestrial.
Press the (
/
arrow) buttons to select Channel Options, and
then press the ENTER button.
The list of channels appears.
(Sample Illustration) Channel options
4
5
Press the ( arrow) button, and then press the (
/
arrow)
buttons to select a channel in the lock column.
Press the ENTER button.
PIN code entry will be required to set a locked channel.
NOTE
If the PIN code has not yet been set, a warning message appears.
6
7
8
A check appears in the box.
To remove the check, press the ENTER button.
Press the EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
97
Locking channels
Using the GameTimer®
You can use the GameTimer® to set a time limit for playing a video
game (30–120 minutes). When the GameTimer® expires, the TV
enters Input Lock mode and locks out the input source for the video
game device.
To set the GameTimer®:
1
2
3
From the Locks menu, press the ( arrow) button to display
the PIN code entering screen.
button.
Press the ( arrow) button to highlight GameTimer, and press
the ( arrow) button to until the desired Input Lock is activated
(30, 60, 90 or 120 minutes).
To cancel the GameTimer®, select Off in step 3 above.
To deactivate the Input Lock once the GameTimer® has activated it:
❖
page 95.
NOTE
❖ A message appears when 10 minutes, 3 minutes, and 1 minute
are remaining.
❖ If the TV loses power with time remaining, the TV will enter Input
Lock mode when power is restored (as if the GameTimer had
been activated). To resume use, you must deactivate the Input
Lock, see “Using the input lock feature” on page 95
Using the panel lock feature
You can lock the control panel to prevent your settings from being
changed accidentally (by children, for example). When Panel Lock
is set to On, none of the controls on the control panel operate
except POWER.
To lock the control panel:
1
2
Press the MENU button and highlight the Locks menu.
Press the ( arrow) button to display the PIN code entering
screen.
3
4
Enter your four-digit PIN code, and then press the ENTER
button.
Press the ( arrow) button to highlight Panel Lock.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the PC settings feature
98
5
Press the ( arrow) button to select On.
When the control panel is locked and any button on the control
panel (except POWER) is pressed, the message “NOT
AVAILABLE” appears.
HDMI-CEC Setup
00:00
(Sample Illustration) Locks menu - Panel Lock selection
To unlock the control panel, select Off in Step 5 in this section or
press and hold the VOLUME (–) button on the TV control panel
for approximately 15 seconds until the volume icon appears.
Using the PC settings feature
connected to the TV's PC IN terminal, you can use the PC Settings
feature to make adjustments to the image. If the edges of the picture
are cut off, readjust the Horizontal Position and Vertical Position. If
the picture is affected by interference, readjust the Clock Phase and
Sampling Clock.
To adjust the PC settings:
1
Repeatedly press the INPUT button to select PC Input mode,
see “Selecting the video input source” on page 59.
2
3
Press the MENU button and open the Setup menu.
Press the (
/
arrow) buttons to select PC Settings, and then
press the ENTER button.
HDMI-CEC Setup
00:00
(Sample Image) Setup menu - PC Settings selection
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the PC settings feature
99
NOTE
If a computer is not connected or there is no PC input signal, this
feature will be grayed out in the Setup menu.
4
5
Press the (
/
/
arrow) buttons to select an item.
Press the (
adjustments.
arrow) buttons to make the appropriate
(Sample Image) PC Settings - adjustments screen
NOTE
The screen is disrupted momentarily while adjusting the PC settings.
This is not a sign of malfunction.
Mode:
Description:
Horizontal Position Moves the picture left/right. The adjustment range is within 10 from
center.*
Vertical Position
Clock Phase
Sampling Clocks
Reset
Moves the picture up/down. The adjustment range is within 10 from
center.*
Helps to reduce noise and sharpen the picture. The adjustment range is
within 16 from center.*
Helps to reduce noise and minimize periodic vertical stripes on the
screen. The adjustment range is within 10 from center.*
Highlight this item, and then press the ENTER button to get an
* The default settings and/or adjustment ranges may vary depending on the
input signal format.
Setting the PC Audio
You can output or mute sound from your computer when
connecting it to your TV using the PC IN terminal and an analog
RGB cable, see “Connecting a computer to the TV’s PC IN
terminal” on page 35.
To set the PC Audio:
1
Press the MENU button and open the Sound menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
100
2
3
Highlight Audio Setup, and then press the ENTER button.
Press the (
/
/
arrow) buttons to select PC Audio, and then
arrow) buttons to select No or Yes.
press the (
❖
❖
Yes: When viewing the PC input, the audio from the PC
Audio input can be heard.
No: When viewing the PC input, there will be no audio.
NOTE
Because the PC and HDMI 1 inputs share the same set of analog
audio inputs, the PC Audio menu setting influences the HDMI 1
Audio menu setting. If PC Audio is set to “No” the HDMI 1 Audio
setting changes to “Auto.” If PC Audio is set to “Yes” the HDMI 1
Audio setting is set to “Digital” and is grayed out in the menu. (See
also “Setting the HDMI® audio mode” on page 55)
Using the Media Player
Using Media Player with a USB device
You can enjoy photos or music contents stored on a USB storage
device.
Photo Viewer specifications:
❖
❖
❖
❖
❖
Data type: JPEG EXIF ver 2.1
File format: JPEG
Maximum photo size: 6 MB
Maximum number of files: 500/folder
Maximum photo resolution:
4096 x 4096 pixels
Music Player specifications:
❖
❖
File format: MP3
Sampling frequency: 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1
kHz, 48 kHz
❖
❖
Bit rate: from 8 to 320 kbps
Maximum number of files: 500/folder
Supported file system: FAT16 and FAT32
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
101
NOTE
❖ Gently insert the USB device into the port and do not remove
while viewing Media Player.
❖ USB device: USB Mass Storage Class device (MSC)
❖ Connectivity is not guaranteed for all devices.
❖ Connect the USB device to the TV directly.
❖ Do not use a USB Hub.
❖ You must obtain any required permission from copyright owners
to use copyright content. Toshiba cannot and does not grant
such permission.
❖ Depending on the file size and amount in your USB storage
device, it may take some time to load before content is viewable.
A message will display on-screen when files are loading from
the USB storage device.
❖ Only limited types of U3 USB device are supported. Therefore, it
is suggested that you not use U3 USB with Media Player.
❖ Non-supported characters will be replaced with a square.
Auto Start function
When Auto Start is enabled, you will be asked if you want to start
the Media Player when a USB device is inserted. If Auto Start is
disabled, you must manually start the Media Player from the menu.
To change the Auto Start setting:
1
2
Press the MENU button and open the Setup menu.
Press the ( arrow) button to select Media Player, and then
press the ENTER button.
3
4
Press the (
/
/
arrow) buttons to highlight Auto Start.
Press the (
arrow) buttons to select On or Off.
To open the Media Player
There are two methods for starting the Media Player: auto start and
manual start.
Auto Start:
1
Gently insert a supported USB storage device to the USB port
on the back of the TV. A prompt will appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
102
NOTE
If you repeatedly insert and remove the USB connector, the prompt
may not appear.
2
Press the (
/
arrow) buttons to select Yes, and then press the
ENTER button.
The Media Player menu appears. (If you select No, nothing
happens.)
(Sample Image) Media Player - open screen
NOTE
❖ The prompt will disappear after about 10 sec.
❖ If Auto Start is set to off, you can start the Media Player
manually.
Manual Start:
1
2
Press the MENU button and open the Setup menu.
Press the ( arrow) button to select Media Player, and then
press the ENTER button.
3
Press the (
/
arrow) buttons to highlight Photo or Music,
and then press the ENTER button.
(Sample Image) Media Play screen
NOTE
❖ The viewer will open even if there are no photo or music files.
❖ While the Media Player is active, the main menus cannot be
displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
103
Viewing photo files
There are three types of view modes, multi view, single view, and
slide show.
Multi View
This view allows you to search for photos in a grid format. These
pictures are displayed using thumbnail data in each image file.
(Sample Image) Media Play - photos screen
To use multi view:
1
Press the (
/
/
/
arrow) buttons to move the highlight in
one window. If all of the photos will not fit in one screen, the
screen will move to the previous page when you press from
the top left thumbnail. When you press from the bottom
right thumbnail, the screen will move to the next page. You can
also use the CH Up/CH down buttons to page up or down the
in photo list when there are more photos than will fit on one
screen.
2
3
When you select a folder, press the ENTER button to move to
the next layer, or press the CH RTN button to return to the
previous layer.
Press the ENTER button to view the selected photo in Single
View mode.
Single view
In this view mode, only files located in the selected directory will
be displayed. This view allows you to change the photo content
manually. When you move from Multi View to the Single View, the
currently selected photo is displayed.
To use single view:
❖
Press the ( arrow) button to view the next photo. Press to
view the previous photo.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
104
❖
Press to rotate the image 90° counterclockwise. Press to
rotate the image 90° clockwise.
Slide show
This view allows you to watch a slide show of the photos. In this
mode, only files located in the selected directory will be played.
To use slide show:
1
2
Press the ENTER button in the Single View mode.
Press the (
photo.
/
arrow) buttons to view the previous or next
To set Interval Time and Repeat settings:
1
2
Press the MENU button to open the Quick Menu.
Press the (
/
arrow) buttons to select either Interval Time
or Repeat.
3
Press the (
the CH RTN button.
/
arrow) buttons to adjust the setting and press
NOTE
Zoom and Picture size functions are disable.
To close the Photo Viewer, press the EXIT button. The television
will return to the last viewed channel or external input.
Playing music files
You can listen to music from a list of available files.
(Sample Image) Media Play - music list
1
After opening Media Player and selecting Music (see “To open
the Media Player” on page 101) press the ( arrow) buttons
/
to select a file or folder. You can use the CH Up/CH Down
buttons to page up or down the music list when there are more
files than will fit onto one screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
105
2
Select the desired folder and press the ENTER button to move
to the next layer. Press the CH RTN button to move back to the
previous layer.
3
4
With the desired file selected, press the ENTER button or the
PLAY button to start playback.
Press the STOP button to stop playback
NOTE
❖ If playback finishes before STOP is pressed, the next file will
automatically start to play from the beginning.
❖ Depending on the file size, it may take some time for playback to
begin.
During playback you can do the following:
❖
❖
❖
Press PAUSE to pause.
To resume normal playback, press PLAY.
To locate a specific file, press the SKIP Reverse or SKIP
Forward button repeatedly.
❖
To adjust volume, press the VOL (+ –) buttons.
NOTE
During playback, you can adjust the SOUND menu functions from
the Quick Menu.
To set the repeat mode:
1
2
3
4
Press the MENU button to open the Quick Menu.
Press the (
Press the (
/
arrow) buttons to select Repeat.
/
arrow) buttons to select Off, All or 1.
Press CH RETURN.
To close the Music Player, press EXIT.
Viewing photo files and playing music files at the same time
While viewing photo files, you can listen to music from a list of
available files.
1
While viewing photos in the Single View or Slide Show mode,
press MENU to open the Quick Menu.
2
Highlight Background Music and press the ENTER button.
The music list appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using the Media Player
106
3
4
Select a music file and press the ENTER button to start
playback.
Press CH RETURN twice to move back to photo view mode.
The music is now playing in the background.
Sorting photo or music files
From the photos Multi View or from the music list, you can sort
your photo or music folders and files.
To sort photo or music folders and files:
1
From photo Multi View mode or from the music list, press the
MENU button to open the Quick Menu.
2
3
Press the (
/
arrow) buttons to select Sort.
Press the (
set the sorting rule.
/
arrow) buttons to select Title, New, or Old to
Title-File sorting rules:
❖
❖
Unicode priority
Numerical (0-9), Uppercase (A-Z), lowercase (a-z),
Chinese
❖
Increasing order
New-From new to old according to the date and time when the
picture was taken.
Old-From old to new according to the date and time when the
picture was taken.
Contents
Description
Description
Photo
Photo list (Multi View)
Single View mode
See page 103
Slide Show mode
Skip to previous/next photo
Slide Show Repeat play
Slide Show Interval Time selection
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Setting the sleep timer
107
Contents
Music
Description
Music list (Multi View)
Playback
Description
See page 104
Pause
Stop
Skip
Repeat play
Sound Settings
(Adjusting the audio quality)
NOTE
During playback, you can adjust the SOUND menu functions from
the Quick Menu.
NOTE
Sorting, Total Time display may not be available in all cases.
Setting the sleep timer
You can set the sleep timer to turn off the TV after a set length of
time (maximum of 12 hours).
To set the sleep timer using the remote control:
1
Press the SLEEP button on the remote control to set the length
of time until the TV turns off.
2
Repeatedly press the SLEEP button to increase the time in
10-minute increments, or press the (
/
arrow) buttons to
increase or decrease the time in 10-minute increments, to a
maximum of 12 hours.
To set the sleep timer using the on-screen menus:
1
2
3
Press the MENU button and open the Setup menu.
Highlight Sleep Timer and press the ENTER button.
Press the Number buttons to enter the length of time
(maximum of 12 hours) and then press the ENTER button.
Or press the (
minute increments (maximum of 12 hours).
/
arrow) buttons to increase or decrease in 10-
NOTE
If a power failure occurs, the sleep timer setting may be cleared.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Automatic Power Down
108
To display the time remaining until the TV turns off, press the
SLEEP button.
To cancel the sleep timer, repeatedly press SLEEP until it is set to 0
minutes.
Automatic Power Down
The TV can be configured to automatically turn itself off after 4
hours if you do not operate the TV either from the remote control or
the TV control panel.
1
2
3
From the Preferences menu, highlight Energy Saving
Settings and press ENTER.
Press the (
/
arrow) buttons to select Automatic Power
Down.
Press the (
EXIT.
/
arrow) buttons to select On or Off, and press
NOTE
The default setting of this feature is Off.
One minute before the TV switches to standby, a warning message
will appear.
When the following features are set, the feature that is set for the
nearest time will function.
❖ Automatic Power Down
❖ Sleep Timer
❖ No signal auto power off (after 15 minutes of no signal)
No Signal Power Down
The TV will automatically turn itself off after 15 minutes when no
signal is detected. You can change the setting to Off for the
following purposes:
❖
❖
Low signal strength of analog channel (no signal detection)
Only Audio L/R is connected to external input to listen to
music through the TV speakers.
To change the no signal power down setting:
1
From the Preferences menu, highlight Energy Saving
Settings and press ENTER.
2
Press the (
Down and press ENTER.
/
arrow) buttons to select No Signal Power
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using HDMI®-CEC
109
3
Press the (
to change, and press the (
Off.
/
arrow) buttons to highlight the item you want
/
arrow) buttons to select On or
NOTE
❖ Default setting for this feature is On.
❖ A warning message will appear 1 minute before the TV turns off.
Using HDMI®-CEC
This is a new feature that uses CEC technology and allows you to
control Toshiba HDMI®-CEC compatible devices from the TV
remote via HDMI® connection (see “HDMI®-CEC connection” on
page 31).
When Enable HDMI®-CEC in the HDMI®-CEC Setup menu is
set to On (see “Setting up HDMI®-CEC” on page 112), the
HDMI®-CEC functions described below will be enabled.
HDMI®-CEC playback device (DVD player, etc.) control
With your TV’s remote control, or using the HDMI®-CEC Player
Control menu, you can control the connected
HDMI®-CEC playback device you are watching.
Available remote control key functions
Button:
PLAY
Description:
Begin playback
STOP
Stop playback
PAUSE
SKIP Forward
SKIP Reverse
FF
Pause the picture during play or record mode
Skip Forward
Skip backward
Fast forward
REW
Rewind/reverse
/
/
/
Navigates menu options
Enters menu options
Return to the previous menu
ENTER
EXIT
NOTE
These functions depend on the devices connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Using HDMI®-CEC
110
HDMI®-CEC Player Control menu functions
To control the HDMI®-CEC player from the menu:
1
2
Press MENU and open the Preferences menu.
Highlight HDMI®-CEC Player Control and press the
ENTER button.
(Sample Image) Preferences menu - HDMI®-CEC Player Control
Press the ( arrow) buttons to select the item you wish to
3
/
control and press the ENTER button.
Item:
Description:
Power
Root Menu
Turns the select device On/Off
Accesses the root menu of the selected device
Contents Menu
Accesses the contents list when you press ENTER. At this time, the
HDMI®-CEC Player Control menu disappears.
Setup Menu
Top Menu
Menu
Accesses the setup menu of a selected device
Accesses the top menu of a selected device
Accesses the menu of a selected device
NOTE
These functions depend on the devices that are connected.
The HDMI®-CEC Player Control item will be grayed out in the
following conditions:
❖ A non-HDMI® input is currently selected.
❖ The Enable HDMI®-CEC item is set to Off.
❖ The connected CEC device is not a playback or recording device.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
111
HDMI®-CEC input source selection
If a HDMI®-CEC device with HDMI® switching capability
(e.g. Audio Receiver) is connected to the HDMI® input, you can
select another HDMI®-CEC device that is connected to the master
HDMI® device using the TV’s INPUT button, see “Selecting the
video input source” on page 59.
VOLUME and MUTE controls of Audio Receiver
With your TV’s remote control, you can adjust or mute the sound
volume of the Audio Receiver.
❖
❖
VOL (+ –) buttons adjust the volume level.
MUTE button turns off the sound.
To use this function:
❖
Set Speaker Preference to Audio Receiver in the
HDMI®-CEC Setup menu.
❖
Confirm that a connected HDMI®-CEC device (such as DVD
player, etc.) is selected for the Audio Receiver input source.
NOTE
These functions depend on the device connected.
Other HDMI®-CEC functions
When the Enable HDMI®-CEC and each item in the
HDMI®-CEC Setup menu are set to On, the following functions
will be enabled.
Item:
Description:
TV Auto Input If a connected HDMI® device starts playing video or audio, the TV will
Switch
automatically switch to the appropriate HDMI® input.
TV Auto Power If a HDMI®-CEC device is turned on, the TV turns on automatically.
Device Auto If the TV is turned off the TV will send a message to turn off all of the
Standby
HDMI®-CEC devices connected to the TV.
Speaker
Preference
From this item, you can set your audio output preference to the TV speakers
or the audio receiver speakers. When this item is set to Audio Receiver, the
TV remote can be used to adjust or mute the volume of the audio. This item
will be grayed out unless a HDMI®-CEC compatible audio receiver is
connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Displaying TV status information
112
NOTE
When you turn on the Audio Receiver, change its input source or
adjust the sound volume, the sound will be output from the audio
receiver’s speakers even if TV Speakers has been selected. Turn the
TV off and on again to output the sound from the TV speakers.
Setting up HDMI®-CEC
To set the HDMI®-CEC Setup:
1
From the Setup menu, highlight HDMI®-CEC Setup and
press the ENTER button.
2
3
Press the (
/
arrow) buttons to highlight Enable
HDMI®-CEC.
Press the (
/
arrow) buttons to select On.
NOTE
If you select Enable HDMI®-CEC Off, the other items will be grayed
out.
4
Press the (
/
arrow) buttons to highlight the
HDMI®-CEC Setup item you want to use, and press the (
/
arrow) buttons to select On or the desired mode.
❖
❖
❖
❖
TV Auto Input Switch: On/Off
TV Auto Power: On/Off
Device Auto Standby: On/Off
Speaker Preference: TV Speakers/Audio Receiver
5
To save the new settings, highlight Done and press the ENTER
button.
To revert to the factory defaults, highlight Reset and press the
ENTER button.
Displaying TV status information
To display TV status information using the RECALL button:
❖
Press the RECALL button on the remote control.
The following information will be displayed (if applicable):
❖
❖
Current input (ANT/CABLE, Video, etc.)
If ANT/CABLE is the current input, either “CABLE” (for
cable TV) or “ANT” (for over-the-air broadcasts).
❖
Channel number (if in ANT/CABLE mode)
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s features
Understanding the last mode memory feature
113
❖
❖
Digital signal strength indicator (bar graph in lower right
corner of box; for ATSC signals only)
Stereo, Mono, or SAP audio status (when in HDMI® input
mode, Dolby Digital, or PCM)
❖
❖
❖
❖
Video resolution
Aspect ratio of incoming video signal (4:3 or 16:9)
V-Chip rating status
GameTimer (if set)
o close the Recall screen, press the RECALL button again.
To display TV status information using INFO, press the INFO
button.
The following additional information will display for off air digital
channels, if applicable:
❖
❖
❖
Title
Duration
Detailed description
(Sample Illustration) Info banner
To close the INFO screen, press the INFO button again.
NOTE
The location of the banner can be moved to the top or bottom of the
screen by pressing or while the RECALL or INFO display is
on-screen.
Understanding the last mode memory feature
If the power is cut off while you are viewing the TV, the Last Mode
Memory feature automatically turns on the TV when the power is
resupplied.
NOTE
If you know you will be away from the TV for an extended period of
time you should unplug the power cord.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter7
Using the TV’s Advanced
Features
Using the advanced picture settings
Dynamic Contrast
Dynamic Contrast detects changes in picture quality that affect the
appearance of your contrast settings and then automatically adjusts
the video.
To select Dynamic Contrast preference:
1
From the Picture menu, highlight Picture Settings and press
the ENTER button.
(Sample Image) Dynamic Contrast screen
2
3
Highlight Advanced Picture Settings, and then press the
ENTER button.
Press the (
/
arrow) buttons to select Dynamic Contrast.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Advanced Features
Using the advanced picture settings
115
4
Press the (
Off.
/
arrow) buttons to select High, Middle, Low or
Static Gamma
The static gamma feature lets you adjust the levels of black in the
picture.
To adjust the static gamma settings:
1
2
3
Press the MENU button and open the Picture menu.
Highlight Picture Settings, and then press the ENTER button.
Highlight Advanced Picture Settings, and then press the
ENTER button.
❖
In the Static Gamma field, press the (
/
arrow) buttons
to adjust the Static Gamma.)The adjustment range is
within 5 from center).
❖
❖
If the setting is decreased, the detail of black colors is
decreased.
If the setting is increased, the detail of black colors is
increased.
4
To save the new settings, highlight Done, and then press the
ENTER button.
To revert the factory defaults, highlight Reset, and then press
the ENTER button.
NOTE
If you select one of the factory-set picture modes (Dynamic,
Standard, Movie or PC) and then change the Static Gamma setting,
the picture mode automatically changes to Preference.
Color temperature
You can change the quality of the picture by selecting from three
preset Color Temperatures (Cool, Medium, and Warm), as
described below.
Mode:
Cool
Picture Quality:
blueish
Medium
Warm
neutral
reddish
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Advanced Features
Using the advanced picture settings
116
To select the color temperature:
1
2
3
Press the MENU button and open the Picture menu.
Highlight Picture Settings, and then press the ENTER button.
Highlight Advanced Picture Settings, and then press the
ENTER button.
4
5
Highlight Color Temperature, and then press the (
/
arrow) buttons to select the mode you prefer (Cool, Medium,
or Warm).
Press the (
/
arrow) buttons to select either B Drive or G
Drive, and then press the (
/
arrow) buttons to adjust the
settings:
❖
❖
B Drive: press the ( arrow) button to make the picture
blueish.
G Drive: press the ( arrow) button to make the picture
greenish.
NOTE
The B Drive and G Drive settings are connected to the Color
Temperature settings and will change based on which setting is
selected in step 5 above.
6
To save your new settings, highlight Done, and then press the
ENTER button.
To revert to your original settings, highlight Reset, and then
press the ENTER button.
NOTE
If you select one of the factory set picture modes (Dynamic,
Standard, Movie, or PC) and then change the Color Temperature
mode, the picture mode automatically changes to Preference.
ClearFrame™ (L5200U Series)
The new ClearFrame 120 Hz anti-blur technology doubles the
frame rate from 60 frames per second to 120 frames per second,
virtually eliminating motion blur without adding flicker or reducing
image brightness.
To turn on ClearFrame:
1
2
Press the MENU button and open the Picture menu.
Highlight Picture Settings and press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Advanced Features
Using the advanced picture settings
117
3
Highlight Advanced Picture Settings and press the ENTER
button.
4
5
In the ClearFrame field, select On.
To save the new settings, highlight Done and press the ENTER
button.
To revert to the factory defaults, highlight Reset and press the
ENTER button.
NOTE
❖ If you select one of the factory-set picture modes (Dynamic,
Standard, Movie or PC) and then change the ClearFrame setting,
the picture mode automatically changes to Preference.
❖ When ClearFrame is set to Off, the Film Stabilization feature will
not be available (grayed out and set to Off).
Film Stabilization (L5200U Series)
This feature helps to eliminate video shaking.
To turn on Film Stabilization:
1
2
3
Press the MENU button and open the Picture menu.
Highlight Picture Settings and press the ENTER button.
Highlight Advanced Picture Settings and press the ENTER
button.
4
5
In the Film Stabilization field, select Smooth, Standard or
Off.
To save the new settings, highlight Done and press the ENTER
button.
To revert to the factory defaults, highlight Reset and press the
ENTER button.
NOTE
❖ If you select one of the factory-set picture modes (Dynamic,
Standard, Movie or PC) and then change the Film Stabilization
setting, the picture mode automatically changes to Preference.
❖ When ClearFrame is set to Off, Film Stabilization will be grayed
out and set to Off automatically.
❖ When slow motion video is present the units will treat any
scrolling text as Film and may cause a slight jitter of the
scrolling text. Tuning Off the Film Stabilization feature will
correct this issue.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Advanced Features
Using the advanced picture settings
118
CableClear® digital Noise Reduction
The CableClear® digital Noise Reduction feature allows you to
reduce visible interference in your TV picture. This may be useful
when receiving a broadcast with a weak signal (especially a Cable
channel) or playing a noisy video cassette or disc.
To change the CableClear settings:
1
2
Press the MENU button and open the Picture menu.
Highlight Noise Reduction, and then press the ENTER
button.
3
In the CableClear field, select the desired setting. The
available selections are Off, Low, Middle, and High. Low,
Middle, and High will reduce the noise in varying degrees,
from lowest to highest, respectively.
NOTE
If the current input is ANT/CABLE or VIDEO, the menu will display
the text “CableClear”. If the current input is ColorStream® HD,
HDMI 1 HDMI 2, or HDMI 3, the menu will display the text “DNR”.
4
To save your new settings, highlight Done, and then press the
ENTER button.
To revert to your original settings, highlight Reset, and then
press the ENTER button.
MPEG Noise Reduction
The MPEG Noise Reduction feature allows you to reduce visible
interference caused by MPEG compression. Choices for MPEG
Noise Reduction are Off, Low, Middle, and High. Off is
automatically selected when this feature is disabled (“grayed out”).
To select the MPEG Noise Reduction level:
1
2
Press the MENU button and open the Picture menu.
Highlight Noise Reduction, and then press the ENTER
button.
3
4
Press the (
Reduction field, and then press the (
select either Off, Low, Middle, or High.
/
arrow) buttons to highlight the MPEG Noise
/
arrow) buttons to
To save your new settings, highlight Done, and then press the
ENTER button.
To revert to your original settings, highlight Reset, and then
press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the TV’s Advanced Features
Using the advanced picture settings
119
Game Mode
You can use the Game Mode feature for shorter frame delays when
you need split-second timing between the on-screen display and
input from the controller (such as music creation and high-action
games).
This feature is more effective for 480i and 1080i input signals.
NOTE
To use the Game Mode feature, the current video input must be
Video, ColorStream® HD, HDMI 1, HDMI 2, or HDMI 3. The Game
Mode cannot be turned on when any other video input, other than the
above mentioned is selected.
To turn on Game Mode:
1
2
Press the MENU button and open the Picture menu.
Press the ( arrow) buttons to select On.
/
To turn off Game Mode, select Off in step 2 above, change the
video input, or turn the TV off and then on again.
NOTE
You can change the video input by pressing INPUT on the remote
control, see “Selecting the video input source” on page 59.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter8
Troubleshooting
General troubleshooting
Before calling a service technician, review this chapter or visit the
possible causes/solutions for the problem you are experiencing.
Before you begin to troubleshoot any problem, first unplug the TV
from the AC wall outlet, wait approximately one minute, and then
plug the TV back into the AC wall outlet. If the problem still exists
attempt to troubleshoot the problem.
Black box on-screen.
The closed caption feature is set to one of the Text modes (T1, T2,
T3, or T4). Set the closed caption feature to Off, see “Using closed
captions” on page 80.
TV stops responding to controls.
If the TV stops responding to the buttons on the remote control or
TV control panel and you cannot turn off the TV, press and hold
POWER button on the TV control panel for several seconds to
reset the TV. If the TV does not power off using this method,
unplug the TV from the AC wall outlet and plug it back in.
If you cause a static discharge when touching the TV and the TV
fails to function, simply unplug the TV from the AC outlet and plug
it back in. The TV should return to normal operation.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Picture problems
121
Other problems.
the recommended solution has not worked, use the Reset Factory
Defaults procedure, see “Resetting Factory Defaults” on page 58.
TV will not turn on.
Ensure the power cord is plugged in properly, and then press the
POWER button.
batteries” on page 40.
Try the control panel buttons on the TV.
Picture problems
General picture problems.
Check the antenna/cable connections, see “Connecting Your TV”
on page 21.
Press the INPUT button on the remote control or on the TV and
select a valid video input source, see “Selecting the video input
device connection details, see “Connecting Your TV” on page 21.
Antenna reception may be poor. Use a highly directional outdoor
antenna (if applicable).
The station may be having broadcast difficulties. Try another
channel.
Adjust the picture quality, see “Using the advanced picture settings”
on page 114.
Cannot view external signals or channel 3 or 4.
VIDEO, ColorStream HD1, ColorStream® HD, HDMI 1, HDMI 2,
PC, or from channel 3 or 4, ensure that the Input Lock is set to Off,
see “Using the Locks menu” on page 87.
Noisy picture.
If you are watching an analog channel (off-air broadcast or Cable
TV), you can set the CableClear® feature to reduce visible
interference in the TV picture, see “CableClear® digital Noise
Reduction” on page 118.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Picture problems
122
Video Input Selection problems
If the Input Selection window does not appear when you press
INPUT on the remote control or TV, press INPUT a second time.
This will cause a change to the next video input source and display
the Input Selection window.
Cannot view external signals or channel 3 or 4
If you cannot view signals from external devices connected to
VIDEO, ColorStream® HDMI 1, HDMI 2, HDMI 3 (L5200U
Series), or PC or from channels 3 or 4, make sure the Input Lock is
set to Off, see “Using the input lock feature” on page 95.
Poor display color or no color.
The station may be having broadcast difficulties. Try another
channel.
Adjust the Tint and/or Color, see “Color temperature” on page 115.
Poor composite picture.
If the TV is connected to an external A/V device (e.g. DVD player,
video game system, set-top box, etc.) try using a ColorStream® or
HDMI® video connection instead.
Picture and sound are out of sync.
As with all products that contain a digital display, this may occur in
rare instances, when viewing certain content (e.g. television
broadcasts, video games, DVDs). The cause may include, without
limitation, video processing within the TV, video processing in an
attached gaming system, and video processing or different
compression rates used by broadcasters in their programming.
Try the following:
❖
If the TV is connected to an A/V receiver that has a
programmable audio delay feature, use this feature to help
synchronize the sound to the picture.
❖
❖
If the problem occurs only on certain TV channels, inform
your local broadcast, cable, or satellite provider.
Digital audio settings may not be correct. Check the
connections, see “Connecting a digital audio system” on
page 33.
❖
Turn off and unplug the TV from the AC wall outlet for a few
seconds and plug it back in.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Sound problems
Scrolling text problem
text as film and may cause a slight jitter of the scrolling text.
Turning off the Film Stabilization feature will correct this issue, see
“Film Stabilization (L5200U Series)” on page 117. (L5200U Series
only)
Sound problems
Check the antenna/cable connections, see “Connecting a VCR,
antenna, cable TV, or camcorder” on page 24.
The station may be having broadcast difficulties. Try another
channel.
The sound may be muted. Press the VOL (+) button.
If you hear no sound, try setting the MTS feature to Stereo mode,
see “Selecting stereo/SAP broadcasts” on page 84.
If you are not receiving a second audio program from a known SAP
source, make sure the MTS feature is set to SAP mode, see
“Selecting stereo/SAP broadcasts” on page 84.
If you hear audio that seems incorrect for the program you are
watching (such as music or a foreign language), the SAP mode may
be on. Set the MTS feature to Stereo mode, see “Selecting
stereo/SAP broadcasts” on page 84.
If you connect a computer using either the PC IN terminal or an
HDMI® terminal, make sure that the audio setting is properly set,
see “Connecting a digital audio system” on page 33.
Remote control problems
Replace the remote control’s batteries, see “Installing batteries” on
page 40.
Your TV’s remote control may not operate certain features on your
external devices. Refer to the User's Guide for your other device to
determine its available features. If your TV remote control does not
operate a specific feature on another device, use the remote control
that came with the device, see “Learning about the remote control”
on page 42.
If the TV still does not act as expected, perform the Reset Factory
Defaults procedure, see “Resetting Factory Defaults” on page 58.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Channel tuning problems
124
Channel tuning problems
Ensure that the remote control is set to the correct device mode, see
“Learning about the remote control” on page 42.
The Auto Tuning feature may have erased the channel from
memory. Add the channel to the channel memory, see “Storing
channels in memory (optional)” on page 51.
channel, see “Locking channels” on page 96.
If you cannot tune digital channels, check the antenna
configuration. If the problem persists, clear all channels from the
channel list and reprogram channels into memory, see “Storing
channels in memory (optional)” on page 51. For additional
information, see “TV stops responding to controls.” on page 120. If
“Resetting Factory Defaults” on page 58
Closed caption problems
If the program or video you have selected is not closed captioned,
no captions appear on the screen.
If text is not available, a black rectangle may appear. If this
happens, turn off the closed caption feature, see “Using closed
captions” on page 80.
A closed caption signal may not display correctly under the
following circumstances:
❖
❖
❖
The recording is dubbed
The signal reception is weak
For additional information, see “Using closed captions” on page 80.
Rating blocking (V-Chip) problems
Forgotten PIN code.
When the PIN code screen appears, press the INFO button 4 times
within approximately 5 seconds. The old PIN code is cleared, see
“Forgotten PIN code” on page 89.
The V-Chip feature is available for U.S. V-Chip systems only, see
“Using parental controls (for USA region)” on page 89.
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
No HDMI®-CEC operation
125
No HDMI®-CEC operation
The HDMI®-CEC feature is available for Toshiba
HDMI®-CEC compatible devices.
Ensure that HDMI® cables with the (
) Logo are used.
When the connected HDMI®-CEC device does not work correctly
after you have changed settings of the device, turn off your TV and
unplug the power cord, then plug in and turn on again.
If several devices are connected, the HDMI®-CEC feature may not
operate properly.
HDMI®-CEC device.
HDMI® problems
HDMI® cables.
Ensure that HDMI® cables with the (
) Logo are used, see
“Connecting an HDMI® or DVI device to the HDMI® input” on
page 28.
Legacy HDMI® sources.
Some legacy HDMI® sources may not work properly with the latest
HDMI® TV products due to new standard adoption.
Media Player problems
Incorrect functionality may occur when using a USB HUB
connection.
Photo files that were processed and edited using the computer’s
application software may not be viewable.
The TV may select one format automatically and play it when
contents that support two or more formats are played.
Confirm that the contents of the USB storage device are in formats
that are supported by this TV, see “Using the Media Player” on
page 100.
If the problem persists after trying the solutions
Contact Toshiba at:
For technical support, call the Toshiba Customer Support Center:
Within the United States, at 800-631-3811
Outside the United States, at 949-583-3050
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
NOTE
❖ These models comply with the specifications listed below.
❖ Designs and specifications are subject to change without notice.
❖ These models may not be compatible with features and/or
specifications that may be added in the future.
Television system
NTSC standard
ATSC standard 8VSB
Digital Cable
64 QAM, 256 QAM; in-the-clear, unencrypted
Channel coverage
VHF
2 through 13
UHF
14 through 69
Cable TV
Mid band (A-8 through A-1, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power source
127
Power source
120V AC, 60 Hz
Power maximum current
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
0.9 A
1.0 A
1.0 A
0.9 A
1.1 A
1.3 A
Power consumption
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
0.6 W in Standby mode
0.6 W in Standby mode
0.6 W in Standby mode
0.6 W in Standby mode
0.6 W in Standby mode
0.6 W in Standby mode
Audio power
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
6
6
6
6
6
6
5W
5W
7W
7W
7W
7W
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Speaker type
128
Speaker type
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
Two 3.7 x 1.06 x 0.8”
Two 3.58 x 0.98 x 0.9”
Two 3.93 x 1.18 x 0.78”
Two 10.38 x 2.6 x 0.71” (Box type)
Two 10.38 x 2.6 x 0.71” (Box type)
Two 10.38 x 2.6 x 0.71” (Box type)
Video/audio terminals
Video/audio input
Video
Audio
1 V (p-p), 75 ohm, negative sync.
200 mV(rms) (-20dBFS, 47K ohm or greater)
ColorStream® (component video) HD input
Video
Y: 1V(p-p), 75 ohm
PR: 0.7 V(p-p), 75 ohm
PB: 0.7 V(p-p), 75 ohm
Suggested formats: 1080i, 720p, 480p, 480i
200 mV(rms) (-20dBFS, 47K ohm or greater)
Audio
HDMI® input
HDMI® compliant (type A connector)
HDCP compliant
2-channel Linear-PCM; 32/44.1/48 kHz sampling
frequency; 16/20/24 bits per sample
HDMI® Audio
Digital audio output
Optical type
PC input
15-Pin D-sub Analog RGB
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Dimensions
129
Dimensions
Width
Height
Depth
Width
Height
Depth
Width
Height
Depth
Width
Height
Depth
Width
Height
Depth
Width
Height
Depth
1'-5 1/2” (445.8mm)
19L4200U
1'-3/4” (324.5mm)
7” (445.8mm)
1'-10 3/8” (567.52mm)
1'-2 1/4” (362.54mm)
7” (177.52mm)
24L4200U
32L4200U
40L5200U
46L5200U
2'-5 3/8” (745.4mm)
1'-7 7/8” (505.21mm)
7'-1/8” (179.52mm)
3'-1/2” (928mm)
2” (610.45mm)
10'-1/8” (256.58mm)
3'-5 3/4” (1061.5mm)
2'-3” (685.7mm)
10'-1/8” (257.6mm)
3'-8 3/4” (1138.2mm)
2'-4 3/4” (728.9mm)
11'-3/8” (287.6mm)
50L5200U
Mass (weight)
19L4200U
24L4200U
32L4200U
40L5200U
46L5200U
50L5200U
7.7 lbs (3.5 kg)
9.9 lbs (4.5 kg)
17.6 lbs (7.9 kg)
36.4 lbs (16.5 kg)
43.0 lbs (19.5 kg)
48.4 lbs (21.9 kg)
Operating conditions
Temperature
Humidity
32 - 95º F (0 - 35º C)
20 - 80% (no moisture condensation)
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Supplied accessories
130
Supplied accessories
❖
❖
❖
❖
Remote control with two size “AAA” batteries
Resource Guide
Quick Start Guide
Pedestal and hardware
Acceptable signal formats for PC IN, HDMI®
PC IN signal formats
NOTE
Depending on the connected PC, the following conditions may
occur; incorrect display, false format detection, picture position
failure, blur, or judder. This is not a malfunction of your TV.
Format Resolution V. Frequency
H. Frequency
Pixel Clock
Frequency
VGA
SVGA 800 x 600
XGA 1024 x 768
WXGA 1280 x 768
640 x 480
59.940 Hz
60.317 Hz
60.004 Hz
59.870 Hz
31.469 kHz
37.879 kHz
48.363 kHz
47.776 kHz
47.712 kHz
63.981 kHz
25.175 MHz
40.000 MHz
65.000 MHz
79.500 MHz
85.500 MHz
108.000 MHz
1360 x 768 60.015 Hz
SXGA 1280 x 1024 60.020 Hz
HDMI® signal formats
Format Resolution V. Frequency
H. Frequency
Pixel Clock
Frequency
VGA
640 x 480
59.940 Hz
60.317 Hz
60.004 Hz
59.870 Hz
31.469 kHz
37.879 kHz
48.363 kHz
47.776 kHz
47.712 kHz
63.981 kHz
15.734 kHz
25.175 MHz
40.000 MHz
65.000 MHz
79.500 MHz
85.500 MHz
108.000 MHz
27.000 MHz
SVGA 800 x 600
XGA
1024 x 768
1280 x 768
WXGA
1360 x 768 60.015 Hz
SXGA 1280 x 1024 60.020 Hz
480i 720 x 480i 59.940 Hz
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Acceptable signal formats for PC IN, HDMI®
131
Format Resolution V. Frequency
H. Frequency
Pixel Clock
Frequency
27.000 MHz
74.250 MHz
74.250 MHz
74.250 MHz
148.500 MHz
480p
720p
720 x 480p
59.940 Hz
31.469 kHz
45.000 kHz
33.750 kHz
27.000 kHz
67.500 kHz
1280 x 720p 60.000 Hz
1080i 1920 x 1080i 60.000 Hz
24.000 Hz
1080p 1920 x 1080p
60.000 Hz
NOTE
❖ Some illustrations in this User's Guide are for explanation
purposes and may differ from the actual unit.
❖ Designs and specifications are subject to change without notice.
❖ These models may not be compatible with features and/or
specifications that may be added in the future.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
License Agreement
License Information on the software used in the
TOSHIBA Digital TV
The software pre-installed in the TOSHIBA Digital Televisions consists of multiple,
independent software components. Each software component is copyrighted by TOSHIBA
or a third party.
The TOSHIBA Digital Televisions uses software components that are distributed as
freeware under a third-party end-user license agreement or copyright notice (hereinafter
referred to as a "EULA"). Some EULAs require that the source code of the applicable
component be disclosed as the condition for distributing the software component in
executable format.
In addition, some of the software components which are used in Toshiba Digital Televisions
include the software that are made or developed originally by TOSHIBA. These software
and accompanied documents are copyrighted by TOSHIBA, and protected by Copyright
Act, an international treaty's articles and other governing laws. The software components
which are made or developed originally by TOSHIBA and not subject to EULAs are not a
target of source code offering.
The Toshiba warranty provided in respect of the Digital TV is the only warranty provided
and no additional warranties are provided in respect of the software components subject to
EULAs.
Some of the software components distributed under EULAs are made available for use by
the user on the premise that they are not copyrighted or warranted by TOSHIBA or any third
party. These software components are licensed to the user free of charge and therefore not
covered by any warranty within the scope of the applicable laws. These software
components are provided in "as is" condition without any warranty, whether express or
132
Download from Www.Somanuals.com. All Manuals Search And Download.
License Agreement
133
implied. "Warranty" here includes, but not limited to, an implied warranty for marketability
or fitness for specific uses. All risks associated with the quality or performance of these
software components are assumed by the user. TOSHIBA shall not be liable whatsoever for
any cost of repair or correction or other incidental expense incurred in connection with a
defect found in any of these software components. Unless specified under the applicable
laws or in a written agreement, a party who changes or redistributes the software with
consent from the copyright holders or based on the aforementioned licenses shall not be held
liable whatsoever for any loss arising from the use of or inability to use such software
components. The same applies even when the copyright holders or relevant third parties
have been informed of the possibility of such loss. "Loss" here includes normal, special,
incidental and indirect loss (including, but not limited to, the loss of data or its accuracy; loss
incurred by the user or any third party; and interface incompatibility with other software).
Please read each EULA for details on the use conditions and items that must be observed
regarding these software components.
The table below lists the software components pre-installed in the TOSHIBA Digital
Televisions, which are subject to EULAs. The user should read the applicable EULAs
carefully before using these software components. The EULAs are exhibited in their
original text (English) as exactly written by the respective parties other than TOSHIBA.
For at least three (3) years from the date of distribution of the this product, Toshiba will give
to anyone who contacts Toshiba Consumer Solutions at (800) 631-3811, for a charge of no
more than our cost of physically performing source code distribution, a complete machine-
readable copy of the complete corresponding GPL and LGPL source code for the version of
the GPL and LGPL code that we distributed to you in this product.
Pre-Installed Software - EULA
jpeglib.h - Exhibit A
FreeType 2.2.0 - Exhibit B
scalfact.c - Exhibit C
Exhibit A
The authors make NO WARRANTY or representation, either express or implied, with
respect to this software, its quality, accuracy, merchantability, or fitness for a particular
purpose. This software is provided "AS IS", and you, its user, assume the entire risk as to its
quality and accuracy.
This software is copyright (C) 1991-2011, Thomas G. Lane, Guido Vollbeding.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions
thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file
must be included, with this copyright and no-warranty notice unaltered; and any additions,
deletions, or changes to the original files must be clearly indicated in accompanying
documentation.
(2) If only executable code is distributed, then the accompanying documentation must state
that "this software is based in part on the work of the Independent JPEG Group".
Download from Www.Somanuals.com. All Manuals Search And Download.
License Agreement
134
(3) Permission for use of this software is granted only if the user accepts full responsibility
for any undesirable consequences; the authors accept NO LIABILITY for damages of any
kind.
These conditions apply to any software derived from or based on the IJG code, not just to the
unmodified library. If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author's name or company name in
advertising or publicity relating to this software or products derived from it. This software
may be referred to only as "the Independent JPEG Group's software".
We specifically permit and encourage the use of this software as the basis of commercial
products, provided that all warranty or liability claims are assumed by the product vendor.
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor
of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is NOT covered
by the above copyright and conditions, but instead by the usual distribution terms of the Free
Software Foundation; principally, that you must include source code if you redistribute it.
(See the file ansi2knr.c for full details.) However, since ansi2knr.c is not needed as part of
any program generated from the IJG code, this does not limit you more than the foregoing
paragraphs do.
The Unix configuration script "configure" was produced with GNU Autoconf. It is
copyright by the Free Software Foundation but is freely distributable. The same holds for its
supporting scripts (config.guess, config.sub, ltmain.sh). Another support script, install-sh, is
copyright by X Consortium but is also freely distributable.
The IJG distribution formerly included code to read and write GIF files. To avoid
entanglement with the Unisys LZW patent, GIF reading support has been removed
altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This
technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but
are readable by all standard GIF decoders.
We are required to state that
"The Graphics Interchange Format(c) is the Copyright property of CompuServe
Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."
Exhibit B
The FreeType Project LICENSE
2002-Apr-11
Copyright 1996-2002 by
David Turner, Robert Wilhelm, and Werner Lemberg
Introduction
The FreeType Project is distributed in several archive packages; some of them may contain,
in addition to the FreeType font engine, various tools and contributions which rely on, or
relate to, the FreeType Project.
This license applies to all files found in such packages, and which do not fall under their own
explicit license. The license affects thus the FreeType font engine, the test programs,
documentation and makefiles, at the very least.
Download from Www.Somanuals.com. All Manuals Search And Download.
License Agreement
135
This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses,
which all encourage inclusion and use of free software in commercial and freeware products
alike. As a consequence, its main points are that:
❖ We don't promise that this software works. However, we will be interested in any kind
of bug reports. (`as is' distribution)
❖ You can use this software for whatever you want, in parts or full form, without having
to pay us. (`royalty-free' usage)
❖ You may not pretend that you wrote this software. If you use it, or only parts of it, in a
program, you must acknowledge somewhere in your documentation that you have
used the FreeType code. (`credits')
We specifically permit and encourage the inclusion of this software, with or without
modifications, in commercial products. We disclaim all warranties covering The FreeType
Project and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in
compliance with this license. We thus encourage you to use the following text:
Portions of this software are copyright © 1996-2002 The FreeType
Project (freetype.org). All rights reserved.
Exhibit C
scalfact.c Scalefactors for layer I and II This program is free software; you can redistribute it
and/or modify it under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2 of the License, or (at your option) any later
version. This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this
program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge,
MA 02139, USA.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Auto Aspect
using 76
Numerics
22605
auto power down
set 108
Auto Start function
Media Player 101
AV input mode
setting 55
h3-Heading 3
HDMI®-CEC input source
selection 111
A
advanced picture settings
CableClear® digital Noise
Reduction 118
B
Color temperature 115
Dynamic Contrast 114
MPEG Noise Reduction 118
Static Gamma 115
using 114
blocking programs
C
cables
analog RGB (15-pin) 23
component video (red/white/
yellow) 22
audio
adjusting quality 85
Audyssey ABX™ 86
Dolby® Digital Dynamic Range
Control 87
HDMI® 22
muting sound 83
optical audio 23
overview of cables 21
standard A/V (red/white/yellow)
22
optical audio output format 86
stereo/SAP broadcasts 84
Audyssey Dynamic Volume®
using 86
channel
136
Download from Www.Somanuals.com. All Manuals Search And Download.
switching between two channels
69
F
tuning to the next 68
features 16
Freeze
Channel Browser
elements 66
tuning channels 64
Channel Return
switching between two channels
69
channels
feature 77
using 97
auto tuning 51
locking channels 96
skipping 54
specific channel 69
storing in memory 51
HDMI® audio mode
cinema mode
selecting 77
closed captions
HDMI®-CEC
additional functions 111
CC selector 82
Digital CC settings 81
using 80
adding/clearing inputs 68
computer
setting the audio 99
using with the TV 98
connecting
icon
safety 15
Initial setup 49
initial setup
main menu layout 45
input lock feature
using 95
a computer 35
audio system 33
cable TV 24
computer to TV’s PC IN 35
DVD player with ColorStream®
25
DVI device to HDMI® input 28
HDMI® device to HDMI® input
28
last mode memory feature 113
Locks menu
TV’s HDMI® 37
VCR and antenna 24
connecting HDMI®-CEC 31
setting pin code 87
M
Media Player
open 101
D
digital audio selector
using 83
photo files 103
playing music files 104
using 100
digital signal meter
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
138
menu
deleting 89
layout 47
navigation 47
setup 47
entering PIN code 88
unlocking programs 95
N
no signal power down
set 108
Q
ANT/CABLE IN 50
menu language 50
O
overview
installation 17
setup 17
use 17
R
rating system 92
downloading additional 90
P
S
panel lock feature
using 97
parental controls
blocking programs/movies by
rating (V-Chip) 89
using 89
icons 15
specifications
PC Audio
setting 99
audio power 127
PC settings feature
using 98
picture
adjusting 78
adjusting quality 79
picture mode
selecting 78
picture size
channel coverage 126
ColorStream® HD input 128
HDMI® signal formats 130
PC IN signal formats 130
4
3 74
Dot by Dot 74
Full 71
Native 73
power consumption 127
power maximum current 127
power source 127
Normal 74
speaker type 128
selecting 70
TheaterWide 1 72
TheaterWide 2 72
TheaterWide 3 73
pin code
supplied accessories 130
TV system 126
video/audio terminals 128
SurfLock™
changing 89
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
139
switching between two channels
69
video input sources
labeling 61
system status
viewing 57
T
time zone
setting 57
timer
sleep timer 107
troubleshooting 120
channel tuning problems 124
closed caption problems 124
contact Toshiba 125
HDMI® 125
media player problems 125
No HDMI®-CEC operation 125
picture problems 121
Rating blocking problems 124
remote control problems 123
sound problems 123
TV connections
front 18
side 18
TV panel connections
back 19
TV panel controls
front 18
left side 18
side 18
TV remote
functionality 42
install batteries 40
TV status information
show 112
U
Using Dynamic Volume (Audyssey
Dynamic Volume®) 86
V
video input source
selecting 59
Download from Www.Somanuals.com. All Manuals Search And Download.
|