Operator's Manual
71/4-in. Circular Saw
Model No.
172.10855
12 Amp
®
12
Amp
s
®
C
US
DOUBLE INSULATED
• WARRANTY
• SAFETY
Read, understand and follow
all Safety Rules and Operating Instructions
in this Manual before using this product.
! CAUTION
• UNPACKING
• ASSEMBLY
• DESCRIPTION
• OPERATION
• MAINTENANCE
Sears, Roebuck and Co.,
Hoffman Estates, IL 60179 U.S.A.
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS cont.
PERSONAL SAFETY cont.
!
WARNING: BE SURE to read and understand all instructions in this manual
7. Do not overreach. Keep proper footing and balance at all times. Proper footing and
before using this circular saw. Failure to follow all instructions may result in
balance enables better control of the tool in unexpected situations.
hazardous radiation exposure, electric shock, fire and/or serious personal injury.
8. ALWAYS SECUREYOUR WORK. Use clamps or a vise to hold work when practical.
It is safer than using your hand and frees both hands to operate tool.
WORK AREA SAFETY
9. USE SAFETY EQUIPMENT. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
1. Keep your work area clean and well lit. Cluttered workbenches and dark areas
invite accidents.
10. DO NOT USE ON A LADDER or unstable support. Stable footing on a solid surface
enables better control of the tool in unexpected situations.
2. DO NOT operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases, or dust. Power tools create sparks which may ignite
the dust or fumes.
TOOL USE AND CARE SAFETY
3. Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
!
WARNING: BE SURE to read and understand all instructions before
operating this saw. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious personal injury.
4. Make your workshop childproof with padlocks and master switches. Lock
tools away when not in use.
5. MAKE SURE the work area has ample lighting so you can see the work and that
there are no obstructions that will interfere with safe operation BEFORE using your saw.
1. ALWAYS use clamps or other practical ways to secure and support the workpiece
to a stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
2. DO NOT force the tool. Use the correct tool and blade for your application. The
PERSONAL SAFETY
1. KNOW your power tool. Read the operator's manual carefully. Learn the saw's
applications and limitations, as well as the specific potential hazards related to this tool.
correct tool and blade will do the job better and safer at the rate for which it is designed.
3. DO NOT use the tool if switch does not turn it “On” or “Off”. Any tool that cannot be
controlled with the switch is dangerous and must be repaired.
2. STAY ALERT, watch what you are doing and use common sense when operating
4. DISCONNECT the plug from the power source before making any adjustments,
changing accessories or storing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
a power tool.
3. DO NOT use tool while tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
5. NEVER leave the tool running. ALWAYS turn it off. DO NOT leave the tool until it
4. DRESS properly. DO NOT wear loose clothing or jewelry. Pull back long hair. Keep
your hair, clothing, and gloves away from moving parts. Air vents often cover moving
parts and should also be avoided. Loose clothing, jewelry or long hair can be caught
in moving parts.
comes to a complete stop.
6. STORE idle tools out of the reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
7. MAINTAIN tools with care. Keep cutting tools sharp and clean. Properly maintained
5. AVOID accidental starting. Be sure switch is in “OFF” position before
plugging in. DO NOT carry tools with your finger on the switch. Carrying tools
with your finger on the switch or plugging in tools that have the switch in the
“ON” position invites accidents.
tools with sharp cutting edges are less likely to bind and are easier to control.
8. CHECK for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool's operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
6. REMOVE adjusting keys or wrenches before turning the tool “ON”. A wrench
that is left attached to a rotating part of the tool may result in personal injury.
9. USE ONLY accessories that are recommended for this tool. Accessories that may
be suitable for one tool may become hazardous when used on another tool.
4
5
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
nt.
SAFETY INSTRUCTIONS cont.
EXTENSION CORDS
ELECTRICAL SAFETY
Use a proper extension cord. ONLY use cords listed by Underwriters Laboratories (UL).
Other extension cords can cause a drop in line voltage, resulting in a loss of power and
overheating of tool. For this tool an AWG (American Wire Gauge) size of at least 14-gauge
is recommended for an extension cord of 25-ft. or less in length. Use 12-gauge for an
extension cord of 50-ft. Extension cords 100-ft. or longer are not recommended.
Remember, a smaller wire gauge size has greater capacity than a larger number
(14-gauge wire has more capacity than 16-gauge wire; 12-gauge wire has more capacity
than 14-gauge). When in doubt use the smaller number. When operating a power tool
outdoors, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for
outdoor use and reduce the risk of electric shock.
!
WARNING: Do not permit fingers to touch the terminals of plug when
installing or removing the plug from the outlet.
1. Double insulated tools are equipped with a polarized plug (one blade is wider than
the other).This plug will fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the
plug in any way.
2. Double insulation eliminates the need for the
three-wire grounded power cord and grounded
!
CAUTION: Keep the extension cord clear of the working area. Position the
Cover of
cord so that it will not get caught on lumber, tools or other obstructions while
you are working with a power tool.
power supply system. Applicable only to Class II
Grounded
(double-insulated) tools. This circular saw is
Outlet Box
a double insulated tool.
!
WARNING: Check extension cords before each use. If damaged replace
immediately. Never use tool with a damaged cord since touching the damaged
area could cause electrical shock, resulting in serious injury.
SAFETY SYMBOLS FORYOUR TOOL
The label on your tool may include the following symbols.
V.......................................................................Volts
A......................................................................Amps
!
WARNING: Double insulation DOES NOT take the place of normal safety
Hz....................................................................Hertz
W.....................................................................Watts
precautions when operating this tool.
....................................................................Alternating current
.................................................................Direct current
no ....................................................................No-load speed
....................................................................Class II construction, Double Insulated
RPM……........................………………… . . .Revolutions per minute
SPM……..........................…………………....Strokes per minute
OPM………........................………………......Orbits per minute
3. BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is within the
voltage marked on the tool's data plate. DO NOT use “AC only” rated tools with a DC
power supply.
4. AVOID body contact with grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
5. DO NOT expose power tools to rain or wet conditions or use power tools in wet or
.....................................................................Indicates danger, warning or caution.
It means attention! Your safety is involved.
!
damp locations. Water entering a power tool will increase the risk of electric shock.
6. INSPECT tool cords for damage. Have damaged tool cords repaired at a Sears
Service Center. BE SURE to stay constantly aware of the cord location and keep it well
away from the moving blade.
SERVICE SAFETY
7. DO NOT abuse the cord. NEVER use the cord to carry the tool by or pull the plug
from the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.
1. If any part of this saw is missing or should break, bend, or fail in any way;
or should any electrical component fail to perform properly: SHUT OFF the power
switch and remove the saw plug from the power source and have the missing, damaged
or failed parts replaced BEFORE resuming operation.
2. Tool service must be performed only at a Sears Parts and Repair Center. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
3. When servicing a tool, use only identical replacement parts. Follow instructions in
the maintenance section of this manual. Use of unauthorized parts or failure to follow
maintenance instructions may create a risk of electric shock or injury.
6
7
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
SAFETY INSTRUCTIONS cont.
SAFETY RULES FOR CIRCULAR SAWS cont.
SAFETY RULES FOR CIRCULAR SAWS
11. ALWAYS USE blades that have the correct size and shape (diamond vs. round)
arbor holes. Blades that do not match the mounting hardware of the saw will run
erratically and cause loss of control.
!
DANGER:
Keep hands away from cutting area and blade. Keep your
second hand on the auxiliary handle or motor housing. If both hands are holding
the saw, the blade cannot cut them.
12. NEVER use damaged or incorrect blade washers or bolts. The blade washers and
bolts were specially designed for your saw, for optimum performance and safety of
operation.
!
CAUTION: Blades coast after saw is switched off.
13. NEVER cut more than one piece at a time. DO NOT STACK more than one
1. KEEP your body positioned to either side of the saw blade and not in direct
line with the saw blade. Kickback could cause the saw to jump backwards. (See
“Kickback…What Causes It and Ways to Prevent It” on pages 18 and 19).
workpiece on the worktable at a time.
14. AVOID awkward operations and hand positions where a sudden slip could cause
your hand to move into the blade.
2. DO NOT reach underneath the work. The guard cannot protect you from the blade
15. NEVER reach into the cutting path of the blade.
beneath the workpiece.
!
WARNING: WARNING: Some dust created by using power tools contains
!
DANGER:
When sawing through a workpiece, the lower blade guard DOES
chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints.
NOT cover the blade on the underside of the workpiece (Pg. 17 Fig. 4). ALWAYS
keep your hands and fingers away from the cutting area.
• Crystalline silica from bricks and cement and other masonry products.
• Arsenic and chromium, from chemically treated lumber.
3. CHECK lower guard for proper closing BEFORE each use. DO NOT operate the
saw if the lower guard does not move freely and close instantly. Never clamp or
tie the lower guard in the open position. If the saw is accidentally dropped, the
lower guard may be bent. Raise the lower guard with the retracting lever. The guard is
operating properly when it moves freely, does not touch the blade or any other part in
all angles and depths of cut, and readily returns to the closed position.
Your risk from these exposures varies, depending upon how often you do this
type of work.To reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
4. CHECK the operation and condition of the lower guard spring. If the guard and
the spring are not operating properly, they MUST BE serviced before use. The
lower guard may operate sluggishly, due to damaged parts, gummy deposits, or a
buildup of debris. DO NOT operate your saw until the damage has been repaired or
replaced.
5. The lower guard should be retracted manually ONLY for making special cuts,
such as pocket or compound cuts. ALWAYS raise the lower guard by retracting
its lever. As soon as the blade enters the material, the lower guard MUST be
released. For all other sawing, the lower guard should operate automatically.
6. ALWAYS make sure that the lower guard is covering the blade BEFORE placing
the saw down on a work bench or floor. An unprotected moving blade will cause
the saw to walk backwards, cutting whatever is in its path. Make note of the time it
takes for the blade to stop spinning after the switch is released.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
!
WARNING: Use of this tool can generate and/or disburse dust, which may
cause serious and permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection appropriate for the dust exposure.
Direct particles away from face and body.
7. NEVER hold the piece being cut in your hands or across your legs. It is important
to support the workpiece properly in order to minimize body exposure, blade binding,
or loss of control.
ADDITIONAL RULES FOR SAFE OPERATION
8. HOLD TOOL by insulated gripping surfaces (handles) when performing an
operation where the cutting tool may contact hidden wiring or its own cord.
Contact with a “live” wire will make the exposed metal parts of the tool “live” and shock
the operator.
!
WARNING: BE SURE to read and understand all instructions. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
9. ALWAYS clamp the workpiece securely so it will not move when making the cut.
1. Know your power tool. Read operator's manual carefully. Learn the applications
and limitations, as well as the specific potential hazards related to this tool. Following
this rule will reduce the risk of electric shock, fire or serious injury.
10. When ripping, ALWAYS USE a rip fence or straight edge guide. This improves the
accuracy of the cut and reduces the chance of the blade binding.
11. ALWAYS USE blades that have the correct size and shape (diamond vs. round)
arbor holes. Blades that do not match the mounting hardware of the saw will run
erratically and cause loss of control.
2. ALWAYS wear safety glasses or eye shields when using this saw. Everyday
eyeglasses have only impact-resistant lenses; they are NOT safety glasses.
3. PROTECT your lungs. Wear a face mask or dust mask if the operation is dusty.
8
9
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS cont.
GLOSSARY OF TERMS FOR WOODWORKING
Ripping or Rip Cut
ADDITIONAL RULES FOR SAFE OPERATION cont.
A cutting operation along the length of the workpiece.
4. PROTECT your hearing. Wear appropriate personal hearing protection during use.
Under some conditions and duration of use, noise from this product may contribute
to hearing loss.
Freehand Cut
Performing a cut without using a fence, miter gauge, fixture, work clamp, or other proper
device to keep the workpiece from twisting or moving during the cut.
5. ALL VISTORS AND BYSTANDERS MUST wear the same safety equipment that the
Through Sawing
operator of the saw wears.
Any cutting operation where the blade extends completely through the thickness of
the workpiece.
6. INSPECT the tool cords periodically and if damaged have them repaired at your
nearest Sears Service Center or other Authorized Service Facility. BE AWARE
of the cord location.
Non-Through Cuts
Any cutting operation where the blade does not extend completely through the thickness
of the workpiece, like a dado cut.
7. ALWAYS check the tool for damaged parts. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine if it will operate
properly and perform its intended function. Check for misalignment or binding of moving
parts, breakage of parts, and any other condition that may affect the tool's operation.
A guard or other part that is damaged should be properly repaired or replaced at a
Sears Service center.
Leading End
The end of the workpiece pushed into tool first.
Kerf
The material removed by the blade in a through cut or the slot produced by the blade in a
non-through or partial cut.
Kickback
8. INSPECT and remove all nails from lumber before sawing.
9. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct
others who may use this tool. If someone borrows this tool, make sure they have
these instructions also.
A hazard that can occur when the blade binds or stalls, throwing the workpiece back
toward operator.
Workpiece or Material
The item on which the cutting operation is being done. The surfaces of a workpiece are
commonly referred to as faces, ends and edges.
GLOSSARY OF TERMS FOR WOODWORKING
Gum
A sticky, sap-based residue from wood products.
Spindle
Resin
The shaft on which a blade or cutting tool is mounted. Also called the Arbor.
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one minute.
Saw Blade Path
UNPACKING
The area over, under, behind or in front of the blade, as it applies to the workpiece.
That area which will be or has been cut by the blade.
Set
!
WARNING:Your saw should NEVER be connected to the power source
The distance that the saw blade tooth is bent (or set) outward from the face of the blade.
when you are assembling parts, making adjustments, installing or removing
blades, cleaning or when it is not in use. Disconnecting the saw will prevent
accidental starting, which could cause serious personal injury.
Miter Cut
A cutting operation made with the blade at any angle other than 90o to the fence.
Compound Miter Cut
1. Included with your circular saw is the cutting blade, which is unassembled and packed
separately. Also a blade wrench is stored in the saw's base, for use in installing or
changing the blade.
A compound miter cut is a cut made using a miter angle and a bevel angle at the same time.
Cross cut
A cutting or shaping operation made against the grain of the workpiece.
2. Inspect the saw carefully to make sure that no breakage or damage has occurred during
shipping. If any of the items mentioned are missing (refer to PARTS LIST illustration see
Fig.1 page 12), return the saw to your nearest Sears store or Craftsman outlet to have
the saw replaced.
Bevel Cut
A cutting operation made with the blade at any angle other than 90o to the miter table.
Dado Cut
A non-through cut which produces a square-sided notch or trough in the workpiece
(requires special blade).
!
WARNING: If any parts are broken or missing, DO NOT attempt to plug in
Chamfer Cut
the power cord or operate saw until the broken or missing parts are replaced.
Failure to do so could result in possible serious injury.
A cut removing a wedge from a block of wood so the end (or part of the end) is angled
at other than 90o.
10
11
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY cont.
UNPACKING cont.
PARTS LIST
(Fig. 1)
INSTALLING THE BLADE cont. (Figs. 2 and 2a)
®
12
Amp
!
s
WARNING: BE SURE to wear protective work gloves while handling a saw
blade.The blade can injure unprotected hands.
3. Blade Wrench
(for changing the blade)
WARNING: A 7 1/4-inch blade is the maximum blade capacity of your saw.
!
1. Saw
A larger than 71/4-inch blade will come in contact with the blade guards. Also,
NEVER use a blade that is so thick that it prevents the outer blade washer from
engaging with the flat side of the spindle. Blades that are too large or too thick
can result in an accident causing serious injury.
4. Operator's Manual
2. Blade
(unassembled)
ASSEMBLY
6. Completely remove the spindle clamping screw “A” and the outer “D” washer
(see Fig. 2a).
INSTALLING THE BLADE (Figs. 2 and 2a)
7. The remaining washer is the inner bushing washer that fits around the spindle shaft
and it does not need to be removed.
Carefully remove the blade from its packing, inspect it to be sure that it is not cracked or
damaged.
8. Put a drop of oil onto the inner bushing washer and outer “D” washer where they will
touch the blade.
1. Saw should not be plugged into power source.
!
9. Raise lower blade guard using the blade guard lever and hold it in the raised position
for the next step.
WARNING: To prevent personal injury, ALWAYS disconnect the plug from
power source BEFORE assembling parts, making adjustments or installing blades.
10. Place the saw blade inside the lower blade guard, onto the spindle shaft and against
the inner bushing.
2. Place saw on its side on a flat surface.
3. To loosen the depth-of-cut adjustment lever, raise the saw up all the way and tighten
lever. This gives you easier access to blade mounting area (see Fig. 2a).
NOTE:The teeth of the blade should point upward at the front of the saw as
shown in (Fig. 2a).
4. Place saw upright, on its base and on a flat surface (see Fig. 2a).
5. To loosen the spindle clamping screw “A”, depress the spindle lock button (see Fig. 2).
Place the blade wrench on the spindle clamping screw “A”. Move the wrench back and
forth until you feel the spindle lock button depress further and it locks the blade in
position so the spindle clamping screw can be removed. Keeping the spindle lock button
firmly depressed, turn the spindle screw counterclockwise to remove.
11. Replace the “D” washer.
12. Firmly hold down spindle lock button as you replace the spindle screw and hand
tighten it in a clockwise direction. Then use blade wrench to tighten the spindle
clamping screw thoroughly.
Spindle
NOTE: NEVER use a blade that is too thick to allow the “D” washer to engage
with the flat side of the spindle.
Lock Button
Tighten
Depth-of-Cut
Adjustment Lever
®
REMOVING THE BLADE (Figs. 2 and 2a)
Loosen
1. Unplug the saw.
Fig. 2
2. Follow steps 2. through 6. of “INSTALLING THE BLADE” and remove the blade
(see Fig. 2a).
Outer “D” Washer
Fig. 2a
“A” Spindle
Clamping Screw
Blade Rotation
teeth point up at front
12
13
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION cont.
DESCRIPTION
KNOWYOUR CIRCULAR SAW (Fig. 3)
This Circular Saws have the following features: cont.
Fig. 3
Trigger Switch
Rear Handle
NOTE: Before attempting to use your saw, familiarize yourself with all of the
operating features and safety requirements.
Upper
Blade Guard
Front Assist Handle
Motor Housing
Bevel Scale
Your circular saw has a precision-built electric motor and it should only be connected to
a 120-volt, 60-Hz AC ONLY power supply (normal household current). DO NOT operate
on direct current (DC). This large voltage drop will cause a loss of power and the motor
will overheat. If the saw does not operate when plugged into correct 120-volt,
60-Hz AC ONLY outlet, check the power supply. The saw has an 8-ft., 2-wire power cord
(no adapter needed).
®
12
Amp
s
Lower Blade
Guard Lever
Bevel Adjustment
Locking Lever
Blade Wrench
(stores in base)
This Circular Saws have the following features:
1. 9-10855 12 Amp, 4800 RPM (no-load speed) motor provides power and torque for
Blade
fast, sure cuts in wood, plywood, hardboard and wood-base materials.
Base
2. Quick depth-of-cut adjustments with a maximum depth of cut:
Lower
Blade Guard
Edge Guide
Locking/retaining
Screw
9-10855 - 27/16-in. at 90°; 113/16-in. at 45°
Spindle
Clamping
Screw
Mounting Slots
3. Easy to read Bevel Cut Scale adjusts bevel capacity;
for Edge Guide
(sold separately)
9-10855 ; 0° to 45°
Spindle
Lock Button
4. Die-cast aluminum blade guards are epoxy coated for durability and extra strength
5. Extended length Trigger Switch with Power Lock-off Button for maximum control
and comfort. Power lock-off button must be pressed in for trigger switch to turn saw “on”.
Front Assist
Handle
6. Large stamped Steel Base provides stability, glides smoothly
7. Ergonomically designed Rear Handle and Front Assist Handle provide positive
gripping, control, balance and comfort.
Depth-of-Cut
Adjustment
Lever
8. Includes Craftsman® 24 tooth carbide-tipped steel combination blade.
9. Top mounted Blade Spindle Lock for easy blade changes.
10. Sawdust ejection chute helps direct dust and chips away from operator.
11. Permanently lubricated 100% ball bearings for smooth operation and long life.
12. Durable machined gearing for efficient power transmission.
Motor Housing
Blade Wrench
Depth-of-
Cut Scale
(stores in base)
Base
PRODUCT SPECIFICATIONS 9-10855
Input
12 Amps
Rating
120V, 60Hz AC
No Load Speed
4800 RPMs
Cutting Depth at 90°
Cutting Depth at 45°
Maximum Bevel Angle
Blade Diameter
27/16-in. (61.97mm)
113/16-in. (46.03 mm)
45°
71/4-in. (184 mm)
14
15
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SAW BLADES
OPERATION cont.
KICKBACK…WHAT CAUSES IT AND WAYS TO HELP PREVENT IT (Fig. 5)
The Causes of Kickback
Fig. 4
Lower Blade
Guard lever is
in UP position
when making
a cut
All saw blades need to be
kept clean, sharp and properly
set in order to cut efficiently.
Using a dull blade places a
heavy load on the saw and
increases the danger of
kickback. Keep extra blades on
hand, so sharp blades are
always available. Gum and
wood pitch hardened on the
blade slows the saw down.
Use gum and pitch remover,
hot water or kerosene to
remove them. DO NOT use
gasoline.
Fig. 5
Lower Blade
Guard retracts
automatically
when cut is
Correct Blade Depth
(should not exceed 1/4-in.
below work piece)
Blade is Set Too Deep
Blade 1/4-in. or less
being made
is Exposed on
KICKBACK
Underside of Workpiece
BLADE GUARD
SYSTEM (Fig. 4)
1. Kickback is a sudden reaction to a pinched,
bound or misaligned saw blade, which
causes an uncontrolled saw to lift up and
out of the workpiece and toward
the operator.
Fig. 6
The lower blade guard, attached to your circular saw, is there for your protection and
safety. It should NEVER be altered for any reason. If it becomes damaged or begins
to return slowly or sluggishly, DO NOT operate your saw until the damage has been
repaired or replaced. ALWAYS leave the guard in its correct operating position when
using the saw.
Right
Support
2. When the blade is pinched or bound tightly
by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back
towards the operator.
!
CAUTION: NEVER use the saw when the guard is not operating properly.
The guard should be checked for correct operation before each use. If you drop
your saw, check the lower blade guard and bumper for damage at all depth
settings before using.
3. If the blade becomes twisted or misaligned in
the cut, the teeth at the back edge of the blade
can dig into the top surface of the wood. This
causes the blade to climb out of the kerf and
jump back towards the operator.
NOTE:The guard is operating properly when it moves freely and then readily
returns to the closed position. If for any reason your lower blade guard and
bumper does not close freely, take the saw to your nearest Sears Repair Center
for service before using it.
Fig. 6a
4. Sawing into knots or nails in the workpiece
can cause Kickback.
5. Sawing into wet or warped lumber can
cause Kickback. (see Fig. 6a)
Wrong
Support
6. Forcing a cut, or not supporting the workpiece
correctly can cause Kickback. (see Fig. 6a)
7. Kickback is a result of tool misuse and/or
incorrect operating procedures or conditions.
It can be avoided by taking the proper
precautions, on page 19.
16
17
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION cont.
OPERATION cont.
Ways to Help Prevent Kickback
MAKING DEPTH-OF-CUT ADJUSTMENTS (Fig. 8)
ALWAYS use the correct blade depth setting. The correct blade depth setting for all cuts
should not be more than 1/4-inch below the material being cut (see Fig 5). Allowing more
depth will increase the chance of kickback and cause the cut to be rough. Your saw is
equipped with a depth-of-cut scale that provides increased depth-of-cut accuracy.
The depth-of-cut scale is located on the inside back of the upper blade guard.
!
DANGER:
ALWAYS release trigger switch immediately if the blade binds
or the saw stalls. Kickback could cause you to lose control of the saw. Loss of
control can lead to serious injury.
1. ALWAYS maintain a firm grip with both
Fig. 8
Fig. 7
(see Fig. 7) hands on the saw and
position your body and arms to allow you
to resist Kickback forces. Kickback forces
can be controlled by the operator, if the
proper precautions are taken.
Depth Adjust Lever
Bracket
2. If the blade is binding, or when you are
interrupting a cut for any reason,
Loosen
ALWAYS release the trigger and hold the
saw motionless in the material until the
blade comes to a complete stop. NEVER
attempt to remove the saw from the work
or pull the saw backward while the blade
is in motion, or Kickback may occur.
Indicator Mark
Depth-Of-Cut Scale
Tighten
Base
To Raise
To Lower
CHECK and take corrective action to eliminate the cause of blade binding.
3. Inspect the workpiece for knots or nails before cutting. Never saw into a knot or nail.
4. DO NOT cut warped or wet lumber. (see Fig. 6a)
5. ALWAYS support large panels to minimize the risk of blade pinching and Kickback.
Large panels tend to sag under their own weight (see Fig. 6a). Supports MUST be
placed under the panel, one near the line of cut and one near the edge of the panel
(see Fig. 6).
TO SET THE BLADE DEPTH (Fig. 8a)
1. Unplug the saw.
6. When restarting the saw in the workpiece, CENTER the blade in the kerf and check to
be sure that the saw teeth are not engaged into the material. If the saw blade is binding,
it may walk up or Kickback from the workpiece when the saw is restarted.
!
WARNING: ALWAYS unplug saw before making any adjustments. Failure
to unplug the saw could result in accidental starting which can cause serious
personal injury.
7. DO NOT use a dull or damaged blade. Unsharpened, improperly set, or gummed-up
2. Raise the depth-of-cut adjustment
blades produce narrow kerf which causes excessive friction, blade binding and Kickback.
Fig. 8a
lever to loosen the base (see Fig. 8).
8. KEEP the blade at the correct depth setting. The depth setting should not exceed
1/4-inch below the material being cut (see Fig. 5). BE SURE that the blade depth and
adjusting locking levers are tight and secure BEFORE making a cut. If blade adjustment
shifts while cutting it may cause binding and Kickback.
3. Determine the desired depth of cut.
4. Locate the depth-of-cut scale on the
back of the upper blade guard
(see Fig. 8a).
9. USE EXTRA CAUTION when making a “Pocket Cut” into existing walls or other blind
areas. The protruding blade may cut objects that can cause Kickback.
5. Hold the base of the saw flat against
Depth-
of-Cut
the edge of the workpiece and then
raise or lower the saw until the indicator
Scale
mark on the bracket aligns with the
notch on the blade guard at
the desired depth-of-cut mark.
Adjusting
Bracket
6. Tighten depth-of-cut adjustment lever.
19
18
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION cont.
OPERATION cont.
STARTING A CUT (Fig. 10)
TO HELP MAINTAIN CONTROL cont.:
10. Squeeze the trigger switch to start the saw. ALWAYS let the blade reach full speed
!
WARNING: ALWAYS clamp and support workpiece securely. ALWAYS
before you begin the cut into the workpiece.
maintain proper control of saw. Failure to clamp and support workpiece and loss
of control of saw could result in serious injury.
11. When making a cut, ALWAYS use steady, even pressure. Forcing the saw causes
rough cuts and could shorten the life of the saw or cause Kickback.
12. After completing your cut, release the trigger switch and allow the blade to come to a
1. ALWAYS use your saw with your hands positioned correctly, with one hand operating
complete stop. DO NOT remove the saw from the workpiece while the blade is moving.
the trigger switch and the other on the front assist handle (see Fig. 10).
!
When sawing through a workpiece, the lower blade guard DOES
NOT cover the blade on the underside of the workpiece (see Fig. 4, page 17).
ALWAYS keep your hands and fingers away from the cutting area. Any part of
your body coming in contact with the moving blade will result in serious injury.
WARNING: ALWAYS maintain proper control of the saw to make sawing
safer and easier. Loss of control of the saw could cause an accident resulting in
possible serious injury.
2. NEVER use the saw with your hands positioned
Fig. 10
as shown in Fig. 11
MAKING CROSS CUTS AND RIP CUTS (Fig. 12 and 12a)
To Help Maintain Control:
!
3. ALWAYS support the workpiece near the cut.
WARNING: ALWAYS clamp and support workpiece securely. ALWAYS
maintain proper control of saw. Failure to clamp and support workpiece and loss
of control of saw could result in serious injury.
4. ALWAYS support the workpiece so the cut will be on
your right.
5. ALWAYS clamp the workpiece so it will not move
1. ALWAYS use your saw with your hands positioned correctly (see Fig. 12).
during the cut. Place the workpiece with the good
side down.
Right
!
WARNING: ALWAYS maintain proper control of the saw to make sawing
safer and easier. Loss of control of the saw could cause an accident resulting in
possible serious injury.
NOTE:The good side of the workpiece is the side where appearance is important.
2. When making cross or rip cuts with the 10855, align your line of cut with the right side of
the notch by the 0o indicator (see Fig. 12).
6. Before starting a cut, draw a guideline along the
Fig. 11
desired line of cut, then place the front edge of the
Fig. 12
Line of Cut
0o Indicator
saw base on that part of the workpiece that is solidly
supported (see Fig.10).
7. NEVER place the saw on the part of the workpiece
that will fall off when the cut is made (see Fig. 11).
8. ALWAYS keep the cord away from the cutting area.
ALWAYS place the cord so it does not hang up on
the workpiece when making a cut.
Wrong
9. Hold the saw firmly with both hands (see Fig 10).
WARNING: If the cord hangs up on the workpiece during a cut, release the
trigger switch immediately.To avoid injury, unplug the saw and move the cord to
prevent it from hanging up again.
NOTE: Since the thickness of blades varies, MAKE A TRIAL CUT in scrap material
along the guideline to determine how much, if any, you should offset the blade
from the guideline to allow for the kerf of the blade to get an accurate cut.
Using the saw with a damaged cord could result in serious injury
or death. If the cord has been damaged, have it replaced before using the saw again.
20
21
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION cont.
MAKING RIP CUTS
OPERATION cont.
HOW TO SETYOUR BEVEL ANGLE (Fig. 15)
ALWAYS use a guide when making long or wide rip cuts with your saw.You can use
either a straight edge or use the edge guide that was included with your saw.
1. Unplug the saw.
Fig. 15
!
WARNING: ALWAYS unplug saw
!
WARNING: ALWAYS clamp and support workpiece securely. ALWAYS
before making any adjustments. Failure
to unplug the saw could result in
accidental starting which can cause
serious personal injury.
maintain proper control of saw. Failure to clamp and support workpiece
combined with loss of control of saw could result in serious injury.
1.You can make an efficient rip guide
by clamping a straight edge to your
workpiece.
Bevel
Pointer
2. Loosen bevel adjustment lever (see Fig.15).
3. Raise the motor housing end of the saw
until you reach the desired angle setting on
he bevel scale.
2. Carefully guide the saw along the
straight edge for a straight rip cut
(see Fig. 13).
4. Tighten the adjustment lever securely.
Bevel Adjustment Lever
3. ALWAYS LET THE BLADE REACH
Straight
Edge
FULL SPEED, then carefully guide
the saw into the workpiece. DO NOT
MAKING BEVEL CUTS (Figs. 16)
bind the blade in the cut. Push the
saw forward at a speed where the
Fig. 13
Line of Cut
45o Indicator
blade is not laboring.
Fig. 16
INSTALLING AND USING THE EDGE GUIDE (sold separately) (Fig. 14)
Edge guide allows you to make accurate parallel cuts when trimming a workpiece.
It attaches to the saw's base.
1. Unplug the saw.
!
WARNING: ALWAYS unplug saw before making any adjustments. Failure
to unplug the saw could result in accidental starting which can cause serious
personal injury.
2. Position the edge guide so the arm
Fig. 14
with the inch increments is facing “up”.
Slide the arm of the edge guide into
the mounting slots at the front of the
saw's base (see Fig. 14).
!
WARNING: ALWAYS clamp and support workpiece securely. ALWAYS
maintain proper control of saw. Failure to clamp and support workpiece and
loss of control of saw could result in serious injury.
3. Adjust the edge guide to the desired
length of cut.
4. Tighten the edge guide retaining screw.
5. Clamp and support the workpiece
securely before making your cut.
6. Place the edge guide firmly against the
edge of the workpiece (See Fig. 14).
Doing this will give you a true cut without pinching the blade.
7. BE SURE that the guiding edge of the workpiece is straight so you can get a straight cut.
8. ALWAYS LET THE BLADE REACH FULL SPEED, then carefully guide the saw into the
workpiece. DO NOT bind the blade in the cut. Push the saw forward at a speed where
the blade is not laboring.
1.Your saw can be adjusted to cut at any angle between 0° and 45°.
2. When making 45° bevel cuts, line the left side of the notch in the saw's base with the
penciled line of cut on your workpiece (see Fig. 13).
3. When making a bevel cut HOLD the saw FIRMLY with both hands (see Fig. 16).
4. Rest the front edge of the base on the workpiece, then squeeze the trigger switch to start
the saw. ALWAYS let the blade reach full speed, then guide the saw into the workpiece.
5. After completing your cut, release the trigger switch and allow the blade to come to a
complete stop in the cut. DO NOT remove the saw from the workpiece while the blade
is moving. It will damage your bevel cut and cause Kickback.
Rip/Edge Guide
Place Rip/Edge GuideThrough Slots
22
23
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
OPERATION cont.
MAKING BEVEL CUTS (Figs. 16) cont.
!
WARNING: To ensure safety and reliability, all repairs - with the exception
of the externally accessible brushes - should be performed by a qualified service
technician at a Sears Service Center.
!
WARNING: If the blade comes in contact with the workpiece before it
reaches full speed, it could cause the saw to kickback towards you, possibly
resulting in serious injury.
!
WARNING: For your safety, ALWAYS turn off switch and unplug circular
saw from the power source before performing any maintenance or cleaning.
NOTE: Since the thickness of blades varies, MAKE A TRIAL CUT in scrap material
along the guideline to determine how much, if any, you should offset the blade
from the guideline to allow for the kerf of the blade to get an accurate cut.
It has been found that electric tools are subject to accelerated wear and possible
premature failure when they are used to work on fiber glass boats and sports cars,
wallboard, spackling compounds or plaster. The chips and grindings from these materials
are highly abrasive to electrical tool parts, such as bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be used for extended work on any
fiberglass material, wallboard, spackling compound or plaster. During any use on these
materials, it is extremely important that the tool is cleaned frequently by blowing with an
air jet.
MAKING POCKET CUTS ( Fig. 17)
!
WARNING: ALWAYS adjust bevel setting to zero before making a pocket
cut. Attempting a pocket cut at any other setting can result in a loss of control of
the saw, which can result in serious injury.
!
WARNING: Always wear safety goggles or safety glasses with side shields
1. Adjust the bevel setting to zero, set the blade to the correct blade depth setting, then use
the lower blade guard lever to swing the guard up.
during power tool operations, or when blowing dust. If operation is dusty, also
wear a dust mask.
!
WARNING: ALWAYS raise the lower blade guard with the lever to avoid
serious injury.
ROUTINE MAINTENANCE
2. While holding the lower blade
Fig. 17
!
guard up by the lever, firmly rest
WARNING: DO NOT at any time let brake fluids, gasoline, petroleum-based
the front of the saw base flat
against the workpiece with the
rear handle raised so the blade
does not touch the workpiece
(see Fig 17).
products, penetrating oils, etc. come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic, which may result in serious personal injury.
Periodic maintenance allows for long life and trouble-free operation. A cleaning, lubrication
and maintenance schedule should be maintained. As a common preventive maintenance
practice, follow these recommended steps:
3. Squeeze the trigger switch to start
the saw. ALWAYS let the blade
reach full speed, then slowly lower
the blade onto the workpiece until
the base is flat against the
workpiece. AS the blade enters
the material, you MUST release
the lower blade guard lever.
1. When work has been completed, clean the tool to allow smooth functioning of the tool
over time.
2. Use clean damp cloths to wipe the tool.
3. Check the state of all electrical cables.
4. Keep the motor air openings free from oil, grease and sawdust or woodchips, and store
tool in a dry place.
4. After you complete the cut, release the trigger switch and allow the blade to come to a
complete stop. After the blade has stopped, remove it from the workpiece. If the corners
of your pocket cut are not completely cut through, use a hand finishing saw to finish
the corners.
5. Be certain that all moving parts that are exposed are well lubricated, particularly after
lengthy exposure to damp and/or dirty conditions.
LUBRICATION
!
WARNING: NEVER tie the lower blade guard in the raised position. Leaving
All of the bearings in this tool are lubricated with a sufficient amount of high-grade lubricant
for the life of the tool under normal operating conditions. Therefore, no further lubrication is
required.
the blade exposed could result in serious injury.
24
25
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
TROUBLESHOOTING
If the blade does not follow a straight line:
• Teeth are dull. This is caused by hitting a hard object such as a nail, dulling
teeth on one side. The blade tends to cut to the side with the sharpest teeth.
• Base is out of line or bent.
• Blade is bent.
• Edge guide or straight edge is not being used.
If the blade binds or smokes from friction:
• Blade is dull.
• Blade is on backwards.
• Blade is bent.
• Workpiece is not properly supported.
• Incorrect blade is being used.
ACCESSORIES
!
WARNING: The use of attachments or accessories that are not
recommended for this tool might be dangerous and could result in serious injury.
Sears and other Craftsman outlets have a large selection of 7 1/4-inch Craftsman
steel carbide-tipped blades designed for specific cutting applications.
Contractor bulk packs are also available.
Sears and other Craftsman outlets also offer sawhorses, combination and
framing squares, straight edges, edge guides, and a large assortment of
clamps to help you with all your sawing needs.
Visit your local Sears store or other Craftsman outlets or shop sears.com/craftsman.
26
27
REV 10855
2-12-08
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
|