Before installing and using the camera, please read this manual
carefully. Be sure to keep it handy for later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety Guard
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
This Class B digital apparatus complies with Canadian ICES-003.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Cet appareil numerique de la Classe B est conforme a la norme
NMB-003 du Canada.
Changes or modifications not expressly approved by
void the user’s authority to operate this camera.
may
This installation should be made by a qualified service person and
should conform to all local codes.
English
1
Download from Www.Somanuals.com. All Manuals Search And Download.
• Built-in interline transfer method 1/3" CCD, approx. 270,000
PRECAUTIONS........................................................................................ 3
PARTS NAMES AND FUNCTIONS ......................................................... 4
CONNECTIONS AND INSTALLATION ................................................... 6
SETTINGS AND ADJUSTMENTS ........................................................... 9
TROUBLESHOOTING ............................................................................. 9
SPECIFICATIONS.................................................................................... 10
picture elements
• Low smear, anti-blooming, low lag, no burning and no geometric
distortion using the CCD solid state image device
• Built-in fixed focal lens, F=2.0, f=3.8 mm
• 100% solid state components giving excellent immunity to shock
and vibration
• Not subject to interference from magnetic or electrostatic fields
• Built-in IR. LED by very required mininum illumination is approx.
0 lux at 4.5 m
• Horizontal resolution, more than 400 TV lines
1 Vertical holder plate ................................................................ 1 pc.
• Power supply: 24 V AC operation
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2
English
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Install where the temperature range will stay between –10˚C and
50˚C. (no condensation)
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.
• Dirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with dry soft
cloth.
• Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
English
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
8
9
The focus does not need adjustment for subjects 1 m and more
from the lens. If the subject is closer than 1 m, turn the focus ring
to adjust the focus as necessary. (See page .)
8
3
4
This cover will protect the lens from dust and damage.
5
5
7
6
With this camera use only the 24 V AC
power adaptor model No.
available from Sanyo.
Use a 3 wire grounded cable (22 AWG
or more), and connect as shown by the
illustration.
1
2
F
3
•To prevent camera and/or AC adaptor
failure, pay close attention polarity
when making the connections.
•To prevent fire hazard any UL listed
wire rated VW-1, should be used for
the 24 V AC cable input terminal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
English
6
F
When mounting the camera to the mounting bracket, use this
installation hole.
When using a camera switcher to connect 2 cameras or more to
one monitor, there may be a vertical roll of the images when
switched. In such a case, set as described below.
7
8
Loosen the GND terminal screw, insert the coaxial cable into the
clamp and tighten the GND terminal screw.
If more than two cameras are used, please repeat this procedure
for all the cameras.
9
Align the centre wire of the coaxial cable with the VIDEO OUT
terminal, then first tighten the cable clamp and then the VIDEO
OUT terminal screw.
If the vertical roll cannot be corrected by setting the
volume on camera 2, try setting the
volume on camera
• Cable type RG-6U (5C-2V)
1. If it still cannot be corrected, please check that the polarity of the
power cords of all connected devices is correct.
The view angle of this camera is as follows:
Horizontal:
Vertical:
Diagonal:
71˚
53˚
90˚
To adjust the camera angle, use the camera
mounting bracket (sold separately).
English
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Loosen the VIDEO OUT terminal screw ( ) and the GND terminal screw ( ), then insert the
center wire of the coaxial cable in the VIDEO OUT terminal and make sure the shielding
mesh part of the cable is located into the GND cable clamper, then tighten both screws (
and ) to attach the cable.
1
(Return the shielding mesh here)
1
2
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
6
English
To connect the camera to peripheral devices, use a coaxial cable with BNC plug.
1
• Cable type RG-6U (5C-2V), 500 m maximum.
7mm 8mm
If the type of peripheral devices connected, the type of cable used and/or the cable
length are not as specified, the image and synchronization signals may not be
transmitted correctly.
Use CCTV/Video grade coaxial cable. Due to its construction, an RG-59U cable will not
transmit the signal properly when installed through conduits or through the air, and
therefore cannot be used.
2
3
Before tightening the center wire securing screw, make sure the center wire comes out
through the plug center opening.
4
English
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The peripheral devices (VCR, monitor, etc.) and cables are sold separately.
1
2
Adjust the picture on the monitor using the Brightness and Contrast controls.
: VIDEO IN
: VIDEO OUT
• Make sure the AC adaptor is not
connected to the wall outlet before
connecting it to the 24 V AC input
terminals.
(sold separately)
• When making the connections be careful
to respect the polarity and not to
shortcut the terminals.
VIDEO IN
VIDEO IN
VIDEO OUT
Time lapse VCR
(sold separately)
Monitor
(sold separately)
You can use multiple cameras by connecting them a camera switcher or a quad unit (sold
separately), then conducting the surveillance from one location by splitting the monitor screen to
view the image from each camera, or by switching the image from each camera on the monitor
screen. For detailed information, please refer to the installed devices instruction manuals.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
English
SETTINGS AND ADJUSTMENTS
Before taking the camera for repairs, please check below to make
sure that the camera is used correctly. If it still does not perform
correctly, please consult your dealer or a Sanyo Authorized Service
Center.
1
2
• Is the power turned on to all connected devices? Is the voltage
3
4
correct?
• Are all the signal connecting cables correctly connected?
• Is the lighting sufficient?
• Is the monitor correctly adjusted?
• Is the lens focus correctly adjusted?
• Are the lens surfaces clean?
If there is dust or finger prints on the lens, the image quality will
deteriorate. To clean the lens use a soft cloth or a commercially
available lens cleaning set.
This camera is a precision instruments and, if treated with care, it
will provide years of satisfactory performance. However, in the
event of a problem, the owner is advised not to attempt to make
repairs or open the cabinet. Servicing should always be referred to
your dealer or Sanyo Authorized Service Center.
English
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EIA standard (525 TV lines, 30
frames/sec.)
Temperature: –20˚C ∼ +60˚C
Humidity: less than 70% RH
525 TV lines, 60 field/sec.,
2:1 interlace
24 V AC
2.1 W
Interline transfer method, 1/3 inch
solid state CCD
Approx. 160 g
Features and specifications are subject to change without prior notice
or obligations.
537 (H) × 505 (V)
510 (H) × 492 (V)
Line lock
51 mm
400 TV lines horizontally, 350 TV
lines vertically
1.0 V(p-p)/75Ω (screw-on terminal)
More than 50 dB
0 lux
1/60 to 1/80,000 sec.
Electronic iris
Automatic
Built-in, F2.0, f=3.8 mm, fixed focal
lens, focus adjustment
Horizontally: Approx. 71˚
Vertically: Approx. 53˚
Diagonal: Approx. 90˚
Temperature: –10˚C ∼ +50˚C
Humidity: less than 90% RH
Download from Www.Somanuals.com. All Manuals Search And Download.
10
English
|