Network Supported
Multimedia Projector
❏
Wired LAN
Refer to the Owner's Manuals below for
details about network function.
MODEL PLC-XE34
❏
Network Set-up and Operation
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its respective
corporation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Before installing and operating this projector, read this
manual thoroughly.
Safety Precaution
This projector provides many convenient features and
functions. Operating the projector properly enables
you to manage those features and maintains it in good
condition for many years to come.
wARNING: ● THIS APPARATUS MUST BE EARTHED
● TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
Improper operation may result in not only shortening the
product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections
and try the solutions in the “Troubleshooting” section on
pages 64-66 of this manual. If the problem still persists,
contact the dealer where you purchased the projector or
the service center.
–This projector produces intense light from the projection
lens. Do not stare directly into the lens, otherwise eye
damage could result. Be especially careful that children
do not stare directly into the beam.
–Install the projector in a proper position. Otherwise it may
result in fire hazard.
–Allowing the proper amount of space on the top, sides,
and rear of the projector cabinet is critical for proper
air circulation and cooling of the unit. The dimension
shown here indicate the minimum space required.
If the projector is to be built into a compartment or
similarly enclosed, these minimum distances must be
maintained.
–Do not cover the ventilation slot on the projector. Heat
build-up can reduce the service life of your projector, and
can also be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK) NO USER-SERVICEABLE PARTS
INSIDE EXCEPT LAMP REPLACEMENT
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL
SIDE and TOP
REAR
0.7’(20cm)
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
1.5’(50cm)
3’(1m)
3’(1m)
THIS SYMBOL INDICATES THAT THERE ARE
IMPORTANT OPERATING AND MAINTENANCE
INSTRUCTIONS IN THE OWNER'S MANUAL
WITH THIS UNIT.
–If the projector is unused for an extended time, unplug
the projector from the power outlet.
–Do not project the same image for a long time. The
afterimage may remain on the LCD panels by the
characteristic of panel.
FOR EU USERS
The symbol mark and recycling systems described below
apply to EU countries and do not apply to countries in other
areas of the world.
CAUTION
Your product is designed and manufactured with high quality
materials and components which can be recycled and/or
reused.
DO NOT SET THE PROjECTOR IN GREASy, wET, OR
SMOKy CONDITIONS SUCH AS IN A KITCHEN TO PREVENT
A BREAKDOwN OR A DISASTER IF THE PROjECTOR
COMES IN CONTACT wITH OIL OR CHEMICALS, IT MAy
BECOME DETERIORATED
The symbol mark means that electrical and electronic
equipment, batteries and accumulators, at their end-of-
life, should be disposed of separately from your household
waste.
Note:
CAUTION
If a chemical symbol is printed beneath the symbol mark,
this chemical symbol means that the battery or accumulator
contains a heavy metal at a certain concentration. This will
be indicated as follows: Hg: mercury, Cd: cadmium, Pb: lead
Not for use in a computer room as defined in the Standard
for the Protection of Electronic Computer/Data Processing
Equipment, ANSI/NFPA 75.
In the European Union there are separate collection systems
for used electrical and electronic equipment,
batteries and accumulators.
Please, dispose of them correctly at your local
community waste collection/recycling centre.
Please, help us to conserve the environment
we live in!
READ AND KEEP THIS OwNER'S MANUAL FOR
LATER USE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read
Do not install the projector near the ventilation duct of
before the product is operated.
air-conditioning equipment.
Read all of the instructions given here and retain them
for later use. Unplug this projector from AC power supply
before cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
This projector should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supplied, consult your
authorized dealer or local power company.
Follow all warnings and instructions marked on the
projector.
Do not overload wall outlets and extension cords as this
can result in fire or electric shock. Do not allow anything
to rest on the power cord. Do not locate this projector
where the cord may be damaged by persons walking on
it.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will
prevent damage due to lightning and power line surges.
Do not attempt to service this projector yourself as
opening or removing Covers may expose you to
dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Unplug this projector from wall outlet and refer servicing
to qualified service personnel under the following
conditions:
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the projector to normal
operation.
Do not place this projector on an unstable cart, stand,
or table. The projector may fall, causing serious injury
to a child or adult, and serious damage to the projector.
Use only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or shelf
mounting should follow the manufacturer’s instructions,
and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
e. If the projector has been dropped or the cabinet has
been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the
service technician has used replacement parts specified
by the manufacturer that have the same characteristics
as the original part. Unauthorized substitutions may
result in fire, electric shock, or injury to persons.
Slots and openings in the back and bottom of the cabinet
are provided for ventilation, to ensure reliable operation of
the equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other
similar surface. This projector should never be placed
near or over a radiator or heat register.
Upon completion of any service or repairs to this
projector, ask the service technician to perform routine
safety checks to determine that the projector is in safe
operating condition.
NOTE FOR CUSTOMERS IN THE US
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the projector.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
Installing the Projector in Proper Position
Openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked
or covered.
Install the projector properly. Improper installation may
reduce the lamp life and cause a fire hazard.
Do not tilt the projector more than 20
20°
degrees from side to side.
20°
CAUTION
30°
Do not tilt the projector more than 30
Hot air is exhausted from the exhaust vent. When using
or installing the projector, the following precautions
should be taken.
degrees from above and below.
30°
– Do not put any flammable object or spray can near the
projector, hot air is exhausted from the air vents.
– Keep the exhaust vent at least 3’ (1 m) away from any
objects.
Do not point the projector up to project an
image.
– Do not touch a peripheral part of the exhaust vent,
especially screws and metallic parts. These areas will
become hot while the projector is being used.
– Do not put anything on the cabinet. Objects put on the
cabinet will not only get damaged but also may cause
fire hazard by heat.
Do not point the projector down to project
an image.
Do not put the projector on either side to
project an image.
Cooling fans are provided to cool down the projector.
The fans’ running speed is changed according to the
temperature inside the projector.
Moving the Projector
When moving the projector, replace the lens cap and
retract adjustable foot to prevent damage to the lens and
cabinet.
When the projector is not in use for an extended period,
put it into a suitable case.
Air Intake Vent
CAUTION IN CARRyING OR TRANSPORTING
THE PROjECTOR
– Do not drop or bump the projector, otherwise damages
or malfunctions may result.
– When carrying the projector, use a suitable carrying case.
– Do not transport the projector by courier or any other
transport service in an unsuitable transport case. This
may cause damage to the projector. For information
about transporting the projector by courier or any other
transport service, consult your dealer.
Air Intake Vent
Exhaust Vent
(Hot air exhaust)
– Do not put the projector in a case before the projector
is cooled enough.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communications Commission Notice
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If
such changes or modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: PLC-XE34
: Sanyo
: SANYO NORTH AMERICA CORPORATION
: 21605 Plummer Street, Chatsworth, California 91311
: (818)998-7322
Telephone No.
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the
GROUND
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin
face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the
ASA
same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a
replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug
(i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted.
wARNING : A PLUG wITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow Earth
Blue . . . . . . . . . . . Neutral
Brown . . . . . . . . . Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by
the letter E or by the safety earth symbol or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
wARNING: THIS APPARATUS MUST BE EARTHED
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILy ACCESSIBLE
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
① Top controls and Indicators
② Zoom Ring
Front
③ Focus Ring
②
③
①
④ Speaker
⑤ Infrared Remote Receiver
⑥ Projection Lens
⑦ Lens Cap
(See page 61 for attaching.)
CAUTION
Do not turn on a projector with lens cap attached. High
temperature from light beam may damage lens cap and
result in fire hazard.
⑧ Air Intake Vent
④
⑤
⑥
⑦
⑧
⑨ Lamp Cover
Back
⑩ Terminals and Connectors
⑪ LAN Connection Terminal
⑫ Power Cord Connector
⑬ Exhaust Vents
⑨
⑩
⑪
CAUTION
Hot air is exhausted from the exhaust vent. Do not put
heat-sensitive objects near this side.
⑭ Filters
⑮ Adjustable Foot
✽
⑫ ⑬
⑬
⑭
⑧
Bottom
⑭
⑮
Note:
✔
LAN Connection Terminal is for the Network function.
Refer to the owner’s manual of “Network Set-up and
Operation” .
⑪
✽ Kensington Security Slot
This slot is for a Kensington lock used to deter theft of
the projector.
*Kensington is a registered trademark of ACCO Brands
Corporation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Rear Terminal
①
②
③
⑤
⑥
⑦
⑧
④
① CONTROL PORT
⑤ VIDEO IN
When the projector is controlled by a computer,
connect to this jack with serial control cable.
Connect the composite video output signal to this
jack (p.15).
⑥ LAN Connection Terminal
② COMPUTER IN 1 /S-VIDEO IN / COMPONENT IN
Connect the LAN cable (refer to the owner’s
manual of “Network Set-up and Operation”).
Connect output signal from a computer, component
video output, RGB scart 21-pin video output or
S-video output to this terminal. (pp.14-16).
⑦ AUDIO IN（Video)
③ COMPUTER IN ꢀ / MONITOR OUT
Connect the audio output signal from video
equipment connected to ⑤ to this jack. For a mono
audio signal (a single audio jack), connect it to
L(MONO) jack. (pp.14-16).
– Connect analog RGB output signal from a
computer to this terminal (p.14).
– This terminal can be used to output the incoming
analog RGB and Component signal from
COMPUTER IN 1 /S-VIDEO IN /COMPONENT IN
terminal to the other monitor (pp.14,16).
⑧ AUDIO IN (PC)
Connect the audio output signal from computer
or video equipment connected to ② and ③ to this
jack. (pp.14-16).
④ AUDIO OUT (VARIABLE)
Connect an external audio amplifier to this jack
(pp.14-16).
This terminal outputs sound from AUDIO IN
terminal.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Top Control
⑤
⑧
⑦
④
③
②
①
⑥
① SELECT button
⑤ POwER indicator
–Execute the selected item (p.21).
–Expand or compress the image in the Digital
zoom mode (p.35).
–Lights red when the projector is in stand-by mode.
–Lights green during operations.
–Blinks green in the Power management mode
(p.50).
▲▼◄►
② POINT
(VOLUME +/–) buttons
⑥ MENU button
–Select an item or adjust the value in the
On-Screen Menu (p.21).
Open or close the On-Screen Menu (p.21).
–Pan the image in the Digital zoom +/- mode
(p.35).
–Adjust the volume level (Point ◄►buttons)
(p.24).
⑦ LAMP REPLACE indicator
Lights yellow when the projection lamp reaches its
end of life (pp.62, 70).
⑧ wARNING indicator
③ AUTO SETUP button
–Lights red when the projector detects an
abnormal condition.
–Blinks red when the internal temperature of the
projector exceeds the operating range (pp.59,
70).
Execute the setting of Auto setup (includes Input
search, Auto PC adj. and Auto Keystone functions)
in the setting menu. (pp.23, 44).
④ ON/STAND–By button
Turn the projector on or off (pp.18-20).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control
① ON/STAND-By button
Turn the projector on or off. (pp.18-20)
② AUTO SET button
Execute the setting of Auto setup (includes Input search, Auto PC adj.
and Auto Keystone functions) in the setting menu.
(pp.23, 44)
③ COMPUTER 1/ꢀ buttons
Select the COMPUTER 1 or COMPUTER 2 input source.
(pp.27, 37)
④ VIDEO button
Select the VIDEO input source. (p.36)
①
②
③
⑤ S-VIDEO button
Select the S-VIDEO input source. (p.36)
⑥ Point ▲▼◄►
buttons
– Select an item or adjust the value in the On-Screen Menu. (p.21)
– Pan the image in the Digital zoom +/- mode. (p.35)
⑳
⑲
④
⑤
⑦ SCREEN button
Select a screen mode. (pp.26, 34-35, 42)
⑥
⑦
⑧
⑧ MENU button
Open or close the On-Screen Menu. (p.21)
⑱
⑰
⑨ FREEZE button
Freeze the picture on the screen. (p.25)
⑩ NO SHOw button
⑨
⑯
⑮
⑭
Temporarily turn off the image on the screen. (p.26)
⑪ D ZOOM ▲▼ buttons
⑩
⑪
Zoom in and out the images. (pp.25, 35)
⑬
⑫ VOLUME +/- buttons
Adjust the volume level. (p.24)
⑫
⑬
MUTE button
Mute the sound. (p.24)
⑭ IMAGE button
Select the image mode. (pp.26, 32, 39)
⑮ P-TIMER button
Operate the P-timer function. (pp.26, 51)
⑯ LAMP button
Select a lamp mode. (pp.25, 53)
⑰ INFO button
Operate the information function. (p.58)
⑱ KEySTONE button
Correct keystone distortion. (pp.23, 45)
⑲ SELECT button
– Execute the selected item. (p.21)
– Expand or compress the image in Digital zoom mode. (p.35)
⑳ COMPONENT button
Select the COMPONENT input source. (p.37)
✔Note:
To ensure safe operation, please observe the following precautions:
– Do not bend, drop or expose the remote control to moisture or heat.
– For cleaning, use a soft dry cloth. Do not apply benzene, thinner, spray,
or any chemical material.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries
into the compartment.
Replace the
compartment lid.
1
ꢀ
3
Two AAA size batteries
For correct polarity
(+ and –), be sure
battery terminals are
in contact with pins in
compartment.
To ensure safe operation, please observe the following precautions :
● Use two (2) AAA or LR03 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Risk of an explosion if battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Remote Control Operating Range
Point the remote control toward the projector (Infrared
Remote Receiver) when pressing the buttons. Maximum
operating range for the remote control is about 16.4'(5 m)
and 60 degrees in front of the projector.
16.4'
(5 m)
30°
30°
Remote control
Remote Control Code
The 2 different remote control codes (Code 1–Code 2) are
assigned to this projector. Switching the remote
control codes prevents interference from other remote
controls when several projectors or video equipment
next to each other are operated at the same time. Change
the remote control code for the projector first before
changing that for the remote control. See "Remote control"
in the Setting Menu on page 53.
Press and hold the MENU and IMAGE buttons for more
than five seconds to switch between the Code 1 and Code
ꢀ. The initial code is set to Code 1.
MENU button
IMAGE button
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positioning the Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the
screen.
✔Note:
• The brightness in the room has a great influence on picture quality. It is recommended to limit ambient
lighting in order to obtain the best image.
• All measurements are approximate and may vary from the actual sizes.
38.7'(11.80m)
A : B = 6 : 1
(Inch Diagonal)
32.3'(9.84m)
300"(tele )
300"(wide)
21.5'(6.55m)
16.1'(4.90m)
10.7'(3.26m)
Max. Zoom
Min. Zoom
200"
167
250
150"
4.3'(1.30m)
A
100"
83
125
40"
(Center)
B
Screen Size
40”
100”
150”
200”
300”
(W x H) mm
813 x 610
2032 x 1524
3048 x 2286
4064 x 3048
6096 x 4572
4 : 3 aspect ratio
4.3'(1.30m)
5.1'(1.55m)
10.7'(3.26m)
12.9'(3.92m)
16.1'(4.90m)
19.4'(5.90m)
21.5'(6.55m)
25.8(7.87m)
32.3'(9.84m)
38.7'(11.80m)
Zoom (max)
Zoom (min)
Adjustable Foot
Projection angle can be adjusted up to 10.0 degrees with
the adjustable foot.
Lift the front of the projector and push the foot lock
latch on the projector.
Release the foot lock latch to lock the adjustable foot
and rotate the adjustable foot to adjust the position and
tilt.
To retract the adjustable foot, lift the front of the
projector and push and undo the foot lock latch.
Keystone distortion of the projected image can be
corrected by menu operation.(see pages 23, 44-45)
Foot Lock Latch
Adjustable Foot
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to a Computer
Cables used for connection
• VGA Cables (Mini D-sub 15 pin) *(Only one cable is supplied.)
• Audio Cables
(*One cable is supplied; other cables are not supplied with the projector.)
Monitor Input
or
Monitor Output
Audio Output
Monitor
Output
External Audio Equipment
VGA
VGA
cable
cable
Audio cable
Audio Input
(stereo)
COMPUTER IN 1
/ S-VIDEO IN
/COMPONENT IN
This terminal is switchable.
Set up the terminal as
either Computer input or
Monitor output. (See Page
49.)
COMPUTER IN 2 /
MONITOR OUT
Audio cable
(stereo)
AUDIO OUT
(stereo)
AUDIO IN
✔Note:
• Input sound to the AUDIO IN terminal when using the COMPUTER IN 1/ S-VIDEO IN / COMPONENT IN
and the COMPUTER IN 2/MONITOR OUT terminals as input.
• When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
• When the cable is of the longer variety, it is advisable to use the COMPUTER IN 1 /S-VIDEO IN /COMPONENT IN and
not the COMPUTER IN 2/MONITOR OUT.
Unplug the power cords of both the projector and external equipment from the AC outlet before connecting
cables.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Video Equipment
Cables used for connection
• Video Cable
• S-Video Cable
• S-Video-VGA Cable
• Audio Cables
(Cables are not supplied with the projector. )
S-Video Output and Audio output
Composite Video and Audio Output
External Audio Equipment
S-Video cable
Audio
cable
(stereo)
Audio
cable
Video cable
Audio Input
(stereo)
S-Video-VGA
cable
Audio cable
(stereo)
VIDEO IN
AUDIO IN
COMPUTER IN 1
/ S-VIDEO IN
AUDIO IN
/COMPONENT IN
AUDIO OUT
(stereo)
✔Note:
• When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
• See page 73 for ordering optional cables.
Unplug the power cords of both the projector and external equipment from the AC outlet before connecting
cables.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting to Component Video and RGB (Scart) Equipment
Cables used for connection
• Audio Cables
• Scart-VGA Cable
• Component Cable
• Component-VGA Cable
(Cables are not supplied with this projector.)
Audio Output
RGB Scart 21-
pin Output
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Component
cable
External Audio Equipment
Audio Input
Scart-VGA
cable
Audio cable
(stereo)
Component-
VGA cable
Audio cable
(stereo)
AUDIO OUT
(stereo)
COMPUTER IN 1/ S-VIDEO IN / COMPONENT IN
AUDIO IN
✔Note:
• When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
• See page 73 for ordering optional cables.
Unplug the power cords of both the projector and external equipment from the AC outlet before connecting
cables.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-240 V AC
and it automatically selects the correct input voltage. It is
designed to work with single-phase power systems having a
grounded neutral conductor. To reduce the risk of electrical
shock, do not plug into any other type of power system.
If you are not sure of the type of power being supplied,
consult your authorized dealer or service center.
Connect the projector with all peripheral equipment before
turning the projector on.
Connect the AC power cord (supplied) to the
projector.
CAUTION
The AC outlet must be near this equipment and must be
easily accessible.
✔Note:
Unplug the AC power cord when the projector is not
in use. When this projector is connected to an outlet
with the AC power cord, it is in Stand-by mode and
consumes a little electric power.
NOTE ON THE POwER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For Continental Europe
For the U K
For the U S A and Canada
Ground
Ground
To power cord
connector on your
projector.
To the AC outlet.
(ꢀ00 - ꢀ40 V AC)
To the AC outlet.
(ꢀ00 - ꢀ40 V AC)
To the AC outlet.
(1ꢀ0 V AC)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning On the Projector
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
1
ꢀ
16
Connect the projector’s AC power cord into an AC
outlet. The POWER indicator lights red. Open the lens
cap (see pages 8, 61).
Press the ON/STAND-BY button on the top control or
on the remote control. The POWER indicator lights
green and the cooling fans start to operate. The
preparation display appears on the screen and the
countdown starts.
3
The preparation display will disappear
after 30 seconds.
Selected Input Source and Lamp Control
Video
After the countdown, the input source that was selected
the last time and the lamp control status icon (see page
53) appear on the screen.
4
5
Lamp control status
(See page 53 for Lamp control status.)
✔Note:
If there is no signal input when start on the projector,
or the current signal is missed while operating the
projector, the Video/PC selection window will be
displayed on the screen, please move the pointer to
input source desired by pressing the Point ▲▼ buttons
and press the SELECT button. And then follow the
input signal guidance window to correct the signal and
connection.
The Filter warning and Lamp replacement
icons may appear on the screen
depending on the usage state of the
projector.
Video / PC selection window
Project Video
Project Video
If the projector is locked with a PIN code, PIN code input
dialog box will appear. Enter the PIN code as instructed
on the next page.
Project Computer
Cancel
Input signal guidance window
No signal
Current Input setting:Video
Is signal processed correctly?
Is cable connected properly?
Video / PC selection window
Project Video
Project Computer
✔Note:
• When the Logo select function is set to Off, the logo will
not be shown on the screen (p.46).
Cancel
• When Countdown off or Off is selected in the Display
function, the preparation display will not be shown on
the screen (p.45).
Input signal guidance window
• When the Input Search function is set to Onꢀ, the input
signal will be searched automatically (p.44).
No signal
Current Input setting:RGB
• When Off is selected in the Display function, the Video/
PC selection window and the input signal guidance
window are not shown on the screen. (p.45)
Is signal processed correctly?
Is cable connected properly?
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Enter a PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ◄ ► buttons to fix the number and move the red
frame pointer to the next box. The number changes to “✳”.
If you fixed an incorrect number, use the Point ◄ ► buttons
to move the pointer to the number you want to correct, and
then enter the correct number.
PIN Code Input Dialog Box
Repeat this step to complete entering a four-digit number.
After the OK icon disappears,
you can operate the projector.
After entering the four-digit number, move the pointer to Set.
Press the SELECT button so that you can start to operate
the projector.
If you entered an incorrect PIN code, PIN code and the
number (✳✳✳✳) will turn red for a moment. Enter the
correct PIN code all over again.
what is PIN code?
PIN (Personal Identification Number) code is a security
code that allows the person who knows it to operate the
projector. Setting a PIN code prevents unauthorized use of
the projector.
A PIN code consists of a four-digit number. Refer to the PIN
code lock function in the Setting Menu on pages 54-55 for
locking operation of the projector with your PIN code.
✔Note:
• If the PIN code number is not entered or wrong PIN
code number is entered within three minutes after the
PIN code dialog box appeared, the projector will be
turned off automatically.
• The “1234” is set as the initial PIN code at the factory.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take a special care in setting
a new PIN code, write down the number in a
column on page 76 of this manual and keep it
on hand. Should the PIN code be missing or
forgotten, consult your dealer or service center.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turning Off the Projector
Press the ON/STAND-BY button on the top control or
on the remote control, and Power off? appears on the
screen.
1
ꢀ
Press the ON/STAND-BY button again to turn off the
projector. The POWER indicator starts to blink red, and
the cooling fans keep running. (You can select the level
of fans’ quietness and speed. See “Fan” on page 56.)
At this time, you can unplug the AC power cord even if
the fans are still running.
Power off? disappears after 4 seconds.
When the projector has cooled down enough, the
POWER indicator stops blinking and you can turn on
the projector.
3
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST FIVE MINUTES BEFORE TURNING IT
OFF.
DO NOT OPERATE THE PROJECTOR
CONTINUOUSLY WITHOUT REST.
Direct OFF Function
CONTINUOUS USE MAY RESULT IN
SHORTENING THE LAMP LIFE. TURN OFF THE
PROJECTOR AND LET STAND FOR ABOUT AN
HOUR IN EVERY 24 HOURS.
You can disconnect the power cord from the
wall outlet or turn off the breaker even during
projection without pressing the on/stand-by
button.
✔Note:
✔Note:
• When the Direct on function is set to On, the projector
will be turned on automatically by connecting the AC
power cord to an AC outlet (p.50).
• The running speed of cooling fans is changed according
to the temperature inside the projector.
• When using the Direct OFF function, you
cannot restart the projector immediately
after the power is disconnected. If the
external power supply is suddenly cut
off, the fan stops immediately. The lamp
remains high temperature and needs to
be cooled.
• Do not put the projector in a case before the projector is
cooled enough.
• If the WARNING indicator blinks or lights red, see
“WARNING indicator” on page 59.
• While the POWER indicator is blinking, the lamp is being
cooled down and the projector cannot be turned on. Wait
until the POWER indicator stops blinking to turn on the
projector again.
• The fan rotation will terminate directly if the AC power
cord is unplugged immediately after the projector is
turned off.
• The projector can be turned on after the POWER
indicator turns red. The waiting time to restart will be
shortened when the normal power-off processing for fan
cooling is completed, compared with the time the AC
power cord is immediately unplugged after the power-
off.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Top Control
Menu. The menus have a hierarchical structure, with
a main menu that is divided into submenus, which are
further divided into other submenus. For each adjustment
and setting procedure, refer to respective sections in this
manual.
POINT buttons
(arrowhead)
Press the MENU button on the top control or the
1
remote control to display the On-Screen Menu.
SELECT button
Use the Point ▲▼ buttons to highlight or select a main
menu item. Press the Point ► or the SELECT button
to access the submenu items. (The selected item is
highlighted in orange.)
ꢀ
MENU button
Remote Control
POINT buttons
(arrowhead)
SELECT button
Use the Point ▲▼ buttons to select the desired
submenu item and press the SELECT button to set or
access the selected item.
3
MENU button
Use the Point ▲▼◄► buttons to adjust the setting or
4
switch between each option and press the SELECT
button to activate it and return to the submenu.
Press the Point ◄ button to return to the main menu.
Press the MENU button to exit the On-Screen Menu.
On-Screen Menu
5
Dynamic
Standard
Real
Blackboard(Green)
Colorboard
Image 1
Red
►
Image 2
Image 3
Image 4
Point
The currently set item is
check marked.
►
or SELECT
button
The selected item is
highlighted in orange.
Dynamic
Standard
Real
Blackboard(Green)
Colorboard
Image 1
►
Red
Image 2
Image 3
Image 4
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Bar
For detailed functions of each menu, see “Menu Tree” on pages 68-69.
Main Menu
Sub-Menu
Computer 1
Computer 2
Video
RGB
RGB
①
②
►
③
④
⑤
⑥
⑦
⑧
⑨
ƘƘƘ
⑩
① Input
Used to select an input source from Computer 1, Computer ꢀ or Video (pp.27, 36-37).
② PC adjust
Select Auto PC adj , Fine sync, Total dots, Horizontal, Vertical, Current mode, Clamp, Display area-H and Display
area-V to adjust the parameters to match with the PC input signal format (pp.29-31).
③ Image select
For computer source, used to select an image mode from among Dynamic, Standard, Real, Blackboard(Green),
Colorboard and image 1 - 4 (p.32).
For Video source, used to select an image mode among Dynamic, Standard, Cinema, Blackboard(Green), Colorboard
and Image 1- 4 (p.39).
④
⑤
Image adjust
For computer source, used to adjust computer image [Contrast, Brightness, Color temp , white balance (R/G/B),
Sharpness and Gamma] (pp.33-34).
For Video source, used to adjust picture image [Contrast, Brightness, Color, Tint, Color temp , white balance (R/G/
B), Sharpness, Gamma, Noise reduction and Progressive] (pp.40-41).
Screen
For computer source, used to adjust size of the image [ Normal, True, wide, Full, Custom, Custom adj. and Digital
zoom +/– ] (pp.34-35).
For Video source, used to set size of image [Normal, wide, Custom and Custom adj.] (p.42).
⑥ Sound
Used to adjust the volume or mute the sound (p.24).
⑦
Setting
Used to set the projector’s operating configurations (pp.43-57).
⑧ Information
Display the input source information: Input , H-sync freq , V-sync freq , Screen, Language, Lamp status, Lamp
counter , Power management, Key lock, PIN code lock and Remote control (p.58).
⑨ Network
See the owner’s manual of “Network Set-up and Operation”.
⑩ Guide
The key operation is displayed.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Zoom and Focus Adjustment
Rotate the Zoom Ring to zoom in and out.
Rotate the Focus Ring to adjust the focus of the image.
Zoom Ring
Focus Ring
Auto Setup Function
Auto setup function is provided to automatically execute the
setting of Auto setup (includes Input search, Auto PC adj.
and Auto Keystone functions) in the setting menu by just
pressing the AUTO SETUP button on the top control or the
AUTO SET button on the remote control. Refer to page 44
for the setting of the Auto setup function.
Top Control
AUTO SETUP button
✔Notes:
POINT ▲▼ buttons
• Auto Keystone corrects vertical distortion only; it does
not correct horizontal distortion.
• Auto Keystone cannot work when Ceiling feature is set
to On in the Setting menu (p.49).
• Perfect correction of the image distortion cannot be
ensured with the Auto setup function. If the distortion
cannot be corrected properly by pressing the AUTO
SETUP or AUTO SET button, adjust manually by
pressing the KEYSTONE button on the remote control
or selecting Keystone in the Setting menu (p.45).
• Fine sync, Total dots, Horizontal and Vertical
position of some computers cannot be fully adjusted
with the Auto PC Adjustment function. When the image
is not provided properly with this operation, manual
adjustments are required (pp.30-31).
Remote Control
AUTO SET button
POINT ▲▼ buttons
KEySTONE button
Keystone Correction
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control or the
AUTO SET button on the remote control, correct the image
manually as follows:
• The white arrows indicate that there is no
correction.
Press the KEYSTONE button on the remote control. The
Keystone dialog box appears. Use the Point ▲▼ buttons to
correct keystone distortion. The keystone adjustment can be
stored (see page 45).
• A red arrow indicates the direction of correction.
• An arrow disappears at the maximum correction.
• If you press the KEYSTONE button on the
remote control once more while the keystone
dialog box is being displayed, the keystone
adjustment will be canceled.
Reduce the upper width
Reduce the lower width
with the Point ▲ button.
with the Point ▼ button.
• The adjustable range is limited depending on the
input signal.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Sound Adjustment
Top Control
Direct Operation
VOLUME+/-
buttons
Volume
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Remote Control
Mute
Press the MUTE button on the remote control to select On
to temporarily turn off the sound. To turn the sound back
on, press the MUTE button again to select Off or press the
VOLUME +/– buttons. The Mute function is also effective for
the AUDIO OUT jack.
VOLUME+ button
MUTE button
VOLUME- button
Menu Operation
Press the MENU button to display the On-Screen Menu.
Use the Point ▲▼ buttons to select Sound. Press the
Point ► or the SELECT button to access the submenu
1
Approximate level
of the volume.
items.
Volume Dialog Box
Use the Point ▲▼ buttons to select the desired submenu
item and press the SELECT button to access the
selected item.
ꢀ
Press the MUTE button to set the
Mute function On or Off. The dialog
Volume
box disappears after 4 seconds.
Press the Point ► button to turn up the volume; press the
Point ◄ button to turn down the volume.
Sound Menu
Mute
Press the SELECT button to switch the mute function On/
Off. When the sound is turned off, On is displayed. Press
the VOLUME +/– buttons again to turn the sound back on.
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the On-Screen Menu.
COMPUTER 1/ꢀ, VIDEO, S-VIDEO and COMPONENT
buttons
Remote Control
COMPUTER 1/ꢀ
buttons
Press the COMPUTER 1/2, VIDEO, S-VIDEO and
COMPONENT buttons on the remote control to select the
input source. See pages 27, 36-37 for details.
S-VIDEO
button
COMPONENT
button
VIDEO
button
FREEZE button
Press the FREEZE button on the remote control to freeze
the picture on the screen, meanwhile, volume is muted. To
cancel the Freeze function, press the FREEZE button again
or press any other button.
Fig.1 will appear on the Screen menu while the Freeze
function is working.
INFO
button
FREEZE
button
LAMP
button
Fig.1
D ZOOM
buttons
INFO button
Display the input source information: Input, H-sync freq ,
V-sync freq , Screen, Language, Lamp status, Lamp
counter, Power management, Keylock, PIN code lock
and Remote control (p.58).
✔Note:
See the next page for the description of other
buttons.
D ZOOM buttons
Press the D.ZOOM buttons on the remote control to enter to
the Digital zoom +/– mode. See page 35 for details.
LAMP button
Press the LAMP button on the remote control to select the
lamp mode for changing the brightness on the screen.
High........... Brighter than the Normal mode.
Normal....... Normal brightness
Eco ............ Lower brightness reduces the lamp power
consumption and extends the lamp life.
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
NO SHOw button
Press the NO SHOW button on the remote control to black out
the image. To restore to normal, press the NO SHOW button
again or press any other button. When the projected image is
captured and is set as User in the Logo selection (p.47), the
screen changes each time you press the NO SHOW button as
follows.
No show disappears after 4 seconds.
• • • • •
black out → captured image → normal →
✔Note:
When use the MUTE button to release the No Show
function, the mute function can not be operated at the same
time.
P-TIMER button
Press the P-TIMER button on the remote control to operate
the Count up/Count down function. Refer to p.51 for detail of
Setting for the P-timer function.
To stop the count time, press the P-TIMER button.
To cancel the P-timer function, press and hold the P-TIMER
button.
0
P-Timer display
SCREEN button
IMAGE button
P-TIMER button
NO SHOw button
Press the IMAGE button on the remote control to select a
desired image mode of the screen. See pages 32, 39 for
details.
IMAGE button
SCREEN button
Select the screen size (See pages 34-35, 42 for details).
✔Note:
See the previous page for the description of
other buttons.
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Input Source Selection (RGB: Computer 1/Computer ꢀ)
Direct Operation
Choose either Computer 1(RGB) or Computer ꢀ(RGB) by pressing the COMPUTER 1 or COMPUTER 2 button
on the remote control.
Before using these buttons, correct input source should be selected through Menu operation as described
below.
Remote Control
COMPUTER 1 button
Computer 1(RGB)
Computer 1(Scart)
COMPUTER ꢀ button
Computer ꢀ (RGB)
Input Menu
Menu Operation
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
1
Use the Point ▲▼ buttons to select Computer 1.
ꢀ
When Computer 1 is selected, press the Point ►
button to access the submenu items. Use the Point ▲
▼ buttons to select the RGB input source and then
3
press the SELECT button.
Computer
1
►
Computer 1
RGB
Component
RGB(Scart)
S-video
✔Note:
When the Input Search function is set to On1 or Onꢀ in
the Auto setup function, the input signal will be searched
automatically (p.44).
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC
Adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format
and tunes to project a proper image without any additional settings. (Signal formats provided in this projector are
shown on page 71.)
One of the following messages may appear when:
When the projector cannot recognize the
connected signal conforming to the provided
Auto
PC System Menu
►
Computer 1
Computer 2
Video
RGB
RGB
PC systems, Auto is displayed on the System
Menu box and the Auto PC Adjustment function
works to display proper images. If the image is
not projected properly, a manual adjustment is
required (pp.30-31).
There is no signal input from the computer.
Check the connection between your computer
and the projector. (See “Troubleshooting” on
p.64.)
-----
System
XGA 1
►
The preset system is manually adjusted in the
PC adjust Menu. The adjusted data can be
stored in Mode 1–10 (pp.30-31).
Mode 1
SVGA 1
The PC System Menu
Selected system is
displayed.
PC Systems provided in this projector is chosen.
The projector chooses a proper system provided
in the projector and displays it.
*Mode 1 and SVGA 1 are examples.
Customized Mode
(1–10) set in the
PC adjust Menu
(pp.30-31).
Selecting Computer System Manually
PC system can also be selected manually.
PC System Menu
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
1
►
then press the Point or the SELECT button.
Use the Point ▲▼ buttons to select System and then
ꢀ
3
►
press the Point or the SELECT button.
Use the Point ▲▼ buttons to select the desired system
and then press the SELECT button.
Systems in this dialog box
can be selected.
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical
positions to conform to your computer.
PC adjust Menu
Menu Operation
Auto PC adj.
Fine sync
Total dots
Horizontal
Vertical
Current mode
Clamp
Display area H
Display area V
Reset
0
1365
0
Auto PC adj.
►
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select PC adjust
and then press the Point ► or the SELECT button.
0
1
0
1024
768
Mode free
Store
Use the Point ▲▼ buttons to select Auto PC adj. and
ꢀ
then press the SELECT button.
To store adjustment parameters
The adjusted parameters from the Auto PC Adjustment can
be stored in the projector. Once the parameters are stored,
the setting can be done just by selecting a Mode (1–10) in
the PC System Menu (see page 28). See also “Store” on
page 31.
Use Point ▲▼ buttons to select Auto PC
adj. and press the SELECT button.
Please wait... appears while the Auto PC
adjustment is in process.
Auto PC adj.
0
1365
0
Fine sync
Total dots
Horizontal
Vertical
►
✔Note:
0
Current mode
Clamp
Display area H
Display area V
Reset
Mode free
Store
• Fine sync, Total dots, Horizontal and Vertical
position of some computers cannot be fully adjusted
with the Auto PC Adjustment function. When the image
is not provided properly with this operation, manual
adjustments are required (pp.30-31).
0
1024
768
• The Auto PC Adjustment cannot be operated when 480i,
575i, 480p, 575p, 7ꢀ0p,1035i or 1080i is selected in the
PC System Menu (p.28).
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.
Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The
projector has five independent memory areas to store those parameters manually adjusted. It allows you to
recall the setting for a specific computer.
PC adjust Menu
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select PC adjust
and then press the Point ► or the SELECT button.
1
ꢀ
Auto PC adj.
Fine sync
Total dots
Horizontal
Vertical
0
1365
0
►
0
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to
adjust the setting value.
Current mode
Clamp
Display area H
Display area V
Reset
0
1024
768
Mode free
Store
Fine sync
Use the Point ◄► buttons to adjust the value, eliminating a
flicker from the image displayed (from 0 to 31).
Total dots
Auto PC adj.
Fine sync
Total dots
Horizontal
Vertical
Current mode
Clamp
Display area H
Display area V
Reset
0
►
1365
0
0
Use the Point ◄► buttons to adjust the number of total dots
in one horizontal period to match your PC image.
0
1024
768
Horizontal
Mode free
Store
Use the Point ◄► buttons to adjust the horizontal picture
position.
Vertical
Use the Point ◄► buttons to adjust the vertical picture
position.
►
Current mode
Press the SELECT button to show H-sync freq. and V-sync
freq. of the connected computer.
Clamp
Use the Point ◄► buttons to adjust the clamp level. When
the image has dark bars, try this adjustment.
Display area H
Use the Point ◄► buttons to adjust the horizontal area
displayed by this projector.
Display area V
Use the Point ◄► buttons to adjust the vertical area
displayed by this projector.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
yes. All adjustments will return to their previous figures.
Mode free
Auto PC adj.
Fine sync
Total dots
Horiznotal
Vertical
0
1365
0
►
0
Current mode
Clamp
Display area H
Display area V
Reset
0
1024
768
Mode free
Mode free
Store
►
To clear the stored data, select Mode free and then press
the Point ► or the SELECT button. Move the highlight to the
Mode that you want to clear and then press the SELECT
button.
This Mode has stored
parameters.
Store
Where to free?
To store the adjusted data, select Store and then press the
Point ► or the SELECT button. Move the highlight to one
of the Modes 1 to 10 in which you want to store, and then
press the SELECT button.
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
►
Total dots
Horizontal
Vertical
1344
0
255
304
1024
768
Display area H
Display area V
Values of Total dots, Horizontal,
Vertical, Display area H, and
Display area V.
Vacant
Store
Store
Where to store?
store?
Free
►
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Total dots
Total dots
1344
0
Position H
0
Horizontal
255
0
Position V
Vertical
304
Display area H
Display area H
1024
768
Display area V
Display area V
Press MENU button
to close this dialog
box.
Press SELECT button to
store the data.
✔Note:
• Display area (H/V) cannot be selected when 480i, 575i, 480p, 575p, 7ꢀ0p, 1035i or 1080i is selected in the
PC System Menu (p.28).
• When input computer signal to the projector, PC adjust will become available.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Mode Selection
Direct Operation
Remote Control
IMAGE button
Dynamic
Select the desired image mode among Dynamic, Standard,
Real, Blackboard (Green), Colorboard, Image 1, Image ꢀ,
Image 3 and Image 4 by pressing the IMAGE button on the
remote control.
Standard
Real
(Green)
Blackboard
IMAGE button
Colorboard
Image 1
Image ꢀ
Image 3
Menu Operation
Press the MENU button to display the On-Screen Menu.
Use the Point ▲▼ buttons to select Image select and
1
then press the Point ► or the SELECT button.
Image 4
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button.
ꢀ
Dynamic
For viewing pictures in a bright room.
Image select Menu
Standard
Normal picture mode preset on the projector.
Real
Picture mode with improved halftone for graphics.
Blackboard (Green)
For the image projected on a blackboard.
This mode helps enhance the image projected on a
blackboard. This is mainly effective on a green colored
board, not truly effective on a black colored board.
Colorboard
Dynamic
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Standard
Real
Blackboard(Green)
Colorboard
Image 1
►
Red
Image 2
Image 3
Image 4
Image 1–4
For viewing with the user preset image mode in the Image
Adjust Menu (see pages 33-34). This Image memory is
provided in each computer, component, S-video and video
input source.
3ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Image Adjustment
Press the MENU button to display the On-Screen
Image Adjust Menu
1
ꢀ
Menu. Use the Point ▲▼ buttons to select Image
adjust and then press the Point ►or the SELECT
button.
Use the Point ▲▼ buttons select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to
adjust the setting value.
Contrast
Press the Point ◄ button to decrease the contrast; press the
Point ►button to increase the contrast (from 0 to 63).
Brightness
Selected Image mode
Press the Point ◄ button to decrease the brightness; press
the Point ►button to increase the brightness (from 0 to 63).
Color temp.
Use the Point ◄► buttons to select the desired Color temp.
level (XLow, Low, Mid, or High).
white balance (Red)
Press the Point◄ button to lighten red tone; press the Point
► button to deepen red tone (from 0 to 63).
Use the Point ◄►
buttons to adjust the
setting value.
white balance (Green)
Press the Point ◄ button to lighten green tone; press the
Point ► button to deepen green tone (from 0 to 63).
white balance (Blue)
Press the Point ◄ button to lighten blue tone; press the
Point ► button to deepen blue tone (from 0 to 63).
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to
✔Note:
obtain a better balance of contrast (from 0 to 15).
• When White balance Red, Green or Blue is
adjusted, Color temp. will change to User.
• When Blackboard(Green) or Colorboard
is selected in Image select, Color temp. will
change to Blackboard or Colorboard.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
yes. All adjustments will return to their previous figures.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Where to store?
Store
Image 1
Image 2
Image 3
Image 4
To store the adjusted data, select Store and press the Point
►
►or the SELECT button. Use the Point ▲▼ buttons to
select one from Image 1 to 4 and press the SELECT button.
A confirmation box appears and then select yes. Stored
data can be called up by selecting an Image (1–4) in the
Image Mode Selection on page 32.
Screen Size Adjustment
This projector has the picture screen resize function, which
enables you to customize the image size.
A confirmation box appears and
then select yes.
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Screen and
then press the Point ► or the SELECT button.
1
Use the Point ▲▼ buttons select the desired item and
then press the SELECT button .
ꢀ
Screen Menu
Normal
True
Wide
Full
Normal
Custom
Custom adj.
Digital zoom +
Provide the image to fit the screen size.
True
►
Digital zoom -
Provide the image in its original size. When the original
image size is larger or smaller than the screen size
(1024 x 768), the projector enters to the panning mode
automatically. Use the Point ▲▼◄► buttons to pan the
image. When adjusted, the arrows will turn red. When
reached to the correction limits, the arrows will disappear.
wide
Normal
True
Provide the image to fit the wide video aspect ratio (16:9) by
expanding the image width uniformly. This function can be
used for providing a squeezed video signal at 16:9.
Full
Wide
Custom
Custom adj.
Digital zoom +
Digital zoom -
►
Full
Provide the full screen image.
Custom
Provide the last stored aspect screen image.
✔Note:
• The Screen Menu, only Normal and Custom can be operated, wide will be disabled and displayed in gray
when 7ꢀ0p, 1035i, or 1080i is selected in the PC System Menu (p.28).
• This projector cannot display any resolution higher than 1920 x 1200. If your computer’s screen resolution is
higher than it, reset the resolution to the lower before connecting to the projector.
• The image data in other than 1024 x 768 is modified to fit the screen size in initial mode.
• True, Full, and Digital zoom +/– are disabled and cannot be displayed when 480i, 575i, 480p or 575p is
selected in the PC System Menu (p.28).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Custom adj.
adj.
Adjust the screen scale and position manually with this
function.
►
Press the Point button at Custom adj. and the Custom
adjustment menu is displayed on the screen, you can use
the Point ▲▼ buttons to choose the item you want to adjust.
►
Scale H/V.......... Adjust the Horizontal/Vertical screen
scale.
H&V................... When set to On, the aspect ratio is
fixed. The Scale V appears dimmed and
becomes unavailable. Adjust Scale H,
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V ..... Adjust the Horizontal/Vertical screen
position.
Common........... Save the adjusted scale or position to all
the inputs. Press the SELECT button at
Common to display a confirmation box.
To save the scale or position, press the
SELECT button at yes. When Custom
is selected, the saved scale or position is
used.
Reset................. Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at yes.
✔Note:
• When no signal is detected, Normal is set
automatically .
• The adjustable range for Scale H/V and
Position H/V is limited depending on the
input signal.
Remote Control
POINT buttons
For zooming in and out the images
Digital zoom +
SELECT button
Select Digital zoom +. The On-Screen Menu disappears and
D. zoom + appears. Press the SELECT button to expand the
image size. Use the Point ▲▼◄► buttons to pan the image.
The Panning function can work only when the image is larger
than the screen size.
D.ZOOM + button
D.ZOOM - button
A projected image can be also expanded by pressing the
D.ZOOM ▲ or the SELECT button on the remote control.
✔Note:
Digital zoom –
• The minimum compression ratio is limited
depending on the input signal, when the
Keystone function is working or when the
custom is selected for the screen size.
• True, Full, and Digital zoom +/– cannot
be selected when 480i, 575i, 480p or
575p is selected in the PC System Menu
(p.28).
• Digital zoom +/- cannot be selected
when Full or True is selected.
• When Custom is selected, the Digital
zoom - function is disabled.
Select Digital zoom –. The On-Screen Menu disappears and
D. zoom – appears. Press the SELECT button to compress
image size.
The projected image can be also compressed by pressing the
D.ZOOM ▼ or the SELECT button on the remote control.
To exit the Digital zoom +/– mode, press any button except
the D.ZOOM ▲▼ buttons, SELECT and Point buttons.
To return to the previous screen size, select a screen size
from the Screen Size Adjustment Menu or select an input
source from the Input Source Selection Menu (see page
27) again, or adjust the screen size with the D.ZOOM ▲▼
buttons.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Video, S-video)
Direct Operation
Remote Control
Choose Video or S-video by pressing the VIDEO or the S-
VIDEO button on the remote control.
VIDEO button
Video
Before using these buttons, correct input source should be
selected through menu operation as described below.
S-VIDEO button
S-video
Menu Operation
Input Menu
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
1
►
then press the Point or the SELECT button.
Use the Point ▲▼buttons to select Video and then
press the SELECT button.
ꢀ
When video input signal is connected to the
VIDEO jack, select Video.
Video
Auto
Use the Point ▲▼ buttons to select Computer 1. And then
press the Point ► button to access the submenu items. Use
the Point ▲▼ buttons to select the S-video and then press
the SELECT button.
When the input source is coming from video
S-video
equipment connected to the COMPUTER IN
1/S-VIDEO IN/COMPONENT IN terminal with a
S-video-VGA cable, select S-VIDEO.
Auto
✔Note:
When the Input Search function is set to On1 or Onꢀ in
the Auto setup function, the input signal will be searched
automatically (p.44).
Computer
1
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Component, RGB Scart ꢀ1-pin)
Direct Operation
Choose Computer 1(Component) or Computer 1(Scart) by pressing the COMPONENT or the COMPUTER 1
button on the remote control.
Before using these buttons, correct input source should be selected through Menu operation as described
below.
Remote Control
COMPUTER 1 button
Computer 1(RGB)
Computer 1(Scart)
COMPONENT button
Computer 1(Component)
Input Menu
Menu Operation
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
1
Use the Point ▲▼ buttons to select Computer 1 and
then press the Point ► button.
ꢀ
3
Use the Point ▲▼ buttons to select Component or
RGB(Scart) and then press the SELECT button.
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/S-VIDEO IN/COMPONENT IN terminal
with a Component-VGA Cable, select
Component.
Component
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/S-VIDEO IN/COMPONENT IN terminal
with a Scart-VGA Cable, select RGB
(Scart).
RGB (Scart)
S-video
✔Note:
When the Input Search function is set to On1 or Onꢀ,
the input signal will be searched automatically (p.44).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Video System Selection
AV System Menu (Video or S-video)
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
1
►
then press the Point or the SELECT button.
Select Video, S-video or Computer 1(Component)
input source. (See pages 36-37)
ꢀ
3
Use the Point ▲▼ buttons to select System and then
►
press the Point or the SELECT button. Use the Point
▲▼ buttons to select the desired system and then
press the SELECT button.
Video or S-video
Auto
The projector automatically detects an incoming video
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system
manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector cannot reproduce proper video image,
select a specific broadcast signal format from among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Component
AV System Menu (Component)
Auto
The projector automatically detects an incoming video
signal, and adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select
a specific component video signal format from among 480i,
575i, 480p, 575p, 7ꢀ0p, 1035i, and 1080i.
►
✔Note:
The AV System Menu cannot be selected when selecting
RGB (Scart).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Mode Selection
IMAGE button
Remote Control
Direct Operation
Dynamic
Select the desired image mode among Dynamic, Standard,
Cinema, Blackboard (Green), Colorboard, Image 1,
Image ꢀ, Image 3 and Image 4 by pressing the IMAGE
button on the remote control.
Standard
Cinema
Menu Operation
Blackboard (Green)
Press the MENU button to display the On-Screen Menu.
Use the Point ▲▼ buttons to select Image select and
1
Colorboard
IMAGE button
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button .
Image 1
Image ꢀ
Image 3
ꢀ
Image 4
Dynamic
For viewing pictures in a bright room.
Image select Menu
Standard
Normal picture mode preset on the projector.
Cinema
Picture mode adjusted with fine tone.
Blackboard (Green)
For the image projected on a blackboard.
This mode help enhance the image projected on a
blackboard. This is mainly effective on a green colored
board, not truly effective on a black colored board.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
►
Image 1–4
For viewing with the user preset image mode in the Image
Adjust Menu (see pages 40-41). This Image memory is
provided in each computer, scart, component, S-video and
video input source.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Image Adjustment
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Image
adjust and then press the Point ► or the SELECT
button.
Image Adjust Menu
1
ꢀ
Use the Point ▲▼ buttons select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to
adjust the setting value.
Contrast
Press the Point ◄ button to decrease the contrast; press the
Point ► button to increase the contrast (from 0 to 63).
Selected Image mode
Brightness
Press the Point ◄ button to decrease the brightness; press
the Point ► button to increase the brightness (from 0 to 63).
Color
Press the Point ◄ button decrease the intensity of the color;
press the Point ► button increase the intensity of the color
(from 0 to 63).
Tint
Use the Point ◄►
buttons to adjust the
setting value.
Press the Point ◄► buttons to adjust the tint value to get a
proper color balance (from 0 to 63).
Color temp.
Use the Point ◄► buttons to select the desired Color temp.
level (High, Mid, Low, or XLow).
white balance (Red)
Press the Point ◄ button to lighten red tone; press the Point
► button to deepen red tone (from 0 to 63).
white balance (Green)
Press the Point ◄ button to lighten green tone; press the
Point ► button to deepen green tone (from 0 to 63).
white balance (Blue)
Press the Point ◄ button to lighten blue tone; press the
Point ► button to deepen blue tone (from 0 to 63).
✔Note:
• When the white balance Red, Green or Blue is adjusted, the Color temp. level will change to User.
• Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.38).
• When Blackboard(Green) or Colorboard is selected in Image select, Color temp. will change to
Blackboard or Colorboard.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to
obtain a better balance of contrast (from 0 to 15).
Noise reduction
Noise interference on the screen can be reduced. Select
one of the following options to get smoother images.
Off ......... Disabled.
L1 .......... Lower reduction
Lꢀ .......... Higher reduction
Progressive
An interlaced video signal can be displayed in progressive
mode. Select one of the following options.
Off ......... Disabled.
L1 .......... For an active picture.
Lꢀ .......... For a still picture.
Film....... For watching a film. With this function, the
projector reproduces pictures faithful to the
original film quality.
Store Menu
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
yes. All adjustments will return to their previous figures.
Store
To store the adjusted data, select Store and press the Point
► or the SELECT button. Use the Point ▲▼ buttons to
select one from Image 1 to 4 and press the SELECT button.
A confirmation box appears and then select yes. Stored
data can be called up by selecting an Image (1–4) in the
Image Mode Selection on page 39.
A confirmation box
appears and then
select yes.
✔Note:
Noise reduction and Progressive cannot be selected
when 480p, 575p, 7ꢀ0p, 1035i or 1080i is selected
(p.38).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Screen Size Adjustment
This projector has the picture screen resize function, which enables you to customize the image size.
Screen Menu
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Screen and
1
then press the Point ► or the SELECT button.
►
Use the Point ▲▼ buttons select the desired item and
then press the SELECT button.
ꢀ
►
Normal
Provide the image to fit the screen size while maintaining
the aspect ratio of the input signal.
wide
Modify the 4:3 aspect ratio image to fit the screen size (16:9
aspect ratio) by streching the image.
Custom
Provide the last stored aspect screen image.
Custom adj.
►
Adjust the screen scale and position manually with this
function.
►
Press the Point button at Custom adj. and the Custom
adjustment menu is displayed on the screen, you can use
the Point ▲▼ buttons to choose the item you want to adjust.
Scale H/V.......... Adjust the Horizontal/Vertical screen
scale.
H&V................... When set to On, the aspect ratio is
fixed. The Scale V appears dimmed and
becomes unavailable. Adjust Scale H,
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V ..... Adjust the Horizontal/Vertical screen
position.
Common........... Save the adjusted scale or position to all
the inputs. Press the SELECT button at
Common to display a confirmation box.
To save the scale or position, press the
SELECT button at yes. When Custom
is selected, the saved scale or position is
used.
Reset................. Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at yes.
✔Note:
• When no signal is detected, Normal is set
automatically.
• The adjustable range for Scale H/V and
Position H/V is limited depending on the
input signal.
• wide cannot be operated when 7ꢀ0p,
1035i or 1080i is selected in the AV
System Menu (p.38).
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Setting
This projector has a Setting menu that allows you to set up
the other various functions described below.
Setting Menu
Press the MENU button to display the On-Screen
Menu. Press the Point ▲▼ buttons to select Setting
and press the Point ► or the SELECT button to access
1
the submenu items.
Use the Point ▲▼ buttons to select the desired item
and then press the Point ► or the SELECT button to
access the selected item.
ꢀ
Use the Point ▲▼ buttons select the desired item and
then press the SELECT button.
3
Language
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Russian,Turkish, Kazakh, Vietnamese, Chinese, Korean,
japanese and Thai.
Menu position
This function is used to change the position of the
On-Screen Menu. Select Menu position and press the
SELECT button.
The Menu position changes each time you press SELECT
button as follows.
the top left → the top right → the center → the bottom left
→ the bottom right → the top left →.....
►
1/2
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Auto setup
Auto setup
English
This function enables Input search, Auto Keystone correction
and Auto PC adjustment by pressing the AUTO SETUP button
on the top control or the AUTO SET button on the remote
control. Settings for those functions can be altered as follows:
Input search
►
Blue
On
Off
Off
This function detects the input signal automatically. When
a signal is found, the search will stop. Use the Point ▲▼
buttons to select one of the following options.
Off ........... Input search does not work.
On1.......... Input search works under the following situation.
– When pressing the AUTO SETUP button on
the top control.
– When pressing the AUTO SET button on the
remote control.
Onꢀ.......... Input search works under the following situation.
– When turning on the projector by pressing the
ON/STAND-BY button on the top control or the
remote control.
Computer 2
►
►
►
Off
Off
Network
Direct on
1/2
On 1
On
Auto PC adj.
Auto Keystone
Auto
– When pressing the AUTO SET button on the
remote control.
– When pressing the AUTO SETUP button on
the top control.
– When the current input signal is cut off.*
* If the No show or Freeze function is active, cancel it to
activate the Input search. It is also unavailable when On-
Screen menu is displayed.
On 1
On
Auto
Auto PC adj.
On. . . . . . . .Enables Auto PC Adjustment when pressing
the AUTO SET button on the remote control or
the AUTO SETUP button on the top control.
Off . . . . . . .Disables Auto PC Adjustment.
Auto Keystone
Auto . . . . . Always works and corrects keystone distortion
according to the projector's tilt.
✔Note:
Manual . . . .Works only when pressing the AUTO SETUP
button on the top control or the AUTO SET
button on the remote control.
• Auto Keystone corrects vertical distortion only,
not correct horizontal distortion.
• The Auto Keystone function cannot work when
the Ceiling feature is set On in the Setting menu
(p.49).
Off . . . . . . .Disables Auto Keystone.
• Perfect correction of the image distortion cannot
be ensured with the Auto setup function. If the
✔Note:
• While Input search is set to On1 or Onꢀ, the status of Input
and Lamp are displayed every time the signal is switched.
• Only the last selected input source can be detected.
• During Input search is in progress, If the MENU button or the
ON/STAND-BY button is pressed, Input search will stop. If
the COMPUTER 1/2 button or VIDEO or COMPONENT or S-
VIDEO button is pressed, Input search will stop and go back
to the button's input signal.
distortion is not corrected properly by pressing the
AUTO SETUP or the AUTO SET button, adjust
manually by pressing the KEYSTONE button on
the remote control or selecting Keystone in the
Setting menu (pp.23, 45).
• Fine sync, Total dots, Horizontal and Vertical
position of some computers cannot be fully
adjusted with the Auto PC Adjustment function.
When the image is not provided properly with
this operation, manual adjustments are required
(pp.30-31).
• Input search, Auto PC adj. and Auto Keystone cannot be
set Off at the same time.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Keystone
This function is used to adjust keystone distortion of the
projected image. Use the Point ▲▼ buttons to choose the
item you want to adjust.
Keystone
English
Keystone
►
To correct keystone distortion, press the SELECT button.
Keystone appears on the screen. Use the Point ▲▼
buttons to correct keystone distortion (p.23).
Store
Store .....Keep the keystone correction even when the AC
power cord is unplugged.
Blue
On
Off
Off
Computer 2
►
OfOf ff
Off
Direct on
Network
Reset.....Release the keystone correction when the AC
power cord is unplugged.
1/2
Background
Keystone
Store
Select the background screen for when no input signal is
Store
▲▼
detected. Press the Point
each option.
buttons to switch between
Blue . . . Project a blue background.
User . . . Project an image captured in the Logo setting.
Black . . Project a black background.
►
Display
This function decides whether to display On-Screen
Displays.
On ........................... Show all the On-Screen displays. Use
this function when you want to project
images after the lamp becomes bright
enough. The factory default setting is
in this option.
Countdown Off....... Show the input image instead of
the countdown when turning on the
projector. Use this function when you
want to project the image as early as
possible even when the lamp is not
bright enough.
Off ........................... Hide the On-Screen Displays except;
● On-Screen Menu.
● Power off? (p.20)
● P-Timer display. (p.26)
● No signal for Power management
(p.50)
● Please wait ...
● Arrows for the True function in the
Screen Menu. (p.34)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo (Logo and Logo PIN code lock settings)
Logo select
This function allows you to customize the screen logo with
Logo select, capture, Logo PIN code lock and Logo PIN
code change functions.
English
Store
Blue
On
✔Note:
►
Off
When On is selected in the Logo PIN code lock function,
Off
Logo select and Capture functions cannot be selected.
Computer 2
►
Off
Off
Direct on
Network
1/2
Logo select
This function decides on the starting-up display from
among following options.
User ........ Show the image you captured.
Default .... Show the factory-set logo.
Off ........... Show the countdown display only.
Default
Off
Off
►
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Capture
This function enables you to capture an image being
projected to use it for a starting-up display or interval of
presentations.
Capture
Off
Off
Select Capture and press the SELECT button.
A confirmation box appears and select yes to capture the
projected image.
►
After capturing the projected image, go to the Logo select
function and set it to User. Then the captured image will be
displayed the next time you turn on the projector or when
you press the NO SHOW button. (see page 26)
Start
Move
To cancel the capture function, select yes in the "Quit?"
confirmation box.
✔Note:
• Before capturing an image, select Standard in the
Image select Menu to capture a proper image (pp.32,
39).
• A signal from a computer can be captured up to XGA
(1024 x 768). A signal from video equipment can be
captured except for 720p, 1035i, and 1080i.
• When capturing the image that has been adjusted by
the Keystone function, the adjusted data is automatically
reset and the projector captures an image without
keystone correction.
Quit?
• When Logo PIN code lock is set to On, capture cannot
be selected.
• When starting to capture a new image, the previously
stored image is cleared even if you cancel the capturing.
• When there is no captured image or it is interrupted
while capturing an image, User cannot be selected, you
can only switch between Default and Off.
Logo PIN code lock
Logo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
Off
Off
Off ........... The screen logo can be changed freely from
the Logo Menu (p.46).
On ........... The screen logo cannot be changed without a
Logo PIN code.
►
If you want to change the Logo PIN code lock setting,
press the SELECT button and the Logo PIN code dialog
box appears. Enter a Logo PIN code by following the steps
below. The initial Logo PIN code is set to “4321” at the
factory.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Enter a Logo PIN code
Enter a Logo PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ◄► buttons to fix the number and move the red
frame pointer to the next box. The number changes to
✳. If you fixed an incorrect number, use the Point ◄►
buttons to move the pointer to the number you want to
correct, and then enter the correct number.
Logo PIN code
After a correct Logo PIN code
is entered, the following dialog
box appears.
Repeat this step to complete entering a four-digit
number.
Change the Logo PIN code lock setting
After entering the four-digit number, move the pointer to
Set. Press the SELECT button so that you can start to
operate the projector.
Off
If you entered an incorrect Logo PIN code, Logo
PIN code and the number (✳✳✳✳) will turn red for a
moment. Enter the correct Logo PIN code all over again.
►
Select
Change the Logo PIN code lock setting
Use the Point ▲▼ buttons to switch On or Off, and then
press the SELECT button to make a chioce.
Change the Logo PIN code
Off
Logo PIN code change
►
Logo PIN code can be changed to your desired four-
digit number. Press the SELECT button to select Logo
PIN code change. Current Logo PIN code dialog box
appears, use the Point ▲▼buttons to enter the correct
code. The New Logo PIN code input dialog box appears.
Set a new Logo PIN code, confirmation box appears,
choose yes to set the new Logo PIN code.
Next
Current Logo PIN code
Be sure to note the new Logo PIN code and keep it on
hand. If you lost the number, you could no longer change
the Logo PIN code setting.
CAUTION:
wHEN yOU HAVE CHANGED THE LOGO PIN CODE,
wRITE DOwN THE NEw PIN CODE IN COLUMN OF
THE LOGO PIN CODE NO. MEMO ON PAGE 76 , AND
KEEP IT SECURELy. SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE LOGO PIN CODE
SETTING CAN NO LONGER BE CHANGED.
----
Exit
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Ceiling
Ceiling
When this function is set to On, the picture will be top/
bottom and left/right reversed. This function is used to
project the image from a ceiling-mounted projector.
Rear
When this function is set to On, the picture will be left/right
reversed. This function is used to project the image from
rear of the screen.
Rear
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back
of the projector is switchable for computer input or monitor
output. (See page 9) Select Computer ꢀ or Monitor Out
▲▼
Terminal
with the Point
buttons.
Computer ꢀ . . computer input
Monitor Out. . monitor out
Terminal function is not available when selecting Computer
ꢀ to the input source. Change the input source to the others
(Computer 1, and so on) so that the Terminal function will
be available. (p.25, 36, 37)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Power management
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not operated for a
certain period.
Time left before Lamp is off.
Select one of the following options:
Ready............... When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition,
English
Blue
On
the projection lamp will be turned on if
the input signal is reconnected or any
button on the top control or remote
control is pressed.
Off
Off
Computer 2
►
Off
On
►
Direct on
Shut down....... When the lamp has been fully cooled
down, the power will be turned off.
Network
1/2
Off .................... Power management function is off.
Timer................ If the input signal is interrupted and
no button is pressed for more than
30 seconds, the timer display with
No signal appears. It starts the
countdown until the lamp is turned off.
Use the Point ▲▼ buttons to set the
Timer(1~30min).
Off
✔Note:
Factory default is Ready: 5 min.
ꢀ
Direct on
When this function is set to On, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
✔Note:
• Be sure to turn off the projector properly (see “Turning Off
the Projector” on page 20). If the projector is turned off in
the incorrect sequence, the Direct on function will not
work properly.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Standby mode
This function is available when operating the projector via
network.
Network .... Supply the power to the network function even
after turning off the projector by pressing the
ON/STAND-BY button on the remote control.
You can turn on/off the projector via network,
modify network environment, and receive
an e-mail about projector status while the
projector is powered off.
P-TIMER
Eco............ Select Eco when you do not use the projector
via network. The projector’s network function
will stop when turning off the projector, you
can not turn on the projector via network.
0
P-timer display
Refer to the owner’s manual of “Network Set-up and
Operation”.
✔Note:
• When selecting Network, the cooling fans may be
running depending on the temperature inside the
projector even if the projector is turned off.
• When Eco mode is selected and the projector is in Stand-
by, the communication of RS-232C serial port is not
available.
P-timer
This function allows you to change the setting of the P-timer and
execute it.
Select one of the following options:
Start
Reset
Exit
Count up ............. The P-timer display 000:00 appears on the
screen and the count starts (000:00–180:00)
Count down......... The time set in the Timer setting appears on
the screen and the countdown starts.
Timer.................... Use the Point ▲▼ buttons to set the Timer
(1–180 Min). Timer is available in Count
down only. Factory default velue is 10 Min.
Start..................... It executes the count up or count down
function. Press the SELECT button at
Start and the indication changes into
Stop. To stop Count up or Count down,
press the SELECT button at Stop on the
screen menu,then the indication changes
into Restart. Press the SELECT button
at Restart to resume Count up or Count
down.
Reset ................... Reset the P-timer values.
Press the SELECT button at Reset to return
to the following value;
Count up ... "000:00"
Count down ... Timer that you set
Exit....................... To exit the P-timer operation.
Stop or Cancel the P-timer via Remote Control
To stop the P-timer, press the P-TIMER button.
To cancel the P-timer, press and hold the P-TIMER
button for a few seconds.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Closed Caption
Closed Caption
Closed Caption is a printed version of the program sound or
other information displayed on the screen. If the input signal
contains closed captions, you can turn on the feature and
▲▼
switch the channels. Press the Point
buttons to select
Off, CC1, CCꢀ, CC3 or CC4.
If the closed caption is not clear, you can change the text
from Color to white.
✔Note:
The Closed Caption is available only under the situation
below.
•
When the input signal is Component (for adjustment
only), Video or S-video, and the system is set to Auto,
NTSC or 480i, the Closed caption is available.
Off
Color
• If the system is set to Auto, and choose NTSC or
480i as the input signal, the Closed caption will be
available.
►
• Closed Caption will be unavailable when under other
setting conditions.
• The Closed caption is unavailable when On-Screen
menu and P-timer are displayed.
• The item of Closed Caption is displayed in gray while it
is not available.
Color
►
Press the Point ▲▼ buttons to select
Off, CC1, CCꢀ, CC3 or CC4, and then
press the SELECT button.
5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Lamp control
Lamp control
This function allows you to change brightness of the
screen.
High........... Brighter than the Normal mode.
Normal....... Normal brightness
Eco ............ Lower brightness reduces the lamp
power consumption and extends the
lamp life.
✔Note:
• Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.
Remote control
This projector provides two different remote control codes:
the factory-set initial code (Code 1) and the secondary code
(Code ꢀ). This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
Remote control
When operating the projector in Code ꢀ, both the projector
and the remote control must be switched to Code ꢀ.
To change the code for the projector:
Select either Code 1 or Code ꢀ in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more. After changing the code,
make sure the remote control operates properly.
✔Note:
• When different codes are set on the projector and on the remote control, any operation cannot be made. In that case,
switch the code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long period of time, the remote control code will be reset.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Key lock
Security (Key lock and PIN code lock)
This function allows you to use the Key lock and PIN code
lock function to set the security for the projector operation.
Key lock
This function locks the top control and remote control
buttons to prevent operation by unauthorized persons.
Select Key lock and then press the SELECT button,
and select the desired item by pressing the Point ▲▼
buttons.
..... Unlocked.
..... Lock the operation of the top control. To
unlock, use the remote control.
..... Lock the operation of the remote control.
To unlock, use the top control.
If the top control accidentally becomes locked and you do
not have the remote control nearby or there is something
wrong with your remote control, contact the dealer where
you purchased the projector or the service center.
PIN code lock
This function prevents the projector from being operated
by unauthorized persons and provides the following
setting options for security.
Off ........... Unlocked.
On1 ......... Enter the PIN code every time turning on
the projector.
Onꢀ ......... Enter the PIN code to operate the projector
once the power cord is disconnected; as
long as the AC power cord is connected,
the projector can be operated without a
PIN code.
PIN code lock
Whenever you change the PIN code lock setting or the
PIN code (the four-digit number), you are required to
enter the PIN code. The “1234” is set as the initial PIN
code at the factory.
If you want to change the PIN code lock setting, press
the SELECT button and the PIN code dialog box
appears.
When the projector is locked with the PIN code, the
Security icon appears on the guide.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Enter a PIN code
Enter a PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ◄ ► buttons to fix the number and move the red
frame pointer to the next box. The number changes to
✳. If you fixed an incorrect number, use the Point ◄ ►
buttons to move the pointer to the number you want to
correct, and then enter the correct number.
Repeat this step to complete entering a four-digit
number.
After entering the four-digit number, move the pointer to
Set. Press the SELECT button so that you can change
the following PIN code lock setting.
If you entered an incorrect PIN code, PIN code and the
number (✳✳✳✳) will turn red for a moment. Enter the
correct PIN code all over again.
Change the PIN code lock setting
Use the Point ▲▼ buttons to select Off, On1 or Onꢀ,
and then press the SELECT button to make a choice.
Change the PIN code
Change the PIN code
The PIN code can be changed to your desired four-digit
number. Press the SELECT button to select PIN code
change. Pin code dialog box appears, use the Point ▲▼
buttons to enter the correct code. The New PIN code
input dialog box appears. Set a new PIN code.
Current PIN code
CAUTION:
wHEN yOU HAVE CHANGED THE PIN CODE, wRITE
DOwN THE NEw PIN CODE IN COLUMN OF THE
PIN CODE NO. MEMO ON PAGE 76, AND KEEP IT
SECURELy. IF yOU FORGET yOUR PIN CODE, THE
PROjECTOR CAN NO LONGER BE STARTED.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Fan
This function provides the following options in the cooling
fans’ operation when the projector is turned off (p.20).
L1 ...... Normal operation
Lꢀ ...... Slower and lower-sound than the normal operation
(L1), but it takes more time to cool the projector
down.
Fan control
Choose the running speed of cooling fans from the following
options according to the ground elevation under which you
use the projector.
Off................ Normal speed. Set this function to Off when
using the projector in non-high altitude
environment.
On1............. Faster than Off mode. Select this mode
when using the projector in high altitudes
(about 1,000 meters to 2,000 meters above
the sea level) where the fans have less
cooling effect.
Onꢀ............. Faster than On1 mode. Select this mode
when using the projector in higher altitudes
(about 2,000 meters to 3,000 meters
above the sea level) where the fans have
lesser cooling effect.
Lamp counter reset
✔Note:
The fan noise becomes louder in On1 and On2.
Video delay control
When you want to make a digital processing of a projected
image faster, set this function.
Use the Point ▲▼ buttonsꢀ select an item o� Off or On.
✔Note:
Noise reduction and Progressive can not be selected
when Video delay control is set to On.
Lamp counter
Be sure to reset the Lamp replacement counter after the
lamp is replaced. (p. 62)
▲▼
Press the Point
buttons to choose the Lamp counter
►
function and then press the Point or the SELECT button to
access the submenu items.
Lamp counter................This item shows the total
accumulated time of the lamp
usage.
Lamp counter reset.......Press the SELECT button to
choose Lamp counter reset.
Select yes in the confirmation
box if you want to reset the lamp
counter, and then choose yes in
the second confirmation box to
reset lamp counter.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Filter counter
Filter counter
This function is used to set a frequency for the filter
cleaning.
When the projector reached a specified time for cleanings,
a Filter warning icon appears on the screen, notifying the
cleaning is necessary. After cleaning the filter, be sure to
select Reset and set the timer. The Filter warning icon will
not turn off until the filter counter is reset.
For details about resetting the timer, refer to “Resetting the
Filter Counter” on page 60.
Fig.1 Filter warning icon
Press the SELECT button to select Timer, and then use
the Point ▲▼ buttons to set the timer. Select from (Off/
100H/ ꢀ00H/ 300H) depending on the use environment.
Filter warning icon appears on the screen at a set time.
✔Note:
This icon also appears at turning on.
✔Note:
The Filter warning icon (Fig.1) will not appear when the
Display function is set to Off (p.45), during Freeze(p.25),
or No show (p.26).
Factory default
warning log
This function records anomalous operations while the
projector is in operation and use it when diagnosing faults.
Up to 10 warning logs are displayed with the latest warning
message at the top of the list, followed by previous warning
messages in chronological order.
✔Note:
When the Factory default function is executed, all the
warning log records will be deleted.
Factory default
This function returns all setting values except for the User
logo, PIN code lock, Logo PIN code lock, Lamp counter
and Filter counter to the factory default settings.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
Input Source Information Display
The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.
Direct Operation
Press the INFO. button on the remote control to display the
Information Menu.
Remote Control
INFO. button
Menu Operation
▲▼
Press the Point
buttons to select the Information. The
Information Menu is displayed.
See below for displayed information.
Input
Information Menu
The selected input source is displayed.
H-sync freq.
The horizontal frequency of the input signal is displayed in
KHz, or - - - - KHz when no signal.
V-sync freq.
The vertical frequency of the input signal is displayed in Hz,
or - - - - Hz when no signal. Numbers of Hz doubles when
during Interlace.
Screen
The selected screen size is displayed.
Language
The selected language is displayed.
Lamp status
The selected lamp mode is displayed.
Lamp counter
The cumulative lamp operating time is displayed.
Power management
Off, Ready or Shut down, and Timer are displayed.
Key lock
The selected Key lock icon is displayed.
PIN code lock
Off or On1 or Onꢀ is displayed.
Remote control
The selected remote code is displayed.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
wARNING indicator
The WARNING indicator shows the state of the function which protects the projector. Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the wARNING
indicator is blinking red.
Top Control
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down to
protect the inside of the projector. The POWER indicator is
blinking while the projector is being cooled down. When the
projector has cooled down enough (to its normal operating
WARNING blinking
red
temperature), it can be turned on again by pressing the ON/
STAND-BY button.
✔Note:
The WARNING indicator continues to blink even after
the temperature inside the projector returns to normal.
When the projector is turned on again, the WARNING
indicator stops blinking.
Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if the air
vents of the projector are not blocked.
– Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the
projector away from the duct or vent.
– Is the filter clean? Clean the filter periodically.
The projector is shut down and the wARNING
indicator lights red.
Top Control
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside of the projector
and the WARNING indicator lights red. In this case, unplug
the AC power cord and reconnect it, and then turn the
projector on once again to verify operation. If the projector
cannot be turned on and the WARNING indicator still lights
red, unplug the AC power cord and contact the service
center.
WARNING lights
red
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE
AC POWER CORD CONNECTED UNDER AN
ABNORMAL CONDITION. IT MAY RESULT IN
FIRE OR ELECTRIC SHOCK.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Cleaning the Filters
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filters become
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup
and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, clean the filters
immediately. Clean the filters by following the steps below.
Turn off the projector, and unplug the AC power cord
from the AC outlet.
1
Remove the panel front assembly by pulling the latch
horizontally.
Remove the panel net by pulling the latch horizontally
and then remove it leftward.
ꢀ
Spacer filter front
Panel
front
Panel front assembly
Clean the filters with a brush or rinse them softly.
Pull horizontally and remove.
3
4
When cleaning the filters by rinsing, dry them well.
Replace the filters properly. Make sure that the filters
are fully inserted.
✔Note:
Please be sure to
fit this edge when
inserting this panel
front assembly.
CAUTION
Do not operate the projector with the filters
removed. Dust may accumulate on the optical
elements degrading picture quality.
Do not put anything into the air vents. Doing so
may result in malfunction of the projector.
RECOMMENDATION
Panel net (filter back)
Pull horizontally and then remove it leftward.
we recommend avoiding dusty/smoky environments
when you operate the projector. Usage in these
environments may cause poor image quality.
When using the projector under dusty or smoky conditions,
dust may accumulate on a lens, LCD panels, or optical
elements inside the projector degrading the quality of a
projected image. When the symptoms above are noticed,
contact your authorized dealer or service center for proper
cleaning.
Filter counter
Resetting the Filter Counter
Be sure to reset the Filter counter after cleaning or replacing
the filters.
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Setting and
then press the Point ► or the SELECT button.
1
Filter counter
Reset? appears.
Use the Point ▲▼ buttons to select Filter counter and
then press the Point ► or the SELECT button. Use the
Point ▲▼buttons to select Filter counter reset and
then press the SELECT button. Filter counter Reset?
appears. Select yes to continue.
ꢀ
Select yes, then
another confirmation
box appears.
Another confirmation dialog box appears, select yes to
reset the Filter counter.
3
Select yes again
to reset the Filter
counter.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Attaching the Lens Cap
When moving this projector or while not using it over an
extended period of time, replace the lens cap.
Attach the lens cap according to the following procedures.
Thread the string through the hole on the lens cap and
then tie a knot in the string to secure it in place.
1
To pass the other end of the string into the hole on the
bottom of the projector and pull at it.
2
Cleaning the Projection Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that
contains a small amount of non-abrasive camera lens
cleaner, or use a lens cleaning paper or commercially
available air blower to clean the lens.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the lens.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth.
When the cabinet is heavily soiled, use a small amount of
mild detergent and finish with a soft dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive cleaners,
solvents, or other harsh chemicals might scratch the surface
of the cabinet.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.
CAUTION
Do not use any flammable solvents or air sprays on the
projector and in its vicinity. The explosion or fire hazard
may occur even after the AC power cord is unplugged
because the temperature inside the projector is extremely
high due to the lamps. In addition, there is a risk that the
internal parts may be damaged not only by the flammable
air spray but also by the cold air.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Lamp Replacement
When the projection lamp of the projector reaches its end
of life, the Lamp replacement icon appears on the screen
and LAMP REPLACE indicator lights yellow. Replace the
lamp with a new one promptly. The timing when the LAMP
REPLACE indicator should light is depending on the lamp
mode.
Top Control
LAMP REPLACE
indicator
Lamp replacement icon
✔Note:
• The Lamp replacement icon will not appear when the Display function is set to Off (p.45), during Freeze
(p.25), or No show (p.26).
CAUTION
Allow a projector to cool for at least 45 minutes
before you open the Lamp Cover. The inside of
the projector can become very hot.
CAUTION
For continued safety, replace with a lamp of the
same type. Do not drop a lamp or touch a glass
bulb! The glass can shatter and may cause injury.
CAUTION
When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be
broken.
If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that
the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the
lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get
into your eyes or mouth, seek medical advice immediately.
Lamp Cover
Follow these steps to replace the lamp.
Unplug the AC power cord. Let the projector cool for at
least 45 minutes.
1
Loosen the screw and open the lamp cover.
ꢀ
Screw
Loosen the three (3) screws that secure the lamp. Lift
3
Screw
the lamp out of the projector by using the handles.
Handles
Screw
Replace the lamp with a new one and secure the three
(3) screws. Make sure that the lamp is set properly.
Close the lamp cover and secure the screw.
4
Lamp
Connect the AC power cord to the projector and turn
on the projector.
5
6
Reset the lamp replacement counter.
See "Lamp Counter" on page 56.
Screw
6ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
● Model No. of your projector
: PLC-XE34
● Replacement Lamp Type No.
: POA-LMP14ꢀ
(Service Parts No. 610 349 7518)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp li�fe maꢁy di�f�fer �from lamp to lamp and according to the en�vironment o�f use. There is no guarantee
of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time
than other similar lamps.
● �I�f the pro�jector indicates that the lamp should be replacedꢀ, i.e.,ꢀ iif� the LA�M�P �REPL�ACE indicator lights
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
● �A Lamp maꢁy e�xplode as a result o�f v�iibrattion,ꢀ sshock or deeggradationn as a rresultt of� hoours of� use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOwING SAFETy PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described on pages 14-16.
–Make sure all equipment is connected to AC outlet and the power is turned on.
–When the projector does not project an image from the connected computer, restart the computer.
Problem:
– Solutions
No power
– Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
– Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator
turns red. See page 18.
– Check the WARNING indicator. If the WARNING indicator lights red,
projector cannot be turned on. See page 59.
– Check the projection lamp. See page 62.
– Unlock the Key lock function for the projector. See page 54.
The initial display is not shown.
– Make sure Off or Countdown off are not chosen at display
function. See page 45.
The initial display is not same
as the default set.
– Make sure User or Off are not chosen at Logo (select)
function. See page 46.
Input signal switches automatically. – Make sure Input search function is adjusted properly. See page 44.
(or does not switch automatically)
when the projector is on and you
press the input source buttons,
an icon other than the Lamp mode
icon appears.
– That is the Filter warning icon. See page 57.
An icon other than Input mode or
Lamp mode icon appears.
– That is the Lamp replacement icon or the Filter warning icon. See
pages 57 or 62.
Image is out of focus.
– Adjust focus of the projector. See page 23.
– Provide proper distance between the projector and the projection
screen. See page 13.
– Check the projection lens to see if it needs cleaning. See page 61.
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. In such cases, leave
the projector off and wait until condensation evaporates.
Image is Left/Right reversed.
Image is Top/Bottom reversed.
– Check the Ceiling/Rear function. See page 49.
– Check the Ceiling function. See page 49.
Picture is not bright enough.
– Check if the Contrast or Brightness is adjusted properly. See
pages 33, 40.
– Check if Image mode is selected properly. See pages 32, 39.
– Check the lamp control function. See pages 25, 53.
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life
is approaching. Replace the lamp with a new one promptly. See page
62.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
No image
– Check the connection between your computer or video equipment
and the projector. See pages 14-16.
– See if the input signal is correctly output from your computer. Some
laptop computers may need to change the setting for monitor output
when connecting to a projector. See your computer’s instruction
manual for the setting.
– It takes about 30 seconds to display an image after turning on the
projector. See page 18.
– Check the Input signal, color system, video system or computer
system mode.
– Make sure the temperature is not out of the specified Operating
Temperature (41˚F–95˚F [5˚C–35˚C]).
– When No Show is operating, the image cannot be displayed. Press
the NO SHOW button or any other button on the remote control.
No sound
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button. See page 24.
– Press the Mute button. See page 24.
– When the AUDIO OUT is plugged-in, the projector's built-in speaker
is not available.
– Is the image projected? You will hear the sound only when the image
is projected.
The color is strange.
– Check the Input signal, color system,video system or computer
system mode.
– Make sure the Blackboard is not selected on Image select
menu. See pages 32, 39.
Some displays are not seen
during the operation.
– Check the Display function. See page 45.
Auto PC adjustment function
does not work.
– Check the Input signal. Auto PC adjustment function can not work
when 480p,575p.7ꢀ0p,480i,575i,1035i or 1080i is selected. See
page 29.
The setting does not remain
after turning off power.
– Make sure you selected Store after adjusting setting. Some settings
can not be stored if not registered with Store. See pages 34, 41.
Power management does not
work.
– Power management function can not work while Freeze or No
Show function is running. See page 50.
Capture function does not work.
– Check the connection and the input signal to see if there is signal.
Auto setup does not work properly. – Make sure Off is not selected at any function of Auto setup. See page
44.
– Make sure On is not selected at the Ceiling function. See page 49.
Auto keystone function does not
work even when the projector is
tipped.
– Make sure the Auto keystone function is not set to Manual. Press
the AUTO SETUP button on the top control. See pages 23, 44.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
The image is distorted or runs off. – Check PC adjust menu or Screen menu and adjust them.
See pages 30-31, 34-35.
PIN code dialog box appears
at start-up.
– PIN code lock is being set. Enter a PIN code (the “1234” or numbers
you have set). See pages 19, 54-55.
The Remote Control does
not work.
– Check the batteries.
– Make sure no obstruction is between the projector and remote
control.
– Make sure you are not too far from the projector when using the
remote control. Maximum operating range is 16.4'(5 m).
– Make sure the code of the remote control is conformed to the
projector’s code. See page 53.
– Unlock the Key lock function for the remote control function. See
page 54.
Indicator blinks or lights.
– Check the status of the projector with referring to "Indicators and
projector Condition". See page 70.
The exclamation mark appears
on the screen.
– Your operation is invalid. Operate correctly.
Top control does not work.
– The top control is not available if the top control is locked at Key lock
under Security of SETTING section. See page 54.
Unable to unlock the Logo PIN
code lock, Security key lock
or Security PIN code lock.
– Contact the dealer where you purchased the projector or the service
center.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
wARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you purchased the
projector or the service center. Specify the model number and explain about the problem. We will advise you
how to obtain service.
This symbol on the nameplate
The CE Mark is a Directive conformity
means the product is Listed
by Underwriters Laboratories
mark of the European Community (EC).
Inc. It is designed and
manufactured to meet rigid
U.L. safety standards against
risk of fire, casualty and
electrical hazards.
Pixelworks ICs used.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Computer Input/Video Input
Input
RGB
Computer 1
Input
Component
RGB (Scart)
S-video
RGB
Computer 2
Video
Sound
Volume
0–31
On/Off
Sound
Mute
Computer Input
Dynamic
Image select
SVGA 1
Standard
System (1)
Mode 1
Mode 2
- - - -
Real
Blackboard (Green)
Colorboard
Image 1
Red/Blue/Yellow/Green
Image 2
Image 3
Image 4
* Systems displayed in the System Menu vary
depending on an input signal.
Auto PC adj.
PC adjust
Fine sync
Total dots
Horizontal
Vertical
0–31
Contrast
0–63
Image Adjust
Brightness
Color temp.
0–63
XLow
Low
Current mode
Mid
Clamp
Display area H
High
Display area V
Reset
User
Yes/No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Red
0–63
Mode free
Green
Blue
0–63
0–63
0–15
Sharpness
Gamma
Reset
0–15
Yes/No
Image 1
Image 2
Image 3
Image 4
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Store
Normal
Screen
True
Wide
Store
Full
Custom
Custom adj.
Scale
H&V
H/V
On/Off
H/V
Mode 6
Mode 7
Mode 8
Mode 9
Mode 10
Position
Yes/No
Yes/No
Common
Reset
Digital zoom +
Digital zoom –
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Video Input
Setting
Auto
1080i
1035i
720p
575p
480p
575i
Setting
Language
20 languages provided.
System (2)
Menu position
Auto setup
Input search
Auto PC adj.
Off/On1/On2
On/Off
Auto keystone
Auto
480i
Manual
Off
Auto
System (3)
PAL
Keystone
Keystone
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
Store/Reset
Store
Background
Display
Blue/User/Black
Off /On/Countdown off
Logo select
Off
Logo
Default
Dynamic
Standard
Cinema
Image select
User
Capture
Yes/No
Blackboard (Green)
Colorboard
Image 1
Logo PIN code lock
Off/On
Logo PIN code change
Red/Blue/Yellow/Green
Image 2
Ceiling
Rear
On/Off
Image 3
On/Off
Image 4
Terminal
Computer 2/Monitor out
Power management
Ready
Shut down
Off
Contrast
Brightness
Color
0–63
0–63
0–63
0–63
Image Adjust
Timer (1–30 Min)
On/Off
Direct on
Tint
Standby mode
P-timer
Eco/Network
Color temp.
XLow
Low
Mid
Count up
Count down
Timer
High
Start
User
0–63
0–63
0–63
0–15
0–15
Off
Reset
Red
Exit
Green
Closed Caption
Lamp control
Closed Caption
Color
Off/CC1/CC2/CC3/CC4
Color/White
Blue
Sharpness
Gamma
Noise reduction
High/Normal/ECO
Lamp control
L1
Remote control
Security
Code 1–Code 2
L2
Key lock
Off
Progressive
Off
L1
Projector
Remote control
PIN code lock
Off/On1/On2
PIN code change
L2
Film
Reset
Store
Yes/No
Image 1
Image 2
Image 3
Image 4
Fan
L1/L2
Fan control
Off/On1/On2
Video delay control
Off/On
Lamp counter
Lamp counter
H
Normal
Screen
Lamp counter reset
Yes/No
Wide
Filter counter
Warning log
Filter counter
Timer
H
Custom
Custom adj.
Off/100H/200H/300H
Scale
Filter counter reset
H/V
Yes/No
H&V
On/Off
H/V
Position
Factory default
Yes/No
Yes/No
Yes/No
Common
Reset
Information
Input Source Information Display
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for projector condition.
Indicators
Projector Condition
LAMP
POWER WARNING
REPLACE
red/green
red
yellow
The projector is off. (The AC power cord is unplugged.)
The projector is in stand-by mode. Press the ON/STAND-BY button
to turn on the projector.
✽
✽
The projector is operating normally.
The projector is preparing for stand-by or the projection lamp is
being cooled down. The projector cannot be turned on until cooling
is completed and the POWER indicator stops blinking.
✽
✽
The projector is in the Power management mode.
The temperature inside the projector is abnormally high. The
projector cannot be turned on. When the projector is cooled down
enough and the temperature returns to normal, the POWER
indicator stops blinking and the projector can be turned on. (The
WARNING indicator keeps blinking.)
✽
✽
The projector has been cooled down enough and the temperature
returns to normal. When turning on the projector, the WARNING
indicator stops blinking.
The projector detects an abnormal condition and cannot be turned
on. Unplug the AC power cord and plug it again to turn on the
projector. If the projector is turned off again, unplug the AC power
cord and contact the dealer or the service center for service and
checkup. Do not leave the projector on. It may cause an electric
shock or a fire hazard.
✽
• • • green.
• • • blinks green.
• • • red
• • • off
• • • blinks red.
When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this
indicator lights yellow, replace the projection lamp with a new one promptly. (pp. 56, 62)
✽
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below
and less than 140 MHz of Dot Clock.
When selecting these modes, PC adjustment can be limited.
ON-SCREEN
DISPLAy
VGA 1
H-Freq.
(KHz)
31.47
V-Freq.
(Hz)
59.88
ON-SCREEN
DISPLAy
SXGA 5
H-Freq.
(KHz)
63.74
V-Freq.
(Hz)
60.01
RESOLUTION
RESOLUTION
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
768 x 575
640 x 480
768 x 576
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1152 x 900
1280 x 1024
1280 x 1024
1280 x 1024
1400 x 1050
1400 x 1050
1400 x 1050
1152 x 870
1280 x 960
1280 x 1024
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1280 x 768
1280 x 768
1280 x 768
1280 x 800
1280 x 800
1280 x 800
1280 x 800
1920 x 1200
1920 x 1200
1680 x 1050
1440 x 900
1440 x 900
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
1280 x 720
1280 x 720
1920 x 1035
1920 x 1080
1920 x 1080
VGA 2
VGA 3
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
31.47
31.25
15.734
15.625
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
59.88
50.00
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15
SXGA 16
SXGA 17
SXGA 18
SXGA 19
SXGA 20
SXGA+ 1
SXGA+ 2
SXGA+ 3
MAC21
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.97
65.35
65.12
68.68
75.00
80.00
48.36
47.70
48.36
56.16
47.776
60.289
68.633
49.600
41.200
49.702
63.98
74.556
74.038
65.290
55.935
74.918
75.00
81.25
87.5
67.19
76.107
60.02
75.025
60.00
65.20
75.60
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480p
86.00
(Interlace)
94.00
(Interlace)
575p
60.01
72.00
66.00
60.00
480i
(Interlace)
50.00
575i
(Interlace)
86.70
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
(Interlace)
60.18
85.024
60.19
60.12
59.90
75.06
75.08
75.08
60.00
60.00
60.00
72.00
59.87
74.893
84.837
60.050
50.000
59.810
60.02
59.885
59.950
59.954
59.887
60.000
60.00
65.00
70.00
75.00
60.00
50.00
MAC
MAC
WXGA 1
WXGA 2
WXGA 3
WXGA 4
WXGA 6
WXGA 7
WXGA 8
WXGA 9
WXGA 10
WXGA 11
WXGA 12
WUXGA 1
WUXGA 2
WSXGA+ 1
WXGA+ 1
WXGA+ 2
UXGA 1
UXGA 2
UXGA 3
UXGA 4
720p
MAC 19
XGA 1
1024 x 768
1024 x 768
60.24
48.36
75.08
60.00
XGA 2
XGA 3
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
58.03
64.20
62.50
63.90
63.34
84.997
75.03
70.07
74.92
60.02
54.58
79.35
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
87.17
XGA 9
(Interlace)
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
XGA 15
SXGA 1
SXGA 2
SXGA 3
SXGA 4
77.07
75.70
86.96
(Interlace)
58.20
58.30
72.00
70.40
58.60
60.00
59.98
93.75
45.00
37.50
33.75
33.75
28.125
720p
1035i
1080i
60.00
(Interlace)
60.00
(Interlace)
50.00
1080i
(Interlace)
✔Note:
The specifications are subject to change without notice.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Mechanical Information
Projector Type
Multi-media Projector
Dimensions (W x H x D)
Net Weight
13.13" x 3.35" x 9.72" (333.5mm x 85.2mm x 247.0mm) (Not including protrusions)
5.7 lbs (2.6 kg)
Foot �d�ustment
0˚ to 10˚
Panel Resolution
LCD Panel System
Panel Resolution
0.55" TFT Active Matrix type, 3 panels
1,024 x 768 dots
Number of Pixels
2,359,296 (1,024 x 768 x 3 panels)
Signal Compatibility
Color System
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15 kHz–100 kHz, V-sync. 50–100 Hz
SD/HD TV Signal
Scanning Frequency
Optical Information
Projection Image Size (Diagonal)
Throw Distance
Adjustable from 40” to 300”
4.3' - 38.7' (1.30m - 11.80m)
Projection Lens
F 2.0 ~ 2.15 lens with f 18.38 mm ~ 22.06 mm with manual zoom and focus
215 W
Projection Lamp
Interface
Video Input Jack
RCA Type x 1
Audio Input Jack
RCA Type x 2
Computer In 1/S-video In/Component In
/Computer In 2/Monitor Out Audio Input Jack
Computer In 1/S-video In
/Component Input Jack
Computer In 2 / Monitor Out Terminal
Control port
Mini Jack (stereo) x 1
Mini D-sub 15 pin x 1
Mini D-sub 15 pin x 1
D-sub 9 pin x 1
Audio Output Jack
Mini Jack (stereo) x 1 (variable)
RJ45
LAN Connection Terminal
Audio
Internal Audio Amp
1.0 W RMS
Built-in Speaker
1 speaker, ø1.1" (28mm)
Power
Voltage and Power Consumption
AC 100–120 V (3.5A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 100–240 V (3.5A-1.9A Max. Ampere), 50/60 Hz (For other countries)
Operating Environment
Operating Temperature
Storage Temperature
41˚F–95˚F (5 ˚C–35 ˚C)
14˚F–140˚F (-10˚C–60 ˚C)
Remote Control
Battery
AAA or LR03 1.5V ALKALINE TYPE x 2
16.4ꢂ (5 m)��30˚
Operating �ange
Dimensions
2.0" (W) x 0.7" (H) x 4.3" (D) (52 mm x 18 mm x 110 mm)
2.37 oz (67 g) (including batteries)
Net Weight
7ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Accessories
Owner’s Manual (CD-ROM)
Quick Reference Guide & Safety Manual
AC Power Cord
Remote Control and Batteries
VGA Cable
Lens Cap with String
PIN Code Label
Ferrite core
● The specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are
effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Model No.
COMPONENT-VGA Cable
S-video-VGA Cable
SCART-VGA Cable
VGA-Cable (10 m)
: POA-CA-COMPVGA
: POA-CA-VGAS
: POA-CA-SCART
: KA-MC-DB10
Soft Carrying Case
: POA-CAC-VCL2
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Pj Link Notice
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information
System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified
conformance with PJLink Standard Class 1.
For PJ Link password, see the owner’s manual of “Network Set-up and Operation.”
Projector Input
Computer 1
PJLink Input
RGB 2
Parameter
RGB
12
13
15
Component
RGB (Scart)
RGB 3
RGB 5
S-video
RGB
RGB 4
14
11
22
Computer 2
Video
RGB 1
Video
VIDEO 2
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Configurations of Terminals
COMPUTER IN 1 / S-VIDEO IN / COMPONENT IN
Terminal: Analog RGB (Mini D-sub 15 pin)
Red/Cr/S-C Input
Green/Y/S-Y Input
Blue/Cb/--- Input
1
9
+5V Power
Ground (Vert.sync.)
Ground
2
1
5
4
3
ꢀ
3
4
5
6
7
8
10
11
10
9
8
7
6
15
12
11
14
13
-----
Ground (Horiz.sync.)
Ground (Red)
1ꢀ DDC Data
Horiz. sync. Input/Output (Composite H/V sync.)
13
14
Vert. sync.
Ground (Green)
Ground (Blue)
15 DDC Clock
COMPUTER IN ꢀ/MONITOR OUT (ANALOG)
Terminal: Analog RGB (Mini D-sub 15 pin)
Red Input/Output
Green Input/Output
Blue Input/Output
1
9
-----
2
1
5
4
3
Ground (Vert.sync.)
ꢀ
3
4
5
6
7
8
10
11
1ꢀ
13
14
15
10
9
8
7
6
15
12
11
14
13
-----
-----
-----
Ground (Horiz.sync.)
Ground (Red)
Horiz. sync. Input/Output
Vert. sync.
-----
Ground (Green)
Ground (Blue)
CONTROL PORT CONNECTOR (D-sub 9 pin)
Serial
1
2
3
4
5
6
7
8
9
-----
R X D
T X D
-----
SG
-----
RTS
CTS
-----
LAN TERMINAL
1
ꢀ
3
4
TX +
5
6
7
8
-----
RX –
-----
TX –
RX +
-----
-----
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service center.
PIN Code Lock No.
Factory default set No: 1 2 3 4*
Logo PIN Code Lock No.
Factory default set No: 4 3 2 1*
*Should the four-digit number be changed,
the factory set number will be invalid.
While the projector is locked with the PIN code.
Put the label below (supplied) on in a prominent place of the
projector's body while it is locked with a PIN code.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Dimensions
Unit: mm(inch)
Screw Holes for Ceiling Mount
Screw: M4
Depth: 10.0(0.39)
333.5
(13.13)
217.0
(8.54)
99.5
(3.92)
10.0
(0.39)
50.0
(1.97)
51.0
(2.01)
77
Download from Www.Somanuals.com. All Manuals Search And Download.
KJ2AC
Download from Www.Somanuals.com. All Manuals Search And Download.
|
