Network Supported
□ Wired LAN
Multimedia Projector
100-Base-TX/10-Base-T
Refer to the owner’s manual
below for details about network
function.
■ Network Set-up and Operation
■ PJ Network Manager
*
MODEL PLC-WXE46
Owner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Trademarks
Each name of corporations or products in this book is either a registered trademark or a trademark of its
respective corporation.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
To the Owner
Safety Precaution
Before installing and operating the projector, read this
manual thoroughly.
WARNING: ● THIS APPARATUS MUST BE EARTHED
The projector provides many convenient features and
functions. Operating the projector properly enables
you to manage those features and maintain it in good
condition for many years to come.
Improper operation may result in not only shortening
the product life, but also malfunctions, fire hazard, or
other accidents.
If your projector seems to operate improperly, read this
manual again, check operations and cable connections
and try the solutions in the “Troubleshooting” section
on pages 56~58 of this manual. If the problem still
persists, contact the dealer where you purchased the
projector or the service center.
● TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
– This projector produces intense light from the
projection lens. Avoid staring directly into the lens,
otherwise eye damage could result. Be especially
careful that children do not stare directly into the
beam.
– Install the projector in a proper position. Otherwise it
may result in fire hazard.
– Allowing the proper amount of space on the top, sides,
and rear of the projector cabinet is critical for proper
air circulation and cooling of the unit. The dimensions
shown here indicate the minimum space required.
If the projector is to be built into a compartment or
similarly enclosed, these minimum distances must be
maintained.
– Do not cover the ventilation slot on the projector. Heat
build-up can reduce the service life of your projector,
and can also be dangerous.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER-SERVICEABLE
PARTS INSIDE EXCEPT LAMP
REPLACEMENT REFER SERVICING
TO QUALIFIED SERVICE
SIDE and TOP
REAR
PERSONNEL
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
– If the projector is unused for an extended time, unplug
the projector from the power outlet.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
OWNER'S MANUAL WITH THIS UNIT.
– Do not project the same image for a long time. The
afterimage may remain on the LCD panels by the
characteristic of panel.
CAUTION
The symbol mark and recycling systems described below
apply to EU countries and do not apply to countries in other
areas of the world.
DO NOT SET THE PROJECTOR IN GREASY, WET,
OR SMOKY CONDITIONS SUCH AS IN A KITCHEN
TO PREVENT A BREAKDOWN OR DISASTER
IF THE PROJECTOR COMES IN CONTACT
WITH OIL OR CHEMICALS, IT MAY BECOME
DETERIORATED
Your product is designed and manufactured with high quality
materials and components which can be recycled and/or
reused.
The symbol mark means that electrical and electronic
equipment, batteries and accumulators, at their end-oflife,
should be disposed of separately from your household waste.
CAUTION
Note:
Not for use in a computer room as defined in the
Standard for the Protection of Electronic Computer/Data
Processing Equipment, ANSI/NFPA 75.
If a chemical symbol is printed beneath the symbol mark,
this chemical symbol means that the battery or accumulator
contains a heavy metal at a certain concentration. This will be
indicated as follows: Hg: mercury, Cd: cadmium, Pb: lead
Ne peut être utilisé dans une salle d’ordinateurs telle
que définie dans la norme ANSI/NFPA 75 Standard
for Protection of Electronic Computer/Data Processing
Equipment.
In the European Union there are separate collection systems
for used electrical and electronic equipment,
batteries and accumulators.
Please, dispose of them correctly at your local
community waste collection/recycling centre.
Please, help us to conserve the environment
we live in!
READ AND KEEP THIS OWNER’S MANUAL FOR
LATER USE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for
later use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for example,
in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer
as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following
the operating instructions. Adjust only those controls that
are covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in performance
this indicates a need for service.
Do not place this projector on an unstable cart, stand, or
table. The projector may fall, causing serious injury to a child
or adult, and serious damage to the projector. Use only with
a cart or stand recommended by the manufacturer, or sold
with the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or injury to persons.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to ensure reliable operation of the
equipment and to protect it from overheating.
Upon completion of any service or repairs to this projector,
ask the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked
by placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
NOTE FOR CUSTOMERS IN THE US
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR
DISPOSED OF ACCORDING TO LOCAL, STATE
OR FEDERAL LAWS.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points
or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Do not install the projector near the ventilation duct of air-
conditioning equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
Air Circulation
Installin� the Projector in Proper
Position
Openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked
or covered.
Install the projector properly. Improper Installation may
reduce the lamp life and cause fire hazard.
Do not roll the projector more than
20 degrees from side to side.
CAUTION
Do not point the projector up to
project an image.
Hot air is exhausted from the exhaust vent. When
using or installing the projector, the following
precautions should be taken.
– Do not put any flammable objects or spray can
near the projector. Hot air is exhausted from the air
vents.
– Keep the exhaust vent at least 3’ (1 m) away from
any objects.
Do not point the projector down to
project an image.
– Do not touch a peripheral part of the exhaust vent,
especially screws and metallic part. This area will
become hot while the projector is being used.
– Do not put anything on the projector. Objects put on
the cabinet will not only get damaged but also may
cause fire hazard by heat.
Cooling fans are provided to cool down the projector.
The fan’s running speed is changed according to the
temperature inside the projector.
Do not put the projector on either
side to project an image.
Do not pitch the projector more
than 20 degrees backward and
forward.
CAUTION
Choose the running speed of cooling fans in the fan
control setting according to the altitude in which the
projector is being used (p.49). Failure to do so may
affect the projector life.
Exhaust Vent
(Hot air exhaust)
Movin� the Projector
When moving the projector, replace the lens cover and
retract the adjustable feet to prevent damage to the lens
and cabinet. When the projector is not in use for an
extended period, put it into a suitable case.
Handle the projector carefully; do not drop, bump,
subject it to strong forces, or put other things on the
cabinet.
CAUTION IN CARRYING OR
TRANSPORTING THE PROJECTOR
Exhaust Vent
(Hot air exhaust)
Air Intake
Vent
– Do not drop or bump the projector, otherwise
damages or malfunctions may result.
– When carrying the projector, use a suitable carrying
case.
– Do not transport the projector by courier or any other
transport service in an unsuitable transport case. This
may cause damage to the projector. For information
about transporting the projector by courier or any
other transport service, consult your dealer.
– Do not put the projector in a case before it is cooled
enough.
Air Intake
Vent
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Model Number
Trade Name
Responsible party
Address
: PLC-WXE46
: Sanyo
: SANYO FISHER COMPANY
: 21605 Plummer Street, Chatsworth, California 91311
: (818)998-7322
Telephone No.
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and
certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit
into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into
the outlet, contact your electrician.
AC Power Cord for the United Kin�dom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
ASA
Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus
. If the
fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same
colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated
in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted.
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET
OUTLET
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow ············ Earth
Blue ································· Neutral
Brown ······························ Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the
safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Front
① Focus Lever
② Projection Lens
③ Lens Cover
(See p 5ꢁ for attachin�)
CAUTION
Do not turn on the projector with putting
the lens cover on. The light beam may
damage lens cover and result in fire
hazard.
Attach the lens cover while the projector
is not in use to avoid scratching the lens
surface.
①
①
②
③
④
⑤
④ Exhaust Vents
Back
CAUTION
⑥
④
⑨
⑩
⑦
Hot air is exhausted from the exhaust
vent. Do not put heat-sensitive objects
near this side.
⑤ Infrared Remote Receiver
⑥ Top controls and Indicators
⑦ Speaker
⑧ Air Intake Vent
⑨ Power Cord Connector
⑩ Terminals and Connectors
⑪ Lamp Cover
⑧
⑫ Air Filters
⑬ Adjustable Feet
Bottom
⑧
⑪
⑫
Kensin�ton Security Slot
This slot is for a Kensington lock used to
deter theft of the projector.
*Kensington is a registered trademark of ACCO
Brands Corporation.
⑬
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Rear Terminal
①
②
③
④
⑤
⑥
⑦
(VARIABLE)
AUDIO OUT
R
COMPUTER IN 2 /
MONITOR OUT
COMPUTER
/
L
VIDEO IN
COMPONENT
(MONO)
S-VIDEO IN
AUDIO IN
⑨
⑧
① COMPUTER IN 1/COMPONENT IN
⑥ AUDIO IN
Connect output signal from a computer, RGB scart
21-pin video output, or component video output to
this terminal (pp.14, 16).
When the cable is of the longer variety, it is
advisable to use this terminal and not COMPUTER
IN 2/MONITOR OUT.
Connect the audio output from video equipment
connected to ⑤ or ⑨ to this jack. [When the audio
output is monaural, connect it to L (MONO) jack
(p.15).
⑦ AUDIO OUT (VARIABLE)
Connect an external audio amplifier to this jack
(pp.14 - 16).
This terminal outputs sound from AUDIO IN
② SERVICE PORT
When controlling the projector from a computer,
connect the computer to this connector with a
control cable.
terminal (⑥ or ⑧).
⑧ COMPUTER/COMPONENT AUDIO IN
③ LAN Connection Terminal
Connect the audio output (stereo) from a computer
or video equipment connected to ① or ④ to this
jack (pp.14, 16).
Connect the LAN cable (Refer to the owner's
manual of "Network Set-up and Operation".).
④ COMPUTER IN ꢀ/MONITOR OUT
This terminal is switchable and can be used
for input from a computer or output to the other
monitor.
⑨ VIDEO IN
Connect the composite video output from video
equipment to VIDEO jack (p.15).
Set the terminal up as either Computer input or
Monitor output properly. [Used for Monitor out,
this terminal outputs only incoming signal from
COMPUTER IN 1/COMPONENT IN terminal (pp.
14, 44)].
⑤ S-VIDEO IN
Connect the S-VIDEO output from video equipment
to this jack (p.15).
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Top Control
①
②
③ ④ ⑤ ⑥
⑦
⑧
⑨
① SELECT button
⑥ WARNING indicator
–Execute the selected item (p.20).
–Lights red light when the projector detects an
–Expand or compress the image in Digital zoom
mode (p.33).
abnormal condition.
–Blinks red when the internal temperature of the
projector exceeds the operating range(pp.51, 61).
② ON–OFF button
Turn the projector on or off (pp.18-19).
⑦ LAMP REPLACE indicator
Turn yellow when the life of the projection lamp
③ MENU button
draws to an end (pp.54, 61).
Open or close the On-Screen Menu (p.20).
⑧ KEYSTONE button
④ POWER indicator
Correct the keystone distortion (pp.22, 41).
–Lights red when the projector is in stand-by mode.
–Lights green during operations.
⑨ POINT (▲▼◄►) buttons
–Select an item or adjust the value in the On-
Screen Menu (p.20).
–Blinks green in the Power management mode
(pp.45, 61).
–Pan the image in Digital zoom + mode (p.33).
–Adjust the volume level (Point ◄► buttons)
(p.23).
⑤ INPUT button
Select input source (pp.25, 34, 35).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control
① POWER ON/STAND-BY button
Turn the projector on or off (pp.18, 19).
③
②
①
② VIDEO button
Select VIDEO input port (pp.23, 34).
③ COMPUTER button
Select COMPUTER input port (pp.23, 25, 35).
④ MENU button
Open or close the On-Screen Menu (p.20).
⑤ Point ▲▼◄► (VOLUME + / –) buttons
– Select an item or adjust the value in the On-Screen Menu.
(p.20)
– Pan the image in Digital zoom + mode (p.33).
– Adjust the volume level (Point ◄► buttons) (p.23).
④
⑤
⑮
⑥ SELECT button
– Execute the selected item (p.20).
– Expand or compress the image in Digital zoom mode.
(p.33)
⑭
⑬
⑥
⑦
⑦ D ZOOM ▲▼ buttons
Zoom in and out the images (pp.24, 33).
⑫
⑪
⑧ FREEZE button
Freeze the picture (p.23).
⑨ NO SHOW button
Temporarily turn off the image on the screen (p.24).
⑩ LAMP CONTROL button
Select the lamp mode (pp.24, 46).
⑪ MUTE button
Mute the sound (p.23).
⑫ P-TIMER button
Operate the P-timer function (p.24).
⑧ ⑨
⑩
⑬ IMAGE button
Select the image level (pp.24, 30, 37).
⑭ AUTO PC button
Automatically adjust the computer image to its optimum
setting (pp.24, 27).
⑮ KEYSTONE button
Correct the keystone distortion (pp.22, 41).
To ensure safe operation, observe the following precautions:
– Do not bend, drop, or expose the remote control to moisture
or heat.
– For cleaning, use a soft dry cloth. Do not apply benzene,
thinner, spray, or any other chemicals.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Names and Functions
Remote Control Battery Installation
Open the battery
compartment lid.
Install new batteries into
the compartment.
Replace the
compartment lid.
1
2
3
Two AA size batteries
For correct polarity (+ and
–), be sure battery terminals
are in contact with pins in
the compartment.
To ensure safe operation, please observe the following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid matter.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
● Risk of explosion if a battery is replaced by an incorrect type.
● Dispose of used batteries according to the instructions.
Operatin� Ran�e
Point the remote control toward the projector
(Infrared Remote Receiver) when pressing
any button. Maximum operating range for the
remote control is about 16.4’ (5 m) and 60
degrees in front of the projector.
30°
30°
16.4’
(5 m)
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Positionin� the Projector
For the projector positioning, see the figures below.
The projector should be set perpendicularly to the plane of the screen.
Note:
•This projector is not equipped with an optical zoom. To adjust the screen size, change the throw distance.
•The brightness in the room has a great influence on picture quality. It is recommended to limit the ambient
lighting in order to get the best image.
•All measurements are approximate and may vary from the actual sizes.
3.927’ (119.7 cm)
(Inch Diagonal)
2.826’ (86.1 cm)
110”
1.726’ (52.6 cm)
80”
50”
A
Screen Size
(W x H) mm
16:10aspect ratio
50”
80”
110”
1077 x 673
1723 x 1077
2369 x 1481
Throw distance 1.726’ (52.6 cm) 2.826’ (86.1 cm) 3.927’(119.7 cm)
A
0.623’ (19.0 cm) 0.846’ (25.8 cm) 1.069’ (32.6 cm)
Adjustable Feet
Projection angle can be adjusted up to 10.0 degrees with
the adjustable feet.
Lift the front of the projector and pull the feet lock latches
on both sides of the projector upward.
1
Release the feet lock latches to lock the adjustable feet
and rotate the adjustable feet to adjust the position and
tilt.
2
To retract the adjustable feet, lift the front of the projector
and pull and undo the feet lock latches.
Keystone distortion of the projected image can be
corrected by remote control operation or menu operation
(pp.22, 41).
3
Feet Lock Latches
Adjustable Feet
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connectin� to a Computer
Cables used for connection
• VGA Cables (Mini D-sub 15 pin)*
• Audio Cables (Mini Plug: stereo)
(*One cable is supplied; other cables are not supplied with the projector.)
Monitor Output
Audio Output Monitor Output
or
External Audio Equipment
Monitor Input
Audio Input
VGA cable
VGA cable
Audio cable
(stereo)
Audio cable
(stereo)
COMPUTER IN 1/
COMPONENT IN
COMPUTER IN 2/
MONITOR OUT
This terminal is switchable. Set up the
terminal as either Computer input or
Monitor output (see page 44).
(VARIABLE)
AUDIO OUT
R
R
COMPUTERIN2/
MONITOR OUT
AUDIO OUT
(stereo)
SERVICE PORT
COMPUTER
/
L
L
V
V
I
I
D
D
E
E
O
O
ININ
COMPONENT
((MMOONN
O
O))
SS--VVIIDDEEOOIINN
A
A
U
U
D
D
I
I
O
O
ININ
COMPUTER/
COMPONENT
AUDIO IN
Note:
•Input sound to the COMPUTER/COMPONENT AUDIO IN
terminal when using the COMPUTER IN 1/COMPONENT
IN and the COMPUTER IN 2/MONITOR OUT terminal as
input.
•When the AUDIO OUT is plugged-in, the projector’s
built-in speaker is not available.
•When the cable is of the longer variety, it is advisable to
use the COMPUTER IN 1/COMPONENT IN and not the
COMPUTER IN 2 /MONITOR OUT.
Unplug the power cords of
both the projector and external
equipment from the AC outlet
before connecting the cables.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connectin� to Video Equipment
Cables used for connection
• Video and Audio Cable (RCA x 3)
• S-VIDEO Cable
• Audio Cable (Mini Plug: stereo)
(Cables are not supplied with the projector.)
S-Video Output
Composite Video and Audio Output
(R) (L) (Video)
External Audio Equipment
S-Video cable
Video and Audio cable
Audio Input
S-VIDEO
(R) (L)
AUDIO IN
(Video)
VIDEO
Audio cable
(stereo)
(VARIABLE)
AUDIO OUT
R
COMPUTER IN 2 /
MONITOR OUT
AUDIO OUT
(stereo)
COMPUTER
/
L
VIDEO IN
COMPONENT
(MONO)
S-VIDEO IN
AUDIO IN
Note:
•When the AUDIO OUT is plugged-in, the projector’s
built-in speaker is not available.
•The S-VIDEO jack connection overrides the VIDEO jack
connection when “Auto” is selected in the Input Menu
(p.34).
Unplug the power cords of both the projector
and external equipment from the AC outlet
before connecting the cables.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connectin� to Component Video Equipment
Cables used for connection
• Audio Cables (Mini Plug: stereo)
• Scart-VGA Cable
• Component Cable
• Component-VGA Cable
(Cables are not supplied with the projector.)
Audio Output
RGB Scart 21- Component Video Output
pin Output (Y, Pb/Cb, Pr/Cr)
Component
cable
External Audio Equipment
Audio cable
(stereo)
Scart-VGA
cable
Component-VGA
cable
Audio Input
COMPUTER IN 1/COMPONENT IN
Audio cable
(stereo)
(VARIABLE)
AUDIO OUT
R
COMPUTER IN 2 /
MONITOR OUT
AUDIO OUT
(stereo)
COMPUTER
/
L
VIDEO IN
COMPONENT
(MONO)
S-VIDEO IN
AUDIO IN
COMPUTER/
COMPONENT
AUDIO IN
Note:
When the AUDIO OUT is plugged-in, the projector’s
built-in speaker is not available.
Unplug the power cords of both the projector
and external equipment from the AC outlet
before connecting the cables.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connectin� the AC Power Cord
This projector uses nominal input voltages of 100–120 V
or 200–240 V AC and it automatically selects the correct
input voltage. It is designed to work with single-phase power
systems having a grounded neutral conductor. To reduce
the risk of electrical shock, do not plug into any other type of
power system.
If you are not sure of the type of power being supplied,
consult your authorized dealer or service station.
Connect the projector with all peripheral equipment before
turning it on.
CAUTION
Connect the AC power cord (supplied) to the
projector.
The AC outlet must be near this equipment and must be easily
accessible.
Note:
Unplug the AC power cord when the projector is not in
use. When the projector is connected to an outlet with the
AC power cord, it is in stand-by mode and consumes a
little electric power.
NOTE ON THE POWER CORD
AC power cord must meet the requirements of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If the supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For the U S A and Canada
For Continental Europe
For the U K
Ground
To power cord
connector on your
projector.
To the AC outlet.
(1ꢀ0 V AC)
To the AC outlet.
(ꢀ00–ꢀ40 V AC)
To the AC outlet.
(ꢀ00–ꢀ40 V AC)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turnin� On the Projector
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
1
2
16
Connect the projector’s AC power cord into an AC
outlet. The POWER indicator turns red. Open the lens
cover.
Press the POWER ON/STAND-BY button on the
remote control. The POWER indicator becomes green
and the cooling fans start to operate. The preparation
display appears on the screen and the count down
starts.
3
The preparation display disappears after 30 seconds.
Selected Input Source and Lamp Control
Video
After the countdown, the input source that was
selected the last time and the Lamp control status icon
(see page 46) will appear on the screen.
If the projector is locked with a PIN code, a PIN code
Input Dialog Box appears. Enter the PIN code as
instructed below.
4
Lamp control status
See page 46 for the Lamp control.
Note:
The Filter warning and Lamp replacement
icons may appear on the screen depending on
the usage state of the projector.
Enter a PIN code
Select a number by pressing the Point ▲▼ buttons, and
then press the Point ► button to fix the number and move
the pointer. The number changes to "". If you fixed an
incorrect number, move the pointer to the number you want
to correct by pressing the Point ► button, and then select
the correct number by pressing the Point ▲▼buttons.
PIN Code Input Dialo� Box
PIN code
Repeat this step to complete entering a four-digit number.
"1234" is set as the initial PIN code at the factory.
PIN code
After entering the four-digit number, move the pointer to
"Set" by pressing the Point ► button. Press the SELECT
button so that you can start to operate the projector.
If you entered an incorrect PIN code, "PIN code" and the
number () turns red. Enter the correct PIN code all
over again.
OK
After the OK icon
disappears, you can
operate the projector.
What is PIN code?
Note:
PIN (Personal Identification Number) code is a security code
that allows the person who knows it to operate the projector.
Setting the PIN code prevents unauthorized use of the
projector.
•When the Input Search function is set on
On1 or On2, the input signal will be searched
automatically (p.44).
•When the Logo select function is "Off,” the
logo will not be displayed on the screen
(p.42).
•When the "Countdown off" or "Off" is selected
in the Display function, the countdown will not
be shown on the screen (p.41).
•During the countdown period, all operations
are invalid.
•If the PIN code number is not entered within
three minutes after the PIN code dialog box
appeared, the projector will be turned off
automatically.
A PIN code consists of a four-digit number. Refer to the PIN
code lock function in the Setting Menu on pages 47–48 for
locking operation of the projector with your PIN code.
CAUTION ON HANDLING THE PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take a special care in setting a
new PIN code; write down the number in a column
on page 67 of this manual and keep it on hand.
Should the PIN code be missing or forgotten, consult
your dealer or service center.
•The “1234” is set as the initial PIN code at the
factory.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Turnin� Off the Projector
Press the POWER ON/STAND-BY button on the
remote control, and “Power off?” appears on the
screen.
1
Power off?
Press the POWER ON/STAND-BY button again to turn
2
off the projector. The POWER indicator starts to blink
red, and the cooling fans keep running. (You can select
the level of the fans’ quietness and running speed. See
page 49.) At this time you can unplug the AC power
cord even if the fans are still running.
“Power off” disappears after 4 seconds.
When the projector has cooled down enough to be
turned on again, the POWER indicator stops blinking.
3
TO MAINTAIN THE LAMP LIFE, ONCE YOU
TURN THE PROJECTOR ON, WAIT AT LEAST 5
MINUTES BEFORE TURNING IT OFF.
DO NOT OPERATE THE PROJECTOR
CONTINUOUSLY WITHOUT REST. CONTINUOUS
USE MAY RESULT IN SHORTENING THE LAMP
LIFE. TURN OFF THE PROJECTOR AND LET
STAND FOR ABOUT AN HOUR IN EVERY 24
HOURS.
Note:
•When the On start function is “On,” this projector is turned
on automatically by connecting the AC power cord to an
AC outlet (p. 46).
•The running speed of cooling fans is changed according
to the temperature inside the projector.
•Do not put the projector in a case before the projector is
cooled enough.
•If the WARNING indicator blinks or emits a red light, see
“Warning Indicator” on page 51.
•While the POWER indicator is blinking, the lamp is being
cooled down and the projector cannot be turned on. Wait
until the POWER indicator stops blinking to turn on the
projector again.
•The fan rotation will terminate directly if the AC power
cord is unplugged immediately after the projector is turned
off.
•The projector can be turned on after the POWER indicator
turns red. The waiting time to restart will be shortened
when the normal power-off processing for fan cooling is
completed, compared with the time the AC power cord is
immediately unplugged after the power-off.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. For each adjustment and setting procedure, refer to
the respective sections in this manual.
Top Control
Press the MENU button on the top control or on the
remote control to display the On-Screen Menu.
MENU button
1
POINT buttons
Use the Point ◄► buttons to select a Menu icon; use
the Point ▲▼ buttons to select an item.
2
Press the SELECT button to show the item data. To
adjust the data, use the Point ◄► buttons. Refer
to the relevant pages for more details about each
adjustment.
3
SELECT button
Remote Control
MENU button
POINT buttons
To close the On-Screen Menu, press the MENU button
again.
Note:
The selected item is not active until the SELECT button is
pressed.
SELECT button
On-Screen Menu
Menu icon
Pointer
(red frame)
Menu bar
Pointer (red frame)
Press the Point ▲▼
buttons to move the
pointer.
Item
SELECT
button
Press the SELECT button
here to display previous
items.
Item data
Press the Point ◄►
buttons to adjust the
value.
Press the SELECT button
here to display next items.
Quit
Exit this menu.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Menu Bar
For detailed functions, see Menu Tree on pages 59-60.
For computer source
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
① Guide Window
⑦ Screen Menu
Shows the selected Menu of the On-Screen Menu.
Used to adjust the size of image from Normal,
True, Full, Custom, and Digital zoom +/– (pp.32–
33).
② Input Menu
Used to select the input source, Computer or Video (p.25).
⑧ Sound Menu
③ PC System Menu
Used to adjust the volume or mute the sound
(p.23).
Used to select the computer system (p.26).
④ PC Adjust Menu
⑨ Settin� Menu
Used to set the projector’s operating configurations
(pp.41–50).
Used to adjust parameters to match with input signal
format (pp.27–29).
⑤ Ima�e Select Menu
Used to select an image level from Dynamic, Standard, Real,
Blackboard (Green), Colorboard and Image 1–4 (p.30).
⑩ Wired settin� Menu
See owner’s manual “Network Set-up and
Operation”.
⑥ Ima�e Adjust Menu
Used to adjust the computer image from Contrast,
Brightness, Color temp., White balance (R/G/B),
Sharpness, and Gamma (pp.31–32).
Note:
Items will be same as the items in video source
when 480i, 575i, 480p, 575p, 720p, 1035i or
1080i is selected.
For video source
⑨
①
②
③
④
⑤
⑥
⑦
⑧
① Guide Window
⑥ Screen Menu
Shows the selected Menu of the On-Screen Menu.
Used to set the size of image to Normal, Full,
Zoom, Wide, Natural wide, or Custom (p.40).
② Input Menu
⑦ Sound Menu
Used to select input source, Video or Computer
(pp.34–35).
Used to adjust the volume or mute the sound
(p.23).
③ AV System Menu
⑧ Settin� Menu
Used to set the projector’s operating configurations
(pp.41–50).
Used to select the system of selected video source (p.36).
④ Ima�e Select Menu
Used to select an image level from Dynamic, Standard,
Cinema, Blackboard (Green), Colorboard and Image 1–4
(p.37).
⑨ Wired settin� Menu
See owner’s manual “Network Set-up and
Operation”.
⑤ Ima�e Adjust Menu
Used to adjust the picture image from Contrast,
Brightness, Color, Tint, Color temp., White balance
(R/G/B), Sharpness, Gamma, Noise reduction, and
Progressive (pp.38–39).
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Focus Adjustment
Adjust the lens focus with the focus lever.
Focus Lever
Keystone Correction
If a projected picture has keystone distortion, correct the
image with the Keystone function.
Press the KEYSTONE button on the top control or on the
remote control. The keystone dialog box appears. Correct
keystone distortion with the Point ▲▼ buttons. Keystone
adjustment can be stored (p.41).
•The arrows are white when there is no correction.
•The direction of the arrow which are being corrected
turns red.
•The arrows disappear at the maximum correction.
•If you press the KEYSTONE button on the remote
control once more while the keystone dialog box is
being displayed, the keystone adjustment is canceled.
•The adjustable range can be limited depending on the
input signal.
Reduce the upper width
with the Point ▲ button.
Reduce the lower width
with the Point ▼ button.
•The projected picture may fluctuate momently
depending on the keystone adjustment.
•“Keystone” disappears after 4 seconds.
Top Control
KEYSTONE button
POINT▲▼ buttons
Remote Control
KEYSTONE button
POINT▲▼ buttons
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Sound Adjustment
Direct Operation
Volume
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Top Control
VOLUME+/- button
Remote Control
Mute
VOLUME- button
VOLUME+ button
Press the MUTE button on the remote control to turn off the
sound. To restore the sound to its previous level, press the
MUTE button again or press the VOLUME+/– buttons. Mute
function is also effective for AUDIO OUT jack.
Menu Operation
MUTE button
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Sound Menu icon.
1
Approximate level
of the volume.
Volume
Mute
Press the Point ▲▼ buttons to move the red frame
pointer to the desired item, and then press the
2
SELECT button.
Press the MUTE button to set the Mute function
On or Off. The display disappears after 4 seconds.
Volume
Press the Point ► button to turn up the volume; press the
Point ◄ button to turn down the volume.
Sound Menu
Mute
Sound Menu
icon
Press the Point ◄► buttons to switch the mute function
On/Off. When the sound is turned off, “On” is displayed.
Press the Point ◄► buttons again to turn the sound back
on.
Approximate level of
the volume.
Exit the Sound Menu.
Remote Control Operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the On-Screen Menu.
Remote Control
COMPUTER/VIDEO button
COMPUTER/VIDEO button
Press the COMPUTER or VIDEO button to select an input
source. See pages 25, 34–35 for more details.
FREEZE button
FREEZE button
Press the FREEZE button to freeze the picture on the
screen. To cancel the Freeze function, press the FREEZE
button again or press any other button.
Note:
See the next page for the description of
other buttons.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Remote Control
AUTO PC button
KEYSTONE button
(See page 22.)
Press the AUTO PC button to operate the Auto PC function.
See page 27 for more details.
VOLUME +/-
buttons
(See page 23.)
POINT ▲▼
buttons
D ZOOM buttons
AUTO PC
button
Press the D.ZOOM buttons to zoom in and zoom out the
images. See page 33 for more details.
IMAGE button
D ZOOM
P-TIMER button
buttons
NO SHOW
button
NO SHOW button
LAMP CONTROL
button
Press the NO SHOW button to black out the image. To
restore to normal, press the NO SHOW button again or
press any other button. When the projected image is
captured and is set as “User” in the Logo selection (p.42),
the screen changes each time you press the NO SHOW
button as follows.
Note:
See the previous page for the description
of other buttons.
• • • • •
black out → the captured image → normal →
No show
KEYSTONE button
For details, see page 22.
IMAGE button
“No show” disappears after 4 seconds.
Press the IMAGE button to select an image level of the
screen. See pages 30, 37 for more details.
P-TIMER button
Press the P-TIMER button. The timer display “00:00”
appears on the screen and the timer starts to count time
(00:00–59:59).
To stop the P-Timer, press the P-TIMER button. Press the
P-TIMER button again, then the P-timer display disappears.
P-Timer display
LAMP CONTROL button
Press the LAMP CONTROL button to select the lamp mode
to change the brightness of the screen.
Normal … Normal brightness
Eco …… Lower brightness reduces the lamp power
consumption and extends the lamp life.
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Input Source Selection
Direct Operation
Top Control
INPUT button
INPUT button
Select either Computer 1 or Computer 2 by pressing the
INPUT button on the top control or the COMPUTER button
on the remote control.
Before using INPUT or COMPUTER button, select the
correct input source through Menu operation as described
below.
Computer 1
Computer ꢀ
Video
*
Remote Control
COMPUTER button
COMPUTER button
Computer 1
Computer ꢀ
*
*See Notes at the bottom of this page.
Input Menu icon
Menu Operation
Input Menu
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Input Menu icon.
1
Move the pointer (red arrow)
to Computer 1 and press the
SELECT button.
Use the Point ▲▼ buttons to move the red arrow
2
pointer to either Computer 1 or Computer 2, and then
press the SELECT button.
Computer
1
After the Source Select Menu appeared for Computer
1, move the pointer to RGB and then press the
SELECT button.
3
Source Select Menu
Move the pointer to RGB
and press the SELECT
button.
Note:
Input Menu
•Computer 2 is not displayed when the COMPUTER IN 2/
MONITOR OUT terminal is set as Monitor out (p.44).
•Computer 2 (COMPUTER IN 2/MONITOR OUT) can
accept only the RGB signal.
Move the pointer (red arrow)
to Computer 2 and press the
SELECT button.
• When the Input Search function is set On1 or On2, the
input signal will be searched automatically (p.44)
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Computer System Selection
The projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA,
or UXGA with its Multi-scan system and Auto PC Adjustment. If computer is selected as a signal source, the
projector automatically detects the signal format and tunes to project proper images without any additional
setting. (Signal formats provided in this projector is shown on page 62.)
One of the following messages may appear when:
The projector cannot recognize the connected
signal conforming to the provided PC Systems.
“Auto” is displayed on the PC System Menu
icon and the Auto PC Adjustment function works
to display proper images. If images are not
projected properly, adjust manually. (pp.28–29)
PC System Menu
Auto
The Auto PC Adjustment
function operates to adjust
the projector.
There is no signal input from computer. Check
the connection between your computer and the
projector. (See “Troubleshooting” on page 56.)
-----
The preset system is manually adjusted in the
PC Adjust Menu. The adjusted data can be
stored in Mode 1–5 (pp.28–29).
Mode 1
SVGA 1
A PC System provided in the projector is
selected. The projector selects a proper system
provided in the projector and displays it.
*Mode 1 and SVGA 1 are examples.
PC System Menu
Selectin� Computer System Manually
PC system can also be selected manually.
The PC System Menu icon
The selected system is
displayed.
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the PC System Menu icon.
1
Available system selection.
Use the Point ▲▼ buttons to move the red arrow
2
pointer to the desired system, and then press the
SELECT button.
Custom Mode (1–5) set in the
PC Adjust Menu (pp.28-29).
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical
positions to conform to your computer.
Direct Operation
Remote Control
The Auto PC adjustment function can be operated directly
with the AUTO PC button on the remote control.
AUTO PC button
Menu Operation
PC Adjust Menu
Auto PC adj
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to PC Adjust Menu.
1
PC Adjust Menu icon
Use the Point ▲▼ buttons to move the red frame
pointer to Auto PC adj. and then press the SELECT
button twice.
2
Move the red frame pointer to the
Auto PC adj. item and press the
SELECT button.
“Please wait...” appears while Auto
PC adjustment is in process.
To store the adjusted parameters
The system parameters adjusted in the Auto PC Adjustment
can be stored in the projector. Once parameters are stored,
the setting can be done just by selecting a Mode in the PC
System Menu (p.26). See “Store” on page 29, for details.
Note:
•Fine sync, Total dots, Horizontal, and Vertical positions of
some computers cannot be fully adjusted with this Auto
PC Adjustment function. When the image is not provided
properly with this operation, manual adjustments are
required (pp.28–29).
•The Auto PC Adjustment cannot be operated when 480i,
575i, 480p, 575p, 720p,1035i, or 1080i is selected in the
PC System Menu (p.26).
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.
Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The
projector has five independent memory areas (Mode 1–5) to store those parameters manually adjusted, which
allows you to recall the setting for a specific computer.
PC Adjust Menu icon
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the PC Adjust Menu icon.
PC Adjust Menu
1
2
Use the Point ▲▼ buttons to move the red frame
pointer to the desired item and then press the SELECT
button to display the adjustment dialog box. Press the
Point ◄► buttons to adjust the value.
Move the red frame pointer
to the desired item and
press the SELECT button.
Fine sync
Use the Point ◄► buttons to adjust the value to cut off
flicker from the image displayed (from 0 to 31).
Status (Stored/Free) of the
selected Mode.
Selected Mode
Total dots
Use the Point ◄► buttons to adjust the number of total dots
in one horizontal period to match your PC image.
Horizontal
Use the Point ◄► buttons
to adjust the value.
Use the Point ◄► buttons to adjust the horizontal picture
position.
Vertical
Use the Point ◄► buttons to adjust the vertical picture
position.
Press the SELECT button
here to move on to other
items.
Current mode
Press the SELECT button to show H-sync freq. and V-sync
freq. of the connected computer.
Clamp
Use the Point ◄► buttons to adjust the clamp level. When
the image has dark bars, try this adjustment.
Press the SELECT button
at “Current mode” to
show the information of
the connected computer.
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Display area H
Use the Point ◄► buttons to adjust the horizontal area
displayed by this projector.
Display area V
Use the Point ◄► buttons to adjust the vertical area
displayed by this projector.
Reset
To reset the adjusted data, select “Reset” and press the
SELECT button. A confirmation box appears and then select
“Yes.” All adjustments return to their previous figures.
Move the red frame pointer
to an item and press the
SELECT button.
Mode free
To clear the stored data, select “Mode free” and then press
the SELECT button. Move the red arrow pointer to the Mode
that you want to clear and then press the SELECT button.
This Mode has
stored parameters.
To clear adjusted data
Store
To store the adjusted data, select “Store” and then press the
SELECT button. Move the red arrow pointer to one of the
Mode 1 to 5 in which you want to store, and then press the
SELECT button.
Vacant Mode
Quit
Values of “Total dots,”
“Horizontal,” “Vertical,”
“Display area H,” and
“Display area V.”
Exit the PC Adjust Menu.
To store adjusted data
Note:
Display area (H/V) cannot be selected when 480i, 575i,
480p, 575p, 720p, 1035i, or 1080i is selected in the PC
System Menu (p.26).
Close this dialog box.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Ima�e Level Selection
Direct Operation
Remote Control
IMAGE button
Dynamic
Select an image level from among Dynamic, Standard,
Real, Blackboard (Green), Colorboard, Image 1, Image 2,
Image 3, and Image 4 with the IMAGE button on the remote
control.
Standard
Real
Dynamic
For viewing pictures in a bright room.
IMAGE
button
Standard
Normal picture level preset on the projector.
Blackboard(Green)
Colorboard
Ima�e 1
Real
Picture level with improved halftone for graphics.
Blackboard (Green)
For viewing the image projected on a blackboard. This mode
assists to enhance the image projected on a blackboard.
This is mainly effective on a green colored board, not truly
effective on a black colored board.
Ima�e ꢀ
Ima�e ꢁ
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Ima�e 4
Ima�e 1–4
User preset image in the Image Adjust Menu (pp.31-32).
Image Select Menu icon
Menu Operation
Ima�e Select Menu
Press the MENU button to display the On-Screen
1
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Image Select Menu icon.
Use the Point ▲▼ buttons to move the red frame
pointer to the desired level and then press the SELECT
button.
2
Move the red frame pointer to
the desired level and press the
SELECT button.
Dynamic
For viewing pictures in a bright room.
Standard
Normal picture level preset on this projector.
Real
Picture level with improved halftone for graphics.
The image level being selected.
Blackboard(Green)
For viewing the image projected on a blackboard. See
above for further description.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors. Press the SELECT button
to choose the color.
Ima�e 1–4
User preset image in the Image Adjust Menu (pp.31-32).
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Ima�e Level Adjustment
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Image Adjust Menu icon.
Ima�e Adjust Menu
1
Image Adjust Menu icon
Move the red frame pointer
to the desired item and then
press the SELECT button.
Use the Point ▲▼ buttons to move the red frame
pointer to the desired item, and then press the
SELECT button. The level of each item is displayed.
Use the Point ◄►buttons to adjust each level.
2
Contrast
Press the Point ◄ button to decrease the contrast; press
the Point ► button to increase the contrast (from 0 to 63).
Bri�htness
Press the Point ◄ button to decrease the brightness; press
the Point ► button to increase the brightness (from 0 to 63).
Selected Image level
Color temp
Use the Point ◄► buttons to select the desired Color temp.
level (XLow, Low, Mid, or High).
Use the Point ◄► buttons to
adjust the value.
White balance (Red)
Press the Point ◄ button to lighten the red tone; press the
Point ► button to deepen the red tone (from 0 to 63).
White balance (Green)
Press the Point ◄ button to lighten the green tone; press
the Point ► button to deepen the green tone (from 0 to 63).
White balance (Blue)
Press the Point ◄ button to lighten the blue tone; press the
Point ► button to deepen the blue tone (from 0 to 63).
Note:
After adjusting the White balance Red,
Green, or Blue, the Color temp. level will
change to “Adj.”.
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to get
better balance of contrast (from 0 to 15).
Reset
To reset the adjusted data, select “Reset” and press the
SELECT button. A confirmation box appears and then select
“Yes.” All adjustments return to their previous figures.
ꢁ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Store
Move the red frame
pointer to the desired
image level (from Image
1 to 4) and then press
the SELECT button.
To store the adjusted data, select “Store” and press the
SELECT button. The Image Level Menu appears. Use the
Point ▲▼ buttons to choose one of the four image level and
press the SELECT button. A confirmation box appears and
then select “Yes.”
The stored data can be called up by selecting “Image” in the
Image Level Selection on page 30.
Quit
A confirmation
box appears,
then select “Yes.”
Exit the Image Adjust Menu.
Store item
Press the SELECT button
at this item to store the
adjusted data.
Screen Size Adjustment
This projector has the picture screen resize function, which enables you to customize the image size.
Screen Menu
Press the MENU button to display the On-Screen
1
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Screen Menu icon.
Screen Menu icon
Use the Point ▲▼ buttons and move the red frame
pointer to the desired function and then press the
2
Move the red frame pointer
to the function and press
SELECT button.
the SELECT button.
Normal
Provide the image to fit the screen size while maintaining
the aspect ratio of input signal.
Note:
True
•This projector cannot display any
Provide the image in its original size. When the original
image size is larger than the screen size (1280 x 800),
the projector automatically switches to the panning mode.
Use the Point ◄► ▲▼ buttons to pan the image. When
adjusted, the arrows turn red. When reached to the
correction limit, the arrows disappear.
resolution higher than 1600 x 1200. If your
computer’s resolution is higher than that,
lower the resolution before connecting to
the projector.
•The image data other than 1280 x 800
is modified to fit the screen size in initial
mode.
•True and D.Zoom+/- are not available
when the 4:3 or 16:9 function is selected in
the Screen aspect (p.44).
Full
Provide the full screen image.
•The items will be same as the items in
video source when 480i, 575i, 480p, 575p,
720p, 1035i or 1080i is selected in the PC
system Menu (p.26).
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer Input
Custom
Adjust the screen scale and position manually with this
function.
Press the SELECT button at Custom and the “Custom” is
displayed on the screen for a few seconds and then the
Aspect dialog box appears.
Scale H/V………Adjust the Horizontal/Vertical screen scale.
H&V ……………When set to “On,” the aspect ratio is fixed.
“Scale V” appears dimmed and becomes
unavailable. Adjust “Scale H,” then the
screen scale is automatically modified
based on the aspect ratio.
Press the SELECT button at
Common or Reset, to display
a confirmation box.
Position H/V……Adjust the Horizontal/Vertical screen
position.
Common……… Save the adjusted scale to all the inputs.
Press the SELECT button at Common to
display a confirmation box. To save the
scale, press the SELECT button at “Yes.”
When Custom is selected, the saved scale
is used.
Reset………… Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at “Yes.”
Note:
•When no signal is detected, “Normal” is
set automatically and the Aspect dialog
box disappears.
•The adjustable range for Scale H/V and
Position H/V is limited depending on the
input signal.
•When “Custom” is selected , “Digital zoom
-” is invalid.
Remote Control
POINT buttons
For zoomin� in and out the ima�es
Di�ital zoom +
SELECT button
D ZOOM + button
D ZOOM - button
When Digital zoom + is selected, the On-Screen Menu
disappears and “D. zoom +” is displayed. Press the
SELECT button to expand the image size. Use the Point
▲▼◄►buttons to pan the image. The Panning function
can work only when the image is larger than the screen
size.
Note:
•The minimum compression ratio can be
limited depending on the input signal or
when the Keystone function is working or
when the custom is selected for the screen
size.
•The items will be same as the items in
video source when 480i, 575i, 480p, 575p,
720p, 1035i or 1080i is selected in the PC
system Menu (p.26).
•Digital zoom +/– cannot be selected when
Full or True is selected.
•When “Custom” is selected , “Digital zoom
-” is invalid.
A projected image can be also expanded by pressing the
D.ZOOM ▲ button on the remote control.
Di�ital zoom –
When Digital zoom – is selected, the On-Screen Menu
disappears and “D. zoom –” is displayed. Press the
SELECT button to compress image size.
The projected image can be also compressed by pressing
the D.ZOOM ▼ button on the remote control.
To exit the Digital zoom +/– mode, press any button except
the D.ZOOM ▲▼, SELECT, and Point buttons.
•True and D.Zoom+/- are not available
when the 4:3 or 16:9 function is selected in
the Screen aspect (p.44).
To return to the previous screen size, select a screen size in
the Screen Size Adjustment or select an input source from
the Input Source Selection (p.25) again, or adjust the screen
size with the D.ZOOM ▲▼ buttons.
ꢁꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Video, S-video)
Top Control
Direct Operation
INPUT button
INPUT button
Select Video by pressing the INPUT button on the top
control or the VIDEO button on the remote control.
Before using INPUT or VIDEO button, select the correct
input source through menu operation as described below.
Video
Computer 1
Computer 2
*
*See Notes at the bottom of this page.
Remote Control
VIDEO button
Video
Menu Operation
Use the MENU button to display the On-Screen Menu.
Press the Point ◄► buttons to move the red frame
pointer to the Input Menu icon.
Input Menu icon
1
Input Menu
Use the Point ▲▼ buttons to move the red arrow
pointer to Video and then press the SELECT button to
display the Source Select Menu .
2
Move the pointer to Video and
press the SELECT button.
Move the pointer to the desired source and then press
the SELECT button.
3
VIDEO
When selecting “Auto,” the projector
automatically detects the incoming video signal,
and adjusts itself to optimize its performance.
The projector selects connection in the following
order:
Auto
Source Select Menu (VIDEO)
Move the pointer to the
desired source and press
the SELECT button.
1. S-video
2. Video
When the video input signal is connected to the
Video
VIDEO jack, select Video.
When the video input signal is connected to the
S-VIDEO jack, select S-video.
S-video
Note:
•Computer 2 is not displayed when the COMPUTER IN
2/MONITOR OUT terminal is set as Monitor out (p.44).
•When the Input Search function is set On1 or On2, the
input signal will be searched automatically (p.44).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Input Source Selection (Component, RGB Scart ꢀ1-pin)
Direct Operation
Top Control
INPUT button
INPUT button
Select Computer 1 by pressing the INPUT button on the top
control or COMPUTER button on the remote control.
Before using INPUT or COMPUTER button, select the
correct input source through Menu operation as described
below.
Computer 1
Computer ꢀ
*
Video
Remote Control
COMPUTER button
COMPUTER button
Computer 1
Computer ꢀ
*
*See Note at the bottom of this page.
Menu Operation
Use the MENU button to display the On-Screen Menu.
Press the Point ◄► buttons to move the red frame
pointer to the Input Menu icon.
1
Input Menu icon
Input Menu
Use the Point ▲▼ buttons to move the red arrow
pointer to Computer 1 and then press the SELECT
button.
2
Move the pointer (red arrow)
to Computer 1 and press the
SELECT button.
After the Source Select Menu appeared for Computer
1, move the pointer to Component or RGB (Scart) and
then press the SELECT button.
3
Computer
1
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/COMPONENT IN terminal with a
Component-VGA Cable (not supplied),
select Component.
Component
Source Select Menu
Move the pointer to Component
or RGB (Scart) and press the
SELECT button.
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/COMPONENT IN terminal with a
Scart-VGA Cable (not supplied), select
RGB (Scart).
RGB (Scart)
Note:
•Computer 2 is not displayed when the COMPUTER IN 2/
MONITOR OUT terminal is set as Monitor out (p.44).
•Computer 2 (COMPUTER IN 2/MONITOR OUT) can
accept only RGB signal.
• When the Input Search function is set On1 or On2, the
input signal will be searched automatically (p.44)
ꢁ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Video System Selection
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the AV System Menu icon.
1
2
Use the Point ▲▼ buttons to move the red arrow
pointer to the desired system and then press the
SELECT button.
AV System Menu (Video or S-video)
Video or S-video
Auto
The projector automatically detects an incoming video
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system
manually.
AV System Menu icon
The selected system is
displayed.
PAL/SECAM/NTSC/NTSC4 4ꢁ/PAL-M/PAL-N
Move the pointer to the
desired system and press
the SELECT button.
If the projector cannot reproduce proper video image,
select a specific broadcast signal format from among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
AV System Menu (Component)
Component
Auto
The projector automatically detects an incoming video
signal, and adjusts itself to optimize its performance.
AV System Menu icon
The selected system is
displayed.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select
a specific component video signal format from among 480i,
575i, 480p, 575p, 720p, 1035i, and 1080i.
Move the pointer to the
desired system and press
the SELECT button.
Note:
The AV System Menu cannot be selected when selecting
RGB (Scart).
ꢁ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Ima�e Level Selection
IMAGE button
Remote Control
Direct Operation
Select an image level from among Dynamic, Standard,
Cinema, Blackboard (Green), Colorboard, Image 1, Image
2, Image 3, and Image 4 with the IMAGE button on the
remote control.
Dynamic
Standard
Cinema
Dynamic
For viewing pictures in a bright room.
IMAGE
button
Standard
Blackboard(Green)
Colorboard
Ima�e 1
Normal picture level preset on this projector.
Cinema
Picture level adjusted for the picture with fine tone.
Blackboard (Green)
For viewing the image projected on a blackboard. This mode
assists to enhance the image projected on a blackboard.
This is mainly effective on a green colored board, not truly
effective on a black colored board.
Ima�e ꢀ
Ima�e ꢁ
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Ima�e 4
Image Select
Menu icon
Ima�e 1–4
User preset image in the Image Adjust Menu (pp. 38-39).
Ima�e Select Menu
Menu Operation
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Image Select Menu icon.
1
Move the red frame pointer to the
desired image level and press
the SELECT button.
Use the Point ▲▼ buttons to move the red frame
pointer to the desired level and then press the SELECT
button.
2
Dynamic
For viewing pictures in a bright room.
Standard
Normal picture level preset on this projector.
Cinema
Picture level with improved halftone for graphics.
The image level being selected.
Blackboard(Green)
For viewing the image projected on a blackboard. See
above for further description.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors. Press the SELECT button
to choose the color.
Ima�e 1–4
User preset image in the Image Adjust Menu (pp. 38-39).
ꢁ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Ima�e Level Adjustment
Press the MENU button to display the On-Screen Menu.
Use the Point ◄► buttons to move the red frame
pointer to the Image Adjust Menu icon.
Ima�e Adjust Menu
1
2
Use the Point ▲▼ buttons to move the red frame
pointer to the desired item and then press the SELECT
button. The level of each item is displayed. Adjust each
level by pressing the Point ◄► buttons.
Image Adjust Menu icon
Move the red frame pointer
to the desired item and then
press the SELECT button.
Contrast
Press the Point ◄ button to decrease the contrast; press
the Point ► button to increase the contrast (from 0 to 63).
Bri�htness
Press the Point ◄ button to decrease the brightness; press
the Point ► button to increase the brightness (from 0 to 63).
Color
Press the Point ◄ button to decrease the intensity of the
color; press the Point ► button to increase the intensity of
the color (from 0 to 63).
Use the Point ◄► buttons
to adjust the value.
Tint
Press the SELECT button
here to display other items.
Use the Point ◄► buttons to adjust the tint value to get a
proper color balance (from 0 to 63).
Color temp
Use the Point ◄► buttons to select the desired Color temp.
level (XLow, Low, Mid, or High).
White balance (Red)
Press the SELECT
button here to display
previous items.
Press the Point ◄ button to lighten the red tone; press the
Point ► button to deepen the red tone (from 0 to 63).
White balance (Green)
Press the Point ◄ button to lighten the green tone; press
the Point ► button to deepen the green tone (from 0 to 63).
White balance (Blue)
Press the Point ◄ button to lighten the blue tone; press the
Point ► button to deepen the blue tone (from 0 to 63).
Note:
•The Tint cannot be selected when the video system is
PAL, SECAM, PAL-M, or PAL-N.
•After adjusting the White balance Red, Green or Blue, the
Color temp. level will change to “Adj.”.
ꢁ8
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to get
better balance of contrast (from 0 to 15).
Noise reduction
Noise interference on the screen can be reduced. Select
one of the following options to get smoother images.
Off………Disabled.
L1 ………Lower reduction
L2 ………Higher reduction
Pro�ressive
An interlaced video signal can be displayed in a progressive
picture. Select one of the following options.
Off………Disabled.
L1……… For an active picture.
L2……… For a still picture.
Film…… For watching a film. With this function, the
projector reproduces pictures faithful to the
original film quality.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
“Yes.” All adjustments return to their previous figures.
Store
item
Image Level Menu
Move the red frame pointer to
an image item to be set and
then press the SELECT button.
Store
To store the adjusted data, select Store and press the
SELECT button. Select a level from Image 1 to 4 with
the Point ▲▼ buttons and press the SELECT button. A
confirmation box appears and then select “Yes.”
Stored data can be called up by selecting “Image” in the
Image Level Selection on page 37.
A confirmation box
appears and then
select “Yes.”
Quit
Exit the Image Adjust Menu.
Note:
Noise reduction and Progressive cannot be selected when
480p, 575p, 720p, 1035i, or 1080i is selected (p.36).
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Input
Screen Size Adjustment
This projector has the picture screen resize function, which enables you to customize the image size.
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Screen Menu icon.
Screen Menu
1
2
Screen Menu icon
Use the Point ▲▼ buttons and move the red frame
pointer to the desired function and then press the
SELECT button.
Move the red frame pointer to
the desired function and press
the SELECT button.
Normal
Provide the image to fit the screen size while maintaining
the aspect ratio of input signal.
Full
Provide the full screen image.
Zoom
Pan the horizontal direction of the image and cut the vertical
direction of the image to fit the screen size (16:9).Only for
4:3 video aspect ratio signals.
Wide
Provide the image at a wide screen ratio of 16:9.
Natural wide
Modify the 4:3 aspect ratio image to fit the screen size(16:9
aspect ratio) by stretching the image to make it look natural.
Custom
Adjust the screen scale and position manually.
Press the SELECT button at Custom icon. “Custom” is
displayed on the screen for a few seconds and then the
Aspect dialog box appears.
Press the SELECT button at
Common or Reset, to display
the confirmation box.
Scale H/V……… Adjust the Horizontal/Vertical screen scale.
H&V …………… When selecting “On,” the aspect ratio
is fixed. “Scale V” appears dimmed and
becomes unavailable. Adjust Scale H, then
the screen scale is automatically modified
based on the aspect ratio.
Note:
•Zoom, Wide and Natural wide are not
available when 720p, 1035i, or 1080i is
selected in the AV System Menu (p.36).
•When no signal is detected, Normal is
set automatically and Aspect dialog box
disappears.
•The adjustable range of Scale H/V and
Position H/V can be limited depending on
the input signal.
Position H/V……Adjust the Horizontal/Vertical screen
position.
Common ………Save the adjusted scale to all the inputs.
Press the SELECT button at Common to
display the confirmation box. To save the
scale, press the SELECT button at “Yes.”
When Custom is selected, the saved scale
is used.
Reset ………… Reset the all adjusted values. Press the
SELECT button at Reset to display the
confirmation box. To reset, press the
SELECT button at “Yes.”
• Zoom, Natural wide and Wide are not
available when the 4:3 or 16:9 function
is selected in the Screen aspect(p.44).
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Settin�
This projector has Setting menu that allows you to set up
Settin� Menu (Lan�ua�e)
the other various functions described as follows:
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Setting Menu icon.
1
Setting Menu
icon
Set the red framed
pointer to the item
and press the
Use the Point ▲▼ buttons to move the red frame
pointer to the item that you want to set and then press
the SELECT button. The Setting dialog box appears.
2
SELECT button.
Lan�ua�e
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Russian, Chinese, Korean, or Japanese.
Press the SELECT button
at Language item, the
Language Menu appears.
SELECT
button
Keystone
This function corrects distortion of a projected image.
Select either Store or Reset with the Point ◄► buttons,
and then press the SELECT button. The keystone dialog
box appears. Correct keystone with the Point ▲▼ buttons
(p.22).
Store……Store the keystone correction even when the
AC power cord is unplugged.
Reset……Reset the keystone correction when the AC
power cord is unplugged.
Blue back
Press the SELECT
button at this item
to display the other
languages.
Press the Point ◄► buttons to switch on/off. When this
function is “On,” a blue image is displayed while the input
signal is not detected.
Display
Press the Point ◄► buttons to switch on/off. This function
decides to display the On-Screen Displays.
On …………………Display all the On-Screen Displays.
Use this function when you want to
project images after the lamp becomes
bright enough. This mode is set as a
default.
Countdown off… Display the input image instead of
the countdown when turning on the
projector. Use this function when you
want to project the image as early as
possible even when the lamp is not
bright enough.
Press the SELECT
button at this item to
close the dialog box.
Off…………………Do not show the On-Screen Displays.
except:
● On-Screen Menu
● “Power off?”
● P-Timer
● “No signal” for Power management item (p.45)
● ”Please wait...”
● Arrows for panning mode (pp.32–33)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Lo�o select
Lo�o (Lo�o and Lo�o PIN code lock settin�s)
This function allows you to customize the screen logo with
Logo select, Capture, and Logo PIN code lock functions.
Note:
When “On” is selected in Logo PIN code lock function,
Logo select and Capture functions cannot be selected.
Lo�o select
This function decides the start-up display as follows:
User………The image you captured
Default……The factory-set logo
Off…………Countdown only
Capture
This function enables you to capture the image being
projected and use it for a start-up display or interval of
presentations.
Capture
After capturing the projected image, go to the Logo select
function and set it to “User.” Then the captured image is
displayed when the projector is turned on next time or the
NO SHOW button is pressed (p 24).
To capture the image, select “Yes.” To cancel the Capture
function, select “No.”
Note:
•Before capturing an image, select "Standard" in the
Image Select Menu to capture a proper image (pp.30,
37).
•A signal from a computer can be captured up to
WXGA(1280 x 800). A signal from video equipment
can be captured except for 720p, 1035i, and 1080i.
•When you capture the image that has been adjusted
by the Keystone or the Custom function, the adjusted
data is automatically reset and the projector captures
an image without keystone or custom adjustment.
•When the Logo PIN code lock function is “On,” Capture
menu cannot be selected.
Select "Yes" to capture
the projected image.
Select "Yes" to
stop capturing.
•When you start to capture a new image, the previously
stored image is cleared even if you cancel the
capturing.
•“User” cannot be selected when the image is not
captured.
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Logo PIN code lock
Logo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
Off……the screen logo can be changed freely from
the Logo select menu (p.42).
On……the screen logo cannot be changed without
the Logo PIN code.
If you want to change the Logo PIN code lock setting,
enter a Logo PIN code along the following steps. The
initial Logo PIN code is set “4321” at the factory.
Enter a Logo PIN code
Select a number by pressing the Point ▲▼ buttons.
And then press the Point ► button to fix the number
and move the pointer. The number changes to "". If
you fixed an incorrect number, move the pointer to the
number you want to correct by pressing the Point ◄
button, and then select the correct number by pressing
the Point ▲▼ buttons.
Logo PIN code lock Dialog Box
After a correct Logo PIN code is entered, the
following dialog box appears.
Repeat this step to complete entering a four-digit
number.
After entering the four-digit number, move the pointer to
"Set" by pressing the Point ► button. Press the SELECT
button so that you can change the following Logo PIN
code lock settings.
Select On/Off by pressing the Point ◄► buttons
or change the Logo PIN code.
Select Logo PIN code change by pressing the
Point ▼ button.
If you entered an incorrect PIN code, "Logo PIN code"
and the number () turns red. Enter a correct
Logo PIN code all over again.
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit
number. Select “Logo PIN code change” with the Point
▼ button and press the SELECT button. Set a new Logo
PIN code.
Be sure to note the new Logo PIN code and keep it on
hand. If you lost the number, you could no longer change
the Logo PIN code setting. For details on PIN code
setting, refer to relevant instructions of the PIN code lock
function on pages 47–48.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE,
WRITE DOWN THE NEW PIN CODE IN COLUMN OF
THE LOGO PIN CODE NO. MEMO ON PAGE 67, AND
KEEP IT SECURELY. SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE LOGO PIN CODE
SETTING CAN NO LONGER BE CHANGED.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Ceilin�
Rear
Ceilin�
When this function is set to “On”, the picture is top/bottom
and left/right reversed. This function is used to project the
image from a ceiling-mounted projector.
Rear
When this function is set to “On”, the picture is left/right
reversed. This function is used to project the image to a
rear projection screen.
Screen aspect
This function is used to project the image to a 4:3 or 16:9
projection screen.
4:3 ..... Set to a 4:3 projection screen.
16:9 ..... Set to a 16:9 projection screen.
16:10 ....16:10 is the aspect of the LCD panel. The orignal
Screen Menu is available.
Note:
•When the 4:3 or 16:9 function is selected,
True, Full and D.Zoom+/- are not available
in the PC screen (pp.32-33).
•When the 4:3 or 16:9 function is selected,
Zoom, Natural wide and Wide are not
available in the AV screen (p.40).
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back
of the projector is switchable for computer input or monitor
output (p.9). Select Computer 2 or Monitor Out with the
Point ◄► buttons.
Computer 2……computer input
Monitor Out……monitor out
Terminal function is not available when Computer 2 to the
input source is selected. Change the input source to the
others (Computer1 or Video) so that the Terminal function is
available (pp.25, 34–35).
Input search
This function detects the input signal automatically. When
finding a signal, the search will stop. Use the Point ◄►
buttons to select one of the following.
Off …… Input search does not work.
On1 …… Input search works under the situation below.
•When the COMPUTER button or VIDEO button
on the remote control is pressed.
On2 …… Input search works under the situation below.
•When the projector is turned on with pressing the
POWER ON/STAND-BY button on the remote
control. (After the countdown)
Note:
• While Input search is set On1 or On2, the
status of Input and Lamp are displayed
every time the signal is switched.
• Only the input source selected at the last
time can be detected.
• If COMPUTER/VIDEO button on the
remote control is pressed during Input
search is in progress, Input search will
stop.
•When the COMPUTER button or VIDEO button
on the remote control is pressed.
•When the current input signal is missed.
If the No show or Freeze function is active, cancel it
to activate the Input search. It is not available when
On-Screen menu is displayed.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Standby mode
This function is available when operating the projector via
network.
Normal........ Supply the power to the network function even
after turning off the projector You can turn on/ off
the projector via network, modify network
environment, and receive an e-mail about
projector status while the projector is powered
off.
Eco............. Select “Eco” when you do not use the projector
via network. The projector’s network function will
stop when turning off the projector.
Refer to the owner’s manual “Network Set-up and Operation”.
Note:
When selecting Normal, the cooling fans may be running
depending on the temperature inside the projector even if
the projector is turned off.
Power mana�ement
Power mana�ement
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the input signal is interrupted and no
button is pressed for a certain period.
Time left before Lamp is off.
When the input signal is interrupted and no button is
pressed for more than 30 seconds, the timer display with
“No signal” appears. The countdown starts to turn off the
lamp.
Select one of the operations.
Ready………When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition, the
projection lamp is turned on if the input
signal is reconnected or any button on the
remote control is pressed.
Shut down…When the lamp has been fully cooled down,
the power is turned off.
Off………… Power management function is off.
Press the SELECT button
at Power management and
this box appears. Select
one of three settings with
the Point ◄► buttons, and
go to the timer with the
Point ▲▼ buttons and set
time with the Point ◄►
buttons.
Then set the countdown timer with the Point ◄► buttons.
Note:
Factory default is “Ready: 5 min.”
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
On start
On start
When this function is set to “On,” the projector is
automatically turned on just by connecting the AC power
cord to an outlet.
Note:
Be sure to turn the projector off properly (see “Turning Off
the Projector” on page 19). If the projector is turned off
in the incorrect sequence, the On start function does not
operate properly.
Lamp control
You can change the brightness of the screen.
Normal … Normal brightness
Eco …… Lower brightness reduces the lamp power
consumption and extends the lamp life.
Note:
Lamp mode cannot be changed for a while after
turning on the projector. Lamp needs some time to
stabilize after the power is turned on. Stored lamp
mode will be active after the lamp is stabilized.
Remote control
Press and hold
MENU and
IMAGE buttons
for more than 5
seconds.
Remote control
This projector provides two different remote control codes;
the factory-set, initial code (Code 1) and the secondary code
(Code 2). This switching function prevents remote control
interference when several projectors or video equipment are
operated at the same time.
When the projector is operated in “Code 2,” both the
projector and the remote control must be switched to “Code
2.”
To chan�e the code for the projector:
Select either “Code 1” or “Code 2” in this Setting Menu.
To chan�e the code for the remote control:
Press and hold both the MENU and IMAGE buttons together
for more than 5 seconds. After changing the code, make
sure the remote control operates properly.
Note:
•When different codes are set on the projector and on the
remote control, any operation cannot be made. In that
case, switch the code on the remote control to fit the code
on the projector.
•If the batteries are removed from the remote control for a
long period of time, the remote control code will be reset.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Security (Key lock and PIN code lock settin�s)
This function allows you to use Key lock and PIN code lock
function to set the security for the projector operation.
Key lock
Key lock
This function locks operation of the top control or the
remote control.
It is useful to prevent operation by an unauthorized
person.
……not locked.
……lock the operation of the top control. To
unlock, use the remote control.
……lock the operation of the remote control.
To unlock, use the top control.
Select Key lock. Choose one of
the alternatives with the Point
▲▼ buttons and select [Yes] to
activate it.
If the top control accidentally becomes locked and you
do not have the romote control or there is something
wrong with your remote control, contact the dealer where
you purchased the projector or the service center.
PIN code lock
This function prevents the projector from being operated
by unauthorized persons and provides the following
setting options for security.
PIN code lock
Off…… The projector is not locked with the PIN code.
On1……Requires to enter a PIN code every time
turning on the projector.
On2……Requires to enter a PIN code to operate the
projector once the power cord is unplugged;
as long as the AC power cord is connected,
the projector can be operated without a
PIN code.
Whenever you change the PIN code lock setting or the
PIN code (a four-digit number), you are required to enter
the PIN code. “1234” is set as the initial PIN code at the
factory.
When the projector is locked
with the PIN code, the PIN code
lock symbol appears on the
menu bar.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Enter a PIN code
Enter a PIN code
Select a number by pressing the Point ▲▼ buttons.
And then press the Point ◄► button to fix the number
and move the pointer. The number changes to "". If
you fixed an incorrect number, move the pointer to the
number you want to correct by pressing the Point ◄►
button, and then select the correct number by pressing
the Point ▲▼ buttons.
Repeat this step to complete entering a four-digit
number.
The input numbers change
to “” for security reasons.
After entering the four-digit number, move the pointer
to "Set" by pressing the Point ◄► button. Press the
SELECT button so that you can change the following PIN
code lock settings. If you entered an incorrect PIN code,
"PIN code" and the number () turns red. Enter a
correct PIN code all over again.
Move the pointer to "Set" by
pressing the Point ► button.
And then press the SELECT
button.
Chan�e the PIN code lock settin�
Chan�e the PIN code lock settin�
Select Off, On1, or On2 with the Point ◄► buttons and
then move the red arrow pointer to “Quit” with the Point
▼ button. Press the SELECT button to close the dialog
box.
Select a desired setting with the
Point ◄► buttons.
Chan�e the PIN code
Chan�e the PIN code
The PIN code can be changed to your desired four-digit
number.
Select "PIN code change" with the Point ▼ button, and
press the SELECT button to display the New PIN code
input dialog box.
Select a number by pressing the Point ▲▼ buttons.
And then press the Point ► button to fix the number and
move the pointer. Repeat it to complete entering a four-
digit number. After entering the four-digit number, move
the pointer to "Set" by pressing the Point ► button. Then
press the SELECT button.
Select PIN code change and
press the SELECT button.
The New PIN code input
dialog box appears.
CAUTION:
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE
DOWN THE NEW PIN CODE IN COLUMN OF THE
PIN CODE NO MEMO ON PAGE 67, AND KEEP IT
SECURELY IF YOU FORGET YOUR PIN CODE, THE
PROJECTOR CAN NO LONGER BE STARTED
The input numbers are
being displayed for
confirmation.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Fan
This function provides the following options in the cooling
fans’ operation after turning off the projector (p.19).
L1 …… Normal operation
L2 …… Slower and lower-sound than the normal
operation (L1), but it takes longer to cool down
the projector.
Note:
Setting “Fan control” to On1 or On2 affects L2
operation in “Fan.”
Fan control
Choose the running speed of cooling fans from the following
options according to the ground elevation under which you
use the projector.
Off............ Normal speed. Set this function to “Off”
when using the projector in non-high altitude
environment.
Note:
• Fan noise becomes louder in On 1 and On2.
• Failure to set the running speed of cooling
fans properly may affect the projector life.
On 1......... Faster than Off mode. Select this mode when
using the projector in high altitudes (about
1,200 meters or more above the sea level)
where the fans have less cooling effect.
On 2......... Faster than On 1 mode. Select this mode
when using the projector in higher altitudes
than above where the fans have lesser cooling
effect.
Lamp replacement icon
Lamp counter
This function is used to reset the lamp replacement
counter. When replacing the projection lamp, reset the lamp
replacement counter by using this function. See page 55 for
operation.
This icon appears on the screen when the end of
lamp life is reached.
Note:
This icon also appears at turning on and
selecting input source.
Filter counter
This function is used to set a frequency for the filter
cleaning.
Fi� 1 Filter warning icon
When the projector reached a specified time between
cleanings, a Filter warning icon appears on the screen,
notifying the cleaning is necessary. After cleaning the filter,
be sure to select RESET and set the timer. The Filter
warning icon will not turn off until the filter counter is reset.
Filter warning icon appears on the screen at a set
time.
Note:
For details about resetting the timer, refer to “Resetting the
Filter Counter” on page 52.
This icon also appears at turning on.
Filter counter
Fi� ꢀ Filter warning icon
Note:
• At selecting input source, the icon (Fig.2)
will appear.
• The Filter warning icons (Fig.1 and Fig.2)
will not appear when the Display function
is set to “Off” (p.41), during
Use the Point ◄► buttons
to set the timer. Select
from (Off/100H/ 200H/
300H) depending on the
use environment.
“Freeze”(p.23), or "No show" (p.24).
4ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Settin�
Warnin� lo�
This function records anomalous operations while the
projector is in operation and use it when diagnosing faults.
Up to 10 warning logs are displayed with the latest warning
message at the top of the list, followed by previous warning
messages in chronological order.
Note:
When the Factory default function is executed, all the
warning log records will be deleted.
Closed Caption
Closed Caption
Closed Caption is a function that displays the audio portion
of a TV program as text on the screen.If the input signal
contains closed captions, you can turn on the feature and
switch the channels. Press the Point ◄► buttons to select
Off, CC1, CC2, CC3 or CC4.
If the closed caption is not clear, you can change the text
from Color to White.
Note:
The Closed Caption is available only under the situation
below.
• When the input signal is NTSC of composite and
S-video, and the system is set according to the
signal or set on "Auto".
• The system must be set on NTSC or Auto in Video
System Selection. (p.36)
• The icon of Closed Caption is displayed in gray
while it is not available.
• The closed caption is unavailable when On-Screen
menu and P-Timer are displayed.
Factory default
Factory Default
Factory default
This function returns all setting values except for the user
logo, PIN code lock, Logo PIN code lock, the lamp counter
and the filter counter to the factory default settings.
Select Factory default and
this box appears. Select
“Yes,” and the next box
appears.
Quit
Exit the Setting Menu.
Select “Yes” to
activate it.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleanin�
Warnin� Indicator
The WARNING indicator shows the state of the function which protects the projector. Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING
indicator is blinkin� red
WARNING
blinking red
Top Control
When the temperature inside the projector reaches a
certain level, the projector is automatically shut down to
avoid overheating. The POWER indicator is blinking while
the projector is being cooled down. When the projector has
cooled down enough (to its normal operating temperature),
it can be turned on again by pressing the POWER ON/
STAND-BY button.
Note:
The WARNING indicator continues to blink even after the
temperature inside the projector returns to normal. When
the projector is turned on again, the WARNING indicator
stops blinking.
Then check the matters below:
– Did you provide appropriate space for the projector to
be ventilated? Check the installing condition to see if
ventilation slots are not blocked.
– Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the
projector away from the duct or vent.
– Are the air filters clean? Clean the air filters periodically.
(p.52)
The projector is shut down and the WARNING
indicator li�hts red
WARNING
emit a red light
Top Control
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside of the projector
and the WARNING indicator lights red. In this case,
unplug the AC power cord and plug it, and then turn on
the projector once again to verify operation. If the projector
cannot be turned on and the WARNING indicator lights red,
unplug the AC power cord and contact the service station.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE
AC POWER CORD CONNECTED UNDER AN
ABNORMAL CONDITION. IT MAY RESULT IN FIRE
OR ELECTRIC SHOCK.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleanin�
Cleanin� the Air Filters
Air filters prevent dust from accumulating on the surface of the optical elements inside the projector. Should the
air filters become clogged with dust particles, they will reduce cooling fans’ effectiveness and may result in a
buildup of internal heat and adversely affect the life of the projector. Clean the air filters by following the steps
below.
Turn off the projector, and unplug the AC power cord
from the AC outlet.
1
Turn over the projector and remove the air filters by
pulling the latches upward.
2
Clean the air filters with a brush or rinse them softly.
When rinsing the air filters, dry them well.
3
Replace the air filters properly. Make sure that the air
filters are fully inserted.
4
CAUTION
Do not operate the projector with the air filters
removed. Dust may accumulate on the optical
elements degrading picture quality. Do not put
anything into the air intake vents. Otherwise it may
result in malfunction of the projector.
Air filters
Pull up and remove.
Note:
When reinserting the air filters, be sure that
the slit part is facing the outer side.
RECOMMENDATION
We recommend avoidin� dusty/smoky environments
when you operate the projector Usa�e in these
environments may cause poor ima�e quality
When you use the projector under dusty or smoky
conditions, dust may accumulate on the lens, LCD panels,
or optical elements inside the projector degrading the
quality of a projected image.
When the symptoms above are noticed, contact your
authorized dealer or service station for proper cleaning.
Resettin� the Filter Counter
Be sure to reset the Filter counter after cleaning or replacing the filters.
Press the MENU button to display the On-Screen
Menu. Use the Point ◄► buttons to move the red
frame pointer to the Setting Menu icon.
Filter counter
1
ꢀ
Select Reset and
the “Filter counter
Reset?” appears.
Use the Point ▲▼ buttons to move the red frame
pointer to Filter counter and then press the SELECT
button. A dialog box appears showing the total
accumulated time of the filter use, a timer setting
option, and the reset option. Select Reset and the
“Filter counter Reset?” appears. Select [Yes] to
continue.
Select [Yes],
then another
confirmation
box appears.
Another confirmation dialog box appears, select [Yes]
to reset the Filter counter.
ꢁ
Select [Yes] again
to reset the Filter
counter.
5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleanin�
Attachin� the Lens Cover
1
2
When moving the projector or while it is not in use, replace
the lens cover.
Thread the string through the hole on the lens cover
and then tie a knot in the string to secure it in place.
1
Thread the other end of the string through the hole on
the bottom of the projector. Then pass the lens cover
through the resulting loop of the string and pull it to
tighten the knot.
2
Cleanin� the Projection Lens
CAUTION
This projector is equipped with a plastic lens.
Do not rub the lens with a hard fiber cloth or hit it with something hard to prevent the lens from scratching.
Do not use a chemical cleaner (liquid and solid) to avoid deteriorating the lens.
Unplug the AC power cord before cleaning.
First, remove the dust with a blower. Then gently wipe the
lens surface. Use a lens cleaning paper moistened with
methyl alcohol (methanol). Avoid excessive use of cleaner.
Do not use abrasive cleaners, solvents, or other harsh
chemical cleaners to avoid damages the lens.
When the projector is not in use, replace the lens cover.
Cleanin� the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning
cloth. When it is heavily soiled, use a small amount of mild
detergent and finish with the cleaning cloth. Avoid excessive
use of cleaner. Abrasive cleaners, solvents, or other harsh
chemicals might scratch the surface of the cabinet.
When the projector is not in use, put the projector in an
appropriate case to avoid dust and being scratched.
5ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleanin�
Lamp Replacement
This indicator
turns yellow
when the
projection lamp
reaches the end
of its life.
When the projection lamp of the projector reaches the end
of its life, the LAMP REPLACE indicator emits a yellow light.
If this indicator lights yellow, replace the lamp with a new
one promptly.
Top Control
WARNING:
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER
Lamp replacement icon
Note:
The Lamp replacement icon will not appear
when the Display function is set to “Off” (p.41),
during “Freeze” (p.23), or “No show” (p.24).
CAUTION
Allow the projector to cool for at least 45 minutes
before you open the Lamp cover. The inside of the
projector can become very hot.
CAUTION
For continued safety, replace with a lamp of the
same type. Do not drop a lamp or touch a glass
bulb! The glass can shatter and may cause injury.
Screw
Lamp Cover
Follow these steps to replace the lamp.
Turn off the projector and unplug the AC power cord.
Let the projector cool for at least 45 minutes.
1
Turn the projector over. Remove the screw that
secures the lamp cover, and then open the lamp cover.
2
Loosen the two screws that secure the lamp. Lift the
lamp out of the projector by using the built in handle.
3
Screw
Replace the lamp with a new one and secure it with the
two screws. Make sure that the lamp is set properly.
Put the lamp cover back and secure it with the screw.
Lamp
4
Screw
Connect the AC power cord to the projector and turn
5
on the projector.
Handle
Reset the lamp replacement counter
See “Lamp Replacement Counter” on the next page.
6
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following
information to the dealer.
●Model No of your projector : PLC-WXE46
●Replacement Lamp Type No : POA-LMP106
(Service Parts No. 610 332 3855)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleanin�
Lamp Replacement Counter
Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement counter
is reset, the LAMP REPLACE indicator stops lighting.
Lamp counter
Turn the projector on and press the MENU button
to display the On-Screen Menu. Use the Point ◄►
buttons to move the red frame pointer to the Setting
1
Lamp counter
To reset the lamp counter,
move the pointer to
Menu icon.
Reset and then press
Use the Point ▲▼ buttons to move the red frame
pointer to Lamp counter and then press the SELECT
button. The first dialog box appears showing the total
accumulated lamp time and reset option. If you select
Reset, “Lamp replacement counter Reset?” appears.
Select “Yes” to continue.
the SELECT button. the
“Lamp replacement counter
Reset?” dialog box appears.
2
Select “Yes,” then
another confirmation
box appears.
Another confirmation dialog box appears, and select
“Yes” to reset the Lamp replacement counter.
3
Select “Yes” again to reset
the lamp counter.
Note:
Do not reset the Lamp replacement counter without
implementing lamp replacement. Be sure to reset the
Lamp replacement counter only after replacing the lamp.
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
●Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee
of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period of time than
other similar lamps.
●If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
(Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.
●A Lamp may explode as a result of vibration, shock, or degradation as a result of hours of use, as it
comes to the end of life. Risk of explosion may differ according to the environment or conditions in which
the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Troubleshootin�
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described on pages 14-16.
– Make sure all equipment is connected to the AC outlet and the power is turned on.
– When you operate the projector with a computer and it does not project an image, restart the computer.
– Solutions
Problem:
No power
– Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
– Wait until the POWER indicator stops blinking to turn on the
projector again. The projector can be turned on after the POWER
indicator turns red (see page 19).
– Check the WARNING indicator. If the WARNING indicator lights
red, the projector cannot be turned on (see on page 51).
– Check the projection lamp (see page 54).
PIN code dialo� box appears at
start-up
– PIN code lock is being set. Enter a PIN code; the “1234” or
numbers you have set (see pages 18, 47–48).
– Make sure "Off" or "Countdown Off" are not chosen at Display
function (see page 41).
The initial display is not shown
The initial display is not same with
the default one
– Make sure "User" or "Off" are not chosen at Logo function (see
page 42).
Input si�nal switches automatically – Make sure Input search function is adjusted properly (see page
(or does not switch automatically)
44).
– Check the connection between your computer or video equipment
and the projector (see pages 14-16)
– See if the input signal is correctly output from your computer. Some
laptop computers may need to be changed the setting for monitor
output when connected to the projector. See your computer’s
instruction manual for the setting
– It takes about 30 seconds to display an image after turning on the
projector.
– See if the selected system is corresponding with your computer or
video equipment (see pages 26, 36)
No ima�e
– Select correct input source once again through menu operation
(see pages 25 ,34–35).
– Make sure the temperature is not out of the specified operating
temperature (41 ˚F–95 ˚F [5 ˚C–35 ˚C]).
– When "No Show" is operating, the image can not be displayed.
Press the NO SHOW button or any other button on the remote
control.
– Adjust focus of the projector (see page 22).
– Provide proper distance between the projector and the projection
screen (see page 13).
– Check the projection lens to see if it needs cleaning (see page 53).
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. If this occurs, leave
the projector off and wait until condensation evaporates.
– Projecting from the excessive slant angel to the screen may cause
keystone distortion and partial imperfect focus.
Ima�e is out of focus
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
– Check if "Contrast" or "Brightness" are adjusted properly (see
pages 31, 38).
– Check if "Image level" is selected properly (see pages 30, 37).
– Check the LAMP REPLACE indicator. If it lights, the end of lamp
life is approaching. Replace the lamp with a new one promptly
(see pages 54-55, 61).
Picture is not bri�ht enou�h
– Check the Lamp control function (see pages 24, 46).
– Check the Input signal, color system, video system, or computer
system mode.
The color is stran�e
– Adjust the Image level properly (see pages 31, 38).
Ima�e is Left/Ri�ht reversed
Ima�e is Top/Bottom reversed
– Check the Ceiling/Rear function (see page 44).
– Check the Ceiling function (see page 44).
– Check the PC Adjustment menu or Screen menu and adjust them
(see pages 26-29, 32-33, 40).
The ima�e is distorted or runs off
– Check the audio cable connection from audio input source.
– Adjust the audio source.
– Press the Volume + button (see page 23).
– Press the Mute button (see page 23).
– When the AUDIO OUT is plugged in, the projector's built-in
No sound
speaker is not available.
– Is the image projected? You will hear the sound only when the
image is projected.
Some displays are not seen durin�
the operation
– Check the Display function (see page 41).
– Check the Input signal. Auto PC Adjustment function can not work
when 480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected (see
page 27).
Auto PC adjustment function does
not work
The settin� does not remain after
turnin� off power
– Make sure you selected “Store” after adjusting settings. Some
settings cannot be stored if not registered with “Store.”
Power mana�ement function does
not work
– Power management function cannot work while "Freeze" or "No
Show" function is running.
– Check the power management function in the Setting. The power
management is set to “On” at the factory.
Ima�e disappears automatically
Capture function does not work
– Check the connection and the Input signal to see if there is signal.
– Check the batteries.
– Make sure no obstruction is between the projector and the remote
control.
– Make sure you are not too far from the projector when using the
remote control. Maximum operating range is 16.4’ (5 m).
– Make sure the code of the remote control is conformed to that of
the projector (see page 46).
The Remote Control does not work
– Unlock the Key lock function for the remote control (see page 47).
– Unlock the Key lock function for the top control of the projector
(see page 47).
The top control does not work
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
– Check the status of the projector with referring to "indicators and
Projector Condition" (see page 61).
Indicator blinks or li�hts
Computer ꢀ cannot be selected
– Select Computer 2 in the Terminal function (see page 44).
– The Terminal function cannot be selected after Computer 2 is
selected. Select other input source such as Computer 1 or Video
with the COMPUTER button or the VIDEO button on the remote
control so that the Terminal function can be selected.
The terminal function cannot be
selected
The exclamation mark appears on
the screen
– Your operation is invalid. Operate correctly.
Unable to unlock the Lo�o PIN code – Contact the dealer where you purchased the projector or the
lock or Security PIN code lock
service center.
WARNING :
Hi�h volta�es are used to operate this projector Do not attempt to open the cabinet
If problems still persist after following all operating instructions, contact the dealer where you purchased the
projector or the service center. Specify the model number and explain about the problem. We will advise you
how to obtain service.
This symbol on the nameplate means the product
The CE Mark is a Directive
conformity mark of the European
Community (EC).
is Listed by Underwriters Laboratories Inc. It is
designed and manufactured to meet rigid U.L.
safety standards against risk of fire, casualty and
electrical hazards.
Pixelworks ICs used.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Menu Tree
Computer Input/Video Input
Computer 1
RGB
Go to System (1)
Input
Component
Go to System (2)
RGB( Scart )
Quit
Computer 2
Video
Go to System (1)
Auto
Go to System (3)
Go to System (3)
Go to System (3)
Video
S-video
Quit
Sound
Volume
Mute
0 - 63
On / Off
Sound
Quit
Computer Input
System (1)
Mode 1
Mode 2
SVGA 1
- - - -
Systems displayed in the System Menu vary
depending on an input signal.
PC Adjust
Auto PC adj.
Ima�e Adjust
Contrast
0 - 63
0 - 63
XLow
Low
Fine sync
Total dots
Horizontal
Vertical
Brightness
Color temp.
0 - 31
Mid
Current mode
Clamp
H-sync freq.
V-sync freq.
Quit
High
Adj.
Red
0 - 63
0 - 63
0 - 63
0 - 15
0 - 15
Yes / No
Image 1
Image 2
Image 3
Image 4
Quit
Display area H
Display area V
Reset
Green
Blue
Yes / No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Sharpness
Gamma
Reset
Store
Mode free
Store
Quit
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Quit
Screen
Normal
True
Full
Custom
Scale H / V
Ima�e Select
Dynamic
Standard
Real
H&V
On / Off
Position H / V
Common Yes / No
Blackboard (Green)
Colorboard
Image 1
Reset
Quit
Yes / No
Digital zoom +
Digital zoom –
Image 2
Image 3
Image 4
5ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Video Input
Setting
System (2)
Auto
1080i
1035i
720p
575p
480p
575i
Setting
Language
16 languages provided.
Quit
Keystone
Blue back
Display
Logo
Store / Reset
On / Off
Off / Countdown off / On
Logo select
Off
480i
Default
User
System (3)
Auto
Capture
PAL
Yes / No
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
Logo PIN code lock
On / Off
Logo PIN code change
Quit
Quit
Ceiling
On / Off
Image Select
Dynamic
Standard
Cinema
Rear
Screen aspect
On / Off
4:3 / 16:9 / 16:10
Blackboard (Green)
Colorboard
Image 1
Terminal
Computer 2 / Monitor out
Input Search
Standby mode
Off / On1 / On2
Eco / Normal
Image 2
Power management
Off
Image 3
Ready
Image 4
Shut down
Timer(1-30 Min)
Quit
Image Adjust
Contrast
Brightness
Color
0 - 63
0 - 63
0 - 63
0 - 63
XLow
Low
Mid
On start
On / Off
Tint
Lamp control
Remote control
Normal / Eco
Code 1 / Code 2
Color temp.
Security
Key lock
High
Adj.
PIN code lock
Off / On1 / On2
Red
0 - 63
0 - 63
0 - 63
0 - 15
0 - 15
Off
PIN code change
Green
Quit
Quit
Blue
Sharpness
Gamma
Noise reduction
Fan
L1 / L2
Fan control
Off / On1 / On2
L1
Lamp counter
Hour(s)
Reset
Quit
L2
Progressive
Off
Hour(s)
Filter counter
L1
Off / 100H / 200H / 300H
L2
Reset
Quit
Yes / No
Film
Warning log
Reset
Store
Yes / No
Image 1
Image 2
Image 3
Image 4
Quit
Off / CC1 / CC2 / CC3 / CC4
Closed caption
Color / White
Quit
Factory default
Quit
Yes / No
Quit
Screen
Normal
Full
Zoom
Wide
Natural wide
Custom
Scale H / V
H&V
On / Off
Position H / V
Common
Reset
Yes / No
Yes / No
Quit
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Indicators and Projector Condition
Check the indicators for projector condition.
Indicators
LAMP
REPLACE
yellow
Projector Condition
POWER
red/�reen
WARNING
red
The projector is off. (The AC power cord is unplugged.)
The projector is preparing for stand-by or the projection lamp is
being cooled down. The projector cannot be turned on until cooling is
completed.
The projector is ready to be turned on with the POWER ON/STAND-BY
button.
The projector is operating normally.
The projector is in the Power management mode.
The temperature inside the projector is abnormally high. The projector
cannot be turned on. When the projector is cooled down enough and
the temperature returns to normal, the POWER indicator lights red
and the projector can be turned on. (The WARNING indicator keeps
blinking.) Check and clean the air filters.
The projector has been cooled down enough and the temperature
returns to normal. When turning on the projector, the WARNING
indicator stops blinking. Check and clean the air filters.
The projector detects an abnormal condition and cannot be turned on.
Unplug the AC power cord and plug it again to turn on the projector. If
the projector is turned off again, unplug the AC power cord and contact
the dealer or the service center for service and checkup. Do not leave
the projector on. It may cause an electric shock or a fire hazard.
• • • green.
• • • blinks green.
• • • red
• • • blinks red.
• • • off
When the projection lamp reaches the end of its life, the LAMP REPLACE indicator lights yellow.
When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp
replacement counter after replacing the lamp. See pages 54-55.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Compatible Computer Specifications
Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below
and less than 140 MHz of Dot Clock.
When selecting these modes, Screen, Auto PC adjustment and PC adjustment can be limited.
ON-SCREEN
DISPLAY
H-Freq
(kHz)
V-Freq
(Hz)
ON-SCREEN
DISPLAY
H-Freq
(kHz)
V-Freq
(Hz)
RESOLUTION
RESOLUTION
SXGA6
SXGA7
SXGA8
SXGA9
SXGA10
SXGA11
SXGA12
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1152x900
1152x900
71.69
81.13
63.98
79.976
60.00
61.20
71.40
67.19
76.107
60.02
75.025
60.00
65.20
75.60
VGA1
VGA2
640x480
720x400
640x400
640x480
640x480
640x480
640x480
640x480
640x480
640x480
768x575
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
31.47
31.25
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
59.88
50.00
VGA3
VGA4
VGA5
VGA6
VGA7
86.00
MAC LC13
MAC 13
480p
SXGA13
SXGA14
1280x1024
1280x1024
50.00
50.00
(Interlace)
94.00
(Interlace)
SXGA15
SXGA16
SXGA17
1280x1024
1280x1024
1152x900
63.37
76.97
61.85
60.01
72.00
66.00
575p
50.00
575i
480i
768x576
640x480
15.625
15.734
(Interlace)
60.00
86.70
(Interlace)
SXGA18
1280x1024
46.43
(Interlace)
SVGA1
SVGA2
SVGA3
SVGA4
SVGA5
SVGA6
SVGA7
SVGA8
SVGA9
SVGA10
SVGA11
MAC16
XGA1
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
800x600
832x624
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
SXGA19
SXGA20
SXGA+ 1
SXGA+ 2
SXGA+ 3
MAC21
1280x1024
1280x1024
1400x1050
1400x1050
1400x1050
1152x870
1280x960
1280x1024
1366x768
1360x768
1376x768
1360x768
1280x768
1280x768
1280x768
1280x800
1280x800
1280x800
1920 x 1200
1920 x 1200
1680 x 1050
1440 x 900
1440 x 900
1600x1200
1600x1200
1600x1200
1600x1200
1280x720
1280x720
63.79
91.146
63.979
65.346
65.121
68.68
60.18
85.024
60.190
60.116
59.902
75.06
MAC
75.00
75.08
MAC
80.00
75.08
WXGA1
WXGA2
WXGA3
WXGA4
WXGA6
WXGA7
WXGA8
WXGA9
WXGA10
WXGA 11
WUXGA 1
WUXGA 2
WSXGA+ 1
WXGA+ 1
WXGA+ 2
UXGA1
UXGA2
UXGA3
UXGA4
720p
48.36
60.00
47.70
60.00
48.36
60.00
56.16
72.00
47.776
60.289
68.633
49.600
41.20
59.870
74.893
84.837
60.050
50.00
XGA2
XGA3
XGA4
XGA5
XGA6
49.702
74.556
74.038
65.290
55.935
74.918
75.00
59.810
59.885
59.950
59.954
59.887
60.000
60.00
XGA7
XGA8
87.17
XGA9
1024x768
36.00
(Interlace)
XGA10
XGA11
1024x768
1024x768
62.04
61.00
77.07
75.70
86.96
XGA12
1024x768
35.522
(Interlace)
81.25
65.00
XGA13
XGA14
XGA15
MAC19
SXGA1
SXGA2
SXGA3
SXGA4
SXGA5
1024x768
1024x768
1024x768
1024x768
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
46.90
47.00
58.03
60.24
64.20
62.50
63.90
63.34
63.74
58.20
58.30
72.00
75.08
70.40
58.60
60.00
59.98
60.01
87.5
70.00
93.75
75.00
37.50
50.00
720p
45.00
60.00
60.00
1035i
1080i
1080i
1920x1035
1920x1080
1920x1080
33.75
33.75
(Interlace)
60.00
(Interlace)
50.00
28.125
(Interlace)
6ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Specifications
Mechanical Information
Projector Type
Multi-media Projector
Dimensions (W x H x D)
Net Weight
12.59" x 5.73" x 11.85" (319.9 mm x 145.5 x 300.9 mm) (Not including protrusions)
7.5 lbs (3.4 kg)
0˚ to 10.0˚
Feet Adjustment
Panel Resolution
LCD Panel System
Panel Resolution
0.59” TFT Active Matrix type, 3 panels
1,280 x 800 dots
Number of Pixels
3,072,000 (1,280 x 800 x 3 panels)
Si�nal Compatibility
Color System
PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, and 1080i
H-sync. 15–100 kHz, V-sync. 50–100 Hz
High Definition TV Signal
Scanning Frequency
Optical Information
Projection Image Size (Diagonal)
Projection Lens
Adjustable from 50” to 110”
F 1.8 lens with f 6.6 mm with manual focus
1.77' - 3.94' (0.53 m - 1.20 m)
200 W
Throw Distance
Projection Lamp
Interface
Video Input Jack
RCA Type x 1
S-Video Input Jack
Mini DIN 4 pin x 1
Audio Input Jacks
RCA Type x 2
Computer Input 1 / Component Input Terminal
Computer Input 2 / Monitor Output Terminal
Computer/ Component Audio Input Jack
Service Port Connector
LAN Connection Terminal
Audio Output Jack
Analog RGB (Mini D-sub 15 pin) Terminal x 1
Analog RGB (Mini D-sub 15 pin) Terminal x 1 (In/Out switchable)
Mini Jack (stereo) x 1
Mini DIN 8 pin x 1
100 Base-TX (100Mbps)/10Base-T (10Mbps), RJ45
Mini Jack (stereo) x 1 (Variable)
Audio
Internal Audio Amp
1.0 W RMS
Built-in Speaker
1 speaker, ø1.1” (28 mm)
Power
Voltage and Power Consumption
AC 100–120 V (3.2 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)
AC 200–240 V (1.6 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)
Operatin� Environment
Operating Temperature
Storage Temperature
41˚F–95˚F (5˚C–35˚C)
14˚F–140˚F (-10˚C–60˚C)
Remote Control
Battery
AA or LR6 1.5V ALKALINE TYPE x 2
16.4’ (5 m)/±30˚
Operating Range
Dimensions
1.9” (W) x 0.87” (H) x 5.7” (D) (49 mm x 22 mm x 145.3 mm)
3.53 oz (100 g) (including batteries)
Net Weight
6ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Accessories
Owner’s Manual(CD-ROM)
Network Application (CD-ROM)
Quick Reference Guide
AC Power Cord
Remote Control and Batteries
VGA Cable
Lens Cover with String
PIN Code Label
● The specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are
effective, a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
Optional Parts
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No.
to the sales dealer.
Model No.
COMPONENT~VGA Cable
SCART~VGA Cable
VGA-Cable (10 m)
: POA-CA-COMPVGA
: POA-CA-SCART
: KA-MC-DB10
Dimensions
Unit: inch (mm)
Screw Holes for Ceiling Mount
Screw: M4
Depth: 0.472 (12.0)
12.6 (320)
3.1 (80)
4.3 (108)
2.4 (60)
4.3 (108)
3.4 (105)
5.1 (130.6)
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
PJ Link Notice
This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information
System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified
conformance with PJLink Standard Class 1.
For PJ Link password, see page 21 on the owner’s manual “Network Set-up and Operation.”
Projector Input
Computer1
PJLink Input
RGB 1
Parameter
RGB
11
12
13
14
21
22
23
Component
RGB (Scart)
RGB
RGB 2
RGB 3
RGB 4
Computer2
Video
Auto
VIDEO 1
VIDEO 2
VIDEO 3
Video
S-video
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Confi�urations of Terminals
COMPUTER INPUT/COMPONENT INPUT/MONITOR OUTPUT TERMINAL (ANALOG)
Terminal : Analo� RGB (Mini D-sub 15 pin)
Red (R/Cr) Input / Output
Green (G/Y) Input / Output
Blue (B/Cb) Input / Output
/
1
ꢀ
ꢁ
4
5
6
7
8
ꢂ
+5V Power -----
2
1
5
4
3
Ground (Vert.sync.)
10
11
10
9
8
7
6
15
12
11
14
13
Ground /
-----
/
-----
Ground (Horiz.sync.)
Ground (Red)
1ꢀ DDC data -----
Horiz. sync. Input/Output (Composite H/V sync.)
1ꢁ
14
Vert. sync.
Ground (Green)
Ground (Blue)
/
15 DDC clock -----
SERVICE PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Serial
1
ꢀ
ꢁ
4
5
6
7
8
R X D
-----
8
7
6
5
4
3
2
1
-----
GND
RTS / CTS
T X D
GND
GND
LAN TERMINAL
1
ꢀ
ꢁ
4
TX +
TX –
RX +
-----
5
-----
RX –
-----
6
7
8
-----
87 6 54 32 1
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
PIN Code Number Memo
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost
the number and unable to operate the projector, contact the service station.
PIN Code Lock No
Factory default set No: 1 2 3 4*
Lo�o PIN Code Lock No
Factory default set No: 4 3 2 1*
While the projector is locked with the PIN code...
Put the label below (supplied) to a prominent place of the
projector’s body while it is locked with a PIN code.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
KM5AY
SANYO Electric Co , Ltd
Download from Www.Somanuals.com. All Manuals Search And Download.
|
