Sanyo Projection Television PDG DXT10KL User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.  
To the Owner  
Before installing and operating the projector, read this  
manual thoroughly.  
Safety Precaution  
The projector provides many convenient features and  
functions. Operating the projector properly enables you  
to manage those features and maintains it in good condi-  
tion for many years to come.  
Improper operation may result in not only shortening the  
product life, but also malfunctions, fire hazard, or other  
accidents.  
If your projector seems to operate improperly, read this  
manual again, check operations and cable connections  
and try the solutions in the “Troubleshooting” section in  
the back of this booklet. If the problem still persists, con-  
tact the dealer where you purchased the projector or the  
service center.  
WARNING:  
TO REDUCE THE RISK OF FIRE OR ELECTRIC  
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO  
RAIN OR MOISTURE.  
ꢁꢀ This projector produces intense light from the projec-  
tion lens. Do not stare directly into the lens as much  
as possible, otherwise eye damage could result. Be  
especially careful that children do not stare directly  
into the beam.  
ꢁꢀ Install the projector in a proper position. Otherwise it  
may result in fire hazard.  
ꢁꢀ Allowing the proper amount of space on the top,  
sides, and rear of the projector cabinet is critical for  
proper air circulation and cooling of the unit. The di-  
mension shown here indicates the minimum space  
required.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE COVER (OR  
BACK). NO USER-SERVICEABLE PARTS  
INSIDE EXCEPT LAMP REPLACEMENT.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
If the projector is to be built into a compartment or  
similarly enclosed, these minimum distances must be  
maintained.  
ꢁꢀ Do not cover the ventilation slot on the projector.  
Heat build-up can reduce the service life of your  
projector, and can also be dangerous.  
THIS SYMBOL INDICATES THAT  
DANGEROUS VOLTAGE CONSTITUTING A  
RISK OF ELECTRIC SHOCK IS PRESENT  
WITHIN THIS UNIT.  
SIDE and TOP  
REAR  
THIS SYMBOL INDICATES THAT THERE  
ARE IMPORTANT OPERATING AND  
MAINTENANCE INSTRUCTIONS IN THE  
USER’S MANUAL WITH THIS UNIT.  
ꢁꢀ If the projector is unused for an extended time,  
unplug the projector from the power outlet.  
NOTE: This symbol and recycle system are applied  
only to EU countries and not applied to the  
countries in the other area of the world.  
CAUTION ON HANGING FROM THE CEILING  
When hanging the projector from the ceil-  
ing, clean air intake vents, filters, or top of  
the projector periodically with a vacuum  
cleaner. If you leave the projector unclean  
for a long time, the cooling fans can be  
clogged with dust, and it may cause a  
breakdown.  
Your SANYOproductisdesignedand manu-  
factured with high quality materials and  
components which can be recycled and  
reused.  
Thissymbolmeansthat electricaland elec-  
tronic equipment, at their end-of-life, should  
be disposed ofseparatelyfrom your house-  
hold waste.  
DO NOT SET THE PROJECTOR IN GREASY, WET, OR  
CONDITIONS SUCH AS IN A KITCHEN TO PREVENT  
A BREAKDOWN. IF THE PROJECTOR COMES IN  
CONTACT WITH OIL OR CHEMICALS, IT MAY  
BECOME DETERIORATED.  
Please dispose of this equipment at your local commu-  
nity waste collection/recycling centre.  
In the European Union there are separate collection  
systems for used electrical and electronic products.  
Please help us to conserve the environment we live in!  
WARNING:  
Not for use in a computer room as defined in the Stan-  
dard for the Protection of Electronic Computer/Data  
Processing Equipment, ANSI/NFPA 75.  
Ne peut être utilisé dans une salle d’ordinateurs telle que  
définie dans la norme ANSI/NFPA 75 Standard for Pro-  
tection of Electronic Computer/Data Processing  
Equipment.  
READ AND KEEP THIS USER’S MANUAL FOR LATER  
USE.  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Instructions  
All the safety and operating instructions should be read  
before the product is operated.  
Do not install the projector near the ventilation duct of air-  
conditioning equipment.  
Read all of the instructions given here and retain them for  
later use. Unplug this projector from AC power supply  
before cleaning. Do not use liquid or aerosol cleaners.  
Use a damp cloth for cleaning.  
This projector should be operated only from the type of  
power source indicated on the marking label. If you are  
not sure of the type of power supplied, consult your au-  
thorized dealer or local power company.  
Follow all warnings and instructions marked on the pro-  
jector.  
Do not overload wall outlets and extension cords as this  
can result in fire or electric shock. Do not allow anything to  
rest on the power cord. Do not locate this projector where  
the cord may be damaged by persons walking on it.  
For added protection to the projector during a lightning  
storm, or when it is left unattended and unused for long  
periods of time, unplug it from the wall outlet. This will  
prevent damage due to lightning and power line surges.  
Do not attempt to service this projector yourself as open-  
ing or removing covers may expose you to dangerous  
voltage or other hazards. Refer all servicing to qualified  
service personnel.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool,  
etc...  
Unplug this projector from wall outlet and refer servicing  
to qualified service personnel under the following condi-  
tions:  
Do not use attachments not recommended by the manu-  
facturer as they may cause hazards.  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not place this projector on an unstable cart, stand, or  
table. The projector may fall, causing serious injury to a  
child or adult, and serious damage to the projector. Use  
only with a cart or stand recommended by the manufac-  
turer, or sold with the projector. Wall or shelf mounting  
should follow the manufacturer’s instructions, and should  
use a mounting kit approved by the manufacturers.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by follow-  
ing the operating instructions. Adjust only those  
controls that are covered by the operating instruc-  
tions as improper adjustment of other controls may  
result in damage and will often require extensive  
work by a qualified technician to restore the projector  
to normal operation.  
An appliance and cart combination  
should be moved with care. Quick  
stops, excessive force, and uneven sur-  
faces may cause the appliance and cart  
combination to overturn.  
e. If the projector has been dropped or the cabinet has  
been damaged.  
f. When the projector exhibits a distinct change in per-  
formance-this indicates a need for service.  
When replacement parts are required, be sure the ser-  
vice technician has used replacement parts specified by  
the manufacturer that have the same characteristics as  
the original part. Unauthorized substitutions may result in  
fire, electric shock, or injury to persons.  
Slots and openings in the back and bottom of the cabinet  
are provided for ventilation, to ensure reliable operation  
of the equipment and to protect it from overheating.  
The openings should never be covered with cloth or  
other materials, and the bottom opening should not be  
blocked by placing the projector on a bed, sofa, rug, or  
other similar surface. This projector should never be  
placed near or over a radiator or heat register.  
Upon completion of any service or repairs to this projec-  
tor, ask the service technician to perform routine safety  
checks to determine that the projector is in safe operating  
condition.  
This projector should not be placed in a built-in installa-  
tion such as a bookcase unless proper ventilation is  
provided.  
V
oor de klanten in Nederland  
Bij dit produkt zijn batterijen ge-  
leverd.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points  
or short out parts that could result in a fire or electric  
shock. Never spill liquid of any kind on the projector.  
Wanneerdezeleeg zijn, moet u ze  
niet weggooien maar inleveren als  
KCA.  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Information  
Air Circulation  
Openings in the cabinet are provided for ventilation. To  
ensure reliable operation of the product and to protect it  
from overheating, these openings must not be blocked or  
covered.  
IMPORTANT!  
Clean the Filter Regularly!!  
The projector uses a lamp which generates significant  
heat. The cooling fans and air vents are provided to dis-  
sipate the heat by drawing air into the housing and the  
filter is located in the intake vents to prevent dust from  
getting inside of the projector.  
CAUTION  
Hot air is from the exhaust vent. When using or installing  
the projector, the following precautions should be taken.  
In order to care for the projector appropriately, regular  
cleaning is required. Remove any dirt or dust that has  
accumulated on the projector and on or in the filter.  
ꢁꢀ Do not put any flammable objects or spray cans near  
the projector, hot air is exhausted from the air vents.  
ꢁꢀ Keep the exhaust vent at least 3 feet (1 m) away from  
any objects.  
When the “Please clean filter” message is displayed, stop  
using the projector immediately and clean or replace the  
filter.  
ꢁꢀ Do not touch peripheral parts in the exhaust vents,  
especially screws and metallic parts. These areas will  
become hot while the projector is used.  
ꢁꢀ Do not put anything on the cabinet. Objects put on  
the cabinet will not only get damaged but may also  
cause a fire hazard.  
Cooling fans are provided to cool down the projector. The  
fans’ running speed is changed according to the tem-  
perature inside the projector.  
Blocking the air vents and leaving the projector un-  
cleaned for a long time may not only damage the projec-  
tor and may require costly repairs but may also cause  
accidents or fire.  
For maintenance of the filter, refer to “Option” on page 83  
and “Replacing the Filters” on pages 97 – 98.  
Damages to the projector caused by using an  
un-cleaned filter or improper maintenance will void  
the warranty on the projector.  
Installing the Projector in Proper Position  
Install the projector properly. Improper installation may reduce the lamp lifetime and cause a fire hazard.  
Do not tilt the projector  
more than 10 degrees  
above and below.  
Do not put the projector  
on either side to project  
an image.  
Do not point the projector  
up to project an image.  
NO UPWARD  
NO SIDEWAYS  
Do not point the projector  
down to project an image.  
NO DOWNWARD  
xi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compliance  
Federal Communications Commission Notice  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-  
lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tele-  
vision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
ꢁꢀ Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.  
ꢁꢀ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
ꢁꢀ Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes  
or modifications should be made, you could be required to stop operation of the equipment.  
Model Number(s)  
Trade Name  
: PDG-DXT10L  
: Sanyo  
Responsible party  
Address  
Telephone No.  
: SANYO FISHER COMPANY  
: 21605 Plummer Street, Chatsworth, California 91311 U.S.A.  
: (818)998-7322  
AC Power Cord Requirement  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada:  
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories  
(UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the  
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to  
insert the plug into the outlet, contact your electrician.  
AC Power Cord for the United Kingdom:  
This cord is already fitted with a modulized plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should  
the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus  
. If the fuse cover is  
detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same color as that visi-  
ble on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User  
Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord  
should be suitably prepared and the correct plug fitted.  
WARNING: A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.  
The Wires in this mains lead are colored in accordance with the following code:  
Green-and-yellow ············ Earth  
Blue ································· Neutral  
Brown ······························ Live  
As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in  
your plug proceed as follows:  
The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety  
earth symbol  
or colored green or green-and-yellow.  
The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black. The wire which is  
colored brown must be connected to the terminal which is marked with the letter L or colored red.  
WARNING: THIS APPARATUS MUST BE EARTHED.  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
1. INTRODUCTION ..................................................................................................................................................................................1  
n WHAT’S IN THE BOX?..........................................................................................................................................................................1  
o INTRODUCTION TO THE PROJECTOR...................................................................................................................................................2  
Features you’ll enjoy:........................................................................................................................................................................2  
p PART NAMES OF THE PROJECTOR .....................................................................................................................................................3  
Front-right View.................................................................................................................................................................................3  
Top view .............................................................................................................................................................................................4  
Carrying the Projector ......................................................................................................................................................................5  
Bottom view .......................................................................................................................................................................................6  
q TOP FEATURES ...................................................................................................................................................................................7  
Lens Controls.....................................................................................................................................................................................7  
OSD Controls and Status LEDs......................................................................................................................................................8  
r TERMINAL PANEL FEATURES............................................................................................................................................................10  
s PART NAMES OF THE REMOTE CONTROL ........................................................................................................................................12  
Battery Installation ..........................................................................................................................................................................14  
Operating Range for Wireless Remote Control..........................................................................................................................15  
Remote Control Precautions .........................................................................................................................................................15  
Remote Control Codes...................................................................................................................................................................15  
Using the Remote Control in Wired Operation ...........................................................................................................................16  
2. INSTALLATION AND CONNECTIONS .........................................................................................................................................17  
n SETTING UP THE SCREEN AND THE PROJECTOR.............................................................................................................................17  
o SELECTING A LOCATION....................................................................................................................................................................18  
p INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................................19  
Removing the Existing Lens From the Projector........................................................................................................................19  
Installing the New Lens..................................................................................................................................................................20  
Installing the New Lens Using the anti-theft screw....................................................................................................................21  
q THROW DISTANCE AND SCREEN SIZE..............................................................................................................................................22  
r INSTALLING THE OPTIONAL COLOR WHEEL .....................................................................................................................................24  
s MAKING CONNECTIONS.....................................................................................................................................................................26  
Connecting Your PC or Macintosh Computer.............................................................................................................................26  
Connecting an External Monitor....................................................................................................................................................28  
Connecting Your DVD Player with Component Output.............................................................................................................29  
Connecting Your VCR or Laser Disc Player ...............................................................................................................................30  
t CONNECTING THE SUPPLIED POWER CABLE ...................................................................................................................................31  
NOTE ON THE POWER CORD...................................................................................................................................................31  
3. PROJECTING AN IMAGE (BASIC OPERATION).......................................................................................................................32  
n TURNING ON THE PROJECTOR..........................................................................................................................................................32  
Note on Startup Screen (Menu Language Select screen)........................................................................................................33  
o SELECTING AN INPUT SOURCE .........................................................................................................................................................34  
p ADJUSTING THE PICTURE POSITION AND PICTURE SIZE..................................................................................................................35  
Adjusting Picture Position Manually.............................................................................................................................................35  
Lens Shift Adjustable Range.........................................................................................................................................................36  
From the Remote Control Unit ......................................................................................................................................................37  
Adjusting the Projector Level.........................................................................................................................................................38  
q OPTIMIZING AN RGB IMAGE AUTOMATICALLY .................................................................................................................................39  
Adjusting the Image Using AUTO PC ADJ. ................................................................................................................................39  
r ADJUSTING VOLUME UP AND DOWN ................................................................................................................................................40  
s TURNING OFF THE PROJECTOR ........................................................................................................................................................41  
About Direct Power Off...................................................................................................................................................................42  
After Use...........................................................................................................................................................................................42  
viii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
4. CONVENIENT FEATURES..............................................................................................................................................................43  
n TURNING OFF THE IMAGE AND SOUND.............................................................................................................................................43  
o FREEZING A PICTURE........................................................................................................................................................................43  
p ADJUSTING THE FOCUS/ZOOM MANUALLY.......................................................................................................................................44  
Adjusting by Using the OSD Control Panel.................................................................................................................................44  
q CHANGING LAMP MODE....................................................................................................................................................................45  
Changing Lamp Mode by Using the Projector's OSD Control Panel ......................................................................................45  
Changing Lamp Mode by Using the Remote Control................................................................................................................46  
r GETTING INFORMATION.....................................................................................................................................................................47  
s ADJUSTING POSITION/TOTAL DOTS/FINE SYNC ..............................................................................................................................48  
Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel ............................................................................48  
Correcting Keystone by Using the Remote Control...................................................................................................................49  
t PREVENTING THE UNAUTHORIZED USE OF THE PROJECTOR ..........................................................................................................51  
Locking the Projector......................................................................................................................................................................51  
Unlocking the Projector..................................................................................................................................................................53  
u USING THE PHYSICAL LOCK..............................................................................................................................................................54  
Using the Kensington Lock............................................................................................................................................................54  
Using the Security Chain Lock......................................................................................................................................................54  
5. USING ON-SCREEN DISPLAY.......................................................................................................................................................55  
n USING THE MENUS............................................................................................................................................................................55  
Navigating the OSD........................................................................................................................................................................55  
o MENU TREE.......................................................................................................................................................................................57  
p MENU ELEMENTS ..............................................................................................................................................................................59  
q SOURCE MENU DESCRIPTIONS AND FUNCTIONS.............................................................................................................................60  
r ADJUST MENU DESCRIPTIONS AND FUNCTIONS ..............................................................................................................................61  
Image menu.....................................................................................................................................................................................61  
Image options menu.......................................................................................................................................................................62  
Video menu......................................................................................................................................................................................64  
s DETAIL SETTINGS MENU DESCRIPTIONS AND FUNCTIONS ..............................................................................................................67  
Basic .................................................................................................................................................................................................67  
White balance..................................................................................................................................................................................69  
Color correction...............................................................................................................................................................................70  
t SETTING MENU DESCRIPTIONS AND FUNCTIONS.............................................................................................................................71  
Basic .................................................................................................................................................................................................71  
Installation........................................................................................................................................................................................75  
Network setting................................................................................................................................................................................82  
Option ...............................................................................................................................................................................................83  
u INFORMATION MENU DESCRIPTIONS AND FUNCTIONS.....................................................................................................................89  
Usage time.......................................................................................................................................................................................89  
Input ..................................................................................................................................................................................................90  
Network.............................................................................................................................................................................................91  
Version..............................................................................................................................................................................................92  
v RESET MENU DESCRIPTIONS AND FUNCTIONS................................................................................................................................93  
6. MAINTENANCE .................................................................................................................................................................................94  
n CLEANING THE PROJECTOR ..............................................................................................................................................................94  
Cleaning the Cabinet......................................................................................................................................................................94  
Cleaning the Lens...........................................................................................................................................................................94  
Cleaning the Filters.........................................................................................................................................................................95  
o REPLACING CONSUMABLE PARTS ....................................................................................................................................................97  
Replacing the Filters.......................................................................................................................................................................97  
Replacing the Lamps......................................................................................................................................................................99  
Resetting the Lamp Time Counter..............................................................................................................................................101  
Ordering a Replacement Lamp...................................................................................................................................................101  
x
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
7. APPENDIX ........................................................................................................................................................................................102  
n TROUBLESHOOTING ........................................................................................................................................................................102  
Indicator Messages.......................................................................................................................................................................102  
Common Problems and Solutions..............................................................................................................................................104  
Tips for Troubleshooting ..............................................................................................................................................................104  
o IMAGE PROBLEMS ...........................................................................................................................................................................105  
Lamp Problems .............................................................................................................................................................................105  
Remote Control Problems ...........................................................................................................................................................106  
Audio Problems.............................................................................................................................................................................106  
p HAVING THE PROJECTOR SERVICED..............................................................................................................................................106  
8. SPECIFICATIONS ...........................................................................................................................................................................107  
n PROJECTOR SPECIFICATIONS.........................................................................................................................................................107  
Optical Specifications...................................................................................................................................................................107  
Electrical Specifications ...............................................................................................................................................................108  
Mechanical Specifications ...........................................................................................................................................................109  
Environmental Considerations....................................................................................................................................................109  
Regulations....................................................................................................................................................................................109  
Optional Parts................................................................................................................................................................................110  
o CABINET DIMENSIONS.....................................................................................................................................................................111  
p PIN ASSIGNMENTS OF MINI D-SUB 15 PIN INPUT CONNECTOR....................................................................................................112  
q COMPATIBLE INPUT SIGNAL LIST....................................................................................................................................................113  
r PC CONTROL CODES AND CABLE CONNECTIONS.........................................................................................................................115  
Functional Execution Command Table......................................................................................................................................115  
Status Read Command Table.....................................................................................................................................................116  
s SCREEN TRIGGER...........................................................................................................................................................................117  
t OPERATION USING HTTP BROWSER.............................................................................................................................................118  
Overview.........................................................................................................................................................................................118  
Preparation Before Use................................................................................................................................................................118  
Handling of the Address for Operation by Using a Browser...................................................................................................118  
Configuring Network Settings......................................................................................................................................................119  
Structure of the HTTP Server......................................................................................................................................................121  
u 15 PIN GPIO CONTROL .................................................................................................................................................................123  
9. TROUBLESHOOTING CHECK LIST ...........................................................................................................................................124  
xi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
n What’s in the Box?  
Carefully unpack the projector and check that the following items are included:  
PDG-DXT10L Projector  
Remote Control  
(with Two AA alkaline batteries)  
Power Cable  
(3.6m/11.8 ft.)  
ĺ For North  
America,  
Europe and  
the UK  
Quick Start Guide  
Remote Cable  
(10m/33ft)  
VGA Cable  
ƒꢀAnti-Theft  
Screw for lens  
x 1  
ƒꢀSecurity  
Sticker  
CD-ROM  
(This User’s manual)  
Lens Hole Cap  
(Installed)  
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.  
CAUTION  
Avoid using the projector in dusty environments.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
o Introduction to the Projector  
Features you’ll enjoy:  
DLP projector with high resolution  
The combination of BrilliantColor™ and a six-segment color wheel (optional) offer a more true color reproduction.  
Installation Flexibility  
This projector has many useful functions such as powered lens shifting, ceiling and rear projection, variety of extensive op-  
tional powered lens with bayonet mount with release button, etc.  
Multiple Interface Terminals  
The projector has several interface terminals that can support various types of equipment and signals.  
Dual Lamp Control System  
The two-lamp control system offers high brightness, maintained lamp life and energy savings along with redundancy. The  
lamp control function offers brightness of the lamp can be selected. The power management function also reduces power  
consumption and maintains lamp life.  
Simple Computer System Setting  
The projector has the Multi-scan system to conform to almost all computer output signals quickly. Up to UXGA resolution  
can be accepted.  
Security Function  
The Security function helps you to ensure security of the projector. With the Key lock function, you can lock the operation on  
the top control. PIN code lock functions prevent unauthorized use of the projector.  
Multilanguage Menu Display  
Operation menu is available in 8 languages: English, German, French, Italian, Spanish, Swedish, Chinese, and Japanese.  
Multi-use Remote Control  
Use the remote control as wired or wireless. Eight remote control codes are available.  
3W + 3W Stereo Speaker  
Built in 3W x 2 speakers are provided.  
Helpful Maintenance Functions  
The lamp and filter maintenance functions provide for better and proper maintenance of the projector. Easy maintenance  
cover is provided for lamp and color wheel replacement.  
Network-capable  
Through an optional Network Manager with serial port in, you can operate and control the projector.  
Direct Power Off and On Start  
The Direct Power Off function allows the projector to be turned off (even when projecting an image) using a power strip  
equipped with a switch and a breaker. The On Start function allows the projector to be turned on by supplied AC power.  
Note:  
Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector  
and starting to display an image. Also, the power cord can be removed immediately after turning off the pro-  
jector. On Start manual may differ slightly from the product.  
On Start eliminates the need to always use the POWER (ON/STANDBY) button on the remote control or  
projector cabinet.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
p Part Names of the Projector  
Front-right view  
ITEM  
LABEL  
IR receiver  
DESCRIPTION  
SEE PAGE:  
Receiver for IR signal from remote control  
Remove cover to replace lamp or color wheel  
1.  
2.  
12  
99  
Lamp cover  
Lens control panel  
See Lens Controls  
3.  
4.  
7
8
OSD control panel  
See OSD Controls and Status LEDS  
I/O connector panel  
Intake vent  
Speakers  
Connect various input devices  
Lamp cooling vent – do not obstruct  
Built-in stereo speakers  
5.  
6.  
7.  
8.  
9.  
10  
—
—
6
Height adjuster  
Lens  
Adjusts level of projector  
Remove lens cap before use  
—
Lens release button  
Anti-Theft screw  
Press the release button before removing the lens  
Prevent theft of the lens  
10.  
11.  
—
—
Keeps the front fan free of dust  
– clean regularly for optimum performance  
– do not obstruct  
Intake vent and front  
filter  
12.  
95  
Important:  
Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the grill  
openings.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Top view  
ITEM  
LABEL  
DESCRIPTION  
SEE PAGE:  
Lens control panel  
Right-hand speaker  
Lamp cover  
See Lens Controls  
Right-hand speaker  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
7
—
Remove cover to replace lamp or color wheel  
Exhaust vent – do not obstruct  
99  
—
Exhaust vent  
OSD control panel  
Rear intake vent  
Left intake vent  
Left-hand speaker  
See OSD Controls and Status LEDS  
Rear cooling intake – do not obstruct  
Left-hand cooling intake – do not obstruct  
Left-hand speaker  
8
—
—
—
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Carrying the Projector  
Always carry your projector by the handle.  
Before moving or carrying the projector, disconnect the power cable and any other cables that may be attached to it.  
When moving the projector or when the projector is not in use, cover the lens with the lens cap.  
To extend the projector handle, refer to the following guide.  
1. Stand the projector on its end with the control panels at the bottom.  
2. Lift the handle in the direction shown until it is fully extended.  
Note:  
Stand the projector on its end by lifting the cabinet. Do not use the handle to place the projector upright.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Bottom view  
ITEM  
1.  
LABEL  
DESCRIPTION  
SEE PAGES:  
Height adjusters  
Intake vent  
Adjust projection height  
38  
—
Color wheel cooling vent – do not obstruct  
2.  
Keep the fan free of dust – clean regularly for optimum perform-  
ance  
Front filter  
3.  
4.  
5.  
95  
Contact your dealer for information on mounting the projector on  
a ceiling  
—
Ceiling support holes  
Security chain  
opening  
Attach anti-theft device – see u Using the Physical Lock  
54  
95  
Rear filter  
Side filter  
6.  
7.  
Keep the fans free of dust – clean regularly for optimum per-  
formance  
With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 12 mm; dis-  
tance from ceiling/ wall: 20 cm (0.7 feet) for proper ventilation; distance from fluorescent lamps: at least 1 m (3  
feet) front and back of the projector. For permanent installations, follow local codes.  
CAUTION  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
q Top Features  
Lens Controls  
ITEM  
1.  
LABEL  
DESCRIPTION  
SEE PAGE:  
ZOOM  
Increase/decrease projected image size  
44  
UP CURSOR  
RIGHT CURSOR  
DOWN CURSOR  
LEFT CURSOR  
FOCUS  
2.  
3.  
Move image left, right, up, or down  
Focus the projected image  
4.  
5.  
6.  
44  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
OSD Controls and Status LEDs  
ITEM  
LABEL  
MENU  
DESCRIPTION  
SEE PAGE:  
Open / Close the OSD  
1.  
55  
UP/ DOWN/ LEFT/  
RIGHT BUTTONS  
Navigate and change settings in the OSD  
Increase volume  
2.  
3.  
55  
40  
RIGHT CURSOR/  
VOLUME  
INCREASE  
CANCEL  
INPUT  
Exit the On-Screen Display (OSD)  
Change or select the input device  
4.  
5.  
55  
34  
Turn the projector on or off (main power switch must be turned  
on first).  
Press to place the projector in standby mode.  
ON/STAND-BY  
LAMP 2 (LED)  
6.  
7.  
39  
Green  
See Indicator Messages  
102  
Flashing  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
ITEM  
LABEL  
DESCRIPTION  
SEE PAGE:  
Green  
Flashing  
Green  
Red  
LAMP 1 (LED)  
See Indicator Messages  
8.  
102  
102  
WARNING (LED)  
See Indicator Messages  
See Indicator Messages  
9.  
Orange  
Flashing  
Green  
POWER (LED)  
AUTO PC ADJ.  
10.  
Orange  
Flashing  
102  
Optimize image size, position, and resolution  
Select or change settings in the OSD  
11.  
12.  
13.  
10  
55  
40  
SELECT  
LEFT  
CURSOR/VOLUME Decrease volume  
DECREASE  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
r Terminal Panel Features  
ITEM  
LABEL  
DESCRIPTION  
SEE PAGE:  
COMPUTER 3 IN  
Connect the DVI-D cable (not supplied) from a computer  
1.  
26  
AUDIO IN  
(COMPUTER 3)  
—
Connect the audio cable (not supplied) from the input device  
2.  
—
—
AUDIO OUT  
Audio loop-thru  
3.  
4.  
MONITOR OUT  
Connect to a monitor  
R/C JACK  
Connect the remote to the projector  
5.  
6.  
15  
AUDIO IN  
(COMPUTER 2)  
—
Connect the audio cable (not supplied) from the input device  
AUDIO IN  
[L(MONO)/R]  
(COMPONENT)  
Connect an RCA audio cables (not supplied) from the input de-  
vice right and left channels  
—
7.  
SERIAL PORT IN  
REMOTE IN  
Installation control  
For external control  
8.  
9.  
117  
117  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
ITEM  
LABEL  
SCREEN  
DESCRIPTION  
SEE PAGE:  
When connected to the screen through a commercially available  
cable, the screen deploys automatically on start up of the projec-  
tor. The screen retracts when the projector is powered off  
(see notes below)  
10.  
117  
TRIGGER  
Connect a commercially available S-video cable from a video  
device  
S-VIDEO  
11.  
29  
POWER SWITCH  
AC IN  
Turn on/off the projector  
12.  
13.  
41  
31  
Connect the supplied power cable  
AUDIO IN  
[L(MONO)/R]  
(VIDEO)  
Connect RCA audio cables (not supplied) from the input device  
right and left channels. This audio jack is shared with S-Video  
input.  
—
14.  
Connect a composite video cable (not supplied) from a video de-  
vice to the yellow RCA jack  
VIDEO IN  
15.  
16.  
30  
30  
COMPONENT IN  
(Y, Cb/Pb, Cr/Pr)  
Connect a component video enabled device  
COMPUTER 2 IN  
(R/Cr, G/Y, B/Cb,  
H, V)  
Connect RGBHV or Component signal from computer or com-  
ponent video enabled device  
17.  
30  
COMPUTER 1 IN  
Connect a VGA cable (supplied) from a computer  
Connect the audio cable (not supplied) from the input device  
Connect a LAN cable (not supplied) from a computer  
18.  
19.  
20.  
21.  
26  
AUDIO IN  
(COMPUTER 1)  
—
LAN  
26  
Connect the USB cable (not supplied) from a computer. For ser-  
vice personnel only.  
—
SERVICE  
Note:  
y To use this feature, you must turn on the Screen Trigger function on the OSD.  
y Screen controllers are supplied and supported by screen manufacturers.  
y Do not use this jack for anything other than intended use. Connecting the wired remote control to the  
Trigger mini jack causes damage to the remote control.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
s Part Names of the Remote Control  
ITEM  
LABEL  
LABEL  
NO SHOW  
Temporarily turns off screen  
image.  
ITEM  
15.  
1.  
ON  
D. ZOOM -/+  
Zoom in/out function.  
2.  
3.  
STAND-BY  
16.  
17.  
AUTO PC  
Automatically adjust the  
computer image.  
LIGHT  
Illuminate the remote panel.  
MENU  
Open or close the on-Screen  
menu.  
KEYSTONE  
Correct keystone distortion.  
4.  
18.  
5.  
6.  
CANCEL  
VOLUME -/+  
COMPUTER 1  
19.  
20.  
VOLUME -  
SELECT  
Executes a selected menu  
item  
7.  
8.  
9.  
COMPUTER 2  
21.  
22.  
23.  
VOLUME +  
LENS SHIFT  
Shift the lens up, down, right  
and left.  
COMPUTER 3  
COMPONENT  
Select the component input  
source.  
S-VIDEO  
Select the S-video input  
source.  
FOCUS/ZOOM  
Correct image distortion.  
10.  
11.  
24.  
25.  
VIDEO  
Select the video input  
source.  
IMAGE  
Select image mode  
SCREEN  
Select the screen size.  
12.  
13.  
IR TRANSMITTER  
26.  
27.  
FREEZE  
Freeze the picture.  
IR TRANSMITTER  
REMOTE JACK  
Connect a wired remote con-  
trol.  
LAMP CONTROL  
Select a lamp mode.  
14.  
28.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Important:  
Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights  
can disrupt remote control operation.  
1. Be sure nothing obstructs the path between the remote control and the projector. If the path between re-  
mote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as  
projector screens.  
2. The buttons and keys on the projector have the same functions as the corresponding buttons on the re-  
mote control. This user’s manual describes the functions based on the remote control.  
Note:  
* To turn off the projector, press the STAND-BY button twice.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Battery Installation  
The Remote Control unit included with the projector does not contain batteries, though batteries are supplied as part of the  
complete package. To insert (or replace) the batteries, refer to the following guide.  
Remove the battery compartment cover  
1.  
by squeezing the locking catch and slid-  
ing the cover in the direction of the  
arrow.  
Insert the supplied batteries taking note  
of the polarity (+/-) as shown.  
2.  
Replace the cover locator, and then  
click locking catch into place as shown.  
3.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Operating Range for Wireless Remote Control  
Point the remote control toward the projector (to Infrared Remote Re-  
ceivers) when pressing the buttons. Maximum operating range for the  
remote control is about 16.4 feet (5 m) and 60 degrees in front and rear  
of the projector.  
Infrared remote receivers are provided both in front and back of the pro-  
jector. You can conveniently use both of the receivers.  
Remote Control Precautions  
The following precautions ensure that the remote operates correctly and  
safely.  
xꢀ Use two (2) AA or LR6 type alkaline batteries.  
xꢀ Always replace batteries in sets.  
xꢀ Do not use a new battery with a used one.  
xꢀ Avoid contact with water or liquid.  
xꢀ Do not expose the remote control to moisture or heat.  
xꢀ Do not drop the remote control.  
xꢀ If the battery has leaked on the remote control, carefully wipe the  
case clean and install new batteries.  
xꢀ Risk of an explosion if battery is replaced by an incorrect type.  
xꢀ Dispose of used batteries according to the instructions.  
Remote Control Codes  
This projector provides eight different remote control codes (Code 1–Code 8); the factory-set, initial code (Code 1) and the  
other seven codes (Code 2 to Code 8). This switching function prevents remote control interference when operating sev-  
eral projectors or video equipment at the same time.  
The same code should be set on both the projector and the remote control.  
For example operating the projector in “Code 7”, both the projector and the remote control must be switched to “Code 7”.  
To change the code for the projector;  
Select a remote control code in the Menu.  
To change the code for the remote control;  
Check the Reset Switch to Use position in the compartment lid on back of the remote control.  
With holding down the MENU button, press the IMAGE button. By pressing the IMAGE button, the code switches in a se-  
quential order.  
To reset the code for the remote control;  
Slide the Reset Switch to "Reset position" in the compartment lid on back of the remote control.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Introduction  
Using the Remote Control in Wired Operation  
Connect the supplied remote cable to the R/C jack on the projector (see r Terminal Panel Features on page 10) and the  
other end to the remote jack on the remote control (see item 1, s Part Names of the Remote Control on page 12).  
Note:  
Connecting the remote cable to the R/C jack on the terminal panel will make the wireless operation unavail-  
able.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
n Setting Up the Screen and the Projector  
This section briefly describes how to set up your projector and how to connect video and  
audio sources.  
Your projector is simple to set up and use. But before you get started, you must first:  
xꢀ Set up a screen and the projector.  
xꢀ Connect your computer or video equipment to the projector. See s Making Connections on page 26.  
xꢀ Connect the supplied power cable. See t Connecting the Supplied Power Cable on page 31.  
Note:  
Ensure that the power cable and any other cables are disconnected before moving the projector. When  
moving the projector or when it is not in use, cover the lens with the lens cap.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
o Selecting a Location  
Locating the projector correctly ensures optimum performance and a longer parts life.  
Take note of the following when setting up the projector:  
xꢀ The projector table or stand should be level and sturdy.  
xꢀ Position the projector so that it is perpendicular to the screen.  
xꢀ Ensure cables do not cause a trip hazard.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
p Installing or Removing the Optional Lens  
xꢀ Do not shake or place excessive pressure on the projector or the lens components as the projector and  
lens components contain precision parts.  
xꢀ When shipping the projector with the optional lens, remove the optional lens before shipping the projec-  
tor. The lens and the lens shift mechanism may encounter damage caused by improper handling during  
transportation.  
CAUTION  
xꢀ Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans stop,  
and turn off the main power switch.  
xꢀ Do not touch the lens surface when removing or installing the lens.  
xꢀ Keep fingerprints, dust or oil off the lens surface. Do not scratch the lens surface.  
xꢀ Work on a level surface with a soft cloth under it to avoid scratching.  
xꢀ If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.  
Removing the Existing Lens From the Projector  
Pull out the lens cap.  
1.  
Push the LENS RELEASE button all the way  
in and rotate the lens counterclockwise.  
The existing lens will be disengaged.  
2.  
Note:  
If the lens cannot be removed even by  
using the LENS RELEASE button, the  
anti-theft screw for lens may be in use  
to secure the lens. If that is the case,  
remove the anti-theft screw first.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Pull out the existing lens slowly.  
3.  
CAUTION  
When Installing the lens into the projector, be sure to remove the lens cap from the back of the optional  
lens before installing the optional lens into the projector. Failure to do so will cause damage to the projec-  
tor.  
Installing the New Lens  
Insert the lens label side up.  
1.  
Rotate the lens clockwise until it  
clicks into place.  
2.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Installing the New Lens Using the anti-theft screw  
Using the anti-theft screw to prevent theft of  
the lens.  
Tighten the supplied anti-theft screw on the  
front bottom.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
q Throw Distance and Screen Size  
Example of LNS-S40:  
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approxi-  
mately 40 inches (1 m) measured diagonally when the projector is roughly 65 inches (1.7 m) from the wall or screen. The  
largest the image can be is 500 inches (12.7 m) when the projector is about 843 inches (21.4 m) from the wall or screen.  
Screen Size  
Width  
LNS-W41  
0.77  
LNS-W40  
1.33 - 1.79  
LNS-S40  
1.78 - 2.35  
Diagonal  
Height  
Distance  
[m]  
[inches] [m] [inches] [m] [inches] [m] [inches] [m]  
[inches]  
[inches]  
[m]  
40  
50  
1.02  
1.27  
1.52  
1.70  
1.83  
2.03  
2.13  
2.29  
2.54  
3.05  
3.81  
4.57  
5.08  
5.33  
6.10  
6.63  
6.86  
7.62  
8.89  
10.16  
11.43  
12.70  
32  
40  
0.81  
1.02  
1.22  
1.36  
1.46  
1.63  
1.71  
1.83  
2.03  
2.44  
3.05  
3.66  
4.06  
4.27  
4.88  
5.30  
5.49  
6.10  
7.11  
8.13  
9.14  
10.16  
24  
30  
0.61  
0.76  
0.91  
1.02  
1.10  
1.22  
1.28  
1.37  
1.52  
1.83  
2.29  
2.74  
3.05  
3.20  
3.66  
3.98  
4.11  
4.57  
5.33  
6.10  
6.86  
7.62  
41.7 - 56.8 1.06 - 1.44 55.8 - 74.4 1.42 - 1.89  
52.6 - 71.5 1.34 - 1.82 70.4 - 93.7 1.79 - 2.38  
63.5 - 86.1 1.61 - 2.19 85.0 - 112.9 2.16 - 2.87  
71.1 - 96.4 1.81 - 2.45 95.2 - 126.4 2.42 - 3.21  
76.6 - 103.7 1.94 - 2.63 102.5 - 136.0 2.60 - 3.45  
85.3 - 115.4 2.17 - 2.93 114.1 - 151.3 2.90 - 3.84  
89.6 - 121.3 2.28 - 3.08 120.0 - 159.0 3.05 - 4.04  
96.2 - 130.1 2.44 - 3.30 128.7 - 170.6 3.27 - 4.33  
30.7 0.78  
37.1 0.94  
41.6 1.06  
44.9 1.14  
50.0 1.27  
52.6 1.34  
56.5 1.44  
60  
48  
36  
67  
54  
40  
72  
58  
43  
80  
64  
48  
84  
67  
50  
90  
72  
54  
100  
120  
150  
180  
200  
210  
240  
261  
270  
300  
350  
400  
450  
500  
80  
60  
63.0 1.60 107.0 - 144.7 2.72 - 3.68 143.3 - 189.8 3.64 - 4.82  
75.9 1.93 128.8 - 174.0 3.27 - 4.42 172.5 - 228.2 4.38 - 5.80  
95.3 2.42 161.5 - 218.0 4.10 - 5.54 216.2 - 285.9 5.49 - 7.26  
114.6 2.91 194.1 - 261.9 4.93 - 6.65 260.0 - 343.6 6.60 - 8.73  
127.6 3.24 215.9 - 291.2 5.48 - 7.40 289.1 - 382.0 7.34 - 9.70  
226.8 - 305.9 5.76 - 7.77 303.7 - 401.3 7.71 - 10.19  
259.5 - 349.8 6.59 - 8.89 347.5 - 458.9 8.83 - 11.66  
282.3 - 380.6 7.17 - 9.67 378.1 - 499.3 9.60 - 12.68  
292.1 - 393.8 7.42 - 10.00 391.2 - 516.6 9.94 - 13.12  
324.8 - 437.7 8.25 - 11.12 435.0 - 574.3 11.05 - 14.59  
379.2 - 511.0 9.63 - 12.98 507.9 - 670.4 12.90 - 17.03  
433.7 - 584.3 11.02 - 14.84 580.8 - 766.5 14.75 - 19.47  
488.1 - 657.5 12.40 - 16.70 653.7 - 862.6 16.60 - 21.91  
542.6 - 730.8 13.78 - 18.56 726.6 - 958.7 18.46 - 24.35  
96  
72  
120  
144  
160  
168  
192  
209  
216  
240  
280  
320  
360  
400  
90  
108  
120  
126  
144  
157  
162  
180  
210  
240  
270  
300  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Screen Size  
Width  
LNS-T40  
LNS-T41  
4.43 - 8.3  
2.22 - 4.43  
Diagonal  
Height  
Distance  
[inches]  
[inches] [m] [inches] [m] [inches] [m]  
[inches]  
[m]  
[m]  
40  
50  
1.02  
1.27  
1.52  
1.70  
1.83  
2.03  
2.13  
2.29  
2.54  
3.05  
3.81  
4.57  
5.08  
5.33  
6.10  
6.63  
6.86  
7.62  
8.89  
10.16  
11.43  
12.70  
32  
40  
0.81  
1.02  
1.22  
1.36  
1.46  
1.63  
1.71  
1.83  
2.03  
2.44  
3.05  
3.66  
4.06  
4.27  
4.88  
5.30  
5.49  
6.10  
7.11  
8.13  
9.14  
10.16  
24  
30  
0.61  
0.76  
69.4 - 142.3 1.76 - 3.61 139.2 - 266.9 3.54 - 6.78  
87.8 - 178.9 2.23 - 4.54 175.3 - 335.0 4.45 - 8.51  
60  
48  
36  
0.91 106.2 - 215.5 2.70 - 5.47 211.5 - 403.1 5.37 - 10.24  
1.02 119.0 - 241.2 3.02 - 6.13 236.8 - 450.8 6.01 - 11.45  
1.10 128.2 - 259.5 3.26 - 6.59 254.8 - 484.9 6.47 - 12.32  
1.22 142.9 - 288.8 3.63 - 7.34 283.7 - 539.4 7.21 - 13.70  
1.28 150.3 - 303.5 3.82 - 7.71 298.2 - 566.6 7.57 - 14.39  
1.37 161.3 - 325.4 4.10 - 8.27 319.9 - 607.5 8.12 - 15.43  
1.52 179.7 - 362.1 4.56 - 9.20 356.0 - 675.6 9.04 - 17.16  
1.83 216.4 - 435.3 5.50 - 11.06 428.3 - 811.8 10.88 - 20.62  
2.29 271.6 - 545.2 6.90 - 13.85 536.6 - 1016.1 13.63 - 25.81  
2.74 326.7 - 655.1 8.30 - 16.64 645.0 - 1220.5 16.38 - 31.00  
3.05 363.5 - 728.3 9.23 - 18.50 717.3 - 1356.7 18.22 - 34.46  
3.20 381.9 - 765.0 9.70 - 19.43 753.4 - 1424.8 19.14 - 36.19  
3.66 437.0 - 874.9 11.10 - 22.22 861.8 - 1629.1 21.89 - 41.38  
3.98 475.6 - 951.8 12.08 - 24.18 937.7 - 1772.2 23.82 - 45.01  
4.11 492.2 - 984.7 12.50 - 25.01 970.2 - 1833.5 24.64 - 46.57  
67  
54  
40  
72  
58  
43  
80  
64  
48  
84  
67  
50  
90  
72  
54  
100  
120  
150  
180  
200  
210  
240  
261  
270  
300  
350  
400  
450  
500  
80  
60  
96  
72  
120  
144  
160  
168  
192  
209  
216  
240  
280  
320  
360  
400  
90  
108  
120  
126  
144  
157  
162  
180  
210  
240  
270  
300  
4.57 547.3 - 1094.6 13.90 - 27.80 1078.6  
5.33 639.2 - 1277.8 16.24 - 32.46 1259.2  
6.10 731.1 - 1460.9 18.57 - 37.11 1439.9  
6.86 823.0 - 1644.0 20.90 - 41.76 1620.5  
7.62 914.9 - 1827.2 23.24 - 46.41 1801.2  
-
-
-
-
-
2037.8 27.40 - 51.76  
2378.3 31.98 - 60.41  
2718.9 36.57 - 69.06  
3059.4 41.16 - 77.71  
3400.0 45.75 - 86.36  
Ceiling installation must be done by a qualified professional. Contact your SANYO dealer for more  
information.  
It is not recommended you install the projector yourself.  
Only use the projector on a solid, level surface. Serious injury and damage can occur if the projector  
is dropped.  
CAUTION  
Do not use the projector in an environment where extreme temperature occurs. The projector must  
be used at temperatures between 41 degrees Fahrenheit (5 degrees Celsius) and 104 degrees Fahr-  
enheit (40 degrees Celsius).  
Screen damage will occur if the projector is exposed to moisture, dust or smoke.  
Do not cover the vents on the projector. Proper ventilation is required to dissipate heat. Damage to  
the projector will occur if the vents are covered.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
r Installing the Optional Color Wheel  
The PDG-DXT10L projector comes with a four-segment color wheel installed. An additional six-segment color wheel is op-  
tional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the following guide.  
Note:  
Wait until the lamp house and the color wheel cool off.  
Loosen the captive screw (A)  
on the lamp cover.  
1.  
Remove the lamp cover by  
sliding it in the direction of  
the arrow (B).  
2.  
Unscrew the retaining screws  
(x 4) on the four-segment  
color wheel.  
3.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Lift the color wheel in the  
direction shown.  
4.  
5.  
6.  
Insert the six-segment color  
wheel  
Secure the retaining screws as  
shown.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Align the lamp cover (A) with  
the arrow mark on the cabinet  
and slide it into place.  
7.  
Secure the captive screw (B).  
8.  
Storing Unused Color Wheel:  
Keep the unused color wheel in the zipper bag in which the 6-segment color wheel (not supplied) was packaged.  
This bag prevents dust from falling or collecting on the color wheel.  
s Making Connections  
Connecting Your PC or Macintosh Computer  
Enabling the computer’s external display  
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector. When  
using a PC compatible laptop, a combination of function keys will enable/disable the external display. Usually, the combi-  
nation of the Fn-key along with one of the 12 function keys activates the external display.  
To connect a PC or Macintosh computer to the projector, refer to the following guide.  
1. Connect a computer to the projector through one of the three available input data connections before turning  
on the PC or the projector. The best signal order (from best to least suitable) is as follows:  
ƒꢀ Computer 3 in (see item 1, r Terminal Panel Features on page 10) is a digital signal and offers the best  
connection to your computer.  
Note:  
The DVI (DIGITAL) connector (COMPUTER 3) accepts VGA (640 x 480), 1152 x 864,  
XGA (1024 x 768), SXGA (1280 x 1024@up to 60Hz) and SXGA+(1400 x 1050 @ up to 60Hz).  
ƒꢀ Computer 2 in (see item 17, r Terminal Panel Features on page 10) is an analog signal; use a DSUB-15  
cable-to-5BNC connection.  
ƒꢀ Computer 1 in as shown below (see item 18, r Terminal Panel Features on page 10) is an analog signal  
that uses a standard RGB computer cable.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
2. Turn on the projector and select the chosen method of connection from the source menu before turning on the  
PC (see o Selecting an Input Source on page 34).  
3. Turn on the PC.  
Note:  
Failure to follow the above steps may not activate the digital output of the graphics card resulting in no pic-  
ture being displayed. Should this happen, restart your PC.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Connecting an External Monitor  
Connect an external monitor to the projector through RGB out connections as shown below  
(see item 4, r Terminal Panel Features on page 10)  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Connecting Your DVD Player with Component Output  
To connect a DVD Player to the projector, refer to the following guide.  
1. Connect the DVD Player to the projector as shown below before turning on the Player or the projector.  
2. Turn on the projector and select Component from the source menu before turning on the DVD Player  
(see o Selecting an Input Source on page 34).  
3. Turn on the DVD Player.  
Note:  
Refer to your DVD player's user's manual for more information about your DVD player's video output re-  
quirements.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
Connecting Your VCR or Laser Disc Player  
To connect your VCR or Laser Disc Player, refer to the following diagram.  
Note:  
Refer to your VCR or laser disc player user’s manual for more information about your device’s requirements.  
Images may not be displayed correctly when using an S-Video or Video connection to fast-forward or fast-  
rewind scanning.  
The AUDIO IN RCA jack is shared between VIDEO IN and S-VIDEO IN.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Installation and Connections  
t Connecting the Supplied Power Cable  
This projector uses nominal input voltages of 100–120V or 200–240V AC and it automatically selects the correct input volt-  
age. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of  
electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being supplied,  
consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the  
projector on.  
CAUTION  
For safety, unplug the AC power cord when the projector is not in use. When the projector is con-  
nected to an outlet with the AC power cord, it is in stand-by mode and consumes a small amount of  
electrical power.  
NOTE ON THE POWER CORD  
The AC power cord must meet the requirements of the country where you are utilizing the projector. Confirm the AC plug  
type with the chart below. The proper AC power cord must be used. If the supplied AC power cord does not match your AC  
outlet, contact your sales dealer.  
Note:  
Make sure that the prongs are fully inserted into both the AC IN and the wall outlet.  
CAUTION  
Ensure that the cables do not create a trip hazard.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
n Turning on the Projector  
Once the projector is correctly located and the power cable and other connections are in place, it is important that the pro-  
jector is powered on correctly in order to avoid damage to components and unnecessary wear and tear. Refer to the  
following guide to power on the projector.  
Connect the power cable (A). Press the  
main power switch to the on ( I ) posi-  
1.  
tion as shown (B). The power LED  
lights orange and warning LED lights  
green.  
B
A
Press the On/Standby button once (see  
2.  
OSD Controls and Status LEDS on  
page 8). The power LED lights green  
and the internal cooling fan starts.  
After approximately 10 seconds, the  
power LED flashes intermittently green.  
3.  
The Lamp1 and Lamp2 LEDs light  
green and the Power LED flashes more  
rapidly.  
4.  
Once the power LED is lit a solid green,  
the projector is ready for use.  
5.  
Note:  
If any of the LEDs remain flashing or blink there may be a problem with the startup. Please refer to the  
n Troubleshooting section on page 102.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
Note on Startup Screen (Menu Language Select screen)  
In the first instance of powering on the projector, the language menu is displayed to select the default language.  
Select the required default language using the Ÿ or ź buttons on the OSD menu panel or the remote control unit and  
press Select.  
Note:  
The language select screen only appears on the first instance of power on. All subsequent operations as-  
sume the selected default language. To change the default see page 74.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
o Selecting an Input Source  
The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following  
guide to select the Input Source.  
Press Menu on the OSD control panel or on the remote  
control unit to display the Main Menu. Scroll to the  
1.  
Input menu using Ÿorź and press Select.  
Note:  
Return to the projected image by pressing Cancel  
twice.  
Select the required source using Ÿorź and press  
Select.  
2.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
p Adjusting the Picture Position and Picture Size  
The Picture Position and Picture Size can be adjusted manually from the lens control panel or from the remote control unit.  
Refer to the following guides to adjust Picture Position manually.  
Adjusting Picture Position Manually  
Press the Select keypad in any direction to  
bring up the Lens Shift window.  
1.  
Press the directional key as required to  
2.  
shift the image. Releasing the  
directional arrow will  
re-center the cursor.  
To alter the picture size, press Menu and  
3.  
select the Adjust menu using Ÿorź. Press  
Select to open the Adjust menu. Press  
ŻorŹ to select Image Options followed  
by Ÿorź to select Screen. Press  
Select.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
The Screen window is displayed. Select  
the desired picture size using Ÿorź and  
press Select.  
4.  
When finished, press Cancel to return to  
the projected image.  
5.  
Lens Shift Adjustable Range  
The adjustable range for lens shift is tabulated below and subject to the conditions listed.  
Note:  
The drawings below apply to the standard lens (LNS-S40) only.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
From the Remote Control Unit  
Press the Lens Shift button to bring up the  
Lens Shift window.  
1.  
Press the directional keys as required to  
shift the image. Releasing the directional  
arrow will re-center the cursor.  
2.  
To alter the picture size, press the Screen  
button to display the Screen window.  
3.  
Select the desired picture size using Ÿorź  
and press Select.  
4.  
When finished, press Cancel to return to  
the projected image.  
5.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
Adjusting the Projector Level  
To raise the level of the projector, twist the adjust-  
ers clockwise.  
1.  
To lower the level of the projector, lift the projector  
and twist the adjusters counter clockwise.  
2.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
q Optimizing an RGB Image Automatically  
Adjusting the Image Using AUTO PC ADJ.  
To optimize an RGB image automatically refer to the following guide.  
Press the AUTO PC button on the remote control (see item 17, s Part Names of the Remote Control on page 12) or the  
AUTO PC ADJ. button on the OSD control panel to optimize an RGB image automatically.  
This adjustment may be necessary when you connect your computer for the first time.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
r Adjusting Volume Up and Down  
The volume can be adjusted from the OSD Control Panel or with the Remote Control unit. Refer to the following as a guide.  
Press the Volume +/- buttons on the remote  
1.  
control or the Ż Ź buttons on the OSD con-  
trol panel. The volume level is displayed on  
screen.  
Use the Volume +/- buttons or the Ż Ź but-  
tons on the OSD control panel to adjust the  
level.  
2.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
s Turning off the Projector  
Once the projector is no longer required, it is important to shut it down correctly to avoid damage or unnecessary wear and  
tear to the projector.  
xꢀ Do not unplug the power cable from the wall outlet or projector when the projector is powered on.  
Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the  
power cable. To turn off the AC power supply when the projector is powered on, use a power strip  
CAUTION  
equipped with a switch and a breaker.  
xꢀ Do not turn off the AC power supply within 10 seconds of making adjustment or setting changes  
and closing the menu. Doing so can cause loss of adjustments and settings and return to default.  
Refer to the following guide to shut down the projector.  
Press the On/Standby button once. The Power Off  
window displays.  
1.  
Press the On/Standby button or Select again on the  
OSD control panel or remote control to verify  
2.  
power off.  
The cooling fans continue to operate (cooling-off  
time).  
The cooling fans stop operating when the projector  
turns off.  
The projector enters Standby mode and the power  
LED lights orange.  
3.  
Press the Main Power switch to the off position (O)  
to turn off the projector.  
4.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Projecting an Image (Basic Operation)  
About Direct Power Off  
The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image)  
using a power strip equipped with a switch and a breaker.  
Note:  
Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector  
and starting to display an image.  
After Use  
Preparation: Make sure that the projector is turned off.  
1. Unplug the power cable.  
2. Disconnect any other cables.  
3. Return the height adjusters to their original, minimum position.  
4. Cover the lens with the lens cap.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
n Turning Off the Image and Sound  
The projected image and sound can be turned off for short periods of time with the remote control. This feature is useful for  
breaking up presentations or for other brief interruptions in projections. To turn off the picture and image, refer to the  
following guide.  
1. Press the NO SHOW button on the remote control once (see s Part Names of the Remote Control on page 12).  
2. The image does not display.  
3. To resume projection, press the NO SHOW button once more.  
Note:  
For extended periods of time it is recommended that the projector be powered off.  
o Freezing a Picture  
The projected image can be frozen for short periods of time by using the remote control. This feature is useful for capturing  
still images from movies or freezing an animation at a particular point. To freeze the projected image, refer to the following  
guide.  
1. Press the FREEZE button on the remote control once (see s Part Names of the Remote Control on page 12).  
2. The screen freezes.  
3. To resume, press the FREEZE button once more.  
Note:  
For extended periods of time it is recommended that the projector be powered off.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
p Adjusting the Focus/Zoom Manually  
The focus and zoom can be adjusted manually from the projector focus/zoom panel or from the remote control unit. Refer  
to the following guides to adjust the focus and zoom manually.  
Adjusting by Using the OSD Control Panel  
Press the Focus or Zoom button  
on the projector panel to display  
the appropriate window.  
1.  
Adjust the Focus/Zoom using the  
increase and decrease buttons as  
required.  
2.  
Press Cancel to return to the pro-  
jected image.  
3.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
q Changing Lamp Mode  
The projector has two lamp modes available, Normal and Eco. The Normal mode is used for everyday standard projec-  
tion, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following  
guides.  
Changing Lamp Mode by Using the Projector's OSD Control Panel  
Press Menu on the projector's OSD control panel to dis-  
play the Main Menu. Scroll to the  
1.  
Setting menu using Ÿorź and press Select.  
Select the Basic tab using ŻorŹ and select Lamp con-  
trol using Ÿorź. Press Select.  
2.  
From the Lamp control window, select Normal or Eco  
using Ÿorź. Select OK and press Select.  
3.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
Changing Lamp Mode by Using the Remote Control  
Press the Lamp control button on the remote control to ac-  
cess the Lamp control menu.  
1.  
From the Lamp control window, select Normal or Eco us-  
ing Ÿorź. Move the cursor to OK and press Select.  
2.  
Note:  
When the projector is in Eco mode, brightness may be affected.  
Normal Mode: 100% Brightness  
Eco Mode: approx. 85% Brightness  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
r Getting Information  
The Information screen provides details on the life of consumable items within the projector as well as other information  
such as software version. To access the Information screen, refer to the following guide.  
Press Menu on the projector's OSD control  
1.  
panel or remote control to display the Main  
Menu. Scroll to the Information menu using  
Ÿorź and press Select.  
The Usage time menu is displayed as the de-  
fault view. The menu items in this screen are  
for display and cannot be modified.  
2.  
Press Cancel to return to the projected image.  
3.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
s Adjusting Position/Total Dots/Fine Sync  
The Position/Total dots/Fine sync and Keystone Correction can be adjusted manually from the projector's control panel or  
from the remote control unit. Refer to the following guides to adjust the Keystone Distortion manually.  
Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel  
Press the Menu button to display the Main  
1.  
menu. Select the Adjust menu using Ÿorź  
and press Select to display the  
Adjust menu.  
From the Adjust menu, press ŻorŹ to select  
2.  
Image Options and scroll using Ÿorź to  
Horizontal, Vertical, Total dots, or Fine  
sync.  
Adjust the Horizontal, Vertical, Total dots,  
or Fine sync sliding bars using the select  
3.  
ŸźŻŹ buttons.  
Press Cancel to return to the projected image.  
4.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
Correcting Keystone by Using the Remote Control  
IMPORTANT:  
When adjusting the keystone, place the projector in the following position.  
xꢀ Horizontal: set to the lens center  
xꢀ Vertical: set to the maximum top  
Press the Keystone but-  
ton to display the  
Keystone window.  
1.  
Adjust the Horizontal  
2.  
and Vertical sliding bars  
using the select ŸźŻŹ  
buttons.  
Adjust the slide bars until  
3.  
the screen trapezoid is a  
regular shape (see dia-  
gram).  
Press Cancel to return to  
the projected image.  
4.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
Note:  
Holding down the Keystone button for 2 seconds resets the default keystone values.  
ADJUSTMENT  
HORIZONTAL  
VERTICAL  
Keystone  
Max. +/– 35° approx.  
Max. +/– 40° approx.  
The following are conditions under which the maximum angle is achieved:  
ƒꢀ When the standard lens (LNS-S40) is used  
ƒꢀ When the lens shift is set to H for center and V for 0.5 shift.  
ƒꢀ When the lens shift is used and yet you do not get the above-mentioned condition (H for center and V for 0.5 shift),  
you cannot adjust the lens shift correctly.  
ƒꢀ Image is projected in Wide mode  
ƒꢀ Resolution is XGA  
Note:  
Higher resolution than XGA narrows the adjustable range.  
Menu items should be set as follows:  
ƒꢀ Aspect Ratio ........... 4:3  
Horizontal and Vertical are adjusted separately.  
A combination of both adjustments narrows the adjustable range.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
t Preventing the Unauthorized Use of the Projector  
The projector has an built-in security feature to lock the OSD control panels and deny remote control operation. The secu-  
rity feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword.  
Locking the Projector  
To setup the security keyword, refer to the following guide.  
Press Menu on the OSD control panel on the  
1.  
projector or remote control to display the  
Main Menu. Scroll to the Setting menu us-  
ing Ÿorź and press Select.  
The Setting menu is displayed. Select the  
Installation tab using ŻorŹ.  
2.  
Select PIN code lock using Ÿorź. Press  
3.  
Select. You are prompted to enable the PIN  
code lock function. Select On using Ÿorź.  
Select OK and press Select.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
The PIN code window is displayed. Enter a  
PIN code between 4 and 10 characters using  
4.  
ŸźŻŹ. The PIN code characters change  
to “ ”. Press Select.  
*
Once a successful PIN code is entered, a  
confirmation screen is displayed. Enter the  
same password as the previous step and  
write it down for later reference. Press  
Select. A security activation message is dis-  
played. Select Cancel to return to the  
Setting menu or select OK to enable secu-  
rity.  
5.  
CAUTION  
When you have set or changed the PIN code, take a memo and keep it securely. If you forget your  
PIN code, the projector can no longer be started. Contact your dealer or the service center.  
While the projector is locked with the PIN code...  
Put on the label below (supplied) in a prominent place of the projector's body while it is locked with a PIN code.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
Unlocking the Projector  
To unlock the projector, refer to the following guide.  
When the projector is locked, either by re-  
quest during operation or at start up, the  
locked message is displayed.  
1.  
To unlock the projector, press Menu on the  
2.  
control panel or remote control. The PIN  
code window is displayed. Enter the previ-  
ously defined PIN code to activate the  
projector.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Convenient Features  
u Using the Physical Lock  
For security and authorized usage, the projector comes with two types of security features, the Kensington Lock and the  
Security Chain Lock.  
Using the Kensington Lock  
If you are concerned about security, attach the projector to a permanent object with the  
Kensington slot and a security cable.  
Using the Security Chain Lock  
In addition to the password protection function and the Kensington lock, the security chain opening helps protect the  
projector from unauthorized use.  
See the following illustration.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
n Using the Menus  
The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings.  
Navigating the OSD  
You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The  
following illustration shows the corresponding buttons on the remote control and on the projector.  
To open the OSD, press the Menu but-  
1.  
ton on the OSD control panel or remote  
control. There are six initial menus.  
Press the cursor Ÿorź buttons to  
move through the initial menus and  
Select to enter the desired menu.  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Press the cursor Ż or Ź button to  
2.  
3.  
4.  
move through secondary menus.  
Press Ÿorź to select menu items and  
ŻorŹ to change values for settings.  
Press Select to confirm the new setting.  
Press Cancel to close the OSD or leave  
a submenu.  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
o Menu Tree  
The gray shaded areas indicate factory default settings.  
MENU  
ITEM  
Input  
Computer 1, Computer 2, Computer 3, Component, Video, S-Video  
CrossHatch, Raster(0%), Raster(25%), Raster(50%), Raster(100%), Raster Red, Raster  
Green, Raster Blue, Raster Blue 60, Gray Raster 10, Gray Raster 30, Ramp H, Ramp V  
High-bright/Presentation/Video/Movie/Graphic/sRGB  
Test pattern  
Image select  
Adjust  
Image  
High-Bright/Presentation/  
Detail setting  
Basic  
Reference  
Gamma  
Video/Movie/Graphic/sRGB  
Dynamic/Natural/Black detail  
Color  
temp.  
5000K/6500K/7800K/  
8500K/9300K/10500K  
Brilliant color  
Red  
1 to 3  
White balance  
1 to 100  
Green  
1 to 100  
1 to 100  
1 to 100  
1 to 100  
1 to 100  
Blue  
Contrast R  
Contrast G  
Contrast B  
Red, Green, Blue,  
Yellow, Magenta, Cyan  
Color correction  
–60 to 60  
Contrast  
Brightness  
Sharpness  
Color  
0 to 100  
0 to 100  
0 to 31  
0 to 100  
0 to 100  
Tint  
Reset  
Image  
options  
Screen  
4:3/16:9/Side cut/True/Normal  
0%/5%/10%/15%  
Overscan  
PC Adj.  
Horizontal  
Vertical  
±50  
±25  
Total dots  
Fine sync  
Noise reduction  
±50  
0 to 63  
Off/Low/Mid/High  
Video  
3D Y/C separation  
Progressive  
Off/On  
Off/Still/Normal/Movie  
Auto/RGB/SDTV/HDTV  
Color matrix  
Motion adaptive mode  
Motion adaptor/Field Jam/Scaled Field/Mixed Mode  
Off/2-2/2-3 Auto/2-2 On/2-3 On  
Film  
Volume  
Setting  
0~61  
Horizontal  
Vertical  
Basic  
Keystone  
Lamp control  
Lamp mode  
Lamp Interval  
Simple menu  
Normal/Eco  
Dual/Lamp1/Lamp2  
Off/1 week/4 week/2000H  
On/Off  
Language  
English/Deutsch/Français/Italiano/Español/Svenska/Ⱬⶲ儤/ᒳⰍ  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
MENU  
ITEM  
Installation  
Ceiling & Rear  
Desktop Front/Ceiling Rear/Desktop Rear/Ceiling Front  
4800bps/9600bps/19200bps/38400bps  
Communication speed  
Menu color select  
Color/Monochrome  
Display time  
Background  
PIN code lock  
Manual/Auto 5sec/Auto 15sec/Auto 45sec  
Blue/Black/Logo  
Off/On  
Key lock  
Off/On  
Dynamic black  
RC sensor  
Off/On  
Both, Front, Back  
Network setting  
DHCP  
Enable/Disable  
IP address  
Subnet  
Gateway  
DNS  
Network PIN code (0000 to 9999)  
Apply settings  
Standby mode  
PC control  
On start  
Normal/Power-saving  
PC control/Network  
Off/On  
Option  
Power management  
Off/00:05/00:10/00:20/00:30  
Screen trigger  
Fan control  
Off/On  
Normal/Max  
Last/Auto/Computer1/Computer2/Computer3/  
Component/Video/S-Video  
Default input select  
Color system  
Video  
S-Video  
Remote control  
Message  
Auto/NTSC/PAL/SECAM  
Auto/NTSC/PAL/SECAM  
Code1/Code2/Code3/Code4/Code5/Code6/Code7/Code8  
Off/On  
Filter warning  
Search mode  
Off/100[H]/200[H]/500[H]/1000[H]  
Normal/Fine  
Information  
Usage time Lamp1 life remaining, Lamp2 life remaining  
Lamp1 time, Lamp2 time  
PJ time  
Filter time  
Input  
Input name  
Signal  
H-sync freq.  
V-sync freq.  
Video type  
Sync type  
Sync polarity  
Scan type  
Network  
Version  
IP address, Subnet, Gateway, MAC address  
Model name, Serial number, Firmware, Data, Remote control  
Current signal, All data, Clear lamp1 time, Clear lamp2 time, Clear filter time  
Reset  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
p Menu Elements  
Some menus and windows contain large amounts of information in a small area. Refer to the following guide to navigate  
through options more easily.  
Menu windows or dialog windows typically contain the following elements:  
LABEL  
ITEM  
DESCRIPTION  
1
2
3
4
5
6
7
8
Title  
Indicates the menu title.  
Highlight  
Menu type  
Radio button  
Slide bar  
Exit  
Indicates the selected menu or item.  
Advanced Menu or Basic Menu.  
Click this round button to select an option in a dialog box.  
Indicates a representation of adjustable values.  
Return to the previous menu.  
OK  
Accepts changes.  
Cancel  
Reject changes and returns to previous menu.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
q Source Menu Descriptions and Functions  
The Source menu displays all supported image sources.  
Select the required source from the menu using Ÿ or ź and press Select to confirm.  
ITEM  
DESCRIPTION  
Select the source connected to the Computer 1 input  
(see Connecting Your PC or Macintosh Computer on page 26).  
Computer 1  
Select the source connected to the Computer 2 input  
(see Connecting Your PC or Macintosh Computer on page 26).  
Computer 2  
Computer 3  
Component  
Video  
Select the source connected to the Computer 3 input  
(see Connecting Your PC or Macintosh Computer on page 26).  
Select the source connected to the Component input  
(see Connecting Your DVD Player with Component Output on page 29).  
Select the source connected to the Video input  
(see Connecting Your VCR or Laser Disc Player on page 30).  
Select the source connected to the S-Video input  
(see Connecting Your VCR or Laser Disc Player on page 30).  
S-Video  
Displays information about the type of test pattern (Range: CrossHatch, Raster (0%), Raster (25%),  
Raster (50%), Raster (100%), Raster Red, Raster Green, Raster Blue, Raster Blue 60, Gray Raster  
10, Gray Raster 30, Ramp H, Ramp V).  
Test Pattern  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
r Adjust Menu Descriptions and Functions  
The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix.  
Three tabs are accessible through the Adjust menu, Picture, Image Options and Video.  
Image menu  
The image menu is used to alter picture settings and can be accessed from the Adjust menu.  
The following table lists all functions with a description and the default setting.  
ITEM  
Image select  
DESCRIPTION  
Select a set of preset values using Ż or Ź from the list. Notice that the below values will  
change depending on the preset selection.  
Detail Setting  
Contrast  
See s Detail Settings Menu Descriptions and Functions on page 67.  
Adjust the Contrast value using ŻorŹ to highlight the differences between light and dark  
areas of the picture.  
Brightness  
Adjust the Brightness value using ŻorŹ to lighten or darken the picture.  
Adjust the Sharpness value using ŻorŹ to sharpen or blur the borders between colors and  
objects.  
Sharpness  
Color  
Tint  
Adjust the Color value using ŻorŹ to increase or decrease color input to the picture.  
Adjust the Tint value using ŻorŹ to increase or decrease the color Hue of the picture.  
The settings and adjustments are set to initial factory settings.  
Reset  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Image options menu  
The Image Options menu is used to configure image options such as screen positioning and aspect ratio. Access the im-  
age options menu in the Adjust menu.  
The following table lists all functions with a description and the default setting.  
ITEM  
Screen  
DESCRIPTION  
Select Screen using ŻorŹ from the list (see page 63).  
Set the Overscan value using ŻorŹ (see page 63).  
Overscan  
Adjust the position values using the slides.  
Horizontal: Adjusts the image location horizontally using ŻorŹ.  
Vertical:  
Adjusts the image location vertically using ŻorŹ.  
Total dots: Fine tune a computer image or remove any vertical banding that might appear.  
Fine sync: Adjust the clock phase or reduce video noise, dot or cross talk.  
PC adj.  
Note:  
Only use the Phase settings after the total dots settings have been modified.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Screen  
The screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image.  
4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen.  
16:9 – A wide-screen aspect ratio for video.  
Side cut – Crops the image.  
True – Displays the current image in its true resolution.  
Normal – Displays the current image in its aspect ratio.  
Overscan  
Video images normally exceed the size of the display screen. The edge of the picture may or may not be displayed cor-  
rectly. The border area that is cropped can be adjusted by using the Overscan menu.  
Set the overscan percentage between 0 – 15% to compensate for different screen sizes.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Video menu  
The Video menu is used to configure image options such as film. Access the Video menu in the Adjust menu.  
The following table lists all functions with a description and the default setting. A detailed description follows the table.  
ITEM  
Noise reduction  
3D Y/C separation  
Progressive  
Color matrix  
Film  
DESCRIPTION  
Select Noise reduction mode (see page 65).  
Select 3D Y/C separation mode (see page 65).  
Select Progressive mode (see page 65).  
Select Color matrix mode (see page 65).  
Select Film mode (see on page 65).  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Noise reduction  
Select the level of noise reduction required.  
Range: Off, Low, Mid, High.  
3D Y/C separation  
3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce  
clearer and sharper images without overlapping colors (rainbow effect).  
Set 3D Y/C Separation On or Off.  
Progressive  
Progressive converts an interlaced image to a progressive scan image.  
Select the form of Deinterlacing required from:  
Still – Select for stills such as slide projections or screen shots.  
Normal – Select Normal for non-specialized projection.  
Movie – Select for movie projection.  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Color matrix  
Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color  
space.  
Select from the following:  
Auto – Auto selects the color matrix.  
RGB – Sets the color matrix to RGB, use for PC monitor or camera imaging.  
SDTV – Sets the color matrix to SDTV, use for Standard Definition imaging.  
HDTV – Sets the color matrix to HDTV, use for High Definition imaging.  
Film  
Film aids in converting motion picture film images into video. The process adds additional frames to the picture in order to  
increase the frame rate.  
Note:  
This feature is only available when Progressive is turned on and SDTV  
signal is selected.  
Select from the following:  
Off – Film mode is turned off.  
2-2/2-3 Auto – Detects pull-down correction method.  
2-2 On – Uses 2-2 pull-down correction method.  
2-3 On - Uses 2-3 pull-down correction method.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
s Detail Settings Menu Descriptions and Functions  
The Detail settings menu contains basic and advanced color adjustment options such as gamma correction, color contrast  
and color correction.  
Basic  
The Basic tab contains general Detail Settings such as gamma correction and color temperature. Access to the General  
tab is through the Detail Settings menu.  
The following table lists all functions with a brief description.  
ITEM  
Reference  
DESCRIPTION  
Set Reference mode (see page 68).  
Gamma  
Select Gamma Correction mode (see page 68).  
Move the slider bar left or right to set the color temperature value in Kelvin (K). Compensate  
for the amount of light available. Daylight is approximately 5500K.  
Color temp.  
Move the slider bar left or right to set the BrilliantColorTM value. BrilliantColor extends the  
exposure range and sharpens detail for grain free images.  
BrilliantColor  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Reference  
The Reference mode allows the projector to differentiate between source materials for example movies, PC images or  
video stills.  
Select from the following:  
High-bright – Select for use in a brightly lit room.  
Presentation – Select if the projector is to be used for presentation purposes.  
Video – Select for video projection.  
Movie – Select for Movie projection.  
Graphic – Select Graphic for still images.  
sRGB – Select for projecting PC or web page images.  
Gamma  
Gamma enables adjustment to the light intensity (brightness) of an image in order to match the source more closely.  
Select from the following:  
Dynamic – Allows the projector to alter the gamma correction automatically.  
Natural – Attempts to emulate the original source as closely as possible.  
Black detail – Black detail highlights boundaries between light and dark areas of the image more clearly.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
White balance  
White Balance allows the projector to compensate for different colors of light being emitted by different light sources.  
The following table lists all functions with a brief description.  
ITEM  
Red  
DESCRIPTION  
Set the value to compensate for red light sources.  
Green  
Set the value to compensate for green light sources.  
Blue  
Set the value to compensate for blue light sources.  
Contrast R  
Contrast G  
Contrast B  
Set the Contrast R value to compensate for red light sources.  
Set the Contrast G value to compensate for green light sources.  
Set the Contrast B value to compensate for blue light sources.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Color correction  
The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color,  
characteristics or add more of a particular color.  
The following table lists all functions with a brief description.  
ITEM  
DESCRIPTION  
Red  
Increase or decrease the amount of red in the projected output using Ż and Ź.  
Increase or decrease the amount of green in the projected output using Ż and Ź.  
Increase or decrease the amount of blue in the projected output using Ż and Ź.  
Increase or decrease the amount of yellow in the projected output using Ż and Ź.  
Increase or decrease the amount of magenta in the projected output using Ż and Ź.  
Increase or decrease the amount of cyan in the projected output using Ż and Ź.  
Green  
Blue  
Yellow  
Magenta  
Cyan  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
t Setting Menu Descriptions and Functions  
The Setup menus contain the most often used settings during installation and options to customize the general output of  
the projector. Three tabs are accessible through the Setup menu, general, installation and option.  
Basic  
The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with  
the projector control panel or with the remote control unit.  
The following table lists all functions with a brief description.  
ITEM  
Keystone  
DESCRIPTION  
Adjust the Keystone trapezoid (see Keystone page 72).  
Lamp control  
Lamp mode  
Lamp interval  
Simple menu  
Language  
Select Lamp control. Range: Normal or Eco.  
Select Lamp configuration. Range: Dual, Lamp1 or Lamp2.  
Select Lamp interval. Range: Off, 1 week, 4 weeks or 2000 hours.  
Displays menus with minimum essential options. This setting is best suited to novices.  
Select the OSD language (see Language on page 74).  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Keystone  
The keystone trapezoid can be adjusted by selecting this option.  
Select Horizontal or Vertical using Ÿorź then, use ŻorŹ to adjust the projected image appearance as required.  
IMPORTANT:  
When adjusting the keystone, place the projector in the following position.  
xꢀ Horizontal: set to the lens center  
xꢀ Vertical: set to the maximum top  
Lamp control  
Select Normal or Eco from the lamp mode window. The lamp life can be extended by using the Eco mode and the fan  
noise can be reduced.  
Lamp mode  
Select the lamps to be used for projection.  
Select from the following:  
Dual – Uses both lamps simultaneously.  
Lamp1 – Uses Lamp1 only.  
Lamp2 – Uses Lamp2 only.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Lamp interval  
The period of time for regulating lamp usage when not in dual lamp mode.  
Select from the following:  
Off, 1 week, 4 weeks and 2000H  
Simple menu  
Select the Simple menu to display.  
Set Simple menu On or Off.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Language  
Select the OSD language to be used.  
Select from the following:  
ƒꢀ English  
ƒꢀ German  
ƒꢀ French  
ƒꢀ Italian  
ƒꢀ Spanish  
ƒꢀ Swedish  
ƒꢀ Japanese  
ƒꢀ Simplified Chinese  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Installation  
The Installation tab contains menu options for various setup conditions such as orientation and remote sensor mode and is  
accessed through the Setup menu.  
The following table lists all functions with a brief description.  
ITEM  
Ceiling & Rear  
DESCRIPTION  
Select from four projection methods depending on projection site  
(see Ceiling & Rear page 76).  
Select Communication speed.  
Range: 4800bps, 9600bps, 19200bps, 38400bps  
Communication speed  
Menu color select  
Display time  
Select the menu color from the list.  
Range: color or monochrome.  
Select Display time.  
Range: Manual, Auto 5s, Auto 15s, Auto 45s  
Select Background appearance when there is no signal.  
Range: blue, black or logo  
Background  
PIN code lock  
Set PIN code lock On/Off (see PIN Code Lock on page 79).  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
ITEM  
DESCRIPTION  
Set Control panel lock On/Off.  
Note:  
Key lock  
y This Control Panel Lock does not affect the remote control functions.  
y When the control panel is locked, pressing and holding the Cancel button  
on the projector cabinet for about 10 seconds. The setting will change to Off.  
DynamicBlackTM improves the black level of the projector. Black level is the darkest  
part of a picture and varies between viewing devices and environments.  
Set DynamicBlack on/off.  
DynamicBlack  
Set RC sensor fields.  
Range: Both, Front, Back  
RC sensor  
Network setting  
Standby mode  
Opens Network preferences tab (see Network setting on page 80).  
Select Standby mode.  
Range: Normal and Power-saving  
Enables the path selection for PC control.  
Range: PC control or Network.  
PC control  
Ceiling & Rear  
Ceiling & Rear enables you to set how the projected image is displayed.  
Select from the following:  
Desktop Front – Standard forward facing projection (Default setting).  
Desktop Rear – Standard rear projection. Enables the projector to produce the image from behind the screen by reversing  
the image.  
Ceiling Front – Forward facing ceiling mounted projection. Enables ceiling mounted projection by inverting the image.  
Ceiling Rear – Rear ceiling mounted projection. Enables ceiling mounted projection from behind the screen by inverting  
and reversing the image.  
Desktop front  
Ceiling rear  
Desktop rear  
Ceiling front  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Communication speed  
Select communication speed to set the baud rate of the connection.  
Note:  
Longer cable connections may require lower settings.  
Select from the following options:  
ƒꢀ 4800bps  
ƒꢀ 9600bps  
ƒꢀ 19200bps  
ƒꢀ 38400bps  
Note:  
In the Network mode, Communication Speed function is not available.  
Menu color select  
Select color mode to set the menu color.  
Select from the following options:  
ƒꢀ Color  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
ƒꢀ Monochrome  
Display time  
Sets the amount of time a menu is displayed.  
Select from the following:  
Manual – Menus stay on screen until the Menu button is pressed again.  
Auto 5 secs—Menu is displayed for 5 seconds.  
Auto 15 secs – Menu is displayed for 15 seconds.  
Auto 45 secs – Menu is displayed for 45 seconds.  
Background  
Background enables you to display a blue/black screen when there is no signal. The default background is blue.  
Select from the following:  
ƒꢀ Blue  
ƒꢀ Black  
ƒꢀ Logo  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
PIN Code Lock  
See t Preventing the Unauthorized Use of the Projector on page 51 – 53.  
Key lock  
Turn On/Off the Key Lock function for cabinet buttons.  
Note:  
y This Control Panel Lock does not affect the remote control functions.  
y When the control panel is locked, pressing and holding the Cancel button on the projector cabinet for  
about 10 seconds. The setting will change to Off.  
DynamicBlack  
DynamicBlackTM enables you to improve the black level of the projector.  
RC sensor  
Set the operating range for the wireless remote control.  
Select from the following:  
ƒꢀ Both  
ƒꢀ Front  
ƒꢀ Back  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Network Setting  
See Network setting on page 82.  
Standby mode  
There are two standby modes available: Normal and Power-saving. Power-saving mode allows you to put the projector in  
the standby condition to consume less power than Normal.  
Note:  
Be sure to connect the projector and computer while the projector is in standby mode and before turning on  
the computer.  
Select from the following:  
ƒꢀ Normal  
ƒꢀ Power-saving  
Note:  
The HTTP server functions are not available during Power-saving mode.  
The MONITOR OUT function is not available during Power-saving mode.  
Control through the PC Control connector and Network mode is not available during Power-saving mode.  
For PC control and Network mode of the projector it is recommended to leave the projector in the Normal  
mode.  
Normal mode:  
POWER indicator: Orange light  
WARNING indicator: Green light  
POWER indicator: Orange light  
WARNING indicator: Off  
Power-saving mode:  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
PC control  
This function enables you to select the path for PC control (see r PC Control Codes and Cable Connections  
on page 115).  
Note:  
In the Network mode, Communication Speed function is not available.  
Select from the following:  
ƒꢀ PC control  
ƒꢀ Network  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Network setting  
The Network setting tab is accessed by using the Setup/Installation tab and contains the general LAN settings.  
The following table lists all functions with a description and the default setting.  
ITEM  
DESCRIPTION  
DHCP  
Select either a static IP or DHCP IP setting by selecting the appropriate radio button.  
Displays the IP address.  
IP address  
Subnet  
Displays the subnet mask.  
Gateway  
DNS  
Enable or disable the network gateway setting. Click on the radio button to change the setting.  
Enable or disable the DNS server settings. Click on the radio button to change the setting.  
A password can be set to restrict access to the setting pages of the projector using the web  
browser. The default password is "0000".  
Range: 0000 ~ 9999  
Network PIN code  
Apply settings  
Apply and save settings.  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Option  
The Option tab contains miscellaneous setup menu settings such as Power Management and Default Input Select and can  
be accessed by using the Setting Menu.  
The following table lists all functions with a description and the default setting.  
ITEM  
On start  
DESCRIPTION  
Set this item on to enable the projector to power up when AC plug in.  
Range: On or Off  
Select the amount of time the projector remains idle before powering down.  
Range: Off, 0:05, 0:10, 0:20, 0:30  
Power management  
Screen trigger  
Set this item to On to enable the projector to automatically lower the projection screen when  
powering on.  
Range: On or Off  
Select Fan control.  
Range: Normal or Max (see Fan control page 85)  
Fan control  
Select the default input for projection.  
Range: Last, Auto, Computer1, Computer2, Computer3, Component, Video, S-Video  
Default input select  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
ITEM  
DESCRIPTION  
This option switches remote control codes.  
Range: Code 1, Code 2, Code 3, Code 4, Code 5, Code 6, Code 7, Code 8  
Remote control  
Message  
This option turns on or off messages.  
Range: Off or On  
Set this item to on to have the projector display a message when the air filter needs servicing.  
Range: Off, 100[H], 200[H], 500[H], 1000[H]  
Filter warning  
Search mode  
This feature sets the Auto Adjust mode.  
Range: Normal, Fine  
On start  
On start enables the projector to start automatically when the power cable is connected to an active power outlet and the  
main power switch is on. This eliminates the need to always use the POWER (On) button on the remote control or projec-  
tor cabinet. To use the On start function, you must first press the main power switch to On before connecting the power  
cable.  
Note:  
y When the projector is off by using the POWER button (or put in the standby mode) and the power cable is  
disconnected, On start will not activate after power (AC) is applied.  
y When the projector is off by using the Direct Power Off function or after the power (AC) is removed (no  
standby mode), On start will be activated after power (AC) is applied.  
y The Direct Power Off function means you can turn off the power (AC) to the projector by using a power  
strip equipped with a switch and a breaker.  
Power management  
Power management enables the projector to automatically turn off if there is no signal received by any input.  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Select from the following:  
ƒꢀ Off  
ƒꢀ 5 minutes  
ƒꢀ 10 minutes  
ƒꢀ 20 minutes  
ƒꢀ 30 minutes  
Screen trigger  
Set Screen trigger to On to enable the projector to automatically lower the projection screen when powering on. When  
powering off, Screen trigger stops sending a low voltage trigger to the screen controller and the screen goes up.  
Fan control  
Fan control is used to set the speed of the internal cooling fan. Set Fan Speed to Max in altitudes over 1500 meters (5000  
feet).  
The Fan control option default is Normal, which enables the projector to automatically detect fan requirements. For higher  
temperature locations or prolonged use, the Max option is available to provide greater cooling capacity.  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Default input select  
The Default input is the image source that the projector will search for automatically on startup.  
Last – Uses the most recently used image source.  
Auto – Auto detects the default image source.  
Computer1/2/3 – Uses Computer1, 2 or 3 as the default image source.  
Component – Uses last component as the default image source.  
Video – Uses last video input as default image source.  
S-Video – Uses last S-video input as default image source.  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Remote control  
This projector has eight different remote control codes; the factory set normal mode (Code 1) and the other seven codes  
(Code 2 to Code 8). This switching function prevents remote control operation mixture (jam) when operating several projec-  
tors or video equipment together.  
To change the code of Projector:  
To change the Remote control code of the projector used in ON SCREEN MENU is selectable from Code 1 to Code 8.  
Message  
This option turns on or off messages. Even though selecting [Off], the following message will appear. “Projector is locked”  
when the projector security is unlocked, the message will disappear.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Filter warning  
Set Filter warning to have the projector display a message when the air filter needs servicing.  
The message below shows when this function is activated.  
Search mode  
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise and  
stability. You can automatically make adjustments in two ways: [Normal] and [Fine].  
Normal: The RGB image will be automatically adjusted. Normally select this option (Default).  
Fine: Select this option if fine adjustment is needed. It takes more time to switch to the source than the Normal settings.  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
u Information Menu Descriptions and Functions  
The information menu provides only screens for the quick access of menus. The Information menu contains four distinct  
tabs.  
Usage time  
The Usage Time tab displays information about lamp usage and remaining lamp life.  
The following table lists all items with a description.  
ITEM  
Lamp1 Life remaining  
Lamp2 Life remaining  
Lamp1 time  
DESCRIPTION  
Displays the Lamp1 life remaining as a percentage.  
Displays the Lamp2 life remaining as a percentage.  
Displays the Lamp1 total usage in hours.  
Lamp2 time  
Displays the Lamp2 total usage in hours.  
PJ time  
Displays the projector total usage in hours.  
Displays how many hours the filter has been used.  
Filter time  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Input  
The Input tab displays various source and frequency values at a glance.  
The following table lists all items with a description.  
ITEM  
Input name  
DESCRIPTION  
Displays the Input Terminal that is presently being used  
(see Default input select on page 86).  
Displays the Source name of the signal presently being used  
(see Option on page 83).  
Signal  
H-sync. freq.  
V-sync. freq.  
Video type  
Sync type  
Displays Horizontal frequency in KHz.  
Displays Vertical frequency in Hz.  
Displays Video type.  
Displays Sync type.  
Sync polarity  
Scan type  
Displays Sync polarity.  
Displays Scan type.  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Network  
The Network tab displays LAN settings as previously defined (see Network setting on page 82).  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
Version  
The Version tab displays all the version and product details of the projector and associated software (for display only).  
The following table lists all items with a description.  
ITEM  
Model name  
Serial number  
Firmware  
DESCRIPTION  
Displays Product ID.  
Displays projector Serial number.  
Displays Firmware version and Color Wheel currently installed (4-seg or 6-seg).  
Displays remote control code.  
Remote control  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Using On-Screen Display  
v Reset Menu Descriptions and Functions  
Occasionally, circumstances may require that factory defaults be reset, for demonstration purposes for example, or when  
components are replaced.  
The Reset menu contains options for returning settings to the factory default and is accessed by using the Main menu.  
The following table lists all items with a description.  
ITEM  
DESCRIPTION  
Reset the adjustments for current signal to factory preset levels. All items in Adjust can  
be reset.  
Current signal  
Resets all options to factory default regardless of when they were changed.  
Reset all the adjustments and settings for all the signals to the factory preset except Language,  
Background, Key lock, Security, Network Mode, Communication Speed, Lamp life re-  
maining, Lamp time, and Filter time.  
All data  
Clear lamp1 time  
Clear lamp2 time  
Clear filter time  
Reset lamp1 time  
These options should only be used when components are  
Reset lamp2 time  
cleaned or replaced (see 6. Maintenance on page 94)  
Reset filter hours  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
n Cleaning the projector  
Cleaning the Cabinet  
Refer to the following guide to clean the projector cabinet.  
1. Wipe off dust with a clean dampened cloth.  
2. Moisten the cloth with warm water and mild detergent and wipe the cabinet.  
3. Rinse all detergent from the cloth and wipe the projector again.  
CAUTION  
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.  
Cleaning the Lens  
Refer to the following guide to clean the projector lens.  
1. Apply a little optic lens cleaner to a clean, lint free cloth (do not apply the cleaner directly to the lens).  
2. Lightly wipe the lens in a circular motion.  
Do not use abrasive cleaners or solvents.  
CAUTION  
To prevent discoloration or fading, avoid getting cleaner on the projector case.  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Cleaning the Filters  
The projector uses three filters to keep the fans free of dust and other particles, and should be cleaned every 500 hours of  
operation. In dusty environments, it is recommended to clean the filters more frequently. If the filter is dirty or clogged, your  
projector may overheat. When the message below is displayed, the filters must be cleaned.  
Note:  
When the Please clean filter message is displayed, please clean or replace all three filters at the same  
time to synchronize the Filter time display.  
The Filter Message item should be enabled in the Options menu. Refer to Option on page 83.  
Refer to the following guide to clean the filters.  
Bottom view  
Lift the projector to expose the under-  
side to locate the first filter.  
See the drawing on the right.  
1.  
Note: Only clean the outside of the ex-  
haust vents with a vacuum cleaner.  
The left-side filter and intake grille (lo-  
cated in the rear) can be cleaned as  
demonstrated in the following images.  
2.  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
The rear filter can be  
accessed as shown.  
3.  
Once the filters are cleaned, please reset the filter hours by using the Clear filter time option in the  
v Reset Menu Descriptions and Functions on page 93.  
Note:  
Using the projector without the air filter fitted inside, dirt and dust are sucked into the projector, causing fail-  
ure.  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
o Replacing Consumable Parts  
During the course of normal usage, consumable parts become worn out resulting in reduced performance. The following  
guides detail how to replace the various consumable parts within the projector quickly and safely.  
xꢀ Before replacing any of the parts, please take note of the following:  
xꢀ Ensure that the projector is turned off and disconnected from the power supply.  
xꢀ Ensure that the projector is in a clean, stable position before replacing parts.  
xꢀ Allow at least one hour after shutdown for the projector to cool before attempting replacing any consumable parts.  
xꢀ Do not interchange Lamp 1 and Lamp 2 after the projector has been used once.  
Doing so will not allow the projector to display the correct lamp usage hours.  
xꢀ A minimum space is required for replacement. See page 24 and 98 for more details.  
Replacing the Filters  
When the lamps are replaced, the filters should also be replaced, not cleaned.  
Refer to the following guide to replace the filters.  
CAUTION  
Do not drop the projector on your hand or fingers while lifting the projector to replace the filters. Doing so  
could injure your hand or fingers.  
Note:  
The filters on the side and the rear are located on the bottom.  
Gently slide the filter covers in the di-  
rection shown.  
1.  
Lift the foam from all three filters in  
2.  
the direction shown. Remove com-  
pletely from the filter cover and  
discard.  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Insert replacement foam and press  
down firmly.  
3.  
Replace the filter covers by pushing  
gently in the direction shown.  
4.  
Once the filters are replaced, please reset the filter hours by using the Clear filter time option in the  
v Reset Menu Descriptions and Functions on page 93.  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Replacing the Lamps  
When a lamp reaches the end of it’s usable life, the following message is displayed. Replace the lamp.  
The projection lamps should be replaced when they burn out. They should only be replaced with a certified replacement  
part, contact your local dealer if unsure.  
Note:  
1. Lamps are positioned differently. Take care not to force the lamps when replacing.  
2. Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or sin-  
gle lamp mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear  
as a lamp failure.  
3. Lamps last approximately 2000-2100 hours (2500-2600 hours in Eco mode) and the End of lamp life  
message is displayed during the lamps' final 100 hours of operational life. Please replace during 2000-2100  
hour.  
Important:  
1. The lamp contains a certain amount of mercury and should be disposed of according to local ordinance  
regulations.  
2. Avoid touching the glass surface of the new lamp: doing so may shorten its operation life.  
Lamp Handling Precautions  
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling  
may result in accidents, injury, or create a fire hazard.  
xꢀ Lamp life may differ from lamp to lamp and according to the environment of use. There is no guar-  
antee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter period  
of time than other similar lamps.  
xꢀ If the projector indicates that the lamp should be replaced, i.e., if LAMP 1 and/or LAMP 2 light up,  
replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow care-  
fully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp  
with LAMP 1 and/or LAMP 2 lighted may increase the risk of lamp explosion.  
CAUTION  
xꢀ A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as  
its lifetime draws to an end. Risk of explosion may differ according to the environment or condi-  
tions in which the projector and lamp are being used.  
If a lamps explodes, the following safety precautions should be taken:  
Disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service station  
for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are  
no broken shards or pieces of glass around the projector or coming out from the cooling air circulation  
holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the pro-  
jector except those who are authorized trained technicians and who are familiar with projector service.  
Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to  
do so, may result in an accident or injury caused by pieces of broken glass.  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Check the lamp number to be replaced by using Information Menu.  
Turn off the projector and disconnect the AC plug. Allow the projector to cool for at least 60 minutes.  
Loosen the screw on the lamp cover  
(A), and remove the lamp cover as  
shown (B).  
1.  
Loosen the two captive screws on  
the lamp module (A). Lift the mod-  
ule handle up as shown (B).  
2.  
Pull firmly on the module handle in  
the direction shown to remove the  
lamps.  
3.  
Reverse steps 1 to 3 to install the  
new lamp module and replace the  
lamp cover.  
4.  
100  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Maintenance  
Resetting the Lamp Time Counter  
After replacing the lamp(s), the lamp hour counter(s) should be reset to zero. Refer to the following guide:  
Press the Menu button on the OSD  
control panel or Remote Control to  
open the Main menu.  
1.  
Press the Ÿorź button to move to  
the Reset menu and press Select.  
2.  
The Reset menu is displayed. Se-  
3.  
lect Clear lamp1 time or Clear  
lamp2 time as required using  
Ÿorź and press Select.  
A confirmation box is displayed.  
4.  
Select OK using Ż or Ź and  
press Select to reset the selected  
Lamp hours to zero.  
Ordering a Replacement Lamp  
Replacement lamp can be ordered through your dealer. When ordering, give the following information to the dealer.  
xꢀ Model No. of your projector: PDG-DXT10L, PDG-DXT10KL  
xꢀ Replacement Lamp Type No: POA-LMP117  
(Service Parts No. 610 335 8406)  
101  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
n Troubleshooting  
Indicator Messages  
Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on  
the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the  
projector through the WARNING LED (see OSD Controls and Status LEDS on page 8 for location). The following tables  
describe the various states of the 4 LEDs.  
The POWER LED  
PROJECTOR STATUS  
LED CONDITION  
Off  
LED SEQUENCE  
PROJECTOR CONDITION  
AC off  
Off  
Off  
0.5 secs on  
0.5 secs off  
Cooling  
Orange blink  
Green blink  
After power off  
Start up  
0.5 secs on  
0.5 secs off  
Power up sequence  
Standby  
Orange on  
Green on  
On  
On  
Standby  
On  
Power on  
The WARNING LED  
PROJECTOR STATUS  
LED CONDITION  
LED SEQUENCE  
PROJECTOR CONDITION  
Normal condition  
Cover ERROR  
Off  
Off  
Power on  
Red 1 time blink  
(repeatedly)  
0.5 secs on  
2.5 secs off  
ERROR  
ERROR  
ERROR  
ERROR  
Red 2 times blink  
(repeatedly)  
(0.5 secs ON > 0.5 secs  
OFF) * 2 > 2.0 secs OFF  
Temperature ERROR  
Power ERROR  
Fan ERROR  
(0.5 secs ON > 0.5 secs  
OFF) *3 > 2.0 secs OFF  
Red 3 times blink  
Red 4 times blink  
(repeatedly)  
(0.5 secs ON > 0.5 secs  
OFF) * 4 > 2.0 secs OFF  
Keylocked  
(when push key)  
Keylocked function  
enabled  
Orange light up  
On  
Standby  
(Power-saving)  
Standby  
(Power-saving)  
Off  
Off  
On  
Standby (Normal)  
Green light  
Standby (Normal)  
102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
The LAMP LEDs  
PROJECTOR STATUS  
LED CONDITION  
Off  
LED SEQUENCE  
PROJECTOR CONDITION  
Lamp off  
Off  
Lamp off  
0.5 secs on  
0.5 secs off  
End of the lamp life  
Red blink  
Replace lamp  
ERROR  
Red 1 time blink (re-  
peatedly)  
0.5 secs on  
2.5 secs off  
No lamp  
Red 6 times blink (re-  
peatedly)  
(0.5 secs ON > 0.5 secs  
OFF) * 6 > 2.0 secs OFF  
Lamp ERROR  
Cooling lamp  
Re-light up sequence  
ERROR  
0.5 secs ON > 0.5 secs  
OFF  
Orange blink  
Green blink  
Switching lamp1 and 2  
Start up  
0.5 secs ON > 0.5 secs  
OFF  
Lamp life over  
Eco mode  
Red on  
On  
On  
On  
Replace lamp  
Power on  
Orange on  
Green on  
Normal mode  
Power on  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
Common Problems and Solutions  
These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains  
unsolved, contact your dealer for assistance.  
Often the problem is something as simple as a loose connection. Check the following before proceeding to the problem-  
specific solutions.  
xꢀ Use some other electrical device to confirm that the electrical outlet is working.  
xꢀ Ensure the projector is turned on.  
xꢀ Ensure all connections are securely attached.  
xꢀ Ensure the attached device is turned on.  
xꢀ Ensure a connected PC is not in suspend mode.  
xꢀ Ensure a connected notebook computer is configured for an external display. (This is usually done by press-  
ing an Fn-key combination on the notebook.)  
Tips for Troubleshooting  
In each problem-specific section, try the steps in the order suggested. This may help you to solve the problem more  
quickly.  
Try to pinpoint the problem to avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.  
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical sup-  
port or for passing on to service personnel.  
104  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
o Image Problems  
Problem: No image appears on the screen  
1. Verify the settings on your notebook or desktop PC.  
2. Turn off all equipment and power up again in the correct order.  
Problem: The image is blurred  
1. Adjust the Focus on the projector.  
2. Press the AUTO PC ADJ. button on the remote control or projector.  
3. Ensure the projector-to-screen distance is within the specified range.  
4. Check that the projector lens is clean.  
5. Remove the lens cover.  
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possible.  
2. Use the Keystone button on the remote control to correct the problem.  
Problem: The image is reversed or upside down  
zꢀ Check the Ceiling & Rear setting on the Setting menu of the OSD.  
Problem: The image is streaked  
1. Set the Total dots and Fine sync. settings on the Adjust menu of the OSD to the default settings.  
2. To ensure the problem is not caused by a connected PC’s video card, connect to another computer.  
Problem: The image is flat with no contrast  
1. Adjust the Contrast setting on the Adjust menu of the OSD.  
2. Adjust the Brightness setting on the Adjust menu of the OSD.  
Problem: The color of the projected image does not match the source image.  
zꢀ Adjust the Color temp. and Gamma settings on the Detail setting menu of the OSD.  
Lamp Problems  
Problem: There is no light from the projector  
1. Check that the power cable is securely connected.  
2. Ensure the power source is good by testing with another electrical device.  
3. Restart the projector in the correct order and check that the Power LED is green.  
4. If you have replaced the lamp recently, try resetting the lamp connections.  
5. Replace the lamp module.  
6. Remove the lens cap.  
7. Put the old lamp back in the projector and have the projector serviced.  
Problem: The lamp goes off  
1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the projector.  
When the Power LED is orange, press the power button.  
2. Replace the lamp module.  
3. Put the old lamp back in the projector and have the projector serviced.  
105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Appendix  
Remote Control Problems  
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2. Ensure the path between remote and sensor is not obstructed.  
3. Turn off any fluorescent lights in the room.  
4. Check the battery polarity.  
5. Replace the batteries.  
6. Turn off other Infrared-enabled devices in the vicinity.  
7. Have the remote control serviced.  
8. Ensure that the remote control code conforms to the projector's code.  
9. Ensure that the reset switch in the compartment lid on back of the remote control is set to use  
position.  
Audio Problems  
Problem: There is no sound  
1. Adjust the volume on the remote control.  
2. Adjust the volume of the audio source.  
3. Check the audio cable connection.  
4. Test the source audio output with other speakers.  
5. Have the projector serviced.  
Problem: The sound is distorted  
1. Check the audio cable connection.  
2. Test the source audio output with other speakers.  
3. Have the projector serviced.  
p Having the Projector Serviced  
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton.  
Include a description of the problem and a checklist of the steps you took when trying to fix the problem. The information  
may be useful to the service personnel. Return the projector to the place you purchased it.  
106  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
n Projector Specifications  
This section provides technical information about the projector's performance.  
Optical Specifications  
ITEM  
DESCRIPTION  
Single DLP® chip, 4 segment color wheel  
Projection system  
Resolution  
Lamp  
1024 x 768 pixels* (up to UXGA @ 60 Hz, up to SXGA+ @ 60 Hz on DVI-D)  
260 W AC (230 W in Eco mode), Dual lamp system  
50" - 200" / 1.27m - 5.08m (LNS-W41)  
40" - 500" / 1.02m – 12.7m (LNS-W40, LNS-S40, LNS-T40, LNS-T41)  
Image size (diagonal)  
LNS-W41: Power focus, throw ratio 0.77:1, F2.0, f=11.4 mm  
LNS-W40: Power zoom and focus, throw ratio 1.33-1.79:1, F1.8-2.3, f=19.3-25.8 mm  
LNS-S40: Power zoom and focus, throw ratio 1.78-2.35:1, F1.7-1.9, f=26-34 mm  
LNS-T40: Power zoom and focus, throw ratio 2.22-4.43:1, F2.1-2.9, f=32-63 mm  
LNS-T41: Power zoom and focus, throw ratio 4.43-8.3:1, F2.2-3.1, f=63.5-117.4 mm  
Lens options  
Lens shift  
Vertical + 0.5V, Horizontal +/- 0.1H (LNS-W40, LNS-S40, LNS-T40, LNS-T41)  
*Effective pixels are more than 99.99%  
107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Electrical Specifications  
ITEM  
DESCRIPTION  
1 Analog RGB (Mini D-Sub 15P), 1 Analog RGB R/Cr, G/Y, B/Cb, H, V  
(BNC x 5), 1 Digital RGB (DVI-D 24P), 1 Component Y, Cb/Pb, Cr/Pr  
(RCA x 3), 1 Component (Mini D-Sub 15P) shared with COMPUTER 1  
IN, 1 S-Video (Mini DIN 4P), 1 Video, 3 Stereo Mini Audio, 2  
(L/R) RCA Audio, 1 Remote Control (Stereo Mini)  
Inputs  
Outputs  
Control  
1 RGB (Mini D-Sub 15P), 1 Stereo Mini Audio, 1 Screen Trigger  
1 PC Control Port (D-Sub 9P), 1 GPIO (Mini D-sub 15P)  
1 B Type (for Service)  
USB Port  
LAN Port  
RJ-45  
NTSC, NTSC4.43, PAL, PAL-60/N/M/B/G/H/I), SECAM, HDTV: 1080i, 720p, SDTV: 576p,  
576i, 480p, 480i  
Video Compatibility  
Scan Rate  
Horizontal: 15 kHz, 31 to 90 kHz (RGB: 31 kHz or over) Vertical: 50 Hz to 85 Hz  
RGB: 100 MHz (-3dB)  
Video Bandwidth  
Color Reproduction  
Horizontal Resolution  
16.7 million colors simultaneously, Full color  
NTSC / NTSC4.43 / PAL / PAL-M / PAL-N / PAL60: 540 TV lines  
SECAM: 300 TV lines  
RGB: 1024 dots (H) x 768 dots (V)  
External Control  
Sync Compatibility  
Built-in Speakers  
Power Requirement  
Input Current  
RS232, IR, LAN, GPIO  
Separate Sync / Composite Sync / Sync on G  
3W x 2  
100 - 240V AC, 50/60Hz  
7.7A  
108  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
ITEM  
DESCRIPTION  
655W in Dual Lamp Normal mode / 580W in Dual Lamp Eco mode  
350W in Single Lamp Normal mode / 315W in Single Lamp Eco mode  
< 30W in Standby mode Normal  
Power Consumption  
< 5W in Standby mode Power saving  
Mechanical Specifications  
ITEM  
DESCRIPTION  
19.9" (W) x 7.6" (H) x 15.2" (D)  
Dimensions  
Weight  
505 mm (W) x 192 mm (H) x 385 mm (D)  
(not including protrusions)  
36.3 lbs/16.5 kg  
Environmental Considerations  
ITEM  
DESCRIPTION  
Operational Temperatures  
Storage Temperatures  
41qꢀto 104qF / 5qꢀto 40qC, 10% to 90% humidity (non-condensing)  
14qꢀto 140qF (-10qꢀto 60qC), 5% to 90% humidity (non-condensing)  
Regulations  
UL/C-UL Approved (UL 60950-1, CSA 60950-1)  
Meets FCC Class B requirements  
Meets DOC Canada Class B requirements  
Meets AS/NZS CISPR.22 Class B  
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)  
Meets Low Voltage Directive (EN60950-1, TÜV GS Approved)  
109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Optional Parts  
The parts listed below are optionally available. When ordering those parts, specify the item name and Model No. to the  
sales dealer.  
Standard Zoom Lens  
Long Zoom Lens  
: LNS-S40  
: LNS-T40  
Ultra Long Zoom Lens  
Short Zoom Lens  
: LNS-T41  
: LNS-W40  
: LNS-W41  
: POA-CW01  
: POA-CA-RC30  
Fixed Short Zoom Lens  
Six-segment Color Wheel  
Wired Remote Cable (30m)  
110  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
o Cabinet Dimensions  
111  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
p Pin Assignments of Mini D-Sub 15 Pin Input Connector  
Signal Levels  
Video signal: 0.7Vp-p (Analog)  
Sync signal:  
TTL level  
PIN NUMBER  
RGB SIGNAL (ANALOG)  
YCBCR SIGNAL  
1
2
Red  
Cr  
Y
Green or Sync on Green  
Blue  
3
Cb  
4
Ground  
5
Ground  
6
Red Ground  
Cr Ground  
Y Ground  
Cb Ground  
7
Green Ground  
Blue Ground  
No Connection  
Sync Signal Ground  
No Connection  
Bi-directional DATA (SDA)  
8
9
10  
11  
12  
13  
Horizontal Sync or Composite  
Sync  
14  
15  
Vertical Sync  
Data Clock  
112  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
q Compatible Input Signal List  
The following table shows compatible signal types, their resolution and frequency refresh rates.  
Horizontal: 15kHz, 31kHz to 90 kHz  
Vertical: 50 Hz to 85 Hz  
RESOLUTION  
(DPI)  
FREQUENCY REFRESH  
RATE (KHZ)  
FREQUENCY REFRESH  
SIGNAL  
RATE (HZ)  
60.00  
50.00  
60.00  
50.00  
59.94  
66.67  
72.81  
75.00  
85.01  
56.25  
60.32  
72.19  
75.00  
85.06  
74.55  
60.00  
70.07  
74.93  
75.03  
85.00  
75.00  
NTSC  
PAL  
–
–
15.73  
15.63  
15.73  
15.63  
31.47  
35.00  
37.86  
37.50  
43.27  
35.16  
37.88  
48.08  
46.88  
53.67  
49.72  
48.36  
56.48  
60.24  
60.02  
68.68  
67.50  
–
–
PAL60  
SECAM  
VESA  
MAC  
–
–
–
–
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 864  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
VESA  
MAC  
VESA  
VESA  
MAC  
VESA  
VESA  
VESA  
113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
RESOLUTION  
(DPI)  
FREQUENCY REFRESH  
RATE (KHZ)  
FREQUENCY REFRESH  
RATE (HZ)  
SIGNAL  
VESA  
D
D
D
–
1280 x 960  
1280 x 1024  
1400 x 1050  
1920 x 1080  
1920 x 1080  
1280 x 720  
1280 x 720  
–
60.00  
63.98  
65.30  
33.75  
28.13  
45.00  
37.50  
31.25  
31.47  
15.73  
15.63  
60.00  
VESA  
60.02  
VESA  
60.00  
HDTV (1080i)(1125i)  
HDTV (1080i)(1125i)  
HDTV (720p)(750p)  
HDTV (720p)  
SDTV(576p)(625p)  
SDTV (480p)(525p)  
DVD YCbCr  
60.00 Interlace  
50.00 Interlace  
60.00 Progressive  
50.00 Progressive  
50.00 Progressive  
59.94 Progressive  
59.94 Interlaced  
50.00 Interlaced  
–
–
–
–
–
–
–
–
DVD YCbCr  
–
–
Note:  
Images above flagged with "D" are supported by digital signal.  
An image with higher or lower resolution than the projector’s native resolution (1024 x 768) will be com-  
pressed.  
Some Composite and Sync on Green signals may not be displayed correctly.  
Signals other than those specified in the table above may not be displayed correctly. If this should happen,  
change the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for  
procedures.  
114  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
r PC Control Codes and Cable Connections  
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port.  
Connect a RS-232C serial cross cable to  
SERIAL PORT IN on the projector and serial  
port on the PC.  
1.  
Launch a communication software provided  
with PC and setup the communication condi-  
tion as follows:  
2.  
Baud rate  
Parity check : none  
Stop bit : 1  
Flow control : none  
Data bit : 8  
: 38400 bps  
Type the command for controlling the projec-  
tor and then enter the "Enter" key.  
3.  
Example  
When you want to change the input to Computer 2, Type “C” “0” “6” “Enter.”  
The below table shows the typical command lists for controlling the projector. Please consult your local dealer for further  
information of another commands.  
Functional Execution Command Table  
COMMAND  
C00  
FUNCTION  
COMMAND  
C3A  
FUNCTION  
Turn the projector ON  
Pointer RIGHT  
Turn the projector OFF  
(immediately OFF)  
Selects Computer 1  
Selects Computer 2  
Selects Computer 3  
Selects Component  
Volume UP  
Volume DOWN  
Audio mute ON  
Audio mute OFF  
Video mute ON  
Video mute OFF  
Aspect 4:3  
C01  
C3B  
Pointer LEFT  
C05  
C06  
C07  
C08  
C09  
C0A  
C0B  
C0C  
C0D  
C0E  
C0F  
C10  
C1C  
C1D  
C33  
C34  
C3C  
C3D  
C3F  
C46  
C47  
C4A  
C4B  
C5D  
C5E  
C5F  
C60  
C89  
C8E  
C8F  
C90  
C91  
Pointer UP  
Pointer DOWN  
Enter  
Zoom DOWN  
Zoom UP  
Focus DOWN  
Focus UP  
Lens shift UP  
Lens shift DOWN  
Lens shift LEFT  
Lens shift RIGHT  
Auto PC Adj.  
Keystone UP  
Keystone DOWN  
Keystone RIGHT  
Keystone LEFT  
Aspect 16:9  
Menu ON  
Menu OFF  
Selects Video  
Selects S-video  
115  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Status Read Command Table  
COMMAND  
FUNCTION  
CR0  
CR6  
Status Read  
Temperature Read  
PC Control Connector (DIN-9P)  
Note:  
1. Pin 1, 4, 6 and 9 are not used.  
2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify the cable  
connection.  
3. For long cables, it is recommended to set communication speed within projector menus to 9600 bps.  
116  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
s Screen Trigger  
When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the  
screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the  
screen controller and the screen will go up.  
Note:  
To use this feature, you must turn on the Screen Trigger function. See Screen Trigger on page 85 for more  
information.  
Note:  
Screen controllers are supplied and supported by screen manufacturers.  
Note:  
Do not use this jack for anything other than intended use. Connecting the wired remote control to the  
SCREEN TRIGGER Mini Jack causes damage to the remote control.  
117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
t Operation Using HTTP Browser  
Overview  
The use of HTTP server functions will allow control of the projector from a web browser without the installation of special  
software. Please be sure to use “Microsoft Internet Explorer 4.x” or a higher version for the web browser. (This device uses  
“JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will vary depend-  
ing on the version of browser. Please refer to the help files and the other information provided in your software).  
Access is gained to the HTTP server functions by specifying the following address in the entry column of the URL:  
http:// <the projector’s IP address> /index.html  
http:// <the projector's IP address> /lanconf.html  
Note:  
The display or button responses can be slowed down or operation may not be accepted depending the set-  
tings of your network. Should this happen, consult your network administrator. The projector may not  
respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a moment and re-  
peat. If you still can’t get any response, turn off and back on the projector.  
Preparation Before Use  
Make network connections, set up the projector and confirm that it is complete before engaging in browser operations  
(see Network setting on page 80 for more information).  
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the set-  
ting method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not  
be displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in  
operation. It is recommended that a proxy server not be used unless it is unavoidable.  
Handling of the Address for Operation by Using a Browser  
Regarding the actual address that is entered for the address or entered to the URL column when operation of the projector  
is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the projector  
has been registered to the domain name server by a network administrator, or the host name corresponding to the IP ad-  
dress of the projector has been set in the “HOSTS” file of the computer being used.  
Example 1:  
When the IP address of the projector is 192.168.73.1, access is gained to the HTTP server functions by specifying  
http://192.168.73.1/index.html for the address or the entry column of the URL.  
118  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Configuring Network Settings  
The Network Settings screen is displayed as follows:  
http:// <the projector's IP address> /lanconf.html  
Domain  
Host Name: Type in a hostname. Up to 60 alphanumeric characters can be used.  
Domain Name: Type in domain name of the network connected to the projector. Up to 60 alphanumeric characters can be used.  
Apply: Click to reflect the entries.  
Mail  
Alert Mail: Click “Enable” to enable Alert Mail feature. This option notifies your computer of an error message via e-mail  
when using wired LAN. The error message will be notified when the projector lamp has reached the end of its usable life or  
an error occurs in the projector.  
Sender's Address: Specify the sender’s address. Up to 60 alphanumeric and symbols, characters can be used.  
SMTP Server Name: Type in the SMTP server name to be connected to the projector. Up to 60 alphanumeric characters  
can be used.  
Recipient's Address 1 to 3: Type in your recipient's address. Up to 60 alphanumeric and symbols characters can be  
used.  
Apply: Click to apply the settings.  
119  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Test Mail  
Send a test mail to check if your settings are correct. Click to “Execute” to enable this feature.  
Test Mail Status Button: Click to display the test result.  
Sample of a message sent from the projector:  
Projector Name: X X X X  
Lamp 1 or 2 Hours Used: xxxx [H]  
The lamp is at the end of its usable life. Please replace the lamp.  
Note:  
If you entered an incorrect address in a test, you may not receive an Alert mail. Should this happen, check if  
the Recipient's Address is correctly set.  
Unless any one of the [Sender's Address], [SMTP Server's Name] or [Recipient's Address 1-3] is selected,  
[Test Mail] is not available.  
PJLink  
This option allows you to set a password when you use the PJLink feature.  
On/Off: Enable or disable the password.  
Password: Enter a password (up to 32 characters)  
Note:  
PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This stan-  
dard protocol is established by Japan Business Machine and Information System Industries Association  
(JBMIA) in 2005.  
The projector supports all the commands of PJLink Class 1.  
PROJECTOR INPUT  
Computer 1  
Computer 2  
Video  
PJLINK INPUT  
RGB 1  
PARAMETER  
11  
12  
21  
22  
23  
31  
RGB 2  
VIDEO 1  
VIDEO 2  
VIDEO 3  
DIGITAL 1  
S-Video  
Component  
Computer 3  
120  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
Structure of the HTTP Server  
Once the projector is connected to a network and configured correctly, the following screen is displayed through the web  
browser.  
http:// <the projector's IP address> /index.html  
FUNCTION  
SETTING  
DESCRIPTION  
Power Panel  
On  
This controls the power to the projector  
Off  
Volume Panel  
Mute Panel  
Ÿ – Increases the volume adjustment value  
This controls the volume of the projector  
ź – Decreases the volume adjustment value  
Picture On – Mutes the video  
This controls the mute functions of the projector  
Picture Off – Cancels the video muting  
Sound On – Mutes the audio  
Sound Off – Cancels the audio muting  
OSD On – Mutes the on-screen display  
OSD Off – Cancels the muting of the on-screen display  
All On – Mutes each of the video, audio, and on-screen display func-  
tions  
All Off – Cancels the muting of each of the video, audio, and on-  
screen display functions  
Image Panel  
Brightness Ÿź – Increases or decreases the brightness adjustment  
value  
Controls the video adjustments of the projector  
Contrast Ÿź – Increases or decreases the contrast adjustment value  
Color Ÿź – Increases or decreases the color  
adjustment value  
Tint Ÿź – Increases or decreases the hue  
adjustment value  
Sharpness Ÿź – Increases or decreases the  
sharpness adjustment value  
121  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
FUNCTION  
SETTING  
DESCRIPTION  
Input Select Panel  
Computer1 – Switches to the COMPUTER 1 IN connector  
Computer2 – Switches to the COMPUTER 2 IN connector  
Computer3 – Switches to the COMPUTER 3 IN connector  
Component – Switches to the COMPONENT IN connectors  
Video – Switches to the VIDEO IN connector  
This switches the input connector of the projector  
S-Video – Switches to the S-VIDEO IN connector  
Projector Status Panel  
Refresh – Updates the panel with the latest  
information available  
This displays the status of selected projector functions  
Lamp1 life remaining – Displays the remaining life of Lamp 1 as a  
percentage  
Lamp2 life remaining – Displays the remaining life of Lamp 2 as a  
percentage  
Lamp1 time – Displays the number of hours Lamp 1 has been used  
Lamp2 time – Displays the number of hours Lamp 2 has been used  
PJ time – Displays the number of hours the project has been used  
Error Status – Displays the status of errors  
occurring within the projector  
Note:  
The functions that can be controlled will vary depending on the signal being input to the projector  
(see o Selecting an Input Source on page 34 for more information).  
122  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. Specifications  
u 15 Pin GPIO Control  
Type: 15Pin D-SUB black female type  
PIN NO.  
SHORT/OPEN  
FUNCTION  
14  
SHORT  
OPEN  
EXTERNAL CONTROL MODE ON  
EXTERNAL CONTROL MODE OFF  
5
POWER ON  
POWER OFF  
SHORT  
OPEN  
10  
PICTURE MUTE ON  
PICTURE MUTE OFF  
SHORT  
OPEN  
3
SOUND MUTE ON  
SOUND MUTE OFF  
SHORT  
OPEN  
4, 8, 12, 11  
11  
12  
8
4
OPEN  
OPEN  
OPEN  
OPEN  
OPEN  
OPEN  
OPEN  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
OPEN  
OPEN  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
OPEN  
OPEN  
OPEN  
SHORT  
SHORT  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
OPEN  
SHORT  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
OPEN  
SHORT  
COMPUTER1  
VIDEO1  
S-VIDEO1  
COMPONENT  
NOT AVAILABLE  
COMPUTER2  
NOT AVAILABLE  
NOT AVAILABLE  
COMPUTER3 (DVI)  
NOT AVAILABLE  
NOT AVAILABLE  
NOT AVAILABLE  
NOT AVAILABLE  
NOT AVAILABLE  
NOT AVAILABLE  
NOT AVAILABLE  
Note:  
The term “SHORT” is defined as having a connection to pin 15.  
123  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Troubleshooting Check List  
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by referring  
to the n Troubleshooting section on page 102 of your user’s manual. This checklist below will help us solve your problem  
more efficiently.  
Frequency of Occurrence always sometimes (How often?________) other (________)  
Power  
No power (POWER indicator does not light green) See also “Status Indica-  
tor (WARNING)”.  
Shut down during operation.  
Power cable's plug is fully inserted into the wall outlet.  
Lamp cover is installed correctly.  
Power cable's plug is fully inserted into the wall outlet.  
Main power switch is pressed to the ON position.  
Lamp cover is installed correctly.  
Power Management is turned off.  
Lamp Time (lamp operation hours) was cleared after lamp replacement.  
Video and Audio  
No image is displayed from your PC or video equipment to the projector.  
Parts of the image are lost.  
Still no image even though you connect the projector to the PC first,  
then start the PC.  
Still unchanged even though you press the AUTO PC ADJ. button.  
Still unchanged even though you carry out [Reset] in the projector’s  
menu.  
Enabling your notebook PC’s signal output to the projector.  
A combination of function keys will enable/disable the external display.  
Usually, the combination of the “Fn” key along with one of the 12 func-  
tion keys turns the external display on or off.  
Image is shifted in the vertical or horizontal direction.  
Horizontal and vertical positions are correctly adjusted on a computer  
signal.  
No image (blue background, logo, no display).  
Input source's resolution and frequency are supported by the projector.  
Some pixels are lost.  
Still no image even though you press the AUTO PC ADJ. button.  
Still no image even though you carry out [Reset] in the projector’s  
menu.  
Image is flickering.  
Still unchanged even though you press the AUTO PC ADJ. button.  
Signal cable's plug is fully inserted into the input connector  
A message appears on the screen.  
Still unchanged even though you carry out [Reset] in the projector’s  
menu.  
( __________________________________ )  
Image shows flickering or color drift on a computer signal.  
Image appears blurry or out of focus.  
The source connected to the projector is active and available.  
Still no image even though you adjust the brightness and/or the con-  
trast.  
Still unchanged even though you checked the signal’s resolution on PC  
and changed it to projector’s native resolution.  
Input source's resolution and frequency are  
supported by the projector.  
Still unchanged even though you adjusted the focus.  
No sound.  
Image is too dark.  
Audio cable is correctly connected to the audio input of the projector.  
Still unchanged even though you adjusted the volume level.  
AUDIO OUT is connected to your audio equipment.  
Remains unchanged even though you adjust the brightness and/or the  
contrast.  
Image is distorted.  
Image appears to be trapezoidal (unchanged even though you carry out  
the [Keystone] adjustment).  
Other  
Remote control does not work.  
Buttons on the projector cabinet do not work.  
Control Panel Lock is not turned on or is disabled in  
No obstacles between the sensor of the projector  
and the remote control.  
the menu.  
Projector is placed near a fluorescent light that can  
disturb the infrared remote controls.  
Still unchanged even though you press and hold the  
CANCEL button for a minimum of 10 seconds.  
Batteries are new and are not reversed in installa-  
tion.  
The remote control code conforms to the projector's  
code.  
124  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Troubleshooting Check List  
In the space below please describe your problem in detail.  
Information on application and environment where your projector is used  
Projector  
Installation environment  
Model number:  
Screen size: inch  
Serial No:  
Screen type:  
White matte  
Beads  
Polarization  
Date of purchase:  
Wide angle High contrast  
feet/inch/m  
Lamp operating time (hours):  
Information on input signal:  
Horizontal synch frequency  
Vertical synch frequency  
Lamp Mode:  
Normal  
Eco Throw distance:  
Orientation: Ceiling mount  
Power outlet connection:  
Connected directly to wall outlet  
Desktop  
[
[
] kHz  
] Hz  
Synch polarity H  
V
(+)  
(+)  
(–)  
(–)  
Connected to power cord extender or other (the number  
of connected equipment______________)  
Synch type  
Separate  
Sync on Green  
WARNING Indicator:  
Composite  
Connected to a power cord reel or other (the number  
of connected equipment______________)  
Steady light  
Orange  
Green  
Flashing light [  
] cycles  
Remote control model number:  
Signal cable  
Computer  
SANYO standard or other manufacturer’s cable?  
Manufacturer:  
Model number:  
Notebook PC / Desktop  
Native resolution:  
Refresh rate:  
Model number:  
Distribution amplifier  
Model number:  
Switcher  
Length:  
inch/m  
Model number:  
Adapter  
Video adapter:  
Other:  
Model number:  
Video equipment  
VCR, DVD player, Video camera, Video game or other  
Manufacturer:  
Model number:  
125  
Download from Www.Somanuals.com. All Manuals Search And Download.  
KT3AL  
SANYO Electric Co., Ltd.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Raypak Swimming Pool Heater 180A User Guide
Renesas Network Card M3T FLX 42SPB User Guide
Roadmaster Car Stereo System VRCD220S User Guide
Ryobi Planer AP13AK User Guide
Samsung Home Theater System AH68 01663S User Guide
Sanyo Battery Charger N 1200SCK User Guide
Savin All in One Printer 9915DP User Guide
Savin Printer 3460DNP User Guide
Seiko Printer BX 900 User Guide
Senco Power Screwdriver DS200 D2 User Guide