index
POA-PN03C
D
8
C
V
DC
O
100m
U
T
A
V
ID
T
E
C
O
A
I
N
LINK
PJ-Net Organizer plus IIC
Network Capture 3
Network Viewer 3
Network Communication
OWNER'S MANUAL
XP57 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance and Caution
CAUTION ON USE IN NETWORk
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network, you
must perform the safety inspections periodically. In this case you must pay attention to
the change of environment in which you installed the projector. It may cause fire or an
accident depending on the change of environment.
CAUTION
SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data or
damage of the computer caused by usung this product.
The CE Mark is a Directive conformity mark of the European Community (EC).
NOTES ON Lithium Battery (CALIFORNIA USA ONLY)
This product uses a Lithium Battery which contains Perchlorate Material - special han-
dling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Notas acerca de pilas de litio (SOLO PARA CALIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene el material perclorato – puede ser nec-
esario una manipulación especial.
Consulte la página www.dtsc.ca.gov/hazardouswaste/perchlorate
PJ-NET ORGANIZER
ꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Compliance..........................................................................................................................................................................2
Operating environment of PJ-Net Organizer............................................................................................... 11
Chapter 2 Installation...............................................................................................15
Flow of installation........................................................................................................................................................16
[2] Installation and network configuration....................................................................................................18
Mounting ..................................................................................................................................................................18
Network PIN code setting..............................................................................................................................22
Notice about system construction...........................................................................................................24
Chapter 3 Basic Setting and Operation.............................................................29
1 Enter the IP address........................................................................................................................................30
3 Display of main setting page ...................................................................................................................31
How to use the setting page.................................................................................................................................32
Initial setting.....................................................................................................................................................................34
Network PIN code setting..............................................................................................................................35
Date and time setting.......................................................................................................................................36
Network configuration...............................................................................................................................................37
E-mail setting...................................................................................................................................................................38
Chapter 4 Controlling the Projector...................................................................45
Sound .........................................................................................................................................................................51
Menu ...........................................................................................................................................................................51
PC adjustment.................................................................................................................................................................52
Setting up the projector...........................................................................................................................................53
Timer setting....................................................................................................................................................................57
Check the timer events....................................................................................................................................58
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Register the projector.......................................................................................................................................64
Chapter 5 Network Capture...................................................................................69
Commands on the task bar...........................................................................................................................70
Parameter set up..................................................................................................................................................71
[2] Control by the web browser..................................................................................................................74
Advanced using example...............................................................................................................................76
How to use the Network Communication....................................................................................................81
Start the communication................................................................................................................................81
Join the communication (only for Sub PC)..........................................................................................81
Exit from the communication (only for Sub PC) ..............................................................................81
End the communication..................................................................................................................................81
Acquire and release of editing authority..............................................................................................81
Chapter 6 Network Viewer.....................................................................................87
Creating a program file [Program Editor].......................................................................................................93
[1] Control by the web browser..................................................................................................................98
Examples of connection........................................................................................................................................106
Examples: OS/Browsers.......................................................................................................................................... 109
Product specification................................................................................................................................................113
Port specification.........................................................................................................................................................114
Q&A......................................................................................................................................................................................115
PJ-NET ORGANIZER
ꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
Features
Real Time Capture function (+p.72)
To display the screen image of
the computer by the projec-
tor through the network in real
time.
PC1
PC2
PC4
Capture
PC3
PC6
PC6
PC6
PC5
Network Communication function (+p.77)
To communicate by sharing the
captured image of a computer
with multiple computers and
a projector. User can draw the
text and figure on the captured
image by using a drawing tool.
PJ1
Capture
PC1
PC2
PC5
Capture a screen
image of PC5 and
make marking with
a tool.
Network Viewer function (+p.87)
To acquire the JPEG image data
from the file servers placed in
the network and project them
by the projector.
PJ2
PJ1
PC1
PC2
JPEG
PC3
PC4
PC5
Prog.
JPEG
FTP file server
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Web Management function (+p.45)
With this function, you can
monitor projector functions
PJ2
PJ1
PC1
PC2
such as power status, lamp
status, input mode, signal
condition, lamp-use time, etc.
through the network by using
the web browser installed on
your computer.
PC3
PC4
PC6
PC5
Turn ON PJ2
E-Mail Alert function (+p.38)
The projector (Network Unit)
sends messages to the regis-
PJ2
PJ1
PC1
PC2
tered e-mail addresses when
a lamp abnormality or power
failure occurs with the projec-
tor. This message describes
PC3
PC4
PC6
PC5
how to solve the cause of the
problems. You can take efficient
action for quick recovery.
You’ve got
Mail.
PJ Camera Viewer function (refer to the separated booklet)
By using the supplied camera,
PJ1
PJ2
PJ3
PJ4
PJ Camera Viewer takes pictures
of the projected images of the
projector located on the remote
places, and stores pictures into
your computer via the network.
JPEG
JPEG
JPEG
JPEG
PC6
PC5
P
JPEG
PJ-NET ORGANIZER
ꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
SNMP Agent function (+p.42)
To send the information of the
PJ1
PJ2
PJ3
PJ4
projector to the SNMP manager.
Enables you to manage the pro-
jector condition with the SNMP
manager software.
Trap
PC6
PC5
P
You received
a Trap.
Trap
SNMP Manager
Multi-control function (+p.62)
A single computer can con-
trol and set up the multiple
PJ1
PJ2
PJ3
PJ4
projectors at the same time.
PC6
PC5
PC4
Select Input2 for
PJ1 to PJ4.
Automatic On/Off using Clock function (+p.57)
Automatically turn on or off the
projectors at specified date/day
and time by using the clock func-
tion.
I am ready to turn ON,
and select Input 3 (Video)
Now it’s 11:30
SNMP Manager function (refer to the separated booklet)
A function to manage the
condition of projectors in the
PJ1
PJ2
PJ3
PJ4
network by using the SNMP
protocol. The managing com-
puter needs to provide an
SNMP managing software. Refer
to the owner's manual of the
"PJ Network Manager" supplied
separately for further details.
Trap
PC6
PC5
PC4
You received
a Trap.
Trap
SNMP Manager
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Environment
Operating environment of PJ-Net Organizer
To perform the managing and setting of the projector by using this product, the environ-
ment described below is required.
Standard mode
Windows 98, Windows Me, Windows NT4.0SP6
Windows 2000, Windows XP
Operating System
Higher than Pentium III 900MHz
Recommended CPU
Memory
64MB (Minimum)/ 128MB or more(Recommended)
128MB or more for WindowsXP
100MB or more
HDD free area
CD-ROM drive
Drive equipment
Support one of following resolutions;
VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of col-
ors: Either of 16 bit (65,536 color 24/32 bit (16,77 million colors))
Display setting of
computer
The computer must provide a 10Base-T or 100Base-TX network
card.
Network card
Internet Explorer version 5.0, 5.5 or 6.0
Netscape Navigator version6.2, 7.0 or 7.1
* Used to control and set up the projector. The layout of pages in
the browser may slightly differ from each type of application or
operating system you use.
Web Browser*
Adobe Flash Player version 6,0,79,0(6.0r79) or later
Plug-Ins
- Microsoft Outlook
- Netscape Mail
* Required the internet e-mail application software to receive an
e-mail alert sent from this product. If you do not use the function
E-mail Alert, this application is not required.
- Microsoft Outlook Express
Internet Mailer*
- FTP server (Windows 2000 Professional or Windows XP
Professional)
* The FTP service provided with the Windows 2000 Professional
or Windows XP Professional is required when using the Network
Viewer function.
FTP Service *
This product is designed for the projectors listed below.
PLC-XP57 seires, PLC-XT20 series, PLC-XT25 series
* For the operating environment of PJ Networj Manager and PJ Camera Viewer,
refer to each owner's manual in the document CD-ROM.
PDA restriction
1
The PDA can be used for the Light mode* only. The operating system of the PDA is
PocketPC2002 or higher. The version of the Adobe Flash Player is 6,0,81,0 or higher.
*1 The "Light Mode" and "Standard Mode" will be explained on item "Display Mode" (+ p.30-32)
PJ-NET ORGANIZER
11
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
*1
The limitation of connection between this product and hub or computer
Suitable LAN cables are limited by length and type as follows;
Connection
Type of usable LAN cable
Maximum length
100m
2
Network Unit - Hub
UTP Straight Cable with category 3 or 5 *
2
Network Unit - Computer UTP Cross Cable with category 3 or 5*
100m
*1 There may be other limitations depending on your network environment or LAN specification.
Please consult your network administrator for further details.
*2 Category of LAN cable indicates the cable quality. Normally, a cable with category 3 or 5 is used
for 10Base-T network, and a cable with category 5 is used for 100Base-TX network.
Before use
Package contains
The package contains following items. Check each item as you unpack the package. If you
have any of the following items missing, contact the sales dealer.
❑ Network unit
1 piece
T
C
A
K
N
I
L
Q
Guide
u
ic
k
S
e
tu
p
❑ Quick Setup Guide
1 piece
1 piece
English/Japanese
❑ Software CD-ROM
NetworkViewer&Capture3software
PJNetworkManagersoftware
❑ Document CD-ROM
1 piece
PJ-NetOrganizerOwner'sManual
PJNetworkManagerOwner'smanual
PJCameraViewerOwner'smanual
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Before use
Following contents are required to use the PJ Camera Viewer function.
❑ Network Camera
1 piece
Camera Packaging box
❑ Software CD-ROM
1 piece
PJCameraViewersoftware
❑ Camera mounting tool set
Hookandloopfastener(big)
Hookandloopfastener(small)
Cablefixer
1piece
1piece
1piece
1piece
1piece
1piece
Envelope
Ferritecore
Double-sidedadhesivetape*
Safetyrope*
* For use of the double-sided adhesive tape and the safety
rope, refer to the caution cards.
PJ-NET ORGANIZER
1ꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Preparation
Notice
Expression/Abbreviation
The word "projector" found in this manual means "projector provided with Network unit"
unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows XP
Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruc-
tion procedures may differ from the actual operation depending on your computer envi-
ronment.
Use of this manual
This manual does not provide the description of basic operation and functions for com-
puter, web browser, projector and network. For instructions about each piece of equip-
ment or application software, please refer to the respective booklet.
Trademarks
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows
NT are registered trademarks of Microsoft Corporation. Internet Explorer is a registered
trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator are
trademarks or registered trademarks of Netscape Communications Corporation. JavaScript
is a registered trademark of Sun Microsystems, Inc. PJLink is a registered trademark of
JBMIA (Japan Business Machine and Information System Industries Association).
Other product or brand names in this manual are registered trademarks or trademarks of
their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Flow of installation
The following are instructions for attaching this product to the projector and connecting it
to the network. Please review the entire procedure to become familiar with it.
Function of the network unit (+ p.17)
Explains the name and functions of each part of the network unit.
1
2
Installation and network configuration (+ p.18-24)
1 Mount this product onto the projector.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the network unit.
4 Set the Network PIN code.
Installation of the software (+ p.25-27)
Explains how to install the software Network Viewer & Capture 3 into your com-
puter.
3
Set up is complete
The preparation is completed to control the projector connected to the network. At next
step, set up and control the projector via the network by using the web browser installed
on your computer. Please see chapter 3 "Basic setting and operation". (+ p.29)
For the installing the camera and PJ Camera Viewer and operating instructions,
refer to the separated owner's manual of PJ Camera Viewer.
1ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Name and function of each part
[1] Name and function of each part
(Top View)
POWER indicator
This lights up red when the network
function is set ON in the projector
menu.
D
8
C
V
DC
O
100m
U
T
A
Mounting screws
Mount by using a coin etc. (+ p.18)
V
ID
T
E
C
O
A
I
N
LINK
ACT indicator
This turns on and off with green when
sending or receiving of data
LINk indicator
This lights up red when the network unit is
connected to the network correctly.
(Bottom View)
Connector plug
Connecting to the terminal on the pro-
jector. (+ p.18)
UT
O
A
DC
DC 8V 100m
Power jack for Camera
Used to connect the camera power cable
(refer to separated owner's manual)
Video input jack for Camera
Used to connect the camera video cable
(refer to separated owner's manual)
N
I
O
E
D
I
V
LAN port
Connecting the LAN cable. (+ p.19)
PJ-NET ORGANIZER
17
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
[2] Installation and network configuration
Mounting
1 Disconnect the AC plug from the projector.
Connector cover
2 Remove the connector cover and screw
covers (2 pieces) from the projector and
insert plug on this product to the option
connector.
Screw cover
3 Tighten two screws by using a coin
etc.
!
Caution
✐ AC cord must be disconnected when mounting or removing this product otherwise it may dam-
age the product.
✐ Do not install multiple network units into a projector otherwise it may damage the product.
✐ Connect the AC cord after connecting the LAN cable and computer.
1ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable
with RJ-45 plug. There are two different types of cables depending on whether the network is
constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distrib-
ute the network cable if required.
1 Disconnect the AC plug from the projector.
2 Connect the UTP straight cable to the LAN
port on the network unit.
3 Connect the UTP straight cable to the hub.
Hub
(10Base-T, 100Base-TX)
Projector
UTP straight cable
✐ Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5. When
you connect the projector into the 100Base-TX network, use cable with category 5.
✐ The length of cable between hub and projector should be less than 100m.
PJ-NET ORGANIZER
1ꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Network configuration
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for this
product are activated automatically. If not activated, the product may not have been
installed correctly. Please check item "Mounting" (+ p.18).
Configure the network
Before performing the network configuration, prepare network address numbers (IP
Address, Subnet Mask, Default Gateway, DNS) assigned to the projector. Ask your network
administrator for the network address.
For example, the case where the following network address is set up is explained.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.1.201
: 255.255.255.0
: 192.168.1.1
: 0.0.0.0
The default network configuration is set as follows.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
T
C
A
K
IN
L
: 0.0.0.0
1 Selection of network menu
Turn on the projector and display the menu on the screen. Select network icon from the
main menu and then press SELECT button once. Check that the mode is "On". If not,
change mode to "On" using the point buttons (7,8).
Network icon
Select "On" or "Off"
with 7,8 button
✐ The network unit begins restarting each time the mode is set "On".
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
1
2
2 Configuration for IP Address/ Sub net/ Gateway* /DNS*
Press SELECT button again. The following network setting pallet appears on the screen.
Enter the specified network addresses.
The red frame moves
sequentially left or right
with 7 8 button.
The number up or
down with d e but-
ton.
How to enter the numbers
There are 2 ways to enter the numbers, one is by using the point buttons (d e ) on
the remote control or on the projector, the other is by using the screen 10-key pallet by
which the numbers can be entered directory. For further information see "How to enter
the numbers with the screen 10-key pallet" (+ p.23).
3 Fixing the network configuration
After completing the entering of address, select "SET" and
press SELECT button. The network unit starts re-booting
and displays message "Please wait..." on the screen until
the re-booting is complete. Do not disconnect the AC
cord during this period. After that the network setting pallet will disappear on the screen.
Completing of installation
Now the installation is complete. The IP address of this projector is set to "192.168.1.201".
Item
Description
IP address.............Sets IP address of the projector
Sub net...................Sets Subnet mask. Normally sets 255.255.255.0
1
Gateway* .............Sets IP address of the default gateway (Router)
2
DNS* .......................Sets IP address of the DNS server. Must be set when using the e-mail function
✐
Refer to the projector's owner's manual for operation of the projector.
*1 In the network environments not using a Gateway or Router, the Gateway address should be set to [0.0.0.0].
*2 If you do not use the functions E-mail or DNS server, it is also set [0.0.0.0] for the DNS address.
PJ-NET ORGANIZER
ꢀ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Network PIN code setting
The Network PIN code can be set to restrict access to the setting page of the projector
using the web browser.
✐ Default Network PIN code [0000] means no Network PIN code is set.
1 Displaying Network PIN code menu
Select network menu and then select "Network PIN code" sub menu. Press SELECT but-
ton twice to display the Network PIN code entry pallet.
* The number on the pallet is the current Network PIN code.
Network PIN Code
The red frame moves
sequentially left or right
with 7 8 button.
The number up or down
2 Entering the Network PIN code
with d e button.
To enter the Network PIN code, use point buttons
(▲,▼,7,8) on the projector or the remote con-
trol.
3 Fixing the Network PIN code
After entering a 4-digit number, select "SET" by
using point buttons (7,8) and then press SELECT
button.
✐ The screen 10-key pallet can be used for entering the Network PIN code. See item "How to enter
the numbers with the screen 10-key pallet" (+. 23)
✐ It is recommended to set up the Network PIN code when you connect the projector to the net-
work. This setting is carried out through the projector’s menu and also it can be set through the
network using the web browser. For further information, refer to item "Initial setting/Network PIN
code setting" (+ p.35).
✐ Valid characters for the Network PIN code are only numbers 0 to 9. The number "0000" means no
Network PIN code is set.
✐ This Network PIN code is not to restrict the use of the projector. This Network PIN code is to set
the security against the use of the projector through the network.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
How to enter the numbers with the screen 10-key pallet
1 Select a column with a red frame by using the point buttons 7 8 .
2 Press SELECT button. The screen 10-key pallet appears on the screen.
3 By using the point buttons(d e 7 8), select numbers 0 to 9 and press SELECT button. By
repeating the above to enter the complete number on the column.
*To change the number in a column, select “C” and press SELECT button to clear the number in
the column and then enter the number again.
4 After entering the number in the column, select a move key (7 8 e d) located on the lower
part of the pallet by using the point buttons and press SELECT button repeatedly to move
5 tRheepereadt sfrtaempse3. to 4 for entering all the network address.
6 After finishing, select "Exit" and press SELECT button. The 10-key pallet disappears on the
screen.
10-key pallet
Exit
PJ-NET ORGANIZER
ꢀꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Notice about system construction
For installation of multiple projectors into the same network with network
unit.
Do not install multiple projectors with network units that have their default network set-
tings to the same network. The use of the network units which have the default IP address
set to the same network settings will cause IP addresses to collide and create a malfunc-
tion. When you install multiple projectors into the same network, configure the network
with the following steps.
1. Change the IP address from the default IP address. To change the IP address, use the
network setting menu on the projector. Please see item "Network configuration" for fur-
ther information (+ p.20).
2. Make sure that there is no network equipment set with the same IP address in the net-
work before connecting to the network.
3. When installing other projectors, follow the above steps to change the IP address and
connect to the network.
In case of installing the projector with network unit into the network con-
structed with the DHCP/BOOTP server.
This network unit does not support the DHCP/BOOTP server. The static IP address must be
manually configured. To use this product in this network environment, set it up so that the
DHCP/BOOTP server does not assign the IP address configured to this product for another
device on the network. Please consult your network administrator for further information.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and network configuration
[3] Installing the software
It is required to install the software into your computer to use the Network Capture func-
tion and Network Viewer function. Please install the software as follows.
Note: To install the software into the computer with Windows 2000, Windows XP
or Windows NT, you should logon as administrator. Before installation, make
sure that the other applications are closed, otherwise proper installation
cannot be made.
Network Viewer & Capture 3 installation
1 Set the supplied Network Viewer & Capture
3 CD-ROM into the CD-ROM drive of your
computer. Double click SetupTool.exe icon in
the "Tool" folder in the CD-ROM.
2 Select "English [United States]" from the
pull-down menu on the "Choose Setup
Language" window and click Ok button to
start installing and then follow the installa-
tion wizards.
As the "License Agreement" will appear, read
contents carefully and click Yes button if you
agree to the license agreement to proceed
with installing.
PJ-NET ORGANIZER
ꢀꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
Installed software
The following 3 software are installed on your computer.
● Network Capture 3:
Capture the displayed image of the computer and serve it to the projector via the net-
work.
This software is registered into "startup folder" of the computer and the capture icon
stays on the task bar after booting the computer.
● Network Viewer 3 (File Converter 1):
1
Converts to the JPEG* data format which can be projected with the projector from the
JPEG, bitmap and Power Point files.
● Network Viewer 3 (Program Editor) :
This is a tool to make the program which has a function to specify and order the pro-
jecting JPEG image data stored in the file servers.
* To uninstall these software, use "Add/Remove Program" from the control panel.
*1 This product supports the JPEG image format. This file is needed to convert to the optimized JPEG
file by using the File Converter 1 software previously. Refer to the item "Creating the available data
[Network Viewer 3]"(+p.88) about data converting for the projection.
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the software
File Converter 2 Installation
1 Set the supplied Network Viewer & Capture
3 CD-ROM into the CD-ROM drive of your
computer. Double click SetupDrv.exe icon
2 iSnetlheect"D"Erinvegrl"isfohld[UerninitethdeSCtDat-eRsO]"Mf.rom the
pull-down menu on the language selection
window and then click Install button to start
installing.
Installed software and places
Network Viewer 3 (File Converter 2) is installed in the
"Printers and Faxes" folder in the "Control Panel".
● Network Viewer 3 (File Converter 2):
This is a kind of the printer driver to convert
to the JPEG data optimized to project by the
projector from any of the documents created
by the application software.
* To uninstall Network Viewer 3(File Converter 2), just delete the "Network Viewer 3(File Converter 2)"
icon from the "Printers and faxes" folder.
PJ-NET ORGANIZER
ꢀ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Installation
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
3
Basic Setting and Operation
Describes basic operations and settings for controlling the projec-
tor by using the web browser. It is required that computer and
projector is connected to the network and the network address is
properly configured.
PJ-NET ORGANIZER
29
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Login the setting page of the projector
1 Enter the IP address
Launch the web browser installed in your
computer, enter the IP address into the
"Address" on the browser and then press
"Enter" key.
Enter the address (192.168.1.201) that you
configured in item "Network configura-
tion" (+ p.20). The default IP address is [192.168.0.2].
2 Select a display mode and login
This product provides 2 types of control mode, Standard Mode and Light Mode as the
below. Select a proper mode to match your PC and network environment by clicking
on the text link.
STANDARD MODE
For computer display, displays
graphical menus and settings. This
mode is recommended for standard
use.
LIGHT MODE
Displays with 200 x 300 dots. This
mode is optimized for use of the
handheld computer, PDA, etc. It is
also convenient if the network traf-
fic is heavy. (This mode has some
limitations on the network viewer
and multi-control functions.)
If the setting page has set the password, the
authentication window will appear. In this case type
"user" onto the User Name text area and the login
Network PIN code onto the Password text area and
then click Ok button.
* The entering User Name must be "user" and it can not be
changed.
[Note]
When accessing the projector for the first time or the
Network PIN code "0000" is set, the auto-login will be per-
formed and the next main setting page is displayed.
ꢁ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Login the setting page of the projector
3 Display of main setting page
The following main setting page will be displayed according to your display mode
selection. Perform various kinds of settings through this page. Click on the menus to dis-
play the control and setting pages.
z Main setting page in the Standard Mode display
Clock display
Display on or off by
clicking text ON or
OFF
Sub menu tab
Switches the sub
menu tab.
Page numbers
Switches the pages
by clicking the
number's tab.
Returns to Display
Mode selection
page (+ p.30)
Setting page
Main menu
For selection of control and
setting items of the projector.
Displays the control and
setting items according to
the selected menu.
✐ This Standard mode display is mainly used through this manual for the setting and
control description.
✐ If your computer does not have the
Macromedia Flash Player version 6 or later,
follow to the message on the control page
to install the Macromedia Flash Player. For
further product information or installing,
see the Adobe homepage.
http://www.adobe.com
PJ-NET ORGANIZER
ꢁ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
x Main setting page in the Light Mode display
Sub menu tab
Page numbers
Returns to the display mode selec-
tion page.
Setting page
Returns to main menu
Main menu
✐ The blank page appears if your PDA does not provide a
Macromedia Flash Player. You need to install the Macromedia
Flash Player. (+p.31)
The network viewer function in the Light mode has following limitation;
- Cannot select the program or folder for the display (+ p.97, p.99)
- Cannot check up the images in the folder or program (+ p.100).
How to use the setting page
To control and set up the projector, use the setting menus on the web browser. Describes the
basic operation and procedures commonly used on this manual.
Example of the Setting Page
The setting pallet appears when clicking the item.
Change the value by clicking ▲ or ▼ button, or type
the number onto the text box directory and then click
Set button.
* Each item has a valid setting range respectively.
Setting Pallet
✐ The value in the text box indicates current value.
✐ Each item has a valid setting range. The setting value exceeding this becomes invalid. Some con-
trol items can not be used depending on the selecting input mode or functions of the projector
you use. In this case, the values of those items are indicated with "---".
ꢁꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the setting page
Type of the setting pallet
Text box setting
Enter a number or text and
then click Set button.
or
Change a value with ▲ or ▼
button and then click Set but-
ton.
The value changes quickly
when keeping pressing ▲ or
▼ button.
Pull-down menu setting
Select an item with pull-down
menu button and then click
Set button.
or
Select an item by clicking ▲
or ▼ button.
Radio button setting
Select an item by selecting a
radio button
Check box setting
Select items by ticking on
check boxes.
PJ-NET ORGANIZER
ꢁꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Initial setting
After installing this product to the projector, perform the following basic
initial setting.
Click Initial setting on the main menu to display the initial setting page.
The model name of the projector on which this product is mounted is displayed on the
page.
Item
Description
Language..............Switches display language on the setting page.
English or Japanese.
Model name.......Indicates the model name of the projector pro-
vided with the network unit
NetworkPINcode...........Sets the Network PIN code to login the setting
page (+p.35)
PJLink.......................Switches PJLink password authentication on or off
(+p.35)
Password...............Password for PJLink function
Temperature.......Switches display temperature unit Centigrade or
Fahrenheit
!
Caution
Use of Battery
This product provides a lithium battery. When the battery runs down, the clock and timer functions
do not operate properly. Contact your local dealer for the replacement of battery. The replacement
must be carried out by a qualified service personnel.
ꢁꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Initial setting
Network PIN code setting
This is to set the Network PIN code to restrict the access from
an unauthorized person through the network.
Enter a 4-digit number as the Network PIN code onto the text
box and click Set button.
The network unit begins restarting and it takes about 20 sec-
onds. Close (Quit) the web browser and access to the login
page again in 20 seconds. This is to perform the login authentication firmly.
The default Network PIN code [0000] means no Network PIN code is set.
✐ When you connect the projector with this product to the network, it is recommended to set a
new Network PIN code. Only a four-digit number is valid for the Network PIN code.
✐ If you forget the Network PIN code to the projector, you can check it by selecting "Network PIN
code" sub menu from "Network" menu on the projector. For further information, please see item
"Network PIN code setting" (+p. 22).
PJLink and password setting
This is to set the PJLink password authentication on or off. If set
"On" with the PJLink pull-down menu, the password must be
required. Enter a password* onto the text box and click Set
button.
✐ 1 to 32 alphanumeric characters can be used for the password.
What's PJLink?
The projectors equipped with PJLink function can be used together on the same network,
regardless of model or brand, for centralized control and monitoring. This standard was
established by the Japan Business Machine and Information System Industries Association
(JBMIA).
PJ-NET ORGANIZER
ꢁꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Item
Description
Time setting........When clicking AUTO button, the date and time
set on your computer are set to the network unit
Current time.......Indicates current date and time set on the net-
work unit
Date..........................Sets date in manual
Time..........................Sets time in manual
Date and time setting
Auto setting
Click AUTO button on the page, the date and time set on your computer are set to the
network unit.
Note:
Confirm that your computer has a correct clock time before performing the auto time setting.
Manual setting
Click item Date or Time and enter date or time on the input box with adequate format.
Date is in year/month/day format.
ex. 2006/04/25
Time is in 24-hour:minute format.
ex. 18:30
ꢁꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Network configuration
Network configuration
Click Network on the main menu. The following setting page is displayed.
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server)
and projector name are set up on this Setting sub menu.
The IP address and Subnet Mask have been configured already in chapter "Installation".
If you want to change them or configure default gateway or DNS, perform them in this
page. If you change them, the network unit begins restarting and it takes about 20 sec-
onds. Close (Quit) the web browser and access to the login page again in 20 seconds.
Item
Description
IP address.............Sets IP address of the projector
Subnet mask.......Sets Subnet mask. Normally sets 255.255.255.0
1
Default gateway* .....Sets IP address of the default gateway (Router)
2
DNS* .......................Sets IP address of the DNS server. Must be set
when using the e-mail function
3
PJ name* ..............Sets name of the projector. (64 characters maxi-
mum)
✐ You must use the number specified by your administrator. The
address must be entered as a group with four numbers split by
a dot like [192.168.001.101].
*1 Set [0.0.0.0] if the network does not provide the gateway (router).
*2 Set [0.0.0.0] if you do not use the function E-Mail alert.
*3 If you use the DNS server, register the host name registered to the DNS server as a projector
name. You can access with this projector name from any computers in your network. If you do
not use the DNS server, access with the assigned IP address to the projector.
* All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.
PJ-NET ORGANIZER
ꢁ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
E-mail setting
This product has an E-mail function which can send an alert message
to users or an administrator if it detects an abnormality on the projector
or run out of the life span of the lamp. Click E-mail setting on the main
menu and follow the below steps.
Item
Description
1
SMTP server* .....Sets server name or IP address of the SMTP server
Administrator
address...................Sets e-mail address of administrator
Add e-mail
address...................Sets e-mail address of the user to send mail when
the projector has an abnormality.
1 Setting SMTP server and administrator address
1
Set the server name or IP address of the SMTP server* and administrator address. The
administrator address is set to "Reply-To" address of the message sent from the projec-
tor.
*1 The SMTP server is a server for sending E-Mail. Please contact your network administrator to
have this SMTP server address.
✐ If the network unit sends an alert message due to the abnormality on the projector but the SMTP
server is down in some other reason, the message will not be sent. In this case, the message
"Unable to connect to server." will be displayed on the setting page. To clear this message, set up
SMTP server address again.
✐ To use the E-Mail function, it must be set the DNS address on the Network setting page correctly.
✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your net-
work environment.
ꢁꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail setting
2 Registering and deleting E-mail addresses
Click "Add e-mail address" and type the e-mail address
onto the text box and click Set button. To check the
registered addresses, click Check/Delete sub menu tab.
The addresses are listed as the figure on the right.
✐ Up to 10 E-mail addresses can be registered.
Check / Delete
To delete the registered addresses, check the address you
want to delete and click Delete button.
3 Option selection for sending alert mail
Click Option sub menu tab. Check the condition items
under which alert mail will be sent and click Set button.
Please refer to item "Examples :Type and contents of alert
mail" described on the next page.
Option
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
o When PJ is turned into Standby in proper user opera-
tion.
[2]––––––––––––––––––––––––––––––––––
o When Power management function turns PJ lamp
off.
o When the signal is interrupted.
o When Auto Play is failed.
✐
If condition "When Auto Play is failed" is
checked, the trap is sent when occurring the
error during the auto display operation using
with the network viewer function (+p.98).
For further information of the error, refer to
item "Auto Display setting and control page
[3]"((+p.101).
[3]––––––––––––––––––––––––––––––––––
o When lamp Corres. Value reaches
[
] hours.
Attached message
✐The length of message should be less than 256
characters.
✐
Up to 99,999 hours can be set for use time.
PJ-NET ORGANIZER
ꢁꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the regis-
tered E-mail address according to your selected condition. Administrator or user can take
an efficient action quickly by receiving this message. This is very useful to maintain and
service the projector.
The following are examples of received messages.
● When internal PJ temperature is too high:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because internal Projector temperature is too high.
Wait for Temperature Warning Indicator turned off, and then turn the Projector on again.
If the Indicator continues flashing, check the air filter for dust accumulation.
[A] 81.5 degrees fahrenheit [B] 134 degrees fahrenheit [C] 95.6 degrees fahrenheit
Temperature of Sensor B is too high.
✐ The network unit let users know the information which thermal sensor [A], [B] or [C]
inside the projector detected the abnormal temperature risen and so the projector was
turned off. Please refer to item "Power control and status check" (+ p.46) for the location
of the sensors and each temperature . Also see the owner's manual of the projector for
further details.
● When internal PJ power circuit is failed:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because Projector power circuit failed.
Unplug the Projector from AC outlet and ask servicing to qualified service personnel.
AV,
AV,
-5V
S5V
OK
OK
OK
NG
....
Error information
PJNET, S5V
ANALOG,6V
....
....
✐ The projector lamp was turned off, because the projector power circuit failed.
Unplug the projector from AC outlet and ask servicing to a qualified service personnel with
the error information.
ꢂ0
Download from Www.Somanuals.com. All Manuals Search And Download.
E-mail setting
● When PJ lamp replacement time is reached:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The projector lamp has reached replacement time.
Lamp replacement is required.
✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is
used without resetting the lamp counter, the alert mail is sent to users in every power-
on of the projector. This alert mail will not be sent when unchecking the mail sending
condition "When PJ lamp replacement time is reached".
● When lamp corres. value reaches preselect use time:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The accumulated lamp use time hs reached 1200 hours.
Prepare for the lamp replacement.
Free messages
✐ The network unit sends a free message when the lamp use time (Corresponding value)
reaches the preselected lamp use time. It can be used for preparation of the lamp
replacement and the maintenance required.
PJ-NET ORGANIZER
ꢂ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
SNMP setting
This product provides a SNMP (Simple Network Management Protocol)
agent function. The SNMP consists of a manager and agents. The group
which communicates information each other with SNMP is called
"Community". There are two access modes in a community, Refer (read only) and Set (read-
write). This product allows to use Refer (read only) only. The SNMP message informs the pro-
jector status called "Trap" to an administrator. Click SNMP setting on the main menu and set
up each item.
PJ information
Item
Description
Contact..................Enter user name of the projector etc. (optional)
Place ........................Enter place of the projector (optional)
Community
name(refer) ........Enter community name (read only). Default name
is "public".
✐ The SNMP agent provided with this product is based upon MIB-2 defined by RFC1213. For private
MIB information, refer to file "Mibinfo/13PjNetPlus2.mib" in the CD-ROM.
ꢂꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
SNMP setting
Trap
Item
Description
Community name......Enter community name to send "Trap". Default
name is "public".
Trap address.......Enter IP address of the SNMP manager computer
to receive "Trap".
Trap check/delete
Check and delete the trap address
Checking the registered trap address and deleting the
address.
To delete the address, tick check box in front of the IP
address and click Delete button.
✐ Up to 10 trap addresses can be registered.
PJ-NET ORGANIZER
ꢂꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Basic Setting and Operation
Trap option
Trap option setting
Tick check boxes in front of the condition item to send the
trap.
✐ Click Set button if you tick or un-tick the check box on a page.
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
o When PJ is turned into Standby in proper user opera-
tion.
[2]––––––––––––––––––––––––––––––––––
o When Power management function turns PJ lamp
off.
o When the signal is interrupted.
o When Auto Play is failed.
o When lamp Corres. Value reaches
[
] hours.
✐
✐
Up to 99,999 hours can be set for the time setting.
If condition "When Auto Play is failed" is checked, the trap is sent when occurring the error during the
auto display operation using with the network viewer function (+p.98). For further information of the
error, refer to item "Auto Display setting and control page [3]"((+p.101).
ꢂꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Power control and status check
Click Power & Status on the main menu. The control page will be dis-
played.
By clicking ON or Standby button on the page, the power of the projector can be con-
trolled.
Confirmation window
as shown in the below
appears when the Standby
button is pressed.
Popup confirmation window
Item
Description
PJ status
Power .........................Displays the status of the lamp. (ON, OFF, On starting up, On cooling down)
Status ..........................Displays the status of the projector's power. (Refer to next page.)
Power control........Controls the projector power by clicking the "ON" or "Standby" button.
PJ temp.
Inside temp.A ........Displays the surrounding temperature of lamp in the projector. (Sensor A)
Inside temp.B ........Displays the surrounding temperature of panel in the projector. (Sensor B)
External temp. ......Displays the surrounding temperature of the intake vent. (Sensor C)
.........The warning icon will appear if the temperature exceeds a specified value.
Check if there is no object to obstruct the airflow around the intake or exhaust
vent. It might be airfilter clogged. Clean up the airfilter.
* The temperature unit can be set either Centigrade or Fahrenheit in item "Initial
setting". (+p.34)
ꢂꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Power control and status check
About projector condition
Status
Description
Normal............................................................... Projector is operating normally.
Power management under operation.. Power management is operating
Lamp failure................................................... Lamp failure is occurring
Abnormal temperature......................... The temperature of the projector became too high
Cooling off due to Abnormal temp. ...................... Projector detects abnormal temp. and is cooling down itself.
Power failure ................................................ Power failure has occurred inside the projector. Projector is turned
off. Disconnect the AC cord and ask servicing to a qualified ser-
vice personnel.
If the power failure occurs on the projector, "Power failure" is
indicated on the status column and the information icon appears
on the power column as shown below. Click this icon to display
further information of the power failure.
Click this icon to display
further information of
the power failure.
When a security (PIN code lock) has been set on the projector, you also cannot
control it through the network. To control the projector through the network
temporarily, execute "PJ lock suspend" command to unlock the security. "PJ lock
suspend" is on setting sub menu [3] on Setting main menu. (+p.54)
✐ The projector cannot be turned on during the projector is on cooling down.
✐ The web browser checks and updates the projector's condition every 30 seconds automatically.
PJ-NET ORGANIZER
ꢂ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Controls
Click Control on the main menu. The setting method differs depending
on the contents of the page. Click on the page number to change pages
and select desired setting items.
✐ Please see the owner's manual of the projector to have the further information
of each control item.
Input
This function is to select the input mode and source mode of the projector. Click Set but-
ton after selecting the input and source mode.
Item
Description
Input.........................Selects input mode of the projector. (1 to 4)
Source.....................Selects signal source of the input.
Input 1 : RGB(PC analog)
RGB(Scart)
RGB(PC digital)
RGB(AV HDCP)
Monitor out
Input 2 : Video
Y,Pb/Cb,Pr/Cr
RGB
Input 3 : Video
Y,Pb/Cb,Pr/Cr
S-video
Input 4 : Network
✐ The control page displays valid control items depending on the selected input mode, signal
or functions of the projector you use, therefore, there may be different controls between the
described items and actual control items on the page display. For further information , refer to the
projector's owner's manual.
✐
When the projector is in standby, only the timer on the setting menu is effective; others are inactive.
ꢂꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
System
This function is to select the system of signal input to the projector. The available system
mode are listed on the pull-down menu button according to the input signal. Select a sys-
tem and then click Set button.
Available selection when the Computer[Analog] input
Item
Description
XGA1........................It automatically switches to the proper computer
system of the input signal.
* The computer system modes (VGA, SVGA, XGA.
SXGA, UXGA, WXGA...) which meet the input sig-
nal are listed.
Available selection when the VIDEO/S-VIDEO input
Item
Description
AUTO........................It automatically switches to the proper color sys-
tem of the input signal.
* The selectable color systems are PAL, SECAM,
NTSC, NTSC4.43, PAL-M and PAL-N.
Available selection when the Y, Pb/Cb, Pr/Cr input
Item
Description
AUTO........................It automatically switches to the proper scanning
system of the input signal.
* The selectable scanning systems are 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
✐ If the mode (Mode1 to Mode 10, ExMode11 to ExMode50) which is stored in the item "PC
Adjustment" (+ p.52) is available, they are also listed together with the above mode.
PJ-NET ORGANIZER
ꢂꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Image adjustment
This function is to adjust the projected picture image and save the image mode. To store
the adjusted value, click Store button, and to load the adjusted value, click Load button.
Item
Description
Contrast.................Adjusts picture contrast (0~ 63)
Brightness............Adjusts picture brightness (0~ 63)
Color.........................Adjusts picture color saturation (0~ 63)
Tint............................Adjusts picture hue (0~ 63)
Item
Description
Color Temp..........Sets a color temperature mode. (X Low, Low, Mid, High,
Adj.)
White Balance
Red, Green,
Blue.....................Adjusts each white balance respectively. (0~ 63)
Sharpness.............Adjusts picture sharpness. (0~ 31)
* When changing the value of the white balance, the color temp.
indicates "Adj."
Item
Description
Gamma......................Adjusts brightness of darker part of the picture. (0~
15)
Noise reduction..Switches noise reduction mode (OFF, L1, L2)
Progressive ...........Switches progressive mode (ON, OFF, Film)
Reset.........................Resets the Image adjustment to previous levels.
Store.........................Stores the Image adjust-
ment values. Select an
item [Image1 - Image10]
from the pull-down menu
and click Store button.
Load..........................Loads the Image mode.
Select an image mode
from the pull-down
menu and click Load
button. There may not be
available mode depend-
ing on the input mode as
shown in the table left.
Input source
Image mode Video Computer
Standard(AV)
Cinema
Standard(PC)
Real
4
4
*
*
*
4
4
4
✐ The mark "4" means that the available image mode in the
selected input source. The error message appears when
selecting the disabled image mode indicated with "*".
*
Image1 - 10
4
ꢃ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
Sound
This function is to adjust the sound of the projector. The values in the text box represent
the current control value or status.
Item
Description
Volume...................Adjusts the sound volume from the speakers.(0 ~ 63)
Mute.........................Suppresses the sound. (ON, OFF)
Menu
This function is to control the On-screen menu of the projector. Switches menu on/off,
moves menu selection (cursor) and selection.
Item
Description
Display....................Switches the on-screen display menu on or off by
clicking ON or OFF button.
Cursor......................Moves cursor selection by clicking 7, 8, e and
d buttons and executes the selected menu item
by clicking ■ button.
PJ-NET ORGANIZER
ꢃ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
PC adjustment
Click PC Adj. on the main menu. This function is to adjust the signal from
the computer connected to the projector to obtain the proper picture
image on the screen.
Item
Description
Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA,
UXGA, WXGA, etc. or MODE1 - MODE10, EXT11 -
EXT50 which are the customized mode created by
using the "Mode Store" function described below.
EXT51 - EXT60 represents mode Totalsave1 -
Totalsave10 used in the item "Save" (+p.55).
Auto PC adj..........Performs automatic adjustment.
Fine sync...............Performs Fine Sync adjustment.(0 ~ 31)
Total dots..............Adjust the number of total dots in the horizontal
period.
Clamp.........................Adjusts the phase of the clamp. (1 ~ 255)
Display area
Horizontal..........Adjuststheimageareahorizontally.
Vertical..............Adjuststheimageareavertically.
Item
Description
Position
Horizontal.......Adjusts the horizontal position of the screen.
Vertical..............Adjusts the vertical position of the screen.
Reset.........................Resets the PC adjustments to the previous levels.
Mode Store..........Stores the PC adjustment values. Select a mode
no. [Mode1 - Mode10, ExMode11 - ExMode50]
from the pull-down menu.
Mode Free............Clear the PC adjustment values. Select a mode
no. [Mode1 - Mode10, ExMode11 - ExMode50]
from the pull-down menu.
Up to 60 characters can be used for
the Memo of ExMode11 to ExMode50.
✐ The PC adjustment settings can be stored up to 50 sets, 10 sets for Mode1 to Mode10 are stored into
ꢃꢀ
the projector and 40 sets for ExMode11 to ExMode50 are stored into the network unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the projector
Setting up the projector
Click Setting on the main menu. This function is to set up the projector.
Select the sub menu [Screen setting] or [Setting] and then set up each set-
ting.
Item
Description
Screen.....................Switches the screen mode. (Normal, Wide, True,
Full) There may not be available mode depending
on the input mode as shown in the table below.
Ceiling.....................Sets the image top/bottom and left/right
reversed. (ON, OFF)
Rear...........................Sets the image left/right reversed. (ON, OFF)
Input source
Screen mode Video Computer
Normal
Wide
True
4
4
*
4
4
4
4
Full
*
✐ The mark "4" means that the available screen mode in the
selected input source system. The error message appears
when selecting the disabled screen mode indicated with "*".
PJ-NET ORGANIZER
ꢃꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Item
Description
Logo.........................Sets on or off the logo display on the screen dur-
ing the startup. (Default, User, OFF)
Background.........Sets screen background to blue when no signal
input. (Blue, User, Black)
Display....................Switches on or off the on-screen menu display on
the screen.(OFF, CountdownOff, ON)
Freeze......................Sets the image to freeze mode.(ON, OFF)
Power
management.....Sets into the selected power management mode
(OFF, Ready, Shutdown) if the input signal is
interrupted and no control key is pressed for the
specified period of time.
*The specified time can be set 1 to 30 min.
On start..................Sets the power-on mode when connecting the
AC cord to the outlet. (ON, OFF)
Item
Description
Lamp control*...Selects lamp control mode. (Auto, Normal, Eco)
This function may be disabled depending on the
projectors.
Lamp
Corres. Value(h) Displays the lamp use time (Corresponding
value) . Reset the time after lamp replacement.
Lamp Corres. Value Reset
1. Select a Lamp-1 radio button and then click Reset button.
2. Click Ok button to execute the reset.
Item
Description
Remote control
ID.......Sets the remote control ID.(Code 1 - Code 8)
Fan speed control ........Sets the fan control speed. (Normal, Max)
Status ...............Indicates the current fan mode.
Factory default..........Sets all of the projector control items to the fac-
tory default setting except the following items.
Lamp Corres. Value, PJ time, Network PIN code,
Network setting
* This function is not effective for the settings
of the network unit, Network address settings,
e-mail settings, etc.
PJ lock suspend.............When the projector has a security of PIN code
lock, disable this function temporarily by pressing
Execute button.
Setting procedure
1. Turn off the projector , disconnect AC cord from the outlet
and then connect AC cord again.
2. Access this page with the web browser,
3. Click Execute button on the PJ lock suspend.
* This function is disabled after the projector turns on.
ꢃꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Save the controls and settings
Save the controls and settings
This page is to save and load the controls and settings of the projector in
the block. The storable items are "PC adjustment", "Control" and "Setting".
Store/free the settings
1 Click Save menu on the main menu.
2 Select a set number (Totalsave1 to Totalsave10) you intend to store current settings with
the pull-down menu button of the item Store & Free. Name this set number onto the
Memo text area.
3 *CUlicpktoS1to8 rcehabraucttteorsncaton bsetourseedthfoercthuerrMenemt soe. tting and
name into the selected set number.
To remove the saved setting, select the set number
with pull-down menu button and then click Free
button.
Select a set
number
Type a memo for
the selected set
number
✐ You can store up to 10 (Totalsave1 to Totalsave10) sets of settings into the network unit. Totalsave1
to Totalsave10 are indicated on the item "Current mode" of the PC adjustment (+p.52) as the
EXT51 to EXT60.
PJ-NET ORGANIZER
ꢃꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Check the saved items
Click Check button to check the current setting condition of the controls. Each item of "PC
adj.", "Control" and "Setting" is displayed sequentially.
Click Stop button to cancel
the auto page display.
Load a control set
S e l e c t y o u r d e s i r e d s e t n u m b e r
(Totalsave1 to Totalsave10) with the pull-
down menu button of Load Set and then
click Load button. The setting values of
the selected set number are applied to
the current settings.
Select a set
number
✐ If the contents of the saved set are not matched for the inputs equipped on the projector, the
invalid alert message may be displayed.
ꢃꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer setting
Timer setting
This page is to set the timer to turn the projector off or on at a pro-
grammed day/date and time. Follow the steps below for setting.
Click Timer on the main menu.
Present time set on the
network unit
Select date
Select day
Set execute time
Event
action
How to set the timer
1 Set a day or date
To set the timer event at same time everyday or every week,
Select day entry with radio button and then select desired day with the pull-down menu
button.
The selectable days are as follows:
- Same time everyday
- Every week ( a day from Monday to Sunday)
To set the timer event on specified date,
select date entry with radio button and then type the date with (Year/Month/Date) for-
mat.
Ex.: Type [2005/12/20] if you specify [December 20, 2005].
PJ-NET ORGANIZER
ꢃ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
2 Set an execute time
Type the time with (Hour:Minute) and 24 hours format.
Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes].
3 Select an event action
Select an event action from the pull-down menu.
Event
Action
ON..................................Turns on the projector
OFF................................Turns off the projector
Lamp Auto...............Changes lamp mode to "Auto"
Lamp Eco..................Changes lamp mode to "Eco"
Lamp Normal.........Changes lamp mode to "Normal"
*Available events depends on the projector function.
4 Register an event
Click Set button to register the set timer event. Repeat steps 1 to 4 for another timer
event setting.
Check the timer events
To check the set timer events, click Check button. The timer
events are listed. The event with blue background color rep-
resents the timer-OFF event.
Change the event mode
On the event list appearing by clicking Check button, click
on the event you want to delete, disable or enable. Click
Cancel, Delete, Timer ON or Timer OFF button on the
popup pallet.
Button
Operation
Cancel......................Cancels the setting
Delete......................Deletes the timer event
Timer OFF.............Disable the timer event temporarily
Timer ON...............Enable the timer event
ꢃꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer setting
Notes on timer setting
✐ Up to 10 timer events can be registered. Timer events always operate according to the next valid
event depending on the projector's power status. In the example below, event 3 turns on the
projector so next event 4 (also turning on projector) will not be effective because the projector
is already turned on. Similarly, when the projector is turned off by event 5, event 6 OFF will not
be effective in turning it off again. But these secondary events (event 4 and event 6) will become
effective if a person turns off the projector (after event 3 and before event 4) or turns on the pro-
jector (after event 5 and before event 6).
Invalid event
Invalid event
OFF
OFF
ON
OFF
ON
Projector Power
Event 1
Event 2
Event 3
Event 4
Event 5
Event 6
ON
OFF
ON
ON
OFF
OFF
Time
✐ When the timer events are set at the same time, the last event set will override the previous
events. For example, if there is an event like "ON at 8:00 everyday" and then new event is set like
"OFF at 8:00 everyday", only the last setting event is effective.
✐ When the timer event ON occurs during cooling down period, this is invalid event because the
projector cannot be turned on during this cooling down period.
✐ The timer operates by using the clock function provided in this product. Before setting the timer,
please confirm that the current date and time are set correctly. Timer and clock functions are
functioning using a lithium battery provided in this product. When the battery runs down, the
clock and timer functions will not operate correctly. Consult your local dealer for the replacement
of battery. The replacement must be carried out by a qualified service personnel.
PJ-NET ORGANIZER
ꢃꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Projector information
This page is to display the basic information of the projector status. Click
Information on the main menu.
Items
Description
Input.........................Displays selected input and source.
System....................Displays selected signal system.
Signal.......................Input signal status (Yes, No)
Screen.....................Displays screen mode.
Lamp status..........Displays lamp status with an animation. Refer to
the table on the next page.
Security..................Displays the security status (Yes, No)
Click this button to
update the information
ꢄ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector information
Indication of the lamp status
Icon display/background Status
Lamp on (Normal)
White-Yellow/Blue
White-Yellow/Red
Gray/Blue
Lamp on (Lamp is being used over a specified use time, replace lamp
immediately)
Lamp off (Normal)
Lamp off (Lamp is being used over a specified use time, replace lamp
immediately)
Gray/Red
Lamp failure (Lamp failure, check lamp condition)
Red/Blue with X
Red/Red with X
Lamp failure (Lamp failure and lamp is being used over a specified use
time, replace lamp immediately)
Items
Description
PJ time.....................Displays the accumulated use time of the projec-
tor.
Lamp Corres.
Value........................Displays the use time (Corresponding value) of
the lamp.
Timer........................Displays the timer setting status.
ON Timer has been set.
OFF No timer setting.
PJ-NET ORGANIZER
ꢄ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Multi-control
Controlling and setting the multi-projectors
This function enables you to control the multiple projectors equipped with
the network units that are connected to the network. Click Multi Control on the main
menu to display the control page.
Note:
To control the multiple projectors, each projector must have the same Network PIN code.
Example of multi control
PJ1
PJ2
PJ3
PJ4
PC6
PC5
PC4
Select Input2 for
PJ1 to PJ4.
ꢄꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
Start/stop the multi control
To start or stop controlling the multi-projectors, click
Multi control setting menu and select ON or OFF.
Switches on and off the
multi-control function
Multi control setting
OFF........Stops multi control function
ON..........Starts multi control function. The multi control
menu will appear when setting ON. These
items of menu are linked to the main menu.
The multi controllable menus are "Power & Status", "PC
adjustment", "Control", "Setting", "E-mail setting", "Timer",
"SNMP setting" and "Network Viewer". Click each menu
and perform setting and adjustment.
✐ The word "MULTI CONTROL" appears on the each control
page during the multi control is operating.
This shows the multi con-
trol is operating now.
PJ-NET ORGANIZER
ꢄꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Register the projector
To use the multi control function, register the IP address of the projector you intend to
control. Click PJ registration sub menu tab and set the IP address, Memo and Multi control
item, then click Set button.
Items
Description
IP address.............Enter IP address of the projector to control
Memo......................Enter projector name or installed location etc.
Multi control item
Control.............. Controlling the projector
Control & Image.... Controlling and displaying images
Image................. Displaying the images
Confirmation of registered projector
To check the registered information, click Conf. & Change
sub menu tab. The registered information of the projector is
listed as the below.
* When you click on a listed IP
address, the login page for the
selected projector will be dis-
played with a new window.
* The word "none" is displayed if not using the "Memo" func-
tion.
IP address
Status
Memo
Page no.
Click here to close
the sub menu Conf.
& Change.
✐ 10 projectors per a page can be registered and up to 100 sets can be registered for the multi-
control.
ꢄꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
Change the mode of the registered projector
To change the mode of the registered projector, select a mode with the pull-down menu
button under the IP address of the target projector and then click Set button.
Mode
Operation
Control.................... Controlling the projector
Control & Image ......... Controlling and displaying images
Image ...................... Displaying the images
OFF............................ Excluding from the multi-control
Delete...................... Deleting from the multi-control
* The multi control item is not changed during using the
network viewer function. It is not available with the light
mode.
Status
If some of the registered projectors are disabled by
some reasons (such as disconnecting the power source,
disconnecting the LAN cable, disconnecting from the
network), control changes will continue to be effective
for the projectors that are still active. At the same time,
the deactivated projectors are excluded from the multi-
control. The status of the registered projectors are indi-
cated under the projector name. See the table below
for status indications.
Status
Status
Description
(blank).....................The projector is connected to the network correctly
No connect..........The projector may not be connected to the network. Please check the connection
and network configuration of this projector.
PIN code error.............The PIN code is incorrect. The PIN code for the multi-controlled projectors must be
the same. Change the PIN code of this projector to the common PIN code.
File Error................. Not displaying the images. Check if this projector is using the Network Capture
function or Network Viewer function individually, or in the standby mode.
* The network unit updates the status at the time when the multi-control function was executed.
✐ If the multi-controlled projector is in the standby mode, any change is not effective except timer
setting.
✐ Cannot register, delete or change the multi-control setting during using the network viewer func-
tion.
✐ It is recommended that a specified projector should be chosen for setting as a master when you
use this multi-control function. The control for the multi-controlled projectors will become too
complicated operation if this function is used for each projector.
✐ If the registered projector is not connected to the network, it will take some time to complete the
multi-control operation because of waiting for the response from each registered projector.
✐ There are some disabled items in the multi-control function for the light mode.
PJ-NET ORGANIZER
ꢄꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
Conf. & Change page in the light mode
Following functions in the "Conf. & Change" page are
not available in the light mode.
- Changing the control mode.
- Deleting the registered IP address
- Indicating the each status
- Indicating the each memo
This indicates that the
mode is "VisualControl".
This indicates that the
mode is "Control".
(Conf.&Change page in the light mode)
Controlling all together
"Power & Status", "PC adjustment", "Control" and "Setting"
can be controlled all together. Set "ON" the multi control
setting and adjust controls of each menu. The setting
value is applied to the registered projectors sequentially .
✐ This is effective only if the multi control item of the registered
projector sets to either "Control&Image" or "Control".
Setting all together
"E-mail setting", "SNMP setting" and "Timer" can be set all
together. Set "ON" the multi control setting and items of
each menu. The setting value is applied to the registered
projectors sequentially.
✐ This is effective only if the multi control item of the registered
projector sets to either "Control&Image" or "Control".
ꢄꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Multi-control
Viewer auto setting all together
"Viewer auto display" can be set all together. Set "ON" the
multi control setting and select [3] Auto display setting
from Viewer sub menu. Set the display time periods and
repeat times for the auto image display. When clicking
Start button, the registered projectors start playing back
the auto image display in sequential.
✐ For further information of the Auto display, see "Using the net-
work viewer function". (+p.98)
✐ This is effective only if the multi control item of the registered
projector sets to either "Control&Image" or "Image".
PJ-NET ORGANIZER
ꢄ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Controlling the Projector
ꢄꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
About Network Capture function
The Network Capture is a function to project the screen images of the computer which
has a Network Capture 3 software by the projector through the network. This function has
2 kinds of mode as the below.
- Real Time Capture (+p.ꢀ2)
A function to display the screen image of the computer by the projector through the
network in real time.
- Network Communication (+p.ꢀꢀ)
This mode is to communicate by sharing the capture image of a computer with multiple
computers and a projector. User can draw the text and figure on the captured image by
using a drawing tool.
✐ Up to 30 computers can be registered.
✐ The Network Capture function cannot be used when using the Network Viewer function. The
Real Time Capture and Network Communication mode cannot be used at the same time.
Launching the Network Capture 3
After installing the Network Capture 3 software, the shortcut icon is copied into the
"Startup" folder. When you boot the computer, the Network Capture software also starts
and its icon stays on the task bar. If the icon is not appeared on the task bar, the Network
Capture 3 software is not starting. Click "Network Capture 3" from "Start" - "All the
Programs" - "Network Viewer & Capture 3" menu to launch it manually. The status which
the Network Capture 3 icon stays on the task bar is just preparing the screen capturing.
Commands on the task bar
When clicking the Network Viewer & Capture 3 icon
on the task bar, The popup menu will appear as the
right. See the next page for each operation.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
About Network Capture function
Items
Description
Start real time capture..................Starts the real time capturing. (+p.72) The screen image of the computer is
projected on the screen in real time.
Start communication ....................Starts the Network Communication. (+p.77) Captured image is projected
on the screen. The captured image edit window appears on the computer
screen.
Parameter set up............................Sets the communication parameter between the computer and network
unit of the projector. For further information, see item "Parameter set up"
below. (+p.71)
Version information.......................Displays the version of this software.
Shut down ......................................Quits the application.
Parameter set up
1 Click Network Capture 3 icon on the task bar.
2 Click "Parameter set up" on the popup menu. The set-
ting window will appear.
3 Set Capture Port and PIN code to match to the pro-
jector’s port number and Network PIN code.
✐ To check the Capture Port number, see item "Control by
the web browser" (+ p.74). To check the PIN code, see
item "Network PIN code setting" (+ p.22).
✐ Specify the port number of TCP/IP. The default port
setting is 9000. There are some reserved port numbers
and also some applications may use their own port
numbers. If one of those port numbers is used, the alert
dialog window will appear and let you know that it is an
invalid port number. In this case, use another port num-
ber.
✐ The reserved port numbers are http (80), ftp (21), telnet
(23), etc. The port no. 4352, 10000, 10001 are reserved to
control the projector through the LAN port.
4 Click Search button to list up the available IP address
assigned to the projector and select desired IP address you use, or you can enter the IP
address or host name manually if you know that IP address or host name.
✐ It may not find any address over the router. Consult your network administrator for further
details.
5 Set the quality of the image.
Quality: Selects from High, Mid, Low
Image Scaling: If checked, the screen image size of the computer is automatically adjusted to the
projector’s screen size.
6 Set capture start time in second unit.
✐ This is effective in the communication mode only. It sets up the time period from executing
the command "Capture transfer" to capturing and transferring the actual screen image. 0 to 60
seconds can be set.
7 Click Ok button to close the setting window.
About Image Quality
Quality : Quality mode of the captured image shows following JPEG compression mode.;
High
Medium : JPEG medium compression mode
Low : JPEG high compression mode
: JPEG low compression mode
PJ-NET ORGANIZER
71
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Using the Real Time Capture
This is a function to project the screen image of the computer by the projector in real time.
The captured image projected by the projector can be selected from the computer, web
browser and the projector respectively.
Registering the computers
Up to 30 computers can be registered.
1 Access to the control page of the projector by using the
web browser. From the Network menu, click Capture
2 tSawbittcohditsoplCayonthneescettitoinngspeatgtein(g+ppa.3g7e). by clicking the
page number tab [3]. Enter the IP address of the com-
puter to the PC number, and then click Set button. Click
Set button to register the IP address for each page.
✐ The registered computer enables to start capturing if only the Network Capture icon appears on
the task bar.
✐ The transfer speed of the captured image using the Real Time Capture function is depending
on the network environment and data volume of the image. For example, when transferring an
image (Computer resolutions and colors: XGA, full color, Picture quality: High), the transfer speed is
about 2 pages per second in maximum. It cannot be supported for movie pictures.
7ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Real Time Capture
[1] Control by the computer
* PC provides the Network Capture.
PJ2
Project this screen
image with PJ2.
PJ1
PC1
Capture
* Start capturing from
the PC1.
PC3
PC4
PC6
PC5
Select input mode to "Network" previously.
1 Click Network Capture 3 icon on the task bar.
2 Click Start real time capture on the popup menu.
The screen image of the computer will appear on the
projected screen in real time.
• To stop capturing, click Stop real time capture on
the popup menu. The captured image of the com-
puter on the screen is frozen.
Icon on the task bar
• To restart capturing, click Restart real time capture
on the popup menu.
3 To end capturing, click End real time capture on the
popup menu.
Standby
Capturing
If the Network PIN code set on the projector dif-
fers from PIN code set on the parameter setting
up, The Pin code setting window appears. Enter a
correct PIN code and click Ok button.
✐ If the error message appears, check item "Parameter set up" (+ p.71).
PJ-NET ORGANIZER
7ꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
[2] Control by the web browser
* PC provides the Network Capture.
PJ2
PJ1
PC1
PC2
Capture
* Start capturing of
the PC1 from the
PC5.
PC3
PC4
PC6
PC5
Project a screen
image of PC1 with
PC2.
Select input mode to "Network" previously.
1 Access to the control page of the projector by using
the web browser. From the Network menu, click
2 SCealpetcutrethteabctoomdpispultaeyrtnhuemsebtteinrgfrpoamget(h+e pp.u37ll)-.down
menu button of "Connecting PC" and click Start but-
ton. The screen image of the selected computer will
appear on the projected screen in real time.
• To stop capturing, click Stop button. The captured
image of the computer on the screen is frozen.
3 •ToToernedstcaarpt tcuarpintugr,inclgic,kclEicnkdRbeustttaornt.button.
Set "On" when
using the wireless
mouse function
✐ The IP address of the connecting PC should be registered previously (+ p.72).
✐ If the error message appears, check item "Parameter set up" (+ p.71).
✐ You can use the capture function by using the web browser or the projector if the Network
Capture 3 software is installed into the computer correctly and its icon stays on the task bar.
7ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Real Time Capture
[3] Control by the projector
Project a screen
image of PC1 with
PC2.
* PC provides the Network Capture.
PJ2
PJ1
PC1
PC2
Capture
* Start capturing of
the PC1 from the
projector PJ2.
PC3
PC4
PC6
PC5
Select input mode to "Network" previously.
1 Select "Network Capture" icon from "Network" menu. Press SELECT button on the pro-
2 SjeecletocrttPwCicneutmobdeisrptloaycothnenencettw. ork capture setting pallet.
3 Select "Connect" and then press SELECT button to start capturing. The screen image of
4 tThoeesnedleccatpedtucrionmg,psuetleecr tw"iDlliascpopnenaer cotn" athnedpthroejnecptreedssscSrEeLeEnCinT rbeuatlttoimn.e.
Set "On" when
using the wireless
mouse function
✐ The IP address of the connecting PC should be registered previously (+ p.72).
✐ If the error message appears, check item "Parameter set up" (+ p.71).
✐ Selectable computer from the projector is PC1 to PC10. Other PCs cannot be selected from the
projector.
✐ The projector does not provide the function to register the IP address of the computer and to set
the parameter of the capturing. They should be registered by using the web browser previously
(+ p.71-72).
PJ-NET ORGANIZER
7ꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Advanced using example
Displays the presentation data stored in the computer by using the wireless mouse
function from the projector.
1 Start capturing of the computer PC1 by using the projector.
Select “Network Capture” icon from the menu and select "PC1" and then select "Connect" (+
p.75).
2 =O>nTthheeNPetCw1ocrkaCpatputruereimsoaftgwearperionjsetacltleeddinonthethseelescctreedecno,msepaurtcerhwaillpstraerstecnaptatutiroinng.file data
stored in the PC1 by using the wireless mouse function of the remote control supplied
3 wSeitlehctthaedpersoijreecdtofirle. and double click with the remote control .
=> The application by which the document was created starts and the projector projects the pre-
sentation picture on the screen.
4 Start the presentation.
=> By using wireless mouse function, control the page browsing and some other operations for
the PC1.
✐ For further instructions of the wireless mouse, please refer to the projector’s owners manual.
✐ On the projected screen using with the network viewer, the shape of the mouse pointer differs
from the one on the computer’s screen.
Project a screen
image of PC1 with
PC2.
* PC provides the Network Capture.
PJ2
PC1
PC2
PC4
Capture
PC3
* Controls PC1 with wireless mouse.
PC5
Setting condition
Projector
Input mode: Network
Network Unit
Registering the connection: The IP address of the computer and proper parameter
must be set to the PC1 (+ p.71-72).
Mouse Display: "On" (+ p.74, p.75)
Computer PC1
Software: The Network Capture software is installed correctly and its icon appears on
the task bar.
7ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Communication
Using the Network Communication
This Network Communication is to communicate by sharing the captured image of a com-
puter with multiple computers and a projector. User can draw the text and figure on the
captured image by using a drawing tool.
The data has the captured image of a Main PC and communication information is sent to
the projector. The projector projects this data onto the screen and serves this data to other
computers (Sub PC) at the same time. The Sub PC receives served capture data and display
it on the screen. The Main PC and Sub PC also can edit the captured image by using the
drawing tool. This edited image is applied to all the computers automatically.
PJ1
Capture
PC6
PC1
PC2
PC5
Capture a screen
image of PC5 and
make marking with
a tool.
* The Main PC is a computer which started using of communication function, and serves
own computer screen captured image to the Sub PC. The Main PC has an authority to
quit using whole of communication. To become the Main PC, execute the command
"Start Communication" or "Capture transfer". For further information, see item "How to
use the Network Communication". (+p.81)
* The Sub PC is a computer which receives a captured image from the Main PC. On the
communication mode, the Sub PC can become the Main PC anytime.
PJ-NET ORGANIZER
77
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Settings before using the Network Communication
To use the Network Communication, the capture setting of the network should be set
either [1] or [2] described below.
[1] Setting the network unit searches all the available target computers in the net-
work automatically.
or
[2] Setting the target computers are registered to the network unit.
Perform capture setting following to the description below.
[1] When serving the capture data to all the tar-
get computers in the network.
By using the web browser, display "Communication set-
ting" from menu "Network"-"Capture"-"Page 2". Confirm
that the item Auto search target PC is "ON". If "OFF",
change mode to "ON".
* Network unit can find up to 30 computers in the network.
[2] When serving the capture data to the specific
target computers in the network.
Set item Auto search target PC is "OFF" described in
the above and then display "Connection setting" from
menu "Network"-"Capture"-"Page 3" with the web
browser. Enter the IP address of target computer and
click Set button to register.
* Up to 30 computers can be registered to the network unit.
✐ To display the served capture data, the computer needs to operate the software Network Capture 3.
7ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Communication
Description of capture editing window
Select menu "Start Communication" from the popup menu appearing by clicking the
Network Capture 3 icon on the task bar. The capture editing window will appear on the
computer screen as the below. For basic operation of each menu, refer to the item "Menu
tree" below.
Menu
Tool bar
Capture Image
Authority status
indication frame
(+p.81)
Menu tree
Menu
File
Submenu
Operation
Save Communication
Saves a captured editing image as the data(JPEG)
Save dialog window appears
Quit the communication mode
Close the Editing window
* main pc only
End Communication
End Editing
* sub pc only
Control
Edit
Capture transfer
Authority
Captures a screen image and sends it to the network unit
Acquire/release the authority to edit the capture image
Selects a pencil tool
Tool
Pencil
Eraser
Selects an eraser tool
Letter frame
Free
Straight line
Square
Selects a letter frame tool
Draws line with freehand
Draws straight line
Draws square
Form
(Shape)
Oval
Draws oval
Square(Painting out) Draws filled square
Oval(Painting out) Draws filled oval
Attribute
Delete all
Undo
Appears a attribute window
Delete all the drawings on the image
Cancel the last executed operation
Display
Help
Full screen
Tool bar
Switches capture editing window, normal or full screen
Switches standard tool buttons on or off
Switches form(Shape) tool buttons on or off
Switches color tool buttons on r off
Switches attribute tool buttons on or off
Keeps capture editing window on foreground always
Displays software version number
Standard
Form(shape)
Color
Attribute
Display on foreground
Version information
PJ-NET ORGANIZER
7ꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Tool bar button names
The following commands are assigned to the tool bar buttons. For each operation, refer to
the description of item "Menu tree".
Command Tool
Bar of Main PC communication
Save
End communication
Capture
transfer
Authority
Attribute
Standard
tool bar
Form
tool bar
Oval(Painting out)
Square(Painting out)
Pencil
Letter
frame
Straight line
Eraser
Free
Oval
Square
Command Tool
Bar of Sub PC
End Editing
Color pallet 16 colors
Color tool
bar
Attribute
tool bar
Width (Large,
Medium, Small)
Translucence
✐
To switch the tool bars displaying on or off, select each command from menu "Display"-"Tool bar".
✐ User can realign and join the tool bars (Standard, Shape, Color, Attribute), and change it to the
floating pallet by taking a drag and drop of the tool bars.
✐ There are some disable buttons depending on the tools and authority mode. In this case the but-
ton indicates with gray.
ꢅ0
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Network Communication
How to use the Network Communication
Start the communication
1 Display an image on the computer screen.
2 Select Start Communication from the popup menu appeared
by clicking Network Capture 3 icon on the task bar.
The capture editing window with a captured image appears
on the computer screen.
✐ If an error message appears, check item "Parameter set up". (+p.71)
Icon on the task bar
✐ The icon on the task bar is activated during the network communica-
tion operates.
Standby Communication
Join the communication (only for Sub PC)
1 Network Capture 3 icon is activated to inform users in the net-
work that the Network Communication is operating. Display
2 Stheelepcot pSutaprmt eedniutibnygcmlicekninug. its icon.
The capture editing window with
a captured image appears on the computer screen.
Exit from the communication (only for Sub PC)
Click "
:End editing" button on the standard tool bar. The capture editing window will be
closed.
✐ This command is available with the Sub PC only.
✐ When executing "End editing" with the authority provided, the authority will be released.
End the communication
Click " :End communication" button on the standard tool bar.
The capture editing window will be closed.
✐ This command is available with the Main PC only.
✐ It cannot be ended the communication while other PC has the authority. To end communica-
tion forcibly, click the Capture 3 icon on the task bar and select "Shut down" on the popup
menu.
Acquire and release of editing authority
To edit the capture image, each computer needs to acquire the authority respectively. To
acquire the authority, click " : Authority" button on the standard tool bar and then edit
the capture image. The capture editing window indicates the authority status by changing
the frame color according to the current authority mode as follows.
Red
Blue
ready to acquire an authority
PJ-NET ORGANIZER
Green
other computer having
an authority
having an authority
ꢅ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Edit capture image
Drawing figures
1 Click " :Pencil" button on the form tool bar.
2 Select its attribute (shape, width, color and translucence) from the form and attribute
3 tDoroalgbaarm. ouse pointer on the screen image to draw the figure.
Erase drawn object
1 Click " :Eraser" button on the form tool bar.
2 Select its attribute (shape, width) from the form and attribute tool bar.
3 Drag a mouse pointer on the screen image to erase the figure.
Hints of the drawing
✐ Straight line tool............ To draw the vertical line or horizontal line, drag a mouse pointer with shift
key pressed.
✐ Square tool........................ To draw the quadrate rectangle, drag a mouse pointer with shift key
pressed.
✐ Oval tool............................. To draw the perfect circle, drag a mouse pointer with shift key pressed.
✐ To cancel the drawing, select command "Edit"-"Undo" from the menu.
✐ To erase all the drawing at once, select command "Edit"-"Delete all" from the menu.
✐ The popup menu appeared by right clicking of the mouse is also available to select the tool and
change the attribute.
Setting of the drawing tool attribute
When clicking " :Attribute" button on the standard tool bar, the following window will
appear. This window appears only if the pencil or eraser tool is selected.
Line width
Large: 8 dots
Medium: 4 dots
Small: 2 dots
Select a color on the
color pallet appeared
by clicking here.
Sets translucent
color
ꢅꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Network Communication
Drawing letter
1 Click " :Letter frame" button on the form
2 tSoeolelcbtaar.color of text with color tool bar.
3 Drag a mouse pointer on the screen image to
specify the area of the letter frame. The letter
4 Einnpteurt tdhiaelolegttwerinodnotowthweillwaipnpdeoawr..
To change the letter attribute, click Letter
attribute button. See item "letter attribute
5 sCeltitcinkgO" bkeblouwt.ton to fix the content. The
entered letter appears on the captured image.
✐ If the entered letter overflows the area of letter frame, the letter frame is automatically extended
downward.
✐ Up to 1000 characters can be used for a letter frame. The maximum size of the letter frame is 100
characters a row and 15 rows.
Letter attribute setting
The font attribute setting window appears when clicking " :Attribute" button on the
standard tool bar with the letter frame tool selected, or clicking Letter attribute button
on the letter input dialog window described the above.
Sets type face, style, size and
effects of the font
Predefined 16 col-
ors are available.
Sets translucent
color
PJ-NET ORGANIZER
ꢅꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Network Communication operation and change of state
Network Communication can be used under the environment which one or more com-
puters are connected to the projector via the network.
Preparation
Launch the Network Capture 3 software on the target computer (+p.70). Set the projector
in the standby or turning on. Check IP address of the target computer is registered in the
connection list (+p.78).
Operation on the Main PC
Operation on the Sub PC
➔ The icon on the task bar is activated to
let users know that the captured image is
now serving.
z Executing the command "Start Editing".
➔ The capture image on the Main PC
appears on the screen.
Frame
Frame
z
Executing the command "Start Communication".
➔ The capture editing window appears on the
screen. The icon on the task bar is activated.
R
B
x
Editing the capture image using with the tools.
➔ The editing information on the Main PC is
➔ The editing information is automatically
R
G
B
B
G
R
reflected on the Sub PC.
transferred to the Sub PC.
c Releasing the editing authority.
➔ The color of authority status frame changes green.
➔ The color of authority status frame chang-
es green.
x Acquiring the authority.
➔ The color of authority status frame chang-
es red.
➔ The color of authority status frame changes blue.
c Editing the captured image using with the
➔ The editing information on the Sub PC is
reflected on the Main PC.
tools.
B
R
➔ The editing information is automatically
transferred to the target PC.
v Releasing the editing authority.
➔ The color of authority status frame chang-
es green.
➔ The color of authority status frame changes green.
G
R
G
B
v Acquiring the authority.
➔ The color of authority status frame changes red.
➔ The color of authority status frame chang-
es blue.
b Repeat steps x, c if required.
b Repeat steps x to v if required.
n Executing the command "Capture transfer".
➔ Updating the editing window with a new
captured screen image.
➔ A new captured screen image appears on
R
R
B
the editing window.
m Repeat steps x to b.
, Ending the communication.
➔ The capture editing window disappears.
➔ The capture editing window disappears.
✐ The projector projects the edited captured image on the screen when the input mode of the pro-
jector is set "Network".
✐ The command "Save Communication" can execute in any of the mode even if not having the
authority.
✐ The arrow (➔) shows a response to the command executed.
✐ The execution of the command "End Communication" or "End Editing" on the Sub PC has no
effect on the other target computers.
ꢅꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Executing the forcing mode
Executing the forcing mode
The network capture setting of the web page provides a forcing executing command. This
command executes the release of authority or ending the communication forcibly. This is
useful when the other target PC keeps an authority all the time, or when the condition of
the communication is not stable.
Click page 2 Communication setting from the menu "Network"-"Capture". Execute com-
mand by clicking the button Free, Quit or Update.
Displays IP address of the Main PC
Displays IP address of the computer
has a editing authority
Item
Free...........................Releases the editing authority forcibly
➔ Sets condition which all the users can acquire an authority
Quit...........................Quits the communication forcibly
➔ The capture editing window on all the computers closes forcibly.
Update....................Acquires the latest communication status
➔ Updates the IP address of the Main PC and Update authorized PC.
Description
PJ-NET ORGANIZER
ꢅꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Network Capture
Error information
Error messages
Cause and corresponding
Error when executing the communication. The parameter setting
(host name, capture port) has not been set.
➔ Check parameter setting (+p.71)
Set up the parameter.
Error when executing Start Communication or Start real time cap-
ture. The IP address of the computer has not been registered.
➔ Register the IP address by using the web browser (+p.78)
It has not been registered to PJ
as a group.
Error when executing Start Communication or Start real time cap-
ture. The other capture, viewer or advanced card imager function
is now operating.
Cannot be displayed as PJ is
under display.
➔ Wait until the communication function is available.
Cannot establish the connection with the network unit when
executing the Start communication, End communication, Capture
transfer, Start real time capture or End real time capture.
Cannot connect to PJ.
➔ Check connection of the network cable.
Cannot transfer the data to the network unit when executing the
Start Communication, End Communication, Capture transfer, Start
real time capture or End real time capture. The time out period is
10 seconds.
Cannot transfer data to PJ.
➔ Check connection of the network cable.
Cannot receive the data from the network unit when executing
the Start Communication, End Communication, Capture transfer,
Start real time capture or End real time capture. The time out
period is 10 seconds.
Cannot receive data from PJ.
➔ Check connection of the network cable.
Other PC has authority.
Cannot complete "Network
Communication".
When executing the End communication, you cannot quit the
communication because other computer has an authority
Other PC has authority. Cannot
obtain authority.
Other computer has an authority.
When setting the parameter, the computer cannot find the set-
ting host name or IP address in the network.
➔ Use available host name or IP address.
The server name or address
could not be resolved.
When setting the parameter, the reserved port number is speci-
fied.
➔ Check parameter setting (+p.71)
Invalid port number
PJ has not started Network
Communication. Close the window
and open it again.
The projector might have turned off during the communication.
➔ Check projector power and restart executing "Start communica-
tion".
ꢅꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
6
Network Viewer
Network Viewer is a function to display the image data stored in
the file servers by the projector through the network.
Describes about file converter software File Converter 1, File
Converter 2 and program creator software Program Editor, and
how to use Network Viewer.
PJ-NET ORGANIZER
8ꢀ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
Creating the available data [Network Viewer 3]
The image available with this projector is the JPEG format (.jpg). There are several types of
JPEG data. Before using the images with the Network Viewer function, it should be con-
verted to the optimized JPEG data for this projector.
[1] How to use the Network Viewer 3 (File Converter 1)
The File Converter 1 is a software to convert from the JPEG, bitmap or Power Point data to
the optimized JPEG data for the projector.
Launch and quit the File
Converter 1
To launch the File Converter 1, click
"Network Viewer 3 (File Converter 1)"
menu from "Start" - "All Programs" -
"Network Viewer & Capture 3" menu.
To quit the File Converter 1, click
on the close box on the upper
right hand of the window.
File Converter 1 window
Menu
Command
Tool Button
Preview window
Explorer window
to browse image
files
ꢅꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating the available data [Network Viewer 3]
Menu Tree
Menu
Sub Menu
Description
View
Update
Preview size
Option
Convert a folder
Convert each file
Version information
Updates contents of the preview window
Sets size of the preview image, Large, Middle, Small
Sets default of the output destination and conversion mode
Converts files in a folder into JPEG files at once.
Converts a file into a JPEG file individually
Tools
Conversion
Help
Displays the version information
Command Tool Button
Convert
each file
Convert a
folder
Update
Create the available data
1 Select a folder in which the image files are stored by the explorer window.
The preview images of the available image data (JPEG file, Bitmap file, power point file)
in the selected folder are displayed on the preview window.
✐ On the preview window, the preview displayed with the red frame represents a file not opti-
mized JPEG file or Bitmap file for the projection. The preview without the red frame represents
the optimized JPEG file for the projection. So you do not need to convert them again, but if you
change the size or image quality, perform to convert them again.
Preview with red
frame represents the
file not optimized for
the projection.
Preview of the Power
Point data
PJ-NET ORGANIZER
ꢅꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
2 When converting each file, select a preview
image first and then click Convert each file.
✐ To select two or more files at once, press and hold
"Shift" key or "Ctrl" key and then click the preview images.
When converting all the files in a folder, select a folder and click Convert a folder.
3 As the confirmation window appears, check the conversion object and conversion
type and then click Ok button. The File converter 1 starts converting and stores the
optimized files into the output folder. It is enable you to select a local hard disk of your
computer, shared computer in the network, a directory of the FTP server. To change the
conversion type or output destination, click Change button.
✐ If the power point file is included in the conversion object, the Microsoft Power Point software
will be launched and start converting automatically.
Dialog window when using "Convert
each file" and "Convert a folder"
✐ To convert images from the power point file, Microsoft Power Point software is required in your
computer.
✐ In the power point file conversion, all the pages are converted into JPEG files separately.
ꢆ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating the available data [Network Viewer 3]
Setting of output destination and conversion mode
When clicking Change button on the confirma-
tion window in the step 3 on the previous page,
following option setting window appears.
Output destination
Select either Folder or FTP server as the output
destination of the converted files.
Folder
Output folder.....Specify a folder in the local hard disk
or shared computer in the network
FTP server
Host name............Enter host name or IP address of the
FTP server
Root Folder..........Specify the root directory of the FTP
server. Normally use "/".
User ID ....................Enter your login account of the FTP
sever.
Password...............Enter your password of the FTP server.
Output folder.....Specify a directory of the FTP server.
Conversion mode
Resolution............Selects output image resolution (VGA to SXGA+)
✐
The image resolution higher than the projector's panel resolution cannot be dis-
played.
Image rotation.....Selects image rotation (0, 90, 180, 270).
Conversion Type
Fit............................. Converts as either width or height of
the image sets to be the maximum
screen width or height.
Justify
[both ends]............... Converts as width of the image sets
to be the maximum screen width.
Justify
[top and bottom]..... Converts as height of the image sets
to be the maximum screen height.
Cut........................... Cuts image with the screen size not depending on the image size. This type has fol-
lowing mode.
✐ Select this mode when you want to have the images with the original size. Select
each mode by clicking on the button.
Image Quality....Selects an image conversion quality with "High", "Mid" or "Low".
PJ-NET ORGANIZER
ꢆ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
[2] How to use the Network Viewer 3 (File Converter 2)
The File Converter 2 is a kind of the printer driver software to convert to the optimized
JPEG data for the projection from the any documents created by the other software such
as text editor, spreadsheet or presentation software. It is possible to convert to the JPEG
file from the any kinds of documents created by the software which has a "print" menu.
Create the available data
1 Open a document with the individual software.
2 Select a "Print" sub menu and open the printing dialog. On the window, select "Network
Viewer 3 (File Converter 2)" icon on "Select Printer" item and click Print button.
✐ Set the option setting for the page layout
or paper setting by clicking Preferences
button if required.
3 Select a folder and click Save button.
✐ The file name is named with "Image001" as
the default. If the converted image has 2 or
more pages, the file names are numbered
from "001" to "999" in a sequential order.
✐
Image quality and Conversion type can be
setup on this window. For further informa-
tion, please see "Setting of the Conversion
Mode" (+ p.91).
✐ It may appear the white space around the
edges on the converted image depending
on the type of the image data.
✐ The above procedure may differ from each computer environment and applications.
ꢆꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a program file [Program Editor]
Creating a program file [Program Editor]
Network Viewer 3 (Program Editor) is a tool to make a program file which specifies the dis-
play order of the image and its file path in the file server (FTP server). The Program Editor
makes a folder "DispParam" at the login root directory in the FTP server and makes files as
each program name into this folder. These files are called "Program". By specifying the pro-
gram file with the Network Viewer function, you can have the programmed display with
the projector .
Procedure of making program
1 To launch the Program Editor, click "Network Viewer 3
(Program Editor)" menu from "Start" - "All Programs" -
"Network Viewer & Capture 3" menu.
2Click Connect button.
3If the connection setting window appears, enter the each
item and then click Ok button.
The setting window disappears and then the programs
are listed on the window if there are program files at
the login directory in the connected FTP server.
Item
Description
Host name............Enter the FTP server name or IP address
Root Folder .................Specify the root directory of the FTP server. Normally use "/".
User ID ....................Enter your login account of the FTP sever or use blank when you login as anonymous
account for the FTP server
Password...............Enter your password (PIN code) or use blank when you login as anonymous account.
IMPORTANT
It is required to set the write permission mode for the login directory of the FTP server.
If only the read only mode, you will have an error when you register a new program.
PJ-NET ORGANIZER
ꢆꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
4 Click New button.
5 Enter a program name and click Add button.
Change : Changes the contents of
the program file.
Remove : Removes the program from
6 The folder selection window appears and select a
folder in which the JPEG data are stored and then
click Add button to register into the folder lists.
the list.
Add....................Displays the folder selection window.
Delete..............Deletes the folder path from the folder list.
UP.......................Moves up the selected folder path.
DOWN .............Moves down the selected folder path.
Edit.....................Used to set up the display order or display time of the image individually. For further
information see item "Setting up the display order and time of the images" on the
next page.
✐ The order of the display is listed in the folder list window. To change the order of the display,
change the list order of the folder list by using UP or DOWN button.
✐ The programs are stored into the "DispParam" folder at the login root directory and this
"DispParam" folder is made by software automatically.
7 Click Register button to register the folder list into the program.
8 Click Close button to quit the Program Editor.
ꢆꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a program file [Program Editor]
Setting up the display order and time of the images
In the default setting, the display order of the images is ASCII code order of the file name.
To change the display order or to set up the display time, take the following procedure.
Display the folder list window in step 6 of the previous page.
1 Select a folder list contains images to change.
2 Click Edit button. The images in the selected folder are displayed with the file name on
the index window.
When selecting "Image" from "View" menu,
the thumbnail of the image will be displayed
(default setting). When selecting "Icon", the
icon image will be displayed.
✐ It takes a time to display thumbnails.
✐ The number in front of the file name indicates
the display order of the image.
Display order
number
File name
Menu
Sub menu
Description
File
Edit
Exit................................Closes index window
UP..................................Steps up the display order of the selected images
DOWN........................Steps down the display order of the selected images
Display time...........Sets up the display time of the selected images
Image.........................Displays thumbnail of the images
View
Icon..............................Displays images as the fixed icons
Update.......................Updates images information on the index window
PJ-NET ORGANIZER
ꢆꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
1
3 To change the display order, select* files and then click UP or DOWN button on the
menu bar to move them onto your desired place, or select files and then drag and drop
them onto your desired place with mouse.
2
1
4 To change the display time* , select* files and
then click Display time button on the menu
bar to display the Display time setting window.
Check "Display time" check box and set display
time. To cancel the display time, un-check the
"Display time" check box.
Image frame on the index window
Image frame on the index window has 3 kinds of display modes as follows.
No frame
Blue frame
Red frame
: Shows that the image in the folder is unchanged
: Shows that image is added into the folder newly
: Shows that image is deleted from the folder
Added
Moved
*1 Enable to select multiple files at once by using "Shift" or "Control" key, or with mouse cursor.
*2 Enable to set up 3 to 240 seconds for display time.
ꢆꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a program file [Program Editor]
Example of the created program selection
Use the web browser to access to the control page of the projector. Click Viewer of the
Network menu on the web page, then connect to the FTP server and select the program
name which was made at previous section. The projector starts displaying the images
along the program. For further information, please see "Using the Network Viewer func-
tion" (+ p.98).
✐ This function is not available in the light mode.
The limitation of the Program file
There are several limitations for the program file as follows;
* Number of programs in a root folder is less than 1000.
* Number of folders in a program is less than 100.
* Total characters of folder name is less than 255.
* Total characters of program file name is less than 63.
* Do not make a program name started with ".".
* Do not make a program name contained with following characters:
\ / : , ; * ? " < > |
* The program name started with " "(space) is registered with removing the space.
PJ-NET ORGANIZER
ꢆ7
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
Using the Network Viewer function
The Network Viewer is a function to acquire the JPEG image data from the file servers
placed in the network and project them on the screen. The projected image data are
specified with the folder unit. You can set the display period and repeating times, and also
you can register those folders as the program. *The network viewer function cannot be
used when using the network capture function.
Condition to use the Network Viewer function:
* Enables to use the FTP service with Windows 2000 Professional or XP Professional.
* User must have a full-access account to the FTP server or the FTP server allows anyone to
use with "Anonymous" account which also has a full-access mode.
* The allowed number of simultaneous access from the same IP address is more than 20.
To use this function, it is necessary to disable "pop-up block" function of the web
browser.
[1] Control by the web browser
PJ2
PJ1
PC1
PC2
JPEG
PC3
PC4
PC6
PC5
Project JPEG
images stored in
PC3 with PC2
Prog.
JPEG
FTP file server
Select input mode to "Network" previously.
1 Access to the control page on the projector by using the web browser.
From the main menu, click Network - Viewer to display the setting page.
ꢆꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the network viewer function
2 Setup the setting page [1] of Image display setting.
Item
Description
Host name............Enter the host name or IP address of FTP server,
yourftp.server etc.
Folder Path ..........Use "/"(root directory) in normal, or enter the
directory name follow the "/" as shown in the
below example if you have a specified direc-
tory in the server.
/data/
1
User ID* .................Enter your login account of the FTP server
Password* ...........Enter your password of the FTP server
1
1
Option* .................Set "Display ON" when you display the
acquired preview images on the web browser.
3 Setup the setting page [2] of Selection display setting.
Click Select after selecting from the pull-down menu "Folder Selection" or "Program
Selection" for the Display object. The list window appears and select a program or folder
and then click Set on the window.
Displays the
path of the file or
folder selected
Selects the display type either the listed
with file name or listed with thumb nail.
The thumbnail can be selected "4 divi-
sion", "6 division" or "9 division".
✐ This function is not available in the light mode.
✐ See item "Creating a Program file [Program Editor]"(+ p.93) for about program.
*1 IMPORTANT NOTICE
Please note that if you use the FTP server with personal account except anonymous
account, the user ID and password may be displayed on the browser depending on
the version of the browser. We recommend that this function should be used with the
anonymous account usually.
PJ-NET ORGANIZER
ꢆꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
When clicking Set, the file list or preview list of the selected folder or program is dis-
played on the window.
Decides a image to
start auto display with
radio button
Selects a page
The original image is displayed on
another window by clicking on
the preview image or file name
Button
Operation
<<...............................Steps down the startup image in
the auto display function
>>...............................Steps up the startup image in the
auto diaplay function
List.............................Switches to the List mode
Thumbnail............Switches to the thumbnail mode
Close.........................Close the window
✐ This function is not available in the light mode.
✐ Up to 1000 images can be displayed.
✐ When selecting "folder selection", it displays images placed at the first directory in the selected folder.
✐ The display order of the images is according to the ASCII character order when selecting "folder
selection", or is specified by the Program Editor when selecting "program selection".
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the network viewer function
4 Auto display setting and control page [3]
Repeat times
(0 to 255 times)
* 0 means endless play
1
Display period* of the
image (3 to 240 sec.)
Click here to check the
further information of
the file error
Error info.
1. Click Start button to start the auto-display. The image in the selected folder or pro-
gram is displayed on the projector's screen. The web browser opens another window
and displays the preview images on the Auto Control window sequentially.
2. Click Stop button to stop the auto-display.
• Restart the auto-display, click Restart button.
* During the auto-display stops, it enables you to display the images manually by using [<<] or
[>>] button.
3. Click End button to end the auto-display.
• When pressing the Error button, the further information of the file error is displayed.
For further error information, refer to the next page.
*1 When selecting the program file for auto-display, the display time of each image gives preference
to the setting specified by the program file over the setting specified by the auto-display function
above. The images not set the display time is according to the display time specified by the auto-
display function above.
✐ The display period is greatly affected by the network environment or the operation of multi con-
trol, so it may not display the image as the specified display period.
✐ The switching is not the same timing between the images on the screen and on the web browser.
PJ-NET ORGANIZER
101
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
Error information
Description
Error type
File Error
It is displayed when the network unit cannot acquire the correct file imag-
es from the FTP server, or when the master projector is turned off during
the multi-control.
Click Error button to check the details.
Connection Error
It may be displayed when the slave projector is using the Network Viewer
or Capture function during the multi-control. Check which projector has an
error , see item "Multi Control/Conf. & Change" (+ p.64-65).
✐ When the file error is occurred during the auto-display, you may have the alert e-mail message.
For further information, please see item "3 Option selection for sending alert mail" (+ p.39).
[2] Control by the projector
Project JPEG
images with PC2.
PJ2
PJ1
PC1
PC2
JPEG
PC3
PC4
PC6
PC5
Prog.
JPEG
FTP file server
Select input mode to "Network" pre-
viously.
1 Select "Network Viewer" icon
from "Network" menu. Press
SELECT button on the projec-
tor twice to display the network
viewer setting pallet.
Display time
Repeat times
10ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the network viewer function
2 Select "Auto" or "Manual" and then press SELECT button. When selecting "Auto", Set dis-
3 Spelaleycttim"Ceoannndercetp" eaantdtitmheens press SELECT button to start displaying. The images in the
FTP server are displayed on the screen.
✐
It enables you to browse the images by using the control buttons (▲,▼) on the remote control
or on the projector.
4 To end displaying, select "Disconnect" and then press SELECT button.
Item
Description
Auto..........................Auto display mode. Specifies display periods and repeating times
Sec. .......Display period of the image (3 to 240 sec.)
Times....repeat times (255 times maximum) * ∞ means endless play
Manual....................Manual display mode. Controls image display (browsing image backward or forward)
manually.
✐ In the automatic displaying mode [Auto], when the left-click on the remote control is pressed, pro-
jector stops automatic displaying and sets into the manual displaying mode. When pressing the
right-click, it starts automatic displaying again.
✐ The image data used for this function are the program or folder that the Network Viewer function
used last time. The projector cannot specify particular images or file servers itself.
✐ The display period is greatly affected by the network environment or the operation of multi con-
trol, so it may not display the image as the specified display period.
PJ-NET ORGANIZER
10ꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6 Network Viewer
10ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Examples of connection
Peer-To-Peer connection
Connecting the projector (PJ01) to the control computer (PC05) directly.
* UTP cross cable
Computer Name: PC05
Projector Name: PJ01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
IP Address
: 192.168.0.2
: 255.255.255.0
:
:
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Connecting the projector (PJ01) to the control computer (PC05) via the hub.
Hub
To another network
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
Projector Name: PJ01
: 255.255.255.0
:
:
IP Address
: 192.168.0.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Computer Name: PC10
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.10
: 255.255.255.0
:
:
✐ When the projector is connected to the computer directly without hub, the UTP cross cable
should be used.
10ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of connection
The gateway (Router) installed in the network
Connecting the projector (PJ01) to the control computer (PC05) via the gateway.
Entrance hall
Computer Name
IP Address
Subnet Mask
: PC205
: 192.168.200.5
: 255.255.255.0
Default Gateway : 192.168.200.1
DNS : 192.168.201.1
Projector Name: PJ01
IP Address
Subnet Mask
: 192.168.200.15
: 255.255.255.0
Default Gateway : 192.168.200.1
DNS
: 192.168.201.1
Hub
Network Group: 192.168.200.x
IP Address : 192.168.200.1
Gateway (Router)
To another network
IP Address : 192.168.100.1
IP Address : 192.168.10.1
Office
Hub
Hub
Computer Name: PC05
Computer Name
IP Address
Subnet Mask
Default Gateway : 192.168.10.1
DNS : 192.168.201.1
: PC10
: 192.168.10.10
: 255.255.255.0
Computer Name
IP Address
Subnet Mask
Default Gateway : 192.168.10.1
DNS : 192.168.201.1
: PC51
: 192.168.10.51
: 255.255.255.0
Computer Name
IP Address
Subnet Mask
Default Gateway : 192.168.10.1
DNS
: PC61
: 192.168.10.61
: 255.255.255.0
IP Address
Subnet Mask
: 192.168.10.5
: 255.255.255.0
Default Gateway : 192.168.10.1
DNS : 192.168.201.1
: 192.168.201.1
Network Group: 192.168.10.x
PJ-NET ORGANIZER
107
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Web browser setting
This product is designed to enable the projector to be set up and controlled from an
Internet web browser. Depending on the preference settings of the web browser, some
control functions may not be available. Please make sure that the following functions are
set up properly in the web browser.
Active Script/JavaScript enable
There are some control items used with
the JavaScript function in the setting
pages. If the web browser is set not to use
this JavaScript function, it may not control
the projector properly. In this case, the fol-
lowing warning message will be displayed
on the top of the page. To enable the
JavaScript, please see further instructions
on the next page.
Flash Player enable
The setting page of this product contains
the Flash contents. To display the setting
page, the Adobe Flash Player version 6
or later is required to be installed on your
computer. For further product informa-
tion, see the Adobe homepage. (http://
www.adobe.com). Even if your computer
provides the Adobe Flash Player and the
setting page does not appear on the web
browser, check that Flash Player Plug-
In(Shockwave Flash) is installed and set up correctly. please see further instructions on the
next page and it is depending on the web browser.
Proxy setting
In some cases, your web browser is set up to use the proxy server for the internet or
intranet connection. In this case, when you install this product into the local network, you
should set up the proxy setting of web browser preference correctly. Especially when con-
necting the projector and computer with a UTP cross cable directly, or when the network
does not provide the proxy server, make sure that "not use proxy server" is set up in your
web browser preference. Please see item "Examples: OS/Browsers" in the next page for
further setting up procedure.
✐ There are various ways to change your browser preferences depending on the version or applica-
tions. Please see the setting instructions on next page for example and also refer to on-line help
of your web browser.
10ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Web browser setting
Examples: OS/Browsers
Windows XP Professional
Internet Explorer v.6.0
ActiveScript setting
Select Internet Options from Tools menu on the web browser and then select Security
tab and click Customize Level… button. On the security setting window, scroll down and
find the Scripting item, make sure that "Enable" is selected in item Active Scripting.
Flash Player enable
ActiveX controls and plug-ins setting
Select Internet Options from Tools menu
on the web browser and then select Security
tab and click Customize Level… button. On
the security setting window, scroll down and
find the ActiveX controls and Plug-ins item,
make sure that "Enable" is selected in item Run
ActiveX controls and plug-ins.
PJ-NET ORGANIZER
10ꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Flash Player Add-on setting
Select Manage Add-ons... from Tools
menu on the web browser. Select "Add-ons
currently located in Internet Explorer" from
Show pull-down menu. Make sure that the
"Shockwave Flash Object" is listed under the
item "Enabled".
Proxy setting
Select Internet Options from Tools
menu on the web browser and then select
Connection tab and click LAN Settings
button. Properly set up your web browser's the proxy server settings according to the
local area network environment to which the projector is connected.
- Using proxy server
To use an external internet connection from the local area network, check the item Use a
proxy server and enter the proxy server address and port correctly in the proxy settings
window. For further instruction please consult your network administrator.
- Not using proxy server
Uncheck the item Use a proxy server.
If you connect the projector to the computer directly with UTP cross cable, this must be
unchecked.
To designate proxy settings that will not use the
proxy server when accessing the projector installed
in the local area network, enter the IP address or
domain name here.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Web browser setting
Netscape Navigator v.ꢀ.0
JavaScript Setting
Select Preference from Edit
menu on the web browser
an d th en s ele c t th e item
Advanced/Scripts & Plugins
in the Category column. Make
sure that the Enable JavaScript
for Navigator is checked.
Flash Player enable
Flash Player Plug-in setting
Select About:Plug-ins from Help
menu on the web browser. The
plug-ins software provided on the
browser are listed on the page.
Check that the Flash Player Plug-
in (Shockwave Flash) is installed
and set up correctly as the below.
PJ-NET ORGANIZER
111
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Proxy setting
Select Preference from Edit menu on the web browser and then select the item Advanced/
Proxies in the Category column. Properly set up your web browser's the proxy server set-
tings according to the local area network environment to which the projector is connected.
- Using proxy server
When you use an external internet connection from the local area network, select the item
Manual proxy configuration. Enter the proxy server address and port number correctly on
HTTP Proxy item. For further instruction please consult your network administrator.
- Not using proxy server
Select the item Direct connection to the Internet in the proxy setting window.
If you connect the projector to the computer directly with UTP cross cable, this must be
selected.
To designate proxy settings that will not use
the proxy server when accessing the projec-
tor installed in the local area network, enter
the IP address or domain name here.
11ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Product specification
Product specification
Type.......................................................... PJ-Net Organizer (network unit)
LAN interface...................................... Applicant regulation IEEE802.3 (10Base-T)
IEEE802.3u (100Base-TX)
Data transfer speed
Data transfer mode
10Mbps/100Mbps
Half duplex/Full Duplex
8-pin modular (RJ-45)
TCP/IP
Terminal
Network protocol.............................TCP/IP specification
Power source...................................... Supplied from the projector
Power consumption...................... 3.0 watts
Dimensions (W x H x D)............... 5.20" x 4.13”x 1.32”(132 x 105 x 33.6 x mm)
Weight.................................................... 0.57 lbs (258 g)
Built-in battery................................... Lithium battery, Type CR2032, 3.0V
Operating temperature ............... 41˚F ~ 95 ˚F (5˚C ~ 35 ˚C)
Storage temperature..................... 14˚F ~ 140˚F (-10˚C ~ 60˚C)
* The specifications are subject to change without notice.
PJ-NET ORGANIZER
11ꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Port specification
LAN port specification
8-pin modular connector (RJ-45)
1 2 3 4 5 6 7 8
Pin No.
Signal
Function
1
2
3
4
5
6
7
8
TX+
TX-
Transfer data (+)
Transfer data (-)
Receive data (+)
RD+
(not used)
(not used)
RD-
Receive data (-)
(not used)
(not used)
11ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q&A
Installation/Access
Q
A
Why doesn’t the setting page appear in my web browser?
Following causes are possible. Please check them.
1. The projector does not connect to the network.
Check LED indicators status (+ p.17).
- Check the connection of LAN cable if the LINK indicator does not illuminate
red.
- Check the network configuration of the projector if ACT indicator does not
illuminate green.
2. Function "Network" in the projector is not set to "ON".
Set up by using the projector’s on-screen menu (+ p.20).
3. Wrong network configuration of the projector
Check the network configuration of the projector by using the projector’s
on-screen menu (+ p.20).
4. Wrong network configuration of the computer.
Check the network configuration of the computer.
5. The network unit is used with the default setting (+ p.20).
6. The proxy setting of the web browser is not set correctly (+ p.108).
7. The computer does not provide TCP/IP protocol.
Q
A
No setting page in my web browser? Is the problem in the network or in the
projector? I would like to find out the problem whether it is in the network
or in the projector
Check it by the following steps
1. Disconnect the projector from the network and connect the projector and
computer with the UTP cross cable directly.
2. Change network configuration of the computer and projector as shown in the
example below.
(Projector setting)
IP Address
Subnet Mask
Default gateway
DNS
(Computer setting)
IP Address
Subnet Mask
Default gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 192.168.0.5
: 255.255.255.0
: (blank)
: 0.0.0.0
: (blank)
PJ-NET ORGANIZER
11ꢃ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
3. Enter the projector’s IP address [192.168.0.2] at "Address" column on the Web
browser. [Note] Make sure that the proxy setting of your web browser is set
"Not use a proxy server" (+ p.108).
4. If the login page appears, this product is operating properly. The problems
may be in the network configuration of the computer or in the network. Please
try to set up the network by following item "Network configuration" (+ p.20).
If the login page does not appear, please check for proper mounting of this
product onto the projector by referring to chapter "Installation and Network
configuration" (+ p.18-19).
Q
A
How can I restrict access from the computer.
1. Please use the password authentication function on the login page (+ p.30).
2. Please use the IP filtering function provided with the gateway (router) to
restrict the accessing from the computer. For further information please con-
sult your network administrator.
Q
A
Can I access the projector installed on the company’s local area network
from a remote location?
There are some ways to access to the projector in the LAN, but you must consult your
network administrator for security reason.
☛ Use of modem
(Connect to the company’s network from your home or some other places by
using modem.)
☛ Use of private line
(Connect to the company’s network from the branch office or maintenance
office by using private line.)
☛ Use of internet
(Connect to the company’s network from your home, branch office or some
other places by using the internet.)
Q
A
We use the DHCP/BOOTP server to assign the IP address. Is it possible to use
the network unit in this network environment?
Possible. As the network unit does not support the DHCP/BOOTP server, the fixed IP
address must be configured manually. Please consult your network administrator (+
p.24).
11ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
How can I install several projectors equipped with the network unit?
Install and configure network one by one to avoid the IP address collision each other
(+ p.24).
To configure the IP address please see item "Network configuration" (+ p.20).
Q
A
How many projectors can I control with multi-control function?
It has been designed to control up to 100 sets but it depends on the network envi-
ronment.
Password/Login
Q
A
What should I do when I forget the password?
Select "Network PIN code" sub menu from "Network" menu on the projector. For fur-
ther information, please see item "Network PIN code setting" (+p. 22).
Q
A
Can I register the setting page as a web browser "Favorites" or
"Bookmarks"?
Please add "Login" page to your "Favorites" or "Bookmarks". Do not add the specified
setting page because it will not be able to perform the password authentication cor-
rectly.
PJ-NET ORGANIZER
117
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Operation
Q
A
Why can't I change the controls in the setting page with web browser?
Please make sure the projector is turned on. If it is in the standby mode, the setting
is not effective to the projector. To control the projector with a web browser, the
projector must be in the powered-on condition. Also, projectors registered for multi-
control cannot have any controls changed if they are in standby mode. But timer and
clock settings are always effective, even for projectors in standby mode.
Q
A
Why does it sometimes take a lot of time to complete the page display?
The display speed of the page depends on the network environment in which both
the projector and computer are placed. It may take much time to complete the page
display if network traffic is heavy. Please consult your network administrator. You can
select the Light mode for displaying pages quickly (+ p.30).
Q
A
I use many of the projectors in the network. How can I use names of the pro-
jectors to recognize each projector instead of IP addresses?
You can manage the projectors with nicknames instead of the IP address. Please see
item "Multi-Controls" for further information (+ p.62).
By registering the projector name and IP address with the DNS server, it can be
accessed with the nickname from the any computer referred to the DNS server.
Please consult your network administrator.
Q
A
How many numbers of the E-mail address can I register in the E-mail set-
ting page.
You can register up to 10 addresses.
11ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
Why am I not receiving E-mail alert messages?
Make sure that the registered E-mail address and SMTP server address are correct. If
the SMTP server is located in your LAN (Local Area network), the address should be
set to the SMTP server in your LAN. The SMTP server located outside of your LAN may
not be available for security reason. For further information please contact your net-
work administrator (+ p.38).
It may be required for the authentication depending on the SMTP server. This prod-
uct does not support this kind of SMTP server.
PJ-NET ORGANIZER
11ꢆ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Q
A
Can I update the firmware of the network unit.
It is possible to update the firmware through the network. It is required to have a spe-
cial tool for the updating. For further information please consult your local dealer. The
version number of the firmware is indicated on the lower part of the "Initial setting"
page.
Version of the
firmware
1ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
Q
A
What are the rules for IP address assignment?
If the network is constructed with TCP/IP protocol, a unique IP address is required for
each piece of network equipment. The following are basic rules of the assignment.
Rule1
Do not configure the same IP address to the network equipment in the same
network group. Each piece of equipment must be assigned a unique IP
address.
If the IP address is set [192.168.x.x], the Subnet Mask should be set
[255.255.255.0] for example.
Rule2
The start address [xxx.xxx.xxx.0] and the last address [xxx.xxx.xxx.255] of
the IP address must not be assigned to any other equipment. These address
numbers are reserved.
Rule3
The IP address must correlate to a network number. If network numbers are
different between the equipment, they cannot establish communications
each other. In this case, the router is placed in the networks to make the rout-
ing.
Q
A
What is the MAC address assigned to the network unit?
The MAC address is indicated on the case back as the below.
MAC Address
MAC address
PJ-NET ORGANIZER
1ꢀ1
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7 Appendix
Network capture
Q
A
Why doesn’t the computer screen appear on the projected screen?
1. Make sure that the input mode of the projector is "Network".
2. Make sure that the Network Capture icon on the task bar of the computer is active
(+ p.70).
3. Check the parameter set up (+ p.71).
Make sure that the numbers of the capture port is the same as the projector’s
port number. The default port number is 9000. If the alert message "Invalid Port
No." appears, your computer may be using this pot number already. In this case,
use another port number.
4. Check the IP address of the computer is registered to the network unit correctly
(+ p. 72).
5. Make sure that your computer is not using the firewall function. The network unit
may not be able to use the port due to this firewall function. In this case, please
turn off this function temporarily. There are also some port limitations on the net-
work equipment such as router. Please consult your network administrator.
Network Viewer
Q
A
Images from the file server don’t appear on the screen?
1. Make sure that the input mode of the projector is "Network".
2. Check the account setting of the FTP server (+ p.99).
3. The files in the FTP server must be optimized JPEG and converted by using the File
Converter 1 or 2. Please check data format. (+ p.89)
4. There are several limitations for image file name and program name. Please check
file names and program names (+ p.97).
5. Make sure that your computer is not using the firewall function. The network unit
may not be able to use the port due to this firewall function. In this case, please
turn off this function temporarily. There are also some port limitations on the net-
work equipment such as router. Please consult your network administrator.
Q
A
I cannot make a new program file.
Check your account of the FTP server. You must have a mode "Write enable" for its
account.(+ p.93)
1ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Q&A
File Converter 1
Q
A
What kind of image formats can I convert?
The File Converter 1 enables to convert to the JPEG format from the following image
format.
Bitmap format (.bmp)
JPEG format (.jpeg .jpg)
Microsoft power point format (.ppt)
File Converter 2
Q
A
Sometime I have the white frame images converted by the File Converter
2?
It may have images with white frame due to the paper margin of the print driver
depending on the image data.
PJ-NET ORGANIZER
1ꢀꢁ
OWNER'S MANUAL [XP57 Series]
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S MANUAL POA-PN03C for XP57 Series
IFEF (b)
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|