Sanyo Flat Panel Television CE32DFN2 B User Guide

INSTRUCTION MANUAL  
Colour Television  
CE28DFN2-B  
CE32DFN2-B  
Please read this Instruction book before using your television.  
We wish you many hours of pleasure from your new television.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Connecting DVD / VCR player or Satellite receiver.  
Please make sure that you have read the End-User section on page 2  
before you activate Plug and Play.  
We recommend that you connect all other equipment before Plug and  
Play. The following examples are our recommended standard  
connection. For further information please consult your local dealer.  
Step : 1 Connections ( Essential)  
Connect your aerial cable socket to the back of the TV set. Fit the aerial  
cable as shown below or as shown opposite when AV equipment is con-  
nected.  
TV rear panel  
AV1  
AV2  
ANT.75‰  
AV2  
AV1  
ANT.75  
Option if no DVD  
Connect the power cord of the TV set to a wall outlet.  
VCR  
OUT  
IN  
AC Mains Outlet  
The TV set is prepared for a mains voltage AC220~240V, 50Hz.  
OUT  
IN  
Satellite  
WARNING! High voltages are used in the operation of  
this set. Refer service to qualified service personnel.  
DISH  
IN  
TV  
VCR  
When the TV set is not to be used for an extended period of time,  
it is advisable to disconnect the power cord from the power outlet.  
For Satellite  
only  
For all aerial problems please consult your local dealer.  
DVD  
Important:  
This equipment is fitted with an approved non rewireable UK mains  
plug. To change a fuse in this type of plug proceed as follows:  
Please refer to individual Instruction Manuals for each piece of equip-  
ment for their connection suggestions.  
1. Remove the fuse cover and fuse.  
2. Fit a new fuse which should be a BS1362 5Amp A.S.T.A. or BSI  
approved type.  
Step : 2 Remote control battery installation  
3. Ensure that the fuse cover is correctly refitted.  
If the fuse cover is lost or damaged the plug must NOT be used but  
replaced with a serviceable plug.  
If the fitted plug is not suitable for your socket outlets, it should be  
cut off and an appropriate plug fitted in its place. If the mains plug  
contains a fuse, this should have a rating of 5 Amp, ensure the fuse  
cover is correctly fitted. If a plug without a fuse is used, the fuse at  
the distribution board should not be greater than 5 Amp.  
Note: The severed plug must be destroyed to avoid a possible  
shock hazard should it be inserted into a 13Amp socket elsewhere.  
The wires in this mains lead are coloured in accordance with the  
following code:  
Blue -------> Neutral  
Brown ----> Live  
Install two "AA" 1.5 volt batteries so that the "+" and "-" marks on the  
batteries match the "+" and "-" marks inside the unit into the remote  
control handset.  
1. The Blue wire must be connected to the terminal whichis marked  
with the letter “N” or coloured BLACK.  
2. The Brown wire must be connected to the terminal with the letter  
“L” or coloured RED.  
3. Do not connect either wire to the earth terminal in the symbol or  
coloured GREEN or GREEN and YELLOW.  
Before replacing the plug cover, make certain that the cord grip is  
clamped over the sheath of the lead - not simply over the wires.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
TV front controls / Terminals  
Step : 3 Switching on / Plug & Play  
Press the Mains on off switch on the front of the TV set.  
The self-automatic tuning system called  
Plug and Play will start. The TV scans  
the analogue channels first and then  
P
P
Press 5 and 6 increases or decreases the programme position.  
switches to digital channel mode and  
scans digital channels. This could take up  
to 15 minutes. During automatic tuning,  
the TV displays the tuning status of analogue and digital channel  
tuning on the screen.  
Press 1 or 2 increases or decreases the sound volume.  
Mains ON/OFF  
Power indicator.  
Thank you for purchasing your  
SANYO TV.  
Now I am searching and storing all  
programmes. Please wait.  
Analogue Set-up completed  
Next digital Set-up is starting  
Front terminals  
AV3 Video/ Audio-input Jacks  
Headphone  
Jack  
Scan for channels  
Channels found  
Scan for channels  
Channels found  
0
55  
The scan will take approximately 3 minutes  
RET  
Camcorder  
From Camcorder  
In progress  
Stop  
OK  
or video game  
Done  
Save  
Game  
equipment  
equipment  
Press OK to save.  
All channels  
1
2
3
4
5
6
7
8
9
BBC ONE  
BBC TWO  
ITV 1  
Channel 4  
five  
To select the AV3 mode press the v button repeatedly.  
When the headphones are inserted the sound from the TV  
speakers is muted.  
ITV 2  
BBC THREE  
Teletext  
BBC FOUR  
10 Sky Travel  
11 UK History  
12 Ch 14  
13 CH 15  
14 QVC  
3.5 mm Mini Headphone din  
AV3 Video in  
15 TV Travel Shop  
AV3 Left Audio in  
L/S  
R/D  
OK  
RET  
Watch TV  
Cancel  
AV3 Right Audio in  
Press OK to Watch TV.  
Now the installation is complete!  
After Plug & Play, Digital channels are stored in the programme posi-  
tions shown in the All channel table.  
Analogue channels will be automatically sorted as follows:  
Programme position 1 : BBC1  
Programme position 2 : BBC2  
Programme position 3 : ITV  
Programme position 4 : CH4 or S4C  
Programme position 5 : CH5  
Programme position 6 : ITV2  
Programme position 7 : channels in order found.  
If any other channels are available in your reception area, the  
remaining channels will be stored from programme position 7 in  
sequence as found.  
If you move to another city or cable is installed, please follow the  
description “TUNING”. (on page 13).  
This procedure only appears the first time you switch on.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOTE CONTROL - Digital Use  
Screen mode selector  
Sound mute  
To select the screen mode, AUTO, NATURAL,  
ZOOM14:9, TITLE IN 14:9, ZOOM 16:9,  
TITLE-IN 16:9, FULL or NORMAL.  
To switch the sound from the speakers.  
The sound changes as follows;  
Normal volume -> Half volume -> Mute  
Standby/Power on/off  
To switch the TV on and off.  
Also see page 14.  
TV/AV switch  
To switch from Digital TV, AV1, AV2 or  
AV3 mode press repeatedly.  
Picture mode selector  
To access a series of picture modes:  
PERSONAL, STANDARD, ECO and  
DYNAMIC.  
Direct programme selector  
For direct access to programmes  
using (0-9) numeric buttons for example  
for channel 23, press 2 and 3 numeric  
buttons.  
System selector  
To select the colour system in the AV mode,  
AUTO,PAL,NTSC 4.43 or NTSC3.58.  
Coloured buttons  
Some channels have interactive services.  
Use the red button to enter and other  
colours as directed. Also used in menu  
functions.  
Volume up/down  
To adjust the sound level.  
Programme up and down  
To select the next programme number or  
previous programme number.  
MENU  
To switch on the screen display menu on/off.  
See page 6.  
INFO  
Shows the current and next programme on  
the selected channel. (refer to page 11).  
Cursors  
To select the sub menu items in the  
menu display, Up, Down, Left, Right.  
D/A selector  
To switch between analogue and digital channels.  
Guide  
To call up the Digital TV schedule guide display on  
the screen. (refer to page 11).  
Return  
Returns back to previous screen in menu.  
Exits interactive mode.  
Surround mode selector  
To select the surround mode, ACTIVE,  
MONO or OFF.  
Subtitle  
OK  
Displays sub titles On and Off.  
You may need to switch to title in by pressing  
WIDE button. See page 17.  
To save the setting in the menu, or to call up  
the All channel table.  
Bass selection  
To get an emphasised bass sound, ON or OFF.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
User Lists  
Main menu  
You can set up different user lists to allow quick access to your  
favourite channels.  
The main menu screen takes you to  
Main Menu  
many functions in the TV. The buttons  
below are the main buttons and their  
uses.  
Picture  
Sound  
User lists  
Parental lock  
Configuration  
Channel list  
Technical information  
Timer recording  
Off Timer  
Setting User Lists  
Your TV lists  
MENU button - Enters and exits menus.  
1. Press MENU button to select  
main menu.  
List 1  
List 1  
List 1  
List 1  
List 1  
List 1  
List 1  
List 1  
Cursors e and d moves up and down  
in each selected menu.  
2. Select User Lists by pressing d  
button.  
TV settings  
Cursor 7 changes levels, moves to the  
left and returns to previous menu.  
3. Select Your TV lists menu by  
Cursor 8 changes levels, moves to the right and enters next menu.  
8
pressing  
button.  
List 1  
1
Free slot  
RETURN button - Returns to the previous screen.  
2
4. Select a List eg. List 1 by pressing  
e or d button. Enter by pressing  
8 button  
3
4
5
6
Picture menu  
7
8
9
10  
11  
12  
Refer to bar at bottom of screen for added help in which buttons to  
use.  
5. Press 8 to add channels to your  
list. Use e or d to highlight chan-  
nel selection. Press OK to add to  
your list, a X will appear next to  
the channel.  
Add channels  
Move selection  
Rename list  
R
Remove  
Swap  
G
B
Y
OK Save  
1. Press the MENU button and select Picture using e or d but-  
tons.  
List 1  
All channels  
1
2
3
4
5
6
7
8
9
BBC ONE  
BBC TWO  
ITV 1  
Channel 4  
five  
X
BBC ONE  
2. Press 8 to select.  
6. Repeat to add all the channels  
you want in your list.  
Free  
Select using e , d buttons and adjust to obtain the best picture set-  
tings for your environment using 7 , 8 buttons.  
ITV 2  
BBC THREE  
Teletext  
BBC FOUR  
7. Press Blue button to save  
selection.  
10 Sky Travel  
11 UKHistory  
12 Ch 14  
13 CH 15  
Brightness  
Contrast  
Colour  
Sharpness  
memory?  
8. Add more channels, move  
selection, rename list, remove or  
swap or press the OK button to  
finish the list or MENU to exit.  
OK  
B
Select  
Save  
List 1  
BBC ONE  
Free  
1
BBC ONE  
BBC TWO  
ITV 1  
Channel 4  
five  
2
3
4
5
6
7
8
9
Move selection.  
Tint : Colour phase if NTSC equipment is detected.  
To change the order of channels in  
your list.  
Brightness  
Contrast  
Colour  
ITV 2  
BBC THREE  
BBC FOUR  
UKHistory  
Sharpness  
1. Select the channel you wish to  
move using the e or d buttons..  
memory ?  
memory  
G
Put here  
2. Press the Green button to select  
the channel.  
Storing personal picture preferences  
3. Use  
4. Press the Green button to save the new order.  
Repeat steps 1-4 until all channels are in the order you need.  
e or d to move to a different position  
If you have altered any of the settings in the Picture menu you can  
store them. You can be recall again later.  
In the picture menu select memory by pressing the d button.  
Press the 8 button, a tick appears in the box and the settings are  
stored.  
5. Add more channels, move selection, rename list, remove or swap  
or press the OK button to finish the list or MENU to exit.  
Press the MENU button repeatedly to exit the menu.  
Rename List.  
Sound menu  
1. Press Blue button to rename your list. see picture.  
Press the MENU button and select Sound using e or d buttons,  
press the 8 button to enter.  
Rename list  
?
OK  
RET  
Cancel  
Choose letter  
Save  
Volume  
10  
Bass  
Treble  
Balance  
2. Use 7 or 8 to move left or right.  
3. Use e or d buttons to choose a letter, symbol or number. (A-Z,  
0-9, -,+ etc.)  
Select and adjust to obtain the best sound settings for your environ-  
ment using e , d and 7 , 8 buttons.  
4. Press OK to save new user list name.  
Press MENU to return to Main Menu. These settings automatically  
store when you exit the menu.  
5. Add more channels, move selection, rename list, remove or swap  
or press the OK button to finish the list or MENU to exit.  
Press MENU repeatedly to exit menu.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
Remove a channel.  
5. Select New code by pressing d button, and enter your new code  
eg. 4 3 2 1.  
1. Highlight a channel to be removed.  
6. Select Confirm new code by pressing the d button, and re-enter  
the code 4 3 2 1.  
2. Press Red button and it will be deleted, the screen shows a red  
line through it. To deselect a deleted channel press Red button  
again.  
7. If you are happy with the new code press OK to select. A prompt  
Save new code? will appear. Press the Red button to confirm.  
Red button refers to coloured buttons Red, Green, Yellow and  
Blue. Do not get confused with larger Red Standby button.  
If Invalid code! appears you have entered the incorrect old code.  
Press RETURN button and try again.  
3. Add more channels, move selection, rename list, remove or swap  
or press the OK button to finish the list or MENU to exit.  
Press MENU to return to normal picture.  
To activate parental lock.  
Swap channels.  
1. Press the MENU button to select Main menu.  
2. Using e or d buttons select Parental lock. Press 8 to enter.  
1. Choose a channel that you wish to swap with another by pressing  
the e or d buttons . Press the Yellow button to enter the Swap  
screen.  
3. Enter your code and press OK to save. If wrong code is entered  
Invalid code! will appear and you have to repeat 1-3 again.  
Swap  
?
OK  
RET  
Cancel  
Save  
Enter parental code  
?
2. Use 7 , 8 and numeric buttons to enter channel number and  
press OK to swap.( When in swap screen you can press RETURN  
repeatedly to take you back a screen).  
OK  
RET  
Cancel  
Save  
Parental lock is now activated you will now have to enter the code  
every time before you can enterMain menu unless parental lock is  
deactivated. See page 8.  
3. Add more channels, move selection, rename list, remove or swap  
or press the OK button to finish the list or MENU to exit.  
Blocking access to selected channels.  
1. Press the MENU button to select Main menu.  
2. Using e or d buttons select Channel List. Press 8 to enter.  
Channel list  
4. Press Menu to return to normal picture.  
Using User Lists  
When watching a digital channel. Press the 8 button. A title bar  
appears at the bottom of the screen with each press of the 8 but-  
ton it will select All channels and all your set user lists.  
Lock channels  
Scan for channels  
1 BBC ONE  
2 BBC TWO  
All Channels  
MY LIST 1  
3. Select Lock channels Using e or d buttons. Press 8 to enter.  
Lock channels  
BBC ONE  
All channels  
1
2
3
4
5
6
7
8
9
BBC ONE  
BBC TWO  
ITV 1  
Channel 4  
five  
Use the e or d buttons to browse through the list, the TV will  
switch to this channel. ( Only channels in the selected list will be  
browsed).  
ITV 2  
BBC THREE  
Teletext  
BBC FOUR  
10 Sky Travel  
11 UK History  
12 Ch 14  
Parental lock  
13 CH 15  
Parental lock can be used to block entry into the Menu functions and  
to allow you to block access to selected channels.  
14 QVC  
15 TV Travel Shop  
Y
OK  
Save  
Parental lock  
The first time you use this function the code numbers are 1 2 3 4.  
If you forget the code there is a default code 6 9 3 1 this will always  
give you access to Parental lock.  
4. Using e or d buttons select a Channel you wish to lock.  
5. Press Yellow button, a locked symbol will appear to show it is  
selected. To de-select press Yellow button again. Repeat until all  
channels you wish to lock are selected.  
How to change the code to your own preference.  
1. Press MENU to select Main Menu.  
Edit channel list  
BBC ONE  
All channels  
BBC ONE  
BBC TWO  
2. Using e or d buttons select Configuration and press 8 to enter.  
3. Press d to select Change parental code. Press 8 to enter.  
1
2
6. Press OK to Save.  
4. Enter Old code into yellow box which is highlighted, using the 0-9  
numeric buttons (If this is the first time you have selected this  
function it will be 1 2 3 4). Use 7 button to go back and re-enter  
an incorrect digit.  
This takes you back to Channel List Menu.  
To return to normal picture press MENU button.  
Change parental code  
Old code  
New code  
Confirm new code  
* * * *  
* * * *  
* * * *  
OK  
RET  
Cancel  
Select  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
Language choice  
Parental lock  
Audio:  
How to watch a locked channel.  
First language  
Second language  
English  
Welsh  
1. Select a locked channel, Parental lock display appears.  
Subtitling:  
First language  
Second language  
Subtitle display  
English  
Welsh  
English  
Parental lock  
!
OK  
RET  
Cancel  
Save  
Subtitling - Select your preferences as required.  
1
BBC ONE  
All Channels  
If you wish for Welsh or Gaelic Subtitles instead of English to be  
shown (when available) then select your preference for the first  
language.  
2. Press OK button, enter the Parental code and press OK again.  
Enter parental code  
Example: as shown will give you English first language, if not  
available Welsh may be shown.  
?
OK  
RET  
Cancel  
Save  
5. To change press e or d buttons to highlight the box and press 7  
or 8 to select your preferred First language and repeat for  
Second language.  
3. The channel is temporarily unlocked until the channel is changed.  
4. Press MENU button to return to normal TV picture.  
6. Press d button to select Subtitle display. This can be set ON or  
OFF by pressing 7 or 8 buttons.  
If Parental lock is activated and you wish to record this locked  
channel, deactivate first before setting timer recording.  
7. Press OK to Save.  
To deactivate parental lock.  
1. Press the MENU button to select Main menu.  
2. Enter the Parental code.  
This takes you back to Configuration menu screen.  
Change Parental Code - See page 7 under Parental lock.  
Press MENU to return to normal TV Picture.  
3. Press OK to enter menu functions.  
Common Interface  
4. Use the e or d buttons to select Parental unlock, press 8 to  
enter.  
This TV set provides a common Interface slot on the rear of the TV  
set.  
5. Press Red button to deactivate.  
Deactivate parental lock  
!
AV2  
AV1  
OK  
RET  
Cancel  
Select  
CI  
ANT.75‰  
6. Press the MENU button to exit.  
Main menu screen will show either Parental Lock or Parental  
Unlock ( if it is use).  
Card  
1. Press MENU to select Main Menu.  
Once you have activated Parental Lock each time you need to  
enter the Main Menu you will need the code.  
2. Select Configuration by using e or d buttons. Press 8 to enter.  
Configuration  
3. Press d button to highlight Common Interface and press 8 to  
enter.  
Preferred language.  
The following screen appears to show that a card is inserted.  
Common Interface  
1. Press MENU to select Main Menu.  
2. Select Configuration by using e or d buttons. Press 8 to enter.  
Reader 1: Interface card  
3. Press d button to highlight Preferred language and press 8 to  
enter.  
OK  
RET  
Cancel  
Select  
Configuration  
When you select OK, follow the on screen directions. This will vary  
depending on the type of card inserted.  
Prefered language  
Change parental code  
Common Interface  
Important!  
Audio - Select your preferences as required.  
The TV should be turned off by the Mains Power switch when insert-  
ing or removing the Common Interface Card, otherwise it may cause  
damage to the card or the TV set.  
Example. If you speak Welsh (Gaelic) and prefer to receive Welsh  
(Gaelic) audio when it is transmitted then select Welsh (Gaelic) for  
your first Language and English as your second.  
4. Press 7 or 8 to select Language, press e or d buttons select  
second language and change your preference using 7 or 8  
buttons.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
Channel List  
Technical Information  
Edit channel list  
In this section a lot of the information will only be useful to a techni-  
cian. Some parts are however useful to you. If there is an upgrade in  
software you will need this section to upgrade your TV from time to  
time.  
1. Press Menu button to select Main Menu.  
2. Select Channel List by using e or d buttons. Press 8 to  
enter.  
1. Press Menu button to select Main Menu.  
2. Select Technical Information menu by using e or d buttons.  
Press 8 to enter.  
Channel list  
Lock channels  
Scan for channels  
Technical information  
Signal information  
Software upgrade  
Product data  
Reset  
3. Select Lock channels by using e or d buttons. Press 8 to  
enter.  
Lock channels  
BBC ONE  
All channels  
1
2
3
4
5
6
7
8
9
BBC ONE  
BBC TWO  
ITV 1  
Channel 4  
five  
3. Select Signal information by using e or d buttons and press  
8 to enter.  
Signal information  
BBC THREE (BBC)  
Free  
DVB Identifiers (9018,4103,4351)  
Channel 63  
Signal strength (%) 34  
Bit error rate  
Uncorrected errors/sec  
ITV 2  
BBC THREE  
Teletext  
BBC FOUR  
10 Sky Travel  
11 UK History  
12 Ch 14  
13 CH 15  
14 QVC  
15 TV Travel Shop  
OK  
RET  
Cancel  
Select  
Y
OK  
Save  
Parental lock  
This screen cannot be altered but if you have a problem you may  
need to refer to this screen for some data.  
4. To delete channels from this list use e or d buttons to highlight  
a channel.  
4. Press Return or OK button to go back to Technical information  
screen.  
6. To lock or unlock parental locked channels, select the channel and  
press the yellow button. This will lock or unlock the channel.  
Software upgrade  
7. Press the OK button, selected channels will be locked / unlocked  
1. Press d button to select Software Upgrade screen. Press 8 to  
enter.  
and parental lock/unlock stored.  
You will go back to Channel List menu.  
Scan for channels  
Software upgrade  
Looking for new version.......  
1. Press Menu button to select Main Menu.  
RET  
Cancel  
This looks for any new software upgrades that maybe transmitted at  
any time.  
2. Select Channel List by using e or d buttons. Press 8 to  
enter.  
2. Press Return button to go back to Technical information screen.  
3. Press d to select Scan for channels. Press 8 to enter.  
Scan for channels  
Channels found  
3. Select Product Data by using e or d buttons and press 8 to  
enter.  
0
Product data  
Product LDITPGFTG_01_00  
Software 1.9.76 build jun 25 2003 16:10:15  
Resourse 1.26.3  
The scan will take approximately 3 minutes  
RET  
In progress  
Stop  
Boot  
2.4.0  
RET  
Cancel  
This will scan all available channels. This is a useful function if you  
delete channels and want to get them back later.  
This is useful to service engineers.  
4. Press OK to save (All Channels).  
4. Press Return button to go back to Technical information screen.  
5. Press d button to select Reset screen. Press 8 to enter.  
5. Press OK again to watch normal TV picture.  
Parental lock is still saved after the scan for channels has been  
initialised.  
Reset receiver configuration?  
!
RET  
R
Cancel  
Confirm  
If you press Red button to confirm it will return all settings to factory  
(default) mode for digital channels. To start a scan for all available  
channels switch the TV set Off and On again and press D/A button  
to select digital.  
When the TV set has been initialised press OK to Save and OK to  
watch TV picture.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
Once you have set the timer recording, 5 minutes before the selected  
time the following screen appears.  
Timer recording  
- This feature is used when you wish to record a digital channel on  
your VCR.  
- In order to record digital channels you cannot watch another digital  
channel when recording. Digital channels are recorded using AV2.  
- Timer recording will switch your TV set to the digital channel at the  
preset time until the finish time is reached.  
Event #1 is due to start in 4  
minutes. Press YELLOW to switch  
now. GREEN to switch on time.  
?
RED to delete the event .BLUE to cancel.  
R
G
Y
B
Delete  
Due  
Now  
Cancel  
- Whilst timer recording is running you can switch to Analogue TV.  
- You can also switch your TV into Standby mode, the timer recording  
will switch your TV on and off back into Standby when finished.  
You can either press the Red button and delete, press the Green  
button and the channel will change at the due time, press the Yellow  
button to change to the channel now or press the Blue button to  
cancel settings.  
If you want to switch to another digital channel you must first  
cancel recording by pressing the Return button.  
If you want to switch to another digital channel you must first  
If channel has been locked (Parental lock) and you have set timer  
record for locked channel it will not record. You have to deactivate  
parental lock first.  
cancel recording by pressing the Return button.  
Timer menu  
1. Press Menu button to select Main Menu.  
2. Select Timer recording menu by using e or d buttons. Press  
8 to enter.  
Off-timer setting  
The Off timer will switch the TV set into the standby mode when the  
selected time period has elapsed.  
Current events  
Channel  
Date & time End  
Press the MENU button to select main menu. Press e or d buttons  
1 (not set) --/--/-- --:-- --:-- (not set)  
2 (not set) --/--/-- --:-- --:-- (not set)  
3 (not set) --/--/-- --:-- --:-- (not set)  
4 (not set) --/--/-- --:-- --:-- (not set)  
5 (not set) --/--/-- --:-- --:-- (not set)  
6 (not set) --/--/-- --:-- --:-- (not set)  
7 (not set) --/--/-- --:-- --:-- (not set)  
8 (not set) --/--/-- --:-- --:-- (not set)  
9 (not set) --/--/-- --:-- --:-- (not set)  
10 (not set) --/--/-- --:-- --:-- (not set)  
11 (not set) --/--/-- --:-- --:-- (not set)  
12 (not set) --/--/-- --:-- --:-- (not set)  
to select OFF Timer - Press 8 to enter OFF Timer menu.  
00 30  
00 30  
OFF-Timer  
OFF-Timer  
Set  
Not set  
Press 8 to highlight time period yellow. Press e or d buttons the  
time changes in 30 minute steps.The maximum time is 2:00hrs.  
When you are ready to store your settings press the 8 button and  
the time colour changes to green. The tick appears as shown above  
and its colour changes to yellow.  
OK  
R
RET  
Cancel  
Edit/Add event  
Delete  
If you have set the off timer, then one minute before the TV switches,  
a display appears on the screen.  
3. Highlight a row and press OK button. Set events screen appears.  
Set event  
Press MENU button or RETURN button twice to return to normal TV  
picture.  
BBC ONE  
17/07/03  
10:52  
Channel  
Wake-up day  
wake-up time  
Finish time  
Repeat  
If the TV set is switched off by the Mains Switch 4 or you enter  
,
the preset mode, the timer settings will be cancelled.  
11:28  
No repeat  
OK  
RET  
Cancel  
Save  
4. Select channel by pressing 7 or 8 buttons and rotate through all  
available channels.  
5. Press d button to select and highlight yellow Wake-up day box.  
Enter your day, month and year by using numeric buttons (0-9).  
and using 7 or 8 buttons to move left and right.  
6. Press d button to select and highlight yellow Wake-up time box.  
Enter your time by using numeric buttons (0-9). and using 7 or 8  
buttons to move left and right.  
7. Press d button to select and highlight yellow Finish time box.  
Enter your time by using numeric buttons (0-9). and using 7 or 8  
buttons to move left and right the time you wish to finish.  
8. Press d button to select and highlight yellow Repeat box. Press  
7 or 8 buttons to enter No repeat, daily, or weekly. This would  
be a useful feature if you have a favourite programme that you  
dont want to miss and it is shown on a daily or weekly schedule.  
9. Press OK to save settings, you can repeat again or press  
RETURN button to go back to Main menu. Press MENU to exit.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIGITAL OPERATION  
TV Setting menu  
Info button  
When you press the info button in digital mode you will be displayed  
a cut down guide showing only the channel you are currently on.  
Child lock  
You can prevent small children from operating the TV with the front  
buttons of the TV set.  
Wed 11:44  
20/0802003  
ITV 1  
Press the MENU button to select main menu.  
11:30-12:30  
l..........  
12:30-12:50  
ITV Lunchtime News  
Press e or d buttons to select TV settings. Press 8 to enter  
menu.  
OFF  
Main national & International news  
Child lock  
AV2  
ON  
Guide  
Prog+  
Now  
TV Schedule  
Change channel  
Press the 7 or 8 buttons to select current programme or next.  
Press the GUIDE button to go to the full guide. Press the 5 or  
6buttons to change to the channel.  
Press e or d buttons to select. Child lock can be set to ON or  
OFF. Press 7 or 8 buttons to select.  
Programme Download  
The child lock mode will be reset to “OFF” when the TV set is  
switched off with the Mains ON/OFF 3 switch.  
Once you have started the upgrade process you must not interrupt  
it (disconnect or seperate it from the mains supply) under any  
circumstances. Do not press any key on the remote control or the  
front of the cabinet. If you interrupt the upgrade process the IDTV  
may be defective afterwards.  
Setting of AV2 input mode  
If you use a VCR which has S-VHS, you should connect it to AV2  
and change the AV2 menu to S-VIDEO.  
From time to time upgrades will become available. When this hap-  
pens the following screen appears.  
S-VIDEO  
Child lock  
Software upgrade  
Download  
AV2  
VIDEO  
X
Version  
Date  
Press d to select AV2 and select VIDEO or S-VIDEO by pressing 7  
or 8 buttons.  
OK  
RET  
Cancel  
Start  
Press MENU button or RETURN button twice to return to normal  
TV picture.  
To upgrade press the OK button and the following screen will  
appear.  
Guide  
Software upgrade  
The guide shows the digital TV schedule for the next 2 hours.  
The guide can show all channels or any set user lists ( see page 6).  
This will improve your TV’s features  
Press the 8 button to select all channels or a user list then press  
GUIDE button.  
Upgrade later  
Blue  
Upgrade now  
OK  
RET  
Do not upgrade  
A schedule will appear on the screen.  
Press OK to start, this automatically downloads for you. The follow-  
ing screen appears.  
TV Schedule  
User list 1  
Wed 12:44  
20/0802003  
12:00  
XXXX  
XXXX  
Today  
14:00  
Software upgrade  
Downloading  
BBC 1  
XXXX XXXX XX  
XXXX  
XXXX  
XXXX  
ITV  
XXXX  
ITV  
Lunchtime News  
Channel 4  
five  
XXXX  
Software details  
XXXX  
XXXX  
XXXX  
XXXX  
XXXX  
UKHistory  
RET  
Cancel  
In Progress......  
12:30-12:50  
ITV Lunchtime News  
The following screen appears to show that the upgrade it nearly  
finished. Once this screen disappears the upgrade is complete.  
Main national & International news  
Info  
Software upgrade  
Use the e or d buttons to move up and down the channel list. Use  
7 or 8 buttons to highlight the programmes below the transmission  
time, progress and a brief programme explanation will be displayed.  
If this takes longer than 20 minutes  
contact your television supplier.  
In Progress......  
Press the  
button to get more information on that programme.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOTE CONTROL - Analogue  
Screen mode selector  
Sound mute  
To select the screen mode, AUTO, NATURAL,  
ZOOM14:9, TITLE IN 14:9, ZOOM 16:9,  
TITLE-IN 16:9, FULL or NORMAL.  
To switch the sound from the speakers.  
The sound changes as follows;  
Normal volume -> Half volume -> Mute  
Standby/Power on/off  
To switch the TV on and off.  
Also see page 16.  
TV/AV switch  
To switch from TV, AV1, AV2 or  
AV3 mode press repeatedly.  
Picture mode selector  
To access a series of picture modes:  
PERSONAL, STANDARD, ECO and  
DYNAMIC.  
Nicam/Bilingual selector  
To switch the sound mode as follows;  
NICAM or MONO in the stereo programmes.  
A or B in the bilingual programmes. If the  
nicam or stereo sound reception is poor in  
quality, you can switch to MONO sound  
reception by pressing A•B button. This  
operates only analogue channel mode.  
System selector  
To select the colour system in the AV mode,  
AUTO,PAL,NTSC 4.43 or NTSC3.58.  
Channel mode selection  
To enter channel number of the station  
directly. This operates in the analogue  
channel mode only. Press once to show  
current channel number. Press a second  
time to show C--, enter the channel you  
require using the 0-9 buttons. Press the OK  
button to memorise  
Direct programme selector  
For direct access to programmes  
using (0-9) numeric buttons in analogue  
and digital. For selection of analogue  
programme position 10 - 99, for example 23,  
first press -/-- button and press  
2 and 3 numeric buttons.  
Programme up and down  
To select the next programme number or  
previous programme number.  
Volume up/down  
To adjust the sound level.  
INFO  
MENU  
In the analogue mode, it displays the programme  
information such as current programme number,  
stereo status and remaining time if set, for about  
5 seconds.  
To switch on the screen display menu on/off.  
Also see page 12.  
Cursors  
To select the sub menu items in the  
menu display.  
D/A selector  
To switch between analogue and digital channels.  
Teletext/TV selector  
To switch TV, MIX and Teletext mode.  
Surround mode selector  
To select the surround mode, ACTIVE,  
MONO or OFF.  
OK  
To save the setting in the menu.  
(also refer to CS button).  
Bass selection  
To get an emphasised bass sound ON or OFF.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION - Anologue channels  
Many of your TV’s functions are controlled through the menu function.  
MENU  
Timer menu  
Off-timer setting  
Picture  
Brightness  
Contrast  
Colour  
Sharpness  
The Off timer will switch the TV set into the standby mode when the  
selected time has elapsed.  
Text bright  
memory?  
1. Press the MENU button to select main menu. Press 5 or 6 to  
Tint (only when NTSC is detected)  
select Timer.  
Sound  
Timer  
Volume  
Bass  
Treble  
Balance  
2. Press 1 to enter OFF Timer.  
3. Press 1 button, and highlight time setting column by pressing  
the  
5
or  
6
buttons.  
OFF Timer  
time setting column  
Setting Child lock  
AV2  
ON/OFF  
VIDEO/S-VIDEO  
00 30  
00 30  
OFF-Timer  
OFF-Timer  
Tuning  
Swap  
Fine Tuning  
Preset  
Not set  
Set  
AUTO  
CH:34  
P:04  
Skip OFF  
Memory?  
SEMI  
CH:34  
P:04  
Skip: OFF  
Memory?  
When the time setting column is selected its colour changes to yellow.  
The time changes in 30 minute steps.The maximum time is 2:00hrs.  
When you are ready to store your settings press the 1 button and  
the setting column numbers colour changes to green. The tick  
appears as shown above and its colour changes to yellow.  
During the menu operation the following buttons are used.  
u
: To enter the menu function.  
: To go back and to exit the menu function.  
If you have set the off timer, then one minute before the TV switches,  
a display appears on the screen.  
: To navigate up and down in the menus.  
4. Press the MENU button repeatedly to exit the menu.  
: To navigate forwards to the next screen or to  
activate settings.  
+
If the TV set is switched off by the Mains Switch 4 or you enter  
,
the preset mode, the timer settings will be cancelled.  
Picture menu  
1. Press the MENU button to select main menu, select Picture using  
e or d buttons.  
Setting menu  
Child lock  
Brightness  
Contrast  
Colour  
Sharpness  
Text bright  
memory?  
Picture  
You can prevent small children from operating the TV with the front  
buttons of the TV set.  
Sound  
Timer  
Setting  
Preset  
1. Press the MENU button and select main menu.  
2. Press 5 or 6 to select Setting, press 1 to enter Child lock  
/ AV2 menu.  
2. Press 1 to enter. Select and adjust to obtain the best picture  
settings for your environment.  
OFF  
Text bright : Brightness of Teletext screen  
Picture  
Sound  
Timer  
MINIMUM / CENTRE / MAXIMUM.  
Child lock  
AV2  
ON  
Tint :  
Colour phase if NTSC equipment is detected.  
Setting  
Preset  
Storing picture preferences  
If you have altered any of the settings in the Picture menu you can  
store them. You can be recall again later.  
3. Press  
5
or 6 to select Child lock, press 1 to select ON or  
OFF.  
In the picture menu press 6 to select memory.  
Brightness  
Contrast  
Colour  
The child lock mode will be reset to “OFF” when the TV set is  
switched off with the Mains ON/OFF 3 switch.  
Sharpness  
memory ?  
memory  
Setting menu  
Setting of AV2 input mode  
If you use a VCR which has S-VHS, you should connect it to AV2 and  
change the AV2 menu to S-VIDEO.  
Press the 1 button, a tick appears in the box and the settings are  
stored.  
Sound menu  
1. Press  
6
VIDEO.  
to select AV2, press 1 or 2 to select S-VIDEO /  
1. Press the MENU button to select main menu and using 5 or  
6 select Sound.  
Picture  
Sound  
Timer  
S-VIDEO  
Child lock  
2. Select and adjust to obtain the best sound settings for your  
environment using 5, 6, 1 or 2.  
Setting  
Preset  
AV2  
VIDEO  
Picture  
Sound  
Volume  
10  
Bass  
Treble  
Balance  
Timer  
Setting  
Preset  
2. Press MENU button repeatedly to exit.  
3. Press MENU button repeatedly to exit.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MENU OPERATION - Anologue channels  
Skip  
Preset menu  
Skip ON : in normal operation when the e or d button is pressed  
The preset menu can be used to tune new channels, to reorder  
channels and their programme positions, and to make fine adjust-  
ments to the tuning.  
this position will be skipped.  
SEMI  
ON  
CH: 34  
P: 04  
There are two ways to tune in new channels.  
OFF  
Skip:OFF  
memory?  
Auto : Searches for all channels and stores them automatically.  
Semi : Manual search to add channels.  
Tuning - Auto  
Skip OFF : Position is not skipped when e or d button is pressed.  
To select Skip Press d and press or 8 to set to ON or OFF.  
1. Press the MENU button to select main menu.  
7
2. Using e or d, select Preset, press  
d buttons.  
8
and select Tuning using e or  
You can still view a programme position that has been skipped by  
using the numeric buttons to select the programme position directly.  
Picture  
Sound  
6. Select memory by pressing the d. Press  
nel is now stored.  
8
a tick indicates the chan-  
Auto  
or  
Timer  
Tuning  
Swap  
Setting  
Preset  
Fine Tuning  
Semi  
SEMI  
CH: 34  
P: 04  
Skip:OFF  
memory  
3. Press 8 to select Auto and d to select Channel (CH:34) as  
shown.  
memory?  
CH:22  
CH:21  
AUTO  
Press MENU button repeatedly to exit and return to normal TV  
picture.  
AUTO  
CH: 34  
CH: 34  
P: 02  
Skip:OFF  
memory?  
P: 02  
Skip:OFF  
memory?  
Swap  
CH:21  
CH:22  
Use this channel swapping feature to swap the channels between  
two stored programme positions. This feature is particularly useful  
after automatic tuning.  
Press the  
7
or  
8
all available channels are stored.  
To cancel this tuning operation, press the MENU button repeatedly.  
You have to choose a programme that you wish to swap on the TV  
set. eg. Swap programme position 4 and 12.  
After completing this procedure, the TV set returns to normal TV  
mode and selects programme position “01”.  
1. Select programme position 4.  
2. Press the MENU button.  
You can change the order of the station selection, by using the  
channel swapping function detailed later.  
3. Select Preset by pressing e or d buttons. Follow the diagram  
below.  
You do not need to use Memory function at this stage as all channels  
are automatically saved.  
Picture  
Tuning  
Tuning  
Sound  
Timer  
Tuning - Semi  
Setting  
12  
Swap  
Swap  
Preset  
1. Press the MENU button to select main menu.  
Swap  
Fine Tuning  
Fine Tuning  
2. Using e or d, select Preset, press  
d buttons.  
8
and select Tuning using e or  
4. Enter the programme number (12), press 8 and the channels are  
swapped.  
Picture  
Sound  
Tuning  
Timer  
SEMI  
Auto  
CH: 34  
Fine tuning  
Setting  
Swap  
or  
P: 02  
Skip:OFF  
memory?  
Fine Tuning  
Preset  
1. Press the MENU button.  
Semi  
2. Select Preset by pressing  
e
or d buttons. Follow the diagram  
below. Press 8 to enter.  
3. Press 8 to select Semi and d to select Programme position  
(P:04) as shown where you want to store a channel.(eg. CH4)  
Picture  
Sound  
Timer  
Tuning  
Swap  
SEMI  
CH: 34  
P:06  
P:05  
Setting  
Preset  
Fine Tuning  
P: 04  
P:03  
P:02  
Skip:OFF  
memory?  
3. Press e or d to select Fine Tuning, press 8 to fine tune  
channels.  
4. Select the channel search ( CH:34) and start searching by pressing  
the  
7
or  
8
buttons.  
The tuning will be stored when you exit the menu.  
CH:36  
CH:35  
SEMI  
CH: 34  
P: 02  
Skip:OFF  
memory?  
CH:34  
CH:33  
5. When a channel is located searching stops, If you do not want this  
channel press or to search again.  
7
8
You can enter a channel number directly with the 0-9 numeric  
buttons if you know the number.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TELETEXT OPERATION - Anologue channels  
Standby/Power on/off  
To switch the TV on and off.  
Reveal switch  
This reveals hidden items on the teletext  
page eg: a hidden answer to a quiz question.  
Direct access to a page  
All the numeric buttons can be used  
to select a page number directly.  
If you need page 301, press 3 then  
0 then 1.  
Sub page access  
Some text pages are made up of several  
sub pages which rotate automatically if  
you wish to view P4 of 8 press the sub page  
button. “----” will appear. Enter 0004.  
Direct access to subject headings  
Coloured boxes are displayed at the bottom  
of the screen. The 4 coloured buttons give  
access to the corresponding subjects or pages.  
Page up and down  
To select the next page number or  
previous programme number.  
Index page selector  
To call up the Index pages.  
eg. P100.  
Teletext/TV selector  
To switch TV, MIX and Teletext mode.  
Stop  
Up / down page access  
Press the button to select the next page  
or previous page number.  
This stops the sub pages from changing.  
The word “STOP” will appear instead of  
the page number.  
Cancel  
Size switch  
To view the TV picture in the teletext mode  
while waiting for sub page to change or  
page to update.  
This will make either the top half or  
the bottom half of the page expand  
to fill the whole screen.  
Note. the page number will appear if the  
page is updated.  
Teletext  
Teletext - This is a free service to give you lots of varied informa-  
tion such as news, sports results, weather and travel features.  
Teletext reception  
If your aerial signal is poor, the teletext reception operation may be  
erratic.  
Teletext brightness level  
You can change the teletext brightness level. Please return to TV  
mode.(See Picture menu -Text Bright on page 12).  
Sound volume control  
In teletext mode sound volume and muting can be controlled.  
However they are not displayed on the screen.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ANALOGUE AND DIGITAL OPERATION  
Switching into /from standby mode  
The Standby mode is used for switching the TV set off for short  
periods of time. In standby mode the TV is switched off but is  
still receiving mains power.  
To turn the TV set into standby mode, press the 4 button.  
The red power indicator illuminates more brightly.  
To turn the TV set ON from standby mode, press any of the  
following buttons: 4  
5, 6 or 0-9 buttons.  
,
If you find the power indicator flashing, please turn the TV  
set off completely with the Mains ON/OFF switch and  
contact our Service desk.  
!
This warning is a sign to let you know that the power  
protection function of this TV set is now operating.  
Auto shut off  
This TV set will automatically switch into the standby mode, 10  
minutes after a signal is no longer received. The time until the  
set will switch off is displayed on the screen.  
also appear in digital mode.  
No signal. will  
!
When the TV set is switched on by using the ON-Timer function  
with no signal being received, this function will be ignored.  
Use of Audio Output Jacks  
This TV provides the audio monitor output jacks on the rear of the  
cabinet back. You can connect your audio equipment to these jacks  
to give you sound through your audio equipment.  
AV2  
AV1  
ANT.75  
To audio equipment  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TITLE IN (16:9)  
Selecting of picture size  
4:3  
14:9  
16:9  
Letterbox Video  
Screen options  
Today there are various transmission formats with different size  
ratios, eg. 4:3 , 14:9, 16:9 and video formats such as letterbox.  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
AUTO  
As Zoom (16:9),  
but bottom is  
compressed even  
more to allow  
subtitles to be  
seen.  
As Zoom (16:9),  
but bottom is  
compressed even  
more to allow  
subtitles to be  
seen.  
As Zoom (16:9),  
but bottom is  
compressed even  
more to allow  
subtitles to be  
seen.  
As Zoom (16:9),  
but bottom is  
compressed even  
more to allow  
subtitles to be  
seen.  
It automatically switches to the optimum screen mode according to  
the WSS signal provided in the receiving signal source. If the signal  
does not have it, the TV keeps current screen mode.  
This setting may cause the picture to change when a different for-  
mat is received eg. when an advert is received.  
WSS (Wide screen signalling)  
FULL  
Some broadcasters transmit this signal and some VCR tapes have it  
included . The signal identifies the picture format ratio (16:9, 14:9, 4:3  
etc.).  
4:3  
14:9  
16:9  
Letterbox Video  
If WSS is not being received and you are not happy with your picture  
this TV provides you the option to change it with the following options.  
The whole screen  
is filled stetching  
the width.  
The whole screen  
is filled with the  
corrrect picture  
ratio.  
The black bars top  
and bottom are  
present and the  
height is  
The whole screen  
is filled stetching  
the height slightly  
at the edges.  
Press the WIDE button repeatedly to select your desired setting.  
compressed.  
4:3  
14:9  
16:9  
Letterbox Video  
NORMAL  
4:3  
14:9  
16:9  
Letterbox Video  
Stretches the  
The height is  
The picture fills the The black bars top  
picture horizontally  
to fill the screen.  
The picture is more  
stretched at the  
edges.  
expanded to fill the  
whole screen.  
screen and is  
proportionally  
correct.  
and bottom remain  
and the height is  
compressed to fit  
the picture area.  
The correct ratio is  
maintained with  
black bars on the  
left and right.  
Black bars left and Black bars left,  
right, picture height right, top and  
Black bars left and  
right, picture height  
is stretched.  
is stretched.  
bottom.  
ZOOM (14:9)  
4:3  
14:9  
16:9  
Letterbox Video  
VCR / DVD controls  
This remote control transmitter has been designed to be used in  
conjunction with selected SANYO VCR’s and DVD players. Some  
SANYO VCR’s and DVD players may have their own functions,  
so please refer to the individual instruction booklet when using  
this remote control to ensure compatibility.  
The correct picture  
width is maintained  
but the top and  
bottom are  
Zooms in slightly  
cropping the top  
and bottom.  
The black bars top  
and bottom are  
smaller and the  
picture height is  
compressed slightly.  
Zooms in slightly  
cropping the top  
and bottom.  
cropped.  
Some of the keys are used for both the VCR and DVD player.  
The symbols indicated with blue are for the keys to control the  
DVD player. When you use the DVD player with this remote  
control, first press and hold the DVD button and then press your  
TITLE IN (14:9)  
4:3  
14:9  
16:9  
Letterbox Video  
VCR  
DVD  
Power  
Play  
Power  
Play  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
TITLES ON SCREEN  
Pause  
Stop  
Pause  
Stop  
As zoom (14:9), but As zoom (14:9), but As zoom (14:9), but As zoom (14:9), but  
bottom is  
bottom is  
bottom is  
bottom is  
Fast/Cue  
Next chapter selection  
compressed even  
more to allow  
subtitles to be  
seen.  
compressed even  
more to allow  
subtitles to be  
seen.  
compressed even  
more to allow  
subtitles to be  
seen.  
compressed even  
more to allow  
subtitles to be  
seen.  
Previous chapter selection  
Rewind/Review  
Record, press both button at same time.  
n/a  
n/a  
n/a  
DVD  
OK  
DVD command mode selection  
Enter  
Cursor selection  
ZOOM (16:9)  
desired control button each time.  
4:3  
14:9  
16:9  
Letterbox Video  
The correct picture  
width is maintained  
but the top and  
bottom are  
Zooms in slightly  
cropping the top  
and bottom.  
The black bars top  
and bottom are  
smaller and the  
picture height is  
compressed slightly.  
Zooms in slightly  
cropping the top  
and bottom.  
cropped.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV SPECIFICATIONS  
TV specifications  
Servicing  
Common specification  
Power source  
Television system  
Colour system  
Your television is fully transistorised and does not contain any  
user serviceable components.  
AC 220~240V 50Hz  
System I  
PAL/NTSC4.43  
You must not remove the rear cover of the TV by yourself. The  
apparatus is working with high voltages and could damage  
objects or even endanger people. Leave all required repair and  
service jobs to an authorised service technician. He will exclu-  
sively use such spare parts that are complying with the same  
safety standards as appliciable to the original parts. The use of  
original spare parts can prevent fire, shock and other hazards.  
(PAL/NTSC4.43/NTSC3.58 in AV mode)  
Channel coverage  
UHF: 21-69.  
75 ohm  
Aerial input impedance  
AV terminal  
AV1: CENELEC Standard  
Input: Composite video, RGB and audio-L/R  
Unplug the television receiver from the wall outlet and refer  
servicing to qualified service personnel under the following  
conditions:  
Output: TV-output with composite video and  
audio-L/R  
If the power cord or plug is damaged.  
AV2: CENELEC Standard  
Input: Composite video, RGB, S-VHS and  
audio-L/R  
If liquid has been spilt into the television  
receiver.  
!
If television receiver has been exposed to rain or water.  
Output: Monitor-output with composite video and  
audio-L/R  
If the television receiver has been dropped or the cabinet has  
been damaged.  
Front AV terminal  
Heaphone socket  
If the television receiver exhibits a distinct change in performance.  
AV3:  
Input:  
RCA jacks  
Composite video and audio-L/R  
If the television receiver does not operate normally by following  
the operating instructions.  
Mini Jack  
Adjust only those controls that are covered in the operating instruc-  
tions as improper adjustment of other controls may result in damage.  
This will often require extensive work by a qualified technician to  
restore the television receiver to normal operation.  
CE28DFN2-B  
CE32DFN2-B  
Sound output  
(Continuous)  
2 x 10W  
2 x 10W  
Picture tubes  
(inches)  
28  
32  
Dimensions  
(WxHxD mm)  
786 x 519 x 504  
34.5  
880 x 575 x 549  
46.3  
Weight (kg)  
Helpful hints  
NO PICTURE, NO SOUND  
Check if TV is plugged in.  
Try a different channel, if OK, probably station trouble.  
POOR PICTURE, SOUND OK  
Adjust BRIGHTNESS control.  
Adjust FINE TUNING control.  
Check aerial connections.  
NO COLOUR, PICTURE OK  
Adjust COLOUR control.  
Adjust FINE TUNING control.  
Is the programme in colour ?  
WEAK PICTURE  
Check aerial connections on back of set.  
Check aerial for broken wires.  
Re-orient aerial.  
The following faults are not caused by the receiver:  
"GHOSTS"  
Reflections of signals from mountains or high buildings will cause  
multiple images, called "Ghosts". These abnormal conditions can be  
reduced to minimum by repositioning aerial or by installing new one  
suited for your area.  
"INTERFERENCE"  
Interference may be caused by electrical appliances, car ignition  
systems, etc. This should normally be a temporary condition, but  
should this interference persist, contact your dealer.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY TO CUSTOMER  
Sanyo U.K. Sales Ltd. (the company) warrants to the initial retail  
Dear Customer.  
purchaser that if this equipment is or becomes defective and that,  
in the opinion of the Company, the defect is due to faulty material  
or workmanship the Company will, for a period of 12 calendar  
months from the date of sale to the original purchaser repair or  
replace, at its sole option, free of charge, any such defective  
component part of the equipment, always provided that:-  
Thank you for buying SANYO. This equipment should give you  
many years of pleasure and faithful service but in the event that a  
fault occurs, the following notes for you guidance may be helpful:-  
1: PLEASE RETAIN YOUR PURCHASE RECEIPT WHICH WILL  
BE REQUIRED FOR SERVICE DURING WARRANTY.  
2: If your Sanyo equipment proves faulty during the period of  
guarantee, take it or send it back to the dealer who originally  
supplied it together with this guarantee and the proof of  
purchase. We have made arrangements with our approved  
dealers under which they will carry out inguarantee service  
repairs on our behalf. In this way, we hope to reduce to a  
minimum the amount of time you will be without your equipment.  
1: The equipment has at all times been used in accordance with  
the operating instructions issued by the Company, and has not  
been connected to an electrical mains supply for which it has not  
been adjusted.  
2: Accidental damage or damage caused by negligence of misuse  
by the user, is specifically excluded.  
3: Unauthorised repairs, or any modification to the equipment  
which has not been expressly approved by the Company, shall  
render this warranty null and void.  
3: If for some reason it is impossible to return the equipment to the  
original supplier, please contact our Service Department at the  
address below for further advice.  
4: Failure due to fair wear and tear of any item is specifically  
excluded.  
4: Should the equipment require servicing after the expiry of the  
guarantee period, take or send it to the original supplier or any  
other Sanyo dealer. He will be pleased to give you a quotation  
for the repair.  
This warranty is not transferable and is only applicable within the  
United Kingdom (and the Republic of Ireland).  
Service Department,  
Sanyo UK Sales,  
Nothing in this express warranty affects the statutory rights  
available to the purchaser of this equipment.  
(A Division of SANYO Europe Ltd.),Sanyo House,  
Otterspool Way,  
Watford, Hertfordshire, WD2 8JX.  
Tel: 01923 246363  
Note: This warranty supersedes any other form of guarantee that  
may inadvertently have been enclosed with or attached to the  
product.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part No. 1KA6P1P0046-C  
C6AD/BD  
Printed in U.K.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Cable Box QT518 814 User Guide
Regal Ware Microwave Oven K6725 User Guide
Roland Marine Lighting cr 80 User Guide
Samsung Home Security System SSA P102 User Guide
Samsung Vacuum Cleaner SU 2930 Series User Guide
Sanyo CRT Television PLC XP55L User Guide
Sanyo DVD Player DVD SL25 User Guide
SATO Label Maker M 10e User Guide
Senco Nail Gun SCN40DW User Guide
Sennheiser Computer Hardware MD 42 User Guide