GUIDE FOR
BASIC OPERATION
VPC-CS1EX
VPC-CS1
Dual Camera
VPC-CS1GX
VPC-CS1PX
VPC-CS1TA
Important note
This manual explains how to safely operate the VPC-CS1EX, VPC-CS1,
VPC-CS1GX, VPC-CS1PX and VPC-CS1TA.
Any information regarding only one of these products will be labeled as such.
Please read these instructions carefully before using the camera.
Make sure to read and understand the separate booklet “SAFETY MANUAL”.
Keep this manual in a safe place for later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR USERS IN THE USA
About the battery charger
IMPORTANT SAFETY
INSTRUCTIONS – SAVE THESE
INSTRUCTIONS
DANGER – TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE
INSTRUCTIONS
h For connection to a supply not in the U.S.A., use an attachment plug
adapter of the proper configuration for the power outlet.
h Power Supply Cord:
Use UL Listed detachable power supply cord - No. 18 AWG, two
conductors, rated 10 A, VW-1, 105 ºC, 125/250 V, minimum 1.8 m,
maximum 3 m long. Provided with a molded-on, non-polarized attachment
plug with a 15 A, 250 V (NEMA 2-15P) configuration or a 15 A, 125 V
(NEMA 1-15P) configuration and a molded-on connector which mates with
the Power Inlet.
Cord Type
Basic Cord Type
Other Suitable Types
TST
TS
SP-2
SP-3
SV
SPE-2, SPT-2
SPE-3, SPT-3
SVE, SVO, SVOO, SVT, SVTO, SVTOO
SJE, SJO, SJOO, SJT, SJTO, SJTOO
SE, SO, SOO, ST, STO, STOO
SJ
S
h This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
English
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
PARA LOS USUARIOS DE EE.UU.
Acerca del cargador de baterías
INSTRUCCIONES IMPORTANTE
SOBRE DE SEGURIDAD - GUARDE
ESTAS INSTRUCCIONES
PELIGRO - PARA REDUCIR EL
RIESGO DE INCENDIO O
DESCARGAS ELÉCTRICAS, SIGA
CUIDADOSAMENTE ESTAS
INSTRUCCIONES
h Para la conexión a una red de alimentación que no sea de EE.UU., utilice
el adaptador de enchufe apropiado para la toma de la red.
h Cable de alimentación:
Utilice el cable de alimentación UL desenchufable indicado en la lista - N.°
18 AWG, dos conductores, amperaje nominal de 10 A, VW-1, 105 ºC, 125/
250 V, mínimo 1,8 m, máximo 3 m de longitud. Provisto de enchufe
moldeado, adaptador de enchufe no polarizado con configuración de 15 A,
250 V (NEMA 2-15P), o configuración de 15 A, 125 V (NEMA 1-15P) y
conector moldeado que se adapta a la toma de corriente de la red.
Tipo de cable
Tipo de cable básico
Otros tipos adecuados
TST
TS
SP-2
SP-3
SV
SPE-2, SPT-2
SPE-3, SPT-3
SVE, SVO, SVOO, SVT, SVTO, SVTOO
SJE, SJO, SJOO, SJT, SJTO, SJTOO
SE, SO, SOO, ST, STO, STOO
SJ
S
h Este dispositivo cumple con lo estipulado en la Parte 15 de las Normativas
de la FCC. La operación está sujeta a las dos condiciones siguientes: (1)
este dispositivo no puede provocar interferencias nocivas, y (2) este
dispositivo debe aceptar las interferencias recibidas, incluidas las
interferencias que puedan provocar un funcionamiento no deseado.
iii English
Download from Www.Somanuals.com. All Manuals Search And Download.
kFOR CANADIAN USERS
i This Class B digital apparatus complies with Canadian ICES-003.
kFOR EU USERS
The symbol mark and recycling systems described below apply to EU
countries and do not apply to countries in other areas of the world.
Your SANYO product is designed and manufactured with high quality
materials and components which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment, batteries
and accumulators, at their end-of-life, should be disposed of separately from
your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this chemical
symbol means that the battery or accumulator contains a heavy metal at a
certain concentration. This will be indicated as follows: Hg: mercury, Cd:
cadmium, Pb: lead
In the European Union there are separate collection systems for used
electrical and electronic equipment, batteries and accumulators.
Please, dispose of them correctly at your local community waste collection/
recycling centre.
Please, help us to conserve the environment we live in!
SANYO Sales & Marketing Europe GmbH
Stahlgruberring 4, D-81829 München, Germany
SANYO Electric Co., Ltd.
1-1, Sanyo-cho, Daito City, Osaka 574-8534, Japan
kFOR RUSSIAN USERS
This product is certified by an official certification company
which is authorized by the Russian Federation.
English
Download from Www.Somanuals.com. All Manuals Search And Downloiavd.
HOW TO READ THIS MANUAL
For first-time users
Please read this manual to familiarize yourself with your camera’s
operation.
↓
To use the various camera features
The Instruction Manual that explains the features in detail can be
↓
To use additional features
Visit the Sanyo website to learn how to adjust the camera settings for
various shooting scenes. There you’ll also find information about the
software for playing back data recorded with your camera and for
burning (recording) DVDs.
You may find the answers to questions or problems concerning camera
Symbols used in this manual
HINT
Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.
(page xx) Refer to the page indicated for detailed information.
v
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT, PLAY BACK AND SAVE
Preparing the camera
1
Insert the battery pack.
3 Insert the battery pack.
*The battery must be correctly
oriented in relation to the terminals.
1 Open the monitor unit.
4 Close the battery cover.
Battery pack
2 Open the battery cover.
2
Insert the SD Memory Card.
h An SD Memory Card is not included with your camera. Please
purchase a commercially sold card.
h In this manual, the SD Memory Card is referred to as the “card”.
2 Insert the card.
1 Open the card slot cover.
3 Close the card slot cover.
English
Download from Www.Somanuals.com. All Manuals Search And Downlovadi.
Shooting
1
Press the ON/OFF button
for at least 1 second to turn
the camera on.
ON/OFF button
MENU button
h If the screen to set the
date and time appears,
press the MENU button 2
times to cancel it.
For how to set the date
2
Record.
To record a video clip:
h Press the [
] button to
begin recording a video
clip.
h Press the [
again to end the
recording.
] button
[
]
button
To take a photo:
h Press the [
] button.
h A still image is captured.
[
]
button
8
M
Full-HD
15
000:00:17
vii English
Download from Www.Somanuals.com. All Manuals Search And Download.
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i
Sanyo declines any claim for compensation for recorded contents etc. in case
of photographing or recording failure due to a chance camera or card flaw.
Playback
1
Press the REC/PLAY
button.
The display changes to
the Playback Screen.
REC/PLAY
button
h
2
Select the image to play
back.
h Use the arrow keys to
move the orange frame
to the image you wish to
play back.
SET button
h The image information
for the framed image is
shown in the bottom part
of the monitor.
3
Press the SET button.
h Playback begins.
<To return to the
recording mode>
h Press the REC/PLAY
button.
Deleting files
1
On the screen in step 2,
move the orange frame to
the file you wishtodelete,
and press the MENU
button.
100-0006
6.5MB
00:00:05
Full-HD
OK
Remaining battery
power indication
Orange frame
English viii
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
4
Select “DELETE”, and press the SET button.
Select “DELETE SINGLE”, and press the SET button.
Select “DELETE”, and press the SET button.
h If you press [G] or [H] , the screen to delete a different file will appear.
5
When you are finished deleting files, press the MENU button.
h Pressing the MENU button 3 times will return you to the screen in step
2.
When you are finished using the camera...
Press the ON/OFF button for at least 1 second to turn the camera off.
To continue to the next operation...
Please confirm that your computer is connected to the Internet.
ix English
Download from Www.Somanuals.com. All Manuals Search And Download.
Burn your recorded video clips onto a DVD
Using the supplied CD-ROM (Xacti Software CD), you can store your
captured images on a DVD.
Install application program
1
2
Set the supplied CD-ROM in your computer’s DVD drive.
h The installation window opens.
Click on [TotalMedia Extreme for SANYO].
h After clicking on the application program, follow the instructions shown
on the monitor to install the program.
h When the window appears requesting to restart your computer, click
the [Finish] button to reboot.
3
Remove the CD-ROM from the computer’s DVD drive.
<About the Kodak online service>
h When the installation window closes, a dialog box to connect to the
website introducing Kodak’s online service appears. Check the [No
thanks !] option button, and then click on the [OK] button.
English
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Copy data from your camera to the computer
Connect your camera to a computer, and copy the desired data to the
computer.
1
Turn on the computer, and use the supplied dedicated USB interface
cable to connect your camera to the computer.
h Connect the cable between the camera’s USB/AV terminal and the
computer’s USB connector.
2
h The USB Connection Screen appears on the camera’s monitor.
SET button
USB CONNECTION
COMPUTER
PRINTER
CANCEL
SET
CANCEL
OK
Terminal cover
Supplied dedicated
USB interface cable
To USB/AV terminal
on the camera
To USB connector
on the computer
xi English
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Select “COMPUTER”, and press the SET button.
h The screen to select the
computer connection mode
USB CONNECTION
CARD READER
MTP
appears.
SCREEN CAPTURE
PC CAMERA
CANCEL
OK
4
5
Select “CARD READER”, and press the SET button.
Copy data from your camera to a computer.
h The CD-ROM (Xacti Software CD) includes “TotalMedia Extreme for
SANYO” with which photo and video files can be imported en bloc.
HINT
How to open the terminal cover
English xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Burn video clips onto a DVD (for Windows Vista
users)
Here’s how to write your recorded data onto a DVD in the MPEG2 format. For
information on other operations, please see the Help file for TotalMedia
Extreme.
1
2
Insert a blank DVD in your computer’s DVD drive.
Double-click the desktop [TotalMedia Extreme for SANYO] icon.
h TotalMedia Extreme for SANYO is launched, and the startup page
appears.
[Create video] icon
xiii English
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Click the [Create video] icon.
h The TotalMedia Studio screen appears.
[New DVD project]
English xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Click [New DVD project].
h The screen to create a video clip to burn to DVD appears.
[Insert video]
xv English
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Click [Insert video].
h The screen to select the video clip file to burn to DVD appears.
h Click on the file you wish to burn to DVD.
h To select multiple files, keep the [Ctrl] key pressed while selecting
files.
Click the [Open] button.
h The files you selected in step 5 and the total size of the files to burn to
DVD are shown in the lower part of the window.
Selected files
Size of selected files
English xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Click the [Design] tab.
h The screen to design the title menu that is shown when the DVD is
played appears.
h Select one of the designs.
[Produce] tab
xvii English
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Click the [Produce] tab.
h The screen to burn files to the DVD appears.
[Burn] button
9
Click the [Burn] button.
h A window appears asking if you wish to save the project.
h Saving the project will save your settings from steps 5 through 7.
h It is recommended that you save the project if you intend to again edit
the same video clips that you burned to DVD.
English xviii
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
Click the [Yes] button.
h The screen to save the project appears.
h Assign a suitable file name for the project.
Click the [Save] button.
h The current project is saved, and the DVD burn process begins.
h When the burn process is completed, a window appears to inform you
that the process is done. Remove the DVD from the computer's DVD
drive.
12
13
14
Click the [OK] button.
h You are returned to the screen to burn files to DVD.
Click the [n] close button in the upper right corner.
h You are returned to the top page.
Click the [n] close button in the upper right corner.
h TotalMedia Extreme for SANYO is exited.
HINT
About software upgrades
i For information concerning TotalMedia Extreme upgrades, please go to the
following website:
h If TotalMedia Extreme is launched while you are connected to the
Internet, automatic program update notifications may appear.
To use Blu-ray Disc or AVCHD
i The version of TotalMedia Extreme that accompanies your camera cannot
be used to burn these formats. To purchase a different version, please
refer to the following website.
xix English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Does the window requesting confirmation to enable the MPEG-2 Codec
appear?
When using TotalMedia Extreme for the first time, a window requesting you to
confirm activation of the MPEG-2 Codec appears during the procedure. The
MPEG-2 Codec must be activated in order to burn files to a DVD. Complete
the following procedure to activate the MPEG-2 Codec.
i Note that your computer must be connected to the Internet in order to
complete this procedure. Please confirm that your computer is connected
to the Internet.
1 When the window requesting confirmation to activate the MPEG-2
Codec appears, click the [Yes] button.
h The ArcSoft website appears.
2 Click on [Special downloads].
h The window appears for you to enter your email address, name, license
ID, etc.
h Enter the correct information.
h The license ID is located on the back card of the supplied CD-ROM.
3 Click the [Submit] button.
h Soon thereafter, the URL for the download to activate the MPEG-2
Codec will be sent to the email address you entered in step 2.
4 Click the download URL link.
h The program will be downloaded to your computer.
5 Double-click the icon for the downloaded program.
h Follow the instructions to activate the MPEG-2 Codec.
h DVD burning via the TotalMedia Extreme program is now enabled.
h When the procedure above has been completed, continue to the
procedure to burn to DVD.
United States/Canada
Tel: +1-510-979-5599
content_page.asp?pageID=83
Hours: M-F from 9:00am - 5:00pm
(Pacific Standard Time, excluding holidays observed by ArcSoft)
Language: English
English xx
Download from Www.Somanuals.com. All Manuals Search And Download.
Europe
Tel: +353 (0) 61-702087
Email Support: [email protected]
Hours: M-Th from 8:30am - 5:30pm GMT
(excluding holidays observed by ArcSofts Affilitate)
F from 8:30am - 5:00pm GMT
(excluding holidays observed by ArcSoft’s Affilitate)
(Adjusted for daylight savings time when applicable)
Language: English, French, Italian, German, Spanish and Dutch
China
Tel: +86 (0) 571-88210575
E-Mail Support: [email protected]
Hours: M-F 8:30am-5:30pm
(Beijing local time) (excluding holidays observed by ArcSoft)
Language: Chinese
xxi English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Turning on the camera when the power save (sleep) mode
SWITCHING BETWEEN THE RECORDING MODE AND PLAYBACK
MODE .............................................................................................. 25
1
English
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery life .....................................................................................63
Possible No. of Images/Possible Shooting Time/
a test shot to confirm that your camera is set up and
English
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING THE INCLUDED ACCESSORIES
i Xacti Software CD (CD-ROM)
i Li-ion battery pack: 1
(page x): 1
i Lithium-ion battery pack
charger and power cord: 1
i Dedicated USB interface
i Dedicated AV interface cable
(page 43): 1
* To prevent from dropping the
camera, be sure to attach the
handstrap.
i GUIDE FOR BASIC
OPERATION
3
English
Download from Www.Somanuals.com. All Manuals Search And Download.
i SAFETY MANUAL
(safety precautions booklet)
Please read this booklet
carefully before using the
camera.
i QUICK GUIDE
English
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THE CARD
Media cards that can be used with this camera
The type of card that can be inserted into and used with this camera is:
i SD Memory Card
i SDHC Memory Card
i SDXC Memory Card
What “card” means in this manual
i In this manual, SD Memory Cards, SDHC Memory Cards and SDXC
Memory Cards that can be used in this dual camera are referred to as
“card”.
7
English
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
SETUP
PARTS NAMES
Front
LED light unit
i In contrast to a flash,
the LED light does
not emit a strong
Monitor unit
light. It is useful for
illuminating subjects
when taking macro
(close-up) shots.
Lens
Terminal cover
Stereo microphone
Battery cover
Bottom
Cover for DC adaptor (optional)
connection
Strap holder
Tripod stand hole
i Affix the camera to the tripod before opening the monitor unit.
i When closing the monitor unit, be sure to first detach it from the tripod.
English
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear
Monitor
ON/OFF button
Multi-indicator
Card slot cover
REC/PLAY button
MENU button
Arrow keys
[
] button
Photo shooting
button
SET button
Zoom switch
[T]/[W]
[
] button
Video recording
button
9
English
Download from Www.Somanuals.com. All Manuals Search And Download.
CHARGING THE BATTERY PACK
Please charge the supplied battery pack before using it.
1
Connect the supplied power
cord to the socket on the
battery pack charger.
h Insert the connector straight
and securely.
Battery pack charger
Power cord
Battery pack charger
2
Insert the battery pack in the
battery charger.
h Insert it in the direction
indicated by the [o] mark
on the battery pack.
Battery pack
[o] mark
CHARGE
indicator
To power outlet
3
4
Plug the power plug into a
power outlet (AC 100 V to
240 V).
h Charging begins.
h The CHARGE indicator is lit
during charging.
When the CHARGE indicator
turns off, unplug the power
cord from the power outlet,
and remove the battery pack
from the charger.
HINT
i Charging takes approximately 120 min.
English 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Charging the battery pack
Be sure to fully charge the supplied or separately sold battery pack before
using it in your camera. For charging the battery pack, use the supplied
charger.
Charge the battery pack if it is being used for the first time, and recharge it
whenever the remaining charge is low.
Does the battery pack feel hot?
i During charging, the charger and battery pack will be warm. This is normal
and does not indicate a malfunction.
If there is interference to your TV or radio during charging...
i Move the battery pack and charger further away from the TV or radio.
Ambient temperature during charging
i It is recommended that the ambient temperature during charging be
between about 10 °C and 35 °C (50 °F and 95 °F). Due to the
characteristics of the battery pack, at temperatures below 0 °C (32 °F), it
may not be possible to sufficiently charge it.
i When the battery pack temperature is high, the safety function may be
activated and halt charging.
Charge a battery pack in the following cases
i A battery pack which has not been used for a long time
i Newly purchased battery pack
FOR AMERICAN USERS:
i Use a UL Listed, 1.8 to 3 m (6 to 10 ft.), Type SPT-2 or NiSPT-2, AWG
No.18 power supply cord, rated for 125 V 7 A, with a non-polarized NEMA
1-15P plug rated for 125 V 15 A.
11 English
Download from Www.Somanuals.com. All Manuals Search And Download.
About the CHARGE indicator
The CHARGE indicator shows the status of the battery pack and the charger.
Please refer to the following table if the indicator flashes abnormally.
CHARGE indicator
Not lit
Not connected properly
i To recharge the battery pack, the power cord of the
charger must be connected to a power outlet, and the
plug at the other end inserted in the charger’s power
i The battery pack is not installed, or it is not installed
Charging finished
Lit
Charging
Flashing
Problem with the battery pack or battery pack charger
i Immediately remove the battery pack from the charger.
i Do not use an abnormal battery pack. (The usable life of
the battery pack has probably expired.)
CAUTION
Do not charge the battery pack immediately after the camera has been
in continuous use for a long time
i The battery pack becomes hot when the camera is used continuously for a
long time. If you attempt to charge the battery pack in this state, the safety
function may be activated and it may not be possible to charge the battery
pack. Wait until the battery pack has cooled down before attempting to
charge it.
English 12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE CARD
Be sure to format a newly purchased card or one that was used in another
used, the card itself may become unusable.
2 Insert the card.
3 Close the card slot cover.
1 Open the card slot cover.
<When removing the card...>
h To remove the card, press it in, and then release. The card will
protrude slightly, and you can then pull it out.
2 Push in,
then pull out
1 Open
13 English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Do not attempt to forcibly remove the card
i Doing so may damage the card or the stored files.
If the multi-indicator is flashing red...
i Never remove the card when the multi-indicator is flashing red, as doing so
may result in loss of files stored in the card.
HINT
To format a card
3 Press the MENU button.
4 Select the [E] tab, and press the SET button.
5 Select “FORMAT” and press the SET button.
i The Format Screen appears. Follow the instructions on the screen to
format the card.
Shooting without a card installed
i When a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played back
from the camera’s internal memory. When the camera is turned on with no
card installed, the internal memory icon
is shown on the monitor to let
you know that the images you capture will be saved to the camera’s
internal memory.
English 14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE BATTERY PACK
Please charge the supplied battery pack before using it.
3 Insert the battery pack.
*The battery must be correctly
oriented in relation to the terminals.
1 Open the monitor unit.
4 Close the battery cover.
Battery pack
2 Open the battery cover.
15 English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Does the battery pack appear swollen?
i The lithium-ion battery used in this camera may expand slightly when
stored in a hot environment or repeatedly used, but this is not a safety
hazard. However, a battery that is difficult to insert because it has become
swollen may then be impossible to extract from the battery compartment.
In this case, please discontinue its use and replace it with a new battery.
Do not use the battery with the outer covering or label removed
i Doing so may result in malfunction.
HINT
About the internal backup battery
i This camera’s internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the battery pack is kept in the camera continuously for about
2 days. In the fully charged state, the backup battery will maintain the
camera settings for about 7 days.
When not using the camera for a long time, remove the battery pack
i A small amount of power is still used even if the camera is turned off, and it
is therefore recommended that the battery pack be removed from the
camera if it is not going to be used for a long time. Note that when the
battery pack is removed for a long period, the time and date settings may
be cleared. Before using your camera again, be sure to confirm that the
camera settings are correct.
To prolong the life of the battery pack
i Although the battery pack is an expendable item, you can maximize the life
of the battery by heeding the following suggestions.
h Do not leave the battery under the hot summer sun or exposed to other
high-temperature environments.
h Do not continually recharge the battery when it is already fully charged.
After fully charging it once, for example, use it for a while to partially
discharge it before recharging it again.
h When the battery is not to be used for a long time, if possible store the
partially charged (not fully charged) battery in a cool environment.
17 English
Download from Www.Somanuals.com. All Manuals Search And Download.
About the temperature alert icon \
During camera use, if the temperature of the battery or inside the camera
(excluding the battery) rises, a temperature alert icon \will appear as
described below.
k When the battery or internal camera (excluding battery) temperature
rises during use
h During camera use, if the temperature of the battery or inside the
camera (excluding the battery) rises, a \icon lights on the monitor. It
is still possible to record and play back even when the \icon is lit;
however it is advised that you discontinue use as soon as possible and
turn the camera off.
h If the temperature rises further, the \icon will start to flash, and the
camera will turn off automatically.
The camera cannot be turned on until the temperature has dropped (or
as long as the \icon remains flashing). Please wait until the
temperature has dropped before resuming use.
h During video recording, a countdown indicator will show the time
starting about 15 seconds before shutdown. When the indicator shows
0 seconds, recording stops.
h If the camera is turned off while the temperature is high (that is, while
the \icon is flashing), it cannot be turned on again until the
temperature has dropped (or as long as the \ icon remains flashing).
English 18
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING THE CAMERA ON AND
OFF
Turning on the camera
1
Open the monitor unit, and press
the ON/OFF button for at least
1 second.
Monitor unit
h If you briefly press the ON/OFF
button, once, the camera will
switch to the power save mode.
ON/OFF button
Turning off the camera
1
Press the ON/OFF button for at least
1 second.
h The camera turns off.
ON/OFF
button
19 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning on the camera when the power save
(sleep) mode is active
In order to preserve battery pack power, the power save (sleep) function will
automatically turn off the camera after about 1 minute of no use during
shooting, or about 5 minutes of no use during playback (factory-preset
setting).
i When the power save mode is active, you can restore the power by any of
the following methods:
h Press the ON/OFF button.
h Press the [
] button.
h Open the monitor unit.
i After the power save mode has been active for about 1 hour, the camera
will switch to the standby mode. In this case, you can restore the power by
pressing the ON/OFF button, or by closing and then opening the monitor
unit.
i When the AC adaptor is connected, the power save mode will become
active about 5 minutes after the camera is turned on (factory-preset
setting).
i When the camera is connected to a computer or printer, the power save
mode becomes active after about 12 hours.
English 20
Download from Www.Somanuals.com. All Manuals Search And Download.
HINT
To immediately activate the power save mode
i Press the ON/OFF button briefly to activate the power save function.
About the standby mode
i To turn off the camera only briefly, you can close the monitor unit to put the
camera in the standby mode. The standby mode uses almost no power.
When the monitor unit is opened again, the camera turns on immediately
and you are ready to shoot or view images without any delay.
CAUTION
If the K icon appears...
i When a picture is taken, the date and time it was captured are recorded
the date and time cannot be recorded with the captured images. For this
reason, immediately after the camera is turned on, the “Set date and time”
reminder briefly appears, after which the K icon is shown on the
Recording Screen. To have the date and time recorded with the images,
please complete this setting before capturing images.
<Caution>
i Due to the characteristics of the camera, the outer surface may
become warm during use, but this does not indicate a malfunction.
i If the camera starts to feel uncomfortably hot during use, you might
temporarily discontinue use until it cools down, or try holding it in your
other hand for a while.
Please use a tripod or other support when using the camera for a
long time.
21 English
Download from Www.Somanuals.com. All Manuals Search And Download.
DATE AND TIME SETTING
The camera will record the date and time an image or audio recording is
taken so that you can display them during playback. Therefore, before
capturing images, make sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 24, 2010
1
and press the SET button.
h The Clock Set Screen appears.
h Follow the procedures below to
enable or disable the date
display during playback, to set
the display format for the date,
and to set the date and time.
h To display the Recording or
Playback Screen, press the
MENU button 2 times.
CLOCK SET
DATE
2010/02/01
00:00
TIME
DISP
D / M / Y
OK
2
Set the date.
1 Select “DATE”.
CLOCK SET
2 Press the SET button.
h The Set Date Screen
appears.
DATE
2010/12/24
3 Set the date to “2010/12/24”.
h The date is set in the
following order: Set the year
→ Set the month → Set the
day.
OK
h Press [G] or [H] to select
year, month or day. Press [I]
or [J] to increase or decrease
the number.
4 Press the SET button.
English 22
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Set the clock.
1 Select “TIME”.
2 Press the SET button.
h The Set Time Screen
appears.
3 Set the time to “19:30”.
h The time is set in the
following order: Set the hour
→ Set the minute.
h A 24-hour clock is used for
the time display.
4 Press the SET button.
CLOCK SET
TIME
19:30
OK
Set the order in which the date is
displayed during playback.
1 Select “DISP”.
CLOCK SET
2 Press the SET button.
h The Set Date Format Screen
appears.
DISP
D / M / Y
OK
3 Press [I] or [J].
h Press [I] to change the
displayed date order as
follows:
D / M / Y → Y / M / D → M / D / Y
Press [J] to change it in the reverse order.
4 Press the SET button.
23 English
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the MENU button.
h The date and time setting is completed.
h To display the Recording or Playback Screen, press the MENU button.
HINT
i Under normal conditions, while the battery pack is being replaced, an
internal battery will maintain the date and time settings. However, there is a
small chance the settings may be lost (the backup will last for about
7 days). It is recommended to check that the date and time settings are still
correct after replacing the battery pack and before shooting or recording of
any type (follow step 1).
To correct the date and time settings
1 Turn on the camera.
3 Select “CLOCK SET” and press the SET button.
h The screen to set the date and time appears.
h The current date and time settings are shown.
4 Select the line you wish to change, and make the correction.
English 24
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHING BETWEEN THE RECORDING
MODE AND PLAYBACK MODE
Switch between the recording mode (for recording) and the playback mode
(for viewing your recorded images).
1
2
Press the REC/PLAY button.
h The mode changes.
h The mode changes each time the REC/PLAY button is pressed.
8
M
Full-HD
15
000:00:17
REC/PLAY
button
<Example of the recording
mode>
2010.12.24
18:41
100-0006
00:00:05
SD
6.5MB
Full-HD
OK
<Example of the playback
mode>
25 English
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHING THE OPERATING MODE
The “SIMPLE mode” comprises only those functions that are most often used
and necessary to operate the camera, while the “NORMAL mode” enables
full use of all the camera’s many functions. Select the mode that is suitable for
your purposes.
Switching between the SIMPLE and NORMAL
modes
1
2
3
h The previous mode is active.
Press the MENU button.
h The Menu Screen for the active mode appears.
Select the operating mode icon,
and press the SET button.
h Switch from the SIMPLE mode
to the NORMAL mode, or from
the NORMAL mode to the
Switch to detailed
SIMPLE mode.
h Press the MENU button to
cancel the Menu Screen.
normal menu
OK
S
N
Operating mode icon
<SIMPLE Mode Menu Screen>
1
2
3
Press SET button to
1
switch to simple Menu
2
3
OK
S
N
Operating mode icon
<NORMAL Mode Menu Screen>
English 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessing/exiting the SIMPLE/NORMAL Mode
Menu Screen
1
2
3
If the Menu Screen is not displayed, press the MENU button.
h The Menu Screen appears.
h To cancel the Menu Screen, press the MENU button.
Switch to detailed
normal menu
S
N
OK
<Example: SIMPLE Mode
Recording Menu>
1
2
3
MENU
button
Press SET button to
1
switch to simple Menu
2
3
S
N
OK
<Example: NORMAL Mode
Recording Menu>
27 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIMPLE Mode Menu
4
Press [I] or [J] to select the item you wish to change, and press the
SET button.
h The Setting Screen for the selected item appears.
Select an item to change
Description of selected item
Press [I]
Select video and photo size
S
N
OK
Press [J]
To keep in HDTV size
8
M
2
M
Press
HDTV size
8
M
[4:3]
OK
<Setting Screen>
English 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the NORMAL Mode Menu
4
Press [I] or [J] to select a tab.
h The Menu Screen for the selected tab appears.
Tab
Press [I]
RECORDING MENU1
1
2
3
VIDEO
Full-HD
PHOTO
8
M
SCENE SELECT
FILTER
1
2
3
LED LIGHT
SELF-TIMER
OK
S
N
Press [J]
Option tab
5
Press [H].
RECORDING MENU1
VIDEO
1
Fu8ll-HD
M
2
3
Press [H]
PHOTO
SCENE SELECT
FILTER
1
2
3
LED LIGHT
SELF-TIMER
OK
29 English
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Press [I] or [J] to select the item you wish to change, and press the
SET button.
h The Setting Screen for the selected item appears.
h To return to the Menu Screen, press the MENU button.
Select an item to
change
RECORDING MENU
VIDEO
1
Press [I]
1
2
3
F8ull-HD
M
PHOTO
SCENE SELECT
FILTER
1
2
3
LED LIGHT
SELF-TIMER
OK
Applicable mode
Press [J]
PHOTO
3264x2448
3328x1872[16:9]
8
6M
M
-
Press
2048x1536
2048x1536
3
3M H
M
S
-
2288x1288[16:9]
1920x1080[16:9]
3
2M
M
SET
OK
<Setting Screen>
HINT
About the applicable mode indicator
i This indicator shows the shooting mode(s) for which the selected setting is
effective.
: This setting is effective during still image shooting.
: This setting is effective during video clip recording.
: This setting is effective during still image shooting and video clip
recording.
English 30
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOTING
SHOOTING
VIDEO CLIP RECORDING
1
and set it to the recording
[
]
2
Press the [
h Recording begins.
] button.
button
h It is not necessary to keep the
[
] button pressed while
recording.
h When the remaining recording
time available for the currently
recording clip becomes little, a
countdown of the remaining
recording time appears on the
display.
Recording time
3
End the recording.
2
M
Full-HD
h Press the [
] button again
RERCEC00000::0000::0099
to stop recording.
55
Available recording
time remaining
31 English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOTING SINGLE SHOTS
Capture a still image (single-shot).
1
2
and set it to the recording
[
]
button
Press the [
1 Press the [
halfway.
] button.
] button
h The autofocus operates,
and the image is focused
(focus lock).
2 Continue to gently press
the [
way.
] button all the
h The shutter releases and
the image is captured.
h You can view the captured
image on the monitor by
keeping the [
] button
depressed when you
capture the image.
8
M
1
2
Target mark
English 32
Download from Www.Somanuals.com. All Manuals Search And Download.
HINT
Adjusting the monitor brightness
i While the Recording Screen is active, you can quickly access the screen
for adjusting the brightness of the monitor by pressing the MENU button for
at least 1 second.
What is the camera focusing on?
i A target mark & on the monitor
Target mark
shows the area the camera is
3
M-S
focusing on.
i The camera automatically
determines the correct focus by
measuring from 9 different focus
points within the shooting area. If the
target mark is at a position that is
different from the point you wish to
focus on, you can refocus, for
example, by changing the shooting
angle.
F2.8
1/2
Camera shake icon
Shutter speed
Aperture
i The large target mark appears when
the camera focuses on a wide area
in the center of the screen.
The focus and exposure can be locked (in the NORMAL mode)
the autofocus or the exposure to a fixed setting. When the exposure setting
is fixed, the P icon appears on the monitor; when the autofocus setting
is fixed, the picon appears on the monitor.
the focus lock is released.
The shutter speed and aperture are displayed (in the NORMAL mode)
i The shutter speed and aperture settings are shown on the Recording
Screen. You can use them as a reference when shooting.
If the camera shake icon > appears... (in the NORMAL mode)
i During still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, the
camera shake icon may appear on the monitor. In this case, use a tripod to
stabilize the camera when shooting.
i When shooting with the scene select function set to the fireworks +
mode, the camera shake icon always appears, but this is normal.
Does it seem to take a long time to save images?
i When shooting in dimly lit conditions, it may take some time to save the
data to the card.
33 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the LED light
The LED light can be used for macro photography to illuminate close-up
subjects in dimly lit surroundings.
1
light setting, and press the SET button.
h The screen to select the LED light operation appears.
LED light on
Use dimly lit conditions
OK
1: The LED light operates regardless of the shooting conditions.
0: The LED light is disabled regardless of the shooting conditions.
2
3
Select the desired LED light operation, and press the SET button.
h This completes the LED light operation setting.
Press the [
] button to take the picture or the [
] button to
begin recording.
English 34
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
Is the recorded image dark?
i In contrast to a flash, the LED light does not emit a strong light. It is useful
for illuminating subjects when taking macro (close-up) shots.
i When the LED light is used, the edges of the captured image may appear
dark.
Do not touch the LED light unit when shooting
i The LED light becomes very hot and may cause a burn. Avoid touching the
LED light when shooting.
HINT
About using the LED light
i The LED light turns off after about 8 minutes.
i A video clip using the LED light continuously can be recorded for about 8
minutes. About 30 seconds before recording ends, a countdown display is
shown in the monitor.
able to change the LED light mode from the Recording Screen (in the
NORMAL mode).
35 English
Download from Www.Somanuals.com. All Manuals Search And Download.
SHOOT A STILL IMAGE WHILE
RECORDING A VIDEO CLIP
You can capture a still image (a single-shot) while recording a video clip.
1
Turn on the camera
(page 19), and set it to the
[
]
button
2
3
Press the [
] button.
[
]
When you see a scene
you’d like to capture as a
still image, press the
button
[
] button.
4
Press the [
end the video clip
recording.
] button to
2
M
Full-HD
RERCEC00000::0000::0099
English 36
Download from Www.Somanuals.com. All Manuals Search And Download.
HINT
i When the remaining video recording time becomes approximately
50 seconds, it will no longer be possible to capture a still image while
recording a video clip. The exact remaining recording time at which this
occurs will differ depending on the subject and on the recording size
intend to capture a still image while recording a video clip, it is suggested
that you take note of the remaining video recording time.
About the recording size of still images
i The size of a still image captured during video clip recording depends on
the video clip recording size.
Video clip recording size setting
Still image recording size
+
,
[
!Y
"&
)
h It is not possible to capture a still image when recording a video clip in the
x mode.
h It is not possible to capture sequential shots.
37 English
Download from Www.Somanuals.com. All Manuals Search And Download.
MACRO-PHOTOGRAPHY (ZOOM)
Your camera has two zoom functions: optical zoom and digital zoom.
1
2
Point the camera lens at the
subject.
Push the zoom switch toward
[T/]] or [W/P] to compose
the desired image.
Zoom switch
[T/]]: Zoom in on the subject.
[W/P]: Zoom out.
h When the zoom switch is
pushed, the zoom bar appears
on the monitor.
h When the optical zoom factor
is at maximum, zooming stops
temporarily. When the zoom
switch is pushed toward the
[T/]] side again, the mode
changes to the digital zoom
mode and zooming continues.
Monitor
3
Take the picture.
For video clip recording, see
For shooting single shots, see
For shooting sequential shots,
Zoom bar
When both
optical and digital
zoom are enabled
Optical zoom
Digital zoom (yellow)
Pointer
When optical
zoom only is
enabled
English 38
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
PLAYBACK
PLAYING BACK VIDEO CLIPS AND
STILL IMAGES
1
2
Select the image to play back.
Orange frame
h Use the arrow keys to move
the orange frame to the file
you wish to play back.
h The image information for the
framed image is shown at the
bottom of the screen.
2010. 12.24 18:41
100-0006
00:00:05
SD
6.5MB
Full-HD
3
Press the SET button.
h The image you selected in
step 2 is displayed fullscreen.
h If a video clip was selected,
playback begins.
OK
<To return to the screen to
select playback files>
Press [J].
Arrow keys
SET button
39 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Video clip playback operation
To do this...
Do this
Normal forward playback Press the SET button.
Stop playback
During playback, press [J].
During playback, press the SET button or
press [I].
Pause
During accelerated playback, press [I].
To play back
one image
at a time
(single-
Forward
playback
After pausing playback, press [H].
Reverse
playback
After pausing playback, press [G].
frame step)
Forward
playback
After pausing playback, press and hold [H].
Slow
playback
Reverse
playback
After pausing playback, press and hold [G].
During forward playback, press [H].
h The playback speed changes each time [H]
is pressed, as follows:
Forward
playback
Normal playback → 2× → 5× → 10× → 15×
Press [G] to resume normal playback speed.
To
accelerate
playback
During forward playback, press [G].
h The playback speed changes each time [G]
is pressed, as follows:
Reverse
playback
15× ← 10× ← 5×
Press [H] to resume normal playback speed.
Return to normal playback
speed
Press the SET button.
Louder: During playback, push the zoom
switch toward the [T] side.
Softer: During playback, push the zoom
Adjusting the volume
switch toward the [W] side.
HINT
If the a appears on the playback Screen...
English 40
Download from Www.Somanuals.com. All Manuals Search And Download.
How to save one frame from a video clip as a
still image
1
2
Play back the video clip. Pause the playback at the point you wish to
“snap” a photo.
Press the [
h The screen to select the aspect ratio of the still image appears. Select
the desired aspect ratio, and press the [ ] button. Note, however,
that if the video clip aspect ratio is 4:3, you cannot select 16:9.
] button.
HINT
The file size for a video clip is very large
i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fast
enough, making it appear jerky. (The video will always be displayed
properly on the camera monitor or a television.)
i Depending on the card, recording may end even before the possible
recording time indicated.
Display the video clip playback point
i During video clip playback, press the MENU button for at least 1 second to
display a bar showing the current playback point in the video clip.
i Press the MENU button for about 1 second to cancel the bar.
CAUTION
During video clip playback, the sound of a motor is audible...
i During recording, the sound of the optical zoom movement or autofocus
movement was recorded. This is not a malfunction.
If no audio is heard...
i The audio is not played back when the video clip is played back in the
frame-by-frame, slow-motion, fast playback or reverse playback mode.
41 English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING TO A TV
CONNECTING TO A TV
CONNECTING TO A TV
By connecting the camera to a TV, you can play back the recorded files on the
TV.
CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
About image output: The image output destination differs depending on the
camera status.
Recording mode
Standby Recording
Connection
cable
Image output
destination
Playback
mode
n
NTSC:
PAL: m
Camera monitor
TV
n
m
m
n
Dedicated AV
interface cable
NTSC: m
PAL: n
Camera monitor
TV
n
m
n
HDMI cable
m
n
m
m: Images are output n: Images are not output
HINT
i HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
English 42
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a video input terminal
Use the supplied dedicated AV interface cable to connect to a TV.
Set the input to
“VIDEO”.
Supplied dedicated
AV interface cable
To USB/AV
terminal
Yellow plug:To Video Input terminal
White plug: To Audio Input (L) terminal
Red plug: To Audio Input (R) terminal
Connecting to the HDMI terminal
Use a separately sold mini-HDMI cable to connect to a TV.
Set the input to
“HDMI”.
Mini HDMI cable
(optional)
To HDMI terminal on
the TV
To HDMI
terminal
43 English
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING BACK ON A TV
i After connecting the camera to the television, switch the TV input to the
terminal to which the camera is connected.
i The playback method is the same as when viewing images on the
camera’s monitor. (Use the TV controls to adjust the volume.)
i The same playback procedure as when playing back with the camera is
used to play back audio recordings as well.
CAUTION
Insert and pull out the cable carefully
i When connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on the
devices. Push the plugs in straight when connecting them. If undue force is
used to connect a cable, it may permanently damage the connector pins in
the terminal socket.
i Do not use excessive force when connecting and disconnecting cables.
English 44
Download from Www.Somanuals.com. All Manuals Search And Download.
OBTAINING THE INSTRUCTION MANUAL
OBTAINING THE INSTRUCTION MANUAL
OBTAINING THE INSTRUCTION
MANUAL
The Instruction Manual that explains the features in detail can be downloaded
from our website.
i “Adobe Reader” is required to view the Instruction Manual. If Adobe
Reader is not already installed on your computer, a link to the website from
which you can download it can be found on our website.
Contents of the Instruction Manual
Explanations for the functions indicated below can be found in the
downloadable Instruction Manual.
Please be sure to obtain and use the Instruction Manual.
HOW TO READ THIS MANUAL
QUICK SEARCH BY OPERATION
CHECKING THE INCLUDED ACCESSORIES
How to use the accessories
ABOUT THE CARD
Media cards that can be used with this camera
What “card” means in this manual
GETTING THE MOST OUT OF YOUR CAMERA
High-quality images with “Full High Definition*”
Includes SIMPLE mode for quick-and-easy operation
Image stabilizer for sharp pictures
Capture clear images of the targeted subject
Eye-Fi smart
SYSTEM MAP
SETUP
PARTS NAMES
CHARGING THE BATTERY PACK
Charging the battery pack
INSTALLING THE CARD
INSTALLING THE BATTERY PACK
Installing the DC adaptor (sold separately: VAR-A3U/A3EX)
About the temperature alert icon \
TURNING THE CAMERA ON AND OFF
Turning on the camera
Turning off the camera
Turning on the camera when the power save (sleep) mode is active
DATE AND TIME SETTING
45 English
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHING BETWEEN THE RECORDING MODE AND PLAYBACK MODE
SWITCHING THE OPERATING MODE
Switching between the SIMPLE and NORMAL modes
Accessing/exiting the SIMPLE/NORMAL Mode Menu Screen
Overview of the SIMPLE Mode Setting Screen
Overview of the NORMAL Mode Setting Screen
SIMPLE
SHOOTING
BEFORE TAKING PICTURES
For best results
Using the autofocus
Select the recording size
Select the focus setting
Hints for taking pictures
VIDEO CLIP RECORDING
SHOOTING SINGLE SHOTS
Using the LED light
SHOOT A STILL IMAGE WHILE RECORDING A VIDEO CLIP
MACRO-PHOTOGRAPHY (ZOOM)
PLAYBACK
PLAYING BACK VIDEO CLIPS AND STILL IMAGES
How to save one frame from a video clip as a still image
SLIDESHOW PLAYBACK
PLAYBACK VOLUME
DELETING FILES
Delete single/delete all/delete folder
Delete selected
PLAYBACK MODES
21-image display playback
Selecting the playback folder
Magnifying (zooming in) the image
NORMAL
SHOOTING
RECORDING MENU 1
Video setting
Still image setting
Scene select setting
Filter setting
Self-timer setting
RECORDING MENU 2
Motion compensation (image stabilizer) setting
Focus range setting
English 46
Download from Www.Somanuals.com. All Manuals Search And Download.
Focus mode setting
Light-measuring mode setting
ISO sensitivity setting
RECORDING MENU 3
White balance setting
Exposure setting
Subject chaser settings
High sensitivity mode setting
Digital zoom setting
Exposure compensation
Storage folder setting
PLAYBACK
PLAYBACK MENU 1
Slideshow settings
File protect setting
Resize
Rotate
PLAYBACK MENU 2
Correcting the image
Editing video clips
Printing instructions
FILE INFO DISPLAY
OPTION SETTINGS
DISPLAY THE OPTION SETTING MENU
INTRODUCTION TO THE OPTION SETTING MENU
Shortcut setting
TV output setting
File No. continued setting
Formatting (initializing)
CHECKING THE REMAINING CARD MEMORY
Checking the remaining number of images and video recording time
For audio recordings
CHECKING THE REMAINING BATTERY PACK CHARGE
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TV
CONNECTING TO A TV
Connecting to a video input terminal
Connecting to the HDMI terminal
PLAYING BACK ON A TV
CONNECTING TO A PRINTER
PRINTING
47 English
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDICES
COMMONLY ASKED QUESTIONS
TROUBLESHOOTING
Camera
Notes regarding the Scene Select feature and filters
SPECIFICATIONS
Camera
Camera connectors
Battery life
Possible No. of Images/Possible Shooting Time/Possible Recording Time
Concerning the multi-indicator
Supplied battery pack charger
Supplied Li-ion battery pack
Others
Before capturing those important shots, be sure to first take a test shot to
confirm that your camera is set up and ready to go
HINTS FOR TAKING PICTURES
English 48
Download from Www.Somanuals.com. All Manuals Search And Download.
How to obtain the Instruction Manual
The Instruction Manual that explains the camera functions in detail can be
obtained from the SANYO website.
1
2
Insert the supplied Xacti Software CD in your computer's CD drive.
On the installation screen, click [Go to Xacti CS1 Web Support
Page].
3
Follow the instructions on the screen to download the Instruction
Manual.
h “Adobe Reader” is required to view the Instruction Manual.
Adobe Reader can be found in the Xacti Software CD.
49 English
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THE EYE-FI TRANSFER FEATURE
ABOUT THE EYE-FI TRANSFER FEATURE
ABOUT THE EYE-FI TRANSFER
FEATURE
By inserting a commercially sold Eye-Fi card (SD card with wireless LAN) in
your camera, you can easily upload photos to your computer, a sharing site,
etc. automatically via a Wi-Fi network. Also, you can transfer video files if your
Eye-Fi card has a video upload function. The Eye-Fi card settings can be
performed using the Eye-Fi Manager, but in addition, the settings below can
be performed with this camera.
i Eye-Fi automatic transfer ON/OFF
i Automatic halt of Eye-Fi operation when battery is low
i AC adaptor connection restrictions (may or may not be supported,
depending on the camera)
i SSID setup/delete
HINT
i The Instruction Manual for the Eye-Fi transfer feature can be obtained from
*
“Adobe Reader” is required to view the Instruction Manual. Adobe
Reader can be found in the Xacti Software CD.
English 50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDICES
APPENDICES
COMMONLY ASKED QUESTIONS
If you have a question about the camera operation, you might find the answer
in this compilation of commonly asked questions.
Question
Answer
Action
Why doesn’t the
power turn on?
Due to cold
temperatures, the your pocket to warm
battery pack
temporarily lost its
power.
Place the camera in
it up before using it.
Why is the battery The ambient
Keep the battery
pack in an
environment of 10 to
40 °C (50 to 104 °F).
pack consumed
so quickly even
after it was fully
recharged?
temperature is
very low.
The battery pack
life has expired.
If a battery becomes
depleted quickly even
after it was sufficiently
charged, it should be
assumed that the
Power
battery has reached
the end of its service
life. Please replace it
with a new battery.
Why doesn’t
recharging end?
The battery pack
life has expired.
Replace with a new
battery pack. If this
is not effective,
consult your dealer.
Why does the
The remaining
battery pack
power is low.
Use the AC adaptor,
and DC adaptor
(optional) or replace
the battery pack with
a fully charged one.
icon
appear?
Why does the
Shooting multi-indicator
A recorded file is
being saved on
the card.
Not a malfunction.
Wait until the multi-
indicator turns off.
flash red?
51 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
Action
Are the settings
retained even
after the camera
is turned off?
—
All settings except
the self-timer and
the exposure
compensation are
retained even after
the camera is turned
off.
Which resolution
setting should I
use?
—
Select the resolution
setting according to
the intended use.
J, ], y, z,
", R, $:
Appropriate for
printing letter-size or
larger, and for
Shooting
printing a close-up
of part of a photo
(trimming).
+, G: For
printing standard
photo (photo
service) sizes.
,, [: For
photos displayed on
a web page, or sent
as e-mail
attachments.
English 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
What is the
difference
Answer
—
Action
Because shooting
with the optical
between the
digital zoom and
the optical zoom?
zoom uses the
optics of a physical
lens, you can shoot
without losing
minute details in the
image. The digital
zoom, on the other
hand, works by
magnifying a portion
of the image that
hits the image
sensor and may
produce a coarser
image.
Shooting
How can I get the
distant view into
focus?
—
Set the scene select
function to the
landscape +
mode when
photographing.
Or, set the focus
range setting to
manual focus -,
and set the distance
to ∞.
53 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
Action
When used in
cold weather, why the monitor
does the image
seem to leave
traces as it
Condition due to
Not a malfunction.
Spots that appear in
the monitor only
appear in the
monitor and will not
be recorded with the
images.
characteristics.
moves?
Monitor
Why does the
displayed image
contain some red,
blue and green
dots, or why are
black spots
visible?
Why is the image The subject was
too bright? too bright.
When capturing an
image, devise a way
to compensate for a
bright subject, for
example, by
changing the
shooting angle.
Viewing
images
Why is the image The focus is not
out of focus? locked properly.
Hold the camera
correctly and slowly
press the [
]
button halfway to
lock the focus. Then
press the [
]
button all the way to
capture the image.
English 54
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
This may happen Play back images
when trying to that were recorded
play back images on a card using this
Action
Why is there no
image (z is
shown)?
stored on a card
from a different
digital camera.
camera.
Viewing
images
Why is the
playback image
distorted?
If the subject
Not a malfunction.
This is a
characteristic of the
CMOS sensor.
moves or the
camera is moved
during recording,
a distorted image
may sometimes
occur.
55 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
Due to the
characteristics of
the camera,
Action
Not a malfunction.
Why isn’t the
magnified image
clear?
magnified images
appear less clear.
Why isn’t the
captured image
clear?
The image was
captured using
the digital zoom.
Not a malfunction.
Viewing
images
Can I play back
image and sound
files that I edited
using my
—
We cannot
guarantee the
accurate playback of
files that have been
edited using a
computer.
computer?
Why is there a
motor-like sound
during video clip
playback?
The sound of the
camera’s
mechanical action
was recorded.
Not a malfunction.
Why is there no
sound?
The volume on
the TV is set to
the minimum.
Adjust the volume
on the TV.
Connecting
to a TV
Why does a
message appear
during PictBridge printer.
printing?
There is a
problem with the
Please refer to the
instruction manual
for your printer.
Printing
English 56
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
You have
attempted to join
video clips having resolution or frame
different
Action
Select video clips
that have the same
The “Cannot edit
video clips with
unlike settings”
message
rate.
appears.
resolutions or
frame rates.
Why is a noise
heard from a
nearby TV or
radio during
battery
Electromagnetic
waves are emitted adaptor further away
from the charger.
Move the AC
from the TV or radio
when recharging the
battery pack.
recharging?
Why does the
“Insufficient card
memory” or
There is no more
available memory files, or use a card
on the card or in
the camera’s
Delete unnecessary
that has more
memory available.
“Insufficient
internal memory”
message appear?
internal memory.
Misc.
Why does the
“Card is
protected”
The lock switch on Move the lock switch
the card is in the
locked (protect)
to the unlocked
position.
message appear? position.
Why can’t the
camera be
operated?
A temporary
Remove the AC
internal circuitry
problem may be
the cause.
adaptor and the
battery pack from
the camera, wait a
few minutes, then
reinstall the battery
pack and try again.
A problem such
as inability to
record or play
back occurs.
The card contains After saving your
files that were
saved using a
files to a different
medium, format the
device other than card.
this camera.
57 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Question
Answer
Action
Can I use my
camera abroad?
—
When the camera is
connected to a TV,
you can switch the
camera’s video
output to NTSC or
PAL. If you have
questions about
accessories etc.,
please consult with
a dealer near you for
advice.
Why does the
“System error”
message appear? the camera or
card.
A problem has
occurred within
Check the following
items:
1 Remove the
card and then
install it again.
2 Remove the
battery pack and
then install it
Misc.
again.
3 Install a different
card.
If “System error” still
appears after
performing the
above steps, then
take the camera to
the dealer for
service.
English 58
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Camera
Recorded image
file format
Still images:
JPEG format (DCF, DPOF, Exif 2.2 compliant)
Note: Designed mainly by the Japan Electronics
and Information Technology Industries
Association (JEITA), DCF (Design rule for
Camera File system) is standard for digital
still camera image files to provide
interoperability between digital photography
devices for the images stored on removable
memory cards. However, it is not
guaranteed that all devices will support the
DCF standard.
Video clips:
Conforms to ISO-standard MPEG-4 AVC/H.264*
Audio:
MPEG-4 audio (AAC compression)
48 kHz sampling rate, 16-bit stereo format
Data storage
media
Internal memory: Approx. 50 MB
SD Memory Card
SDHC Memory Card (up to 32 GB)
SDXC Memory Card (up to 64 GB)
Image sensor/
camera effective
number of pixels
1/5-inch (0.5 cm) CMOS sensor
Still images: Approx. 3.3 million pixels
Videos (HD mode): Approx. 2.8 million pixels
Videos (SD mode): Approx. 3.3 million pixels
* Video clip files recorded with models VPC-CA65 and VPC-CG65 are in
the same H.264 format as this model. However, such files cannot be
played back, since they are not compatible due to differences such as the
data compression method.
59 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Still image
J: 3264 × 2448 pixels (approx. 8 million pixels)
]: 3328 × 1872 pixels (approx. 6 million pixels,
16:9 aspect ratio)
y: 2048 × 1536 pixels (approx. 3 million pixels,
low compression)
shooting mode
(recording
resolution)
z: 2048 × 1536 pixels (approx. 3 million pixels,
normal compression)
": 2288 × 1288 pixels (approx. 3 million pixels,
16:9 aspect ratio)
+: 1920 × 1080 pixels (approx. 2 million pixels,
16:9 aspect ratio)
G: 1600 × 1200 pixels (approx. 2 million pixels)
,: 1280 × 720 pixels (approx. 900,000 pixels, 16:9
aspect ratio)
[: 640 × 480 pixels (approx. 300,000 pixels)
R: 3264 × 2448 pixels (approx. 8 million pixels,
sequential shots)
$: 2048 × 1536 pixels (approx. 3 million pixels,
sequential shots)
Video clip
!: 1920 × 1080 pixels, 60 fields/s (60i)
Y: 1920 × 1080 pixels, 30 fps (30p)
": 1280 × 720 pixels, 60 fps (60p)
&: 1280 × 720 pixels, 30 fps (30p)
x: 960 × 540 pixels, 30 fps (30p)
recording mode
(recording
resolution)
): 640 × 480 pixels, 30 fps (30p)
h The 60 fps frame rate of this camera is 59.94 fps,
and the 30 fps frame rate is 29.97 fps.
White balance
Lens
Full-auto TTL; manual setting available
Focal length: f = 3.2 mm to 28.8 mm, Optical 9×
zoom
Open: F = 2.8 (wide) to 3.0 (tele)
9 groups, 12 elements (including three with six
aspheric surfaces)
Galvanometer iris
Internal ND filter
35 mm film camera conversion
Still image shooting: 38 mm to 342 mm
(9× optical zoom)
Video clip recording: 38 mm to 380 mm
(10× advanced zoom)
English 60
Download from Www.Somanuals.com. All Manuals Search And Download.
Exposure control
type
Programmable AE/Shutter speed priority AE/
Aperture priority AE/Manual exposure control
Exposure compensation available (0 1.8 EV in
0.3 EV steps)
Light-measuring
mode
Multi-section measuring, center-weighted
measuring, spot measuring
Range
Normal mode:
50 cm (19.69 in.) to infinity
Super macro mode:
1 cm (0.39 in.) to 1 m (3.28 ft.) (wide end only)
Digital zoom
Shutter speed
For shooting:
1× to approx. 10×
For playback:
1× to 51× (varies with resolution)
Still image shooting mode: 1/2 to 1/1,000 sec.
(Maximum approx. 1 sec. when scene select
function set to lamp Q)
Sequential shots mode: 1/15 to 1/1,000 sec.
Video clip recording mode: 1/30 to 1/10,000 sec.
(1/15 sec. max.: when scene select function is set
to the lamp Qor high sensitivity mode)
Sensitivity
Still image shooting (standard output sensitivity*)/
video clip recording mode:
Auto
Still image shooting
LED light off: ISO 50 to 400
LED light on: ISO 50 to 800
Video clip recording: ISO 50 to 800
ISO 50, 100, 200, 400, 800, 1600
(Switchable from the Recording Menu)
*
Sensitivity measured in compliance with the ISO
standard (ISO 12232:2006).
*
Maximum ISO sensitivity up to 1600 equivalent
when Scene Select function is set to Q.
Minimum subject
illumination
Approx. 15 lux (1/30 sec in the scene select AUTO
mode)
Approx. 4 lux (1/15 sec in the lamp or HIGH
SENSITIVITY mode)
Image stabilizer
Video: Electronic
Still image: Multi-calculation electronic
61 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor
2.7" (6.9 cm) low-temperature polysilicon TFT color
wide liquid crystal (transmissive), approx.
230,000 pixels
Built-in flash
No
LED light working
range
Approx. 10 cm (3.94 in.) to 1 m (3.28 ft.)
Super macro mode (wide side only)
LED light modes
Focus
ON, OFF
TTL-type AF (still image shooting mode: 9-point
range finder/spot focus; video clip recording mode:
Continuous focus), manual focus
Self-timer
Approx. 2-second delay, 10-second delay
Ambient
environment
Temperature
0 to 40 °C (32 to 104 °F) (operation)
–20 to 60 °C (–4 to 140 °F)
(storage)
Humidity
30 to 90% (operating, no
condensation)
10 to 90% (storage, no
condensation)
Power supply
Battery pack
(supplied)
Li-ion battery pack (DB-L80) ×1
AC adaptor
(optional)
VAR-G9
For use with DC adaptor (VAR-A3:
sold separately)
Power consumption
3.5 W (When using the Li-ion
battery during recording)
Dimensions (excluding protrusions) 62.5 (W) × 26.8 (D) × 123.5 (H) mm
2.46 (W) × 1.06 (D) × 4.86 (H) in.
(Maximum dimensions)
Volumetric capacity: Approx. 126 cc
Weight
Approx. 142 g (5.0 oz.) (camera
only [without battery pack and
card])
Approx. 159 g (5.6 oz.) (including
battery pack and card)
English 62
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera connectors
USB/AV
Dedicated regrouped jack
(communication/audio
and video output)
terminal
Audio
output
Stereo
Video
output
Composite video, NTSC color TV
system/PAL TV system (switchable
from the Option Setting Menu)
USB
USB 2.0 High Speed
PC camera: USB video class
HDMI terminal
Video output
Total number of scan lines (effective
number of scan lines): 750p (720p)/
1125i (1080i)/525p (480p)
Audio output: L-PCM 48 kHz sampling
Battery life
Shooting
Still image
shooting mode
Approx. 200 images:
CIPA standard (when a SanDisk
2 GB SD Memory Card is used)
Video clip
recording mode
Approx. 60 minutes:
Recorded in ! mode
(When LED light is OFF)
Approx. 70 minutes:
Recorded in Y mode
(When LED light is OFF)
Playback
Approx. 210 minutes:
Monitor on, continuous playback
i Until battery pack runs out when using a fully charged battery pack at a
25 °C (77 °F) ambient temperature.
i The operation time may vary depending on the conditions of the battery
pack and the conditions of use. Especially when used at temperatures
below 10 °C (50 °F), the battery pack operation time is significantly
reduced.
63 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Possible No. of Images/Possible Shooting Time/
Possible Recording Time
Shooting/
recording
mode
SD Memory Card
Resolution
setting
Internal
Memory
8 GB
16 GB
J
]
y
z
"
+
G
,
[
R
$
!
Y
19 images
24 images
32 images
48 images
51 images
2,960 images
3,770 images
4,980 images
5,940 images
7,560 images
9,980 images
7,320 images 14,600 images
7,780 images 15,600 images
Still image
mode
71 images 10,800 images 21,700 images
76 images 11,300 images 22,700 images
142 images 20,700 images 41,600 images
327 images 49,800 images 99,800 images
19 images
48 images
22 sec.
2,960 images
5,940 images
7,320 images 14,600 images
1 hr. 1 min.
1 hr. 21 min.
1 hr. 21 min.
1 hr. 46 min.
42 min.
2 hr. 4 min.
2 hr. 43 min.
2 hr. 43 min.
3 hr. 33 min.
1 hr. 24 min.
8 hr. 39 min.
29 sec.
29 sec.
Video clip
mode
"
&
x
)
38 sec.
15 sec.
1 min. 34 sec.
4 hr. 19 min.
Audio
recording
mode
<
26 min. 10 sec.
67 hr.
134 hr.
i If the continuous recording time of a voice memo exceeds about 13 hours,
the recorded file is saved once, and then recording continues in a new file.
In the video clip recording mode, when the size of the file being recorded
exceeds 4 GB, the recorded file is saved once, and then recording
continues in a new file. (These 4 GB segments are automatically created.
The recording session continues until you stop recording, but voice memo
recording is temporarily interrupted while the file is being saved.)
i The above values apply when an SD Memory Card by SanDisk is used.
i Even with cards of the same capacity, the amount of data that can actually
be stored may differ depending on the card brand, etc.
i The continuous shooting time for each video clip will differ depending, for
example, on the card capacity, environmental conditions (temperature and
shooting conditions, etc.).
English 64
Download from Www.Somanuals.com. All Manuals Search And Download.
Concerning the multi-indicator
The camera’s multi-indicator will light, flash, or be off, depending on the
different camera operations.
Multi-indicator
Multi-indicator
status
Color
Green
Orange
Camera status
Connected to a
computer or
printer
Lit
Power save
mode active
Flashing
Lit
Connected to a
TV
Rise in internal
temperature
Slow
During self-
Flashing Fast timer
photography
Red
Very
fast
Accessing card
65 English
Download from Www.Somanuals.com. All Manuals Search And Download.
Supplied battery pack charger
Part No.
VAR-L80
Power source
Rated output
Compatible batteries
AC 100 to 240 V, 50 to 60 Hz, 5 W
DC 4.2 V, 550 mA
Supplied or separately sold Lithium-ion
battery pack (DB-L80)
Ambient
environment
Temperature
Humidity
0 to 40 °C (32 to 104 °F) (when charging)
–20 to 60 °C (–4 to 140 °F) (storage)
20 to 80% (no condensation)
Dimensions
84.0 (W) × 50.5 (D) × 22.5 (H) mm
3.31" (W) × 1.99" (D) × 0.89" (H)
Weight (without power cord)
Approx. 49 g (1.7 oz.)
i When using the supplied battery pack charger abroad, the power cord may
need to be replaced in accordance with local requirements. Please contact
your local dealer for details.
Supplied Li-ion battery pack
Model number
Voltage
DB-L80
3.7 V
Capacity
700 mAh
Ambient
environment
Temperature 0 to 40 °C (32 to 104 °F) (during use)
–10 to 30 °C (14 to 86 °F) (storage)
Humidity
10 to 90% (no condensation)
Dimensions
Weight
39.2 (W) × 31.4 (D) × 5.9 (H) mm
1.54 (W) × 1.24 (D) × 0.23 (H) in.
Approx. 15 g (0.5 oz.)
English 66
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Mac OS is a trademark of Apple Inc., registered in the U.S. and other
countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in
the USA and other countries.
Intel and Pentium are registered trademarks of Intel Corporation (USA).
In this manual, the Microsoft® Windows® 2000 operating system, Microsoft®
Windows® XP operating system, Microsoft® Windows® Vista operating
system, and Microsoft® Windows® 7 operating system are collectively
referred to as “Windows”.
Software Red Eye by FotoNationTM 2003-2005 is a trademark of FotoNation®
Inc.
Red Eye software© 2003-2005 FotoNation In Camera Red Eye - covered by
U.S. Patent No. 6,407,777. Other patents Pending.
SDXC logo is a trademark.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
Eye-Fi is a registered trademark of Eye-Fi, Inc.
All other company and product names are registered trademarks or
trademarks of their respective owners.
67 English
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
i It is forbidden to copy this manual, whole or in part, without prior written
permission.
i All images and illustrations given in this manual are for explanation
purposes and may differ slightly from that of the actual product. Also,
actual specifications are subject to change without prior notice and
therefore may differ from the contents of this manual.
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
i Sanyo Electric shall not be held responsible for any problems resulting
from the use of this camera.
i Sanyo Electric declines all responsibility for damages due to improper use
of the camera, failure to adhere to the instructions given in this manual, or
repairs or changes done by those other than a technician authorized by the
manufacturer.
i Sanyo Electric shall not be held responsible for any damage caused by
optional devices or consumable items used with the camera other than
those supplied with the camera or those specified by Sanyo Electric.
i Sanyo Electric shall not be held responsible for any losses or loss of
revenue resulting from the loss of data caused by the malfunction, or the
repairing of a malfunction, of the camera.
i The images captured with this camera will differ in quality from pictures
taken with a standard film camera.
English 68
Download from Www.Somanuals.com. All Manuals Search And Download.
SANYO Electric Co., Ltd.
Download from Www.Somanuals.com. All Manuals Search And Download.
|