Sansui Flat Panel Television SLED4280 User Guide

OWNER’S MANUAL

GUIDE D’UTILISATION

42/46” CLASS WIDE LED TV

TÉLÉVISEUR DEL GRAND ÉCRAN CATÉGORIE 42/46 PO

SLED4280

SLED4680

ATTENTION

If you purchase a universal remote control from your local retailer, please contact the remote manufacturer for the

required programming code.

Si vous utilisez avec cet appareil une télécommande universelle (autre que celle vendue avec ce téléviseur),

consultez la documentation accompagnant la télécommande universelle afin de connaître le code numérique cor-

respondant au téléviseur.

AIR/CABLE MODE SELECTION

SÉLECTION DU MODE AIR/CABLE

When shipped from the factory, the Signal Type option is set to the “Cable” (Cable Television) mode.

If not using Cable TV, set this menu option to the “Air” position.

Lorsque l’appareil sort de l’usine, l’option Signal Type est en mode « Cable » (câblodistribution). Si vous

n’utilisez pas la câblodistribution, sélectionnez l’option « Air ».

IF CONTACT WITH CUSTOMER SERVICE IS REQUIRED

PLEASE HAVE THE MODEL NUMBER READY PRIOR TO THE CALL.

S’IL FAUT CONTACTER LE SERVICE CLIENTÈLE, PRENEZ SOIN D’ÊTRE MUNI

DU NUMÉRO DE MODÈLE AVANT D’APPELER.

CUSTOMER SERVICE – 1-800-289-0980

SERVICE/SERVICE CLIENTÈLE: 1-800-289-0980

ORION WEBSITE

SITE WEB ORION

FOR INFORMATION ON OUR OTHER PRODUCTS AND RECYCLING INFORMATION, PLEASE VISIT OUR WEBSITE AT

POUR OBTENIR DES INFORMATIONS SUR NOS AUTRES PRODUITS ET LE RECYCLAGE, VEUILLEZVISITER NOTRE SITE WEB:

www.orionsalesinc.com

Before operating the unit, please read this manual thoroughly.

Avant de faire fonctionner l’appareil, veuillez lire le présent guide attentivement.

Download from Www.Somanuals.com. All Manuals Search And Download.

15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as

vases, should not be placed on the apparatus.

16) An outside antenna system should not be located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touching such power lines or

circuits, as contact with them might be fatal.

17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.

18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points

or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into

the unit.

19) If an outside antenna or cable system

is connected to the unit, be sure the

antenna or cable system is grounded

to provide some protection against

voltage surges and built-up static

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE

ANTENNA LEAD IN WIRE

GROUND

CLAMP

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

charges, Section 810 of the National

Electrical Code, ANSI/NFPA 70, provides

information with respect to proper

grounding of the mast and supporting

structure, grounding of the lead-in

wire to an antenna discharge unit, size

of grounding conductors, location of

antenna discharge unit, connection to

ELECTRIC SERVICE

EQUIPMENT

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

S2898A

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

grounding electrodes, and requirements for the grounding electrode.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

20) When replacement parts are required, be sure the service technician uses replacement parts

specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

21) Upon completion of any service or repairs to this unit, ask the service technician to perform safety

checks to determine that the unit is in proper operating condition.

22) When you connect the product to other equipment, turn off the power and unplug all of the

equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal

injury. Read the owner's manual of the other equipment carefully and follow the instructions when

making any connections.

23) Sudden high volume sound may cause hearing or speaker damage. When you use headphones,

(if the unit is equipped with a headphone jack) keep the volume at a moderate level. If you use

headphones continuously with high volume sound, it may cause hearing damage.

24) Do not allow the product to output distorted sound for an extended period of time. It may cause

speaker overheating and fire.

25) This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the

NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground

shall be connected to the grounding system of the building, as close to the point of cable entry as

practical.

26) The socket-outlet must be installed near the unit and easily accessible.

CHILD SAFETY:

It Makes A Difference How and Where You Use Your Flat Panel Display

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE ISSUE

The home theater entertainment experience is a growing trend and larger flat panel displays are popular

purchases. However, flat panel displays are not always supported on the proper stands or installed

according to the manufacturer’s recommendations.

Flat panel displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers,

chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

The consumer electronics industry is committed to making home entertainment enjoyable and safe.

TUNE INTO SAFETY

One size does NOT fit all. Follow the manufacturer’s recommendations for the safe installation and use of

your flat panel display.

Carefully read and understand all enclosed instructions for proper use of this product.

Don’t allow children to climb on or play with furniture and television sets.

Don’t place flat panel displays on furniture that can easily be used as steps, such as a chest of drawers.

Remember that children can become excited while watching a program, especially on a “larger than life” flat

panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or

knocked down.

Care should be taken to route all cords and cables connected to the flat panel display so that they cannot be

pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:

Use a mount that has been recommended by the display manufacturer and/or listed by an independent

laboratory (such as UL, CSA, ETL).

Follow all instructions supplied by the display and wall mount manufacturers.

If you have any doubts about your ability to safely install your flat panel display, contact your retailer about

professional installation.

Make sure that the wall where you are mounting the display is appropriate to support the weight of the unit/

product and wall mount. If you are unsure, contact a professional installer.

A minimum of two people are required for installation. Flat panel displays can be heavy.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

CONDENSATION

Moisture will form in the operating section of the unit if the unit is brought from cool surroundings into a warm

room or if the temperature of the room rises suddenly. When this happens, unit's performance will be impaired.

To prevent this, let the unit stand in its new surroundings for about an hour before switching it on, or make sure

that the room temperature rises gradually.

Condensation may also form during the summer if the unit is exposed to the breeze from an air conditioner. In

such cases, change the location of the unit.

HOW TO HANDLE THE LCD PANEL

• Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.

• If the LCD panel is broken, make absolutely sure that you do not touch the liquid in the panel. This may cause

skin inflammation.

If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your

eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water.

Possible Adverse Effects on LCD Panel: If a fixed (non-moving) pattern remains on the LCD Panel for

long periods of time, the image can become permanently engrained in the LCD Panel and cause subtle but

permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your

LCD Panel on for long periods of time while it is displaying the following formats or images:

• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on

a normal (4:3) display (black bars at top and bottom of screen); or viewing normal style (4:3) media on a

widescreen (16:9) display (black bars on left and right sides of screen).

The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim any

responsibility for these symptoms.

• LCD Panels are manufactured using an extremely high level of precision technology, however sometimes

parts of the screen may be missing picture elements or have luminous spots.

This is not a sign of a malfunction.

• Do not install the LCD Panel near electronic equipment that produces electromagnetic waves. Some

equipment placed too near this unit may cause interference.

• Effect on infrared devices – There may be interference while using infrared devices such as infrared cordless

headphones.

SAFETY PRECAUTIONS

The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause overheating.

Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When placing on a shelf leave 10 cm

(4 inches) free space around the entire unit.

10cm

Notes when mounting the LCD TV on a wall

•

If the unit is to be mounted on the wall, contact the retailer where

you purchased the LCD TV for advice, and have the equipment

professionally installed. Incomplete or improper installation may

cause injury to you, and/or damage to the LCD TV.

Bracket holes:To attach a wall mounting bracket (not supplied) attach

where indicated in the drawing right.

•

This manufacturer recommends professional installation.

Utilize an appropriate bracket and fasteners, sufficient to

accommodate the size and weight of the unit.

Bracket holes

•

Assure the wall to which the unit is to be mounted will safely support

the size and weight of the unit, using the bracket and fasteners you

have selected.

•

Keep cords and cables connected to this flat panel display out of

reach of children.

To hang the television on a wall, remove these screws and then

remove a stand. Before performing work spread cushioning over the

base area to lay the TV on.

Illustration is SLED4280

Screws

Download from Www.Somanuals.com. All Manuals Search And Download.

How to attach the stand

NOTE:

• Unplug the AC cord from the AC outlet.

• Ensure that unpacking and transfer of the unit is carried out by two or more people.

• Before beginning this process, assure that the TV is laid on a clean, safe, and cushioned surface to avoid

any damage to the unit.

• Do not touch or press the TV-screen, glass might break under pressure.

Place the TV on its front onto a table.

Align the stand’s bottom-plate (supplied) as seen here.

It will ﬁt in only one direction.

Hold the unit and attach the stand slowly, as shown in Figure 1.

LCD PANEL SIDE

Figure 1

Illustration is SLED4280

Figure 2

Finally secure the bottom-plate with 4 screws (supplied) as indicated by the arrows in Figure 2.

• Be sure to follow the instructions. Insufficient tightening or incorrect installation of the stand will not support

your unit correctly, and could result in damage or injury from tip-over.

How to remove the stand

When you transport this product, remove the stand and pack ﬂat against the back of the unit in the carton. To

remove the stand, perform these steps in reverse order.

For wall mounting, the base must be removed. To disconnect the base/stand remove the 4 screws from the back

(see page 5).

Download from Www.Somanuals.com. All Manuals Search And Download.

Features

• LED Backlight System - It realize thin profile, low power consumption, eco-friendly Hg-less design and high

contrast picture.

• Integrated Digital Tuner - You can view digital broadcasts without using a Digital TV Set-Top Box.

• Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for

hearing impaired viewers.

• Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control

adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.

• Programmable TV Sleep Timer - Operable from the remote control, the LCD TV can be programmed for up

to 120 minutes to turn off automatically.

• V-Chip - The V-Chip function can read the rating of a broadcast program or movie content if the program is

encoded with this information. V-Chip will allow you to set a restriction level.

• Digital Audio Jack (Coaxial) - When a component with a built-in Dolby Digital decoder is connected, Dolby

Digital sound can produce the effect of being in a movie theater or a concert hall.

• HDMI/Component Video Jacks - A VCR, DVD player, satellite receiver or other audio/video component can

be connected to this unit.

• On-Screen 3 Language Display - You can select one of 3 languages, English, French or Spanish for on-

screen programming.

* Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of

Dolby Laboratories.

* HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.

Power source

TO USE AC POWER

Connect the AC cord into an AC outlet.

AC Outlet

AC 120V, 60Hz

AC cord

Illustration is SLED4280

NOTE:

• Please make sure to insert the cord securely the wall outlet.

• The AC cord has a grounding-type AC line plug. If the supplied AC cord does not match you AC outlet,

contact a qualified electrician, do not defeat the purpose of a grounding plug.

WARNING:

• DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC

CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.

CAUTION:

• WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF

SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET.

• DO NOT PLUG/UNPLUG THE AC CORD WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL

SHOCK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Before using your unit

IMPORTANT SAFETY INSTRUCTIONS...........3

SAFETY PRECAUTIONS .................................5

How to attach the stand ....................................6

How to remove the stand ..................................6

Features............................................................7

Power source....................................................7

Contents ...........................................................8

Parts and functions ...........................................9

Remote control ...............................................10

Antenna connections ......................................11

Cable TV connections.....................................11

Connections to other equipment.....................12

TV operation

Starting setup .................................................15

TV operation ...................................................15

Quick guide for menu operation......................16

Convenience functions ...................................17

Memorizing channels......................................18

Checking the digital signal strength ................19

Labeling channels...........................................19

Labeling video inputs......................................19

Setting the V-Chip ...........................................20

Closed Caption...............................................21

CC advanced..................................................21

Setting the picture size....................................22

Additional information

Reception disturbances ..................................23

Troubleshooting ..............................................24

Specifications ................................................25

limited WARRANTY ........................................26

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts and functions

Front

Illustration is SLED4280 Right side

HDMI1/DVI IN jack

FOR SERVICE PERSONNEL USE ONLY

Do NOT insert ANY USB device into

this port. Use of this port by other

than Service Personnel may void this

products warranty.

VIDEO 1 IN jacks

(VIDEO/AUDIO

(L(MONO)/R))

Power Indicator

Red : Standby

Blue : On

Remote sensor

VOL (VOLUME) +/– buttons

CH (CHANNEL) buttons

(POWER) button

INPUT/ENTER button

MENU button

To display the menu screen :

Touch MENU button to display the menu screen.

CH (CHANNEL)

buttons, VOL (VOLUME) +/– buttons and INPUT/ENTER button can be used to select the

desired setting during the menu screen operations.

To adjust the TV angle :

You can adjust the TV angle of the TV-screen for 30° from horizontal angle. Hold the base of the TV while adjusting

the angle.

PC MONITOR IN jack

Illustration is SLED4280

Rear

COMPONENT

IN jacks

PC/DVI AUDIO IN jack

HDMI2 IN jack

VIDEO 2 IN jacks

(VIDEO/AUDIO

(L(MONO)/R))

HDMI3 IN jack

VAR. (VARIABLE)

AUDIO OUT jacks

DIGITAL AUDIO

COAXIAL OUT jack

RF (ANT.) IN jack

Service connector cover: Please do not open this cover. There is a socket only for service purpose inside.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

6.CURSOR ▲/▼/◀/▶ Buttons - Used to operate

the menu functions of the LCD TV.

7.ENTER Button - Use to enter or select

information for On-Screen operations.

8.MUTE Button - To turn off the sound, press this

button once. The LCD TV will be silenced and

the symbol “Mute” will appear on the screen. The

muting feature can be released by pressing the

MUTE button again or one of the VOL (VOLUME)

+ or – buttons.

9.VOL (VOLUME) + / – Buttons - Press the +

button to increase, or the – button to decrease the

sound level.

10.INPUT SELECT Button - Use to change the

external input.

11.CCD Button - Used to display the Closed Caption

menu screen.

12.SLEEP Button - To set the LCD TV to turn off

after a preset amount of time, use the SLEEP

button on the remote control.

13.PICTURE SIZE Button - Used to change the

1. (POWER) Button - Used to turn the power

picture size.

on/off to the LCD TV.

14.RECALL Button - This button allows you to go

back to the previous channel selected by just

pressing the RECALL button. Press this button

again to return to the channel you were watching.

2.DISPLAY Button - When you press this button,

the current information will be displayed on a

screen. To remove the display from the screen,

press this button again.

15.EXIT Button - Press to remove setup menu.

16.AUDIO Button - Change soundtrack language.

3.Direct Channel Selection Buttons (0-9) - Allows

direct access to any channel of the LCD TV.

17.CH (CHANNEL)

Buttons - To change the

4.– Button -This button is the “–” button used when

channels of the LCD TV.

selecting digital channels.

5.MENU Button - Use to display the On-Screen

menu function.

Before using the remote control, batteries must first be installed.

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.

Use two “AAA” size batteries (supplied). The batteries

may last approximately one year depending on

how much the remote control is used. For best

performance, it is recommended that batteries should

be replaced on a yearly basis, or when the remote

operation becomes erratic. Do not mix old and new

batteries or different types.

BATTERY PRECAUTIONS

2. Install two “AAA” batteries (supplied).

3. Replace the battery compartment cover.

These precautions should be followed when using

batteries in this device:

• Use only the size and type of batteries specified.

• Be sure to follow the correct polarity when

installing the batteries as indicated in the battery

compartment. Reversed batteries may cause

damage to the device.

• Do not mix different types of batteries together (e.g.

Alkaline and Carbon-zinc) or old batteries with fresh

ones.

• If the device is not to be used for a long period of

time, remove the batteries to prevent damage or

injury from possible battery leakage.

• Do not try to recharge batteries not intended to be

recharged; they can overheat and rupture. (Follow

battery manufacturer’s directions.)

Download from Www.Somanuals.com. All Manuals Search And Download.

Antenna connections

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your

antenna system. If you are using a Cable TV service, see “Cable TV connections”.

Combination VHF/UHF Antenna (Single 75 ohm cable)

Antenna

Connect the 75 ohm cable from the combination

VHF/UHF antenna to the antenna jack.

Jack

75 ohm

Coaxial

Cable

Cable TV connections

This TV has an extended tuning range and can tune most cable channels without using a Cable TV

Converter box. Some cable companies offer “premium pay channels” where the signal is scrambled.

Descrambling these signals for normal viewing requires the use of a descrambler device which is

generally provided by the Cable TV company.

For subscribers to basic Cable TV service

For basic Cable TV service not requiring a Converter/

75 ohm

Descrambler box, connect the 75 ohm Coaxial Cable directly

Coaxial

Cable

Antenna

Jack

to the Antenna Jack on the back of the TV.

For subscribers to scrambled Cable TV service

If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect

the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial

Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the TV. Follow the

connections shown below. Set the TV to the output channel of the Converter/Descrambler box (usually channel

3 or 4) and use the Converter/Descrambler box to select channels.

Incoming

75 ohm

Cable TV

Cable

Antenna

Jack

75 ohm Cable to TV

Converter/

Descrambler

For subscribers to unscrambled Cable TV service with scrambled premium

channels

If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require

the use of a Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available

from the Cable TV company or an electronics supply store). Follow the connections shown below. With the

switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the

“A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the

Converter/Descrambler box to tune scrambled channels.

Incoming

Converter/

75 ohm

Cable TV

Cable

Antenna

Jack

Descrambler

75 ohm Cable to TV

A/B Switch

Splitter

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections to other equipment

The exact arrangement you use to interconnect various video and audio components to this unit is dependent

on the model and features of each component. Check the Owner’s Manual provided with each component for

the location of video and audio inputs and outputs.

To connect the LCD TV to a VCR

Right of the unit

VCR

To Video/Audio OUT

To VIDEO/AUDIO IN

Video/Audio cord (not supplied)

To connect the LCD TV to a DVD player with Component Video Input

You can enjoy a high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks of your DVD

player with the COMPONENT video cables (not supplied).

Rear of the unit

Component video cord

(not supplied)

To COMPONENT IN

To Component OUT

DVD

To Audio OUT

To AUDIO IN

Audio cord

(not supplied)

NOTE:

• Component Video input of the unit are for use with a device which output 480i/1080i interlaced signals and

480p/720p progressive signals.

To connect the LCD TV to a camcorder, or a TV Game

To playback from a camcorder, connect the camcorder to the unit as shown.

This unit can also be used as a display device for many video games. However, due to the wide variety of

signals generated by these devices and subsequent hook-up variations required, they have not all been

included in the suggested connection diagrams.You’ll need to consult each component’s Owner’s Manual for

additional information.

Right of the unit

To VIDEO/AUDIO IN

Video/Audio cord (not supplied)

To Video/Audio OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections to other equipment

(continued)

To connect an audio system

This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the

TV’s remote control.

To control the audio, turn on the TV and the stereo amplifier, and turn off the TV’s built-in speakers (see page 17).

Rear of the unit

Amplifier

To VAR. AUDIO OUT

To Audio (L) Input

To Audio (R) Input

Audio cord (not supplied)

NOTE:

• To hear sound when using an external audio amplifier, the volume of both the TV and the amplifier must be set

above 0 (zero).

• For example, if the volume of the TV is set to 0, you will not be able to hear any sound, even if the volume of the

amplifier is at its highest level.

Using an AV Amplifier with built-in digital surround

If you are using an Amplifier with built-in digital surround sound, you can enjoy various audio systems including

Dolby Digital Surround audio that sounds just like the movie.

Connect an AV amplifier with built-in Dolby Digital decoder, etc. as shown below.

Front

Speaker

Rear of the unit

Subwoofer

(Right)

Front

Speaker

(Left)

To DIGITAL AUDIO

COAXIAL OUT

Coaxial digital cable

(not supplied)

Center Speaker

To Coaxial

Digital Audio IN

Surround

Speaker (Left)

Surround

Speaker

(Right)

AV Amplifier with built-in digital surround

decoder as listed above

NOTE:

• When you are viewing digital broadcast, this unit will not work in conjunction with DTS audio or MPEG audio.

There will be no sound output if connected to an AV amplifier with a built-in DTS decoder or MPEG decoder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections to other equipment

(continued)

To connect the LCD TV to a HDMI or a DVI device to the unit

The HDMI1/DVI input receives digital audio and uncompressed video from a HDMI device or uncompressed

digital video from a DVI device.

When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate

analog audio cords required.

To DVI output

Right and rear of the unit

Audio cord (not supplied)

To PC/DVI

AUDIO IN

DVI device

HDMI device

To HDMI out

HDMI - to - DVI adapter cable

To HDMI IN

(HDMI type A connector)

(not supplied)

HDMI cable (type A connector)

(not supplied)

NOTE:

• When using HDMI1/DVI to connect your HDMI or DVI devices, you must select the corresponding

audio input source (HDMI or DVI) on the menu screen (see page 17). Otherwise you will only see the

image with no sound.

To connect the LCD TV to a PC (Personal Computer)

Before you connect this TV to your PC, change the adjustment of your PC’s Resolution and

Refresh rate (60 Hz).

Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA

connector PC MONITOR IN on the rear of the TV. Attach the connectors firmly with the screws on the plug. In case

of a Multimedia computer, connect the audio cord to the audio output of your Multimedia computer and to the

AUDIO connector of the PC/DVI AUDIO IN jack of the TV.You can also connect the PC with HDMI cable. If you

use HDMI cable, you don’t have to connect the audio cord. If you use DVI-to-HDMI cable, please connect audio

cord as same way as VGA cable.

Press INPUT SELECT on the remote control to select PC mode.

Switch on the computer. The TV can operate as the computer monitor.

Right and rear of the unit

Monitor Display modes

MODE Resolution Refresh rate

VGA

640x480 60/ 72/ 75 Hz

720x400 70Hz

SVGA 800x600 56/ 60/ 72/ 75 Hz

XGA 1024x768 60/ 70/ 75 Hz

WXGA 1280x768 60Hz

WXGA 1280x720 60Hz

WXGA 1360x768 60Hz

SXGA 1280x1024 60Hz

WXGA+ 1440x900 60Hz

To PC

MONITOR

To PC/DVI

AUDIO IN

VGA cable (not supplied)

To HDMI IN

Audio cord (not supplied)

HDMI cable (not supplied)

FHD

1920x1080 60Hz

To return to normal mode

Press INPUT SELECT again.

NOTE:

• The on-screen displays will have a different appearance in PC mode than in TV mode.

• If there is no video signal from the PC when the unit is in PC mode, “No signal” will appear on the TV-screen.

• When the PC connected to the HDMI terminal and 1920x1080 resolution (FHD) is selected, the top and

bottom, right and left edges of the picture may be hidden on all PICTURE SIZE. In this case, use the PC

MONITOR IN jack (VGA cable) is recommended to connect.

• When the PC’s resolution is set to 1920 x 1080/60 Hz (FHD mode), a signal that differs from the FHD signal,

which has been confirmed operational on this TV, may appear depending on the PC used. In this case, “Auto

Adjust” or other Position Adjustment functions may fail to correct the image position.

To solve this problem, change the PC settings to select another resolution.

Download from Www.Somanuals.com. All Manuals Search And Download.

Set the Signal Type option to the appropriate

position (see “Air/Cable selection” on page 18).

Starting setup

The Auto Setup menu appears the first time you

turn on the TV, and assists you to specify the

Air/Cable setting, and program your channels

automatically.

Press the Direct Channel Selection (0-9, –)

buttons to select the channel.

(If you press only channel number, channel

selection will be delayed for a few seconds.)

TO SELECT ANALOG CHANNELS

IMPORTANT: Make sure that the antenna or cable

TV system connection is made!

1-9:

Press 1-9 as needed. Example, to select

channel 2, press 2, then press ENTER.

Press the 2 digits in order. Example, to

select channel 12, press 1, 2, then press

ENTER.

10-99:

To turn on the TV, press (POWER) (POWER

indicator on the front of the unit changes blue. It

may take approx. 10 seconds for a picture to appear

on screen.).The Auto setup function begins.

100-135: Press the 3 digits in order. Example, to

select channel 120, press 1, 2, 0, then press

ENTER.

Auto Setup

TV Location

Store

Cable

Start

TO SELECT DIGITAL CHANNELS

Signal Type

Automatic Search

Press the first 1-3 digits, then press the – button,

followed by the remaining number.

This unit has been preset to STORE brightness

This setting does not qualify under ENERGY

STAR.To reduce brightness and energy

consumption, change setting to ‘HOME’. This

setting does qualify under ENERGY STAR.

Example, to select channel 15-1, press 1, 5, –, 1,

then press ENTER.

: Select

: Adjust

• If a channel is selected with only audio content,

“Audio only” will be displayed on the screen.

• If a channel is selected with a weak digital

signal, “Digital channel signal strength is low”

will be displayed on the screen.

Press ▲ or ▼ to select “TV Location”, then press

◀ or ▶ to select “Store” or “Home”. This product

qualifies for ENERGY STAR in Home mode

default setting.

The same program may be available on either

an analog channel or a digital channel.You may

choose to watch either format.

NOTE:

• This unit has been preset to STORE brightness.

This setting does not qualify under ENERGY

STAR.To reduce brightness and energy

consumption, change setting to ‘HOME’.This

setting does qualify under ENERGY STAR.

• The device may not conform to the ENERGY

STAR standard after Reset is performed or the

Backlight is adjusted.

• If a channel is selected to which you have not

subscribed, “Digital channel is encrypted” will

be displayed on the screen.

VHF/UHF/CABLE CHANNELS

Air

Cable

VHF

2-13

UHF

STD/HRC/IRC

(A) (W)

Press ▲ or ▼ to select “Signal Type”, then press

14-69

14-36

37-59

60-85

86-94

95-99

100-135

(AA) (WW)

◀ or ▶ to select “Cable” or “Air”.

(AAA) (ZZZ)

(86) (94)

(A-5) (A-1)

(100) (135)

(4A)

Press ▲ or ▼ to select “Automatic Search”, then

press ▶ or ENTER.

NOTE:

Now the “Auto Setup” starts. After the auto setup

is completed, the TV channel appears on the

screen.

• If a channel with no broadcast is selected, the

sound will automatically be muted.

• It may take a few seconds for a digital channel

picture to appear on screen after being selected.

•

Depending on the reception condition, it may

take from 15 minutes to 30 minutes to complete

memorizing digital cable channels. Please be patient.

To select the video input source

To view a signal from another device connected to

your LCD TV, such as a VCR player, press INPUT

SELECT, then press ▲ or ▼ or corresponding

Number buttons (0-7), then press ENTER.You

can select TV, Video1, Video2, Component, HDMI1,

HDMI2, HDMI3 or PC depending on which input jacks

you used to connect your devices.

NOTE:

• If you press EXIT in the process of “Auto Setup”,

the Auto Setup stops and changes to the normal

screen.

• When you make a menu selection, your changes

occur immediately.You do not have to press EXIT to

see your changes.

Input Select

0.TV

1.Video1

2.Video2

3.Component

4.HDMI1

5.HDMI2

6.HDMI3

7.PC

TV operation

To turn on the TV, press (POWER).

(POWER indicator on the front of the unit

changes blue. It may take approx. 10 seconds for

a picture to appear on screen.)

[0-7]:Select

_PC_rH_{ess and release CH}

. The channel automatically

Adjust the volume level by pressing VOL (VOLUME)

stops at the next channel set into memory.

For proper operation, before selecting channels, they

should be set into the memory. See “Memorizing

channels” on page 18.

+ or – . The volume level will be indicated on

the screen by blue bars. As the volume level

increases, so do the number of bars. If the

volume decreases, the number of blue bars also

decreases.

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY

Quick guide for menu

operation

Press DISPLAY to display the current information on

the screen.

When the TV receives a digital signal, the digital

information will appear.

Call menu and for example: Select Language.

Sleep Timer

Off

English

62-1 HDTV Moving Picture1

CH-1 TV-MA

Digital Air

Press INPUT SELECT to select TV mode.

No Program Information is available

Press MENU. The TV menu screen will appear.

Main Menu

Full

1080i

Picture

Audio

Channel

Lock

• Channel number

• Channel label (if preset) • Broadcast program name

• V-Chip rating

• Sleep timer

• Program guide

• Resolution

• Station name

Setup

• Signal type

• Audio language

• Picture size

: Select

ENTER:Set

Press ▲ or ▼ to select “Setup”, then press ▶ or

ENTER.

Press ▲ or ▼ to select “Language”, then press

When the TV receives an analog signal, the analog

information will appear.

◀ or ▶ to select the desired language.

…on the following pages the menu can be called

Sleep Timer

Off

Analog Cable

in the same way as here.

Press EXIT to return to the normal screen.

Mono

Full

NOTE:

480i

• If no buttons are pressed for more than about 60

seconds, the menu screen will return to normal

operation automatically.

• Channel number

• V-Chip rating

• Channel label (if preset)

• Signal type

• Sleep timer

• Picture size

• Audio information

• Resolution

(Stereo, SAP or Mono)

Press DISPLAY again to clear the call display.

NOTE:

• After a few seconds, DISPLAY screen will return to

normal TV-operation automatically.

RECALL

This button allows you to go back to the last channel

selected by pressing RECALL. Press RECALL again to

return to the last channel you were watching.

MUTE

Press MUTE to switch off the sound. The TV’s sound

will be silenced and “Mute” will appear on the screen.

The sound can be switched back on by pressing this

button again or the VOL (VOLUME) + or –.

SLEEP

To set the TV to turn off after a preset amount of time,

press SLEEP on the remote control. The clock will

count up 10 minutes for each press of the SLEEP but-

ton (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep

time is programmed, the display will appear briefly

every ten minutes to remind you that the sleep timer

is operating. To confirm the sleep timer setting, press

SLEEP and the remaining time will be displayed for a

few seconds. To cancel the sleep timer, press SLEEP

repeatedly until the display turns to Off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Convenience functions

You can change the default settings by pressing the MENU button on your remote, then select one of the icons

at the left of the menu - follow the On-Screen prompts to set your preferences.

Icon

Picture Picture

Selected Items

Setup hint

Brightness / Contrast You can adjust the picture quality to your preference.

Setting

/ Sharpness / Color

/ Tint

Color Temperature Bluish (Cool) / Neutral (Standard) / Reddish (Warm)

Backlight

The Backlight feature adjusts the screen brightness for improved picture clarity.

DBC

On / Off

Use this feature to change the Black level automatically according to the

brightness of an image.The Black level will become dark in a dark scene.

Picture

Sports

Standard

Movie

Memory

Bright and dynamic picture (factory-set)

Standard picture quality (factory-set)

Movie-like picture setting (factory-set)

Your personal preferences (set by you; see “Picture Setting”)

See page 22.

Preference

Picture Size

Film Mode

On/Off

A smoother motion may be obtained by setting the Film Mode to “On” when

you view a DVD from the DVD player connected with the component or

HDMI input (480i only).

PC Setting

Hor Position /

Ver Position

To adjust the horizontal / vertical position of the image on the PC Monitor

screen. Each video standard will require a different value for this setting.

Clock

Phase

Auto Adjust

On/Off

To minimize any vertical bars or stripes visible on the screen background.

This must be adjusted after the frequency has been set optimize picture quality.

To adjust the all PC settings automatically.

DNR (Digital Noise Reduction) can reduce the roughness of the picture.

A smoother motion may be obtained by setting the Motion 120Hz to On.

You can adjust the sound quality to your preference.

DNR

Motion 120Hz On/Off

Bass / Treble / Balance

Audio

MTS

Stereo / SAP /

The multi-channel TV sound (MTS) feature provides high-fidelity stereo

sound. MTS also can transmit a second audio program (SAP) containing a

second language or other audio information.

Mono

When the TV receives a stereo or SAP broadcast, the word “Stereo” or

“SAP” displays on-screen every time you press DISPLAY.

Audio Language

When two or more audio languages are included in a digital signal, you can

select an audio language. (This function is available only for digital broadcast.)

HDMI1 Audio HDMI

DVI

When you connect the HDMI device to the TV, select this setting.

When you connect the DVI device to the TV with analog audio cords, select this setting.

Use this feature to turn the TV speakers off when you connect an audio system.

Speakers

On/Off

Channel Add / Delete

DTV Signal

See page 18.

See page 19.

See page 18.

See page 19.

See page 20.

See page 21.

Auto Ch Memory

Ch Label

Lock

Setup

Closed Caption

Language

You can choose from three different languages (English, Français (French) and

Español (Spanish)) for the on-screen displays.

Select the language you prefer first, then proceed with the other menu options.

Video Label

On Timer

See page 19.

Off / 0h30m /

You can set On Timer to automatically turn on the TV. To cancel the On

1h00m / 1h30m

/ 2h00m /

Timer, set to “Off”.

3h00m⋅⋅⋅12h00m

On/Off

Auto Shut

Off*¹

If the Auto Shut Off feature is On, a station being viewed stops broadcasting and

the TV is not operated, the TV will automatically shut itself off after 15 minutes.

Auto Setup

Power On LED On/Off

See page 15.

When you turn on the TV, Power indicator on the front of the TV will light.You can

select On or Off.

Reset*²

The Reset function returns your Picture/Audio settings to the factory settings.

“Picture Setting”, “DBC”, “Picture Preference”, “Film Mode”, “PC Setting”,

“DNR”, “Motion 120Hz”, “Bass”, “Treble” and “Balance” can be reset by this

function.

NOTE:

If there is no input signal in the HDMI or PC mode, after 1 minute Auto Shut Off will be activated.

The device may not conform to the Energy Star standard after Reset is performed or the Backlight is adjusted.

Download from Www.Somanuals.com. All Manuals Search And Download.

The TV will begin memorizing all the channels

available in your area.

Memorizing channels

• It may take from 15 minutes to 30 minutes to

complete memorizing digital cable channels.

Depending on the reception condition, a bar

display may not advance for several minutes,

please be patient.

This TV is equipped with a channel memory

feature which allows channels to skip up or down

to the next channel set into memory, skipping

over unwanted channels. Before selecting

channels, they must be programmed into the

TV’s memory. To use this TV with an antenna, set

the Signal Type option to the Air mode. When

shipped from the factory, this menu option is in

the Cable mode.

NOTE:

•

Memorizing channels is best accomplished during

evening “PRIMETIME” hours, as more stations are

broadcasting digital signals. Memorizing channels can

only be accomplished while a station is broadcasting

a digital signal to set that channel into memory.

Air/Cable selection

• If you are unsure of the digital channels available

in your area, you may visit www.antennaweb.org to

receive a list based on your address or zip code.

Should you require further assistance you may call

our toll-free customer service line at 1-800-289-0980.

• New digital channels may be added to your area

periodically, it is recommended to perform the

“Automatic Search” procedure regularly.

Select “Channel”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Auto Ch Memory”, then

press ▶ or ENTER.

Press ▲ or ▼ to select “Signal Type”.

Press ◀ or ▶ to select “Air” or “Cable”.

Air - VHF/UHF channels

Adding Channel

Cable - CABLE TV channels

If you find a new digital channel unregistered, you can

add the new channel into the channel memory.

Auto Ch Memory

Signal Type

Cable

Start

Automatic Search

Tune in the new channel.

Select “Channel”, then press ▶ or ENTER.

: Select

: Adjust

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

CABLE CHART

Add/Delete

The chart below is typical of many cable system

channel allocations.

Adding Channel

Add/Delete

Clear All

: Select

ENTER:Set

Press ▲ or ▼ to select “Adding Channel”, then

press ▶ or ENTER. The new channel will be

added into the channel memory.

Add/Delete channel

NOTE:

You can select the channel that you want to skip.

• It may take a few seconds for a digital channel

picture to appear on screen after being selected.

Select “Channel”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Add/Delete”, then press

Automatic Search

▶ or ENTER.

Select “Channel”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Add/Delete”, then press

▶ or ENTER.

Press ▲ or ▼ to select “Auto Ch Memory”, then

press ▶ or ENTER.

Press ▲ or ▼ to select the channel that you want

to skip.

Add/Delete

Press ▲ or ▼ to select “Automatic Search”, then

press ▶ or ENTER.

Signal

Analog

Digital

Analog

Auto Ch Memory

Add

Signal Type

Cable

Stop

3-1

3-2

Delete

Add

Automatic Search

Delete

Analog Channel Found : 7

Digital Channel Found : 5

: Select

: Adjust

Programming Now

: Select

ENTER:Cancel

Press ◀ or ▶ to select “Add” or “Delete”,

whichever function you want to perform.

Repeat steps 4 - 5 for other channels you want to

add or delete.

Download from Www.Somanuals.com. All Manuals Search And Download.

Ch Label

Clear All

Channel Number

15-1

Ch Label

All channels are deleted from the channel memory.

Label Clear

Select “Channel”, then press ▶ or ENTER.

: Select

: Adjust

Press ▲ or ▼ to select “Add/Delete”, then press ▶

or ENTER.

Press ◀ or ▶ repeatedly until the character you

want appears in the first space.

Press ▲ or ▼ to select “Clear All”, then press ▶ or

ENTER.

Ch Label

Channel Number

15-1

Add/Delete

Ch Label

Adding Channel

Add/Delete

Clear All

Label Clear

: Select

: Adjust ENTER:Set

: Select

ENTER:Set

The characters rotation as follows:

, () @ / + =

Checking the digital

signal strength

SPACE

If the character which you desire appears, press

ENTER.

This TV will allow you to view the digital signal

meter for digital channels.

Repeat this step to enter the rest of the characters.

If you would like a blank space in the label name,

you must choose the empty space from the list of

characters.

Select “Channel”, then press ▶ or ENTER.

Press ▲ or ▼ to select “DTV Signal”.

Repeat steps 3-4 for other channel.You can

assign a label to each channel.

Press ▶ or ENTER to check the digital signal

When you finish inputting the label name, press

strength.

EXIT to return to the normal screen.

The digital signal strength screen will appear.

If necessary, adjust the direction of the antenna to

To clear a Ch Label

obtain the maximum signal strength.

After step 3 above, press ▲ or ▼ to select “Label

Clear”, then press ▶ or ENTER.

DTV Signal

NOTE:

• The channel labels will be reset after “Automatic

Search” on page 18.

100

Signal Level ⁰

NOTE:

Labeling video inputs

• Signal meter feature is not available for analog

channels.

The Video Label feature allows you to label each

input source for your TV.

• After 240 seconds, DTV Signal screen will return to

normal TV-operation automatically.

Select “Setup”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Video Label”, then press

Labeling channels

▶ or ENTER.

Channel label appear with the channel number

display each time you turn on the TV, select a

channel, or press DISPLAY.

Press ▲ or ▼ to select an input which you want to

label.

Press ◀ or ▶ to select the desired label for that

You can choose any four characters to identify a

channel.

input source.

Video Label

Video1

To create channel labels

Video2

Component

HDMI1

Select “Channel”, then press ▶ or ENTER.

HDMI2

HDMI3

Press ▲ or ▼ to select “Ch Label”, then press ▶

: Select

: Adjust

or ENTER.

–

: Uses the default label name

:Video cassette recorder

: DVD video

The Ch Label menu will appear.

VCR

DVD

DTV

SAT

CBL

Press ◀ or ▶ to select a channel you want to

: Digital TV set-top box

: Satellite box

label, then press ▼.

: Cable box

: HDMI device (only for HDMI inputs)

Download from Www.Somanuals.com. All Manuals Search And Download.

Genre:

Setting the V-Chip

ALL

: All

: Dialogue

: Language

: Sex

An age limitation can be set to restrict children from

viewing or hearing violent scenes or pictures that you

may choose to exclude. The restriction applies to “TV

Rating” and “Movie Rating” if this data is transmitted.

You may set this restriction separately. To use the

V-Chip function, you must register a password.

:Violence

: Fantasy Violence

Movie Rating

To register a password

PG-13

Select “Lock”, then press ▶ or ENTER.

NC-17

Select and enter your password (4 digits) using

: Select

ENTER:Set

Number buttons (0-9), then press ENTER.

: All ages

Lock

New Password

* * *

: Parental guidance

PG-13 : Parental guidance less than 13 years old

: Under 17 years old parental guidance

suggested

NC-17 : 17 years old and above

[0-9] : Select

ENTER:Set

: Adult only

“

” appears instead of the number.

Press ▲/▼/◀/▶ to select the desired rating, then

Enter the same password again to confirm, then

press ENTER.

The password is now registered.

Press EXIT to return to the normal screen.

V-Chip function is activated now.

NOTE:

• If you forget the password, contact Customer

Service at 1-800-289-0980 for assistance.

Your original remote control will be required.

• To avoid forgetting the password, write it down and

keep in a safe place.

To use the TV after the TV is protected.

When a program is received that is blocked by the

V-Chip, press MUTE, then enter your password.

The protection will be temporarily overridden. If the

TV is turned off or the channel is changed, the V-Chip

restriction will be reactivated.

To set the V-Chip

NOTE:

• The V-Chip function is activated only on programs

and input sources that include a rating signal.

Select “Lock”, then press ▶ or ENTER.

Use Number buttons (0-9) to enter your

To change the password

password, then press ENTER. The Lock menu

will appear.

Select “Lock”, then press ▶ or ENTER.

Press ◀ or ▶ to set “V-Chip” to “On”.

Use Number buttons (0-9) to enter your password,

then press ENTER. The Lock menu will appear.

Press ▲ or ▼ to select “V-Chip Set”, then press

▶ or ENTER.

Press ▲ or ▼ to select “Change Password”, then

The V-Chip Set menu appears.

press ▶ or ENTER.

The Change Password screen will appear.

Press ▲ or ▼ to select which rating will be used,

then press ▶ or ENTER. Each rating below will

Enter a new password using Number buttons

appear.

(0-9), then press ENTER.

TV Rating

Enter the same password again to confirm, then

TV Rating

ALL

press ENTER.

TV-Y

The password is now registered.

TV-Y7

TV-G

TV-PG

TV-14

TV-MA

Downloading the additional V-Chip rating system

As a supplement to the standard V-Chip rating

system, your television will be able to download an

additional rating system, if such a system becomes

available in the future.

: Select

ENTER:Set

You can set the rating using age level and genre.

Age:

TV-Y

: All children

To download the additional V-Chip rating system

(when available)

TV-Y7 : 7 years old and above

TV-G

: General audience

TV-PG : Parental guidance

Select “Lock”, then press ▶ or ENTER.

TV-14 : 14 years old and above

TV-MA : 17 years old and above

Use Number buttons (0-9) to enter your password,

then press ENTER.The Lock menu will appear.

Download from Www.Somanuals.com. All Manuals Search And Download.

Press ◀ or ▶ to set “V-Chip” to “On”.

Press ◀ or ▶ to set “CC Setting” to “On”.

On: Captions will be displayed on the screen.

Off: Captions will not be displayed on the screen.

Press ▲ or ▼ to select “V-Chip Set (DTV)”, then

press ▶ or ENTER.

Press ▲ or ▼ to select “Analog Caption” or “Digital

If the TV is not storing the additional rating

system, the TV will begin downloading it, which

may take some time to be completed.

Caption”.

When you select “Analog Caption”, you can

choose from C1, C2, C3, C4, T1, T2, T3 and T4.

Set your preferred content rating limits for the

additional rating system.

When you select “Digital Caption”, you can

choose from CS1, CS2, CS3, CS4, CS5 and CS6.

You also need “Update” procedure to update

rating information.

Press ◀ or ▶ to select the desired Closed

Caption mode for both Digital and Analog Caption.

NOTE:

• You can only download the additional V-Chip rating

system when your TV is receiving a digital signal.

• When you download the additional rating system, it

may take some time for the download to occur.

• The V-Chip rating information and system are not

determined or controlled by the TV.

Press ▲ or ▼ to select “CC Priority”, then press

◀ or ▶ to select “Digital CC” or “Analog CC”.

NOTE:

• Depending on the broadcast signal, some

Analog Captions will function with a Digital

broadcast signal. This step prevent that two

kind of captions are overlapping.

• The standard V-Chip rating system is available

whether your TV is receiving a digital signal or not,

and will block both analog and digital programs. To

set the restriction level using the standard V-Chip

rating system, select V-Chip Set in step 4.

• The downloadable V-Chip rating system is an

evolving technology, and availability, content, and

format may vary.

NOTE:

• If the program or video you selected is not closed-

captioned, no captions will display on-screen.

• If text is not available in your viewing area, a black

rectangle may appear on-screen. If this happens,

set the CC Setting to “Off”.

• You cannot select this feature if the TV is not

receiving a digital signal for the current station.

• When selecting Closed Captions, the captioning will

be delayed approx. 10 seconds.

•

If no caption signal is received, no captions will appear,

but the television will remain in the Caption mode.

To clear the all V-Chip settings

• Misspellings or unusual characters may

Select “Lock”, then press ▶ or ENTER.

occasionally appear during Closed Captioning.

This is normal with Closed Captioning, especially

with live programs. This is because during live

programs, captions are also entered live. These

transmissions do not allow time for editing.

• When Captions are being displayed, on-screen

displays, such as volume and mute may be seen

but may interfere with Closed Captions.

Use Number buttons (0-9) to enter your password,

then press ENTER. The Lock menu will appear.

Press ▲ or ▼ to select “V-Chip Clear”, then press

▶ or ENTER.

The V-Chip Clear screen will appear.

Use Number buttons (0-9) to enter your

• Some cable systems and copy protection systems

may interfere with the Closed Captioned signal.

• If using an indoor antenna or if TV reception is

very poor, the Closed Caption Decoder may not

appear or may appear with strange characters or

misspelled words. In this case, adjust the antenna

for better reception or use an outdoor antenna.

• Closed Caption menu also can be displayed by

pressing CCD on the remote control.

password, then press ENTER. All of your settings

return to the factory settings.

Closed Caption

WHAT IS CLOSED CAPTIONING?

This television has the capability to decode and

display Closed Captioned television programs.

Closed Captioning will display text on the screen

for hearing impaired viewers or it will translate and

display text in another language.

CC advanced

When you have selected Custom as the display

method, you can adjust the various setting listed

below as follows:

Captions: This Closed Caption mode will display

text on the screen in English or another language.

Generally, Closed Captions in English are transmitted

on C1 and Closed Captions in other languages are

transmitted on C2.

This feature is designed to customize Digital Captions

only.

Text: The Text Closed Caption mode will usually fill

1/2 of the screen with a programming schedule or

other information.

Select “Setup”, then press ▶ or ENTER.

Press ▲ or ▼ to select “Closed Caption”, then

press ▶ or ENTER.

Select “Setup”, then press ▶ or ENTER.

The Closed Caption menu will appear.

Press ▲ or ▼ to select “Closed Caption”, then

Press ◀ or ▶ to set “CC Setting” to “On”.

press ▶ or ENTER.

The Closed Caption menu will appear.

Press ▲ or ▼ to select “Digital CC Preset”, then

Download from Www.Somanuals.com. All Manuals Search And Download.

press ◀ or ▶ to select “Custom”.

Press ▲ or ▼ to select “CC Advanced”, then

press ▶ or ENTER.

The CC Advanced menu will appear.

Press ▲ or ▼ to select the desired item, then

press ◀ or ▶ to change the setting.

Cinema Wide1 (for 4:3 format programs)

To fill the screen, the right and left edges are

extended, however; the center of the picture remains

near its former ratio.

CC Advanced

Text Size

Auto

Text Type

Text Edge

Text Color

Text Opacity

Background Color

Background Opacity

The top and bottom edges of the picture may be hidden.

: Adjust

: Select

You can select from among the following items

and parameters.

Text Size:

Text Type:

Auto, Small, Standard, Large

Cinema Wide2 (for letter box programs)

The entire picture is uniformly enlarged—it is

stretched the same amount both wider and taller

(retains its original proportion).

Auto, Style1, Style2, Style3, Style4,

Style5, Style6, Style7

Text Edge: Auto, None, Raised, Depressed,

Uniform, Left Shadow, Right

Shadow

The top and bottom edges of the picture may be hidden.

Text Color: Auto, Black, White, Red, Green,

Blue, Yellow, Magenta, Cyan

Text Opacity: Auto, Solid, Transparent,

Translucent, Flashing

Background Auto, Black, White, Red, Green,

Color:

Blue, Yellow, Magenta, Cyan

Cinema Wide3 (for letter box programs with

subtitles)

Background Auto, Solid, Transparent,

Opacity: Translucent, Flashing

To fill the width of the screen, it is extended

horizontally. However; it is only slightly extended at the

top and the bottom.

NOTE:

• You cannot set both “Text Color” and “Background

Color” as a same color.

The top and bottom edges of the picture may be hidden.

• You cannot set both “Text Opacity” and “Background

Opacity” to “Transparent”.

A B C D E F G - - - - - - - - - - - - - - - -

A B C D E F G - - - - - - - - - - - - - - - - - - - - - - - - - -

Setting the picture size

Full (for 16:9 source programs)

Full will display the picture at the maximum size.

You can view 480i and 480p format programs in a

variety of picture sizes— Natural, Cinema Wide1,

Cinema Wide2, Cinema Wide3, Full and Native.

Selecting the picture size

Select “Picture”, then press ▶ or ENTER.

Native (for PC mode only)

Detects the resolution of the signal of the image and it

will be shown on the screen with same amount of pixels.

Press ▲ or ▼ to select “Picture Size”, then press

▶ or ENTER to display Picture Size menu. Press

▲ or ▼ or corresponding Number buttons (0-4) to

select the desired picture size, as described below.

Picture Size

0.Natural

1.Cinema Wide1

2.Cinema Wide2

3.Cinema Wide3

4.Full

NOTE:

• Some High Definition and/or Digital broadcasts may

not allow you to change the picture size.

• In HDMI or COMPONENT mode with a scanning

rate of 720p, 1080i or 1080p (HDMI only) only the

Cinema Wide2 and Full picture size feature are

available.

[0-4]:Select

NOTE:

• Selectable picture sizes may vary depending on the

input source or broadcast signal.

• In PC mode, only the Natural, Full and Native

picture size features are available. In PC mode

(WXGA, WXGA+, FHD), only the Full and Native

picture size features are available.

• Picture Size menu also can be displayed by

pressing PICTURE SIZE on the remote control.

• When the PC connected to the HDMI terminal and

1920x1080 resolution (FHD) is selected, the top

and bottom, right and left edges of the picture may

Natural

In some cases, this image will display the size of

standard 4:3 with a black side bar.

Download from Www.Somanuals.com. All Manuals Search And Download.

be hidden on all PICTURE SIZE.

Reception disturbances

Most types of television interference can be remedied by adjusting the height and position of the VHF/

UHF antenna. Outdoor antennas are recommended for best results. The most common types of television

interference are shown below. If one of these symptoms appear when the TV is connected to a Cable TV

system, the disturbance may be caused by the local Cable TV company broadcast.

IGNITION

Black spots or horizontal streaks may appear, the picture may flutter or

drift. Usually caused by interference from automobile ignition systems,

neon lamps or AC powered tools and appliances such as drills or hair

dryers.

GHOSTS

Ghosts are caused by the television signal following two paths. One is the

direct path and the other is reflected by tall buildings, hills or other large

objects. Changing the direction or position of the antenna may improve

the reception.

SNOW

If the TV is located far from the TV station, in a fringe reception area where

the signal is weak, small dots may appear in the picture.

If the signal is extremely weak, the installation of a larger external antenna

may be necessary.

RADIO FREQUENCY INTERFERENCE (RFI)

Caused by two-way radios, this type of interference produces moving

ripples or diagonal streaks in the picture. Some cases may cause a loss of

contrast in the picture. Changing the direction and position of the antenna

or installing an RFI filter may improve the picture.

PICTURE SIZE VARIATION

A slight picture size variation is normal when you adjust the CONTRAST or

BRIGHTNESS settings.

CARE AND MAINTENANCE

To prevent fire or shock hazard, disconnect the TV from the power source before cleaning.

The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture.

Use caution when cleaning or wiping the plastic parts.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Use the following checklist for troubleshooting if you have problems with your LCD TV. Consult your local dealer

or service outlet if problems persist. Be sure all connections are properly made when using with other units.

SYMPTOMS

POSSIBLE SOLUTIONS

SYMPTOMS

POSSIBLE SOLUTIONS

Digital

• Make sure the power cord is plugged in.

broadcasting

screen

• Try another AC outlet.

• Check digital signal strength.

TV does not

operate.

• Power is off, check fuse or circuit breaker.

• Unplug unit for an hour, then plug it back

in.

problem.

• Check all Cable TV connections.

• Set Signal Type menu option to the

Cable mode.

• Station or Cable TV experiencing

problems, tune to another station.

• Check sound adjustments (VOL +/– or

MUTE).

No CATV

reception.

• Station or Cable TV system problems,

Poor sound

or no sound.

try another station.

• Check for sources of possible

interference.

• Check antenna connections, adjust or

re-direct antenna.

Horizontal or

diagonal bars

on screen.

• Check for sources of possible

interference.

• Station or Cable TV experiencing

problems, tune to another station.

• Make sure channels are set into memory.

• Make sure Signal Type option is in the

No reception

above

Poor picture • Check antenna or Cable TV

appropriate mode.

or no picture.

connections, adjust antenna.

• Check for sources of possible

interference.

• If using antenna, check UHF antenna

connections.

channel 13.

• Batteries are weak, dead or inserted

• Check picture control adjustments.

incorrectly.

• Station or Cable TV experiencing

problems, tune to another station.

• Make sure channels are set into memory.

• Station is weak, adjust antenna to

receive desired station.

• Remote is out of range, move closer to

TV (within 15 feet).

No Remote

operation.

Poor

• Make sure Remote is aimed at sensor.

• Confirm there are no obstructions

between the Remote and the TV.

• Make sure the power cord is plugged in.

reception on

some

channels.

• Check for sources of possible

interference.

• Sleep Timer is set.

TV shuts off.

• Station or Cable TV experiencing

problems, tune to another station.

• Make sure channels are set into memory.

• Power interrupted.

• TV station experiencing problems or

program tuned is not closed captioned.

Try another channel.

Poor color or • Check picture control adjustments.

Closed

no color.

• Check antenna or Cable TV

connections, adjust antenna.

• Check for sources of possible

interference.

Caption is not

activated.

• Check Cable TV connection or VHF/UHF

antenna, reposition or rotate antenna.

• Set closed caption decoder in the menu.

TV is not

• Station or Cable TV experiencing

problems, tune to another station.

• Make sure channels are set into memory.

• Cable TV company is scrambling signal.

• Adjust antenna.

• Select proper language in the menu

options.

shown in your

language.

Picture

wobbles or

drifts.

BLOCK NOISE / PICTURE FREEZE

Block noise or picture freeze may appear on the screen caused by weak signals, interference from automobile

ignition systems, neon lamps or AC powered tools and appliances such as drills or hair dryers.

FOR CUSTOMER SERVICE, ADDITIONAL SET-UP AND OPERATING ASSISTANCE, OR TO ORDER ACCESSORIES PLEASE CALL:

1-800-289-0980

WHEN CALLING CUSTOMER SERVICE – PLEASE HAVE YOUR MODEL NUMBER READY

OR WRITE TO:

ORION SALES, INC.

3471 N. UNION DR.

OLNEY, ILLINOIS 62450

FOR INFORMATION ON OUR OTHER PRODUCTS, OR TO ORDER ACCESSORIES ONLINE, PLEASE VISIT OUR WEBSITE AT

www.orionsalesinc.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

SLED4280

SLED4680

GENERAL

Power supply:

Power consumption:

AC 120V 60Hz

Operation: 135 W

Standby: 0.3 W

15.8 kg (34.8 lbs)

Width: 1013 mm (39-7/8 inches)

Height: 679.5 mm (26-3/4 inches)

Depth: 255 mm (10-1/16 inches)

Operation: 152 W

18 kg (39.7 lbs)

Width: 1117 mm (43-15/16 inches)

Height: 748 mm (29-7/16 inches)

Depth: 255 mm (10-1/16 inches)

Weight:

Dimensions:

Operating temperature:

Operating humidity:

Type:

Display method:

Number of Pixels:

Broadcasting system:

5˚C - 40˚C

Less than 80% RH

106.73 cm (42" class/42.02" diagonal)

Transmission TFT color LCD panel

1920 (H) x 1080 (V)

116.81 cm (46" class/45.99" diagonal)

US system M

ATSC standard (8VSB), QAM

Receiving channels:

VHF

2-13

UHF

14-69

CATV 14-36 (A)-(W)

37-59 (AA)-(WW)

60-85 (AAA)-(ZZZ)

86-94 (86)-(94)

95-99 (A-5)-(A-1)

100-135 (100)-(135)

01 (4A)

Tuner type:

Inputs:

Frequency synthesized

Video: (RCA) 1 V (p-p), 75 ohms

Audio:

(RCA) –8 dBm/50k ohms

Component video:

(Y) 1 V (p-p), 75 ohms

(Pb)/(Pr) 0.7 V (p-p), 75 ohms

HDMI: HDMI compliant (type A connector)

HDCP compliant

E-EDID compliant

Suggested scan rates: 480p, 480i, 720p,1080i,1080p

HDMI Audio: 2-channel PCM

32/44.1/48 kHz sampling frequency

16/20/24 bits per sample

PC Monitor: Mini-Dsub 15pin x 1

Antenna:

VHF/UHF In 75 ohms coaxial

Outputs:

Digital audio out:

0.5 V(p-p), 75 ohms terminated

Audio: 0-600 mV rms / 1k ohm

Speaker:

Woofer:

Audio output power:

ACCESSORIES

20.3 mm x 149.9 mm (13/16 inches x 5-7/8 inches), 8 ohms x 2

109.2 mm x 137.2 mm (4-5/16 inches x 5-3/8 inches), 4 ohms x 1

10W + 10W + 15W

Remote control

Batteries AAA x 2

Stand

Screws x 4

Designs and specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

limited

WARRANTY

42/46” CLASS WIDE LED TV

ORION warrants this product to be free from manufacturing defects in material and workmanship under

normal use and conditions for a period of 1 year from date of original purchase in the United States.

Should service be necessary under this warranty for any reason due to a manufacturing defect or

malfunction during the first 12 months from date of original purchase, ORION will provide in-home repair

service by an ORION authorized Independent Service Center at no charge. Also, if an original part fails due to

manufacturing defect in material and workmanship within one year from date of original purchase we will replace

the defective part, provided the defect or malfunction is verified along with dated proof of purchase.

There are ORION authorized Independent Service Centers located throughout the country. For the one

nearest you, DIAL TOLL FREE: 1-800-289-0980 or visit our website at www.orionsalesinc.com. ORION will not

be liable for damages incurred in shipment of the unit. If there are no ORION authorized Independent Service

Centers in your area please call - 1-888-296-7466 for assistance.

Note: This warranty is void if the product is:

(a) Damaged through negligence, misuse, abuse, or accident.

(b) Used in a commercial application or rentals.

warranty repairs to the class of product or by the ORION Factory Service Center.

(d) Damaged because it is improperly connected to the equipment of other manufacturers.

This warranty does not cover:

(a) Damage to equipment not properly connected to the product.

(b) Costs incurred in the shipping of the product to an ORION authorized Independent Service Center or

ORION Factory Service Center.

operating instructions provided with the product.

(d) Ordinary adjustments to the product which can be performed by customer as outlined in the owner’s

manual.

(e) Signal reception problems caused by external antenna or cable systems.

THIS WARRANTY IS NON TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER

AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. ANY APPLICABLE IMPLIED

WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED IN DURATION TO A

PERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH THE DATE OF ORIGINAL

PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED SHALL APPLY TO THIS

PRODUCT THEREAFTER. ORION MAKES NO WARRANTY AS TO THE FITNESS OF THE PRODUCT FOR

ANY PARTICULAR PURPOSE AND USE.

UNDER NO CIRCUMSTANCES SHALL ORION BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE

USE OF THIS PRODUCT.

THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA. THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, HOWEVER, YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE

TO STATE. SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES OR EXCLUSION OF

CONSEQUENTIAL DAMAGE, THEREFORE THESE RESTRICTIONS MAY NOT APPLY TO YOU.

ORION SALES, INC.

3471 N. UNION DR.

OLNEY, ILLINOIS 62450

Download from Www.Somanuals.com. All Manuals Search And Download.

Memo

..................................................................................................

Download from Www.Somanuals.com. All Manuals Search And Download.

Quantum Mobility Aid 6000Z User Guide
RCA Flat Panel Television HDLP61W151 User Guide
RCA MP3 Player M4202 User Guide
Remington Power Tools Car Speaker DPS 1 111409 01 User Guide
Rockford Fosgate Car Amplifier T10001 BD User Guide
Ryobi Chainsaw P514 User Guide
Ryobi Trimmer 767r User Guide
Samsung Microwave Oven SMH5165 User Guide
Sanyo Vacuum Cleaner SC B550 User Guide
Schneider Electric Marine Radio VW3 A3 303 User Guide