Samsung VCR SV 665B User Guide

VIDEO  
CASSETTE RECORDER  
SV-665B SV-662B  
SV-661B SV-262B  
SV-265B SV-661I  
SV-261B SV-261I  
Instruction Manual  
PAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sa fe ty Pre ca u tio n s  
Ab o u t th is m a n u a l  
GB  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
Thank you for purchasing a Samsung Video Cassette Recorder (VCR).  
Your Owners Instructions contain much valuable information on setting up and  
using your VCR. Please take the time to read them as they will help you take full  
advantage of your VCR’s features.  
DAN GER  
This symbol is intended to alert you to the  
presence of dangerous voltage within the  
product.  
CAUTION. TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE REAR COVER. NO  
USER SERVICEABLE PARTS INSIDE. REFER TO  
QUALIFIED SERVICE PERSONNEL.  
The instructions in this manual are for models, SV-665B, SV-661B, SV-265B,  
SV-261B, SV-662B, SV-262B, SV-661I and SV-261I. Before you start reading this  
manual please check your model number. It is displayed on the rear of the VCR.  
IMPORTANT NOTE  
The mains lead on this equipment is supplied with a  
moulded plug incorporating a fuse. The value of the fuse is  
indicated on the pin face of the plug. If it requires  
replacing, a fuse approved to BS1362 of the same rating  
must be used.  
- (SV-665B): Exceptions only for a certain model, for example SV-665B.  
CAUTIO N  
This symbol is intended to alert you to the  
presence of important instructions  
accompanying the product.  
- Gray shaded areas marked with a star indicate instructions that are  
only relevant to one model.  
Never use the plug with the fuse cover omitted if the cover  
is detachable. If a replacement fuse cover is required, it  
must be of the same colour as the pin face of the plug.  
Replacement covers are available from your dealer.  
Features Chart  
If the fitted plug is not suitable for the power points in your  
house or the cable is not long enough to reach a power  
point, you should obtain a suitable safety approved  
extension lead or consult your dealer for assistance.  
SV-261B  
SV-262B  
SV-661B  
SV-662B  
Model  
SV-665B SV-265B SV-661I SV-261I  
Feature  
However, if there is no alternative to cutting off the plug,  
remove the fuse and then safely dispose of the plug. Do  
not connect the plug to a mains socket, as there is a risk of  
shock hazard from the bared flexible cord.  
VIDEOPLUS+ Recording  
AV2 IN socket  
Format 16:9  
IMPORTANT  
The wires in the mains lead are coloured in accordance  
with the following code: -  
Child Door Lock  
IPC (Intelligent Picture Control)  
Timer Programming  
BLUE = NEUTRAL  
BROWN = LIVE  
Auto Clock Setting  
As these colours may not correspond with the coloured  
markings identifying the terminals in your plug, proceed as  
follows: -  
Changing recording speed (SP/LP)  
Hi-Fi & NICAM  
The wire coloured BLUE must be connected to the  
terminal marked with the letter N or coloured BLUE or  
BLACK. The wire coloured BROWN must be connected to  
the terminal marked with the letter L or coloured BROWN  
or RED.  
Connecting an RCA Audio/Video cable  
Using the TV Buttons On the  
Remote Control  
WARNING: DO NOT CONNECT EITHER WIRE TO THE  
EARTH TERMINAL WHICH IS MARKED WITH THE  
LETTER E OR BY THE EARTH SYMBOL  
, OR  
COLOURED GREEN OR GREEN AND YELLOW.  
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n te n ts  
Co n te n ts (co n t.)  
GB  
GB  
FOREWORD  
Safety Instructions.........................................................................................  
SEARCHING FOR A SEQUENCE  
6
Playing a Cassette in Slow Motion (SV-665B/SV-661B/SV-662B/SV-661I Only)... 34  
Playing a Sequence Frame by Frame........................................................... 35  
Picture Search, Fast Forward/Rewind........................................................... 35  
Searching for a Specific Sequence ............................................................... 36  
Auto Repeat Play........................................................................................... 37  
Interval Repeat Play ...................................................................................... 37  
VCR OVERVIEWS  
Front View of the VCR...................................................................................  
Rear View of the VCR ...................................................................................  
Infrared Remote Control................................................................................  
Display Indicators .......................................................................................... 10  
Accessories ................................................................................................... 10  
7
8
9
EASY OPERATION  
VIDEOPLUS+ EXTEND (SV-665B/SV-265B Only)....................................... 38  
Using the Tape Counter ................................................................................ 38  
CONNECTING YOUR VIDEO CASSETTE RECORDER  
Deciding How to Connect Your VCR............................................................. 11  
Connecting Your VCR to the TV using the Coaxial Cable and SCART cable..... 12  
Connecting Your VCR to the Satellite receiver or Other Equipment ............. 13  
Connecting the Audio Output Cable (SV-665B/SV-661B/SV-662B/SV-661I Only)....... 14  
Plug & Auto Set Up........................................................................................ 14  
Tuning Your Television for the VCR.............................................................. 15  
ADVANCED RECORDING FEATURES  
Connecting an RCA Audio/Video Input cable (SV-665B/SV-661B/  
SV-662B/SV-661I Only)................................................................................. 39  
Using the Assemble Edit Function................................................................. 40  
Recording from Another VCR or Camcorder................................................. 40  
SETTING UP YOUR VIDEO CASSETTE RECORDER  
OTHER FUNCTIONS AND USEFUL RECOMMENDATIONS  
Inserting Batteries in the Remote Control...................................................... 16  
Setting the Date and Time............................................................................. 16  
Displaying/Hiding On-Screen Information ..................................................... 17  
Setting the VCR Output Channel................................................................... 17  
Presetting the Stations Automatically............................................................ 18  
Presetting the Stations Manually................................................................... 19  
Clearing a Preset Station............................................................................... 20  
Changing the Preset Station Table................................................................ 21  
Using the TV Buttons on the Remote Control (SV-665B Only) ..................... 41  
Auto Power Off .............................................................................................. 42  
Child Door Lock System (SV-665B/SV-661B/SV-662B/SV-661I/  
SV-265B/SV-261B/SV-262B/SV-261I Only).................................................. 42  
ECO Mode-Reducing Standby power consumption...................................... 42  
Technical Specifications................................................................................ 43  
SOLVING PROBLEMS  
Problems and Solutions................................................................................. 44  
Service Centers List ...................................................................................... 45  
RECORDING TELEVISION BROADCASTS  
Selecting the Cassette Type.......................................................................... 22  
Selecting the Recording Speed..................................................................... 22  
NICAM (SV-665B/SV-661B/SV-662B/SV-661I Only).................................... 23  
Protecting a Recorded Cassette.................................................................... 24  
Recording a Programme Immediately........................................................... 24  
Recording a Programme with Automatic Stop............................................... 25  
Using the VIDEOPLUS+ Feature (SV-665B/SV-265B Only)......................... 26  
Modifying VIDEOPLUS+ Programming (SV-665B/SV-265B Only).................... 27  
Using the Timer Programming Feature ......................................................... 28  
Checking a Preset Recording........................................................................ 29  
Cancelling a Preset Recording...................................................................... 29  
PLAYING BACK  
Symbols  
Playing a Cassette......................................................................................... 30  
Adjusting Picture Alignment Automatically (SV-661B/SV-662B/SV-661I/  
SV-265B/SV-261B/SV-262B/SV-261I Only)......................................................... 30  
Adjusting Picture Alignment Manually ........................................................... 30  
Intelligent Picture Control .............................................................................. 31  
Intelligent Picture Control (SV-661B/SV-662B/SV-661I/SV-265B/SV-261B/  
SV-262B/SV-261I Only) .................................................................................... 31  
Format 16:9 (Wide Screen) (SV-665B/SV-661B/SV-662B//SV-661I Only) ... 32  
Selecting the Colour Mode ............................................................................ 32  
Selecting the Audio Output Mode (SV-665B/SV-661B/SV-662B/SV-661I Only) ....... 33  
Selecting the Audio Mute Mode (SV-265B/SV-261B/SV-262B/ ....................  
SV-261I Only)................................................................................................ 33  
1
1
Press/push  
Hold down  
Important  
Note  
Option  
= Step number  
1
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fro n t Vie w o f th e VCR  
Sa fe ty In stru ctio n s  
GB  
GB  
(SV-665B/SV-661B/SV-661I)  
RECORD  
BUTTON  
PLAY  
BUTTON  
STANDBY/ON  
The following illustrations represent precautions.  
VIDEO CASSETTE  
COMPARTMENT  
BUTTON  
PAUSE/STILL  
BUTTON  
F.F  
EJECT  
BUTTON  
BUTTON  
The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.  
DO NOT OPEN THE VCR. Refer to service personnel.  
EJECT  
STANDBY/ON  
REW  
F.F  
PROG  
REC  
STOP  
II P/S  
VIDEO  
L
AUDIO  
R
LINE IN  
10%  
75%  
40°C  
H
H
5°C  
AUX AUDIO L, R  
INPUT SOCKETS  
REW  
BUTTON  
AUX VIDEO INPUT  
SOCKET  
PROGRAMME SELECTION  
BUTTONS  
STOP  
BUTTON  
(SV-265B/SV-261B/SV-261I)  
VIDEO CASSETTE  
COMPARTMENT  
STOP  
BUTTON  
REW  
BUTTON  
STANDBY/ON  
F.F  
BUTTON  
BUTTON  
EJECT  
Do NOT expose the VCR to  
extreme temperature condi-  
tions (below 5°C and above  
40°C) or to extreme humidity  
conditions (less than 10% and  
more than 75%).  
Do NOT expose the VCR to  
direct sunlight.  
Do NOT expose the VCR to  
any liquids.  
BUTTON  
STANDBY/ON  
EJECT  
REW  
F.F  
II P/S  
REC  
STOP  
PROG  
PROGRAMME SELECTION  
BUTTONS  
RECORD  
BUTTON  
PLAY  
BUTTON  
PAUSE/STILL  
BUTTON  
Do NOT place any objects on  
the VCR or remote control.  
During a storm and/or light-  
ning, unplug the VCR from the  
mains socket and aerial.  
If the remote control is not  
used for a long period of time,  
remove the batteries and store  
it in a cool, dry place.  
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL  
ENVIRONMENTS  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Re a r Vie w o f th e VCR  
In fra re d Re m o te Co n tro l  
GB  
GB  
(SV-665B)  
VCR STANDBY/ON  
TV STANDBY/ON  
TV STANDBY/ON BUTTON  
VCR STANDBY/ON BUTTON  
SLOW BUTTON  
SLOW  
AV2 (SATELLITE) IN SCART (EURO-21) SOCKET  
(SV-665B/SV-661B/SV-662B/SV-661I ONLY)  
SHUTTLE  
AERIAL IN  
CONNECTOR  
SHUTTLE BUTTON  
V-LOCK  
F.ADV  
V-LOCK BUTTON  
CLR/RST  
-/--  
INDEX  
INDEX BUTTON  
CLEAR AND RESET BUTTON  
FRAME ADVANCE BUTTON  
SELECT  
TV  
VCR  
INPUT  
TV BUTTON  
VCR BUTTON  
TUNER, AV1, AV2, AUX SELECTION /  
REPEAT SELECTION BUTTON  
REPEAT  
DISP./  
AUDIO  
VOLUME BUTTONS  
PROGRAMME SELECTION /  
TRACKING BUTTONS  
AV2 (SATELLITE) IN  
VOL  
PROG/TRK  
AUDIO MODE SELECTION BUTTON  
STOP BUTTON  
DISPLAY BUTTON  
OUT/SORTIE  
PLAY/PAUSE/STILL BUTTON  
R/D  
TV  
REWIND/REVERSE PICTURE  
SEARCH BUTTON  
AUDIO  
L/G  
FAST-FORWARD/FORWARD  
SEARCH BUTTON  
REC  
MENU  
AV1 (EURO AV)  
RECORD BUTTON  
MENU BUTTON  
MENU SELECTION UP BUTTON  
MENU SELECTION BUTTON  
OK  
MENU SELECTION BUTTON  
MENU SELECTION DOWN BUTTON  
OK BUTTON  
RCA AUDIO L, R OUTPUT SOCKETS  
(SV-665B/SV-661B/SV-662B/SV-661I ONLY)  
AV1 (EURO AV) IN/OUT  
SCART (EURO-21) SOCKET  
OUT TO TV  
CONNECTOR  
SPEED  
DUB  
TV/VCR  
TIMER  
RECORDING SPEED SELECTION BUTTON  
TIMER/PROGRAMME VIDEOPLUS BUTTON  
(SV-661B/SV-265B/SV-261B  
SV-662B/SV-262B/SV-661I  
STANDBY/ON  
EJECT  
SV-261I)  
EJECT BUTTON  
STANDBY/ON BUTTON  
SLOW  
SLOW BUTTON  
(SV-661B/SV-662B/SV-661I ONLY)  
SHUTTLE  
SHUTTLE BUTTON  
V-LOCK  
F.ADV  
V-LOCK BUTTON  
CLR/RST  
INDEX  
CLEAR AND RESET BUTTON  
INDEX BUTTON  
FRAME ADVANCE BUTTON  
A.TRK  
IPC  
INPUT  
TUNER, AV1, AV2, AUX (SV-661B/SV-662B/  
AUTO TRACKING BUTTON  
IPC BUTTON  
REPEAT  
SV-651I ONLY) SELECTION / REPEAT  
SELECTION BUTTON  
TRACKING BUTTONS  
AUDIO  
DISPLAY  
TRK  
PROG  
AUDIO MODE SELECTION BUTTON  
(SV-661B/SV-662B//SV-661I ONLY)  
AUDIO MUTE BUTTON  
(SV-265B/SV-261B/SV-262B/SV-261I ONLY)  
DISPLAY BUTTON  
PROGRAMME SELECTION BUTTON  
PLAY/PAUSE/STILL BUTTON  
FAST-FORWARD/FORWARD  
SEARCH BUTTON  
STOP BUTTON  
REC  
MENU  
REWIND/REVERSE PICTURE  
SEARCH BUTTON  
MENU BUTTON  
MENU SELECTION UP BUTTON  
RECORD BUTTON  
OK  
MENU SELECTION BUTTON  
MENU SELECTION BUTTON  
OK BUTTON  
MENU SELECTION DOWN BUTTON  
SPEED  
DUB  
TV/VCR  
TIMER  
TIMER/PROGRAMME VIDEOPLUS (SV-265B ONLY)  
RECORDING SPEED SELECTION BUTTON  
BUTTON  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Disp la y In d ica to rs  
De cid in g Ho w to Co n n e ct Yo u r VCR  
GB  
GB  
You must take into account various factors when connecting audio or video systems:  
Types of connectors available on your systems  
1
2
3
4
Systems connected permanently to the VCR (satellite receiver for example) or temporarily  
(camcorder for example)  
Your VCR is equipped with the following connectors.  
STEREO  
Connector  
Location  
Type  
Direction  
Recommended Use  
AV1 (EURO AV) Rear  
SCART  
In/Out  
Television  
Satellite receiver  
Other VCR  
5
6
AV1 (EURO AV)  
OUT TO TV  
Rear  
75  
Out  
In  
Television  
TV  
1 Cassette loaded indicator  
2 PLAY indicator  
3 Multi-function display  
4 Timer indicator  
coaxial  
IN FROM ANT. Rear  
75 Ω  
Aerial  
5 STEREO indicator  
(SV-665B/SV-661B/SV-662B/SV-661I ONLY)  
6 Rec indicator  
coaxial  
Cable television network  
Satellite receiver  
AV2  
(SATELLITE)  
Rear  
SCART  
In  
Satellite receiver  
Other VCR  
AV2 (SATELLITE) IN  
(SV-665B/SV-661B/SV-662B/SV-661I Only)  
AUX  
Front  
Audio/Video RCA  
In  
Audio Hi-Fi system  
Camcorder  
(SV-665B/SV-661B/SV-662B/SV-661I Only)  
Acce sso rie s  
Audio output  
Rear  
Audio RCA  
Out  
Audio Hi-Fi system  
OUT/SORTIE  
R/D  
AUDIO  
L/G  
(SV-665B/SV-661B/SV-662B/SV-661I Only)  
You have just purchased a SAMSUNG Video Cassette Recorder (VCR).  
Together with your VCR, you will find the following accessories in the box.  
Whenever you connect an audio or video system to your VCR, ensure that all elements are  
switched off.  
REMOTE CONTROL  
OWNERS  
INSTRUCTIONS  
COAXIAL CABLE  
Refer to the documentation supplied with your equipment for detailed connection instructions  
and associated safety precautions.  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Co n n e ctin g Yo u r VCR to th e TV u sin g th e Co a x ia l  
Ca b le a n d SCART ca b le  
Co n n e ctin g Yo u r VCR to th e Sa te llite re ce ive r o r O th e r  
Eq u ip m e n t  
GB  
GB  
To receive television programmes a signal must be received from  
one of the following sources:  
You can connect your VCR to a Satellite receiver or other VCR using the SCART cable if the appropriate  
outputs are available on the equipment chosen. The following illustrations give a few examples of the  
connection possibilities.  
An outdoor aerial  
An indoor aerial  
A cable television network  
A satellite receiver  
1. AV2(SATELLITE): By means of 21-pin Scart Cable (SV-665B/SV-661B/SV-662B/SV-661I Only)  
T
Make sure that both the television and the VCR are  
switched off before connecting the cables.  
Plug the SCART Cable with satellite receiver or other equipment into the AV2(SATELLITE) socket on the rear of  
the VCR.  
2
AV1 (EURO A
After making this connection, select the source by pressing the INPUT button for the AV2 input sources.  
1
2
Remove the aerial or network input cable from the television.  
2. By means of RF Coaxial Cable  
Connect this cable to the 75coaxial socket marked  
rear of your VCR.  
on the  
After making this connection, you must preset the station received through the satellite tuner.  
RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the VCR,  
e.g. re-adjust to channel 65.  
TV  
3
4
Plug the coaxial cable supplied into the  
socket on your VCR.  
VE
AV1 (EURO AV)  
3
TV  
TV  
Plug the other end of the coaxial cable into the connector  
previously used for the aerial on the television.  
Aerial  
5
6
Connect one end of the scart cable to the AV1 (EURO AV) socket  
on the rear of the VCR. You must connect your VCR to the  
television via the scart cable.  
4
Satellite Receiver or other Equipment  
Aerial Connector  
Plug the other end into the appropriate connector on the  
television.  
2
SCART Cable  
TV  
TV  
1
AV1 (EURO AV)  
5
AV2 (SATELLITE) IN  
TV  
AV1 (EURO AV)  
SCART Cable  
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(SV-6 6 5 B/ SV-6 6 1 B/  
Tu n in g Yo u r Te le visio n fo r th e VCR  
Connecting the Audio Output Ca ble  
SV-6 6 2 B/ SV-6 6 1 I O n ly )  
GB  
GB  
You must tune your television for the VCR only if you are not using  
a Scart cable  
You can connect your VCR to a Hi-Fi system.  
(SV-661B/SV-662B/  
Example: You wish to take advantage of the quality of your Hi-Fi  
stereo system when watching a programme or recording  
via your VCR.  
SV-661I/ SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
To view pictures from your VCR when a Scart cable is  
used, the television must be set to the audio/video mode  
(AV).  
(SV-665B)  
AV2 (SATELLITE) IN  
OUT/SORTIE  
Regardless of the type of connection chosen, you  
must always connect the coaxial cable supplied.  
Otherwise, no picture will be visible on the screen  
when the VCR is switched off.  
R/D  
TV  
AUDIO  
L/G  
AV1 (EURO AV)  
STANDBY/ON  
VCR STANDBY/ON  
1
2
Switch on the television.  
1
SLO  
Make sure that both the television and the VCR are  
Switch on the VCR by pressing STANDBY/ON on the front of the  
VCR or VCR STANDBY/ON (STANDBY/ON) on the remote  
control.  
2
S
2
switched off before connecting the cables.  
SHUT  
1
2
Connect the coaxial cable or SCART as indicated on page 12.  
SH  
AV2 (SATELLITE) IN  
3
4
Select a programme position on the television to be reserved for  
use with your VCR.  
2
Plug the audio output cable into the audio connectors on the rear  
of your VCR.  
OUT/SORI
R/D  
Insert the video cassette in the VCR. Check that the VCR starts  
Respect the colour coding of the left and right channels.  
AUDIO  
L/G  
AV1 (EURO AV)  
reading the cassette; if not, press  
.
button  
II  
3
Plug the other end of the audio cable into the appropriate input  
connectors on your Hi-Fi stereo system.  
2
5
6
7
Start a scan on your television or set the television to UHF  
channel 60.  
REC  
U  
4
Fine tune the television until the pictures and sound are obtained  
clearly.  
OK  
Plu g & Au to Se t Up  
If you cannot find the pictures and sound, or there is interference  
from nearby channels, it may be necessary to change the setting  
of the VCR output channel (see Setting the VCR Output Channel  
on page 17 and Problems and Solutions on page 49).  
Your VCR will automatically set itself up when it is plugged into the  
mains for the first time. TV stations will be stored in memory. The  
process takes a few minutes. Your VCR will then be ready for use.  
TV  
8
When the picture and sound are perfectly clear, store this channel  
at the desired programme position on the television.  
1
2
3
Connect the coaxial cable as indicated on page 12.  
(Connecting Your VCR to the TV Using the Coaxial Cable)  
Result:  
That programme is now reserved for use with your VCR.  
Plug the VCR into the mains.  
TV  
1 (EURO AV)  
Result:  
A message appears.  
Press OK button to start the auto scanning  
The number of stations automatically stored by the VCR  
depends on the number of stations that it has found.  
The process will finish after a few minutes.  
4
The current time and date are displayed automatically.  
Check the date and time.  
if it is :  
2
Correct, Press MENU button twice to exit the menu.  
incorrect, see page 16.  
Auto preset can be performed by pressing (STOP) on  
the VCR continuously for 5 seconds or more with no  
tape inserted.  
Function for “Plug & Auto Set Up” is fixed already.  
So if you want to change this fixed one, you can change  
it by Presetting the Stations Automatically in OSD  
“ Auto Set Up” menu. (see page 18)  
14  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In se rtin g Ba tte rie s in th e Re m o te Co n tro l  
Disp la y in g / Hid in g O n -Scre e n In fo rm a tio n  
GB  
GB  
You must insert or replace the batteries in the remote control when  
you:  
Your VCR displays most information both on the VCR and the  
television.  
Purchase the video cassette recorder  
(SV-665B/SV-661B/SV-662B/SV-661I)  
You can choose to display or hide this information on the television  
screen (except for the Index, Programming MENU and  
1
Find that the remote control is no longer working  
VIDEOPLUS+ functions (SV-665B/SV-265B only), which cannot  
correctly  
PTIONS  
be hidden).  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:AUTO  
:ON  
:OFF  
:ON  
1
2
Push the tab in the direction of the arrow to release the battery  
compartment cover on the rear of the remote control.  
1
2
3
4
5
Press MENU on the remote control.  
Result:  
The programming menu is displayed.  
Insert two AA, R6 or equivalent batteries, taking care to respect  
the polarities:  
œ❷  
END:MENU  
Press the corresponding  
œ,  
or  
,
buttons to select the  
+ on the battery with + on the remote control  
– on the battery with – on the remote control  
USER SEToption.  
(SV-265B/SV-261B/SV-262B/SV-261I)  
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
3
Replace the cover by aligning it with the base of the remote  
control and pushing it back into place.  
Press the corresponding  
selected.  
œ
or  
buttons, until the OSDoption is  
PTIONS  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:OFF  
:ON  
Do not mix different battery types (manganese and  
alkaline for example).  
To...  
Press  
or , until...  
Display on-screen information  
Hide on-screen information  
ONis displayed.  
Se ttin g th e Da te a n d Tim e  
œ❷  
END:MENU  
OFFis displayed.  
6
On completion, press MENU twice to exit the menu.  
Your VCR contains a 24-hour clock and calendar used to:  
Automatically stop programme recording  
Preset your VCR to record a programme automatically  
REC  
MENU  
2
You must set the date and time when:  
You purchase the video cassette recorder  
Se ttin g th e VCR O u tp u t Ch a n n e l  
OK  
2
2
The time and date are set automatically from the  
broadcast signal. If the signal is weak or ghosting  
occurs, the time and date may not be set automati-  
cally. In this case, they should be set manually.  
3
Your VCR output channel may need to be changed if the pictures  
suffer from interference or if your TV cannot find the pictures.  
Also, you can change the VCR output channel to adjust the  
frequency in which information is displayed on the screen.  
Do not forget to reset the time when you change  
INSTALL  
OPTIONS
PROG  
clocks from winter to summer time and vice versa.  
1
2
3
4
5
6
Press MENU on the remote control.  
PROG  
OPTIONS INSTALL  
CLOCK  
BONUS  
1
2
3
Press MENU on the remote control.  
Result:  
The programming menu is displayed.  
INSTALLATION  
Result:  
The programming menu is displayed.  
CLOCK  
BONUS  
Press the corresponding  
œ
,
or  
,
buttons to select the  
CLOCK SET  
Press the corresponding  
CLOCK SEToption.  
œ
,
or  
,
buttons to select the  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
INSTALLATIONoption.  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
Press the OK button to select this option.  
Result: The INSTALLATIONmenu is displayed.  
Press the OK button to select this option.  
Result: The CLOCK SETmenu is displayed.  
INSTALL  
4
5
Press  
Result:  
or to select the hour, minutes, day, month and year.  
The option selected flashes.  
AUTO SET UP  
MANUAL SET UP  
VCR OUTPUT CH :CH60  
Press the corresponding  
CHoption is selected.  
œ
or  
buttons, until the VCR OUTPUT  
CLOCK  
Press the  
Result:  
œ
or buttons to increase or decrease the value.  
12:00  
1/JAN/2003  
Select the required output channel (CH21~CH69) by pressing the  
or buttons.  
The day of the week is displayed automatically.  
or buttons down to scroll more  
quickly through the values.  
On completion, press MENU twice to exit the menu.  
WED  
You can hold the  
œ
AUTO CLOCK : ON  
œ❷  
END:MENU  
On completion, press MENU twice to exit the menu.  
Then tune your television again (see page 15).  
➛❿ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀœ❷  
END:MENU  
6
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pre se ttin g th e Sta tio n s Ma n u a lly  
Pre se ttin g th e Sta tio n s Au to m a tica lly  
GB  
GB  
You do not need to preset the stations if you have already  
set them automatically (see Plug & Auto Set Up on  
page 14).  
You do not need to preset the stations manually if you  
have already set them automatically.  
1
2
3
4
5
Press the MENU button on the remote control.  
Result: The programming menu is displayed.  
Your VCR contains a built-in tuner used to receive television  
broadcasts.  
INSTALL  
OPTIONS
PROG  
INSTALL  
OPTIONS
PROG  
You must preset the stations received through the tuner. This can  
be done:  
CLOCK  
BONUS  
Press the corresponding  
œ,  
or  
,
buttons to select the  
CLOCK  
BONUS  
INSTALLATIONoption.  
INSTALLATION  
INSTALLATION  
Plug & Auto Set up (see page 14)  
Automatically  
Manually (see page 19)  
Press the OK button to select this option.  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
Result:  
The INSTALLATIONmenu is displayed.  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
You can store up to 80 stations.  
Press the corresponding  
UPoption is selected.  
œ
or  
buttons, until the MANUAL SET  
INSTALL  
Press the  
Result:  
button to select a MANUAL SET UPoption.  
The TV STATION TABLEmenu is displayed.  
AUTO SET UP  
MANUAL SET UP  
VCR OUTPUT CH :CH60  
INSTALL  
1
2
3
4
Press the MENU button on the remote control.  
Result: The programming menu is displayed.  
AUTO SET UP  
MANUAL SET UP  
VCR OUTPUT CH :CH60  
6
7
Press the  
required.  
œ
or  
buttons to select a programme number as  
Press the corresponding  
œ,  
or  
,
buttons to select the  
INSTALLATIONoption.  
Press the ❿ꢀbutton to preset the station.  
œ❷  
END:MENU  
Result:  
The MANUAL TUNINGmenu is displayed.  
Press the OK button to select this option.  
œ❷  
END:MENU  
Result:  
The INSTALLATION menu is displayed.  
8
9
Press the  
Result:  
or buttons to start scanning.  
The frequency band is scanned and the first station  
found is displayed.  
Press the corresponding  
UPoption is selected. And then press the  
option.  
œ
or  
buttons, until the AUTO SET  
button to select this  
TV STATION TABLE  
**  
**  
Press the  
œ
or  
buttons until the NAMEis selected.  
PR  
CH  
27  
--  
--  
--  
--  
NAME  
CAEB  
----  
----  
----  
----  
YOUR DATA WILL BE LOST  
Result:  
A message appears, indicating that any channels  
already preset on your VCR will be deleted.  
The station name is set automatically from the broadcast signal.  
1
2
3
4
5
PRESS OK TO CONTINUE  
10 To change the programmes name, press the ❿ꢀbutton.  
MENU TO EXIT  
Result:  
The first letter of the name flashes.  
5
Press OK to start the auto scanning.  
11 To...  
Then...  
Result:  
The PLEASE WAIT indication flashes on the  
television screen.  
œ❷  
SWAPPING:OK  
MENU  
DELETE:CLR/RST  
Select a character  
in the name  
Press the  
required character is displayed  
(letters, numbers or -character).  
œ
or  
button until the  
The first frequency band is scanned and the first  
station found is displayed and stored.  
The VCR then searches for the second station and  
so on.  
AUTO SET UP  
PLEASE WAIT  
Move to the next or  
previous character  
Press the  
respectively.  
or  
buttons  
MANUAL TUNING  
**  
**  
When the automatic scanning procedure has  
finished, the VCR switches automatically to pro-  
gramme 1.  
PR  
: 1  
CH  
: ---  
: -  
12 If you...  
Then...  
Press the corresponding  
2%  
MFT  
NAME  
I--------------------I  
: ----  
Wish to store the  
station displayed  
œ
or ❷ꢀbuttons,  
The number of stations automatically stored by the VCR  
depends on the number of stations that it has found.  
until the MFT is selected.  
END:MENU  
Press the or buttons to adjust the  
œ❷  
➛❿  
MEMORY:OK  
END:MENU  
picture, if necessary.  
Press OK to store the station  
6
If you wish to cancel the auto scanning before the end, press the  
MENU button three times to exit the menu.  
Do not wish to  
store the station  
displayed  
Press the corresponding  
œ
or ❷ꢀbuttons,  
until the CH is selected.  
The time and date are set automatically from the  
broadcast signal. If the signal is weak or ghosting  
occurs, the time and date may not be set automati-  
cally. In this case, they should be set manually (see  
page 16).  
Press the  
or  
buttons to go on  
scanning the frequency band and display  
the next station  
Go back to the beginning of Step 12  
13 Repeat this procedure from Step  
6
onwards, until all the required  
Once the auto scanning procedure has finished, some  
stations may have been stored more than once; select  
the stations with the best reception and delete the  
ones no longer required (see page 20).  
stations have been stored.  
14 On completion, press the MENU button three times to exit the  
menu.  
18  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cle a rin g a Pre se t Sta tio n  
Ch a n g in g th e Pre se t Sta tio n Ta b le  
GB  
GB  
You can rearrange the Station Table and give different programme  
numbers to the stations listed according to your own preferences.  
If you have stored a TV station:  
That you do not require  
At the wrong programme position  
1
2
Press the MENU button on the remote control.  
INSTALL  
OPTIONS
PROG  
INSTALL  
OPTIONS
PROG  
you can cancel it.  
Press the corresponding  
œ
,
or  
,
buttons to select the  
CLOCK  
BONUS  
CLOCK  
BONUS  
INSTALLATIONoption.  
INSTALLATION  
1
2
Press the MENU button on the remote control.  
INSTALLATION  
3
4
Press the OK button to select this option.  
Press the corresponding  
œ,  
or  
,
buttons to select the  
Result:  
The INSTALLATIONmenu is displayed.  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
INSTALLATIONoption.  
Press the  
And then press the  
Result:  
œ
or  
buttons to select MANUAL SET UPoption.  
button to select this option.  
The TV STATION TABLEmenu is displayed.  
3
4
5
6
Press the OK button to select this option.  
Result:  
The INSTALLATIONmenu is displayed.  
INSTALL  
INSTALL  
AUTO SET UP  
MANUAL SET UP  
VCR OUTPUT CH :CH60  
AUTO SET UP  
MANUAL SET UP  
VCR OUTPUT CH :CH60  
Press the corresponding  
UPoption is selected.  
œ
or  
buttons, until the MANUAL SET  
5
6
Press the corresponding  
œ
or  
buttons, until the required preset  
TV programme is selected.  
Result:  
The selected station is displayed at the same time on  
the television screen.  
Press the  
Result:  
button to select this option.  
The TV STATION TABLEmenu is displayed.  
To change the programme number assigned to a station press the  
OK button on the remote control. (For example, To move a TV  
station in programme 1 to programme 3)  
œ❷  
END:MENU  
œ❷  
END:MENU  
Press the corresponding  
œ
or  
buttons, until the required preset  
TV station (PR) is selected.  
7
8
9
Press the  
press OK again to swap the position.  
œ
or  
buttons to select required position. And then  
7
8
Press the CLR/RST button.  
TV STATION TABLE  
**  
**  
TV STATION TABLE  
**  
**  
PR  
CH  
27  
--  
--  
--  
--  
NAME  
CAEB  
----  
----  
----  
----  
PR  
CH  
27  
--  
--  
--  
--  
NAME  
CAEB  
----  
----  
----  
----  
Repeat the same procedure from Step  
required stations have been cleared.  
6
onwards until all the  
1
2
3
4
5
You can modify this station by repeating the same procedure from  
1
2
3
4
5
Step  
5
onwards.  
9
On completion, press the MENU button three times to exit the  
menu.  
On completion, press the MENU button three times to exit the  
menu.  
œ❷  
SWAPPING:OK  
œ❷  
SWAPPING:OK  
DELETE:CLR/RST  
MENU  
MENU  
TV STATION TABLE  
**  
**  
PR  
CH  
--  
--  
27  
--  
--  
NAME  
----  
----  
CAEB  
----  
----  
1
2
3
4
5
œ❷  
SWAPPING:OK  
MENU  
20  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(SV-6 6 5 B/ SV-6 6 1 B/ SV-6 6 2 B/ SV-6 6 1 I O n ly )  
Se le ctin g th e Ca sse tte Ty p e  
N ICAM  
GB  
GB  
NICAM programmes are divided into 3 types. NICAM Stereo,  
NICAM Mono and Bilingual (transmission in another language).  
NICAM programmes are always accompanied by a standard mono  
sound broadcast and you can select the desired sound.  
Please refer to page 33.  
If you wish to use the tape counter to display the time remaining on  
a cassette, you must indicate the type of cassette inserted.  
(SV-665B/SV-661B/SV-662B/SV-661I)  
1
2
Press MENU on the remote control.  
PTIONS  
Result:  
The programming menu is displayed.  
OPTIONS  
INSTALL  
PROG  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
:E180  
:AUTO  
:AUTO  
:ON  
Press the corresponding  
œ,  
or  
,
buttons to select the  
1
2
Press MENU on the remote control.  
CLOCK  
BONUS  
USER SEToption.  
Result:  
The programming menu is displayed.  
USER SET  
ECO. MODE  
IPC  
:OFF  
:ON  
3
4
Press the OK button to select this option.  
Press the corresponding  
œ,  
or  
,
buttons to select the  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
œ❷  
END:MENU  
USER SEToption.  
Press the corresponding  
œ
or  
buttons, until the TAPE  
SELECToption is selected.  
3
4
5
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
(SV-265B/SV-261B/SV-262B/SV-261I)  
5
Press the  
correct cassette length is displayed.  
or  
buttons as many times as required, until the  
PTIONS  
OSD  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
ECO. MODE  
IPC  
:ON  
Press the corresponding  
is selected.  
œ
or  
buttons, until the NICAMoption  
:E180  
:AUTO  
:AUTO  
:ON  
PTIONS  
E180  
E 300  
E240  
E260  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:OFF  
:ON  
To...  
Press  
or , until...  
:OFF  
:ON  
6
Press MENU twice to exit the menu.  
Mono mode  
OFFis displayed.  
œ❷  
END:MENU  
OFF: Only set at this position to record the  
standard mono sound during a  
NICAM broadcast if the stereo sound  
is distorted due to inferior reception  
conditions.  
œ❷  
END:MENU  
NICAM mode  
ONis displayed.  
ON: Normally set at this position.  
Se le ctin g th e Re co rd in g Sp e e d  
6
On completion, press MENU twice to exit the menu.  
You can record a cassette at two different speeds:  
SP (Standard Play)  
T
ype  
Recording Time (in SP)  
180 mins. or 3 hours  
240 mins. or 4 hours  
LP (Long Play)  
E-180  
E-240  
E-260  
In Long Play modes:  
Each cassette lasts twice as long  
260 mins. or  
The recording is of a slightly lower quality  
4 hours and 20 mins.  
E-300  
300 mins. or 5 hours  
To record a cassette...  
Press the SPEED button on the  
remote control, until...  
OK  
In standard play mode  
In long play mode  
SPis displayed.  
LPis displayed.  
SPEED  
DUB  
TV/VCR  
TIMER  
22  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pro te ctin g a Re co rd e d Ca sse tte  
Re co rd in g a Pro g ra m m e w ith Au to m a tic Sto p  
GB  
GB  
Video cassettes have a safety tab to prevent accidental erasure.  
When this tab has been removed, you cannot record on the tape.  
This function enables you to record up to nine hours (LP) of  
programmes.  
Your VCR stops automatically after the requested length of time.  
1
2
If you wish to protect a cassette, break off the tab using a small  
screwdriver.  
1
2
Switch on the television.  
To re-record over a protected cassette (safety tab broken), cover  
the hole with adhesive tape.  
To monitor the programme being recorded, select the television  
channel reserved for use with your VCR (or the AV input if used).  
1
3
3
Insert the cassette on which the programme is to be recorded,  
with the window visible and the safety tab intact or the opening  
covered with adhesive tape.  
(SV-661B/SV-662B/  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
Result:  
The VCR is switched on automatically.  
(SV-665B)  
Re co rd in g a Pro g ra m m e Im m e d ia te ly  
4
Select:  
T
IPC  
INPUT  
VCR  
INPUT  
The station to be recorded using the PROG/TRK (  
PROG (  
or  
œ
or  
) /  
œ
or  
)
buttons  
4
4
RAT  
REAT  
Before recording a programme, you must have preset the corres-  
ponding station (unless you are recording via an external video  
source). If you have not done so, refer to pages 18 and 19.  
(SV-661B/SV-662B/  
DISPLA  
DISP./  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
The AV1, AV2 or AUX (SV-665B/SV-661B/SV-662B/  
K
PROG  
PROG/TRK  
SV-651I only) source using the INPUT button for a satellite  
tuner or external video source  
Result:  
(SV-665B)  
1
2
Switch on the television.  
T
The channel number is displayed and the programme  
can be seen on the television.  
IPC  
INPUT  
VCR  
INPUT  
4
4
To monitor the programme being recorded, select the television  
channel reserved for use with your VCR (or the AV input if used).  
4
4
RAT  
REAT  
5
6
Select the recording speed by pressing the SPEED button as  
many times as required (see page 22).  
DISPLA  
DISP./  
3
Insert the cassette on which the programme is to be recorded,  
with the window visible and the safety tab intact or the opening  
covered with adhesive tape.  
K
PROG  
PROG/TRK  
Hold the REC button down for a while to start recording.  
Result:  
SPEED  
DUB  
TV/VCR  
TIMER  
The record indicator appears on the television screen  
and VCR display. An index is recorded on the tape  
(see page 36).  
Result:  
The VCR is switched on automatically.  
4
4
5
4
Select:  
The station to be recorded using the PROG/TRK (  
PROG (  
or  
œ
or  
) /  
œ
or  
)
buttons  
7
8
Press the REC button several times to increase the recording time  
in:  
30-minute intervals up to four hours  
1-hour intervals up to nine hours (LP)  
The AV1, AV2 or AUX (SV-665B/SV-661B/SV-662B/  
SV-661I only) source using the INPUT button for a satellite  
tuner or external video source  
SPEED  
DUB  
TV/VCR  
TIMER  
Result:  
The length is displayed on the television displays. The  
selected programme is recorded for the length of time  
requested. At the end of that time, the VCR stops  
recording automatically.  
Result:  
The station number is displayed and the programme  
can be seen on the television.  
5
REC  
MENU  
5
6
Select the recording speed by pressing the SPEED button as  
many times as required (see page 22).  
6
If you wish to cancel the recording before the end, press  
VCR STANDBY/ON (STANDBY/ON).  
TRK  
PROG  
Hold REC down for a while to start recording.  
OK  
Result:  
The record indicator appears on the television and VCR  
display. An index is recorded on the tape (see page 36).  
If the end of the tape is reached while recording:  
The recording stops  
The VCR automatically turns off  
7
To stop recording, press once.  
7
REC  
MENU  
If your VCR ejects the cassette when you start  
recording, check to make sure that the cassette’s  
safety tab is intact or that the opening (created by a  
broken safety tab) is covered with adhesive tape.  
LENGTH 2:30  
6
SET LENGTH :  
PRESS REC  
If you reach the end of the tape while recording, the  
cassette rewinds automatically.  
24  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mo d ify in g VIDEO PLUS+ Pro g ra m m in g  
Using the VIDEOPLUS+ Fea ture (SV-665B/ SV-265B Only)  
(V-6 6 5 B/ SV-2 6 5 B O n ly )  
GB  
GB  
Before presetting your VCR:  
If you wish to correct the programme displayed or modify certain elements, such as the recording  
speed, you can do so before you press MENU a second time to confirm.  
Switch on both the television and your VCR  
Check that the date and time are correct  
Insert the cassette on which the programme is to be  
If you wish to...  
Then...  
recorded (safety tab intact)  
SPEED  
DUB  
TV/VCR  
TIMER  
Select an input source other  
Press the  
or  
buttons, until the PRselection flashes.  
Up to six programmes can be preset.  
than the tuner (AV1, AV2 or  
Press the INPUT button one or more times to change the  
input source selection.  
1
AUX (SV-665B only)  
)
1
Press the TIMER button.  
Result:  
The TIMER METHODis displayed.  
Result:  
The programme number is replaced by:  
The AV1, AV2 or AUX (SV-665B only)  
source using the INPUT button for a satellite tuner  
or external video source  
2
3
Press the corresponding  
option is selected.  
œ
or  
buttons, until the VIDEOPLUS  
Press the ❿ꢀbutton to select VIDEOPLUS  
.
TIMER METHOD  
**  
**  
The input source must be selected before changing any  
other value.  
Result:  
A message is displayed to allow you to enter the  
VIDEOPLUS+ code.  
STANDARD  
VIDEOPLUS  
Record a programme every day  
Press the  
or  
or  
buttons, until the DAYselection flashes.  
buttons, until the DLY(Daily) value is  
If all six programmes have been set, the message TIMER  
IS FULL is displayed. Refer to page 29 if you wish to  
cancel a preset recording.  
(Monday to Sunday) at the same time  
Press the  
displayed.  
œ
œ❷  
END:MENU  
Record a programme every week  
Press the  
Press the  
or  
or  
buttons, until the DAYselection flashes.  
buttons, until the W-(Week) value is  
4
5
Press the numeric buttons to enter the code opposite the  
programme that you wish to record in your television magazine.  
on the same day and at the same time  
œ
If you wish to correct the VIDEOPLUS+ code that you are  
entering:  
displayed, followed by the required day.  
Example: W-SA(Weekly Saturday)  
VIDEOPLUS  
CODE ---------  
Press the  
cleared  
button until the digit to be corrected is  
Extend the recording time  
Select the recording speed  
Press the  
Press the  
time.  
or  
or  
buttons, until the STOPselection flashes.  
buttons to increase or decrease the stop  
Enter the correct digit  
œ
Press the MENU button.  
Result: The information concerning the programme is displayed.  
CODE:0-9  
CORRECT:  
END:MENU  
Press the  
or  
or  
buttons, until the recording speed selection  
buttons until the correct indication is  
When using the VIDEOPLUS+ function for the first time with  
stored stations, the programme number flashes. This one  
time, you must enter the station number manually by  
flashes.  
Press the  
displayed:  
œ
pressing the  
œ
or  
buttons. Refer to the following page if:  
AUTO(Auto Tape Speed Select) : see page 28  
SP(Standard Play)  
LP(Long Play)  
1/JAN WED  
21:28  
PROG  
The programme number or times flash  
You wish to modify the programme  
PR DAY STARTSTOP  
V/P  
1 WE 1 12:0012:50SP ON  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:-- --:---- -  
œ❷ ➛❿  
6
7
If the programme and times are correct, press the MENU button.  
Select the PDC recording  
Press the  
Press the  
or  
or  
buttons, until the V/P selection flashes.  
buttons until the “ON” indication is displayed.  
Press the VCR STANDBY/ON (STANDBY/ON) button to activate  
the timer.  
œ
Do not select PDC unless you are sure the programme you  
DELETE:CLR/RST  
MENU  
8
Refer to page 29 if you wish to:  
wish to record is broadcast with PDC. If you do set PDC ON  
(by selecting “ON” in the right - hand column on the screen),  
then you must set up the start-time EXACTLY according to  
the published TV schedule. Otherwise the timer recording  
won’t take place.  
Check that your VCR has been programmed correctly  
Cancel a preset recording  
(SV-665B)  
(SV-265B)  
The numbers next to each TV programme listing are  
VIDEOPLUS+ code numbers, which allow you to  
programme your videorecorder instantly with the remote  
control. Tap in the VIDEOPLUS+ code for the programme  
you wish to record.  
STANDBY/ON  
VCR STANDBY/ON  
S
S
7
7
SH  
SH  
™ VIDEOPLUS+ is a trademark of Gemstar Development Corporation. The VIDEOPLUS+  
system is manufactured under licence from Gemstar Development Corporation.  
26  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Usin g th e Tim e r Pro g ra m m in g Fe a tu re  
Ch e ck in g a Pre se t Re co rd in g  
GB  
GB  
The Timer Programming feature allows you to preset the VCR to  
record a programme up to one month before that programme is to  
be broadcast. Up to six programmes can be preset.  
You can check your preset recordings:  
(SV-665B/SV-265B)  
When you have finished presetting the VCR  
If you have forgotten which programmes will be  
TIMER METHOD  
**  
**  
Before presetting a recording, check that the date and  
time are correct.  
recorded  
STANDARD  
VIDEOPLUS  
1/JAN WED  
21:28  
PROG  
PR DAY STARTSTOP  
V/P  
1
- Insert the cassette. Press the TIMER button.  
Press the or buttons to select the STANDARD option and  
1 WE 1 12:0012:50SP ON  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:-- --:---- -  
1
- Insert the cassette. Press the TIMER button.  
Press the or buttons to select the STANDARD option and  
œ
œ
then press the ❿ꢀbutton or,  
then press the ❿ꢀbutton or,  
œ❷  
END:MENU  
Press MENU on the remote control.  
Result: The programming menu is displayed.  
Press MENU on the remote control.  
Result: The programming menu is displayed.  
œ❷  
SET:❿  
MENU  
DELETE:CLR/RST  
Press the OK button to select TIMER PROGRAMMINGoption.  
Result: The TIMER PROGRAMMINGmenu is displayed.  
Press the OK button to select TIMER PROGRAMMINGoption.  
Result: The TIMER PROGRAMMINGmenu is displayed.  
2
3
Press the  
œ
or  
buttons to select the required programme.  
2
3
Press ❿ꢀto select the input source.  
OPTIONS INSTALL  
PROG  
Select the required station by pressing the  
œ,  
buttons or INPUT  
Press the  
or  
buttons to select and change any values as  
CLOCK  
BONUS  
to select the AV1, AV2 or AUX (SV-665B/SV-661B/SV-662B/  
SV-661I only) input sources.  
required. For more details, refer to the previous page.  
TIMER PROGRAMMING  
4
On completion, press MENU twice.  
4
5
6
Press  
Select the required day by pressing the  
Press to select the recording start time.  
Select the required hour value by pressing the  
Press to select the minutes.  
Select the required minute value by pressing the  
to select the recording day.  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
œ
or  
buttons.  
7
8
9
œ
or  
buttons.  
1/JAN WED  
21:28  
PROG  
PR DAY STARTSTOP  
V/P  
1 WE 1 12:0012:50SP ON  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:-- --:---- -  
œ❷ ➛❿  
œ
or  
buttons.  
Ca n ce llin g a Pre se t Re co rd in g  
10 Press  
to select the recording end time.  
11 Select the required recording end time by pressing the  
œ
or  
DELETE:CLR/RST  
MENU  
buttons, following the same procedure as when selecting the  
recording start time.  
You can cancel any programmes that are:  
Incorrect  
1/JAN WED  
21:28  
PROG  
12 Press  
to select the recording speed.  
(SV-661B/SV-662B/  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
PR DAY STARTSTOP  
V/P  
No longer required  
1 WE 1 12:0012:50SP ON  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:----:---- -  
-- ------:-- --:---- -  
13 Press the  
œ
or  
buttons to select the SP(Standard Play), LP  
(SV-665B)  
(Long Play), AUTO(Auto Tape Speed Select) recording speeds.  
14 Press to select the PDC recording mode.  
15 Press the or buttons to toggle between the PDC mode  
1
- Insert the cassette. Press the TIMER button.  
Press the or buttons to select the STANDARD option and  
œ
then press the ❿ꢀbutton or,  
œ❷  
SET:❿  
MENU  
STANDBY/ON  
VCR STANDBY/ON  
DELETE:CLR/RST  
Press MENU on the remote control.  
Result: The programming menu is displayed.  
œ
(marked ON) and the non-PDC mode (marked -).  
Press the OK button to select TIMER PROGRAMMINGoption.  
Result: The TIMER PROGRAMMINGmenu is displayed.  
S
S
(SV-661B/SV-662B/  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
17  
17  
16 When you have finished, press the MENU button.  
17 Press the VCR STANDBY/ON (STANDBY/ON) button to activate  
2
3
Select the programme to be cancelled by pressing the  
buttons.  
œ
or  
(SV-665B)  
the timer.  
SH  
SH  
Result:  
Before starting recording, the VCR compares the timer  
duration with the remaining time on the cassette.  
Press the CLR/RST button to cancel the selected programme.  
CLR/RST  
-/--  
F.ADV  
CLR/RST  
A.TRK  
F.ADV  
Result:  
All the recording information is deleted and the broad-  
cast will not be recorded.  
Auto Tape Speed Select. The VCR’s “Auto Tape Speed  
Select” function compares the duration of the timer  
recording to the actual recording time remaining on the  
tape loaded. If there is insufficient tape to complete a  
timer recording in AUTO mode, the VCR automatically  
switches to LP mode to record the whole programme.  
SELT  
TV  
VCR  
3
3
IPC  
4
On completion, press MENU twice.  
AUDIO  
AUDIO  
28  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
In te llig e n t Pictu re Co n tro l  
Pla y in g a Ca sse tte  
GB  
GB  
The Intelligent Picture Control Feature allows you to adjust the  
sharpness of the image automatically, according to your own  
preferences.  
This function allows you to play back any pre-recorded cassette.  
(SV-665B/SV-661B/SV-662B/SV-661I)  
1
2
Switch on both the television and your VCR.  
1
During playback, press the MENU button on the remote control.  
Result: The programming menu is displayed.  
PTIONS  
Insert the video cassette to be played. If the safety tab on the  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
:E180  
:AUTO  
:AUTO  
:ON  
cassette is intact, press ll  
.
2
3
Press the corresponding  
œ,  
or  
,
buttons to select the  
Otherwise, the cassette is played automatically.  
USER SEToption.  
2
3
REC  
MENU  
ECO. MODE  
IPC  
:OFF  
:ON  
END:MENU  
When a cassette is loaded, the tape position is optimized  
automatically to reduce disturbance (Digital Auto Tracking).  
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
œ❷  
When playing a cassette, if the end of the tape is reached,  
the cassette is rewound automatically.  
NTSC tapes can be played back but cannot be recorded  
with this VCR.  
4
5
Press the corresponding  
selected.  
œ
or  
buttons, until the IPCoption is  
(SV-265B/SV-261B/SV-262B/SV-261I)  
Press the button to select the IPC (intelligent picture control)  
option.  
3
To...  
Then press...  
When intelligent picture control mode is ON, the sharpness  
Stop the playback  
Eject the cassette  
(STOP).  
PTIONS  
of the image is adjusted automatically.  
OSD  
:ON  
(EJECT).  
TAPE SELECT  
COLOUR SYSTEM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:OFF  
:ON  
6
7
To adjust the sharpness manually, select Intelligent Picture  
Control mode OFF  
.
Press the or buttons until the picture is displayed according to  
your preferences.  
Ad ju stin g Pictu re Alig n m e n t Au to m a tica lly (SV-6 6 1 B/  
SV-662B/ SV-661I/ SV-265B/ SV-261B/ SV-262B/ SV-261I Only)  
œ❷  
END:MENU  
If you do not press a button within ten seconds, the  
PICTUREmenu disappears automatically.  
8
On completion, press the MENU button again.  
The Picture Alignment feature enables you to optimize the tape  
position automatically to obtain the best possible picture.  
A.TRK  
IPC  
INPUT  
In te llig e n t Pictu re Co n tro l (SV-6 6 1 B/ SV-6 6 2 B/  
When noise bars or streaks appear during playback, adjust picture  
alignment by pressing the A.TRK button.  
REPEAT  
SV-6 6 1 I/ SV-2 6 5 B/ SV-2 6 1 B/ SV-2 6 2 B/ SV-2 6 1 I O n ly )  
Result:  
The tracking bar appears.  
The picture is automatically adjusted.  
The tracking bar disappears when digital auto tracking has  
been completed.  
AUDIO  
DISPLAY  
TRK  
PROG  
CLR/RST  
F.ADV  
IPC  
INDEX  
INPUT  
1
During playback, press the IPC button.  
Result:  
The PICTUREmenu is displayed.  
button to turn the IPC (Intelligent Picture Control)  
A.TRK  
2
Press the  
option ONand OFF  
.
REPEAT  
1
When Intelligent Picture Control mode is ON, the sharpness  
of the image is adjusted automatically.  
Ad ju stin g Pictu re Alig n m e n t Ma n u a lly  
AUDIO  
DISPLAY  
TRK  
PROG  
3
4
To adjust the sharpness manually, press the  
IPC mode OFF  
The horizontal picture adjusting appears.  
Press the or buttons until the picture is displayed according to  
your preferences.  
button to turn the  
(SV-661B/SV-662B/  
The Picture Adjustment feature allows you to adjust the alignment  
manually to obtain the best possible picture.  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
.
(SV-665B)  
PICTURE  
**  
**  
VCR  
INPUT  
.TRK  
IPC  
When noise bars or streaks appear during playback, adjust alignment  
manually by pressing the PROG/TRK (  
œ
or  
) / TRK  
(
or  
)
buttons  
IPC : OFF  
SOFTEN SHARPEN  
REPT  
DISP./  
If you do not press a button within ten seconds, the  
PICTUREmenu disappears automatically.  
until the picture is clear and stable.  
IO  
-------- -----  
*
PROG/TRK  
5
On completion, press the IPC button again.  
TRK  
PROG  
Result:  
The tracking bar appears.  
The image is adjusted.  
The tracking bar disappears when you release the button.  
➛❿  
ON/OFF:❷  
30  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Audio Output Mode (SV-6 6 5 B/ SV-6 6 1 B/  
Forma t 16:9 (Wide Screen) (SV-665B/ SV-661B/ SV-662B/ SV-661I Only)  
SV-6 6 2 B/ SV-6 6 1 I Only)  
Your VCR can automatically play Wide Screen format prerecorded  
tapes. It can also record Wide Screen format programmes received  
from sources such as a satellite receiver.  
GB  
GB  
When monitoring a TV programme or playing back a Hi-Fi  
recorded video tape, press the AUDIO button to select a desired  
sound output. As the AUDIO button is pressed, the sound output  
Connect equipment compatible with Wide Screen to the VCR  
using the 21 pin SCART cable.  
REPEAT  
DISP./  
and the indicator change as below:  
OPTIONS  
INSTALL  
PROG  
AUDIO  
1
2
3
4
5
Press MENU on the remote control.  
VOL  
PROG/TRK  
Standard  
sound  
Sound type  
OSD display  
CLOCK  
BONUS  
Result:  
The programming menu is displayed.  
Stereo sound  
Bilingual sound  
USER SET  
broadcast  
Press the corresponding  
œ,  
or  
,
buttons to select the  
Channel I (MAIN)  
heard from the left  
speaker, channel  
II (SUB) heard  
from the right  
USER SEToption.  
Heard in stereo.  
(left channel and  
right channel)  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
Heard in  
monaural.  
L R  
Press the corresponding or buttons, until the  
œ
FORMAT 16:9option is selected.  
speaker.  
Press the ❿ꢀꢀbutton to select AUTOONOFF  
.
PTIONS  
Channel I (MAIN)  
heard from both  
the left and the  
right speakers.  
Left channel heard  
from both the left  
and right  
OSD  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
:ON  
Heard in  
monaural.  
AUTO  
Set when you use a wide TV. The VCR automatically  
:E180  
:AUTO  
:AUTO  
:ON  
L
detects if programmes being played back or recorded  
are in normal or Wide Screen format.  
speakers.  
ECO. MODE  
IPC  
:OFF  
:ON  
END:MENU  
ON  
The VCR always plays back and records in 16:9 Wide  
Screen format. Set if the VCR cannot detect Wide  
Screen TV programmes with AUTOset.  
Channel II-(SUB)  
heard from both  
the left and the  
right speakers.  
Right channel  
heard from both  
the left and right  
speakers.  
Heard in  
monaural.  
œ❷  
R
OFF  
Set if you do not use a Wide Screen TV.  
Sound mixed the left and right channels, and the  
normal audio track.  
6
On completion, press MENU twice to exit the menu.  
MIX  
Channel I (MAIN)  
Se le ctin g th e Co lo u r Mo d e  
heard from both  
the left and the  
right speakers.  
Heard in  
monaural.  
Heard in  
monaural.  
MONO  
Before recording or playing back a cassette, you can select the  
required system standard.  
(SV-665B/SV-661B/SV-662B/SV-661I)  
Otherwise, the system automatically selects the reception standard  
when you select AUTO.  
When playing back a cassette, the standard is  
automatically selected by the VCR.  
PTIONS  
Se le ctin g th e Au d io Mu te Mo d e (SV-2 6 5 B/ SV-2 6 1 B/  
SV-2 6 2 B/ SV-2 6 1 I O n ly )  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
:E180  
:AUTO  
:AUTO  
:ON  
When you playback an NTSC-recorded tape on this VCR  
make a setting on the colour system according to your TV.  
If your TV is a PAL system only TV, set NTPB.  
If your TV is Multi System TV (NTSC 4.43 compatible), set  
NT4.43 and you can record NT4.43.  
ECO. MODE  
IPC  
:OFF  
:ON  
END:MENU  
You can select the Audio Mute mode.  
œ❷  
REPEAT  
1
2
3
4
Press MENU on the remote control.  
To select the audio mute mode on and off, simply press the AUDIO button  
on the remote control.  
Result:  
The programming menu is displayed.  
AUDIO  
DISPLAY  
(SV-265B/SV-261B/SV-262B/SV-261I)  
TRK  
PROG  
Press the corresponding  
œ,  
or  
,
buttons to select the  
USER SEToption.  
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
PTIONS  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:OFF  
:ON  
Press the corresponding or buttons, until the  
COLOUR SYSTEMoption is selected.  
Press the button to select AUTOPAL★★ B/W.  
œ
5
œ❷  
END:MENU  
AUTO When playing back a cassette, the system standard is  
automatically selected by the VCR.  
B/W Black and White  
6
On completion, press MENU twice to exit the menu.  
32  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pla y in g a Ca sse tte in Slo w Mo tio n (SV-6 6 5 B/  
SV-6 6 1 B/ SV-6 6 2 B/ SV-6 6 1 I O n ly )  
Pla y in g a Se q u e n ce Fra m e b y Fra m e  
GB  
GB  
You can:  
You can play a cassette in slow motion.  
Stop the cassette at a given frame (image)  
Advance one frame at a time  
No sound is heard when playing back a cassette in slow  
motion.  
TRK  
PROG  
No sound is heard when playing back frame by frame.  
SLOW  
1
2
Press:  
1
2
Press:  
ll to start playing the cassette  
SHUTTLE  
V-LOCK  
SLOW  
ll to start playing the cassette  
ll to stop the tape at a given frame  
to advance frame by frame  
1
1
SLOW (  
) as many times as required to decrease or  
REC  
MENU  
1
increase the speed respectively  
F.ADV ( F.ADV  
)
o return to the normal speed, press the ll  
T button twice.  
To return to normal playback, press ll  
.
When playing back in slow motion, picture interference may occur.  
Press the PROG/TRK (  
minimize this effect.  
œ
or  
) / TRK  
(
or  
)
buttons to  
(SV-661B/SV-662B/  
SV-661I)  
When you have been using the Frame-by-Frame function  
for more than about five minutes, the VCR will auto-  
matically play to protect the cassette and video heads.  
(SV-665B)  
.TRK  
IPC  
VCR  
INPUT  
When you have been using the Slow Motion function for  
more than about five minutes, the VCR will automatically  
play to protect the:  
2
RET  
2
Vertical stability: When playing back frame by frame,  
DISP./  
interference may be seen on the screen. Press the  
IO  
Cassette  
Video heads  
V-LOCK  
PROG/TRK  
TRK  
PROG  
V-LOCK (  
) buttons to minimize this effect.  
2
2
Pictu re Se a rch , Fa st Fo rw a rd / Re w in d  
Picture Search enables you to Fast Forward or Rewind and look for  
a particular part of a tape.  
1
Press PLAY, the VCR will enter normal play mode. While in play,  
press and release the (or ) button. The VCR will search at 5  
times the normal playback speed.  
2
3
To return to normal playback mode, press the  
button.  
II  
If you press and HOLD down the (or ) button the VCR will  
search at 9 times the normal speed. Releasing the button will  
return the VCR to search at 5 times the normal speed. To return to  
normal playback mode, press the  
II  
button.  
4
5
6
Whilst in Picture Search mode, if you press the button again,  
the VCR will enter normal Fast Forward mode.  
Likewise, whilst in Picture Search mode, if you press the ➛  
button again, the VCR will enter normal Rewind mode.  
If, when Rewinding () or Fast Forwarding (), you press the ➛  
(or ) button, the VCR will enter the Picture Search mode.  
34  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Se a rch in g fo r a Sp e cific Se q u e n ce  
Au to Re p e a t Pla y  
GB  
GB  
(SV-665B/SV-265B)  
You can set repeat play to repeat the tape continuously from  
beginning to end.  
Each time you record a cassette on this VCR, an “index” is  
automatically marked on the tape when recording starts.  
BONUS  
V-LOCK  
The Search function allows you to fast-forward or rewind to a  
specific index and start playback from that point. Depending on the  
direction selected, the indexes are numbered as follows:  
VIDEOPLUS EXTEND :OFF  
1
2
3
4
5
Press MENU on the remote control.  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
Result:  
The programming menu is displayed.  
:OFF  
CLR/RST  
A.TRK  
F.ADV  
INDEX  
INTERVAL REPEAT : 5  
Press the corresponding  
œ,  
or  
,
buttons to select the  
EASY OPERATIONoption.  
1
Prev  
Seq.  
Seq. being Next  
played Seq.  
IPC  
INPUT  
œ❷  
END:MENU  
Press the OK button to select this option.  
etc.  
etc.  
Result:  
The EASY OPERATIONmenu is displayed.  
REPEAT  
2
1
1
2
(SV-661B/SV-662B/SV-661I/SV-261B/  
SV-262B/SV-261I)  
Press the corresponding  
œ
or  
buttons, until the  
REPEAT PLAYoption is selected.  
This VCR uses a standard indexing system (VISS). As a  
result, it will recognize any indexes marked by other  
VCRs using the same system and vice versa.  
To...  
Press  
or , until...  
BONUS  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
:OFF  
INDEX:  
➛ꢀꢀꢀꢀꢀ❿  
Repeat play  
ONis displayed.  
INTRO SCAN  
INTERVAL REPEAT : 5  
Do not wish to repeat play  
OFFis displayed.  
1
2
To search for a specific index, press INDEX.  
Press the ➛  
6
On completion, press MENU twice to exit the menu.  
œ❷  
END:MENU  
❿❿  
or  
buttons depending on the direction  
where your desired programme is located.  
3
4
When an Index mark is found the VCR will playback the tape for 5  
seconds, after which it will continue searching for the next Index  
mark.  
In te rva l Re p e a t Pla y  
INDEX SEARCH:  
ꢀꢀꢀꢀ+01  
If you want to watch the tape from a particular Index, simply press  
You can set Interval Repeat Play so that the cassette is repeated a  
number of times according to a specified set interval.  
PROG  
OPTIONS INSTALL  
BONUS  
II  
.
CLOCK  
1
2
3
Press MENU on the remote control.  
Index Skip Search:  
EASY OPERATION  
Result:  
The programming menu is displayed.  
This feature will enable you to fast forward/rewind to a specific  
point on a tape: E.g. if you have recorded 3 different programmes  
on a tape and you have rewound the tape to the beginning, by  
using this feature you can go directly to the start of programme 2  
simply by pressing the INDEX button.  
Press the corresponding  
œ,  
or  
,
buttons to select the  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
EASY OPERATIONoption.  
Press the OK button to select this option.  
(SV-665B/SV-265B)  
Result:  
The EASY OPERATIONmenu is displayed.  
4
5
Press the corresponding  
NO. OF INTERVAL REPEAToption is selected.  
œ
or  
buttons, until the  
BONUS  
1
2
Press the INDEX to start the Index search.  
Press the ➛  
VIDEOPLUS EXTEND :OFF  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
:OFF  
❿❿  
or  
buttons twice more. This will take  
To...  
Press , until...  
you directly to the start of the desired programme is located.  
INTERVAL REPEAT : 5  
Interval Repeat Play  
5, 10, 15 is displayed.  
(choose an interval repeat of  
5, 10 or 15 times)  
3
4
These Index searches can be made forwards: (press ) or  
backwards: (press ).  
œ❷  
END:MENU  
Cancel Interval Repeat Play  
OFFis displayed.  
To cancel an Index search simply press the  
or  
button.  
II  
(SV-661B/SV-662B/SV-661I/SV-261B/  
SV-262B/SV-261I)  
6
7
On completion, press MENU twice to exit the menu.  
To select Interval Repeat Play during playback, press the  
INPUT/REPEAT button at the desired start point.  
BONUS  
Result:  
INTERVAL REPEAT SETTINGis displayed.  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
:OFF  
Press the INPUT/REPEAT button one more time at the desired  
end point.  
Result:  
INTERVAL REPEAT : 5  
The tape is automatically rewound to the start point.  
INTERVAL REPEATis displayed.  
œ❷  
END:MENU  
36  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEOPLUS+ EXTEND (SV-6 6 5 B/ SV-2 6 5 B Only)  
Co n n e ctin g a n RCA Au d io / Vid e o In p u t Ca b le  
(SV-6 6 5 B/ SV-6 6 1 B/ SV-6 6 2 B/ SV-6 6 1 I O n ly )  
GB  
GB  
To prevent delays or over-runs the VCR has a function called  
Videoplus EXTEND allowing you to extend the recording time by  
up to 60 minutes.  
You can connect other audio/video equipment to your VCR using  
audio/video cables if the appropriate outputs are available on the  
equipment chosen.  
(SV-665B/SV-661B/SV-662B/SV-661I)  
PROG  
OPTIONS INSTALL  
BONUS  
Only use if PDC is not available or set to OFF.  
CLOCK  
Examples: You wish to copy a video cassette with the help of a  
STANDBY/ON  
STANDBY/ON  
1
2
Press the MENU button on the remote control.  
Press the corresponding or buttons to select the  
EASY OPERATIONoption.  
Press the OK button to select this option.  
second VCR (see page 40).  
EJECT  
EJECT  
EASY OPERATION  
You wish to play back and/or copy pictures taken  
œ,  
,
VIDEO  
L
AUDIO  
R
VIDEO  
L
AUDIO  
R
with a camcorder (see page 40).  
œꢀꢀ➛❿ꢀꢀ OK  
END:MENU  
AUX  
AUX  
3
3
4
5
6
Regardless of the type of connection chosen, you  
must always connect the coaxial cable supplied.  
Otherwise, no picture will be visible on the screen  
when the VCR is switched off.  
3
1
Result:  
The EASY OPERATIONmenu is displayed.  
BONUS  
Press the corresponding  
VIDEOPLUS EXTENDoption is selected.  
œ
or  
buttons, until the  
PDC/VPS DEFAULT  
VIDEOPLUS EXTEND :OFF  
:OFF  
Make sure that both the television and the VCR are  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
:OFF  
Press or buttons to set the Videoplus EXTEND time by  
increments of 10 minutes.  
switched off before connecting the cables.  
INTERVAL REPEAT : 5  
To turn off, press or buttons repeatedly until OFFshows.  
1
2
3
Connect one end of the RCA audio/video cable into the VIDEO  
INPUT socket on the front of the VCR.  
œ❷  
END:MENU  
Plug the other end of the audio/video cable into the appropriate  
output connector on the other system (VCR or camcorder).  
Usin g th e Ta p e Co u n te r  
Connect one end of the RCA audio cable supplied into the AUDIO  
INPUT sockets on the front of the VCR.  
The tape counter:  
Take care to respect the colour coding of the left and right  
channels.  
Indicates the elapsed time in the play and record modes  
(hours, minutes and seconds)  
4
Plug the other end of the audio cable into the appropriate output  
connectors on the other system (VCR, camcorder or Hi-Fi sound  
system).  
Is reset when a cassette is inserted in the VCR  
Allows you to find the beginning of a sequence easily  
If the remaining time is to be calculated correctly, you  
must indicate the type of cassette being used.  
0:00:00  
1
2
Insert a cassette in your VCR.  
To set the tape counter to zero at the beginning of a sequence:  
Press DISP./  
or DISPLAY twice to display the counter  
(SV-661B/SV-662B/  
SV-661I/SV-265B/  
SV-261B/SV-262B/  
SV-261I)  
Press CLR/RST when you want to set the tape counter to zero  
3
When you are ready,  
(SV-665B)  
Start playback or Recording.  
Press the button.  
CLR/RST  
-/--  
F.ADV  
INDEX  
CLR/RST  
A.TRK  
F.ADV  
INDEX  
To fast-forward or rewind to the sequence at which the  
counter was set to zero, press or .  
SECT  
TV  
VCR  
INPUT  
IPC  
INPUT  
2
2
REPEAT  
DISP./  
REPEAT  
UDIO  
DIO  
DISPLAY  
Some VCR information, such as the counter, can be  
displayed on the television screen (unless you have  
deactivated the OSD mode; refer to page 17).  
VOL  
PROG/TRK  
TRK  
PROG  
2
2
Press DISP./ or DISPLAY:  
REC  
MENU  
EC  
MENU  
Once to display the current function, programme  
number, recording speed, date, time and counter  
Twice to display the counter only  
Three times to display the time remaining on the  
cassette  
Four times to clear the display  
38  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the TV Buttons on the Rem ote Control (V-665B Only)  
Usin g th e Asse m b le Ed it Fu n ctio n  
This function allows you to start a new recording at a specific  
GB  
GB  
position on the cassette while maintaining a very smooth scene  
change.  
Your VCR remote control will work with Samsung televisions and  
compatible brands.  
1
2
3
Insert the cassette to be edited in your VCR.  
VCR STANDBY/ON  
TV STANDBY/ON  
To determine whether your television is compatible, follow the instructions  
below.  
Press the ll button to start playback.  
SLOW  
When you reach the position from which you wish to start the new  
1
SHUTTLE  
1
2
3
Switch your television on.  
recording, press the ll button.  
2
F.ADV  
V-LOCK  
F.ADV  
REC  
MENU  
4
5
6
Press the  
(
) button again as often as necessary to  
F.ADV  
Point the remote control towards the television.  
2
CLR/
-/--  
INDEX  
advance frame by frame, until the exact recording position is  
located.  
SELECT  
Hold down the TV button and enter the two-figure code  
corresponding to the brand of your television, by pressing the  
appropriate numeric buttons.  
2
TV  
VCR  
INPUT  
While the VCR is in still mode, hold the REC button down for a  
while to activate the Assemble Edit function.  
OK  
CLR/RST  
-/--  
F.ADV  
INDEX  
Result:  
Record symbol flashes in the display.  
Brand  
Codes  
Brand  
Codes  
Select the source from which you wish to record by pressing:  
SELECT  
SAMSUNG  
AKAI  
GRUNDIG  
LOEWE  
01 to 06  
09, 23  
09, 17, 21  
02  
PHILIPS  
SABA  
SONY  
THOMSON  
TOSHIBA  
02, 20, 22  
13, 14, 22 to 24  
15, 16  
13, 14, 24  
07, 16 to 19, 21  
TV  
VCR  
INPUT  
The PROG/TRK (  
television channels  
œ
or  
) / PROG (  
œ
or  
) buttons for  
3
5
REPEAT  
DISP./  
4
★★  
The INPUT button for the AV1, AV2 or AUX (SV-665B/  
SV-661B/SV-662B/SV-661I only) input sources  
AUDIO  
VOL  
PROG/TRK  
PANASONIC  
08, 23 to 27  
7
8
Press the ll button to start recording.  
5
Result: If your television is compatible with the remote control, it  
is switched off. It is now programmed to operate with the  
remote control.  
When you have finished recording, press  
.
TV  
VCR  
INPUT  
REPEAT  
DISP./  
If several codes are indicated for your television brand, try  
each one in turn until you find one that works.  
6
Re co rd in g fro m An o th e r VCR o r Ca m co rd e r  
AUDIO  
VOL  
PROG/TRK  
You can copy a cassette to your VCR from another video source,  
such as another VCR or a camcorder.  
When you change the batteries in the remote control, you  
must reprogramme the code, following the same procedure.  
6
You can then control the television using the following buttons.  
It is an infringement of copyright laws to copy prerecorded  
cassettes or to re-record them in any form without the  
permission of the owners of the corresponding copyright.  
TV  
VCR  
INPUT  
Button  
Function  
REPEAT  
DISP./  
TV STANDBY/ON  
Used to switch the television on and off.  
1
Connect the VCR, from which the cassette is to be copied, to the  
appropriate SCART audio and video input connectors on the rear  
of your VCR.  
AUDIO  
TV or VCR  
Used to switch between the TV and VCR modes.  
VOL  
PROG/TRK  
Only the VOL (+ or –  
)
and TV STANDBY/ON  
You can also use a RCA audio and video cable to connect the AUX  
7
buttons are operational in VCR mode.  
input on the front of your VCR. (SV-665B/SV-661B/SV-662B/  
SV-661I only)  
-/--  
Used to enter a two-figure programme number.  
Example: For programme 12, press -/-- followed  
by numeric buttons 1 and 2.  
2
3
Insert a blank cassette in your VCR.  
Insert the pre-recorded cassette in the other video source (VCR or  
camcorder).  
4
Press the INPUT button to select the appropriate input on your  
INPUT  
Used to select an external source.  
REC  
MENU  
VCR:  
6
AV1 or AV2 (SV-665B/SV-661B/SV-662B/SV-661I only) for  
the SCART input  
VOL + or –  
Used to adjust the volume of the television.  
Used to select the required programme.  
AUX for the RCA input (SV-665B/SV-661B/SV-662B/  
PROG/TRK  
(œor)  
OK  
SV-661I only)  
5
6
7
Start playing back the cassette to be copied.  
DISP./  
Used to switch between an external source and  
the television tuner.  
Hold REC down for a while to start recording on your VCR.  
When you have finished recording, press  
on both VCRs.  
The various functions will not necessarily work on all  
televisions. If you encounter problems, operate the  
television directly.  
If you wish to view the cassette being copied:  
Your VCR must be connected as usual to the  
television (see page 12 for further details)  
40  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Au to Po w e r O ff  
Te ch n ica l Sp e cifica tio n s  
(SV-665B/SV-265B)  
GB  
The Auto Power Off feature automatically turns off your VCR if no  
signal is received and you do not press any button for the selected  
time.  
GB  
BONUS  
Design and specifications are subject to change without notice.  
VIDEOPLUS EXTEND :OFF  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
1
2
3
4
5
Press MENU on the remote control.  
:OFF  
SV-665B/SV-661B  
SV-662B/SV-661I  
Result:  
The programming menu is displayed.  
MODEL  
SV-265B/SV-261B/SV-262B/SV-261I  
INTERVAL REPEAT : 5  
Press the corresponding  
œ,  
or  
,
buttons to select the  
EASY OPERATIONoption.  
Format  
Heads  
VHS PAL standard  
Video: 4 rotary heads  
VHS PAL standard  
Video: 2 rotary heads  
œ❷  
END:MENU  
Press the OK button to select this option.  
Hi-Fi audio: 2 rotary heads  
Audio/Control: 1 stationary head  
Erase: 1 full track erase head  
UHF (SV-665B/SV-661B/SV-662B)  
VHF-I, VHF-III, UHF, (SV-661I)  
lnterband/Hyperband  
(SV-661B/SV-662B/SV-661I/SV-261B/  
SV-262B/SV-261I)  
Result:  
The EASY OPERATIONmenu is displayed.  
Audio/Control: 1 stationary head  
Erase: 1 full track erase head  
UHF (SV-265B/SV-261B/SV-262B)  
VHF-I, VHF-III, UHF,(SV-261I)  
lnterband/Hyperband  
STANDARD I  
FM azimuth recording  
PAL/NT4.43: Down  
converted subcarrier phase shifted  
direct recording  
Press the corresponding  
œ
or  
buttons, until the  
Receiving channel  
AUTO POWER OFFoption is selected.  
BONUS  
AUTO POWER OFF  
REPEAT PLAY  
NO. OF  
:OFF  
:OFF  
Press the  
interval.  
button, until you select the time of Auto Power off  
Television system  
Luminance  
STANDARD I  
FM azimuth recording  
INTERVAL REPEAT : 5  
Colour system  
PAL/NT4.43: Down  
converted subcarrier phase shifted  
direct recording  
OFF 2HOUR 3HOUR  
œ❷  
END:MENU  
NTSC PB on PAL TV  
NTSC PB on PAL TV  
6
On completion, press MENU twice to exit the menu.  
Tape speed  
SP  
LP  
23.39 mm/sec  
11.69 mm/sec  
SP  
LP  
SP  
LP  
23.39 mm/sec  
11.69 mm/sec  
3 hours (E-180 Tape)  
6 hours (E-180 Tape)  
Recording/playback time SP  
LP  
3 hours (E-180 Tape)  
6 hours (E-180 Tape)  
Child Door Lock System (SV-665B/ SV-661B/ SV-662B/ SV-661I/  
SV-265B/ SV-261B/ SV-262B/ SV-261I )  
REW time  
About 60 sec in REW with E-180  
About 60 sec in REW with E-180  
VIDEO  
Input  
Output  
Signal-to-noise ratio  
Horizontal resolution  
With this mechanism you can prevent children from harming  
themselves or the VCR. It stops fingers and small articles from  
entering your VCR.  
0.5 to 2.0 Vp-p; 75 ohm unbalanced 0.5 to 2.0 Vp-p; 75 ohm unbalanced  
1.0 ± 0.2 Vp-p; 75 ohm unbalanced  
Better than 43 dB (SP)  
1.0 ± 0.2 Vp-p; 75 ohm unbalanced  
Better than 43 dB (SP)  
More than 240 lines  
More than 240 lines  
AUDIO  
Input  
Output  
Wow and flutter (WTD)  
Signal-to-noise ratio  
Frequency response  
ECO Mo d e -Re d u cin g Sta n d b y p o w e r co n su m p tio n  
-8 dBm, 47 Kohm unbalanced  
-8 ± 3 dBm, 1 Kohm unbalanced  
0.4% max (SP)  
68 dB min (IHF A filter)  
20Hz - 20kHz  
-8 dBm, 47 Kohm unbalanced  
-8 ± 3 dBm, 1 Kohm unbalanced  
0.4% max (SP)  
42 dB min (IHF A filter)  
100Hz - 8kHz  
(SV-665B/SV-661B/SV-662B/SV-661I)  
Low Power Mode reduces the Standby power consumption of the  
VCR when in Standby mode.  
Useful, for example, when you are away from the house on holiday.  
It saves actually turning the VCR off.  
PTIONS  
OSD  
:ON  
TAPE SELECT  
COLOUR SYSTEM  
FORMAT 16:9  
NICAM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:AUTO  
:ON  
:OFF  
:ON  
Power requirement  
Power consumption  
Operation temperature  
Operation humidity  
Weight  
220-240V~, 50 Hz  
Approx. 17 watts  
41°F-104°F (5°C-40°C)  
10%-75%  
2.8 Kg (net)  
360 x 94 x 240 mm  
220-240V~, 50 Hz  
Approx. 15 watts  
41°F-104°F (5°C-40°C)  
10%-75%  
2.8 Kg (net)  
360 x 94 x 240 mm  
1
2
3
4
5
Press MENU on the remote control.  
Result:  
The programming menu is displayed.  
Press the corresponding  
œ,  
or  
,
buttons to select the  
USER SEToption.  
œ❷  
END:MENU  
Dimensions (WxHxD)  
Press the OK button to select this option.  
Result: The USER SETmenu is displayed.  
(SV-265B/SV-261B/SV-262B/SV-261I)  
Press the corresponding  
is selected.  
œ
or  
buttons, until the ECO. MODE  
PTIONS  
OSD  
:ON  
Press the ❿ꢀbutton to turn LOW(3Watts) mode on. Now, when the  
VCR is standby mode the front display panel will shut off.  
Even the clock disappears. By pressing the VCR STANDBY/ON  
(STANDBY/ON) button again the display panel will reappear.  
TAPE SELECT  
COLOUR SYSTEM  
ECO. MODE  
IPC  
:E180  
:AUTO  
:OFF  
:ON  
6
On completion, press MENU twice to exit the menu.  
œ❷  
END:MENU  
42  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAMSUNG ELECTRONICS (UK) LTD  
AUTHORISED SERVICE CENTERS  
Pro b le m s a n d So lu tio n s  
In the event of warranty service being required, please contact your retailer first. If they cannot provide service, please contact  
your nearest service centre listed below. Service facilities are return to base, however some agents may provide an in-home  
service (there may be a cost for call out). Please refer to your warranty card or retailer for terms and conditions of the warranty.  
GB  
Before contacting the Samsung after-sales service, perform the following simple checks.  
AVON  
ESSEX  
LONDON  
WILLESDEN  
WEST MIDLANDS  
DUDLEY  
BRISTOL  
GOGGLEBOX TV  
TEL: 01275 838083  
WICKFORD  
CENTRAL SERVICE  
TEL: 01268 766333  
ATLANTIC ELECTRIC  
TEL: 0181 451 6155  
J S STOREY ELECTRICAL  
TEL: 01384 455608  
WALSALL  
BEAVER ELECTRONICS  
TEL: 01922 725554  
WARLEY  
MERRIVALE TV SVCS  
TEL: 0121 544 6273/6350  
Problem  
Explanation/Solution  
No power  
Check that the power plug is connected to a wall outlet.  
Have you pressed the VCR STANDBY/ON (STANDBY/ON)  
button?  
MID GLAMORGAN  
BRIDGEND  
BERKSHIRE  
READING  
MANCHESTER  
ASHTON UNDER LYNE  
VIDEOTECH UK  
TEL: 0161 308 4092  
NORTHENDEN  
G H SUMNER LTD  
TEL: 0161 998 2705  
BRIDGEND SERVICE  
TEL: 01656 663463  
A & W SOUND & VISION  
TEL: 01734 872000  
MAIDENHEAD  
J F ASSOCIATES  
TEL: 01628 25709  
WARGRAVE  
GLOUCESTERSHIRE  
You cannot insert a video cassette  
A video cassette can only be inserted with the window  
TEWKESBURY  
SWITCH ELECTRONICS  
TEL: 01684 850063  
WESTON-SUB-EDGE  
PROFESSIONAL ELECTRONIC  
TEL: 01386 841773  
WILTSHIRE  
side up and the safety tab facing you.  
SWINDON  
COLORITE TV LTD  
TEL: 01793 641038  
MERSEYSIDE  
J F ASSOCIATES  
TEL: 01734 401525  
ELLESMERE PORT  
H & H VIDEO & TV  
TEL: 0151 357 1011  
LIVERPOOL  
P & A AUDIO VIDEO LTD  
TEL: 0151 924 7287  
The television programme was not recorded  
Check the VCR aerial connections.  
Is the VCR tuner properly set?  
CAMBRIDGESHIRE  
WORCESTERSHIRE  
DRY DRAYTON  
WORCESTER  
THE HI FI CAR RADIO REPAIR  
TEL: 01905 26623  
HAMPSHIRE  
Check if the safety tab is intact on the cassette.  
DRAYTON ELECTRONICS  
TEL: 01954 211330  
PETERBOROUGH  
DEEPING TV SVCS  
TEL: 01778 343831  
FAREHAM  
SOUND & VISION  
TEL: 01329 286551  
FARNBOROUGH  
ICTV  
TEL: 01252 510118  
PORTSMOUTH  
ICTV  
TEL: 01705 653654  
SOUTHAMPTON  
OLYMPIC TV & AUDIO  
TEL: 01703 703401  
Timer recording was unsuccessful  
Was the VCR STANDBY/ON (STANDBY/ON) button pressed  
to activate the timer?  
MIDDLESEX  
SOUTH YORKSHIRE  
HAYES  
A & A REPAIRS  
TEL: 0181 561 2900/4104  
SHEFFIELD  
GRAPHIC ELECTRONIC SVCS  
TEL: 0114 256 2791  
BARNSLEY  
ALTRA  
TEL: 01226 207434  
Re-check the recording start/stop time settings.  
If there was a power failure or interruption during timer  
recording, the recording will have been cancelled.  
CHESHIRE  
CHESTER  
NORFOLK  
H & H VIDEO & TV  
TEL: 01244 379579  
WARRINGTON  
W L ELECTRONICS  
TEL: 01925 764387  
AYLESHAM  
CORTONS ELECTRICAL  
TEL: 01263 733391  
WATTON  
JULIAN HORN  
TEL: 01953 881440  
No playback picture or the picture  
is distorted  
Check to see if you are using a prerecorded tape.  
NORTH YORKSHIRE  
YORK  
DBS SERVICE CENTRE  
TEL: 01904 789789  
HEREFORD  
HEREFORD  
J P MICRO SVCS  
TEL: 01432 356353  
CORNWALL  
BUDE  
NORTHAMPTONSHIRE  
You cannot see normal broadcasts  
Check the TUNER/EXTERNAL setting. It should be on  
TUNER.  
H B H WOOLACOTTS  
TEL: 01288 352269  
LAUNCESTON  
H B H WOOLACOTTS  
TEL: 01566 772096  
NEWQUAY  
GREENBANK ELECTRONICS  
TEL: 01637 880576  
WADEBRIDGE  
H B H WOOLACOTTS  
TEL: 01208 816155  
KETTERING  
INTEGRATED SVCS  
TEL: 01536 516475  
WEST YORKSHIRE  
BRADFORD  
HERTFORDSHIRE  
GRAPHICK ELECTRON  
TEL: 01274 862267  
HUDDERSFIELD  
GRAPHIC ELECTRONICS  
TEL: 01484 451045  
ILKLEY  
Check the TV/VCR aerial connections.  
BALDOCK  
TECHNICAL REPAIR SVC  
TEL: 01462 491144  
MARKYATE  
TELETECH SVCS  
TEL: 01582 841862  
OXFORDSHIRE  
Noise bars or streaks on playback  
Press the PROG/TRK (  
œ
or  
) / TRK  
(
or  
)
buttons to  
BANBURY  
HITECH  
TEL: 01295 267415  
BOTLEY  
SPECTRUM ELECTRON  
TEL: 01865 250199  
minimize this effect.  
R BEAUMONT  
TEL: 01943 607021  
When the  
during playback, the still picture  
has severe noise barsstreaks  
button is pressed  
A still picture may have noise bars, depending on the condition  
of the tape. Press the PROG/TRK ( or ) /TRK ( or  
buttons during SLOW motion to minimize this effect.  
NORTH HUMBERISDE  
II  
GOOLE  
œ
)
HEADLAND ELECTRCS  
TEL: 01977 661223  
CHANNEL ISLANDS  
SHROPSHIRE  
CUMBRIA  
GUERNSEY  
TELFORD  
W OWEN  
TEL: 01952 613818  
BARROW IN FURNESS  
KENNETH GARDNER  
TEL: 01229 821202  
SEARLE AUDIO  
TEL: 01229 839692  
PENRITH  
TELESKILL LTD  
TEL: 01481 56508  
JERSEY  
ALTERNATIVE ELECT  
TEL: 01534 68277  
ISLE OF WIGHT  
AUDIO VISION SVCS  
TEL: 01983 752023  
SOUTH HUMBERSIDE  
Video Head Cleaning  
If poor pictures appear on a variety of cassettes, the video  
heads may need cleaning. This is not a common problem  
and unless it appears, the heads should not be cleaned.  
When cleaning the video heads, read all instructions  
provided with the head cleaning cassette. Incorrect head  
cleaning can permanently damage the video heads.  
GRIMSBY  
RAYNERS SUPERSTORE  
TEL: 01472 358766  
SOMERSET  
TAUNTON  
ARMTECH ELECTRONICS  
TEL: 01823 279401  
YEOVIL  
M J THOMAS  
TEL: 01935 477255  
KENT  
CANNAN & BROWN  
TEL: 01768 864829  
CANTERBURY  
BARRETTS OF CANTERBURY  
TEL: 01227 766582  
DARTFORD  
BUDGET REPAIR CENTRE  
TEL: 01322 227668  
MAIDSTONE  
DEVON  
NORTHERN IRELAND  
HOLSWORTHY  
CO ARMAGH  
CRAIGAVON TV SVCS  
TEL: 0762 326119/322505  
H B H WOOLACOTTS  
TEL: 01409 253280  
NEWTON ABBOT  
TELLI-SCOPE ELECTRONICS  
TEL: 01626 63907  
PLYMOUTH  
ARGYLE TV & VIDEO  
TEL: 01752 779933  
CTV ELECTRONICS  
TEL: 01752 350950  
STAFFORDSHIRE  
If when tuning in your TV to the VCR test  
pattern your TV does not find the test pattern  
or the pattern when found suffers from  
interference, it may be due to the VCR output  
channel clashing with the normal TV  
transmissions in your area. To prevent this  
you will need to change the VCR output  
channel in the following way  
1. Remove the aerial input plug from the socket marked (aerial  
STOKE ON TRENT  
TELEFAULTS (S.O.T.) LTD  
TEL: 01782 813757  
AVERY ELECTRONICS  
TEL: 01622 682138  
symbol) on the rear of the VCR.  
2. Carry out the instructions Tuning Your Television for the VCR”  
(see page 15).  
3. Carry out the instructions Setting the VCR output Channel”  
(see page 17), move the channel number several channels  
down from the original setting. (example: from 60 to 57).  
4. Replace the aerial plug into the socket marked (aerial symbol)  
on the rear of the VCR.  
EIRE  
CO CORK  
LANCASHIRE  
BLACKPOOL  
SUFFOLK  
TVAE REPAIRS  
TEL: 00353 21 273457  
IPSWICH  
GGN LTD  
TEL: 01473 744300  
KENNETH GARDNER  
TEL: 01253 824047  
LANCASTER  
KENNETH GARDNER  
TEL: 01524 64468  
ROCHDALE  
GRAMPIANS  
FRASERBURGH  
SURREY  
RODGERS ELECTRICAL  
TEL: 01346 518540  
WALLINGTON  
DORSET  
SERVICECARE  
TEL: 0181 669 1145  
HORLEY  
D K AUDIO VISUAL SVCS  
TEL: 01293 786459  
BOURNEMOUTH  
M & G ELECTRONICS  
TEL: 01202 523771  
CTV SERVICES  
TEL: 01706 654983  
HIGHLANDS  
ULLAPOOL  
R & R ELECTRONICS  
TEL: 01854 612608  
5. Re-tune your TV to the VCR again by following instructions  
Tuning Your Television for the VCR(page 15).  
6. If the problem still exists repeat steps 1 to 5 moving several  
more channels away from the original setting.  
LEICESTERSHIRE  
DURHAM  
DURHAM  
LEICESTER  
SOUNT & VISION CENTRE  
TEL: 01162 730444  
EAST SUSSEX  
SEAFORD  
LEE TECH SVCS  
TEL: 0191 371 1300  
DARLINGTON  
GAZE ELECTRONICS  
TEL: 01325 482344  
LOTHIAN  
EDINBURGH  
RETEC AUDIO & VISUAL  
TEL: 0131 478 7779  
CLEARVIEW RENTAL & RELAY  
TEL: 01323 898989  
EASTBOURNE  
STARTEC SVCS  
TEL: 01323 412012  
LINCOLNSHIRE  
BRANSTON  
STUART WALLACE  
TEL: 01522 791496  
If you are unable to solve the problem after reading the above instructions, note:  
The model and serial number on the rear of your VCR  
The warranty information  
STRATHCLYDE  
DYFED  
ESSEX  
GLASGOW  
DSC ELECTRONICS  
TEL: 0141 941 3711  
CARMARTHEN  
LONDON  
TYNE & WEAR  
ADVANCE CONSUMER  
TEL: 01267 236143  
ST CLEARS  
BEN EVANS & SON  
TEL: 01994 231015  
HIGH HOLBORN  
NEWCASTLE UPON  
TYNE  
M SINGH RADIO & TV  
TEL: 0191 226 0446  
BERRYS OF HOLBORN  
TEL: 0171 405 1157  
TAYSIDE  
DUNDEE  
ANCRUM ELECTRONICS  
TEL: 01382 454511  
A clear description of the problem  
LONDON  
ARMSTRONG SERVICES  
TEL: 0181 523 0023/0051  
WEST EALING  
WEST MIDLANDS  
Then contact your nearest SAMSUNG after-sales service.  
COVENTRY  
D & J HENRY  
TEL: 01203 431393  
BRAINTREE  
GWYNNE TV & ELECTRICAL  
TEL: 01376 322567  
BABBER ELECTRONICS  
TEL: 0181 579 6315  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAMSUNG EUROPEAN BLOC WARRANTY  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Radio Shack Clock Radio 63 994 User Guide
RCA CRT Television E13701 User Guide
Roland Recording Equipment SCWS04 User Guide
Rotel Stereo Receiver RCD 971 User Guide
Russell Hobbs Oven 550 004 User Guide
Ryobi Router RT501W User Guide
Samsung Automobile UN40D6000 User Guide
Samsung DVD Player DVD S428K User Guide
Samsung Washer DC68 02347B FR User Guide
Sarlo Trimmer CS 16 User Guide