HW-D7000
Blu-ray™
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed
below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachment/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3
Safety Information
Precautions
•
•
•
Ensure that the AC power supply in your house complies with specifications listed on the identification sticker
located on the back of your product.
Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm / 20~25 inches).
Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
Do not stack anything on top of the product.
Before moving the product, ensure the Disc Insert Hole is empty.
To disconnect the product completely from the power supply, remove its plug from the wall outlet.
- If you leave the product unused for a long period of time, disconnect the plug from the wall outlet.
During thunderstorms, disconnect the AC plug from the wall outlet. Voltage spikes caused by lightning could
damage the product.
Do not expose the product to direct sunlight or other heat sources. This could cause the product to overheat
and malfunction.
•
•
•
•
•
•
Protect the product from moisture, excess heat, and equipment creating strong magnetic or electric fields (i.e.
speakers.).
•
•
•
Disconnect the power cable from the AC supply if the product malfunctions.
Your product is not intended for industrial use. It is for personal use only.
Condensation may occur if you store your product or a disc in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the product has reached room temperature before using.
The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
•
Viewing TV using the 3D function
IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and
understand the following safety information before using the TV’s 3D function.
WARNING
•
•
•
•
•
Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea and headaches. If you
experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.
Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D
TV, remove your 3D Active Glasses, and rest.
A responsible adult should frequently check on children who are using the 3D function. If there are any reports of
tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.
Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective
goggles, etc.)
Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D
Active Glasses while moving around may result in injuries caused by running into objects, tripping, and/or falling.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
English
Cautions on Handling and Storing Discs
License
Small scratches on the disc may reduce sound
and picture quality or cause skipping.
Be especially careful not to scratch discs when
handling them.
•
•
Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories.
"Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide patents
issued & pending. DTS and the Symbol are registered
trademarks, & DTS-HD, DTS-HD Master Audio | Essential and
the DTS logos are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved."
Holding discs
•
•
Do not touch the playback side of the disc.
Hold the disc by the edges so that
fingerprints will not get on the
surface.
•
"ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX, Inc. This is an official DivX
information and software tools to convert your files into DivX video.
•
Do not stick paper or tape on the disc.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate the DivX VOD section in
your device setup menu. Go to vod.divx.com for more information on
how to complete your registration.
Disc Storage
•
•
•
Do not keep in direct sunlight
Keep in a cool ventilated area
Keep in a clean protection jacket and store
vertically.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
Inc. and are used under license."
✎
NOTE
Do not allow the discs to become contaminated with
dirt.
Covered by one or more of the following U.S. patents : 7,295,673;
7,460,668; 7,515,710; 7,519,274
Do not load cracked or scratched discs.
•
HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
•
•
Oracle and Java are registered trademarks of Oracle and/or its
affiliates. Other names may be trademarks of their respective owners.
•
When cleaning, wipe gently from the inside to
the outside of the disc
This item incorporates copy protection technology that is protected by
U.S. patents and other intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
✎
NOTE
Condensation may form if warm air comes into
contact with cold parts inside the product. When
condensation forms inside the product, it may not
operate correctly. If this occurs, remove the disc
and let the product stand for 1 or 2 hours with the
power on.
•
•
Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray
Disc Association.
iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries. iPhone is a trademark of
Apple Inc.
•
< Open Source License Notice >
In the case of using open source software, Open Source
Licenses are available on the product menu.
Copyright
© 2011 Samsung Electronics Co., Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5
Contents
2
3
4
5
5
5
Safety Warnings
SAFETY INFORMATION
Important Safety Instructions
Precautions
Cautions on Handling and Storing Discs
License
Copyright
2
GETTING STARTED
8
8
Key features of your new Blu-ray Receiver
10 Icons that will be used in manual
11 Disc Types and Characteristics
15 Accessories
16 Description
16
18
Front Panel
Rear Panel
19 Remote Control
21 Speaker Positioning
CONNECTIONS
22 Attaching the Toroidal Ferrite Core to the Power Cord of
the Main Unit
23 Connecting the Speakers
24 Connecting the Bi-AMP Speaker
21
25
26
Connecting External Devices/your TV via HDMI
Connecting to your TV
27 Connecting a Cable, Satellite or Set-top Box
28 Connecting a Game Console
29 Connecting a CD Player
30 Video Conversion Flow According to the Connected Port
31 Connecting the FM Antenna
31 Connecting AUX Components
32 Connecting to a Network
34 Initial Settings
SETUP
35 Accessing the Settings Menu
36 Display
36
37
37
37
37
39
39
39
39
39
39
3D Settings
TV Aspect (Picture Size and Format)
Smart Hub Screen Size
BD Wise (Samsung Products only)
Resolution
34
HDMI Color Format
Movie Frame (24 Fs)
HDMI Deep Color
Still Mode
Progressive Mode
Video Conversion
40 Audio
40
42
43
44
44
44
45
45
45
45
47
47
47
Speaker Settings
Musical Room Calibration
Surround
Crossover Frequency
MP3 Enhancer
Smart Volume
Dual Mono
HDMI Audio
Audio Return Channel
Digital Output
Dynamic Range Control
HDMI Auto Sync
Audio Sync
Download from Www.Somanuals.com. All Manuals Search And Download.
6
English
47 Network
SETUP
47
50
50
Network Settings
Network Status
BD-LIVE Internet Connection
51 System
47
51
51
51
51
51
52
52
Initial Settings
Anynet+ (HDMI-CEC)
BD Data Management
Input Selection
Time Zone
DivX® Video On Demand
Reset
52 Language
52 Security
52
52
52
BD Parental Rating
DVD Parental Rating
Change Password
52 General
52
53
Front Display
Network Remote Control
53 Support
53
55
Software Upgrade
Contact Samsung
56 Playing a Disc
56 Using the Disc menu / Title menu / Popup menu
57 Playing the Title List
BASIC FUNCTIONS
57 Using the Search and Skip Functions
58 Slow Motion Play/Step Motion Play
58 Repeat Playback
56
59 Using the TOOLS button
61 Listening to Music
63 Sound Mode
65 Playing back a Picture
66 Playing back a USB Storage Device
67 Listening to Radio
68 Connecting an iPod/iPhone Using the USB Cable
68 Connecting an iPod/iPhone Using the Dock
69 iPod/iPhone Models You Can Use with This Product
70 Using Smart Hub
77 Samsung Apps
NETWORK SERVICES
79 Using vTuner Function
79 BD-LIVE™
79 Using the AllShare Function
70
80 Troubleshooting
84 Specifications
OTHER INFORMATION
80
•
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7
Getting Started
Key features of your new Blu-ray Receiver
Product Features
Digital Receiver
This product is a pure digital receiver that performs digital signal processing to minimize signal distortion
and loss.
3D
This product can play 3D contents through an HDMI cable.
To implement the 3D effect, connect a 3D TV to the product using an HDMI cable, and play the 3D
content while wearing 3D vision glasses.
Smart Hub
You can download various for pay or free-of charge applications through a network connection. These
applications provide a range of Internet services and content including news, weather forecasts, stock
market quotes, games, movies, and music.
AllShare
You can play videos, music and photos saved on your devices (such as your PC, mobile phones or
NAS) through the home theater via a network connection.
Audio Sync function
If you have connected the product to a digital TV, video can sometimes lag behind the audio.
To compensate for this, you can adjust the audio delay time so that the audio syncs with the video.
iPod SYNC function
If the video signal from an iPod player you attached to the product lags behind the audio signal during
playback, you can set the audio delay time so that the video and audio match.
iPod & iPhone support
If you have connected an iPod player to the home theater using the iPod/iPhone specific USB cable, you
can play the music files in the iPod/iPhone through the connected speakers.
BD Wise
BD Wise automatically adjusts BD Wise-compliant Samsung products to their optimal settings.
This feature is enabled only if BD Wise-compliant Samsung products are connected to each other using
an HDMI cable.
3D SOUND
You can enjoy more natural and vivid surround sound with enriched tones.
ARC (Audio Return Channel)
You can enjoy TV sound from the Home Theater speakers by using just one HDMI cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
English
DOLBY DIGITAL EX
Adds a surround back channel for more spacious sound compared to regular 5.1 channel Dolby Digital.
Dolby Pro Logic llx
Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channels out of 2 channel or multi
channel sources.It also provides Music,Movie and Game modes.
Dolby Pro Logic IIx is an improved surround system that is optimized to a 7.1 CH multimedia system,
enabling you to maximize your entertainment experience.
Dolby Pro Logic llz
Dolby Pro Logic IIz adds front height channels to surround sound, creating a 7.1 playback system for
video games, home music, and movies; bringing enhanced spatial effects and enveloping sound.
Dolby Digital Plus
Dolby Digital Plus is the next-generation audio technology for all high-definition programming and media.
Dolby True-HD
Dolby True-HD is Dolby’s next-generation lossless technology developed for high-definition disc-based
media.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for both music and movie contents and uses less
compression than Dolby Digital for richer sound.
DTS Neo 6
Provides a full range of 6 channels by converting a digital PCM or analog stereo signal using DTS digital
matrix decoding.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to 24 bit/96kHz and applies it to a 5.1 CH sound
track.
DTS-ES (Extended Surround) Direct 6.1
The DTS-ES (Extended Surround) system is a new multi digital signal format that was developed by Digital
Theater Systems Inc.
Supporting full compatibility with the conventional DTS digital surround sound format, the DTS-ES
(Extended Surround) system improves the surround signal for a 360-degree surround effect.
DTS-ES adds an additional rear center surround channel for 6.1 channel sound.
DTS-HD MA (Digital Theater Systems - Master Audio, High Resolution)
DTS-HD Audio provides the highest quality multi-channel sound possible.
It delivers sound quality that matches the clear and vivid images of high-definition video.
SFE (Sound Field Effect) Using 32bit Audio Digital Signal Processing
Provides more realistic surround sound with normal stereo audio sources.
✎NOTE
Write as "VFD" when it is BD/DVD mode :
- DTS ES Discrete : Write as "DTS ES"
-DTS ES Matrix, normal DTS : Write as "DTS"
Download from Www.Somanuals.com. All Manuals Search And Download.
English
9
Getting Started
Icons that will be used in manual
Make sure you understand the following terms before reading the rest of the user manual.
Term
Logo
Icon
Definition
BD-ROM
Indicates a function available on a BD-ROM.
h
z
Z
Indicates a function available on a BD-RE/-R disc recorded in the
BD-RE/-R
BD-RE format.
DVD-VIDEO
Indicates a function available on a DVD-VIDEO.
DVD-RW(V)
DVD-R
Indicates a function available on recorded DVD+RW or DVD-RW(V)/DVD-
R/+R discs that have been recorded and finalized.
DVD+RW
y
DVD+R
Audio CD
Indicates a function available on an audio CD-RW/-R (CD-DA format).
o
w
G
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
MP3
WMA
-
-
storage media containing MP3 or WMA contents.
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
storage media containing JPEG contents.
JPEG
DivX
MKV
MP4
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
x
storage media containing DivX contents.
DivX
-
USB storage
device
Indicates a function available on a USB storage device.
F
!
Indicates a situation where a function does not operate or settings may be
CAUTION
NOTE
-
-
-
cancelled.
Indicates tips or instructions that can help you operate a function better.
Indicates that you can access this function quickly and easily by
pressing a button on the remote control.
✎
Shortcut Key
•
•
This product is compatible with the NTSC color system only.
PAL discs will not play.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
English
Logos of Discs that can be played
Disc Types and Characteristics
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc
compatibility issues are possible. Not all discs are
compatible and not every disc will play back. For
additional information, refer to the Disc Types and
Characteristics section of this Manual.
Blu-ray Disc
3D Blu-ray Disc
✎NOTE
Playback may not work for some types of discs or
when you use specific functions such as angle
change and aspect ratio adjustment. Information
about the discs is written in detail on the box.
Please refer to this if necessary.
NTSC broadcast system in
U.S.A, Canada, Korea,
Japan
Dolby Digital Plus
Do not allow discs to become dirty or scratched.
Fingerprints, dirt, dust, scratches, or deposits of
cigarette smoke on the recording surface may
make it impossible to playback a disc.
When you play a BD-Java title, loading may take
longer than a normal title or some functions may
perform slowly.
DTS-HD High Resolution
Audio
Dolby TrueHD
Discs that cannot be played
•
•
•
•
•
•
HD DVD Disc
DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
Super Audio CD(except CD layer)
DTS-HD Master Audio |
Essential
Java
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD
•
CDGs play audio only, not graphics.
✎NOTE
Some commercial discs and DVD discs purchased
outside your region may not play on this product.
If a DVD-R/-RW disc has not been recorded properly
in DVD video format, it will not play on this product.
BD-LIVE
DTS 96/24
DTS-ES
DTS Neo 6
Download from Www.Somanuals.com. All Manuals Search And Download.
English
11
Getting Started
Region Code
BD-RE/-R
Blu-ray RE/-R discs can be recorded and played
back. This product can play back a BD-RE/-R disc
recorded by other compatible Blu-ray disc
recorders.
Both the product and the discs are coded by
region. These regional codes must match for the
product to play the disc.If the codes do not
match, the disc will not play.
DVD-VIDEO
Region
•
This product can play back pre-recorded commercial
DVD discs (DVD-VIDEO discs) with movies.
Disc Type
Blu-ray
Area
Code
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
•
When switching from the first layer to the second
layer of a dual-layered DVD-VIDEO disc, there
may be momentary distortion in the image and
A
East Asia.
sound. This is not a malfunction of the product
.
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
DVD-RW/-R/+R
B
C
1
2
3
4
5
6
This product can play back a DVD-RW/-R/+R disc
recorded and finalized with a DVD video recorder.
The ability to play back may depend on recording
conditions.
India, China, Russia, Central and
South Asia.
DVD+RW
The U.S., U.S. territories and
Canada
•
This product can play back a DVD+RW disc
recorded with a DVD Video recorder. The ability to
play back may depend on recording conditions.
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
Audio CD (CD-DA)
•
This product can play back CD-DA format audio
CD-RW/-R discs.
The product may not be able to play some CD-
RW/-R discs due to the condition of the
recording.
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
•
DVD-VIDEO
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
CD-RW/-R
•
Use 700MB (80 minute) CD-RW/-R discs. Do not
use 800MB (90 minute) or larger discs, as these
discs may not play back.
If the CD-RW/-R disc was not recorded as a
closed session, you may experience delays when
playing back the beginning of the disc or all
recorded files may not play.
Some CD-RW/-R discs may not play on this
product, depending on the device which was
used to burn them. For contents recorded on CD-
RW/-R media from CDs for your personal use,
playability may vary depending on the contents
and discs.
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
•
China
•
Disc Types
BD-ROM
Blu-ray discs can only be played back.
This product can play back pre-recorded
commercial BD-ROM discs.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
English
Disc Format
Using JPEG discs
•
•
•
The home theater can play back D-R/-RW, DVD-RW/-R discs recorded in the UDF or JOLIET format.
Only JPEG files with the ".jpg", ".JPG", ".jpeg" or "JPEG" extension can be displayed.
Progressive JPEG is supported.
DVD-RW/-R (V)
•
This format is used for recording data on DVD-RW or DVD-R discs. This product can play DVD-RW or DVD-R
discs if they have been finalized.
•
If a disc that has been recorded in Video Mode by a different maker’s recorder but has not been finalized, it
cannot be played by this product.
Supported File Formats
Video File Support
File Extension
Container
Video Codec
DivX 3.11/4.x/5.1/6.0
XviD
Audio Codec
Resolution
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
MP3
AC3
LPCM
ADPCM
DTS Core
*.avi
AVI
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
MP3
AC3
LPCM
ADPCM
DTS Core
*.mkv
*.asf
MKV
ASF
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
MP3
AC3
LPCM
ADPCM
WMA
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
*.wmv
*.mp4
WMA
ASF
Window Media Video v9
H.264 BP/MP/HP
MPEG4 SP/ASP
XVID
MP3
ADPCM
AAC
MP4
ADPCM
AAC
HE-AAC
1920x1080
1920x1080
H.264 BP/MP/HP
MPEG4 SP/ASP
*.3gp
3GPP
Download from Www.Somanuals.com. All Manuals Search And Download.
English
13
Getting Started
File Extension
Container
Video Codec
Audio Codec
Resolution
AC3
1920x1080
MPEG2
VRO
*.vro
MPEG
LPCM
VOB
352x288
MPEG1
AC3
MPEG
LPCM
AAC
352x288
MPEG1
MPEG2
*.mpg
*.mpeg
1920x1080
PS
TS
1920x1080
H.264
AC3
AAC
MP3
DD+
HE-AAC
1920x1080
1920x1080
MPEG2
H.264
*.ts
*.tp
*.trp
1920x1080
VC1
Restrictions
•
•
•
•
•
Some of the Codecs listed above will not play if there is a problem with the contents.
Corrupt video sources or sources with incorrect container information will not play properly.
AV sources that exceed the standard bit rate or frame rate may not play properly.
If the index table is corrupt, the Seek (Jump) function will not be supported.
If you play a video via the network, it may not play properly depending on the network status.
Video decoder
•
•
•
Up to H.264 Level 4.1 supported.
H.264 FMO/ASO/RS, VC1 SP/MP/AP L4, AVCHD not supported.
XVID, MPEG4 SP, ASP :
- Below 1280 x 720: 60 frame max
- Above 1280 x 720: 30 frame max
•
GMC 2 or higher not supported.
Audio decoder
•
•
•
•
Up to WMA 7,8,9 supported.
WMA 9 PRO with more than two channels (multi-channel) not supported.
WMA 9 Lossless, Voice not supported.
WMA sampling rate at 22050Hz mono not supported.
Music File Support
File Extension
Container
Audio Codec
Support Range
*.mp3
MP3
-
MP3
Compliant with WMA version 10
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
*.wma
WMA
WMA
* Bit rates - All bit-rates in the range 5kbps to
384kbps
Download from Www.Somanuals.com. All Manuals Search And Download.
14
English
6) Connect USB devices directly to the
product's USB port. Connecting through a
USB cable may cause compatibility
problems.
Notes on the USB connection
Supported devices:
7) Inserting more than one memory device into
a multi-card reader may cause the reader to
operate improperly.
USB storage media, MP3 player, digital camera,
USB card reader
1) The product does not support folder or file
names longer than 125 characters.
8) The product does not support the PTP
protocol for digital cameras
2) A subtitle file bigger than 300 KB may not be
9) Do not disconnect a USB device during a
"loading" process.
properly displayed.
3) Some USB/digital camera devices may not
be compatible with the product.
10) The bigger the image resolution, the longer
the image takes to display.
4) The praoduct supports the FAT16 and FAT32
11) This player cannot play MP3 files with DRM
(Digital Rights Management) downloaded
from commercial sites.
file systems.
5) Photo (JPEG), music (MP3,) and video files
must have Korean or English file names.
Otherwise, the files will not play.
Accessories
Check the box for the supplied accessories listed below.
INPUT SELECT
TV SOURCE
POWER
BD-RX
TV
SHIFT
1
2
3
4
5
6
SLEEP
TONE
7
8
9
S.DIRECT
AUDIO ASSIGN
FULL
SCREEN
0
REPEAT
MUTE
TUNING
/CH
VOL
DISC MENU
TOOLS
SFE MODE
MENU
(For Power cord)
TITLE MENU
POPUP
INFO
RETURN
EXIT
TUNER
MEMOR
i
P
o
d
S
Y
N
C
Y
MO/ST
A
B
C
D
SMART
SEARCH
vTuner
2D
→
3D
HUB
3
D
S
O
U
N
D
NEO:6
NETFLIX
Remote Control
(AH59-02377A)/
Batteries (AAA size)
(4301-000116)
Video Cable
(AH39-40001V)
FM Antenna
(AH42-00017A)
Toroidal Ferrite Core
(3301-000144)
User's Manual
(AH68-02334S)
iPod Dock
(AH96-00051B)
ASC Microphone
(AH30-00099A)
Download from Www.Somanuals.com. All Manuals Search And Download.
English
15
Getting Started
Description
Front Panel
1
2
3
4
5
10
6
7
8
9
INPUT SELECT
MASTER VOLUME
ASC MIC
VIDEO
AUDIO
PHONES
SELECT
TONE
CONTROL
TUNING
MODE
AUDIO
ASSIGN
AUDIO
EFFECT
Smart HUB
S.Direct
vTuner
AV SYNC
MEMORY
MENU
RETURN
3D SOUND
AUX
1
IN
11 12 13 14 15 16
17
18 19
20
21 22 23 24
25 26
27
28
Used to select a source.
BD/DVD ꢀ SAT ꢀ GAME ꢀ AUX1 ꢀ AUX2 ꢀ CD ꢀ R-IPOD ꢀ FM ꢀ TV
INPUT SELECT
1
REMOTE CONTROL SENSOR Detects signals from the remote control.
2
3
4
5
6
DISC SLOT
Insert disc here.
STOP BUTTON
PLAY/PAUSE BUTTON
ENTER BUTTON
Stops disc playback.
Plays a disc or pauses playback.
Selects menu items.
OPEN/CLOSE BUTTON
DISPLAY
Ejects a Disc.
7
8
9
Displays the playing/audio input status, time, listening mode, etc.
Adjusts the volume level.
MASTER VOLUME
Turns the product on and off.
10
POWER BUTTON (
)
Download from Www.Somanuals.com. All Manuals Search And Download.
16
English
TONE CONTROL BUTTON
SMART HUB BUTTON
Used to set the bass, treble level and tone to on/off.
Display the Smart Hub service screen.
11
12
Used to select the S.DIRECT mode.
S.DIRECT BUTTON
(Output the original signal as it is without applying the sound field effect or any
other sound effect.
13
vTuner BUTTON
Used to select the vTuner.
14
15
16
AV SYNC BUTTON
TUNING MODE BUTTON
Used to set the Audio Delay.
Used to select the Manual or Preset mode for FM radio.
SELECT BUTTON
MEMORY BUTTON
MENU BUTTON
Used to change the radio frequency.
Used to set a preset radio frequency.
Display the home menu screen.
17
18
19
UP(,), DOWN(.), LEFT(<),
RIGHT(>) BUTTONS
Used to move the cursor up, down, left or right.
20
RETURN BUTTON
AUDIO ASSIGN BUTTON
AUDIO EFFECT BUTTON
3D SOUND BUTTON
ASC MIC JACK
Return to the previous menu.
21
22
23
24
25
Toggles to select an input mode for the selected source.
Toggles to select a surround sound mode.
Used to set the 3D sound.
Used to connect the ASC Microphone for setting up MRC (Musical Room Calibration).
You can connect a USB memory flash stick here and use it as storage when the product is
connected to BD-LIVE. You can also use the USB Host for software upgrades and MP3/
JPEG/DivX/MKV/MP4 playback.
USB PORT
26
Auxiliary AV input terminals used to connect a camcorder, portable DVD player
or gaming device.
AUX 1 IN JACKS
PHONES JACK
27
28
Used to connect a set of headphones or earphones.
✎NOTE
You must use a USB memory flash stick to perform a software upgrade using the USB Host jack.
When the product displays the Blu-ray disc menu, you cannot start the movie by pressing the PLAY button on the
product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the
ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
17
Getting Started
Rear Panel
1
2
3
4
5
6
HDMI OUT
HDMI IN
LAN
iPod
ARC
(MONITOR)
HDMI
1
HDMI
2
HDMI
3
HDMI 4
(AUX2)
(SAT)
(GAME)
(AUX1)
SPEAKER IMPEDANCE
SURROUND BACK
:
4~8
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
1
2
SAT
GAME
TV
MONITOR
/FRONT HEIGHT
CENTER
(SAT)
(GAME)
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
GAME
TV
CD
OPTICAL
(SAT)
1
OPTICAL
(GAME)
2
OPTICAL
(TV)
3
COAXIAL
(CD)
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
7
8
9
10
11
12 13
14
VIDEO IN JACKS
Receives the video signal from a video player (SAT, GAME, TV).
Outputs the video signal to video devices (TV, Projector etc).
1
2
3
4
5
VIDEO OUT JACK
LAN TERMINAL
iPod JACK
Can be used for network based services (see pages 70~79),
BD-LIVE and software upgrade under the network connection.
Connect the iPod dock connector here.
Outputs digital video and audio signals simultaneously using an
HDMI cable.
HDMI OUT JACK
Receives digital video and audio signals simultaneously using an
HDMI cable.
HDMI IN JACKS
6
7
FM ANTENNA JACK
AUDIO IN JACKS
Connect the FM antenna.
Receives the audio signal from a video player (SAT, GAME, TV, CD).
Receives the component video signal.
Outputs the component video signal.
Receives the digital optical audio signal.
Receives the digital coaxial audio signal.
Connect the subwoofers.
8
COMPONENT VIDEO IN JACKS
COMPONENT VIDEO OUT JACKS
9
10
11
12
13
OPTICAL IN JACKS (DIGITAL AUDIO IN)
COAXIAL IN JACK (DIGITAL AUDIO IN)
SUBWOOFER AUDIO OUT JACKS
The front speaker and surround back speaker ports can be
connected to a speaker that supports bi-amplifying. For connecting
to the bi-amplifier, refer to page 24.
SPEAKER OUT TERMINALS
14
Download from Www.Somanuals.com. All Manuals Search And Download.
18
English
Remote Control
Tour of the Remote Control
Press to select Blu-ray's mode.
or
INPUT SELECT
TV SOURCE
POWER
Press to select TV's video mode.
Turn the product on and off.
To eject the disc.
To change to TV mode, press the
TV button.
BD-RX
1
TV
SHIFT
To change to receiver, press the
To use second function of some
button.
After pressing the SHIFT button,
Set a Sleep time to shut off the
product.
BD-RX button.
2
3
Press numeric buttons to operate options.
4
5
6
You can adjust the bass and
SLEEP
TONE
treble level.
After pressing the SHIFT button,
7
8
9
Toggles to select an input mode for
the selected source.
S.DIRECT
AUDIO ASSIGN
Press to select S.DIRECT mode.
FULL
SCREEN
Allows you to repeat a title, chapter,
track or disc.
REPEAT
0
or
Press to see the full screen on a TV.
Press to search backwards or
Press to skip backwards or forwards.
forwards.
Press to stop/play a disc.
Press to pause a disc.
Cut off the sound temporarily.
MUTE
Search for active FM stations and
change channels.
Adjust the volume.
TUNING
/CH
VOL
DISC MENU
TOOLS
SFE MODE
MENU
You can set the SFE (Sound Field
Effect) mode best suited for the
type of music you are listening to.
Press to move to the home menu.
Press to view the disc menu.
TITLE MENU
POPUP
Use to enter the popup menu/title
menu.
INFO
Use to display the playback
information when playing
a Blu-ray/DVD disc.
Press to use the Tools menu.
Select on-screen menu items and
change menu value.
Press to exit the menu.
RETURN
EXIT
Return to the previous menu.
Correct the audio synchronization
TUNER
Used to set a preset radio frequency.
iPod SYNC
MO/ST
MEMORY
when playing iPod video content.
A
B
C
D
Select MONO or STEREO for radio
broadcasting.
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
vTuner
2D → 3D
SMART
SEARCH
HUB
Press to enjoy an ordinary 2D video
in 3D mode.
3D SOUND
NEO:6
Press to use Smart Hub.
NETFLIX
Press to use Netflix.
Select the desired Dolby Pro
Logic II audio mode.
Press to search contents.
Press this to use the vTuner.
Select the desired NEO:6 mode.
Press to apply 3D Sound effect.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
19
Getting Started
Installing batteries in the Remote Control TV Brand Code List
* Battery size: AAA
Brand
Code
56, 57, 58
01, 15
01, 02, 03, 04, 05,
06, 07, 08, 09, 10,
11, 12, 13, 14
Brand
Code
Admiral
Mitsubishi/
18, 40, 59, 60, 75
(M.Wards)
MGA
A Mark
Anam
AOC
MTC
NEC
18
18, 19, 20, 40, 59, 60
Nikei
03
03
03
Onking
Onwa
01, 18, 40, 48
Bell &
Howell
06, 07, 08, 09, 54,
66, 67, 73, 74
Panasonic
Penney
Philco
57, 58, 81
(M.Wards)
18
Brocsonic
Candle
59, 60
18
03
03, 18, 25
97
03
18
✎NOTE
03, 15, 17, 18, 48,
54, 59, 62, 69, 90
Make sure to match the “+” and “–” ends of
Cetronic
Citizen
15, 17, 18, 40,
48, 54, 62, 72
63, 66, 80, 91
15, 18, 59
40
06, 66, 67
17, 48, 56, 60,
61, 75
Philips
the batteries with the diagram inside the
compartment.
Pioneer
Portland
Proton
Cinema
Classic
Concerto
Contec
Coronado
Craig
Assuming typical TV usage, the batteries last
for about one year.
The remote control can be used up to
approximately 23 feet (7 meters) in a straight line.
Quasar
46
15
Radio
Shack
03, 05, 61, 82, 83, 84
RCA/
Proscan
18, 59, 67, 76, 77,
78, 92, 93, 94
Croslex
Crown
62
03
Setting the Remote Control
Realistic
Sampo
03, 19
40
Curtis
Mates
59, 61, 63
You can control certain functions of your TV with
this remote control.
When operating a TV with the remote control
00, 15, 16, 17, 40,
43, 46, 47, 48, 49,
59, 60, 98
CXC
03
Samsung
02, 03, 04, 15, 16,
17, 18, 19, 20, 21,
22, 23, 24, 25, 26,
27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
Sanyo
Scott
Sears
Sharp
19, 61, 65
03, 40, 60, 61
15, 18, 19
Daewoo
1. Press the TV button to set the remote control
to TV mode.
2. Turn on your TV.
Daytron
Dynasty
40
03
15, 57, 64
Signature
2000
03, 15, 40, 46, 59, 61,
57, 58
Emerson
64, 82, 83, 84, 85
(M.Wards)
3. While holding down the POWER button, enter
Fisher
Funai
19, 65
03
03
Sony
Soundesign
Spectricon
SSS
50, 51, 52, 53, 55
the code corresponding to your brand of TV.
03, 40
01
18
•
If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
Futuretech
General
06, 40, 56, 59,
66, 67, 68
40
15, 18, 50, 59, 69
45
56, 59, 67, 86
70
59, 61, 87, 88
03, 15, 40
15
Electric (GE)
18, 40, 48, 54,
59, 60, 62
Hall Mark
Hitachi
Inkel
Sylvania
•
Example : For a Samsung TV
Symphonic
Tatung
Techwood
Teknika
TMK
61, 95, 96
06
18
03, 15, 18, 25
18, 40
19, 57, 63, 71
18
While holding down the POWER button, use the
number buttons to enter 00. If that does not
work, try 15, then 16, etc.
JC Penny
JVC
KTV
4. If the TV turns off, the setting is complete.
KEC
Toshiba
Vidtech
Videch
•
You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
KMC
LG
01, 15, 16, 17, 37, 38,
59, 60, 69
(Goldstar)
39, 40, 41, 42, 43, 44
15, 17, 18, 40,
48, 54, 60, 64
✎NOTE
Luxman
18
Wards
LXI
(Sears)
19, 54, 56, 59,
The remote control may not work on some
Yamaha
York
18
40
03
58, 79
01
03, 54
60, 62, 63, 65, 71
brands of TV's. Also, some operations may not
be possible, depending on your brand of TV.
The remote control will work with Samsung TVs
by default.
15, 17, 18, 48, 54,
Magnavox
59, 60, 62, 72, 89
Yupiteru
Zenith
Marantz
Matsui
MGA
40, 54
54
18, 40
Zonda
Dongyang
Download from Www.Somanuals.com. All Manuals Search And Download.
20
English
Connections
This section involves various methods of connecting the receiver to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Speaker Positioning
There are two methods for positioning the speakers.
FHL
FHR
6.6~9.8 feet (2~3m)
6.6~9.8 feet (2~3m)
RECEIVER
RECEIVER
SL
SR
SL
SR
SBL
SBR
L, R, C, SW, SL, SR, SBL, SBR ( Dolby Pro Logic IIx )
L, R, C, SW, SL, SR, FHL, FHR( Dolby Pro Logic IIz)
Position of Receiver
Place the Receiver on a dedicated stand or rack.
Subwoofer
g
The position of the subwoofer is not so critical. Place it anywhere you like.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the center speaker or place them slightly in
front of the center speaker.
Center Speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects and
sound will not come from them all the time.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
21
Connections
Surround Back Speakers
SBL SBR
If you are using two surround center speakers, place them behind the listening position.
Place the surround back speaker about 2.3-3.3 feet (70 cm to 1 m).
FHL FHR
Front Height Speakers
(Using Dolby Pro Logic IIz)
When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR position above the
front L and front R speakers at least 3.3 feet(1 m) above each one.
Speaker Configuration
For the best surround-sound experience, you should connect seven speakers and a powered
subwoofer. The following table shows which channels you should use based on the number of
speakers you have.
7 speakers
(DPL IIx)
7 speakers
(DPL IIz)
2 speakers
3
speakers 4 speakers
5 speakers
6 speakers
SBL
SBL
SBR
FHL
FHR
✎ NOTE
No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
If you place a speaker near your TV set, screen color may be distorted because of the magnetic field
generated by the speaker. If this occurs, place the speaker away from your TV set.
Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit
If you attach a Toroidal ferrite core to the power cord, it will help to prevent RF interference from
radio signals.
1. Pull the fixing tab of the Totoidal ferrite core to
LAN
iPod
HDMI OUT
HDMI IN
ARC
(MONITOR)
HDMI
1
HDMI
2
HDMI
3
HDMI 4
(AUX2)
(SAT)
(GAME)
(AUX1)
open it.
SPEAKER IMPEDANCE 4~8
:
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
2. Make a loop in the power cord.
SURROUND BACK
/FRONT HEIGHT
SURROUND BACK
/FRONT HEIGHT
1
2
FRONT
SURROUND
SURROUND
FRONT
SAT
GAME
TV
MONITOR
CENTER
(SAT)
(GAME)
Y
SUBWOOFER
OUT
PB/CB
PR/CR
3. Attach the Toroidal ferrite core to the power cord as
SAT
GAME
TV
CD
OPTICAL
(SAT)
1
OPTICAL
(GAME)
2
OPTICAL
(TV)
3
COAXIAL
(CD)
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
the figure shows and press it until it clicks.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
English
Connecting the Speakers
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
FRONT (R) SURROUND (R)
SURROUND BACK (R)
SURROUND BACK (L) SURROUND (L)
FRONT (L)
ACTIVE SUBWOOFER
SURROUND BACK
/FRONT HEIGHT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
CENTER
SUBWOOFER
OUT
SPEAKERS OUT
HDMI OUT
MDMI IN
LAN
iPod
CENTER
SPEAKER IMPEDANCE
:
4~8
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
AUDIO IN
IN
OUT
FM ANT
✎NOTE
Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or
objects into the duct (hole).
Never touch speaker terminals while the power is on. Doing so could result in electric shock.
Make sure the polarities (+ and -) are correct.
If you want to use two active subwoofer speakers, connect both subwoofer speakers into the
SUBWOOFER OUT terminals in the rear panel.
We recommend more than 120W of permited input and connection with speaker that more than
4ohm impedance.
If you use lower level products than our recommend, it can be cause of Speaker Unit or Amplifer's
trouble so be cations about it.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
23
Connections
Connecting the Bi-AMP Speaker
Connect the tweeter (high range) port and woofer (low range) to the front port and surround back speaker
port respectively as appropriate. Then, you can use the bi-amplifi cation feature that supports enriched high
range and base tones.
Bi-AMP Speaker R
Bi-AMP Speaker L
SURROUND BACK
/FRONT HEIGHT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
CENTER
Tweeter
Tweeter
Woofer
Woofer
SPEAKERS OUT
LAN
iPod
HDMI OUT
HDMI IN
RC
IT
IMPEDANCE
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
CENTER
SUBWOOFER
OUT
PR/CR
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
! CAUTION
If Bi-amp is active, you may encounter a restricted access if you have not removed the shorting bar
(like a jumper) in both tweeter and subwoofer ports in the front speaker.
Before you can use bi-amp, ensure that you use a speaker that supports bi-amplifying.
✎NOTE
To enable the Bi-Amp feature, you must set Surround Back Setup to Bi-AMP in Settings menu. See page 41.
With the Bi-AMP feature, you can use up to 5.1 channels for speaker output in the main unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
English
Connecting External Devices/your TV via HDMI
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set-top box and more.
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
HDTV Tuner
(HDTV Terrestrial Receiver)
or
SAT (Satellite/Set top box)
Game Console
Camcorder
or
LAN
iPod
IMPEDANCE
SURROUND BACK
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
/FRONT HEIGHT
CENTER
SUBWOOFER
OUT
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
•
Connect it if you want to use
Anynet+. (If connected TV support
ARC, it is not necessary to
If your TV supports ARC
function, connect to ARC
support port of TV.
OPTICAL
OUT
connect the OPTICAL OUT.)
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV
must support High-bandwidth Digital Content Protection System (HDCP). This product supports
HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
A TV with a DVI-D jack (TV not supporting HDCP)
Video
-
✎NOTE
Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is
protected by CPPM, use a product supporting CPPM.
The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
25
Connections
Connecting to your TV
HDMI OUT
HDMI IN
LAN
iPod
IMPEDANCE
SURROUND BACK
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
/FRONT HEIGHT
CENTER
SUBWOOFER
OUT
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
(not supplied)
or
or
VIDEO
IN
COMPONENT
IN
OPTICAL
OUT
AUDIO
OUT
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not supplied) from
the Component Video Output (PR, PB and Y) jacks on the back of your Receiver to the Component Video Input
jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your Receiver to the Video Input
jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your Receiver to the Audio Out of the TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
English
Connecting a Cable, Satellite or Set-top Box
COMPONENT
IN
VIDEO
IN
or
(not supplied)
HDMI OUT
HDMI IN
LAN
iPod
IMPEDANCE
SURROUND BACK
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
/FRONT HEIGHT
CENTER
SUBWOOFER
OUT
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
or
SAT(Cable/Satellite/Set-top box)
VIDEO
OUT
AUDIO
OUT
COMPONENT OPTICAL
OUT OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks on the
back of your Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable from the VIDEO IN (SAT) jack on the back of your Receiver to the Video Output jack on
your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your Receiver to the Audio Out of the SAT.
✎NOTE
Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
27
Connections
Connecting a Game Console
COMPONENT
IN
VIDEO
IN
(not supplied)
or
HDMI OUT
HDMI IN
LAN
iPod
IMPEDANCE
SURROUND BACK
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
/FRONT HEIGHT
CENTER
SUBWOOFER
OUT
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
Game Console
AUDIO
OUT
VIDEO COMPONENT OPTICAL
OUT
OUT OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (Game) (PR, PB and Y) jacks on the
back of your Receiver to the Component Video Output jacks on your Game Console.
OR
Connect a Video cable from the VIDEO IN (Game) jack on the back of your Receiver to the Video Output jack on
your Game Console.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your Receiver to the Digital Output of the Game Console.
OR
Connect AUDIO IN (Game Console) on your Receiver to the Audio Out of the Game Console.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
English
Connecting a CD Player
CD Player
AUDIO
OUT
COAXIAL
OUT
(not supplied)
(not supplied)
or
HDMI OUT
HDMI IN
LAN
iPod
IMPEDANCE
SURROUND BACK
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
FRONT
SURROUND
SURROUND
FRONT
/FRONT HEIGHT
CENTER
SUBWOOFER
OUT
AUDIO IN
IN
OUT
SPEAKERS OUT
FM ANT
Audio Connection
Connect the Digital Input (COAXIAL) on your Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your Receiver to the Audio Out of the CD player.
✎NOTE
If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the
main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
29
Connections
Video Conversion Flow According to the Connected Port
As shown in the illustration, if the unit’s HDMI Out is connected to a TV or monitor, the analog video source
(composite or component) from the video device is processed for up-conversion automatically for HDMI output.
If connected to a TV or monitor through Composite or Component ports, corresponding analog signal will be
output respectively, without any conversion. In case if the unit and video source device is connected in multiple
methods (Component and Composite video) at the same time: Video input signal is automatically selected in the
order of Component Video ¨ Composite Video.
LAN
iPod
HDMI OUT
HDMI IN
ARC
(MONITOR)
HDMI
1
HDMI
2
HDMI
3
HDMI 4
(AUX2)
(SAT)
(GAME)
(AUX1)
SPEAKER IMPEDANCE : 4~8
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
SURROUND BACK
/FRONT HEIGHT
SURROUND BACK
/FRONT HEIGHT
1
2
FRONT
SURROUND
SURROUND
FRONT
SAT
GAME
TV
MONITOR
CENTER
(SAT)
(GAME)
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
GAME
TV
CD
OPTICAL
(SAT)
1
OPTICAL
(GAME)
2
OPTICAL
(TV)
3
COAXIAL
(CD)
FM ANT
AUDIO IN
IN
OUT
SPEAKERS OUT
Input
Signal
Output
Signal
Video
Conversion
HDMI IN
HDMI OUT
HDMI IN
HDMI OUT
COMPONENT OUT
VIDEO OUT
COMPONENT IN
VIDEO IN
COMPONENT OUT
VIDEO OUT
COMPONENT IN
VIDEO IN
✎NOTE
This enables upconverting up to a quality of 1080p.
Auto conversion is not applied to a video source incoming from HDMI IN port.
The maximum resolution of the input video signal is 480i, and it will not support higher input resolution.
Video conversion is compatible with the NTSC color system only.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
English
Connecting the FM Antenna
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall
or other rigid surface.
HDMI OUT
HDMI IN
LAN
iPod
)
VIDEO IN
VIDEO OUT
COMPONENT IN/OUT
F
SUBWOOFER
OUT
FM ANT
AUDIO IN
IN
OUT
FM ANT
FM antenna (supplied)
✎NOTE
Do not place the antenna cable close to the power cord. Keep it as far away as possible.
If you experience poor FM reception, use an external antenna.
Connecting AUX Components
You can connect external devices you use for a short time (camcorder, game console, mobile
equipment,etc.) to the front of this unit for convenience.
INPUT SELECT
MASTER VOLUME
ASC MIC
VIDEO
AUDIO
PHONES
SELECT
TONE
CONTROL
TUNING
MODE
AUDIO
ASSIGN
AUDIO
EFFECT
Smart HUB
S.Direct
vTuner
AV SYNC
MEMORY
MENU
RETURN
3D SOUND
AUX
1
IN
(not supplied)
Camcorder
AUDIO
OUT
VIDEO
OUT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
31
Connections
Connecting to a Network
You can connect this product to a network and use network based services such Smart Hub and BD-
LIVE (See pages 70~79), as well as receive software upgrades through the network connection. We
recommend using a wireless router or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
terminal of your modem.
2. Set the network options. (See page 47)
HDMI OUT
MDMI IN
LAN
iPod
Router
Broadband modem
(with integrated router)
Or
Broadband modem
Broadband
Broadband
service
service
Networking with PC for
AllShare function
(See page 79)
✎NOTE
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
DSL users, please use a router to make a network connection.
To use the AllShare function, you must connect your PC to the network as shown in the figure.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
English
Wireless Network
You can connect the Receiver to your network through a wireless IP sharer (router). To set the network
configuration options. see page 47.
Broadband
service
Wireless IP sharer
INPUT SELECT
MASTER VOLUME
PC
Networking with PC for
AllShare function
(See page 79)
✎NOTE
To use a wireless network, your product must be connected to a wireless IP sharer (router). If the wireless IP sharer
supports DHCP, your product can use a DHCP (dynamic) or static IP address to connect to the wireless network.
This product supports IEEE 802.11b,g and n. We recommend using IEEE 802.11n. When you play video
over a IEEE 802.11b or g connection, the video may not play smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP
sharer is currently being used by another device nearby, this will result in interference and communication failure.
If you select the Pure High-throughput (Greenfield) 802.11n mode and set your routers's Security Encryption
type to WEP, TKIP or TKIPAES (WPS2Mixed), your Samsung home theater will not support the connection in
compliance with new Wi-Fi certification specifications.
If your router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button
Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA
key in either mode.
You can set up the wireless network connection in three ways:
- Using Auto Setup (the Auto Network Search function) through Wireless (General)
- Using WPS(PBC)
- Using One Foot Connection
Wireless LAN, by its nature, may cause interference, depending on the operating conditions.
(router performance, distance, obstacles, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
The home theater supports the following security protocols only:
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, AES
To use the AllShare function, you must connect your PC to your network as shown in the figure.
The connection can be wired or wireless.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
33
Setup
•
Home Menu
Initial Settings
1. Turn on your TV after connecting the product.
When you connect and turn on the product to a
TV for the first time, the Initial Settings screen
appears.
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
Initial Settings | On-Screen Language
Select a language for the on-screen displays.
Български
Dansk
Hrvatski
Nederlands
Suomi
Čeština
English
Français
Magyar
한국어
d
WPS(PBC)
Eesti keel
Deutsch
Indonesia
Ελληνικά
Italiano
✎ NOTE
m
Move
"
Enter
The Home menu will not appear if you do not
configure the initial settings except as noted
below.
If you press the BLUE (D) button during the
network setup, you can access the Home
menu even if the network setup is not
completed yet.
If you want to display the Initial Setting screen
again to make changes, select the Initial
Settings. (See page 51)
If you use an HDMI cable to connect the
product to an Anynet+(HDMI-CEC)-
2. Press the ▲▼◄► buttons to select the desired
language, and then press the ENTER button.
3. Press the ENTER button to select Start.
4. Press the ▲▼ buttons to select the desired TV
Aspect Ratio, and then press the ENTER button.
(See page 37)
If you press the BLUE (D) button to skip
Network Setup, you can access the Home
menu even the Network Setup is not completed.
compliant Samsung TV and 1.) You have set
the Anynet+(HDMI-CEC) feature to On in
both the TV and the product and 2.) You have
set the TV to a language supported by the
product, the product will select that language
as the preferred language automatically.
If you leave the product in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the product is
left in the screen saver mode for more than 20
minutes, the power will automatically turn off.
5. Press the ▲▼ buttons to select the desired
Network Settings : Wired, Wireless
(General), WPS(PBC) or One Foot
Connection, and then press the ENTER
button. If you do not know the details of your
Network Settings, press the BLUE (D) button
on your remote instead to skip Network
Settings here, finish the Initial Settings, and
go to the Home menu.
If you selected a Network Settings, go to
pages 47~50 for more information about the
Network settings. When done, go to Step 6.
6. The Home menu appears. (For more
information about the Home menu, please
see page 35.)
Download from Www.Somanuals.com. All Manuals Search And Download.
34
English
2. Press the ◄► buttons to select Settings,
Accessing the Settings Menu
and then press the ENTER button.
DISC MENU
TITLE MENU
POPUP
3. Press the ▲▼ buttons to select the desired
submenu, and then press the ENTER
button.
1
2
TOOLS
INFO
4. Press the ▲▼ buttons to select the desired
item, and then press the ENTER button.
3
4
5. Press the EXIT button to exit the menu.
NOTE
✎
TUNER
When the product is connected to a network,
select Internet from the Home menu.
Download the desired content from Samsung
Apps. (See pages 77~79)
1
MENU Button : Press to move to the Home menu.
2
3
4
RETURN Button : Return to the previous menu.
The access steps may differ depending on the
menu you selected.
The OSD (On Screen Display) may change in
this product after you upgrade the software
version.
ENTER / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
EXIT Button : Press to exit the current menu.
To access the Settings menu and sub-menus,
follow these steps:
1. Press the POWER button.
The Home Menu appears.
•
Home Menu
My Contents
Videos
Photos
3
4
Music
1
2
Function
My Devices
Internet
Settings
5
6
d
WPS(PBC)
Selects My Devices.
Selects Function.
1
2
3
4
5
6
Selects My Contents.
Selects Internet.
Selects Settings.
Displays the buttons available.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
35
Setup
Depending on the content and the position of
the picture on your TV screen, you may see
vertical black bars on the left side, right side, or
both sides.
Display
You can configure various display options such as
the TV Aspect Ratio, Resolution, etc.
3D Settings
Screen Size
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
Lets you enter the actual screen size of your TV so
that the product can adjust the image according to
the screen size and display an optimal 3D image.
(The maximum allowed screen size is 116 inches for
this product.)
Settings
Display
Audio
3D Settings
3D Settings
Network
System
Languag
Security
General
Support
! CAUTION
3D Blu-ray Playback Mode : Auto
55
Screen Size
:
inch
If you want to enjoy 3D content, connect a
3D TV to the product’s HDMI OUT port
using a high-speed HDMI cable. Put on 3D
glasses before playing the 3D content.
>
Move
"
Enter
'
Return
The product outputs 3D signals only through
HDMI cable connected to the HDMI OUT
port.
3D Blu-ray Playback Mode
As the video resolution in 3D play mode is
fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
You can choose whether to watch a 3D Blu-ray
disc in 3D or 2D mode before playing the 3D
disc. It is automatically played in 2D mode if your
TV cannot support 3D contents.
•
•
•
Auto : Automatically detect the 3D capability of
the connected TV and play a 3D Blu-ray disc in 3D
or 2D accordingly.
3D 3D : 3D Blu-ray Discs are played in 3D
mode at all times. If a TV cannot support 3D Blu-
ray discs, the playing screen can be blank.
3D 2D : 3D Blu-ray Discs are played in 2D
mode at all times. Choose this to view a picture
without the 3D effect or when a TV cannot support
3D Blu-ray discs.
Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46 inch
screen, stay 138 inches (11.5 feet) from the
screen.
- Place the 3D video screen at eye level for
the best 3D picture.
When the product is connected to some 3D
devices, the 3D effect may not function
properly.
NOTE
✎
To stop a movie during 3D playback, press the
STOP() button once. The movie stops and the
3D mode option is de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the STOP() button
once. The Blu-ray menu appears. Press the
STOP() button again, then select 3D
Settings in the Blu-ray menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
English
TV Aspect
(Picture Size and Format)
BD Wise (Samsung Products only)
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect a Samsung product and a
Samsung TV with BD Wise to each other via HDMI,
and BD Wise is on in both the product and TV, the
product outputs video at the video resolution and
frame rate of the BD/DVD disc.
Depending on the type of television you have, you
may want to adjust the screen size setting.
•
16:9 Original : Select when you connect the
product to a 16:9 TV screen. The product will
display all content in its original aspect ratio.
Content formatted in 4:3 will be displayed with
black bars on the left and right.
•
Off : The output resolution stays fixed at the
resolution you set previously in the Resolution
menu, regardless of the resolution of the disc.
See Resolution below.
•
•
16:9 Full : Select when you connect the product
to a 16:9 TV screen. All content will fill the full
screen. Content formatted in 4:3 will be stretched.
4:3 Letter Box : Select when you connect the
product to a 4:3 TV screen. The product will
display all content in its original aspect ratio.
Content formatted in 16:9 will be displayed with
black bars on the top and bottom.
•
On : The product outputs video at the original
resolution and frame rate of the BD/DVD disc.
NOTE
✎
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD
Wise appears in the Resolution menu.
If the product is connected to a device that
does not support BD Wise, you can not use
the BD Wise function.
•
4:3 Pan-Scan : Select when you connect the
product to a 4:3 TV screen. 16:9 content will have
the extreme left and right portions cut off.
NOTE
✎
For proper operation of BD Wise, set the BD
Wise menu of both the product and the TV to On.
Depending on the disc type, some aspect ratios
may not be available.
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
Resolution
Lets you set the output resolution of the
Component and HDMI video signal to Auto,
1080p, 1080i, 720p, 480p, or 480i. The number
indicates the number of lines of video per frame.
The i and p indicate interlaced and progressive scan,
respectively. The more lines, the higher the quality.
If you select the 16:9 Original, your TV may
display 4:3 Pillarbox (black bars on sides of
picture).
Smart Hub Screen Size
Set the Smart Hub Screen to the optimal size.
•
Auto : Automatically sets the output resolution to
the connected TV’s maximum resolution.
•
•
•
Size 1 : The Smart Hub screen size will be smaller
than the default. You may see some black on
sides of screen.
Size 2 : This is the default setting for Smart Hub.
The product displays the normal Smart Hub
screen size.
Size 3 : This will display a larger Smart Hub screen
size. The image may be too large for your TV
screen.
•
BD Wise : Automatically sets the resolution to the
resolution of the BD/DVD disc if you have
connected the product via HDMI to a TV with the
BD Wise feature. (The BD Wise menu item appears
only if BD Wise is set to On. See BD Wise above.)
•
1080p : Outputs 1080 lines of progressive
video. (HDMI only)
•
•
•
1080i : Outputs 1080 lines of interlaced video.
720p : Outputs 720 lines of progressive video.
480p : Outputs 480 lines of progressive video.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
37
Setup
Resolution according to the output mode
•
Blu-ray Disc/E-contents/Digital Contents playback
HDMI / connected
HDMI / not connected
Component Mode
HDMI Mode
Output
Component/
VIDEO Mode
Setup
E-contents/
Digital
contents
E-contents/
Digital
VIDEO Mode
Blu-ray Disc
Blu-ray Disc
contents
Resolution of
Blu-ray Disc
BD Wise
1080p@60F
480i
480i
-
-
-
-
-
Max.
Resolution of
TV input
Max.
Resolution of
TV input
Auto
-
1080p@60F
1080p@60F
1080p@60F
480i
480i
-
-
-
-
-
-
Movie Frame :
Auto (24Fs)
1080p@24F
1080p@24F
1080i
720p
480p
480i
1080i
720p
480p
-
1080i
720p
480p
-
480i
480i
480i
-
480i
480i
480i
480i
1080i
720p
480p
480i
480i
480i
480i
480i
•
DVD playback
HDMI / connected
HDMI / not connected
Output
Component/VIDEO
Mode
Setup
HDMI Mode
Component Mode
VIDEO Mode
BD Wise
Auto
480i
480i
-
-
-
-
Max. Resolution of
TV input
480i
1080p@60F
1080i
1080p@60F
1080i
720p
480i
480i
480i
480i
-
-
-
480p
480p
480p
480i
480i
480i
480i
480i
720p
480p
480p
480i
-
✎NOTE
If the TV you connected to the product does not support Movie Frame or the resolution you selected,
the message “If no pictures are shown after the selection, please wait for 15 seconds. And then, the
resolution will be reverted to the previous value automatically. Would you like to make a selection?”
appears.
If you select Yes, the TV’s screen will go blank for 15 seconds, and then the resolution will revert to the
previous resolution automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
English
If the screen stays blank after you have
changed the resolution, remove all discs, and
then press and hold the STOP () button on
the front of the product for more than 5
seconds. All settings are restored to the
factory default. Follow the steps on the
previous page to access each mode and
select the Display Setup that your TV will
support.
When the factory default settings are restored,
all stored user BD data is deleted.
The Blu-ray Disc must have the 24 frame
feature for the product to use the Movie Frame
(24Fs) mode.
HDMI Deep Color
Lets you output video from the HDMI OUT jack
with Deep Color. Deep Color provides more
accurate color reproduction with greater color
depth.
•
Auto: The product outputs video with Deep
Color to a connected TV which supports HDMI
Deep Color.
•
Off : The picture is output without Deep Color.
Still Mode
Lets you set the type of picture the product
displays when you pause DVD playback.
If both HDMI and Component jacks are
connected and you are currently viewing
Component output, the resolution is fixed to
480i.
•
•
•
Auto: Automatically shows the best still picture
depending on the content.
Frame : Select when pausing a scene with a
little action.
Field : Select when pausing a scene with a lot
of action.
HDMI Color Format
Lets you set the color space format for HDMI
output to match the capabilities of the connected
device (TV, monitor, etc).
Progressive Mode
Lets you improve picture quality when viewing DVDs.
•
Auto : Automatically sets the product to the
•
Auto : Select to have the product automatically
select the best picture quality for the DVD
you’re watching.
optimum format supported by your device.
•
YCbCr (4:4:4) : If your TV supports the YCbCr
color space via HDMI, select this to output the
normal YCbCr color gamut.
RGB (Standard) : Select RGB (Standard) to
output the normal RGB color gamut.
RGB (Enhanced) : If you have connected the
product to a DVI display device such as a
monitor, select RGB (Enhanced) to output the
enhanced RGB color gamut.
•
Video : Select for the best picture quality from
concert or TV show DVDs.
•
•
Video Conversion
You can convert the incoming composite or
component video signal into a maximum quality of
the connected TV if you output the converted video
via HDMI OUT.
Movie Frame (24 Fs)
•
Auto :Converts the incoming video signal
before outputting in the maximum resolution
that the connected TV supports.
Setting the Movie Frame (24Fs) feature to Auto
allows you to adjust the product’s HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. You can select
Movie Frame only when the product is in the HDMI
1080i or 1080p output resolution modes.
•
Bypass : Converts the input video source into
the digital counterpart without changing the
resolution.
✎NOTE
A income signal supports only 480i.
•
•
Auto : Movie Frame (24Fs) functions work.
Off : Movie Frame (24Fs) functions are off.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
39
Setup
• Large : Select when using large speakers. You
can listen to full range sound.
Audio
• Small : Select this when using small speakers.
• None : Select when no speaker is used.
Speaker Settings
• On (subwoofer) : Select when using the
subwoofer speaker.
Settings
Speaker Settings
Display
Audio
• Off (subwoofer) : Select when not using the
subwoofer speaker.
Size
|
Network
System
Languag
Security
General
Support
Level
Distance
7.1 CH Connection
Test Tone
✎NOTE
:
:
Surround Back
Off
You can also use the ,,., <, >, ENTER
buttons on the front of your Receiver.
>
Move
"
Enter
'
Return
When the Surround Speaker in set to None,
you can not select Surround Back speaker.
Size
Level
Signal outputs and frequency response from the
speaker will be adjusted according to your
speaker configuration and whether certain
speakers are used or not.
You can adjust the balance and level for each
speaker.
Adjusting Front/Center/Surround/Surround
Back/Subwoofer Speaker Level
•
Each time you press the ▲▼ buttons, Front ꢀ
Center ꢀ Surround ꢀ Surround Back ꢀ
Subwoofer will be selected in turn.
• You can adjust the volume level in steps from
-10dB ~ +10dB.
• The sound gets louder as you move closer to
+10dB and quieter as you get closer to -10dB.
Settings
Size
|
Display
Audio
Front
◄
:
Large
Small
Small
Small
On
Settings
Network
System
Languag
Security
General
Support
Center
Level
Display
Audio
Surround
Surround Back
Subwoofer
Test Tone
:
Front L
Front R
Center
Surround L
Surround R
Surround Back L
Surround Back R
Subwoofer
Test Tone
◄
0 dB
|
:
Network
System
Languag
Security
General
Support
:
:
:
:
:
:
:
:
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Off
:
:
Off
>
Move
"
Enter
'
Return
>
Move
<
Change
'
Return
Setting the Speaker
Default
Setting
Speaker
Front
Possible Settings
Large, Small
Small
Center
Large, Small, None
Large, Small, None
Small
Small
Small
On
Surround
Surround Back Large, Small, None
Subwoofer On, Off
Download from Www.Somanuals.com. All Manuals Search And Download.
40
English
• Bi-AMP : Select this if you want to connect the
Bi-Amp compliant speaker to the surround
back port. With this setting, you can enable the
Bi-Amp feature.
Distance
If you cannot place the speakers at equal
distances from the listening position, you can
adjust the delay time of the audio signals from the
front, center, surround, surround back and
subwoofer speakers.
✎NOTE
Depending on the surround back settings,
the surround back speaker or front height
speaker menus may not be activated or
may differ in the speaker menu: Size, Level,
Distance.
•
You can set the Speaker Distance between
1ft (0.3m) and 30ft (9.0m).
Settings
Distance
Display
Audio
Depending on your setting, you may not
use different features simultaneously. If
you set Surround Back, for instance, you
cannot use the following features: PL IIz and
Bi-AMP.
Front L
Front R
Center
Surround L
Surround R
Surround Back L
Surround Back R
Subwoofer
Test Tone
◄
10(ft) 3.0(m)
|
Network
System
Languag
Security
General
Support
:
:
:
:
:
:
:
:
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
Off
>
Move
<
Change
'
Return
Test Tone
Use the Test Tone feature to check the speaker
connections.
7.1 CH Connection
Press the ◄, ► buttons to select On.
Settings for the surround back speaker differ
depending on the connection method and
installation site of the speaker to be connected.
You must configure the surround back settings
according to the connected speaker before you
listen to music properly.
•
A test tone will be sent to Front L ꢀ Center ꢀ
Front R ꢀ Surround R ꢀ Surround Back R
ꢀ Surround Back L ꢀ Surround L ꢀ
Subwoofer in order so you can make sure the
speakers are set up correctly.
To stop the test tone, press the ◄, ► buttons to
Settings
Speaker Settings
Display
select Off.
Audio
Size
Network
Level
Settings
System
Distance
Speaker Settings
Display
Languag
7.1 CH Connection
Test Tone
◄
Surround Back
Off
|
Security
General
Support
Audio
:
Size
Network
Level
System
Distance
>
Move
"
Enter
'
Return
Languag
7.1 CH Connection
Test Tone
:
Surround Back
On
Security
General
Support
◄
|
>
Move
"
Enter
'
Return
• Surround Back : Select this if you want to
install the surround back speaker in the default
settings. With this setting, you can enable the
Dolby Pro Logic IIx mode.
• PL IIz : Select this if you want to install the
surround back speaker in the top front corner.
With this setting, you can enable the Dolby Pro
Logic IIz mode.
✎NOTE
When HDMI Audio is ON (audio is produced
through TV speakers), the Test Tone
function is not available.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
41
Setup
✎
NOTE
Musical Room Calibration
Running the Musical Room Calibration
function takes about 3 minutes.
Make sure there is no disc in the product when
you run the Musical Room Calibration function.
If the ASC microphone is disconnected during the
Musical Room Calibration setup, the setup will be
canceled.
If the product is connected to external devices or
other components (such as an iPod, AUX, D.IN),
the Musical Room Calibration Setup may not work
properly.
By setting the Musical Room Calibration (MRC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 7.1-channel sound field optimized for
your environment.
ASC MIC
VIDEO
AUDIO
PHONES
AUX
1
IN
Noise may result in incorrect measurements.
Ensure the room is quiet when you run the
Musical Room Calibration.
I
PHONE
S
A
U
D
VIDEO
A
S
C
M
I
1
I
I
3
D
S
O
U
N
D
AUX
AU
FEC
D
O
T
N
A
S
S
D
G
IO
N
EF
RETUR
EMOR
Y
MENU
ASC
S
ELEC
T
M
v
T
u
n
e
r
A
V
SYNC
MO
TU E
N
D
ING
S
m
a
r
H
U
B
T
NT
N
R
OL
CO
microphone
Place the microphone in the main listening
position.
Make sure there are no objects between the
speakers and microphone.
Note that the test tones of the speakers may be
loud.
Musical Room Calibration Mode
Do not place the microphone behind furniture or
too close to the wall. Otherwise, it can produce an
incorrect test result.
You will hear either the Musical Room Calibration
mode or the User Speaker Settings.
•
Off: You will hear sound in the Speaker Setting
value.
•
On: You will hear sound in the Musical Room
Calibration mode.
Measurement
1. Plug the ASC microphone into the ASC IN jack.
2. Place the ASC microphone at the listening position.
•
Musical Room Calibration will be automatically
set up in the following sequence:
Front L ꢀ Center ꢀ Front R ꢀ Surround
R ꢀ Surround Back R ꢀ Surround Back
L ꢀ Surround L ꢀ Subwoofer
•
Press the RETURN button to cancel the
Musical Room Calibration Setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
English
Surround
Set surround sound effect-related functions.
Surround Mode and Input Signal Chart
o = active, – = inactive
Output Channel
Display Information
Surround
Mode
Input Signal
SL
SBL
L/R
C
SUBW
Signal Format
Channel Status
SR SBR
Dolby Digital
Dolby Digital
Dolby Digital EX
Dolby Digital +
ProLogic IIx
Dolby Digital +
ProLogic Iiz
Dolby Digital
Plus
O
O
O
O
O
O
–
O
O
O
Digital + Dolby Digital
Digital +Dolby Digital EX L, C, R, SL, SR ,SBL, SBR, SW
Digital + Dolby Digital
L, C, R, SL, SR ,SBL, SBR, SW
+ ProLogic IIx
Digital + Dolby Digital
L, C, R, SL, SR, H, SW
+ ProLogic Iiz
L, C, R, SL, SR ,SBL, SW
O
O
O
O
O
O
O
O
O
O
O (Height)
O
O
O
O
Dolby Digitital EX
Digital + Dolby Digital
L, C, R, SL, SR ,SBL, SBR, SW
Plus
Dolby Digital Plus
Dolby TrueHD
DTS (5.1-ch)
Dolby TrueHD
DTS Surround
DTS Digital +
ProLogic IIx
DTS Digital +
ProLogic Iiz
DTS-ES
DTS 96/24
DTS-HD Master
Audio
O
O
O
O
O
O
O
–
O
O
Dolby TrueHD
DTS
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SW
DTS-ES
O
O
O
O
O
O
O
O
O
DTS + ProLogic IIx
L, C, R, SL, SR ,SBL, SBR, SW
O (Height)
DTS + ProLogic Iiz
L, C, R, SL, SR ,SBL, SBR, SW
DTS 96/24
O
O
O
O
O
O
O
–
O
O
DTS ES
DTS 96/24
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SW
O
O
O
O
O
O
O
O
O
O
DTS-HD MSTR
L, C, R, SL, SR ,SBL, SBR, SW
DTS-HD
DTS-HD High
Resolution
DTS-HD
L, C, R, SL, SR, SBL, SBR, SW
Multi-Channel
Multi-Channel
Stereo
O
O
O
O
O
–
O
O
–
O
O (Height)
–
O
O
O
Digtal + LPCM
Digtal + LPCM
Digtal + LPCM
Digtal + LPCM
+ Dolby Digital +
ProLogic IIx
Digtal + LPCM
+ Dolby Digital +
ProLogic Iiz
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, R, SW
LPCM Multi-Channel
ProLogic IIx
O
O
O
O
O
O
O
O
O
L, C, R, SL, SR ,SBL, SBR, SW
2-ch PCM
ProLogic Iiz
O (Height)
L, C, R, SL, SR, H, SW
Digtal + LPCM + DTS
+ NEO:6
Digital + LPCM + LIVE
SURR
NEO:6
SFE
O
O
O
O
O
O
O
O
O
O
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
Multi-Channel
Multi-Channel
Stereo
O
O
O
O
O
–
O
O
–
O
O (Height)
–
O
O
O
Analog
Analog
Analog
Analog + Dolby Digital
+ ProLogic IIx
Analog + Dolby Digital
+ ProLogic Iiz
Analog + DTS NEO:6
Analog + LIVE SURR
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, R, SW
Analog Multi-Channel
Analog 2-ch
ProLogic IIx
O
O
O
O
O
O
O
O
O
L, C, R, SL, SR ,SBL, SBR, SW
ProLogic Iiz
O (Height)
L, C, R, SL, SR, H, SW
NEO:6
SFE
O
O
O
O
O
O
O
O
O
O
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
L/R : front speaker (left/right)
SL/SR : surround speaker (left/right)
C : center speaker
SBL/SBR : surround back speaker (left/right)
SW : subwoofer
Download from Www.Somanuals.com. All Manuals Search And Download.
English
43
Setup
✎NOTE
• Off : Dolby Digital Surround EX / DTS ES
decoder will not be used for playback.
Channel status displays are dependent on the
speaker configuration.
• On : Dolby Digital or DTS signal will be played
in 6.1 / 7.1 channel using Dolby Digital
Surround EX / DTS ES decoder.
SFE mode works with 2-ch signals.
If Dolby Pro Logic IIz is set to On, Dolby true
HD, Dolby plus, DTS-HD Master Audio, SFE
and NE0:6 will be output 5.1 channel.
✎NOTE
You cannot use DTS-ES without surround
back speakers connected.
DPL IIx
• Panorama : You can set it On or Off.
DTS Neo:6 Center Image
(This mode extends the front stereo image to
include the surround speakers for an exciting
"wraparound" effect with side wall imaging.)
You can play back 2 channel sound over 6.1
channels when enjoying music or a movie.
•
You can set Center Image from 0 to 5.
• Dimension : You can set from -7 to +7.
(Incrementally adjusts the sound field (DSP)from
the front or surround.)
• Center Width : You can set from 0 to 7.
(This sets the width of the center sound image.
The higher the setting, the less sound comes
from the center speaker.)
This parameter adjusts the height of the center
image through the front and center speakers.
“0” is the lowest while “5” is the highest.
✎NOTE
NEO:6 mode cannot be used with Dolby
Digital, Dolly Digital Plus, Dolby True HD,
DTS, DTS-HD Master Audio.
Extended Surround (EX/ES)
Pro Logic works only for PCM audio signals
with sampling frequencies of 32KHz, 44KHz
or 48KHz.
When surround back speakers are connected,
you can listen to 6.1 or 7.1 multi-channel sound
using the built-in Dolby Digital Surround EX or
DTS ES decoder. This function works when a
Dolby Digital or DTS source is input, and does
not work with L.PCM and Dolby Digital 2 channel
sources.
Crossover Frequency
Select the crossover frequency for the best bass
response in your speakers.
•
You can set frequencies 60, 80, 100,120, 150,
180 or 200(Hz).
• Auto : If the unit receives an audio signal that it
can recognize, it will select an optimal decoder
for playback in 6.1/7.1 channels.
If the amplifier does not recognize the audio
signal, it will not play in 6.1/7.1 channel
automatically.
MP3 Enhancer
This also helps enhance your sound experience
(ex. mp3 music). You can upscale your MP3 level
sound (24 kHz, 8bit) to CD level sound (44.1 kHz,
16bit).
Smart Volume
This will regulate and stabilize the volume level
against a drastic volume change when changing
channels or during a scene transition.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
English
Dual Mono
Digital Output
You set the Digital Output to match the
capabilities of the AV device you’ve connected to
the product :
Dual mono programs have two independent
mono channels.
You can use this function when dual mono
programs are played.
•
PCM : Choose if you have connected an HDMI
supported AV device.
When you use this function, select audio
channels CH1, CH2 or both Channel.
•
Bitstream (Unprocessed) : Select if you have
connected an HDMI supported AV device with
Dolby TrueHD and DTS-HD Master Audio
decoding capabilities.
• Ch 1 : Channel 1 is heard only.
• Ch 2 : Channel 2 is heard only.
• Both Channels : Both channels are heard from
front speakers.
•
•
Bitstream (Re-encoded DTS) : Choose if you
have connected an AV device using a Digital
Optical input that can decode DTS.
Bitstream (Re-encoded Dolby D) : Select if
you don’t have an HDMI supported AV device,
but have an AV device with Dolby Digital
decoding capabilities.
HDMI Audio
The audio signals transmitted over the HDMI
Cable can be toggled On/Off.
•
Off : Video is transmitted over the HDMI
connection cable only, and audio is output
through your product speakers only.
For more details, please refer to the digital output
selection table. (See page 46)
•
On : Both video and audio signals are transmitted
over the HDMI connection cable, and audio is
output through your TV speakers only.
✎
NOTE
Digital Output can be activated when HDMI
Audio is ON.
✎NOTE
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
If the HDMI device (AV device, TV) is not
compatible with compressed formats (Dolby
digital, DTS), the audio signal outputs as PCM.
HDMI Audio is automatically down-mixed to
2ch for TV speakers.
Audio Return Channel
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
You can enjoy TV sound from the Home Theater
speakers by using just one HDMI cable.
•
Auto : Listen to TV sound from the Home
Theater speakers if your TV is compatible with
the Audio Return Channel function.
This Digital Output setup does not effect the
analog (L/R) audio or HDMI audio output to
your TV.
•
Off : Turn the Audio Return Channel function
off.
It effects the optical and HDMI audio output
when your product is connected to an AV
NOTE
✎
When Anynet+ (HDMI-CEC) is Off, the Audio
Return Channel function is not available.
device
.
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
Using an ARC (Audio Return Channel)
uncertified HDMI cable may cause a
problem in compatibility.
ARC function is only available if an ARC-
compliant TV is connected.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
45
Setup
Digital Output Selection
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
Bitstream
(Unprocessed)
Setup
PCM
HDMI supported HDMI supported HDMI supported HDMI supported
Connection
PCM
AV device
AV device
AV device
AV device
Re-encoded
Up to 7.1ch
PCM
DTS re-encoded
Dolby Digital *
Re-encoded
Dolby Digital
Dolby Digital Plus
Up to 7.1ch
Up to 7.1ch
Up to 7.1ch
Up to 6.1ch
Up to 7.1ch
Up to 7.1ch
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
DTS
DTS re-encoded
DTS re-encoded
DTS re-encoded
DTS re-encoded
DTS re-encoded
DTS re-encoded
Dolby Digital *
Re-encoded
Dolby Digital *
Audio Stream on
Dolby TrueHD
Blu-ray Disc
Re-encoded
Dolby Digital *
Re-encoded
DTS
Dolby Digital *
Re-encoded
DTS-HD HRA
DTS-HD HRA
DTS-HD MA
Dolby Digital *
Re-encoded
DTS-HD MA
PCM
Dolby Digital *
PCM 2ch
Up to 5.1ch
Up to 6.1ch
PCM 2ch
Dolby Digital
DTS
PCM 2ch
Dolby Digital
DTS
PCM 2ch
Dolby Digital
DTS
Audio Stream
Dolby Digital
on DVD
DTS
Outputs only the
Decodes the main
Decodes the main
feature audio and
BONUSVIEW audio
stream together into
main feature audio feature audio and
Decodes the main
feature audio and
BONUSVIEW audio
stream together
stream so that
BONUSVIEW audio
stream together
your AV device can
Definition for
Any
decode the audio into PCM audio and PCM audio and adds
Blu-ray Disc
bitstream.
You will not hear Sound Effects, then
BONUSVIEW
re-encodes the
adds Navigation
Navigation Sound
Effects, then re-
encodes the PCM
into PCM audio and
adds Navigation
Sound Effects.
audio or Navigation PCM audio into DTS audio into Dolby digital
Sound Effects.
bitstream.
bitstream or PCM.
* If the Source Stream is 2ch, “Re-encoded Dolby D” Setting are not applied. Ouput will be LPCM 2ch.
Blu-ray Discs may include three audio streams :
- Navigation Sound Effects : When you choose
some menu navigation, Navigation Sound
Effects may sound. Navigation Sound Effects
are different on each Blu-ray Disc.
- Main Feature Audio : The audio soundtrack of
the main feature.
-
BONUSVIEW audio : An additional
soundtrack such as the director or actor’s
commentary.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
English
Dynamic Range Control
Network Settings
You can listen at low volumes, but still hear dialog
clearly. This is only active if your product detects
a Dolby Digital signal.
To begin setting up the network connection for
your product, follow these steps:
1. In the Home menu, press the ◄► buttons to
select Settings, and then press the ENTER
button.
•
Auto : The Dynamic Range Control will be set
automatically based on the information
provided by the Dolby TrueHD Soundtrack.
2. Press the ▲▼ buttons to select Network, and
then press the ENTER button.
•
•
•
Minimum : This slightly compresses the
dynamic range.
3. Press the ▲▼ buttons to select Network
Standard : This is standard setting for regulate
home use.
Maximum (Night Mode) : This greatly
compresses the dynamic range and lets you
view movies late at night at low volumes.
Settings, and then press the ENTER button.
4. Press the ▲▼ buttons to select Wired, Wireless
(General), WPS(PBC) or One Foot Connection,
and then press the ENTER button.
5. If you have a wired network, go to Wired Network
below. If you have a wireless network, go to
Wireless Network on pages 48~50.
HDMI Auto Sync
The Receiver can be set to automatically correct
any delay between the video and the audio,
based on the data from the connected TV.
Wired Network
•
Auto : Automatically adjust output timing of
audio and video if your TV supports and
automatic lipsync function.
Setting Up a Wired Connection - Auto
1. Press the ▲▼ buttons to select Wired.
•
Off : HDMI Auto Sync is disabled.
Settings
Network Settings
Display
Audio
Audio Sync
Select a network connection type.
Network
System
Languag
Security
General
Support
Wired
Video may fall out of sync with the audio when
the product is connected to a digital TV. If this
occurs, adjust the audio delay time to match the
audio to the video.
Wireless
(general)
Connect to the network using LAN cable. Please make
WPS(PBC)
sure that the LAN cable is connected.
One Foot
Connection
>
Move
"
Enter
'
Return
•
You can set the audio delay time between 0 msec
and 240 msec. Set it to the optimal status.
2. Press the ENTER button.
Network
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
Before you begin, contact your ISP to find out if
your IP address is static or dynamic. If it is
dynamic, and you are using a wired or wireless
connection, we recommend using the Auto
procedures. If you are using a wireless
connection and your router has the capability,
you can use WPS(PBC) or One Foot Connection.
Setting Up a Wired Connection - Manual
If you have a static IP address or the Auto Setting
does not work, you’ll need to set the Network
Settings values manually.
If your IP address is static, you must use the
manual set up procedure for both wired and
wireless connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
47
Setup
To view your Network Settings values on most
Windows computers, follow these steps:
11. Press the ENTER button to select OK.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
1. Right click the Network icon on the bottom
right of the Windows desktop.
2. In the pop-up menu, click Status.
Wireless Network
3. On the dialog that appears, click the Support
You can setup a wireless network three ways:
tab.
•
•
•
Wireless (General)
Using WPS(PBC).
One Foot Connection
4. On the Support tab, click the Details button.
The Network settings are displayed.
To enter the Network settings into your product,
follow these steps:
Wireless (General) includes both Automatic and
Manual setup procedures.
1. Press the ▲▼ buttons to select Wired, and
Setting Up the Wireless Network Connection
- Auto
then press the ENTER button.
2. Press the ◄► buttons to select IP Settings,
Most wireless networks have an optional security
system that requires devices that access the
network to transmit an encrypted security code
called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word
or a series of letters and numbers of a specified
length you were asked to enter when you set up
security for your wireless network. If you use this
method of setting up the network connection,
and have a Security Key for your wireless
and then press the ENTER button.
Settings
IP Settings
Display
Audio
IP Mode
Manual
0
0
0
0
0
0
0
0
0
0
0
0
IP Address
.
.
.
.
.
.
.
.
.
Network
System
Languag
Security
General
Support
Subnet Mask
Gateway
DNS Mode
DNS Server
Manual
0
0
0
0
.
.
.
OK
m
Move
Number
"
Enter
'
Return
network, you will have to enter the Pass Phrase
during the Auto setup process.
1. Press the ▲▼ buttons to select Wireless
(General).
3. Press the ENTER button to select IP Mode.
4. Press the ▲▼ buttons to select Manual,
Settings
and then press the ENTER button.
Network Settings
Di
Select a network connection type.
Au
5. Press the ▼ button to go to the first entry
Ne
Wired
field (IP Address).
Sy
Wireless
La
Se
Ge
6. Use the number buttons on your remote to
(general)
Set up wireless network by selecting your Wireless
Router. You may need to enter security key depending
on the setting of the Wireless Router.
WPS(PBC)
One Foot
enter numbers.
Connection
Su
7. When done with each field, press the ►
button to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
>
Move
"
Enter
'
Return
2. Press the ENTER button.
8. Enter the IP Address, Subnet Mask, and
When done, it displays a list of the available
networks.
Gateway values.
9. Press the ▼ button to go to DNS Mode.
3. Press the ▲▼ buttons to select the desired
network, and then press the ENTER button.
The Security screen appears.
10. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
English
4. On the Security screen, enter your network’s
Pass Phrase. Enter numbers directly using
your remote control.
To enter the Network settings into your product,
follow these steps:
1. Follow Steps 1 through 5 in the ‘Setting Up
the Wireless Network Connection - Auto’
procedure.
To select a letter, press the ▲▼◄► buttons
to move the cursor, then press the ENTER
button.
2. When done, press the ▲▼◄► buttons to
move the cursor to Done, and then press the
ENTER button. The Network Status screen
appears.
Settings
Display
Audio
Network Settings
Enter security key.
0 entered
Network
System
Languag
Security
General
Support
a
g
b
h
n
t
c
d
j
e
k
f
l
1
4
7
y
2
3
6
9
0
i
5
8
z
Settings
m
s
o
p
v
q
r
x
IP Settings
Display
u
*
w
Audio
IP Mode
Manual
a/A
Delete
Space
Done
0
0
0
0
0
0
0
0
0
0
0
0
IP Address
.
.
.
.
.
.
.
.
.
Network
System
Languag
Security
General
Support
a
Previous
m
Move
"
Enter
'
Return
Subnet Mask
Gateway
DNS Mode
DNS Server
Manual
0
0
0
0
.
.
.
OK
NOTE
✎
>
Move
"
Enter
'
Return
You should be able to find the Pass Phrase on
one of the set up screens you used to set up
your router or modem.
3. On the Network Status screen, select
Cancel, and then press Enter.
5. When done, press the ▲▼◄► buttons to
move the cursor to Done, and then press the
ENTER button.
4. Press the ◄► buttons to select IP Settings,
and then press the ENTER button.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
5. Press the ENTER button to select IP Mode.
6. Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
Setting Up the Wireless Network Connection
- Manual
7. Press the ▼ button to go to the first entry
field (IP Address).
8. Use the number buttons to enter numbers.
If the Auto Setting does not work, you need to
enter the Network settings values manually.
To view the Network Settings values on most
Windows computers, follow these steps:
9. When done with each field, press the ►
button to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
1. Right click the Network icon on the bottom
10. Enter the IP Address, Subnet Mask, and
right of the screen.
Gateway values.
2. In the pop-up menu, click Status.
11. Press the ▼ to go to DNS Mode.
3. On the dialog that appears, click the Support
12. Press the ▼ button to go to the first DNS
tab.
entry field. Enter the numbers as above.
4. On the Support tab, click the Details button.
13. The Network Status screen appears. The
product connects to the network after the
network connection is verified.
The Network settings are displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
49
Setup
2. Press the ENTER button.
WPS(PBC)
3. Place the Samsung Wireless Router within
25 cm (10 inches) of your product to
connect.
The easiest way to set up the wireless network
connection is using the WPS(PBC) function or the
One Foot Connection function.
If your wireless router has a WPS(PBC) button,
follow these steps:
4. Wait until the connection is automatically
established.
1. Press the ▲▼ buttons to select WPS(PBC).
Network Status
Settings
Check whether a connection to the network and
the Internet have been established.
Network Settings
Dis
Select a network connection type.
Au
Ne
Sy
Wired
S
Wireless
Network Status
La(general)
Di
Connect to the Wireless Router easily by pressing the
WPS(PBC) button. Choose this if your Wireless Router
supports Push Button Configuration(PBC).
MAC Address
IP Address
Subnet Mask
Gateway
XX:XX:XX:XX:XX:XX
0.0.0.0
Se
Ge
Su
WPS(PBC)
Au
0.0.0.0
One Foot
Ne
KT_WLAN
0.0.0.0
Connection
DNS Server
0.0.0.0
Sy
>
Move
"
Enter
'
Return
Internet is connected successfully.
La
If you have a problem using any Internet services, contact your Internet service
provider.
Se
Ge
Su
Network Settings
IP Settings
Retry
OK
2. Press the ENTER button.
<
Move
"
Enter
'
Return
3. Press the WPS(PBC) button on your router
within two minutes. Your product displays
the Network Selection Screen, and
automatically acquires all the network
settings values it needs and connects to your
network. When it is done, it displays an OK
button. Press the ENTER button on your
remote.
BD-LIVE Internet Connection
Set to allow or prohibit an Internet connection
when you use the BD-LIVE service.
•
Allow (All) : The Internet connection is allowed
for all BD-LIVE contents.
•
Allow (Valid Only) : The Internet connection is
allowed only for BD-LIVE contents containing a
valid certificate.
Prohibit : No Internet connection is allowed for
any BD-LIVE content.
One Foot Connection
You can set up the wireless connection
automatically if you have a Samsung Wireless
Router which supports One Foot Connection. To
connect using the One Foot Connection function,
follow these steps:
•
NOTE
✎
1. Press the ▲▼ buttons to select One Foot
What is a valid certificate?
Connection.
When the product uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the product.
Settings
Network Settings
Dis
Select a network connection type.
Au
Ne
Wired
Sy
Wireless
The Internet connection may be restricted
La
Se
Ge
(general)
Connect to your wireless network automatically if your
Wireless Router supports One Foot Connection. Select
this connection type after placing the Wireless Router
within 10 inches(25cm) of product.
while you are using BD-LIVE contents.
WPS(PBC)
One Foot
Connection
Su
>
Move
"
Enter
'
Return
Download from Www.Somanuals.com. All Manuals Search And Download.
50
English
•
•
•
Available Size : Available memory in the
System
device.
Delete BD Data : Delete all BD data in the
Initial Settings
storage.
Select Device : Change location of desired
By using the Initial Settings function, you can set
the language, Network Settings, etc.
For more information about the Initial Settings
function, refer to the Initial Settings section of this
user manual. (See page 34)
memory to store BD data.
NOTE
✎
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
Only those USB devices formatted in the FAT
file system (DOS 8.3 volume label) are
supported. We recommend you use USB
devices that support USB 2.0 protocol with 4
MB/sec or faster read/write speed.
The Resume Play function may not work after
you format the storage device.
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products that
have the Anynet+ feature.
To operate this function, connect this product to
a Samsung TV with an HDMI cable.
With Anynet+ on, you can operate this product
using a Samsung TV remote control and start
disc playback simply by pressing the PLAY (►)
button on the TV’s remote control.
For more information, please see the TV user
manual.
The total memory available to BD Data
Management may differ, depending on the
conditions.
Input Selection
•
•
Off : Anynet+ functions will not work.
On : Anynet+ functions will work.
Set the default port of DIGITAL AUDIO IN for
each sources.
•
•
•
NOTE
✎
SAT : Select the desired input port for SAT
source.
GAME : Select the desired input port for GAME
source.
CD : Select the desired input port for CD
source.
This function is not available if the HDMI cable
does not support CEC.
If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
Time Zone
BD Data Management
You can specify the time zone that is applicable
to your area.
Lets you manage the downloaded contents you
accessed through a Blu-ray Disc that supports
the BD-LIVE service and stored on memory
device.
Settings
Time Zone
Display
Audio
You can check the device’s information including
the storage size, delete the BD data, or change
the memory device.
Network
System
Languag
Security
General
Support
GMT + 00:00
BD Data Management Screen Information :
London, Lisbon, Casablanca
<
Change
"
Save
'
Return
•
•
Current Device : Display the selected device.
Total Size : Total memory size of the device.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
51
Setup
After you have set your password, select an age
rating you want to set for the BD Parental Rating
and a rating level you want to set for the DVD
Parental Rating. The product will only play Blu-ray
discs rated at or below the age rating and DVD
discs rated below the numeric rating unless the
password is entered.
DivX® Video On Demand
Shows the registration code authorized for the
product. If you connect to the DivX web site and
register using that code, you can download the
VOD registration file. If you activate the VOD
registration using My Contents, the registration is
completed.
Larger numbers indicate more mature content.
NOTE
✎
BD Parental Rating
For more information about DivX(R) VOD,
visit "http://vod.divx.com".
This will prohibit playback of Blu-ray disc rated
above Parental Rating.
Reset
DVD Parental Rating
All settings will revert to the default except for the
network and Smart Hub settings. You need enter
the password for this function.
Prevent playback of DVD discs with specific
numerical ratings unless a password is entered.
NOTE
✎
Change Password
The default password is 0000.
Change the 4-digit password used to access
security functions.
Language
If you forgot your password
You can select the language you prefer for the
Home menu, disc menu, etc.
1. Remove the disc.
•
On-Screen Menu : Select the language for the
on-screen displays.
2. Press and hold the STOP () button on the
front panel for 5 seconds or more.
•
Disc Menu : Select the language for the disc
menu displays.
All settings will revert to the factory settings.
NOTE
✎
•
•
Audio : Select the language for disc audio.
Subtitle : Select the language for disc subtitles.
When the factory default settings are restored,
all the user stored BD data will be deleted.
NOTE
✎
The selected language will only appear if
it is supported on the disc.
General
Front Display
Security
Change the brightness of the front panel.
This function works in conjunction with Blu-ray
and DVD discs that have been assigned an age
rating or numeric rating that indicates the maturity
level of the content. These numbers help you
control the types of Blu-ray and/DVD discs that
your family can watch.
When you access this function for the first time,
the password setup screen appears. Enter a
desired 4-digit password using the number
buttons. (The default password is 0000.)
•
•
•
Auto : Dim during playback.
Dim : Dim the display window.
Bright : Brighten the display window.
NOTE
✎
You cannot change the brighness of the
Power button.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
English
The four methods are explained below.
Network Remote Control
By Internet
To upgrade by Internet, follow these steps:
The Network Remote Control function lets you
control your Blu-ray Home Theater from a remote
device such as a smart phone through a wireless
connection to your local area network.
To use the Network Remote Control function, follow
these steps:
1. Select By Internet, and then press the
ENTER button. The Connecting to Server
message appears.
2. If there is a download available, the
Download pop-up appears with a progress
bar and the download starts.
1. Select On in the Network Remote Control
menu.
2. Install the Samsung network remote control
application to control your product on your
compatible portable device.
3. When the download is complete, the
Upgrade Query window appears with three
choices: Upgrade Now, Upgrade Later, or
Don’t Upgrade.
4. If you select Upgrade Now, the product
upgrades the software, turns off, and then
turns on automatically.
5. If you do not make a selection in one minute
or select Upgrade Later, the product stores
the new upgrade software. You can upgrade
the software later using the By Downloaded
function.
3. Make sure your portable device and your
product are connected to the same wireless
router.
4. Start the application on your portable device.
The application should find your product and
display it on a list.
5. Select the product.
6. If this is the first time you are using the
function, it will ask you to allow or deny
remote control of the product. Select Allow.
6. If you select Don’t Upgrade, the product
cancels the upgrade.
7. Follow the instructions that came with the
NOTE
application to control the product.
✎
Your product must be connected to the
Internet to use the By Internet function.
The upgrade is complete when the product
turns off, and then turns on again by itself.
Never turn the product off or back on
manually during the update process.
Samsung Electronics shall take no legal
responsibility for product malfunction
caused by an unstable Internet connection
or consumer negligence during a software
upgrade.
Support
Software Upgrade
The Software Upgrade menu allows you to
upgrade the product’s software for performance
improvements or additional services. You can
upgrade in four ways:
•
•
•
•
By Internet
By USB
By Disc
If you want to cancel the upgrade while the
upgrade software is downloading, press the
ENTER button.
By Downloaded (File)
Download from Www.Somanuals.com. All Manuals Search And Download.
English
53
Setup
7. In the product’s menu, go to Settings >
By USB
Support > Software upgrade.
To upgrade by USB, follow these steps:
8. Select By Disc.
2. Download the latest USB software upgrade
NOTE
✎
zip archive to your computer.
When the system upgrade is done, check the
software details in the software Upgrade menu.
Do not turn off the product during the Software
Upgrade. It may cause the product malfunction.
3. Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
4. Copy the folder to a USB flash drive.
5. Make sure the disc tray is empty, and then
insert the USB flash drive into the USB port
of the product.
By Downloaded
The By Downloaded option lets you upgrade using
a file the product downloaded earlier but you
decided not to install immediately or a file
downloaded by the product in Standby Mode (See
Download in Standby Mode below).
6. In the product’s menu, go to Settings >
Support > Software Upgrade.
7. Select By USB.
To upgrade By Downloaded, follow these steps:
NOTE
✎
1. If upgrade software has been downloaded,
you will see the software version number to
the right of By Downloaded.
The disc tray must be empty when you
upgrade the software using the USB Host
jack.
When the software upgrade is done, check
the software details in the software Upgrade
menu.
Do not turn off the product during the
software upgrade. It may cause the product
to malfunction.
Software upgrades using the USB Host jack
must be performed with a USB memory
flash stick only.
2. Select By Downloaded, and then press the
ENTER button.
3. The product displays a message asking if
you want to upgrade. Select Yes. The
product begins the upgrade.
4. When the update is complete, the product
turns off automatically, and then turns on.
NOTE
✎
When the system upgrade is done, check the
software details in the software Upgrade
menu.
Do not turn off the product during the software
Upgrade. It may cause the product to
malfunction.
By Disc
To upgrade by Disc, follow these steps:
2. Download the latest disc software upgrade
zip archive to your computer.
To use the By Downloaded function, your
product must be connected to the Internet.
3. Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
4. Write the folder onto a disc. We recommend
a CD-R or DVD-R.
5. Finalize the disc before you remove it from
your computer.
6. Insert the disc into product.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
English
Download in Standby Mode
You can set the Download in Standby Mode
function so that the product downloads new
upgrade software when it is in Standby mode. In
Standby mode, the product is off, but its Internet
connection is active. This allows the product to
download upgrade software automatically, when
you are not using it.
To set Download in Standby Mode, follow these
steps:
1. Press the ▲▼ buttons to select Download
in Standby Mode, and then press the
ENTER button.
2. Select On or Off.
•
Off : If you select Off, the product will notify
you with a pop up message when new
upgrade software is available.
•
On : If you select On, the product will
automatically download new upgrade
software when it is in Standby mode with
the power off. If it downloads new upgrade
software, the product will ask you if you
want to install it when you turn the product
on.
NOTE
✎
To use the Download in Standby Mode
function, your product must be connected to
the Internet.
Contact Samsung
Provides contact information for assistance with
your product.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
55
Basic Functions
•
•
Audio CD (CD-DA)
track 1 track 2
Playing a Disc
track 3
track 4
track 5
Playback
1. Insert a disc into the disc slot with the disc's
label facing up.
MP3, WMA, DivX, MKV and MP4
folder (group) 1 folder (group) 2
2. Press the PLAY (►) button.
Playback related buttons
file 1 file 2 file 2
file 1
file 3
PLAY ( ►)
Starts playback.
Stops playback.
Playing a 2D video in 3D mode
•
If you press the button
once : The stop position is
memorized.
STOP ( )
hZ
•
If you press the button twice
: The stop position is not
memorized.
You can enjoy an ordinary 2D video in
3D mode.
✎NOTE
PAUSE ( )
Pauses playback.
If you move to the Home or Smart
Hub Home menu in 3D mode, it will switch
to 2D automatically.
✎NOTE
For some discs, the product may not
memorize the stop positon when you press the
Using the Disc menu/Title menu/
Popup menu
STOP (
) button.
Video files with high bit rates of 20Mbps or
more strain the product’s capabilities and
may stop playing during play back.
Using the Disc Menu
Disc Structure
hZ
DISC MENU
1. During playback, press the DISC
MENU button on the remote
control.
The content of discs are usually divided as shown
below.
•
Blu-ray Disc, DVD-VIDEO
2. Press the ▲▼◄ ► buttons to make
a selection, and then press the
ENTER button.
title 1
title 2
chapter 1 chapter 2 chapter 1 chapter 2 chapter 3
✎NOTE
Depending on the disc, the menu items may
differ and this menu may not be available.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
English
Using the Title Menu
Using the Search and Skip Functions
During playback, you can search quickly through
a chapter or track, and use the skip function to
jump to the next selection.
Z
TITLE MENU
1. During playback, press the TITLE
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to
make the desired selection, then
press the ENTER button.
POPUP
Searching for a Desired Scene
hzZyx
During playback, press the SEARCH ()
•
✎NOTE
button.
Depending on the disc, the menu items may
Each time you press the SEARCH ()
button, the playback speed will change as
follows.
differ and this menu may not be available.
The Title Menu will only be displayed if there
are at least two titles on the disc.
BD-ROM,
) 1 ) 2 ) 3
BD-RE/-R,
) 4 ) 5 ) 6 ) 7
Using the Popup Menu
DVD-RW/-R,
( 1 ( 2 ( 3
( 4 ( 5 ( 6 ( 7
DVD+RW/+R,
DVD-VIDEO
h
TITLE MENU
POPUP
) 1 ) 2 ) 3
( 1 ( 2 ( 3
1. During playback, press the POPUP
DivX, MKV, MP4
button on the remote control.
2. Press the ▲▼◄ ► buttons or
ENTER button to select the
desired menu.
•
To return to normal speed playback, press the
PLAY (►) button.
NOTE
✎
✎NOTE
The Receiver does not play sound in search
mode.
If you press the
Depending on the disc, the menu items may
differ and this menu may not be available.
or
button too quickly
this product might think you are just holding
the button down. This will lead to improper
operation. Be sure to not press these buttons
too rapidly.
Playing the Title List
z
DISC MENU
1. During playback, press the DISC
MENU or TITLE MENU button.
Skipping Chapters
TITLE MENU
POPUP
2. Press the ▲▼ buttons to select
an entry you want to play from
Title List, then press the ENTER
button.
hzZyx
During playback, press the SKIP (#$)
•
button.
If you press the SKIP ($) button, the disc
moves to the next chapter.
If you press the SKIP (#) button, the disc
moves to the beginning of the chapter. One
more press makes the disc move to the
beginning of the previous chapter.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
57
Basic Functions
Slow Motion Play/Step Motion Play
Slow Motion Play
Repeat
Off
>
hzZyx
3. To return to normal play, press the REPEAT
button again.
•
In pause ( ) mode, press the SEARCH ()
button.
If you press the SEARCH () button, the
playback speed is reduced to
* 1/8 * 1/4 * 1/2
To return to normal speed playback, press the
PLAY (► ) button.
4. Press the ▲▼ buttons to select Off, then
press the ENTER button.
✎NOTE
•
Depending on the disc, the Repeat function
may not be available.
NOTE
✎
Repeat the Section
The product does not play sound in slow
mode.
Slow motion operates only in the forward
direction.
hzZy
REPEAT
1. During playback, press the REPEAT
Step Motion Play
button on the remote control.
2. Press the ▲▼ buttons to select
hzZyx
In pause mode, press the PAUSE ( ) button.
REPEAT A-B.
•
•
Each time the PAUSE ( ) button is pressed, a
Repeat
Repeat A-B : Off
"
Mark A
>
new frame will be appear.
To return to normal speed playback, press the
PLAY ( ► ) button.
NOTE
✎
3. Press the ENTER button at the point where
The product does not play sound in step
you want repeat play to start (A).
mode.
4. Press the ENTER button at the point where
Step motion operates only in the forward
direction.
you want repeat play to stop (B).
5. To return to normal play, press the REPEAT
button again.
Repeat Playback
6. Press the ENTER button.
Repeat the Title or Chapter
NOTE
✎
If you set point (B) before 5 seconds has
elapsed, a prohibition message will appear.
Depending on the disc, the Repeat function
may not be available.
hzZy
Repeat the disc title or chapter.
REPEAT
1. During playback, press the REPEAT
button on the remote control.
2. Press the ▲▼ buttons to select
Chapter or Title, then press the
ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
58
English
Information about the primary / secondary
audio modes will be also displayed if the Blu-
ray Disc has a BONUSVIEW section.
Use the ◄► button to switch between
primary and secondary audio modes.
The languages available depend on the
languages that are encoded on the disc. This
function or certain languages may not be
available.
Using the TOOLS button
TOOLS
During playback, you can operate the
disc menu by pressing the TOOLS
button.
•
TOOLS Menu Screen
Tools
:
Title Search
1/2
Some Blu-ray Discs may allow you to select
either the multi-channel LPCM or Dolby digital
audio soundtrack in English.
Chapter Search
Time Search
Picture Settings
Audio
1/20
: 00:00:13/01:34:37
:
Normal
:
1/4 ENG Multi CH
User EQ
Subtitle
:
:
0/7 Off
Angle
1/1
Selecting the Subtitle Language
<Change
Enter
'
Return
"
hZx
NOTE
✎
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Subtitle.
Depending on the disc, the TOOLS menu
may differ.
▪
3. Press the ◄► buttons to select the desired
subtitle language.
Moving to a Desired Scene Directly
NOTE
✎
hzZy
Depending on the Blu-ray Disc / DVD, you may
be able to change the subtitle language in the
Disc Menu.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Title
Press the DISC MENU button.
Search, Chapter Search or Time Search.
The subtitle languages available depend on the
subtitle languages encoded on the disc. This
function or certain languages may not be
available on all Blu-ray Discs/DVDs.
Information about the primary / secondary
subtitle modes will also be displayed if the Blu-
ray Disc has a BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of subtitles is the sum of the
primary and secondary subtitles.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.
Selecting the Audio Language
hzZx
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Audio.
3. Press the ENTER button.
4. Press the ▲▼ buttons to select the audio
language you want.
✎NOTE
The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not
contain any BONUSVIEW audio settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
59
Basic Functions
•
User : The user can adjust the Sharpness,
Noise reduction, Contrast, Brightness,
Color, Tint function respectively.
Caption Function
x
•
•
You must have some experience with video
✎NOTE
extraction and editing in order to use this
feature properly.
If the system is connected to a BD Wise-
compliant TV that has set BD Wise to On, the
picture setting menu will not appear.
To use the caption function, save the caption
file (*.smi) with the same file name as that of the
DivX media file (*.avi) within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
Setting the BONUSVIEW
•
You can use up to 60 alphanumeric characters or 30
East Asian characters (2 byte characters such as
Korean and Chinese) for the file name.
h
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
Bonusview feature.
Changing the Camera Angle
hZ
When a Blu-ray Disc/DVD contains multiple
angles of a particular scene, you can use the
ANGLE function.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Angle.
3. Press the ◄► buttons to select the desired
Angle.
Primary a audio/video
Secondary a audio/video
Selecting the Picture Settings
hzZy
This function enables you to adjust video quality.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
1. During playback, press the TOOLS button.
3. Press the ◄► buttons to select the desired
2. Press the ▲▼ buttons to select Picture
bonusview.
Settings, then press the ENTER button.
NOTE
✎
3. Press the ◄► buttons to select the desired
Mode, then press the ENTER button.
If you switch from BONUSVIEW Video,
BONUSVIEW Audio will change automatically
in accordance with BONUSVIEW Video.
•
•
•
Dynamic : Choose this setting to increase
Sharpness.
Normal : Choose this setting for most
viewing applications.
Movie : This is the best setting for watching
movies.
Tools
BONUSVIEW Video
BONUSVIEW Audio :
Picture Settings
Off
0/1 Off
<Change
Enter
"
Download from Www.Somanuals.com. All Manuals Search And Download.
60
English
Listening to Music
ENTER button : Plays the selected track.
7
8
► button : During playback, moves to the next
page in the Music List or moves to the next track
in the Playlist.
ow
Buttons on the Remote Control
used for Music Playback
◄
button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
1
4
2
3
STOP button : Stops a track
$ button : Plays the next track.
#
button : Plays the previous track.
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts
in the Playlist, the previous track will be played.
.
9
0
5
6
SLEEP
TONE
@
7
8
9
S.DIRECT
AUDIO ASSIGN
FULL
SCREEN
1
2
REPEAT
0
!
@
!
0
3
4
NUMBER button : During the Playlist playback,
press the desired track number. The selected
track will be played.
9
8
TOOLS
INFO
5
6
7
TUNER
iPod SYNC
MO/ST
MEMORY
C
vTuner
2D ĺ 3D
SMART
SEARCH
HUB
REPEAT button : Selects the play mode in the
Playlist.
1
2
SEARCH buttons :
Audio CD (CD-DA) - Fast Play.
MP3 - Jump Play. (10 seconds)
PAUSE button : Pauses playback.
3
4
5
6
PLAY button : Plays the currently selected track.
▲▼ buttons : Selects a track in the Music List
or Playlist.
YELLOW (C) button : Select or deselect a track
in the music list.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
61
Basic Functions
Playing an Audio CD (CD-DA)/MP3 Repeat an Audio CD (CD-DA)/MP3
REPEAT
1. Insert an Audio CD (CD-DA) or an MP3 Disc
1. During the Playlist playback, press
into the disc slot.
the REPEAT button.
•
For an Audio CD (CD-DA), the first track will
2. Select the desired play mode by
be played automatically.
pressing the REPEAT button repeatedly.
•
For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
Tracks on a disc are played
in the order in which they
were recorded on the disc.
Audio CD
(CD-DA)/MP3
Off
Audio CD (CD-DA)/MP3 Screen Elements
(
) One
Audio CD
(CD-DA)/MP3
Current track is repeated.
All tracks are repeated.
Song
1
2
3
Audio CD
(CD-DA)/MP3
(
) All
Music
1/13
TRACK 001
TRACK 001
00:43
NOTE
✎
TRACK 002
03:56
During playback, press the TOOLS button and
set Shuffle Mode to On. You can play the
tracks in a random order.
TRACK 003
04:41
7
6
TRACK 004
04:02
+
00:13 / 00:43
Playlist
Audio CD
"
Enter
<
Pages
Tools
'
Return
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc slot.
5
4
•
•
For an Audio CD (CD-DA), the first track will
be played automatically.
For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
Displays the music information.
Displays the playlist.
1
2
3
4
5
6
7
Shows the current track/total tracks.
Displays buttons available.
2. To move to the Music List, press the STOP ()
or RETURN button.
The Music List screen is displayed.
3. Press the YELLOW (C) button to switch to
Shows the current play time/total play time.
Displays the current playback status.
Displays the repeated playback status.
Edit Mode.
4. Press ▲▼◄► to select a desired track, and
then press ENTER. Repeat this procedure to
select additional tracks.
•
•
The selected file will be checked.
To cancel your selection, press ENTER
again to uncheck the track.
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
62
English
Sound Mode
1/2 Page
Audio CD
| Music
Selected Items : 3
TRACK 001
TRACK 002
03:56
SFE (Sound Field Effect) MODE
00:43
TRACK 003
04:41
TRACK 004
04:02
SFE MODE
You can set the SFE mode best suited
for the type of music you are listening
to.
TRACK 005
03:43
TRACK 006
03:40
TRACK 007
04:06
TRACK 008
03:52
c
Close Edit Mode
(
)
Page
Tools
"
Select
'
Return
Press the SFE MODE button
repetatively,
STEREO HALL 1 HALL 2 J.CLUB
CHURCH ROCK CLASSIC LIVE
GAME MOVIE CONCERT STADIUM
will be selected in turn.
5. When done, press the TOOLS button.
6. To play the selected track(s), select Play
Selected in the Tools menu, and then press
ENTER.
Dolby Pro Logic II Mode
Music
1/3
You can select the desired Dolby Pro
Logic II audio mode.
TRACK 001
TRACK 001
00:43
TRACK 002
03:56
Press the
PL II button.
TRACK 003
04:41
Setting the speakers with PL IIz
+
00:13 / 00:43
1. Set the 7.1CH Connection settings to "PL
Audio CD
"
Enter
Tools
'
Return
IIz". (For further details, refer to page 41.)
2. Press the
PL II button of the remote
7. To return to the Edit Mode, press STOP or
control until "HEIGHT” or “PL OFF”
appears on the display. Set to “HEIGHT”
to enable sound reproduction from front
center/height speakers.
RETURN.
8. To exit Edit Mode, press the YELLOW (C)
button.
NOTE
✎
You can listen to a 2CH sound source
in 7.1CH surround sound with all
You can create a playlist with up to 99 tracks
on Audio CD (CD-DA).
speakers active.
HEIGHT
- A specific speaker(s) may not be
output depending on the input
signal.
Select this option to listen through the
PL OFF
front left/right speakers and the
subwoofer only.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
63
Basic Functions
The models below support audio sync
settings. Press iPod SYNC on the remote
control to change audio delay.
Supported Models : classic/3G nano/4G
nano/120GB classic/160GB Classic/5G nano
Setting the speakers with DPL IIx
1. Set the 7.1CH Connection settings to
"Surround Back". (For further details, refer to
page 41.)
2. Press the
PL II button of the remote
control until the desired setting is
3D Sound
displayed. Once selected with the desired
mode, sound will be heard through the
surround speakers.
You can enjoy more natural and vivid
surround sound with enriched tones by
adjusting the depth of sound using the
level options.
3D SOUND OFF 3D SOUND HIGH
3D SOUND MEDIUM 3D SOUND LOW
Adds realism to the movie
soundtrack.
MOVIE
When listening to music, you can
✎NOTE
experience sound effects as if you
MUSIC
3D Sound is not available in FM mode.
are listening to the actual
performance.
Using the SHIFT button
GAME
You can hear like game sound.
You will hear multi channel
surround sound.
MATRIX
ENTER, ▲▼◄►, S.DIRECT, TONE, SLEEP
and AUDIO ASSIGN button will operate, after
pressing the SHIFT button.
You can listen to a 2CH sound
source in 5.1CH surround sound
with all speakers active.
✎NOTE
PL
- A specific speaker(s) may not be
output depending on the input
signal.
ENTER, ▲▼, and ◄► buttons are active
even when you don't press the SHIFT button.
PL OFF
PL mode will be off.
TONE
After pressing the SHIFT button, and
then Press the TONE button repeatedly
to select the option you want.
You can adjust the each value by
pressing the ▲▼ buttons.
iPod SYNC
9
If you insert your iPod player into the
iPod Dock that has already been
connected to the system, you can play
the video files in your iPod player
through the connected TV.
B
•
•
•
BASS : -6dB ~ +6dB
TREBLE : -6dB ~ +6dB
TONE : ON, OFF
If the video signal does not synchronize properly
with the audio signal, press iPod SYNC on the
remote control to correct the synchronization.
✎NOTE
The Tone Control function can be applied to
all channels except for the subwoofer.
If it is set to Tone Off, the Tone Control
function will be disabled.
✎NOTE
Before you can play the video files in the iPod
player, you must connect the Audio/Video
terminals of the TV to the home theater using the
Composite (A/V) cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
64
English
AUDIO ASSIGN
You can listen to sound in 2 channel
analog , Dolby Digital or DTS using this
unit.
Playing back a Picture
G
0
Viewing Photo Files
Each time you press this button, the
input mode changes as follows:
1. Connect a USB memory that contains JPEG
files or insert a disc that contains JPEG files.
2. Press the ◄► buttons to select My
Contents, and then press the ▲▼ buttons
to select Photos, and then press the ENTER
button.
3. Press the ▲▼◄► buttons to select the
folder you want to play, and then press the
ENTER button.
4. Press the ▲▼◄► buttons to select the
photo you want to play, and then press the
ENTER button.
For SAT function
SAT HDMI1 SAT OPTIC1 SAT ANALOG
For GAME function
GAME HDMI2 GAME OPTIC2 GAME
ANALOG
For TV function
TV OPTIC3(TV ARC) TV ANALOG
For CD function
NOTE
✎
You can't enlarge PG graphic in the full screen
mode.
CD COAXIAL CD ANALOG
For AUX1 function
Using the TOOLS button
TOOLS
During the slide show playback, you
can use various function by pressing
the TOOLS button.
AUX1 HDMI3 AUX1 ANALOG
✎NOTE
You can also change the input mode by
pressing the AUDIO ASSIGN button on the
front of your Receiver.
Tools
Pause Slide Show
Slide Show Speed
Slide Show Effect
Background Music
:
:
:
Normal
Blind
Off
You can enjoy Dolby Digital or DTS if you
connect the digital audio output jack of an
external audio component to the optical or
coaxial digital audio input jack on the main
unit.
Background Music Setting
Zoom
Rotate
Picture Settings
Information
For the TV function, the TV ARC menu will
be displayed only if an ARC-compliant TV is
connected.
"
Enter
'
Return
•
•
•
•
Pause Slide Show : Select to pause the slide
S.DIRECT
Output the original signal as it is without
applying the sound field effect or any
other sound effect.
show.
Slide Show Speed : Select to adjust the slide
show speed.
Slide Show Effect : Select to set the slide
show effects.
Background Music : Select to listen to music
while viewing a slide show.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
65
Basic Functions
•
•
•
Background Music Setting : Select to set the
My Contents
background music.
Videos
Zoom : Select to enlarge the current picture.
(Enlarge up to 4 times)
Rotate : Select to rotate the picture. (Rotate
the picture either clockwise or counter
clockwise.)
Connected Device
USB
M
Settings
Function
"
Enter
'
Return
•
•
Picture Settings : Select to adjust the picture
quality.
c
Safely Remove USB
d
WPS(PBC)
Information : Shows the picture information
including the name and size, etc.
3. Press the ENTER button.
4. Press the ▲▼◄► buttons to select
Videos, Music or Photos, and then press the
ENTER button.
NOTE
✎
If the system is connected to a BD Wise
compliant TV that has set BD Wise to On, the
Picture settings menu will not appear.
5. For playing back Video, Music or Photo files,
refer to pages 56~66.
Before you can enable the background music
function, the photo file should exist in the same
storage media with the music file. However,
the sound quality can be affected by the bit
rate of the MP3 file, the size of the photo and
the encoding method.
NOTE
✎
You must remove the USB storage device safely
(by performing the “Safely Remove USB” function)
to prevent possible damage to the USB memory.
Press the MENU button to move to the home
menu, select the YELLOW (C) button, and then
press the ENTER button.
If you insert a disc when playing files on a USB
storage device, the device mode changes to
“BD/DVD” automatically.
Playing back a USB Storage Device
F
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
1. Move to the home menu.
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
d
WPS(PBC)
2. In Stop mode, connect the USB storage
device to the USB port on the front panel of
the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
66
English
Using buttons on the Main Unit
Listening to Radio
1. Using the INPUT SELECT dial on the front panel
to select FM.
Using buttons on the Remote Control
2. Tune in to the desired station.
1. Press the INPUT SELECT on the remote control
to select FM.
2. Tune in to the desired station.
•
Preset Tuning 1 : You must first add a desired
frequency as a preset. Press the STOP () or
TURNING MODE button to select PRESET
•
Preset Tuning 1 : You must first add a desired
frequency as a preset. Press the STOP ()
button to select PRESET and then press the
and then press the SELECT
(
)
button to
select the preset station.
•
•
Manual Tuning : Press the STOP () or
TUNING/CH (
) button to select the preset
TURNING MODE button to select MANUAL
station.
and then press the SELECT
(
)
button to
•
•
Manual Tuning : Press the STOP () button to
tune in to a lower or higher frequency.
select MANUAL and then press the TUNING/
CH ( ) button to tune in to a lower or higher
frequency.
Automatic Tuning : Press the STOP () or
TURNING MODE button to select MANUAL
and then press and hold the SELECT
(
)
Automatic Tuning : Press the STOP () button
button to automatically search the band.
to select MANUAL and then press and hold the
TUNING/CH (
search the band.
) button to automatically
Presetting Stations
Example : Presetting FM 89.10 into memory
1. Using the INPUT SELECT dial on the front panel
Presetting Stations
Example : Presetting FM 89.10 into memory
to select FM.
2. Press the SELECT
(
)
button to select
1. Press the INPUT SELECT on the remote control
<89.10>.
to select FM.
3. Press the MEMORY button.
NUMBER flashes on the display.
4. Press the MEMORY button again.
TUNING/CH
2. Press the
(
)
button to select
•
<89.10>.
TUNER
3. Press the TUNER MEMORY button.
NUMBER flashes on the display.
4. Press the TUNER MEMORY button
MEMORY
C
•
Press the MEMORY button before NUMBER
disappears from the display.
•
•
NUMBER disappears from the display and the
station is stored in memory.
again.
•
Press the TUNER MEMORY button
before NUMBER disappears from the display.
NUMBER disappears from the display and the
station is stored in memory.
5. To preset another station, repeat steps 2 to 4.
To tune in to a preset station, press the
SELECT button to select a channel.
•
•
(
)
5. To preset another station, repeat steps 2 to 4.
To tune in to a preset station, press the
TUNING/CH ( ) button to select a channel.
•
Setting Mono/Stereo
Press the MO/ST button.
•
Each time the button is pressed, the
sound switches between STEREO and
MONO.
•
In a poor reception area, select MONO for a
clear, interference-free broadcast.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
67
Basic Functions
Connecting an iPod/iPhone Using the
USB Cable
Playing Music
If the Receiver is connected to an iPod/iPhone using
the provided USB cable, you can play music in
iPod/iPhone through the Receiver.
My Contents
Videos
Connected Device
iPod
L
M
Settings
ASC MIC
VIDEO
AUDIO
PHONES
AUDIO
ASSIGN
AUDIO
EFFECT
Function
MENU
RETURN
3D SOUND
"
Enter
'
Return
AUX
1
IN
d
WPS(PBC)
1. Connect the iPod dock connector to the iPod
Jack on the rear panel of the product.
1. Connect an iPod/iPhone using the USB
2. Place the iPod in the supplied iPod Dock.
cable to the front USB port.
•
•
Your iPod automatically turns on.
•
•
Your iPod is automatically turned on.
The “iPod” message appears on the TV
The “iPod” message appears on the TV
screen.
screen.
3. Press the ENTER button.
2. Press the ENTER button.
3. Select the music file to play.
4. Press the ◄▲▼ buttons to select Music,
and then press the ENTER button.
-
You can use the remote control or the
5. Select the music file to play.
product to control simple playback functions
- You can use the remote control or product
to control simple playback functions such
as the PLAY, PAUSE, STOP, #/ $, /
and REPEAT buttons. See page 19.
such as the PLAY, PAUSE, STOP,
#
/$
and /buttons. (See page 19.)
✎NOTE
If you want to return to the iPod menus while the
iPod player is connected using the USB cable,
press INPUT SELECT on the remote control or
using the INPUT SELECT dial on the front panel
and select R-IPOD. The FUNCTION mode
switches as follows: BD/DVD ꢀ SAT ꢀ GAME ꢀ
AUX1 ꢀ AUX2 ꢀ CD ꢀ R-IPOD ꢀ FM ꢀ TV
✎NOTE
Adjust the volume to a moderate level before
you connect your iPod to the product.
When the product is on and you connect an
iPod, the product will charge the iPod's
battery.
Make sure to connect the dock connector
so that the label “” faces upward.
Connecting an iPod/iPhone Using the Dock
Watching a Movie
If the Receiver is connected to the iPod/iPhone
specific dock, you can play videos or music in an
iPod/iPhone through the Receiver.
You can play video files stored in the iPod player
by connecting it to the product.
1. Connect the iPod dock connector to the iPod
LAN
iPod
HDMI OUT
ARC
(MONITOR)
HDMI
1
Jack on the rear panel of the product.
(SAT)
iPod
2. In the iPod screen, move to Videos >
Settings, then set the TV Out option and the
TV signal.
VIDEO IN
VIDEO OUT
COMPONE
1
SAT
GAME
TV
MONITOR
(SAT)
(GA
Y
P
B/CB
3. Place the iPod in the supplied iPod Dock.
P
R/CR
SAT
GAME
TV
CD
AUDIO IN
IN
FM ANT
•
The “iPod” message appears on the TV
screen.
4. Press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
68
English
5. Press the ◄▲▼ buttons to select Video, and
✎NOTE
then press the ENTER button.
“Made for iPod” means
6. Select the video file to play.
that an electronic
-
You can use the remote control or the
accessory has been
product to control simple playback functions
designed to connect specifically to iPods
and has been certified by the developer to
meet Apple performance standards.
such as the PLAY, PAUSE, STOP,
#
/$
and /buttons. (See page 19.)
“Made for iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhones and has been certified
by the developer to meet Apple
✎
NOTE
You must have the VIDEO output
(Composite) connected to your TV to view
iPod video.
If you want to play iPod video via VIDEO
output, set Anynet+ (HDMI-CEC) to off.
No screen but the playback screen will
appear on the TV. View other iPod screens
on the iPod player.
If the connected iPod does not support
video playback, the "Playing video files is not
supported on this iPod model." message
appears when you select the Video menu.
If you want to return to the iPod menus while
the iPod player is connected using the dock,
press INPUT SELECT on the remote
control or press INPUT SELECT on the front
panel of the system and select R-IPOD. The
FUNCTION mode switches as follows :
BD/DVD ꢀ SAT ꢀ GAME ꢀ AUX1 ꢀ AUX2 ꢀ CD
ꢀ R-IPOD ꢀ FM ꢀ TV
performance standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
The volume control may not operate
normally with iPod and iPhone models not
listed above. If you have a problem with any
of the models listed above, please update
the software of the iPod/iPhone to the
lastest version.
Depending on the software version of the
iPod, control problems may occur. This is
not a malfunction of the product.
Depending on the software version or the
type of the iPod, some operations may
differ. Install the latest iPod software.
(recommended)
Some actions like iPod SYNC may depend
on video sources or the iPod model you
have.
You can enjoy music or videos through the
BD/DVD function and enjoy music, videos or
photos through the Remote iPod function.
You need to use iPod Dock to enjoy videos
or photos.
iPod/iPhone Models You Can Use with
This Product
iPod touch (3rd generation)
iPod touch (2nd generation)
iPod touch (1st generation)
iPod classic
iPod with video
iPod with dock connector
iPod with Click Wheel
Playback of applications' contents through
the product is not guaranteed. We
recommend playing contents downloaded
to the iPod.
iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)
If you have a problem using your iPod,
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
Download from Www.Somanuals.com. All Manuals Search And Download.
English
69
Network Services
You can enjoy various network services such as
Smart Hub or BD-LIVE by connecting the
product to your network.
3. The Smart Hub screen appears.
✎NOTE
Certain applications are available only in certain
countries.
Read the following instructions before using
any network service.
1. Connect the product to the network.
4. The Terms of Service Agreement screen
appears.
(see pages 32~33)
If you want to agree, press the ◄► buttons to
select Agree, then press the ENTER button.
2. Configure the network settings.
(see pages 47~50)
✎NOTE
Screens can take a few seconds to appear.
Using Smart Hub
5. The Service Update screen appears and
installs a number of services and applications.
When done, it closes. The applications and
services downloaded are displayed on the
Smart Hub screen. This may take some time.
Using Smart Hub, you can stream movies,
videos, and music from the Internet, access
various for pay or free-of-charge applications and
view them on your TV. Application content
includes news, sports, weather forecasts, stock
market quotes, maps, photos, and games.
✎NOTE
Smart Hub may close momentarily during the
installation process.
You can also start this function by
pressing the SMART HUB button
on the remote control.
A number of screens may appear after
installation. You can press the ENTER button
to close them or let them close on their own.
Starting Smart Hub the First Time
6. To start an application, press the ▲▼◄►
buttons to highlight a widget, then press the
ENTER button.
To start Smart Hub for the first time, follow these
steps :
1. Go to the Home menu.
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
c
Safely Remove USB
d
WPS(PBC)
2. Press the ◄► buttons to select Internet,
and press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
70
English
Smart Hub at a Glance
Navigation Help : Displays the remote control
buttons you can use to navigate in Smart Hub.
1
2
3
4
5
•
•
•
•
RED (A) : To log in to Smart Hub.
GREEN (B) : To sort the applications.
YELLOW (C) : To edit the applications.
BLUE (D) : To change the settings of Smart
Hub.
Search
6
7
Your Video
Samsung Apps
Contents
1
Contents
2
Contents
3
Contents
4
Recommended
Contents
1
Contents
2
Contents
3
Contents
4
Contents
5
Contents
6
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
My Applications : Displays your personal gallery
of applications which you can add to, modify, and
delete.
Contents
1
Contents
2
Contents
3
Contents
4
Contents
5
Contents
6
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
Contents
7
Contents
8
Contents
9
Contents 10
Contents 11
Contents 12
Contents 13
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
a
Login
b
Sort by
c
Edit Mode
d
Settings
✎NOTE
Samsung Electronics takes no legal
7
6
responsibility for any interruption of the Smart
Hub service caused by the service provider for
any reason.
Commercial : Displays the Smart Hub Guide,
an introduction to the product, and new
application introductions.
1
The Smart Hub service downloads and
processes data via the Internet so that you can
enjoy the Internet contents on your TV screen.
If the Internet connection is unstable, the
service may be delayed or interrupted.
Furthermore, the product may turn off
automatically in response to conditions on the
Internet.
Your Video : Provides recommendations for
videos based on your tastes.
Lets you see movie recommendations
based on your previous preferences.
Lets you select a movie, displays a list of
VOD (Video on Demand) providers that
have the movie, and then lets you choose
a provider for streaming. (Streaming is
unavailable in some areas.)
•
•
2
If this occurs, check the Internet connection
and try again.
Application services may be provided in
English only and the contents available may
vary, depending on your area.
For more information about a Smart Hub
service, visit the web site of the applicable
service provider.
The services provided are subject to change
by the Smart Hub service provider without
notice.
The Smart Hub service contents may differ
depending on the product’s firmware version.
•
For instructions to use Your Video, please
Search : Provides an integrated search of
your video providers and connected AllShare
devices.
•
•
•
Usable while using Smart Hub (except
when you are watching a Blu-ray Disc).
For easy access, use the SEARCH button
on the remote control.
For instructions to use search function,
3
For pay DivX contents with copy protection
can only be played through a composite, a
component or an HDMI cable.
Samsung Apps : You can download various for
pay or free-of-charge application services.
4
5
Recommended : Displays recommended
contents managed by Samsung.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
71
Network Services
Using the Keypad
Creating an Account
Through your remote, you can use the On-
Screen Keypad to enter letters, numbers, and
symbols.
To establish your own, exclusive, configuration of
Smart Hub, create your own Smart TV Account.
To create an account, follow these steps:
1. Press the RED (A) button on your remote
1
2
3
control. The Login screen appears.
. , –
abc
def
4
5
6
1
ghi
jkl
mno
7
8
9
pqrs
tuv
wxyz
Login
0
Smart TV ID
Password
Press [ENTER]
%
2
3
6
Shift
Delete
Press [ENTER]
T9
Remember my Smart TV ID and password
ab Ab AB
1
Login
Cancel
b
Input Method
/
Language: English
Create Account
Find Password
4
5
2. Press the ▲▼◄► buttons to select Create
Account, and then press the ENTER
button.
The current keypad.
1
2
Use to enter letters, numbers, and symbols.
Press the FULL SCREEN button on the remote
control to shift the input mode.
: ab, Ab, AB, numbers or icons.
3. On the next screen, select Smart TV ID, and
then press the ENTER button. An entry
screen and keypad appear.
Displays the current input mode.
3
4
4. Use the keypad to enter your e-mail
address. This will serve as your ID.
Press the GREEN (B) button on the remote
control to change the input method. (T9 or ABC)
NOTE
✎
Press the TOOLS button on the remote control
to change the language.
The keypad works like the keypad on a cell
phone.
5
6
Press the REPEAT button on the remote control
to delete a character.
5. When done, press the ENTER button to
select OK, and then press the ENTER
button again. The Create Account screen re-
appears.
Entering Text, Numbers and Symbols
To enter text, press the number button on the
remote that corresponds to the letter you want to
enter. Press the button rapidly to enter a letter
that is not the first letter listed on the On-Screen
keypad button. For example, if you want to enter
the letter b, press the 2 button on your remote
rapidly twice. To enter the first letter listed on a
button, press, release, and then wait.
To move within the text, use the Arrow buttons.
To delete text, move the cursor to the right of the
character you want to delete, and then press the
REPEAT button. To change case or enter
numbers or punctuation, press the FULL
SCREEN button.
6. Select Password, and then press the
ENTER button. The Password screen and a
keypad appear.
7. Use the keypad to enter a password.
The password can be any combination of
letters, numbers, and symbols.
NOTE
✎
Press the RED (A) button on your remote to
show or hide the password as you enter it.
Download from Www.Somanuals.com. All Manuals Search And Download.
72
English
8. When done, press the ENTER button to
select OK, and then press the ENTER
button again. The Create Account screen
re-appears.
2. Select the Down Arrow next to the Smart
TV ID field, and then press the ENTER
button.
3. Select your ID from the list that appears, and
then press the ENTER button. The Login
screen re-appears.
9. Select Confirm password, and then press
the ENTER button.
10. Repeat Steps 7 and 8.
4. Select Password, and then press the
ENTER button. The Password window and
a keypad appears.
11. When the Create Account screen re-
appears, select Create Account, and then
press the ENTER button. The Confirmation
window appears.
5. Using the keypad and your remote, enter
your password. When done, press the
ENTER button, select OK, and then press
the ENTER button again.
12. Select OK, and then press the ENTER
button. The Continue to Register Service
window appears.
NOTE
✎
13. Select Connect Service, and then press the
If you want Smart Hub to enter your password
automatically, select Remember my Smart TV
ID and password after you have entered your
password, and then press the ENTER button.
A check appears. Smart Hub will now enter
your password automatically when you select
or enter your ID.
ENTER button.
14. The Register Service Account Window
appears. If you want to register, Select Go
Register and then press the ENTER button.
•
•
If you have existing accounts with any of
the listed providers, you can associate the
provider account and the provider account
password with your Smart TV Account.
Registration makes it easier to access
the providers web site. For registration
instructions, go to Step 2 in Account
Management under the Settings Menu.
If you don’t have existing provider accounts
or do not want to register existing accounts
at this time, select Register Later, and then
press the ENTER button. You can also let the
window close on its own in about a minute.
The Settings Menu - BLUE (D)
The Settings Menu Screen gives you access to
account management, account reset, and
account properties functions.
To access the Settings Menu, and then select a
menu item, follow these steps:
1. Press the BLUE (D) button on your remote.
2. Press the ▲▼ to select a menu item, and
then press the ENTER button.
NOTE
✎
The functions on the Settings Menu screen are
described below.
You must use an e-mail address as an ID.
You can register up to 10 User Accounts.
You do not need an account to use Smart
Hub.
NOTE
✎
The Service Manager item listed in the Settings
Menu is not available for Blu-ray Home
Theaters.
Account Log In
To log in to your Smart TV Account, follow these
steps:
Account Management
The Account Management Menu contains
functions that let you register your service
provider accounts, change your Smart Hub
password, and delete or deactivate your Smart
TV Account.
1. With the Smart Hub main screen displayed
on your TV, press the RED (A) button on
your remote. The Login screen appears.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
73
Network Services
Register Service Account
Change Password
If you have existing accounts with any of the
providers listed by the Register Service Account
function, you can associate the provider account
and the provider account password with your
Smart TV Account. If you associate the account,
you will be able to log onto the account through
Smart Hub easily, without entering your account
name or password.
The Change Password function lets you change
your Smart Hub password. To change the
password, follow these steps:
1. Select Change Password, and then press
the ENTER button.
2. Enter your current password. The next
screen appears.
3. On the next screen, enter a new password
on the first line. Enter it again on the second
line to confirm.
To use the Account Management function, follow
these steps:
1. In the Account Management menu, select
Register Service Account, and then press
the ENTER button. The Register Service
Account Window appears.
4. The Changing Password Complete message
screen appears. Press the ENTER button or
wait for the screen to close - about 5
seconds.
2. Press the ▲▼ arrow buttons to select a
Service Provider you want to associate with
your Smart TV Account, and then press the
ENTER button.
Remove from TV Account List
The Remove from TV Account List function
cancels all your current registered Service
Accounts that you registered on the Register
Service Account screen.
NOTE
✎
If you have a Samsung account and you want
to use the Samsung Apps function in Smart
Hub, you must register your Samsung Apps
account here. See page 77 for more
information.
Deactivate Account
The Deactivate Account function deactivates your
Smart TV Account and deletes it and all your
account settings entirely from Smart Hub.
3. Using your remote and the on-screen
Keypad, enter your site ID and password.
When done, press the ENTER button.
Reset
The Reset function initializes all downloaded
widgets, erases all user accounts and settings
from the product, and resets all Smart Hub
settings to the factory default settings. It then
restarts Smart Hub as if it were starting for the
first time. Your account, however, remains on the
Smart Hub server. To log into your account, enter
your ID and password on the Create Account
screen.
NOTE
✎
This is the ID and password you normally use
to access your account on this site.
4. If you have entered the ID and password
correctly, the Registered Successfully
message appears.
5. If you pressed OK, repeat Steps 2 through 4
To use the Reset function, follow these steps:
to associate another Service Provider.
1. In the Account Management menu, select
Reset, and then press the ENTER button.
The Reset screen appears.
6. When you are done, press the RETURN
button.
2. Enter the your Security password. This is the
password you entered if you set up a BD or
DVD Parental rating (See page 52). If you did
not, enter 0000.
Download from Www.Somanuals.com. All Manuals Search And Download.
74
English
3. After a few moments, Smart Hub
automatically resets. The screen may go
black, then Smart Hub re-appears. In a few
moments, it starts the re-initialization
procedure.
The functions in the Edit Mode Menu bar are
described below.
NOTE
✎
Some menu items may not appear on the
screen. To see these items, press the ◄► to
move to the screen edge, and then press one
more time to reveal the items.
4. To complete the re-initialization, go to Step 4
in Starting Smart Hub for the First Time. (See
page 70)
You can close the bar by highlighting the X on
the bottom right side, and then pressing the
ENTER button.
NOTE
✎
If you forgot your password, press the STOP
) button on the front panel of the product
for more than 5 seconds with no disc inserted.
(
I
Move
The Move function lets you change the screen
position of a widget. To use the Move function,
follow these steps:
Properties
The Properties menu item lists three functions
that display information about Smart Hub :
1. Press the YELLOW (C) button on your
remote.
Detail
2. Select a widget, and then press the ENTER
Lists information about Smart Hub including
version number, the number of services installed,
memory usage, and the unique product ID.
button. A check appears above the widget.
3. Press the ▲▼◄► to select Change
Position, and then press the ENTER button.
A position change icon appears above the
widget.
Terms of Service Agreement
Displays the Terms of Service Agreement.
4. Press the ▲▼◄► to move the icon. Press
the ENTER button when the icon is in the
position of your choice. The widget moves to
its new location.
The Edit Mode Menu - YELLOW (C)
The functions in the Edit Mode menu let you
manipulate the widgets in the My Applications
section of the Smart Hub screen. Using these
functions, you can lock and unlock access to
some widgets, New Folder and move widgets to
them, rename folders, delete widgets, and
change the position of widgets on the screen.
New Folder
The New Folder function lets you create and
name new folders. Once you have created a
folder, you can move widgets into it. To use the
New Folder function, follow these steps:
To access the Edit Mode Menu, and then select
a menu item, follow these steps:
1. Press the YELLOW (C) button on your
remote.
1. Press the YELLOW (C) button on your
remote. The Edit Mode menu bar appears
on the bottom of the screen.
2. Press the ▲▼◄► to move the cursor to
New Folder, and then press the ENTER
button. The New Folder window and a
keypad appear.
2. Press the ▲▼◄► to select a menu item,
and then press the ENTER button.
3. Use the keypad to enter the name of the
folder, and then press the ENTER button.
The New Folder screen closes and the New
Folder appears on the Smart Hub screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
75
Network Services
Move to Folder
Rename Folder
The Move to Folder function lets you move a
widget to a folder. To use the Move to Folder
function, follow these steps:
The Rename Folder function lets you rename
folders. To use the Rename Folder function,
follow these steps:
1. Press the YELLOW (C) button on your
1. Press the YELLOW (C) button on your
remote.
remote.
2. Select a widget, and then press the ENTER
2. Press the ▲▼◄► to select a folder, and
button.
then press the ENTER button.
3. Press the ▲▼◄► to select Move to Folder,
and then press the ENTER button. The
Move to Folder window opens.
3. Press the ▲▼◄► to select Rename a
Folder, and then press the ENTER button.
The Folder Rename window and a keyboard
appears.
4. Press the ▲▼◄► to select a folder, and
then press the ENTER button. The Moved to 4. Use the key board to enter a new name, and
Folder message appears, and then closes.
The widget has been moved to the folder.
then press the ENTER button. The Rename
window closes and the new name appears
below the folder.
To Access Widgets in a Folder
Lock
1. Close the Edit Mode menu.
The Lock function lets you lock some widgets in
My Applications so they can not be opened
without entering the Parental Security Code.
2. In My Applications, press the ▲▼◄► to
select a folder, and then press the ENTER
button. The folder opens.
To use the Lock function, follow these steps:
3. Select a widget, and then press the ENTER
button. The widget’s application or service
starts.
1. Press the YELLOW (C) button on your
remote.
2. Press the ▲▼◄► to select a widget, and
then press the ENTER button. If the widget
can be locked, the Lock menu item is
enabled.
To Edit Items in a Folder
Select a folder, and then press the ENTER
button. The folder opens.
Press the YELLOW (C) button on your remote.
The Edit buttons appear at the bottom of the
screen.
These buttons work the same as the Edit Mode
menu buttons on the main screen. For example,
to move a widget back to the My Applications
main screen:
3. Press the ▲▼◄► to select Lock, and then
press the ENTER button. The Security
window appears.
4. Enter your Parental Security Code (See page
52). If you have not created a Parental
Security Code, enter 0000.
5. Press the ENTER button. The Lock Service
window appears confirming the lock, and
then closes. A lock symbol appears next to
the widget.
1. Select the widget.
2. Select Move to Folder, and then press the
ENTER button. The Move to Folder window
appears.
3. Select My Applications, and then press the
ENTER button. The Move to Folder window
closes and the widget returns to the main
My Applications screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
76
English
Unlock
Samsung Apps
1. Press the YELLOW (C) button on your
Samsung Apps lets you download for pay or
free-of-charge applications and services to your
Blu-ray Home Theater and view or use them on
your TV.
remote.
2. Press the ▲▼◄► to select a locked
widget, and then press the ENTER button.
These applications and services include videos,
music, photos, games, news, sports, etc.
Widgets for the new apps appear in My
Applications.
Additional applications and services are added
regularly.
3. Press the ▲▼◄► to select Unlock, and
then press the ENTER button. The Security
window appears.
4. Enter the Parental Security Code (See page
52). If you have not created a Parental
Security Code, enter 0000.
5. Press the ENTER button. The Lock Service
Released window appears confirming the
lock has been release, and then closes.
For Pay Apps
To download for pay apps, you need to create a
Samsung Account and add a credit card to the
account.
Delete
The Delete function lets you delete widgets from
My Applications. To use the Delete function,
follow these steps:
To create a Samsung account, please visit www.
samsung.com
NOTE
✎
1. Press the YELLOW (C) button on your
This service may not provided in some
countries.
remote.
2. Press the ▲▼◄► to select a widget, and
then press the ENTER button.
Accessing the Samsung Apps Screen
3. Press the ▲▼◄► to select Delete, and
then press the ENTER button. The
message, "Do you want to delete selected
item(s)?" appears.
To access Samsung Apps, press the ▲▼◄►
buttons to navigate to the Samsung Apps area
on the Smart Hub main screen, and then press
the ENTER button. The Samsung Apps screen
appears.
4. Select Yes, and then press the ENTER
button. The widget is deleted.
NOTE
✎
The Sort by Menu - GREEN (B)
If this is the first time you are accessing this
screen, the terms of service window appears.
Select Agree, and then press the ENTER
button.
The functions in the Sort Menu let you sort the
widgets in My Applications by Name, Date,
Frequency (of use), and Category. If you manually
change the position of a widget, the Sort Menu
automatically highlights User Defined when you
start it.
To sort the widgets in My Applications, follow
these steps:
1. Press the GREEN (B) button on your remote.
2. Press the ◄► to select a sorting method,
and then press the ENTER button. Smart
Hub sorts the widgets by the method you
have chosen.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
77
Network Services
Using the Samsung Apps Screen
Samsung Apps by category
To use the Samsung Apps screen, follow these
steps:
The following categories are available:
•
•
•
•
What’s New? : Displays newly registered
applications.
1. Press the ◄► buttons to move to the
Video : Displays various video media such as
movies, TV shows, and short length videos.
Game : Displays various games such as sudoku
and chess.
Sports : Displays various sports media services
such as match information, images, and short
length videos.
category list on the left.
2. Press the ▲▼ to highlight a category. In a
few seconds, the Samsung Apps screen
displays the applications in that category.
The Sort tabs appear across the top.
3. Press the ► button to move to the displayed
applications or services.
•
Lifestyle : Includes various lifestyle media services
such as music, personal photo management
tools, and social networking such as Facebook
and Twitter.
4. Press the ▲▼◄► buttons to select an
application or service, and then press the
ENTER button. The Application Details
screen appears describing the service or
application.
5. Select Download Now, and then press the
ENTER button. If the application or service is
free, it downloads and runs. If not, and there
is a fee, follow the directions on the screen
to complete the download.
•
•
Information : Includes various information services
such as news, stocks, and weather.
Other : Includes other miscellaneous services.
My Account
My Account gives you access to your Samsung
Apps order and download history, and to the My
Apps Cash screen. You must have a Samsung
account to access this information.
NOTE
✎
Some apps are free to download, but require
registration with the provider or a paid account
with the provider to use.
Widgets for applications and services you have
downloaded from Samsung Apps appear in
My Applications.
Help
If you have questions about Samsung Apps,
check Help first. If none of the tips apply, please
Sort By Tabs
To use the Help function, follow these steps:
You can access the Sort By tabs on the top of
the screen using the ▲▼◄► buttons. Each tab
displays the services or applications in the
category you chose, sorted by the criteria on the
tab (Recommended, Most Downloaded, Most
Recent, Name).
1. Press the ▲▼◄► buttons to select Help,
and then press the ENTER button.
2. Press the ◄► to enter Help after it appears.
3. Press the ▲▼ to scroll the Help text.
4. Press the ◄ to exit Help.
You can also use the BLUE (D) button on your
remote to access the Sort By tabs. Each time
you press the BLUE (D) button, you change the
display from one sort tab to the next.
Download from Www.Somanuals.com. All Manuals Search And Download.
78
English
Using the colored buttons on your
remote with Samsung Apps
Using the AllShare Function
AllShare lets you play music, video, and photo files
located in your PC or your DLNA compatible mobile
phone or NAS on the product.
To use AllShare with your product, you must
connect the product to your network (See pages
32~33).
To use AllShare with your PC, you must install
AllShare software on your PC.
If you have a DLNA compatible mobile phone or
NAS, you can use AllShare without any additional
software.
You can download the PC software and get detailed
instructions for using AllShare from the Samsung.
com web site.
•
•
•
RED (A) (Login) : To log into your Smart TV
Account.
GREEN (B) (Thumbnail/List View) : To toggle
applications between Thumbnail and List view.
BLUE (D) (Sort By) : To sort the applications in a
category by Recommended, Most Downloaded,
Most Recent, or Name.
•
Return : To return to the previous menu.
NOTE
✎
The Internet contents services may be added
or deleted by providers without notice.
For instructions to use Your Video or Search
Using vTuner Function
vTuner is the fuction of the listening a
radio. If you press the vTuner button,
you can move to vTuner widget.
Press the vTuner button.
NOTE
✎
You can use the vTuner Function after download
the vTuner widget from Samung Apps.
BD-LIVE™
Once the product is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1. Attach a USB memory stick to the USB jack
on the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2. Insert a Blu-ray disc that supports BD-LIVE.
3. Select an item from various BD-LIVE service
contents provided by the disc manufacturer.
NOTE
✎
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
79
Other Information
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instructions below do not help, turn off the product,
disconnect the power cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864).
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
The iPod fails to connect.
Playback does not start.
• Check the condition of the iPod connector and Dock.
• Keep the iPod software version up to date.
• Check the region number of the BD/DVD.
BD/DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
•
•
The Receiver does not play sound during fast playback, slow playback,and step motion
playback.
Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only from a
few speakers and not all 8.
• On certain BD/DVD discs, sound is output from the front speakers only.
• Check if the speakers are connected properly.
• Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
Select "3D SOUND, NEO:6, PRO LOGIC II" to use all peakers.
The sound from the left/right
channels is reversed.
• Are the left/right speaker or left/right input/output cables connected properly?
• Check the left/right channel and connect it/them correctly.
Dolby Digital 7.1 CH Surround
Sound is not produced.
•
Is there "Dolby Digital 7.1 CH" mark on the disc? Dolby Digital 7.1 CH Surround Sound is
produced only if the disc is recorded with 7.1 channel sound.
• Is the audio language correctly set to Dolby Digital 7.1-CH in the information
display?
The remote control does not work.
• Are you operating the remote within its operational range and within the proper angle
relative to the sensor?
• Are the batteries drained?
• Have you selected the mode (BD-RX, TV, SHIFT) functions of the remote control (BD-RX,
TV, SHIFT) correctly?
• Disc is rotating but no
picture is produced.
• Picture quality is poor and
picture is shaking.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
Audio language and subtitles do
not work.
•
Audio language and subtitles will not work if the disc does not contain them.
Download from Www.Somanuals.com. All Manuals Search And Download.
80
English
Symptom
Check/Remedy
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
Aspect ratio cannot be changed.
• You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3
Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working.
(Example: The power goes out
or a strange noise is heard.)
• Press and hold the romote control's STOP ( I ) button for 5 seconds in
STANDBY mode.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• Only S.DIRECT, TONE, SLEEP and AUDIO ASSIGN buttons will operate, after
pressing the SHIFT button.
•
The Product is not working
normally.
You have forgotten the rating
level password.
• With no disc in the product, press and hold the product's STOP ( I ) button for
longer than 5 seconds. INIT appears on the display and all settings will return
to the default values.
And then press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area
with good reception.
While listening to TV audio
through the Product, no sound is
heard.
•
If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the
TV functions, the BD/DVD functions are turned on and the TV audio is muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The BD/DVD’s software restricts it.
2. The BD/DVD’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot support
(for example, 1080p), you may not
see a picture on your TV.
• Press and hold the STOP ( I ) button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the product.
• Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution.
Abnormal HDMI output screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
Download from Www.Somanuals.com. All Manuals Search And Download.
English
81
Other Information
Symptom
Check/Remedy
There is no sound from surround
speakers.
• Are the surround speakers connected properly?
• Is Surround incorrectly set to NONE in the Speaker Size?
• Is surround mode set to stereo?
There is no sound from surround
back speakers
• Are the surround back speakers connected properly?
• Is SBACK (Surround Back) set to NONE in the Speaker Size?
• Is Surround Mode set to EX/ES?
Can't select EX/ES mode.
• Is SBACK (Surround Back) set to NONE in the Speaker Size?
• Is the input signal selected properly?
Can't select Dolby Pro Logic llx
mode.
• Is the input signal selected properly?
• Only 2 channel signal can select Dolby Pro Logic IIx mode. (ex:Dolby Digital,
PCM, 2 channel analog input signal.)
Can't select NEO:6 mode.
• Is the input signal selected properly?
• Use PCM and Analog input signal.
PC Share Manager function
I can see folders shared through
the PC Share Manager, but I
cannot see the files.
• Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
AllShare function
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
• Wireless connection between the server and the product is unstable.
Check the connection.
AllShare connection between TV
and PC is unstable.
•
IP address under the same subnetwork should be unique, otherwise IP collision
can results in such a phenomenon.
•
Check if you have a firewall enabled.
If so, disable the firewall function.
Download from Www.Somanuals.com. All Manuals Search And Download.
82
English
Symptom
BD-LIVE
Check/Remedy
I cannot connect to the BD-LIVE
server.
• Check whether the network connection is successful or not by using Network
Test menu.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
• Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
• If all above fails, contact the contents provider or update the latest firmware.
When using the BD-LIVE service,
an error occurs.
•
The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
NOTE
✎
When the factory default settings are restored, all the user data stored in the BD data will be deleted.
Repairs
If you contact us to repair your player, an administration fee may be charged if either:
1. An engineer is called out to your home at your request and there is no defect in the product.
2. You bring the unit to a repair center and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or begin
any work on your product.
com, or contact Samsung Customer Care at 1-800-SAMSUNG (726-7864) before seeking to repair
your product.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
83
Other Information
Specifications
Power Requirements
Power Consumption
AC 120V, 60Hz
125 W
Weight
General
18.74 Ibs
Dimensions
16.92 (W) x 6.50 (H) x 14.19 (D) inches
+41°F to +95°F
Operating Temperature Range
Operating Humidity Range
Signal/noise ratio
10 % to 75 %
65 dB
FM Tuner
Usable sensitivity
7 dB
Total harmonic distortion
BD (Blu-ray Disc)
0.9 %
Reading Speed : 9.834 m/sec
Reading Speed : 6.98 ~ 7.68 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
DVD (Digital Versatile Disc)
CD : 5 inches (COMPACT DISC)
CD : 3 1/2 inches (COMPACT DISC)
Composite Video
Disc
Blu-ray Disc : 480i
DVD : 480i
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
BD : 480i DVD : 480p, 480i
1080p, 1080i, 720p, 480p
Video Output
Video/Audio
Component Video
HDMI
PCM multichannel audio, Bitstream audio, PCM audio
Front speaker output
120W x 2(4
Ω
), THD 0.9%
), THD 0.9%
Surround Back / Front Height speaker output 120W x 2(4
Ω
Center speaker output
120W (4Ω), THD 0.9%
Surround speaker output
120W x 2(4Ω), THD 0.9%
Analog input
Digital input
75dB (1KHz)
70dB (1KHz)
(AUX) 450mV
20Hz~20kHz ( 3dB)
20Hz~40kHz ( -4dB)
Amplifier
Frequency response
S/N Ratio
Channel separation
Input sensitivity
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
84
English
SAMSUNG Receiver
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in
the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and
workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty
service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or
products if found to be defective during the limited warranty period specified above. All replaced parts and products become the
property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG's obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an
“AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent
otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including,
but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or
other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations,
repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions,
cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or
reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery
problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT
TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER°ØS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ07660-0511
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Area
Contact Center
Web Site
Area
Contact Center
Web Site
` North America
Canada
0700 Samsung (0700 726
7864)
Serbia
1-800-SAMSUNG (726-7864)
Slovakia
0800-SAMSUNG (726-7864)
Mexico
Spain
U.S.A
1-800-SAMSUNG (726-7864)
Sweden
0771 726 7864 (SAMSUNG)
` Latin America
Argentine
Brazil
ch_fr/(French)
0800-333-3733
0800-124-421 / 4004-0000
800-SAMSUNG (726-7864)
01-8000112112
0-800-507-7267
1-800-751-2676
1-800-10-7267
800-6225
0848-SAMSUNG (7267864,
Switzerland
CHF 0.08/min)
Chile
U.K
0330 SAMSUNG (7267864)
0818 717100
Colombia
Costa Rica
Dominica
Ecuador
Eire
Lithuania
Latvia
8-800-77777
8000-7267
Estonia
` CIS
800-7267
El Salvador
Guatemala
Honduras
Jamaica
1-800-299-0013
800-7919267
Russia
Georgia
Armenia
Azerbaijan
8-800-555-55-55
8-800-555-555
0-800-05-555
-
-
-
1-800-234-7267
00-1800-5077267
800-7267
Nicaragua
Panama
088-55-55-555
8-10-800-500-55-500
(GSM: 7799)
Kazakhstan
Uzbekistan
Kyrgyzstan
Tadjikistan
Peru
0-800-777-08
Puerto Rico
1-800-682-3180
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
Trinidad &
Tobago
1-800-SAMSUNG (726-7864)
0-800-100-5303
Venezuela
` Europe
Albania
ua_ru
Ukraine
0-800-502-000
42 27 5755
-
0810 - SAMSUNG (7267864,
€ 0.07/min)
Belarus
810-800-500-55-500
00-800-500-55-500
-
-
Austria
Moldova
` Asia Pacific
be (Dutch)
Belgium
02-201-24-18
Australia
1300 362 603
be_fr (French)
New Zealand
China
Bosnia
Bulgaria
Croatia
05 133 1999
07001 33 11
-
Hong Kong
(852) 3698 4698
hk_en/
800-SAMSUNG (800-726786)
3030 8282 / 1800 110011 /
India
Samsung Zrt., česká organizační
1800 3000 8282 / 1800 266 8282
Czech
složka, Oasis Florenc, Soko-
0800-112-8888 /
021-5699-7777
lovská394/17, 180 00, Praha 8
Indonesia
Denmark
Finland
France
Germany
70 70 19 70
Japan
0120-327-527
1800-88-9999
030 - 6227 515
01 48 63 00 00
Malaysia
1-800-10-SAMSUNG(726-7864) /
1-800-3-SAMSUNG(726-7864) /
1-800-8-SAMSUNG(726-7864) /
02-5805777
01805 - SAMSUNG (726-7864
€ 0,14/Min)
Philippines
Hungary
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
+381 0113216899
261 03 710
Singapore
Thailand
Taiwan
1800-SAMSUNG (726-7864)
Italia
Kosovo
-
0800-329-999
1 800 588 889
Luxemburg
Macedonia
Montenegro
Vietnam
` Middle East
Bahrain
023 207 777
-
020 405 888
-
0900-SAMSUNG
8000-4726
Netherlands
Norway
Poland
(0900-7267864) (€ 0,10/Min)
Egypt
08000-726786
800-22273
815-56 480
Jordan
0 801 1SAMSUNG (172678)
/ 022-607-93-33
Morocco
Oman
080 100 2255
800-SAMSUNG (726-7864)
9200-21230
Portugal
80820-SAMSUNG (726-7864)
Saudi Arabia
Turkey
1. 08010 SAMSUNG (72678) -
doar din reţeaua Romtelecom,
tarif local
444 77 11
U.A.E
800-SAMSUNG (726-7864)
Rumania
` Africa
2. 021.206.01.10 - din orice
reţea, tarif normal
Nigeria
0800-SAMSUNG (726-7864)
0860-SAMSUNG (726-7864 )
South Africa
Download from Www.Somanuals.com. All Manuals Search And Download.
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park,
NJ 07660-0511
1-800-SAMSUNG
(7267864)
IN THE US
Code No. AH68-02334S
Download from Www.Somanuals.com. All Manuals Search And Download.
|