SmartDome Camera
SCC-C6403P
E
Owner’s Instructions
êÛÍÓ‚Ó‰ÒÚ‚ÓÔÓθÁÓ‚‡ÚÂÎfl
Instrukcja obs∏ugi
RU
PL
Part : AB68-00572A(00)
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal
things) or containers filled with water on top of the camera. (Doing so may
cause personal injury due to fire, electrical shock, or falling objects.)
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
7. Do not install the unit in humid, dusty, or sooty locations.
(Doing so may cause fire or electrical shock.)
8. If any unusual smells or smoke come from the unit, stop using the product.
In such case, immediately disconnect the power source and contact the
service center. (Continued use in such a condition may cause fire or
electrical shock.)
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
9. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized
modifications or attempted repair.)
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
10. When cleaning, do not spray water directly onto parts of the product.
(Doing so may cause fire or electrical shock.)
Wipe the surface with a dry cloth. Never use detergents or chemical
cleaners on the product, as this may result in discoloration of surface or
cause damage to the finish.
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Caution
1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 122°F), low
temperature (below 14°F), or high humidity.
(Doing so may cause fire or electrical shock.)
3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators.
(Neglecting to do so may result in a risk of fire.)
4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.
5. Install in a well-ventilated location.
6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
Before Usage
Before Usage...............................................................................................................1-1
This is a basic instruction manual for the SCC-C6403P user.
It contains all the instructions needed to use the SCC-C6403P
from a simple introduction of the control locations and functions of
the SCC-C6403P to installation methods in the set up menu.
Chapter 1 SCC-C6403P Overview ...........................................................................1-4
SCC-C6403P Introduction...........................................................................1-5
Locations of Control….................................................................................1-6
ADAPTER CONNECTION ..........................................................................1-8
INITIAL SETTING........................................................................................1-9
Setting RS-422A/RS-485 termination........................................................1-10
E
We recommend all users of the SCC-C6403P from the advanced
user who has used similar cameras before to the general user to
read the instruction manual before using.
Chapter 2 SCC-C6403P Installation.........................................................................2-1
Before Installing...........................................................................................2-2
Preparing the Cables...................................................................................2-3
Cable Connection........................................................................................2-4
Installing SCC-C6403P................................................................................2-5
Installing the Camera ..................................................................................2-8
The most frequently used feature in the SCC-C6403P would be
the SCC-C6403P Setup Menu.
The SCC-C6403P Setup Menu is explained in detailed in
"Chapter 3 Setup Menu Overview".
Chapter 3 Setup Menu Overview .............................................................................3-1
Structure of the Setup Menu........................................................................3-2
1. CAMERA SET MENU .............................................................................3-4
- CAMERA ID .........................................................................................3-4
- V-SYNC................................................................................................3-5
- COLOR/BW..........................................................................................3-6
- MOTION DET.......................................................................................3-7
- ZOOM SPEED .....................................................................................3-8
- DIGITAL ZOOM ...................................................................................3-9
- DISPLAY ZOOM ..................................................................................3-9
- DISPLAY P/T .......................................................................................3-9
- EXIT ...................................................................................................3-10
2. VIDEO SET MENU ...............................................................................3-10
- IRIS....................................................................................................3-10
- ALC.................................................................................................3-10
- BLC...............................................................................................3-10
- MANU .............................................................................................3-11
- SHUTTER..........................................................................................3-12
- FLICKERLESS ................................................................................3-12
- AGC ...................................................................................................3-13
- MOTION.............................................................................................3-13
- WHITE BAL........................................................................................3-14
- DIS.....................................................................................................3-15
- FOCUS MODE...................................................................................3-16
- SPECIAL............................................................................................3-16
- EXIT...................................................................................................3-17
3. PRESET ................................................................................................3-17
- POSITION SET .................................................................................3-18
- PRESET ID........................................................................................3-18
- VIDEO SET........................................................................................3-18
- PRESET SPEED ...............................................................................3-18
- DWELL TIME.....................................................................................3-18
- IMAGE HOLD ....................................................................................3-18
- EXIT...................................................................................................3-18
The instructional manual is best used when read from beginning
to end, but for users wanting to read only the part they need here
are the Chapter summaries.
"Chapter 1 SCC-C6403P Overview" includes a brief introduction
of the SCC-C6403P, part names and functions, and Switch
Settings.
"Chapter 2 SCC-C6403P Installation" explains the installation
procedures of the SCC-C6403P and provides preparation and
installation environment requirements.
"Chapter 3 Setup Menu Overview" presents the structure of the
Setup menu for the SCC-C6403P including a detailed explanation
of the functions performed in each submenu.
"Appendix SCC-C6403P Product Specifications" contains
product specifications of the SCC-C6403P in itemized categories.
1-1
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
4. ZONE SET...............................................................................................3-19
- ZONE DIR SET....................................................................................3-19
- ZONE AREA SET................................................................................3-20
- LOCATION .......................................................................................3-21
- ZONE ID SET ...................................................................................3-21
- ZONE ENABLE.................................................................................3-21
5. AUTO SET...............................................................................................3-22
- AUTO PAN ..........................................................................................3-22
- POSITION SET.................................................................................3-22
- SPEED..............................................................................................3-23
- DWELL TIME....................................................................................3-23
- PATTERN............................................................................................3-23
- SCAN...................................................................................................3-24
- AUTO PLAY.........................................................................................3-25
- AUTO RETURN................................................................................3-25
- AUTO PLAY......................................................................................3-25
- PLAY NUMBER................................................................................3-25
6. ALARM SET ............................................................................................3-26
- ALARM PRIORITY SET ......................................................................3-26
- ALARM IN SET....................................................................................3-26
- ALARM OUT SET................................................................................3-26
- AUTO SET...........................................................................................3-27
- AUX OUT CONTROL ..........................................................................3-27
7. OTHER SET............................................................................................3-27
- PROPORTINAL P/T ............................................................................3-27
- TURBO P/T..........................................................................................3-28
- AUTO CAL...........................................................................................3-28
- AUTO FLIP ..........................................................................................3-28
- CAM RESET........................................................................................3-28
- LANGUAGE.........................................................................................3-28
- PASSWORD........................................................................................3-28
8. SYSTEM INFO ........................................................................................3-29
9. Short Keys...............................................................................................3-30
Chapter 1 SCC-C6403P Overview
In this chapter we will briefly introduce the SCC-C6403P
and show main functions, locations of control and Switch
Setting.
E
Product specifications ..........................................................................................3-32
1-3
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SCC-C6403P Introduction
Locations of Control
FRONT
SCC-C6403P is a zoom lens built in smart dome camera which
provides you with the best monitoring function in connection with
CCTV at banks or companies.
E
The SCC-C6403P is a high quality surveillance camera using x32
zoom lens and digital zoom IC, it can catch clear images up to 320
times.
SCC-C6403P has a variety of functions such as;
- DAY/NIGHT to improve the sensitivity by automatic conversion
into the black and white mode at night or in the environment with
low illumination,
- White Balance to control the brightness to the illumination,
- Backlight Compensation under spotlight or utmost bright
illumination,
- Auto Focus to automatically adjust the focus to the subject
movement,
- PAN/TILT for an easy operation.
The SCC-C6403P uses an Alarm function for alert situations and
moving camera in the direction you want, ZOOM-IN and
ZOOM-OUT functions can be remote controlled.
1-5
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
ADAPTER CONNECTION
BACK
SCC-C6403P Adapter BOARD
E
AC 24V
OUT
POWER
AC 24V
OUT
POWER
1-7
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETTING
Setting RS-422A/RS-485 termination
CAMERA ADDRESS SETUP
Use SW701, SW702, or SW703 for Camera Address setup. You may
allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702
the 2nd digit, and SW703 the 1st digit.
1
2
EX) In case of Camera Address 1, see the following figure for setup.
As it is shown in the structure map, when Controller and RS-422A/RS-
485 is connected it should be terminated according to the Cable feature
of impedance on the each end of the transmitting line to transfer the
signals in long distance by controlling the reflection of the signals to the
lowest.
E
SW701
SW702
SW703
Setting communication Protocol
Use number 1~4 PIN of SW704 to set communication Protocol.
Division
n < 32
PIN
A : SAMSUNG HALF
B : SAMSUNG FULL
PIN1 PIN2 PIN3 PIN4
OFF OFF OFF OFF
Comp
Termination
SW1-ON
A
B
C
D
E
F
G
H
I
ON
OFF
ON
OFF OFF OFF
ON
ON
OFF OFF
OFF OFF
SEE INSTRUCTION MANUAL
ON 1 2 3 4 5 6 7 8
SW704
(x1)
OFF OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
(x100) (x10)
ON
OFF
ON
OFF
ON
<RS-485 Half Duplex Organization>
SW701 SW702 SW703
ON
Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.
OFF OFF OFF
J
ON
OFF
ON
OFF OFF
ON
K
L
ON
ON
OFF
OFF
ON
ON
n < 32
ON
M
N
O
P
OFF OFF
ON
Division
SW1-ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
SW2-ON
(BOTTOM VIEW)
Division
ON
ON
ON
Baud Rate Setting
Use PIN 5 and 6 of SW704.
1
2
3
4
5
6
7
8
<RS-422A/RS-485 Full Duplex Organization>
ON
OFF
SW 704
PIN 6
ON
❈
A communication error may occur if you connect multiple cameras that are
assigned the same address in the network.
BAUD RATE
4800 BPS
PIN 5
ON
ON
9600 BPS
OFF
ON
OFF
OFF
19200 BPS
38400 BPS
OFF
The factory default setting is set to 9600BPS.
1-9
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Installing
Checking Package Contents
Please check that all components listed below are included in the
package:
Chapter 2 SCC-C6403P Installation
E
In this chapter, we will check the contents of the package before
installing the SCC-C6403P, and prepare a power adapter suitable for
the power supply system.
(Power Consumption: 18W; Voltage: AC24V, 1.5A)
Then, we will install the SCC-C6403P and connect the cables.
SCC-C6403
Bracket anchor
Owner’s
Instructions
AC 24V
OUT
POWER
Screws
Camera Holder
Adapter Board
Cover Body (Option)
2-1
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Connection
Preparing the Cables
1. First, connect one end of the
BNC video cable connector to
the Video Output Terminal
(VIDEO OUT)
To install and use the SCC-C6403P, the following cables should be
prepared.
Power Adapter Cable
The cable that plugs into the SCC-C6403P power input receptacle has the
rated voltage of AC24V, 1.5A.
Check the rated voltage before using the cable.
2. Then, connect the other end of
the connector to the Video Input
Terminal of the monitor.
E
3. Now connect the Power Adapter
Cable. Use a driver to screw
one part of the two lines of
Power Adapter to Power Input
Terminal of the SCC-C6403P.
Video Cable
The SCC-C6403P's cable is a BNC Cable for connecting the video-output
terminal to the video-input terminal of the monitor.
4. Adjust the switch on the Power Adapter to the proper voltage.
Then, connect the Power Adapter's plug to the Power Connector.
5. Connect the Remote Control
Terminal of the
SCC-C6403P
and the external Controller.
Controller
Adapter BOARD
2-3
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing SCC-C6403P
Installation Precautions
3) INDOOR HOUSING (SHG-120)
1) Make sure that the installation site can sufficiently support a minimum of
four times the net weight of the SCC-C6403P SmartDome Camera and
other accessories.
This housing is used for installing the SmartDome Camera to an indoor
wall or a ceiling.
2) Install in an area where the space above the ceiling board is over 18 cm
(7 in.) high.
3) Use the supplied screws to fasten the camera to the bracket assembly.
4) Keep persons away from the installation area, as there is a risk of falling
objects.
E
Also, move valuables to a safe location before installation.
Separately Sold Products for Installation
Depending on the installation site, it may be convenient to use one of the
following products.
1) CEILING MOUNT BRACKET
(SBR-100DCM)
4) OUTDOOR HOUSING (SHG-220)
This bracket is used for installing
the SmartDome CAMERA in the
plenum above the drop ceiling.
This housing is used for installing the SmartDome Camera to an
outdoor wall or a ceiling.
2) WALL MOUNT ADAPTOR
(SADT-100WM)
This adaptor is used for installing the
indoor housing or the outdoor
housing for the SmartDome Camera
on a wall.
❈
To install and use OUTDOOR HOUSING, remove the Clear Case
from the Camera body before installation.
2-5
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Camera
1. [Figure 1] Install the structure on the
ceiling.
(Refer to Installation reference
for the Length of the structure)
5) CEILING MOUNT ADAPTOR (SADT-100CM)
This adaptor is used for installing the indoor housing or the outdoor
housing for the SmartDome Camera to a concrete ceiling.
* Built in by the builder of the structure
E
[Figure 1]
2. Make a hole in the ceiling where the camera will be installed.
(The hole should be about
ø185)
3. [Figure 2] Assemble the
BRKT-ANCHOR on the ceiling
and screw the 4 bolts in.
6) POLE MOUNT ADAPTOR (SADT-100PM)
This adaptor is used for installing the WALL MOUNT ADAPTOR
(SADT-100WM) to a pole that is over 8 cm (2.76 in.) in diameter.
[Figure 2]
4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER.
(See page 2-4)
[Figure 3]
[Figure 4]
2-7
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. [Figure 5] Match the
6. Pull the safety wire from the case
body, and assembly it to the camera
holder.
BRKT-ANCHOR and CAMERA
ADAPTER and use 4screws
(PH M4 x 8) to assemble them.
Chapter 3 Setup Menu Overview
[Figure 5]
[Figure 6]
In this chapter, we will look over the Setup Menu of the
SCC-C6403P, First we'll look over the overall structure of the
Setup Menu, and then we'll look at the functions of each menu.
E
[Figure 7]
7. [Figure 7] Match the 3 holes on the
back of the CAMERA and the
CONNECTOR and turn it left about
15 degrees.
(Check the sound of LOCKING
and that the LEVER-LOCKING
is in place)
* Use the screws (BH M3 x L8) to
connect the CAMERA and the
ADAPTER so they don't move.
8. [Figure 8] Assemble the
[Figure 8]
COVER-BODY onto the DOME.
2-9
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Structure of the Setup Menu
ALARM SET
ALARM PRIORITY SET
ALARM IN SET
ALARM1~4 1~4
EXIT
QUIT/SAVE
CAMERA SET
CAMERA ID
V-SYNC
ON.../OFF
INT/LINE...
ALARM1~4
EXIT
NO/NC/OFF
QUIT/SAVE
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
EXIT
COLOR.../BW.../AUTO...
OFF/ON...
1/2/3/4
0FF/X2 ~ X10
OFF/ON
OFF/ON
ALARM OUT SET
ALARM1~4
MOTION
EXIT
1~3
1~3
QUIT/SAVE
E
QUIT/SAVE/PRESET
AUTO SET
ALARM1~4
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4
OFF/PATTERN1~3/HALF1~2/FULL/SCAN1~4
QUIT/SAVE
MOTION
EXIT
VIDEO SET
IRIS
SHUTTER
AGC/MOTION
ALC.../MANU...
OFF/1/100(1/120)~1/10K/AUTOX2...~X128...
OFF/LOW/HIGH(AGC)
S.SLOW/SLOW/NORM/FAST/F.FAST(MOTION)
AUX OUT CONTROL
OUT1 ON/OFF
OUT2 ON/OFF
OUT3 ON/OFF
EXIT QUIT/SAVE
WHITE BAL
DIS
FOCUS MODE
SPECIAL
ATW1/ATW2/AWC/MANU...
ON/OFF
ONEAF/MF
...
RET
Y-LEVEL
C-LEVEL
DETAIL
(0)l---
(0)l---
(0)l---
OTHER SET
PROPORTIONAL P/T
TURBO P/T
AUTO CAL
AUTO FLIP
CAM RESET
LANGUAGE
PASSWORD
EXIT
ON/OFF
ON/OFF
OFF/6H/12H/18H/24H
ON/OFF
...
ENGLISH/RUSSIAN/POLISH
ON.../OFF
QUIT/SAVE
RET
EXIT
QUIT/SAVE/PRESET
PRESET
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
EXIT
...
ON.../OFF
ON.../OFF
1~8
SYSTEM INFO
1~60S
ON/OFF
QUIT/SAVE/DEL
The diagram shown above illustrates the overall structure of the Setup Menu.
In this section, a description of the Setup menu features will enable users of the
SCC-C6403P to tailor it to their personal needs.
ZONE SET
AUTO SET
ZONE DIR SET
ZONE AREA SET
EXIT
OFF/ON...
OFF/ON...
QUIT/SAVE
AUTO PAN
PATTERN
SCAN
AUTO PLAY
RET
1.../2.../3.../4...
1.../2.../3...
1.../2.../3.../4...
...
3-2
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
(CAMERA ID)
(CAMERA SET)
❈
If the power is turned off after PRESET, AUTO PAN, SCAN,
PATTERN function is activated and no other control is made, camera
will do the same function after the power is turned on.
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
ON...
INT
A B C D E F G H I J K L
M N O PQ R S T U V W X
Y Z 0 1 2 3 4 5 6 7 8 9
COLOR...
OFF
3
❈
:
!
- +
❈
(
)
/
Press
OFF
SP ï î SP
LOCATION...
RET
Use the controller to press the MENU selection key and the following
screen will be displayed.
[Enter]
DISPLAY ZOOM OFF
DISPLAY P/T
OFF
SCC-C6403........
EXIT
QUIT
** MAIN MENU **
CAMERA SET...
❈ " ... " Means there are Sub Menus.
0
5
1
6
2
7
3
8
4
9
VIDEO SET...
PRESET ...
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
E
❈❈❈❈❈❈❈
V-SYNC
In the V-SYNC menu, vertical synchronization can be selected. The
vertical synchronization signal supported by the SCC-C6403P is the INT
mode made by clock inside the SCC-C6403P and LINE mode adjusting
vertical synchronization to the exterior power frequency.
❈ PASSWORD
DEFINED
PASSWORD
UNDEFINED
❈
Select LINE and press [Enter]. You will see the LINE LOCK submenu
where you can adjust the phase of the LINE LOCK.
You can use the PHASE menu of the LINE LOCK submenu to assign as
much PHASE as you want.
In case of , use UP/DOWN/LEFT/RIGHT/[ENTER] key for MENU
❈
setup. In case of , type in the 4 digit password first. If correct, the
❈
MENU selection screen like
will be displayed and you will be able to
❈
set up MENU by pressing UP/DOWN/LEFT/RIGHT/[ENTER] key.
(CAMERA SET)
(LL-PHASE)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
LINE...
COLOR...
OFF
1. CAMERA SET MENU
❈
3
OFF
Press
CAMERA ID
[Enter]
DISPLAY ZOOM OFF
DISPLAY P/T
OFF
The CAMERA ID menu assigns an ID to the SCC-C6403P to be displayed
on the connected monitor.On the CAMERA SET menu screen, select
CAMERA ID to ON and press [Enter]. You will see the sub screen for
deciding on the ID of the SCC-C6403P. The Camera ID can have up to 20
alphanumeric characters, along with several special characters.
The assigned camera ID may be positioned to any desired location on the
screen by using the LOCATION submenu.
PHASE
RET
(-262)I--------
EXIT
QUIT
3-4
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
COLOR/BW
❈❈In AUTO mode, AGC will be displayed as “---“. You can’t adjust the
settings manually.
In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.
In a poor illumination environment, the IR filter is turned off in the BW mode the its
sensitivity increases as high as a black and white camera. On the other hand, the
IR filter is turned on and the sensitivity decreases in the COLOR mode.
(CAMERA SET)
(AUTO)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
COLOR
: The IR Filter is ON and the screen is normal. You can press the
[Enter] key to set the COLOR GAIN LEVEL. And when the AGC
function is on, you can set the AGC COLOER LEVEL.
❈
AUTO...
OFF
3
Press
OFF
BURST
LEVEL
DURATION
RET
ON
LOW
S --|---- L
[Enter]
DISPLAY ZOOM OFF
DISPLAY P/T
OFF
(CAMERA SET)
(COLOR)
EXIT
QUIT
E
CAMERA ID
V-SYNC
COLOR/BW
MOTION
ZOOM SPEED
DIGITAL ZOOM OFF
DISPLAY ZOOM OFF
DISPLAY P/T
OFF
INT
COLOR …
❈
OFF
3
Press
Caution : If you use an infrared light source while in AUTO mode, AUTO
[Enter]
switching malfunction and camera AF malfunction may occur.
GAIN
AGC COLOR
RET
(0)I--------
(0)----I----
OFF
EXIT
QUIT
MOTION DET
BW
: The IR Filter is OFF and the screen is black and white.
In MOTION DET, you can set the Motion Detection function, Motion Detection
Sensitivity, and the Area of Motion Detection. If the Motion Detection function
is set, the movement of an intruder can be detected. When motion is detected,
it sets off the Alarm signal of the Controller.
(Sensitivity to low light is increased to a level comparable to a black
and white camera.)
Select BW and press [ENTER] and the additional menu to select
BURST ON/OFF will appear.
AUTO
: Select to automatically switch between the COLOR mode and BW
mode depending on the amount of light. In low light conditions, the
IR Filter is turned OFF and the sensitivity to low light is increased
by switching to the BW mode, but in bright light conditions, the IR
Filter is turned ON and the sensitivity is decreased by switching to
the COLOR mode.
(CAMERA SET)
(MOTION DET)
CAMERA ID
V-SYNC
OFF
INT
COLOR...
ON...
3
OFF
OFF
OFF
COLOR/BW
❈
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
Press
[Enter]
AREA
USER...
Select AUTO and press [ENTER] and the additional menu to select
BW LEVEL and DURATION will appear.
SENSITIVITY L ---|--- H
RET
EXIT
QUIT
- BURST ON : The color burst signal is output together with black and white
composite video signal.
- BURST OFF : The color burst signal is not output.
- LEVEL
: You can set the brightness level that changes from COLOR mode
to BW mode in 3 steps : LOW, MEDIUM, and HIGH.
- DURATION : Set the HOLDING time for switching between COLOR and BW
mode depending the changes in the amount of light. You can set
the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).
3-6
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Select ON and press [Enter ] to display an additional menu window of
“MOTION DET ”.
DIGITAL ZOOM
You may set up the digital zoom magnification ratio in the DIGITAL ZOOM
menu. The magnification ratio ranges from OFF to 10. If you set Digital
Zoom of SCC-C6403P to max. 10 times, the mode will become the 32 time
optical zoom and you will be able to enlarge a subject by max. 320 times.
Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.
You can select one from the sub items of TOP..., BOTTOM..., LEFT...,
RIGHT..., CENTER... or USER... as AREA where the Motion Detection
function is applied.Select one from TOP..., BOTTOM..., LEFT..., RIGHT...,
CENTER... or USER... and press [Enter ]. You ’ll see the factory defaults of
that item and Motion Detection will be applied to the area you selected.
If you set the AREA menu to USER and press [ENTER], you may vary the size
and position of the area where you want to apply the MOTION detection
function by yourself. Press Left, Right, Up, or Down to select an area AREA.
Press ENTER and then Left, Right, Up, or Down to select a LOCATION. Press
ENTER again to move back to the upper menu.
Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION
detection area.
Press [ENTER] again and you will escape the AREA setup menu.
Use SENSITIVITY to set up the sensitivity of MOTION detection strength.
The higher, the more sensitive.
(CAMERA SET)
(CAMERA SET)
CAMERA ID
V-SYNC
OFF
INT
BW...
OFF
3
OFF
OFF
OFF
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
BW...
OFF
3
❈
E
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
DISPLAY ZOOM
DISPLAY P/T
Use the
[Left, Right]
Keys
X10
DISPLAY ZOOM OFF
DISPLAY P/T
OFF
EXIT
QUIT
EXIT
QUIT
AREA
DISPLAY ZOOM
AREA
In DISPLAY ZOOM, you can display the ZOOM scale on the screen.
❈
(CAMERA SET)
Use the
[Left, Right, Up, Down]
Keys
X020
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
COLOR...
OFF
4
LOCATION
LOCATION
OFF
DISPLAY ZOOM ON
DISPLAY P/T
OFF
SAVE
❈
❈
After PAN/TILT/ZOOM/FOCUS/IRIS movement finishes, MOTION DET function
will not work for about 5 seconds to stablize the chage of the screen.
EXIT
MOTION detection function operates based on the brightness change within the
setup region. Therefore, erroneous operation may occur depending on the
brightness difference between the background and the object that is being
taken, or the status of the area setup, etc.
❈ If no change on the ZOOM scale is made for 3 seconds, the information window will
disappear.
DISPLAY P/T
ZOOM SPEED
In DISPLAY P/T, you can display the position of Pan/Tilt on the screen.
In the ZOOM SPEED menu you can select the speed of the ZOOM Key
(Tele/Wide).
Use the [Left] or [Right] keys in the ZOOM SPEED menu to select
the speed.
(CAMERA SET)
347/060
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
COLOR...
OFF
4
OFF
1 : Slowest speed
2 : Low speed
3 : High speed
4 : Fastest speed
DISPLAY ZOOM OFF
DISPLAY P/T
ON
EXIT
SAVE
❈ If no change on the Pan/Tilt position is made for 3 seconds, the information window
will disappear.
❈ It allows an error range of 2°.
3-8
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
For items in the BLC menu, the user can set the size and location of the
BLC area by pressing [ENTER] key after put the cursor on USER… using
the [Left, Right] key. For SIZE items, you can use the [Up, Down, Left,
Right] key to designate the SIZE, and then press the [ENTER] key.
You can set the location for areas using the [Up, Down, Left, Right] key in
the LOCATION.
EXIT
The EXIT menu is used to quit the CAMERA SET menu of the
SCC-C6403P and return to the MAIN MENU.
- QUIT
: Ignores the changed information and restores the saved
information.
- SAVE : Saves the information of the setting condition of the menu.
- PRESET: Ignores the changed information and restores the initial
factory defaults of the menu.
(ALC)
SIZE
2. VIDEO SET MENU
IRIS
There is a function to automatically adjust IRIS to the incoming light level.
Owing to this function, you may set up the brightness level yourself.
The ALC(Auto Light Control) menu allows you for video output level setup.
❈
E
Press
[Enter]
BLC
LEVEL
RET
USER...
(0) ----I----
LOCATION
SIZE
ALC
SIZE
Choose the ALC of the IRIS item and press [ENTER] and set he submenu
to the Video Output level and BLC will be shown.The Video Output Level
can be set in the level item using the [Left, Right] keys.
❈
Press
BLC (Submenu of the ALC menu)
[Enter]
If you use a general camera to photograph a subject under backlight or
bright illumination, the subject will be shown dark on the monitor due to
the backlight. BLC(Back Light Compensation) is used to prevent such a
backlight problem to secure distinct images under bright illumination.
Using the [Left, Right] keys, you can set up BOTTOM…, TOP…, LEFT…,
RIGHT…, CENTER… 5 preset areas and the USER…function that can
directly set the areas. For example, for the items in the BLC menu, you
can confirm the preset BOTTOM area by pressing [ENTER] key in the
BOTTOM… status.
LOCATION
LOCATION
Use [Left, Right] key in the LEVEL menu to control the video output
level(brightness).
(VIDEO SET)
(ALC)
IRIS
ALC...
AUTO X2...
NORM
ATW1
---
MANU
SHUTTER
MOTION
WHITE BAL
DIS
FOCUS MODE ONEAF
SPECIAL
❈
When you press [ENTER] key after selecting MANU in the IRIS item, an
additional screen appears in which you can set manually opening or closing
the IRIS.
Press
[Enter]
BLC
LEVEL
RET
OFF
(0)----I ----
...
EXIT
QUIT
(VIDEO SET)
(MANUAL)
(ALC)
IRIS
SHUTTER
AGC
MANU...
OFF
OFF
❈
WHITE BAL
DIS
FOCUS MODE ONEAF
SPECIAL
EXIT
ATW1
OFF
Press
❈
[Enter]
Press
LEVEL
RET
(00) ----I----
...
QUIT
[Enter]
BLC
LEVEL
RET
BOTTOM...
(0)----I----
3-10
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SHUTTER
AGC
You may designate both the fast electronic shutter speed and low
electronic shutter speed in the SHUTTER menu. The fast electronic
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to
be used for the bright and fast video image. The AUTO slow electronic
shutter supports 12 shutter speeds from x2 to x160 and sets the shutter
speed to be slow In order to make the image on the screen more distinct
and brighter when you photograph under dark illumination. If you want to
sense the light brightness to control the shutter speed to the brightness
automatically, select the AUTO slow shutter.
The AGC menu was designed to provide you with brighter screen
supposed you photographed any subject in the dark resulting in less
brighter image than regulated. AGC menu setup is available only when
the SHUTTER menu is set to Fast Shutter or Off. Press either Left and
Right to go to LOW or HIGH and the AGC function will be activated. LOW
is use to lower the maximum AGC GAIN and HIGH raise the maximum
AGC GAIN.
(VIDEO SET)
(VIDEO SET)
E
IRIS
SHUTTER
AGC
ALC...
OFF
LOW
IRIS
SHUTTER
AGC
ALC...
OFF
OFF
WHITE BAL
DIS
ATW1
OFF
WHITE BAL
DIS
ATW1
OFF
FOCUS MODE
SPECIAL
EXIT
ONEAF
...
QUIT
FOCUS MODE
SPECIAL
EXIT
ONEAF
...
QUIT
Keep pressing both Left and Right in the SHUTTER menu, the speed will
change in the following sequence.
❈❈OFF ❈ AUTO X2... ❈ AUTO X4... ❈ AUTO X6... ❈ AUTO X8... ❈ AUTO X12... ❈
AUTO X16... ❈ AUTO X24... ❈ AUTO X32... ❈ AUTO X48... ❈ AUTO X64... ❈
AUTOX96... ❈ AUTO X128... ❈ OFF ❈ 1/100(1/120) ❈ 1/250 ❈ 1/500 ❈ 1/1000 ❈
1/2000 ❈ 1/4000 ❈ 1/10K
❈❈When the COLOR/BW menu of the camera set is set to AUTO..., AGC will
be displayed as “---“. You can’t adjust the settings manually.
MOTION
The MOTION function is available only when the SHUTTER men is set to
Slow Shutter AUTO, being composed of 5 steps, S.SLOW, SLOW,
NORM, FAST, F.FAST.
❈ S.SLOW reduces the amount of AGC as much as possible to monitor
subjects with no immobility in the dark.
❈ SLOW reduces the amount of AGC to monitor subjects with little
immobility in the dark.
❈
❈
If you set SHUTTER to between AUTO X4... and AUTO X128..., FOCUS mode will be displayed
as “MF“ (the product can operate only in MF mode). You can ’t adjust the settings manually.
If you set it to OFF, 1/100(1/120)/10K or AUTO X2..., the product will recover the previous
FOCUS mode.
If you set SHUTTER to between AUTO X2... and AUTO X128..., DIS will be displayed as
“---“ (it can only operate in Off mode). You can ’t adjust the settings manually.
If you set it to OFF or 1/100(1/120)/10K, the product will recover the previous settings of DIS.
❈
NORM sets the amount of AGC to the middle to monitor mobile subjects in the dark.
❈ FAST raises the amount of AGC to monitor fast subjects in the dark.
❈ F.FAST reduces the amount of AGC as much as possible to monitor
very fast subjects in the dark.
When the SHUTTER menu is set to AUTO, press Down to locate the
cursor in the MOTION menu and press Left and Right for MOTION
function setup. Press Left to the SLOW side and Right to the FAST side.
FLICKERLESS
Either NTSC (for 50 Hz)or PAL (for 60 Hz areas)is an anti-flickering system that is
designed to avoid image flickering on the screen due to inconsistency between the
vertical synchronizing frequency of the picture and the flashing frequency of the
lightening. If you select and set AUTO to ON in SHUTTER from VIDEO SET, you can set
NTSC or PAL for your area and the auto shutter speed is fixed at 1/100(1/120) second.
(VIDEO SET)
(FLICKERLESS)
(VIDEO SET)
IRIS
ALC...
AUTOX2...
NORM
ATW1
---
IRIS
ALC...
AUTO X2...
F.FAST
ATW1
---
ONEAF
...
QUIT
❈
SHUTTER
MOTION
WHITE BAL
DIS
SHUTTER
MOTION
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
Press
[Enter]
FOCUS MODE ONEAF
FLICKERLESS
RET
OFF
SPECIAL
EXIT
...
QUIT
3-12
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
You can select one of four modes for white balance adjustment as follows:
WHITE BAL
Lights are generally denoted as color temperatures and expressed in
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.
Kelvin (
K) units.
The general light color temperatures are shown below.
ATW1 : 2500K ~ 9300K(
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(
❈❈1. If the color temperature is out of this range in ATW1 mode, proper
❈1)
❈2)
10000K
9000K
Blue sky
white balance may not be obtained. In that case, select ATW2 mode.
❈❈2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
Rainy
E
Therefore, select the mode which is appropriate for the environment.
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.
8000K
7000K
Cloudy
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.
6000K
Partly Cloudy
Sunny
5000K
4000K
- 3200
K
K
: Set color temperature to 3200
K
K
- 5600
: Set color temperature to 5600
- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.
Fluorescent lamp
3000K
Halogen lamp
Candlelight
(VIDEO SET)
(AWB/MANU)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
LOW
MANU...
ON
ONEAF
...
❈
2000K
1000K
Press
Tungsten lamp
PRESET
RET
3200K
[Enter]
QUIT
DIS
The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.
❈❈It is recommended to deactivate the DIS function in the no vibration
environment.
❈❈From VIDEO SET, if you set SHUTTER to between AUTO X2... and AUTO
X128... DIS will be displayed as “---“ (it can operate only in Off mode).
You can’t adjust the settings manually.
3-14
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
EXIT
FOCUS MODE
It's the same as the EXIT function of the CAMERA SET menu.
In the FOCUS MODE MENU, the Focus method can be set to ONEAF
(One Auto Focus), or MF(Manual Focus).
- ONEAF : In the ONEAF mode, it automatically sets the focus after the
PAN/TILT/ZOOM moves, and operates as the same in the MF mode if the
PAN/TILT/ZOOM does not move.
3. PRESET
This is the menu that user sets the PAN/TILT location, Zoom/Focus, and
screen condition, so the camera can monitor the presetting area on
demand. A total of 128 presets are available.
- MF
: In MANUAL FOCUS MODE the user adjusts the Focus manually.
Use the left/right keys to select ONEAF orMF in the FOCUS MODE menu.
(VIDEO SET)
E
IRIS
SHUTTER
AGC
WHITE BAL
DIS
ALC...
OFF
OFF
ATW1
OFF
** MAIN MENU **
(PRESET MAP)
CAMERA SET...
FOCUS MODE
SPECIAL
EXIT
ONEAF
...
QUIT
VIDEO SET...
PRESET ...
0
5
1
6
2
7
3
8
4
9
❈
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31
ID:PRESET 0
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
Press
[Enter]
❈❈ONEAF can only be selected if SHUTTER is set to OFF, 1/100(1/120)
~1/10K, or AUTOX2...
î
ï
RET
In other modes (AUTOX4...~AUTOX128...), FOCUS mode will be
displayed as “MF“(the product automatically switches into MF mode).You
can ’t adjust the settings manually.
❈❈ONEAF function may not possible withe types of objects listed below. For
such objects, focus manually.
PRESET NO.0
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
...
- High intensity objects or objects illuminated with low lighting
- Obejects shot through wet or dirty glass
❈
ON...
OFF
8
3S
OFF
Press
- Pictures that are a mixture of distant and nearby objects
- White alls and other single-color objects
- Venetian blinds and other horizontally striped objects
[Enter]
EXIT
QUIT
SPECIAL
In SPECIAL menu, you can directly adjust Y-LEVEL, C-LEVEL, and DETAIL
functions.
- Y-LEVEL : It is used to set the levels for the Sync signal and the entire
brightness signal of the video signal.
- C-LEVEL : It is used to set the levels for the Burst signal and the entire colour
signal of the video signal.
- DETAIL : Controls both horizontal and vertical distinction.
(VIDEO SET)
(SPECIAL)
IRIS
SHUTTER
AGC
ALC...
OFF
ON
❈
WHITE BAL
DIS
ATW1
ON
Press
Y-LEVEL
C-LEVEL
DETAIL
RET
(0)I--------
(0)I--------
(0)--I-
FOCUS MODE
SPECIAL
ONEAF
...
[Enter]
EXIT
QUIT
3-16
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITION SET
From "POSITION SET..." press [ENTER] to get into the PAN/TILT,
FOCUS/ZOOM SET screen
to set the PAN/TILT location and FOCUS/ZOOM condition then press
[ENTER] to return to a higher menu.
4. ZONE SET
The ZONE SET menu includes the setup of ZONE DIRECTION, and
ZONE AREA.
** MAIN MENU **
(ZONE SET)
PRESET ID
This is the ID set up function for each PRESET.
It can be set up to 12 characters using the left, right, up, and down keys.
The ID location can be set in the submenu of "LOCATION..."
CAMERA SET...
VIDEO SET...
ZONE DIR SET
OFF
PRESET...
❈
ZONE AREA SET OFF
E
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
Press
[Enter]
EXIT
QUIT
VIDEO SET
This is the screen setting function for each PRESET.
Refer to the explanation under "VIDEO SET menu".
ZONE DIR SET
PRESET SPEED
Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the
SET NORTH screen. MAP. Move PAN to set the SET NORTH position
and press [ENTER]. Based on the North position,the direction of N(North),
NE(North-East), E(East), SE(South-East), S(South), SW(South-West),
W(West), NW(North-West) is displayed whenever you move PAN.
This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)
to 8(FAST).
- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec
- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec
DWELL TIME
This is a function setting for the DWELL TIME of the PRESET location in
"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.
(ZONE SET)
SET NORTH
ZONE DIR SET
ZONE AREA SET
ON...
OFF
❈
N
IMAGE HOLD
Press
Pauses the image when PRESET is in movement, If you set the IMAGE
HOLD menu to ON, the screen will be paused until PRESET finishes
moving.
[Enter]
EXIT
QUIT
EXIT
"QUIT" : Does not save the selected information and returns to a higher
menu.
"SAVE" : Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.
Then returns to a higher menu.
3-18
3-19
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONE AREA
LOCATION
The “LOCATION...” menu designates the left/right LIMIT positions of
ZONE AREA. Enter the setup screen to move PAN, then select a start
position and press [ENTER]. Move PAN again
to select a end position and press [ENTER]. Now, ZONE AREA setup is
complete.
Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE
AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP
screen and press [ENTER] to enter the ZONE AREA setup screen.
ZONE AREA SET
0
SET START!
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
(ZONE SET)
(ZONE AREA MAP)
❈
❈
ZONE DIR SET
ZONE AREA SET
OFF
ON...
E
0
4
1
5
2
6
3
7
*
After P/R/Z
control, press
[ENTER]
Press
❈
[Enter]
Press
[Enter]
EXIT
QUIT
EXIT
QUIT
SET END!
After PAN control,
press [ENTER] to
finish.
ZONE AREA SET
0
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
❈
Press
[Enter]
EXIT
QUIT
ZONE ID SET
This function is used to allocate as many as 12 IDs to each zone area.
Use Left , Right, UP, or DOWN for this purpose. You may select the ID
position from the additional menu of “LOCATION...”.
ZONE AREA ID 0
ZONE AREA SET
0
A B C D E F G H I J K L
M N O P Q R S T U V W X
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
❈
Y Z 0 1 2 3 4 5 6 7 8
- +
9
:
!
❈
(
)
/
Press
SP ï î SP
LOCATION...
RET
[Enter]
ZONE 0........
EXIT
QUIT
ZONE ENABLE
This function turns on or off the ZONE AREA ID indication.
3-20
3-21
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED
5. AUTO SET
This is a setting function for movement speed setup. It can be set from
STEP1 to STEP64.
The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is
able to set up the AUTO PLAY motion.
DWELL TIME
This is a function for setting up the time to stay in the START to END position.
AUTO PAN
After selecting the locations of two points (PAN/TILT) of START and END,
it loops continuously in the set up SPEED. The number of AUTO PAN is
up to 4.
PATTERN
This is a replay function so that the MANUAL functions such as PAN, TILT,
ZOOM, and FOCUS, IRIS are played for 2 minutes.
E
** MAIN MENU **
(AUTO SET)
CAMERA SET...
VIDEO SET...
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
PRESET...
❈
❈ When the PATTERN is saved/executed, the PAN/TILT is operated with
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
Press
PROPORTIONAL ON, TURBO OFF.
AUTO PLAY
[Enter]
❈ If the SSC-1000 or SSC-2000 is used when uploading/downloading the
menu setup, reset the PATTERN because it may be different with the first
setting.
RET
AUTO PAN
1
POSITION SET
SPEED
...
22
❈
DWELL TIME
3S
Press
[Enter]
EXIT
QUIT
POSITION SET
The menu “POSITION SET …” sets the Start / End position of AUTO PAN.
Return to the settings screen and set the desired START position for
PAN/TILT, and then press the [ENTER] key. And, set the END position for
the PAN/TILT. Press the [ENTER] key to finish the setup for AUTO PAN
Start/End positions.
3-22
3-23
Download from Www.Somanuals.com. All Manuals Search And Download.
** MAIN MENU **
CAMERA SET...
VIDEO SET...
PRESET...
AUTO PLAY
(AUTO SET)
AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there
is no camera action after AUTO RETURN finishes.
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
❈
❈
ZONE SET...
Press
Press
AUTO SET...
AUTO PLAY
[Enter]
[Enter]
ALARM SET...
OTHER SET...
SYSTEM INFO...
(AUTO PLAY SET)
RET
(AUTO SET)
AUTO RETURN 12HOUR
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
AUTO PLAY
SCAN
PATTERN SET 1
❈
PATTERN SET 1
❈
PLAY NUMBER
1
Press
SET START POSITION
AND ENTER
AUTO PLAY
E
After
PATTERN
START
[Enter]
EXIT
SAVE
RET
position setup,
press
[ENTER].
AUTO RETURN
This menu sets up the time during which AUTO PLAY repeats.
PATTERN can be set upto 3. Choose 1, 2, or 3 with the left or right key in the
"PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From
the moment "PATTERN 1 SET" is gone for 2 minutes, it memorizes the MANUAL
movements and after 2 minutes it will return to a higher menu. If you want to finish
set up before the 2-minutes ends, press [ENTER].
AUTO PLAY
This function sets up the motion which will be repeatedly performed by
SCC-C6403P whenever the time set by AUTO RETURN elapses. It covers SCAN,
AUTO PAN, PATTERN, and PRESET setup.
PLAY NUMBER
This menu allocates a number to the motion set by AUTO PLAY. The numbers
range from 1 to 4 for SCAN AND AUTO PAN, 1 to 3 for PATTERN, and 0 to 127
for PRESET.
SCAN
SCAN sets the direction of PRESET movement during “SCAN” operation. The
number of SCAN is up to 4 and each SCAN is able to allocate 32 PRESETs as a
maximum.
(SCAN MAP 1)
(AUTO SET)
0*S 1*
2
7
3
8
4
9
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
5
6
❈
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31
EXIT
Press
AUTO PLAY
[Enter]
î
ï
SAVE
RET
If you enter the SCAN SET screen, SCAN MAP will be displayed. Move the cursor
to the number marked * where PRESET is saved and press [ENTER] and
S will appear and a PRESET will be included in SCAN.
3-24
3-25
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO SET
6. ALARM SET
This menu designates what to do at the time of ALARM input. Once an
alarm is given, the camera will shortly move to the PRESET position
corresponding to the respective alarm as follows.
PRESET1 to ALARM1~4
PRESET5 to MOTION
After DWELL TIME at a PRESET position, PATTERN or SCAN will be in
action according to the AUTO SET setup.
It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an
ALARM input from exterior SENSORs and it performs with PRESET or
PATTERN function and outputs the ALARM OUT signals.
Alarm operation time depends on the Preset Dwell time corresponding to
the alarm and whether AUTO is involved.
Setup of OFF/PATTERN 1~3/HALF1/HALF2/FULL/SCAN1~4 is available.
OFF dues not perform PATTERN or SCAN after moved to PRESET and
each menu has its own function as follows.
** MAIN MENU **
( ALARM SET)
E
CAMERA SET...
PATTERN 1~3 : Preset PATTERN action,
ALARM PRIORITY SET ...
ALARM IN SET..
ALARM OUT SET..
AUTO SET..
VIDEO SET...
PRESET...
❈
HALF1 : Continuous operation of PATTERN1 + PATTERN2
HALF2 : Continuous operation of PATTERN2 + PATTERN3
FULL : Continuous operation of all the aboves
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
Press
AUX OUT CONTROL..
[Enter]
SCAN 1~4 : Scanning as set
RET
AUX OUT CONTROL
This sets the ALARM OUT motion to continue or act only when the
ALARM is working.
If it is set to OFF the ALARM OUT motion will operate only when the
ALARM is working.
(Active "Low"), and if it's set to ON, the ALARM OUT will always operate
regardless of the ALARM.
ALARM PRIORITY SET
This sets the priority of the 4 ALARM inputs so ALARM can work
corresponding to the priority.
The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4.
If the ALARM is working at the same time and the priority is the same, it
will operate according to the DEFAULT priority. While the ALARM is
working, it cannot detect MOTION.
ALARM IN SET
This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or
"OFF" depending on the features of the SENSOR connected.
7. OTHER SET
PROPORTIONAL P/T
This function controls the PAN/TILT speed to the ZOOM magnification
ratio during the manual operation of PAN/TILT. If you set
PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the
ZOOM WIDE mode and decrease in the ZOON TELE mode even in the
same manual operation.
ALARM OUT SET
Each ALARM input corresponds to one of the 3 ALARM OUT.
3-26
3-27
Download from Www.Somanuals.com. All Manuals Search And Download.
(PASSWORD)
TURBO P/T
(OTHER SET)
PROPORTIONAL P/T ON
This function doubles up the speed of PAN/TILT movement by manual
operation of PAN/TILT. The speed may go up to 180°/sec(PAN).
0
5
1
6
2
7
3
8
4
9
TURBO P/T
AUTO CAL.
AUTO FLIP
CAM RESET
LANGUAGE
PASSWORD
OFF
OFF
ON
...
ENGLISH
ON...
❈
❈❈❈❈❈❈❈
❈❈❈❈❈❈❈
Press
[Enter]
AUTO CAL
This function turns on or off Auto Calibration. SCC-C6403P has the Auto
Calibration function to improve the precision of LENS and PAN/TILT
motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for
the time designated by the user, A.C will appear on the screen while
initializing LENS and PAN/TILT.
RET
EXIT
QUIT
Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and
press [ENTER] for password setup. After you finish inputting the 4 digits
password and the 2nd row of the 4 digits PASSWORD input screen, input
the selected password again for reassurance.
E
AUTO FLIP
If correct, the cursor will move to RET.
Press [ENTER] at RET, and the selected password will be saved,
returning to the OTHER SET screen.
Default password is 0123.
When TILT is set to a 90° limit using the joystick, PAN automatically
rotates by 180°
enabling you to see up to the Tilt area on the opposite side .
You can obtain an extended effect with the 180° operational range of the
TILT feature.
8. SYSTEM INFO
This menu allows you to check S/W version, communication protocol,
baud rate, and address of SCC-C6403P.
CAM RESET
CAM RESET clears all the settings made so far and restores the factory
default settings.
"CAMERA RESET?" message appears when you select CAM RESET.
Select "CANCEL" to return to the menu setup display or select OK to
restore the factory default settings.
** MAIN MENU **
( SYSTEM INFO)
CAMERA SET...
ALARM VER. V1.000
VIDEO SET...
MOTOR VER. V1.000
❈
PRESET...
CAMERA VER. V1.000
EEPROM VER. V1.000
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
Press
[Enter]
PROTOCOL
SAMSUNG
COMM. TYPE RS-485,HALF
BAUD RATE
ADDRESS
SERIAL NO.
RET
9600
❈❈ Be careful when performing a CAM RESET operation, as it deletes all
0
000000000000000
setup values.
LANGUAGE
This function selects a language for MENU setup. Press LEFT/RIGHT key to
choose English, Russian or Polish and the selected language will be applied
to the full screen.
PASSWORD
This function selects or cancels the MENU setup password. Press
[ENTER] at the state of PASSWORD ON..., and the following screen will
appear for password setup.
3-28
3-29
Download from Www.Somanuals.com. All Manuals Search And Download.
9. SHORT KEYS
SSC-1000 or SSC-2000 Controller supports the following short keys.
Function
Key
CAMERA SET…
COLOR/BW
COLOR/BW
COLOR/BW
❈ SCC-C6403P has two FANs inside for preventing overheating.
If FAN doesn't work properly, messages below will be displayed.
In those case, replace the FAN.
COLOR
BW
[PRESET] + [1] + [2] + [8] + [Enter]
[PRESET] + [1] + [2] + [9] + [Enter]
[PRESET] + [1] + [3] + [0] + [Enter]
AUTO
- ALARM FAN ERROR !
: This message is displayed when the FAN which is located bottom of
SCC-C6403P does not work properly.
VIDEO SET…
IRIS
E
ALC
[PRESET] + [1] + [3] + [2] + [Enter]
[PRESET] + [1] + [3] + [4] + [Enter]
[PRESET] + [1] + [3] + [5] + [Enter]
FOCUS MODE
FOUCS MODE
MF
Contact your nearest Samsung Electronics Service Center or designated
retailer before replacing the FAN.
ONEAF
ALARM SET…
AUX OUT CONTROL…
OUT1
OUT1
OUT2
OUT2
OUT3
OUT3
ON
[PRESET] + [1] + [3] + [6] + [Enter]
[PRESET] + [1] + [3] + [7] + [Enter]
[PRESET] + [1] + [3] + [8] + [Enter]
[PRESET] + [1] + [3] + [9] + [Enter]
[PRESET] + [1] + [4] + [0] + [Enter]
[PRESET] + [1] + [4] + [1] + [Enter]
OFF
ON
OFF
ON
OFF
OTHER SET…
PROPORTIONAL P/T
PROPORTIONAL P/T
TURBO P/T
ON
[PRESET] + [1] + [4] + [2] + [Enter]
[PRESET] + [1] + [4] + [3] + [Enter]
[PRESET] + [1] + [4] + [4] + [Enter]
[PRESET] + [1] + [4] + [5] + [Enter]
[PRESET] + [1] + [4] + [6] + [Enter]
[PRESET] + [1] + [4] + [7] + [Enter]
OFF
ON
TURBO P/T
OFF
ON
AUTO FLIP
AUTO FLIP
OFF
[PRESET] + [1] + [4] + [8] + [Enter]
[PRESET] + [1] + [4] + [9] + [Enter]
[PRESET] + [1] + [5] + [0] + [Enter]
AUTO RETURN *1)
AUTO CAL.
CAM RESET
Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall
be applied to the MENU setup process.
1) The use of AUTO RETURN will be available only when the function
equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.
3-30
3-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Product specifications
SCC-C6403P
Cautions
NO
Items
Contents
- Zoom lens single body SmartDome CAMERA
- AC 24 10% (50Hz 0.3Hz)
- 18W
Remark
1
Product Type
Power Input
• The copyright of the manual belongs to Samsung Electronics Co., Ltd.
2
Power Consumption
3
•
Without the permission of Samsung Electronics it cannot be reproduced
electronically, mechanically, audibly, or by any other method.
4
Broadcasting Type
Image Device
- PAL STANDARD COLOR SYSTEM
- 1/4 inch 410K IT Type S-HAD CCD
- 752(H) X 582(V)
5
•
This manual will be modified according to product enhancements.
6
Effective Pixels
Scanning Mode
7
- 625 Lines, 2:1 Interlace
Scanning line
Frequency
- Horizontal : 15,625 Hz(INT) / 15,625 Hz(L/L)
- Vertical : 50 Hz(INT) / 50 Hz(L/L)
8
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
9
Synchronization Mode
- INT/LINE LOCK
- 480 TV LINES
10
11
Resolution
S/N Ratio
- 50dB (AGC OFF)
(Applicable in the European Union and other European countries with
separate collection systems)
- COLOR : 0.3 Lux (30 IRE : Sense-Upx4)
0.01 Lux (30 IRE : Sense-Up x128)
- B/W : 0.03 Lux (30 IRE : Sense-Upx4)
0.001 Lux (30 IRE : Sense-Up x128)
Min. Object Illumination
12
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
- ATW1/ATW2/AWC/MANUAL MODE
(3200K, 5600K, R/B GAIN Court)
Color Temperature
Signal Output
13
14
-
COMPOSITE VIDEO OUT : 1.0Vp-p 75ohms/BNC
- one body; 32x Zoom lens
- Focal Length : 3.55 to 113 mm
- Aperture : F1.69(Wide), F4.17(Tele)
- MOD(Minimum Object Distance) : 2.5m
15
Lens
- PAN range : 350° Non-Endless
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
16
17
18
PAN Function
TILT Function
- Preset Pan Speed : max 400°/sec
- Manual Pan Speed : 0.1°~180°/sec (64step)
- TILT range : 0°~90°
- Preset TILT Speed : max 200°/sec
- Manual TILT Speed : 0.1°~90°/sec (64step)
Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
- ZOOM(TELE/WIDE), FOCUS(NEAR/FAR),
IRIS(OPEN/CLOSE), PAN/TILT, MENU
RS-485 HALF/FULL Duplex, RS-422
REMOTE
CONTROL
- Alarm Inputs : 4 IN(5mA Sink)
- Alarm Outputs : 3 OUT (Open collector : 2
DC24V 40mA Max, Relay : 1, NO, NC, COM
2A 30VDC, 0.5A 125VAC Max)
ALARM
19
- 10°C ~ +50°C
20
21
Operation Temperature
Operation Humidity
- ~90%
- DOME : 147 (ø),
22
23
24
SIZE
- Outline : 159.6(ø) X 177(H)
- 1.8Kg
Weight
4.5 Years
Lives of Main Parts - FAN
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
|