Professional Security LCD Monitor
INSTRUCTION MANUAL
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
•
•
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514
TEL : +82-31-740-8137~8141 FAX : +82-31-740-8145
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey KT16 OPS
STM-19LV/17LV
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325
About this manual
VAN 06. 03
Please read this manual carefully before installing and using the camera. Be sure to keep the manual handy for later reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER
MANUAL
USER
MANUAL
FCC RF INTERFERENCE STATEMENT
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or
manufacturer could void the users authority to operate such equipment.
CAUTION
The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed
near the equipment and is easily accessible.
CAUTION TO SERVICE PERSONNEL
• DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set
out in the radio interference regulation of Canadian Department of communications.
POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT.
UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING.
CONNECTING WITH EXTERNAL EQUIPMENT
CAUTIONS
• NEVER REMOVE THE BACK COVER
A. BOTTOM PANEL CONTROL
Removal of the back cover should be carried out only by qualified personnel.
1
2
3
4
5
6
7
8
9
10
11
• DO NOT USE IN HOSTILE ENVIRONMENTS
To prevent shock or fire hazard, do not expose the unit to rain or moisture. This unit is designed to be used in
the office or home. Do not subject the unit to vibrations, dust of corrosive gases.
• KEEP IN A WELL VENTILATED PLACE
Ventilation holes are provided on the cabinet to prevent the temperature from rising. Do not cover the unit or
place anything on the top of unit.
VCR
CAMERA A
CAMERA B
DVR
• AVOID HEAT
Avoid placing the unit in direct sunshine or near a heating appliance.
• TO ELIMINATE EYE FATIGUE
1. DC 12V IN
2. D-SUB IN : PC Signal Input
3. VIDEO 1(AV1) IN : Composite signal Input for AV1
Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly
on the monitor.
4. VIDEO 1(AV1) OUT : Video looping output for AV1
5. VIDEO 2(AV2) IN : Composite signal Input for AV2
6. VIDEO 2(AV2) OUT : Video looping output for AV2
7. AUDIO 1 IN : Stereo Audio Signal Input, This input is for AV1, S-VIDEO
8. AUDIO 2 IN : Stereo Audio Signal Intput, This Output is for AV2
9. S-VIDEO (Y/C) IN : Y/C separated signal input
• BE CAREFUL OF HEAVY OBJECT
Neither the monitor itself nor any other heavy object should rest on the power cord. Damage to a power cord
can cause fire or electrical shock.
10. S-VIDEO (Y/C) OUT : Y/C separated signal looping output 11. PC STEREO IN
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USER
MANUAL
USER
MANUAL
7. IR Sensor
Remote controller sensor.
REMOTE FUNCTIONS
8. POWER ON/OFF(
)
1
Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED
(next to the power switch) lights with green when the power is turned ON. The power is turned off by
pressing the power switch again and the power LED goes Red.
B. REMOTE CONTROLLER
2
1. POWER( ) :
Turns the power ON or OFF.
There will be a few seconds delay before the display appears.
3
• SELF-TEST DISPLAY
2. SOURCE :
When there is no connection at PC, the On Screen Display will show
for 3 seconds.
Select pc or video(PC / AV1 / AV2 / S-Video) sources.
5
4
8
3. MUTE : Mute the sound.
6
7
4. MENU : Activates and exits the On Screen Display.
5. VOL(
Increases or decreases the level of audio volume.
6. UP/DOWN( ) : Move to OSD menu.
) :
• OSD MENU DESCRIPTION
Input Source : Select PC or AV1, SVIDEO.
7. AUTO : Auto geometry adjustment in PC Source.
8. EXIT : Exit the On Screen Display.
Screen :
CONTROLS AND FUNCTIONS
Brightness - Increase or decrease the intensity of the image.
Contrast - Increase or decrease the intensity(lightness or
dimness) of the image.
H. position(PC Mode Only) - Move image horizontally on screen
right or left.
V. position(PC Mode Only) - Move image vertically on screen
up or down.
1
2
3
4
5
6
7
8
Clock(PC Mode Only) - Adjust the vertical noise of screen image.
• Front Key Control
Phase(PC Mode Only) - Adjust the number of horizontal picture elements.
1. SOURCE
Select input source, and move the previous menu.
2. MENU
Audio
Volume : Adjust audio volume.
Activates and exits the On Screen Display. This button can also be used to move previous menu or status.
OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit.
3/4. DOWN / UP
This button allows user to enter the sub-menu of the activated function. when down key is pressed on the
main menu.
5/6. VOL< / VOL >
Adjust the volume / Adjust menu settings.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USER
MANUAL
USER
MANUAL
OSD :
MOUNTING GUIDE
H. Position - Move the OSD position to right( ) or left( ).
V. Position - Move the OSD position to up( ) or down( ).
Transparency - Select the OSD background.
Wall mountable using two methods:
1) Using the 200 mm pre-cut holes
2) Using the VESA standard wall mount design and the 100mm hole pattern on the back panel to install the LCD
monitor to the wall.
OSD Timer - Select the OSD display timing.
Language - Select a language among
English, Français, Deutsch, Español, Danish, Italiano.
Color (PC Mode) :
Wall
Color Temp - Adjust color temperature to 9300, 6500, user.
(note : 9300 is factory default)
Pad
Arm
Red - Adjust red color for user.
Green - Adjust green color for user.
Blue - Adjust blue color for user.
Monitor
D-SUB CONNECTOR PIN ASSIGNMENTS
• PIN ASSIGNMENTS
Utility :
Recall - Select to reset all setting to the factory default values.
Lock - Select ON or OFF
(ON : Control key lock. OFF : Control key unlock)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
RED VIDEO
Pin 9
GREEN VIDEO
BLUE VIDEO
GROUND
Pin10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
SIGNAL CABLE DETECT
GROUND
SAD(for DDC)
D-SUB
GROUND
H-SYNC.(or H+V SYNC.)
V-SYNC
RED GROUND
GREEN GROUND
BLUE GROUND
Exit : Turn off OSD Menu.
SLC(for DDC)
• ACCESSORY
1. POWER CORD
5. Remote Control
2. USER’S MANUAL
6. Batteries
3. PC cable
7. Wall mount (Option)
4. Adaptor
8. Rack mount (Option)
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USER
MANUAL
USER
MANUAL
POWER MANAGEMENT
SPECIFICATIONS
This monitor features a power management system to “power down” upon receipt of the VESA DPMS(The
display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card
performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an
appropriate mode through identifying each of the three modes of the signaling system.
Model Name
Composite
STM-19LV
STM-17LV
2ch input 1.0Vp-p, 75Ω terminated, loop-through out
1ch input (Y/C), loop-through out
1ch input
Video
S-VIDEO
VGA
Resolution
Frequency
1280x1024@60Hz
Horizontal(KHz)
Vertical(Hz)
31KHz ~ 82KHz
• POWER CONSUMPTION
50Hz ~ 77Hz
720x480@60Hz, 720x576@50Hz, 800x600@60/75Hz
1024x768@60/75Hz, 1280x1024@60/75Hz
Max. 42W
MODE
ON
POWER CONSUMPTION
MODE
SUSPEND
ACTIVE OFF
POWER CONSUMPTION
VGAMode
<50W
<5W
<5W
<5W
Power Consumption
Dimensions
(WxDxH)
Max. 36W
Net
Packing
Net Weight
Gross Weight
STANDBY
430x428x200mm
490x506x225mm
6.61Kg
382.4x390.5x200mm
436x476x225mm
5.96Kg
Weight(kg)
• LED INDICATOR
8.43Kg
7.67Kg
Power Supply
DC 12V / 4A
50˚F~104˚F (10˚C~4˚C)
10%~80%, Non-condensing
-4˚F~113˚F (-20˚C~45˚C)
5%~95%,Non-condensing
The power management feature of the monitor is comprised of four stages : On(Green), Standby, Suspend,
Active off(Red & Green) and Unsupported mode(Green).
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Size
Active Display Area
Pixel Pitch(mm)
Brightness(cd/m2)
Contrast Ratio
Environmental
Considerations
MODE
ON
STANDBY
SUSPEND
ACTIVE OFF
UNSUPPORTED MODE
POWER OFF
LED COLOR
MONITOR OPERATION
GREEN
Normal Operation
19" Diagonal AM-TFT
376.32x301.056mm
17" Diagonal AM-TFT
337.92x270.336mm
Screen blanks after preset ide time and some electronic circuits or all
circuitry in the monitor shutdown.
AMBER
0.294mm(H) x 0.294mm(V)
0.264mm(H) x 0.264mm(V)
LCD Panel Spec
300cd/m2
700:1
8ms
GREEN
RED
Normal operation but the on screen display will show error massage.
Not opreation
Response Time(ms)
Viewing Angle(L/R/ T/B)
75/75/75/60
TROUBLESHOOTING GUIDE
DIMENSION
TROUBLE
TROUBLESHOOTING TIP
No image on display screen
1. Check that power cord of the monitor have been connected securely
into wall outlet or grounded extension cable or strip.
STM-19LV
STM-17LV
2. Power switch should be in the ON position and LED is lit.
3. Check that the Brightness and / or the Contrast adjustments of the Display haver not
been turned down to minimum levels.
“Check Input Signal” message on
screen
1. The signal cable should be completely connected to the video card / computer
2. The video card should be completely seated in its slot and the computer is
switched ON.
Display image is not centered, too small
or toolarge in PC mode
Push the down key in front side or Auto key in remocon.
Adjust Clock and Phase in the OSD.
Vertical or Horizontal noise is
present in the picture
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|