Samsung Car Video System 305TPLUS User Guide

LCD-Monitor

Chassis LHU30BS

Model 305TPLUS

Manual

SERVICE

LCD Monitor

Fashion Feature

- Back Side cable management

- Silm / Narrow Design

- PCB: 2 Layer, 150mm x 100mm

- Connectivity: DVI-D, USB 2.0 (1up, 4down)

- Power consumption: 130W

- Built in power supply

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Alignments and Adjustments

This section of the service manual explains how to use the RS232 JIG.

This function is needed for AD board change and program memory (IC200) change.

3-1 Required Equipment

The following equipment is necessary for adjusting the monitor:

Computer with Windows 95, Windows 98, or Windows NT.

MTI-2055 DDC MANAGER JIG

3-2 DDC EDID Data Input

1. Input DDC EDID data when replacing AD PCB.

2. Receive/Download the proper DDC file for the model from HQ quality control department.

Install the below jig (Figure 1) and enter the data.

MTI-2055

DDC Manager

Parallel Connector

(25P Cable)

Connect Monitor

(Signal Cable)

Figure 1.

3-3 Hidden Key list

3-1

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Alignments and Adjustments

3-4 EDID Installation with Dos Program

1.Execute "DDC21.exe"±

2.Click "LOAD FILE"±

3.File Name "305T.DDC"

4. Click "WRITE EEPROM"±

Confirm the "OK" Sign

Error Massage: Check the Signal Cable

or Interface Board

3-2

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Alignments and Adjustments

3-5 EDID Installation with Windows Program

1. Execute "WinDDC.exe"

2. Click "Sys Config"±

Select "Station : Write station".

Check "Serial No and Week : Don't change"±

Click "Save"±

3. Click "Open" icon.

Select "Connected Port #1" and Next "OK".

* File Name - 305T.DDC

Press enter key on your keyboard.

4. Confirm the "DDC OK".

- After Replacing the Main Board

-EDID Installation (Analog and Digital)

-Factory Reset(Using Power key)

During Power off, press Power key for 5 seconds.

With 1 beep sound, Factory Reset executes.

3-3

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Alignments and Adjustments

Memo

3-4

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Block Diagrams

7 Block Diagram

7-1 Block Diagram (Main)

7-1

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Block Diagrams

7-2 Block Diagram (SMPS)

7-2

Download from Www.Somanuals.com. All Manuals Search And Download.

13 Circuit Descriptions

13-1 BLOCK discription (MAIN)

13-1

Download from Www.Somanuals.com. All Manuals Search And Download.

13 Circuit Descriptions

BLOCK

MICOM

USB

DESCRIPTION

NAME

WT61P4

IC-MICROCONTROLLER,PLCC,44P,16Bit

USB2504

SI4435

IC-USC, USB2504,8Bit,TQFP,64P

FET-SILICON, SI4435DY,P,-30V,+-8.0A,

0.014ohm,2.5W,SO-8

DC/DC

CN_DSUB_24_3R_G2, CONNECTOR-DVI,

24P,3R,FEMALE,ANGLE,AUF

DVI-D INPUT

CONNECTOR-DVI

USB_DN

JACK_USB_08_G4, JACK-USB, 4P/2C,AUF,

BLK,ANGLE,A TYPE

USB PORT

JACK_USB_04_G2, JACK-USB, 4P/1C,AU,IVR,

ANGLE,B TYPE

USB_UP

SIGNAL

CONNECTOR

CN_SMD_S_030, CONNECTOR-HEADER,

BOX,30P,1R,1.25mm,SMD-A,Sn+Pb,IVR

LVDS CONNECTOR

DATA CONNECTOR

POWER CONNECTOR

CN_S_015_G2, CONNECTOR-HEADER,

BOX,15P,1R,1.25mm,SMD-A,SnPb,IVR

DATA

CONNECTOR

CN_S_016, HEADER-BOARD TO CABLE,

BOX,16P,1R,2mm,ANGLE,SN,IVORY

POWER

CONNECTOR

CN_S_006_G2, CONNECTOR-HEADER,

BOX,6P,1R,1.25mm,SMD-A,SnPb,IVR

FUNCTION

CONNECTOR

FUNCTION

CN_S_014,HEADER-BOARD TO CABLE,

BOX,14P,1R,2mm,ANGLE,SN,IVORY

INVERTER

CONNECTOR

inverter

connector

13-2

Download from Www.Somanuals.com. All Manuals Search And Download.

13 Circuit Descriptions

13-2 BLOCK discription (SMPS)

13-3

Download from Www.Somanuals.com. All Manuals Search And Download.

13 Circuit Descriptions

BLOCK

EMI Filter

DESCRIPTION

NAME

LX801s

FP801S

Coil Line filter

Inrush current

For continued protection

Power Factor Correction (PFC) allows power distribution to

operate at its maximum efficiency

PFC section

PFC Circuit

M-power

STD 6V

Multiple-chip power Device

F9222L

Standby power is the power consumed by an appliance during

the lowest possible electricity consuming mode

Standby power

Rectifier &

Filtering

Rectification is the conversion of alternating current (AC) to

direct current (DC).

13-4

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the 305TLCD monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

11-1 Disassembly

Cautions: 1. Disconnect the monitor from the power source before disassembly.

Description

Picture Description

1. Place monitor face down on cushioned table.

Remove 4 screws and lift up the Stand ass'y

2. Lift up the stand cover from front cover

11-1

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Disassembly and Reassembly

Description

Picture Description

3. Disconnect cables and remove the inverter

power and function cable

4. Remove 1screws from the Shield.

5. Remove 4screws from the Shield between

LCD_psanel and Shield

6. Disconnect cables LVDS and Signal from Panel

control board

11-2

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Disassembly and Reassembly

Description

Picture Description

7. Remove 2screws from DVI input connector

8. Up and down the chassis ass'y

9. Remove 2 screw on the main board

10.Remove 3 screws on the SMPS board

11-3

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Disassembly and Reassembly

Description

Picture Description

11.Disconnect cables LVDS and Signal and Power

from Main board

11-3 Reassembly

Reassembly procedures are in the reverse order of disassembly procedures.

11-4

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

You can search for updated part codes through ITSELF web site.

URL : http://itself.sec.samsung.co.kr/

6-1. LS30HUXCB/XSF Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

LS30HUXCB/XSF

305TPLUS,WQA1/S30A0-LHU,30,LCD-MO,CHINA

0.1

..2

M0001

T0003

M0112

T0022

T0054

M0145

T0382

BN90-01014G

BN96-03652F

BN63-02663D

BN64-00504A

BN64-00505A

BN96-04050A

BP61-00495C

ASSY COVER FRONT;LS30HUX_305T PLUS

S.N.A

S.A

ASSY COVER P-FRONT;LS30HUX(305T PLUS),,H

COVER-FRONT;LS30HUX (305T PLUS),HIPS HB

KNOB-CONTROL;HUBBLE,HIPS HB,T2.0,UT-0510

KNOB-DECORATION;HUBBLE,ABS HB,T2.0,NATUR

ASSY BOARD P-FUNCTION;HUBBLE,SJ06-01-013

HOLDER-CARE;PJT,ACRYL-FOAM,T0.25,W30.0mm

...3

..2

S.N.A

S.A

0.2

S.N.A

0.1

..2

M0002

M0013

M0006

BN90-01015A

BN96-03991A

BN63-02664A

ASSY COVER REAR;LS30HUBCB/XAA

S.N.A

S.A

ASSY COVER P-REAR;HUBBLE,,HIPS HB,,BK26,

COVER-REAR;HUBBLE,HIPS HB,3.2,BK26

...3

S.N.A

0.1

..2

M0216

M0003

T0081

M0081

HC+CW

CIS4

BN90-01194C

BN96-04718B

6001-001547

6003-000275

6003-001119

6009-001370

BN61-01438A

BN61-02570A

BN61-02572A

BN61-02575A

BN61-02576A

BN61-02581A

BN61-02634A

BN61-03118A

BN63-02666A

BN63-02668A

BN63-02669A

BN63-02670A

BN63-02671A

BN63-02672A

BN63-03079A

BN63-03082A

BN73-00085A

BN96-01524C

BN96-05623A

BN96-04908C

BN73-00077A

ASSY STAND;LS30HU

S.N.A

S.A

ASSY STAND P;-,HUBBLE27,-,HIPS HB,BK26,L

SCREW-MACHINE;BH,+,M4,L10(5),ZPC(BLK),SW

SCREW-TAPTITE;BH,+,-,B,M3,L10,ZPC(BLK),S

SCREW-TAPTITE;FH,+,-,S,M4,L10,ZPC(BLK),S

SCREW-SPECIAL;PWH,+,-,M4,L8,ZPC(WHT),SWR

HOLDER-STAND;MATISSE HAS-STAND,SWRCH18A

BRACKET-STAND BOTTOM;HUBBLE,SECC,3.0

BRACKET-STAND BOTTOM;HUBBLE,ALDC

BRACKET-STAND BODY;HUBBLE,SECC,T2.0

BRACKET-STAND LIFT;HUBBLE,SECC,2.0

HOLDER-SWIVEL RING;HUBBLE,ACETAL,2.5

GUIDE-STAND RETAINER;HUBBLE,ACETALl,T2.0

GUIDE-STAND LIFT;HUBBLE 27",ACETAL

...3

S.A

S.N.A

M0174

M0412

COVER-STAND TOP;HUBBLE,ABS HB,2.5,BK26

COVER-STAND LIFT FRONT;HUBBLE,HIPS HB,2.

COVER-STAND LIFT REAR;HUBBLE,HIPS HB,2.5

COVER-STAND LIFT FRONT;HUBBLE,HIPS HB,2.

COVER-STAND LIFT REAR;HUBBLE,HIPS HB,2.5

COVER-SWIVEL BASE;HUBBLE,HIPS HB,2.5,BK2

COVER-STAND VESA;HUBBLE27",ABS HB,2.8,BK

COVER-STAND BASE;HUBBLE27",ABS HB,2.8,BK

RUBBER CUSHION;MATISSE,##4.5(IN SIDE),CL

ASSY STAND P-STOPPER;-,HUBBLE30",-,SUS,-

ASSY STAND P-SPRING;-,HUBBLE 30",-,SUS,B

ASSY HINGE P;HUBBLE,SK5,T2.0,275T

T0004

T0081

M0007

M0126

T0054

T0132

RUBBER FOOT;MATISSE,BUMPON,##13.5,T2.0,6

0.1

..2

M0017

M0081

M0014

CN102

CN330

CN821

CN801

BN91-01124A

6003-000282

6003-001439

BN94-01009S

3701-001173

3711-000057

3711-005955

3722-001101

3722-001414

ASSY CHASSIS-SPZ,W/W;LS30HUB*

S.N.A

S.A

SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW

SCREW-TAPTITE;BH,+,-,S,M4,L8,ZPC(WHT),SW

ASSY PCB MAIN-SPZ,W/W;LS30HUB*

..2

S.A

..2

S.N.A

S.A

..2

...3

CONNECTOR-DVI;24P,3R,FEMALE,ANGLE,AUF

HEADER-BOARD TO CABLE;BOX,3P,1R,2.5MM,AN

HEADER-BOARD TO CABLE;BOX,16P,1R,2mm,ANG

JACK-USB;4P/1C,AU,IVR,ANGLE,B TYPE

S.A

JACK-USB;4P/2C,AUF,BLK,ANGLE,A TYPE

S.A

6-1

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

...3

CN802

T0174

SUB05

D100

D101

D102

D103

D104

D105

D106

D107

D116

D117

D118

D119

D120

D121

D821

D822

D0254

D115

ZD104

ZD106

ZD108

ZD801

ZD802

ZD803

ZD804

D802

D804

ZD107

ZD200

Q101

Q401

Q404

Q812

Q409

T0596

IC112

T0087

P803T

R110

3722-001414

JACK-USB;4P/2C,AUF,BLK,ANGLE,A TYPE

S.A

S.N.A

S.A

...3

BN97-01026Z

0202-001477

0401-001056

0402-000553

0403-000258

0403-001411

0403-001435

0406-001061

0501-002080

0505-000110

0505-001957

0904-001972

1103-000129

1103-001314

1203-002842

1404-001223

2007-000060

2007-000070

ASSY SMD;LS30HUB*

1.048

....4

SOLDER-CREAM;LST309-M,-,D20~45##,96.5Sn/

DIODE-SWITCHING;MMBD4148SE,100V,200mA,SO

DIODE-SCHOTTKY;SS24/B240,40V,2000mA,DO-2

DIODE-ZENER;BZX84C5V6,5.2-6V,225mW,SOT-2

DIODE-ZENER;-,5.49-5.73V,200mW,SOD-323,T

DIODE-ZENER;QZX363C5V6,5.32-5.88V,200MW,

DIODE-TVS;MMQA5V6T3,5.32/5.6/5.88V,24W,S

TR-SMALL SIGNAL;2SC2412K,NPN,200mW,SC-59

FET-SILICON;2N7002,N,60V,115mA,7.5ohm,0.

FET-SILICON;NTR2101P,P,-8V,-3.7A,0.052oh

IC-USC;USB2504,8Bit,TQFP,64P,10x10x1.4mm

IC-EEPROM;24C02,2Kbit,256x8Bit,SOP,8P,5x

IC-EEPROM;24C16,2Kx8,SOP,8P,5x4mm,2.7/5.

IC-POSI.FIXED REG.;AP1117D-33A,TO-252,3P

THERMISTOR-PTC;45mohm,20,6V,-,40A,4A,TP

R-CHIP;100Kohm,1%,1/10W,TP,1608

R-CHIP;0ohm,5%,1/10W,TP,1608

6-2

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

....4

R110

2007-000070

R-CHIP;0ohm,5%,1/10W,TP,1608

S.A

2007-000070

2007-000071

2007-000074

R-CHIP;0ohm,5%,1/10W,TP,1608

R-CHIP;22ohm,5%,1/10W,TP,1608

R-CHIP;100ohm,5%,1/10W,TP,1608

6-3

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

....4

R110

2007-000074

R-CHIP;100ohm,5%,1/10W,TP,1608

S.A

2007-000074

2007-000075

2007-000076

2007-000078

2007-000083

2007-000084

R-CHIP;100ohm,5%,1/10W,TP,1608

R-CHIP;220ohm,5%,1/10W,TP,1608

R-CHIP;330ohm,5%,1/10W,TP,1608

R-CHIP;1Kohm,5%,1/10W,TP,1608

R-CHIP;3Kohm,5%,1/10W,TP,1608

R-CHIP;4.7Kohm,5%,1/10W,TP,1608

6-4

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

....4

R110

C120

2007-000084

R-CHIP;4.7Kohm,5%,1/10W,TP,1608

S.A

2007-000084

2007-000090

2007-000091

2007-000093

2007-000102

2007-000109

2007-000119

2007-000570

2007-001002

2203-000189

2203-000236

2203-000257

2203-000426

R-CHIP;4.7Kohm,5%,1/10W,TP,1608

R-CHIP;10Kohm,5%,1/10W,TP,1608

R-CHIP;12Kohm,5%,1/10W,TP,1608

R-CHIP;20Kohm,5%,1/10W,TP,1608

R-CHIP;100Kohm,5%,1/10W,TP,1608

R-CHIP;1Mohm,5%,1/10W,TP,1608

R-CHIP;560ohm,5%,1/10W,TP,1608

R-CHIP;220OHM,1%,1/10W,TP,1608

R-CHIP;510ohm,5%,1/10W,TP,1608

C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608

C-CER,CHIP;0.1nF,5%,50V,C0G,1608

C-CER,CHIP;10nF,10%,50V,X7R,TP,1608

C-CER,CHIP;0.018nF,5%,50V,C0G,1608

6-5

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

6-2 LS17VDP Others

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

....4

C120

C846

C411

C400

C404

2203-000426

C-CER,CHIP;0.018nF,5%,50V,C0G,1608

S.A

2203-000426

2203-000440

2203-005005

2203-005065

2203-005249

2203-005261

2203-005437

2402-001033

2402-001079

2402-001081

C-CER,CHIP;0.018nF,5%,50V,C0G,1608

C-CER,CHIP;1nF,10%,50V,X7R,1608

C-CER,CHIP;100nF,10%,16V,X7R,1608

C-CER,CHIP;1000nF,+80-20%,10V,Y5V,1608

C-CER,CHIP;100nF,10%,50V,X7R,1608

C-CER,CHIP;1000nF,10%,25V,X7R,3216

C-CER,CHIP;10000nF,+80-20%,10V,Y5V,3216

C-AL,SMD;220uF,20%,16V,GP,TP,8.3x8.3x10

C-AL,SMD;100uF,20%,35V,WT,TP,10.3x10.3x1

C-AL,SMD;100uF,20%,25V,WT,TP,8.3x8.3x10

6-6

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

....4

.....5

....4

...3

C600

2402-001081

C-AL,SMD;100uF,20%,25V,WT,TP,8.3x8.3x10

S.A

C611

2402-001081

2402-001128

2402-001254

2409-001065

2801-003326

3301-001145

3301-001412

3301-001594

BN41-00768A

BN97-01071L

0903-001397

1203-001559

0406-001217

3711-005470

3711-005497

3711-005543

2007-000512

0505-002169

3711-004121

0202-001608

BN96-03656A

BN63-02673A

AA61-20129A

BN63-00647A

BN63-02969A

BN63-02970A

BN63-02971A

BN63-02972A

BN63-02973A

BN63-02975A

AA61-20069A

C-AL,SMD;100uF,20%,25V,WT,TP,8.3x8.3x10

C-AL,SMD;100##F,20%,16V,-,TP,6.3X5.7mm

C-AL,SMD;10uF,20%,50V,WT,TP,6.3x5.2mm

C-ORGANIC;82uF,20%,16V,WT,TP,8X6.9mm,-

CRYSTAL-SMD;24MHZ,30PPM,28-ABX,20PF,50OH

BEAD-SMD;60ohm,4516,TP,70ohm/45MHz,82ohm

BEAD-SMD;60ohm,2012,800mA,TP,65ohm/110MH

BEAD-SMD;90ohm,2.0*1.2*1.3mm,-,TP,-,-,-

0.003

C614

S.A

C605

S.A

C120

S.A

C608

S.A

C842

S.A

C844

S.A

X202

S.A

X202

S.A

T0568

T0077

MICOM

IC520

IC202

D801

S.N.A

S.A

BEAD-SMD;90ohm,2.0*1.2*1.3mm,-,TP,-,-,-

PCB MAIN;Hubble,FR-4,2L,1.0,1.6,150*100,

ASSY MICOM-SPZ,W/W;LS30HUB*,W/W

IC-MICROCONTROLLER;WT61P4,8Bit,PLCC,44P,

IC-RESET;DS1834A,SOIC,8P,150MIL,PLASTIC,

DIODE-TVS;NUP4301MR6,6/-/-V,500W,TSOP-6

HEADER-BOARD TO CABLE;BOX,30P,1R,1.25mm,

HEADER-BOARD TO CABLE;BOX,15P,1R,1.25MM,

HEADER-BOARD TO CABLE;BOX,6P,1R,1.25mm,S

R-CHIP;2.4Kohm,5%,1/10W,TP,1608

S.N.A

S.A

D803

S.A

CN330

R110

S.A

Q409

FET-SILICON;Si4435BDY-T1-E3,P,-30V,-9.1A

HEADER-BOARD TO BOARD;BOX,14P,1R,2mm,ANG

SOLDER-WIRE FLUX;LFC7-107,D0.8,99.3Sn/0.

ASSY SHIELD P-COVER;HUBBLE,SECC,T0.8

SHIELD-COVER;HUBBLE,SECC,0.8

S.N.A

S.A

Q409

CN402

T0245

M0006

M0107

M0114

M0131

M0114

...3

S.N.A

..2

...3

HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,DAFC-25

GASKET;GH19BS,CONDUCTIVE FAB,0.3MM,20MM,

GASKET;GASKET EMI,Polyurethane Sponge+Po

HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,V0,PAWH

...3

6-7

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Electrical Parts List

Level

Loc. No.

Code No.

Description & Specification

Q'ty

SA/SNA

..2

...3

..2

...3

..2

M2893

T0297

T0159

MP1.0

T0514

M0131

M0251

T0081

BN39-00482B

LEAD CONNECTOR;HUBBLE,UL2835#28,UL/CSA,1

S.A

BN39-00753A

BN96-03938A

BN96-04386A

BN61-02582A

BN63-02967A

BN63-02969A

BN96-04422A

6006-000245

BN96-04553A

BN63-03046A

BN63-03064A

6046-001013

BN73-00174A

CABLE FORM CONN.COAX-TMDS HARN;HUBBLE,UL

ASSY PCB P-SMPS;FreeVoltage SMPS,Hubble3

ASSY BRACKET P-GUIDE POWER;-,HUBBLE30",-

BRACKET-SUPPORT;HUBBLE,SPTE,0.3

S.A

S.N.A

S.A

GASKET;GASKET EMI,Polyurethane Sponge+Po

ASSY CABLE P;HUBBLE,SEC VD DIVISION,WORL

SCREW-MACHINE;PH,+,WSP,M4,L8,ZPC(WHT),SW

ASSY SHIELD P-EMI;HUBBLE30",SECC,T0.8

GASKET-SHIELD;HUBBLE30",SECC,T0.8

S.N.A

T0528

M0131

T0562

CCMM1

GASKET;HUBBLE,Polyurethane Sponge+Polyes

STAND OFF;M3,L5,Ni PLT,SUM24L,#4-40

SILICON/RUBBER;HUBBLE,GP1500,60x30x5,k=1

0.1

..2

M0112

M0081

BN91-01139A

6003-000282

6003-001439

BN96-04387A

BN63-02674A

BN63-02966A

BN63-02968A

BN63-03264A

BN39-00757A

0203-002475

ASSY SHIELD;LS30HUBCB/XAA

S.N.A

S.A

SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW

SCREW-TAPTITE;BH,+,-,S,M4,L8,ZPC(WHT),SW

ASSY BRACKET P-CASE TOP;-,HUBBLE30",-,SP

SHIELD-CONNECTOR;HUBBLE,SPTE,0.3

GASKET;GASKET EMI,Polyurethane Sponge+Po

GASKET;LS27HUB(HUBBLE 27"),Fabric Gasket

LEAD CONNECTOR;HUBBLE,UL1007#26,UL/CSA,1

TAPE-AL;DK-100-360-93-1S,AL-Foil, Flame

..2

S.N.A

S.A

..2

...3

..2

M0131

M2893

CIS1

..2

S.N.A

0.1

..2

T0852

M0215

BN91-01858A

BN07-00470A

ASSY LCD-SPZ;LS30HUX*

S.N.A

S.A

LCD-PANEL;LTM300M1-P02,Hubble,8BIT,677.3

0.1

..2

M0113

T0376

T0003

M0081

T0524

BN92-01751Z

6902-000061

6902-000379

6902-000604

6902-000609

6902-000410

ASSY P/MATERIAL;LS30HUUBCB/XAA

S.N.A

BAG AIR;LDPE,T0.2,L1000,W500,TRP,,,

0.003

0.007

5.75

0.135

BAG AIR;LDPE,T0.2,W1000,L1800,TRP,-,--

BAG WRAPPING;LDPE,T0.02,W500,L10000,TRP,

BAG ROLL;LDPE,T0.05,W2400,L1000,TRP,-,-

BAG PE;HDPE/NITRON,T0.015/T0.5,W850,L800

0.1

M0019

BN92-02330V

ASSY LABEL;LS30HUBCB/XSF

S.N.A

0.1

..2

M0003

M0045

BN92-02989E

BN69-02102B

ASSY BOX;LS30HUXCB/XSF,305TPLUS

S.N.A

BOX-MONITOR;LS30HUB(S/M305T Plus),CB,A1,

1.01

0.1

..2

M0045

T0725

T0299

M0045

T0268

T0524

M0113

BN92-02999B

BN39-00397C

BN39-00754A

BN96-06367C

3903-000082

6902-000110

BH68-70455A

ASSY ACCESSORY;LS30HUXCB/XSF

S.N.A

S.A

CBF INTERFACE-USB;SPL-07,4P/4P,2725(USB2

CBF SIGNAL-DVI-D DUAL LINK;HUBBLE,24P/24

ASSY ACCESSORY;LS30HUXCB/XSF

..2

S.A

..2

S.A

...3

....4

...3

....4

CBF-POWER CORD;DT,CN,IP3/YES(A),I(IEC C1

BAG PE;LDPE,T0.05,W250,L400,TRP,28,2

S.A

S.N.A

CARD-TESTED GOODS;ALL (CHINA),SAMAUNG,CH

UNIT-11,WARRANTY;CHINA,-,ASS'Y-W/CARD,BH

MANUAL FLYER-11,WARRANTY CARD;SAMSUNG BA

MANUAL FLYER-10,WARRANTY CARD;ENVELOPE,S

MANUAL-02,TCO99 CARD;COMM,W/W,Mojo 100g,

ASSY MANUAL P-IB+QSG;305T,305TPLUS,-,Syn

S/W DRIVER-1,IB;305T,305TPLUS,W/W,SyncMa

MANUAL FLYER-QSG;305T,SyncMaster,Multe,M

ACCESSORY BH75-00146B

CIS

BH68-00297E

BH68-00297F

ACCESSORY BN68-01118A

M0215

BN96-03966N

BN59-00565N

BN68-01073A

QSG

6-8

Download from Www.Somanuals.com. All Manuals Search And Download.

6 Exploded View & Parts List

5 Exploded View and Parts List

-You can search for updated part codes through ITSELF web site.

URL : http://itself. sec. samsung.co.kr

5-1. Exploded View

T0003

M0215

M0145

M0014

M0006

T0514

M0002

M0003

5-1

Download from Www.Somanuals.com. All Manuals Search And Download.

5 Exploded View & Parts List

5-1-1. LS30HUXCB/XSF Parts List

Location

T0003

Code.No

Item & Specification

Q'ty

SA/SNA

S.A

Remark

BN96-03652F

BN07-00470A

BN96-04050A

BN94-01009S

BN96-03656A

BN61-02582A

BN90-01015A

BN96-04718B

ASSY COVER P-FRONT;LS30HUX(305T PLUS),,H

LCD-PANEL;LTM300M1-P02,Hubble,8BIT,677.3

ASSY BOARD P-FUNCTION;HUBBLE,SJ06-01-013

ASSY PCB MAIN-SPZ,W/W;LS30HUB*

M0215

M0145

M0014

M0006

T0514

S.A

ASSY SHIELD P-COVER;HUBBLE,SECC,T0.8

BRACKET-SUPPORT;HUBBLE,SPTE,0.3

ASSY COVER REAR;LS30HUBCB/XAA

ASSY STAND P;-,HUBBLE27,-,HIPS HB,BK26,L

S.N.A

S.A

M0002

M0003

5-2

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Operating Instructions and Installation

10-1 Product Features

0^o(Standard)

Swivle

- Sync & DE(Data Enable) mode

Tilt

- Improved Response Time by Adopting RTA

: 6 ms (Based on "Gray to Gray")

- Dual Link TMDS serial interface (4pixel/clock)

- RoHS compliance

- High contrast ratio & high aperture structure

- High speed response

- Pb-free compliance

- WQXGA (2560 x 1600 pixels) resolution

- S-PVA (Super Patterned Vertical Alignment) mode

- Direct BLU Structure (Cold Cathod Fluorescent

Tube)

- VESA Mount 200 x 100 mm, 100 x 100 mm

10-2 Component & Function

1. Brightness button

Push the button to adjust brightness.

¡ã : The screen is getting bright.

¡å : The screen is getting dark.

2. Power button / Power indicator

Turns the monitor on/off. /

This light glows blue during normal operation, and

blinks blue once as the monitor saves your adjust-

ments.

10-1

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Operating Instructions and Installation

10-3 Installation Instructions

(The configuration at the back of the monitor may vary from product to product.)

1. USB DOWNSTREAM :

Connect the USB DOWN port of the USB monitor and a USB

device with the USB cable.

2. USB UPSTREAM :

nnect the USB UP port of the monitor and the USB port of the

computer with the USB cable.

DVI IN

Connect the DVI-D (Dual link) Cable to the DVI IN port on the

back of your monitor.

1. ON [ | ] / OFF [O]

Switch the monitor on and off.

2. POWER

Connect the power cord for your monitor to the POWER port on

the back of the monitor.

Stand Stopper

Remove the fixing pin on the stand to lift the monitor up and

down.

10-2

Download from Www.Somanuals.com. All Manuals Search And Download.

12 PCB Layout

12 PCB Diagram

12-1 PCB Diagram (Main)

12-1

Download from Www.Somanuals.com. All Manuals Search And Download.

12 PCB Layout

12-2 PCB Diagram (SMPS)

12-2

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Precautions

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock.

1-1 Safety Precautions

1-1-1 Warnings

1. For continued safety, do not attempt to modify the circuit

board.

2. Disconnect the AC power and DC power jack before

servicing.

1-1-2 Servicing the LCD Monitor

1. When servicing the LCD Monitor, Disconnect the AC

line cord from the AC outlet.

2. It is essential that service technicians have an accurate

voltage meter available at all times. Check the

calibration of this meter periodically.

1-1-3 Fire and Shock Hazard

Before returning the monitor to the user, perform the

following safety checks:

Figure 1-1. Leakage Current Test Circuit

1. Inspect each lead dress to make certain that the leads are

4. With the unit completely reassembled, plug the AC line

not pinched or that hardware is not lodged between the

cord directly into a 120V AC outlet. With the unit’s AC

chassis and other metal parts in the monitor.

switch first in the ON position and then OFF, measure

2. Inspect all protective devices such as nonmetallic control

knobs, insulating materials, cabinet backs, adjustment

and compartment covers or shields, isolation resistor-

capacitor networks, mechanical insulators, etc.

the current between a known earth ground (metal water

pipe, conduit, etc.) and all exposed metal parts,

including: metal cabinets, screwheads and control shafts.

The current measured should not exceed 0.5 milliamp.

Reverse the power-plug prongs in the AC outlet and

3. Leakage Current Hot Check (Figure 1-1):

repeat the test.

WARNING : Do not use an isolation

transformer during this test.

1-1-4 Product Safety Notices

Use a leakage current tester or a metering system that

complies with American National Standards Institute

(ANSI C101.1, Leakage Current for Appliances), and

Underwriters Laboratories (UL Publication UL1410,

59.7).

Some electrical and mechanical parts have special safety-

related characteristics which are often not evident from visual

inspection. The protection they give may not be obtained by

replacing them with components rated for higher voltage,

wattage, etc. Parts that have special safety characteristics are

identified by

on schematics and parts lists. A substitute

replacement that does not have the same safety characteristics

as the recommended replacement part might create shock, fire

and/or other hazards. Product safety is under review

continuously and new instructions are issued whenever

appropriate.

1-1

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Precautions

1-2 Servicing Precautions

WARNING:

An electrolytic capacitor installed with the wrong polarity might explode.

Caution:

Before servicing units covered by this service manual, read and follow the Safety Precautions section

of this manual.

Note:

If unforeseen circumstances create conflict between the following servicing precautions and any of the safety

precautions, always follow the safety precautions.

1-2-1 General Servicing

Precautions

1. Always unplug the unit's AC power cord from the AC

power source and disconnect the DC Power Jack before

attempting to:

4. Check the insulation between the blades of the AC plug

and accessible conductive parts (examples: metal panels,

input terminals and earphone jacks).

5. Insulation Checking Procedure: Disconnect the power

cord from the AC source and turn the power switch ON.

Connect an insulation resistance meter (500 V) to the

blades of the AC plug.

(a) remove or reinstall any component or assembly, (b)

disconnect PCB plugs or connectors, (c) connect a test

component in parallel with an electrolytic capacitor.

The insulation resistance between each blade of the AC

plug and accessible conductive parts (see above) should

be greater than 1 megohm.

2. Some components are raised above the printed circuit

board for safety. An insulation tube or tape is sometimes

used. The internal wiring is sometimes clamped to

prevent contact with thermally hot components. Reinstall

all such elements to their original position.

6. Always connect a test instrument’s ground lead to the

instrument chassis ground before connecting the positive

lead; always remove the instrument’s ground lead last.

3. After servicing, always check that the screws,

components and wiring have been correctly reinstalled.

Make sure that the area around the serviced part has not

been damaged.

1-3 Static Electricity Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called

Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect transistors. The

following techniques will reduce the incidence of component damage caused by static electricity.

1. Immediately before handling any semiconductor

components or assemblies, drain the electrostatic charge

from your body by touching a known earth ground.

Alternatively, wear a discharging wrist-strap device. To

avoid a shock hazard, be sure to remove the wrist strap

before applying power to the monitor.

6. Do not remove a replacement ESD from its protective

package until you are ready to install it. Most

replacement ESDs are packaged with leads that are

electrically shorted together by conductive foam,

aluminum foil or other conductive materials.

7. Immediately before removing the protective material

from the leads of a replacement ESD, touch the

protective material to the chassis or circuit assembly into

which the device will be installed.

2. After removing an ESD-equipped assembly, place it on a

conductive surface such as aluminum foil to prevent

accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can

generate electrical charges sufficient to damage ESDs.

Caution: Be sure no power is applied to the

chassis or circuit and observe all

other safety precautions.

4. Use only a grounded-tip soldering iron to solder or

desolder ESDs.

8. Minimize body motions when handling unpackaged

replacement ESDs. Motions such as brushing clothes

together, or lifting your foot from a carpeted floor can

generate enough static electricity to damage an ESD.

5. Use only an anti-static solder removal device. Some

solder removal devices not classified as “anti-static” can

generate electrical charges sufficient to damage ESDs.

1-2

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Precautions

1-4 Installation Precautions

1. For safety reasons, more than two people are

required for carrying the product.

6. Keep the antenna far away from any high-voltage

cables and install it firmly. Contact with the high-

voltage cable or the antenna falling over may

cause fire or electric shock.

2. Keep the power cord away from any heat emitting

devices, as a melted covering may cause fire or

electric shock.

7. When installing the product, leave enough space

(10cm) between the product and the wall for

ventilation purposes.

3. Do not place the product in areas with poor

ventilation such as a bookshelf or closet. The

increased internal temperature may cause fire.

A rise in temperature within the product may

cause fire.

4. Bend the external antenna cable when connecting

it to the product. This is a measure to protect it

from being exposed to moisture. Otherwise, it

may cause a fire or electric shock.

5. Make sure to turn the power off and unplug the

power cord from the outlet before repositioning

the product. Also check the antenna cable or the

external connectors if they are fully unplugged.

Damage to the cord may cause fire or electric

shock.

1-3

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Precautions

Memo

1-4

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Product Specifications

2-1 Fashion Feature

-. Improved Response Time by Adopting RTA: 6ms (Based on "Gray to Gray")

-. High contrast ratio & high aperture structure

-. High speed response

-. WQXGA (2560 x 1600 pixels) resolution

-. S-PVA (Super Patterned Vertical Alignment) mode

-. Direct BLU Structure (Cold Cathod Fluorescent Tube)

-. Sync & DE(Data Enable) mode

-. Dual Link TMDS serial interface (4pixel/clock)

-. RoHS compliance

-. Pb-free compliance

2-2 Spec Comparison

Key Specification

LHU30BS

305T PLUS

Model

Screen Size

Brightness

30"

300cd/m

Contrast

Fast Response Time

Magic color

1000 : 1

RTA chip

6ms (g to g)

16ms (w to b)

Magic Pivot

Magic Tune

Magic Zone

Detail control

Gamma,

Color temperature

Sharpness

Magic Bright

2-1

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Product Specifications

2-3 Specifications

Item

Description

LCD Panel

TFT-LCD panel, RGB vertical stripe, normally black transmissive,

30-Inch viewable, 0.2505 (H) x 0.2505 (V) mm pixel pitch

Scanning Frequency

Horizontal : 98.7kHz

Vertical : 60Hz

Display Colors

16.7 Million colors

Maximum Resolution

Horizontal : 2560 Pixels

Vertical : 1600 Pixels

Input Video Signal

Input Sync Signal

Type : Seperate H/V sync

Maximum Pixel Clock rate 268.5 MHz

Active Display

Horizontal/Vertical

641.28 mm / 400.8 mm

AC power voltage & Frequency

Power Consumption

AC 90 ~ 264 Volts, 60/50 Hz

130W (Max)

Dimensions

Set (W x D x H)

Weight (Set)

690.2 x 502 x 280 mm (27.2 x 19.8 x 11 inch)

12 kg

Environmental Considerations

-Designs and specifications are subject to change without prior notice.

2-2

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Product Specifications

2-4 Spec Comparison to the Old Models

LS17VDP(770P)

LS19VDP(970P)

Model

LHU30BS(305T PLUS)

Design

6ms (Gray to Gray)

The IC for the enhancement of the response time is applied.

8ms (Gray to Gray)

The IC for the enhancement of the response time is applied.

Repones Time

Magic pivot

Magic color

Magic zone

Magic tune

AUTO(Pivot program + Sensor IC)

Ver 3.6 Applied

Main PBA

SMPS PBA

2-3

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Product Specifications

2-5 Option Specification

Item

Item Name

CODE.NO

Remark

Quick Setup Guide

BN68-00847B

Warranty Card

(Not available in all locations)

BH75-00146B

BN59-00565A

User's manual,

Monitor Driver

Power Cord

DVI Cable

3903-000082

BN39-00754A

2-4

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

14-1 Technical Terms

-TFT-LCD

-Image Lock

(Thin film Transistor Liquid Crystal Display)

ADC(Analog to Digital Converter)

This is a circuit that converts from analog signal to

digital signals.

This means "Fineness adjustment " in LCD

Monitor, the features are "Fine" and "Coarse"

-FINE

"Fine" adjustment is used to adjust visibility by

control phase difference.

-PLL(Phase Locked Loop)

During progressing ADC, Device makes clock syn-

chronizing HSYNC with Video clock

-COARSE

This is a adjustment by tuning with Video colck

and PLL clock.

-Inverter

Device that supply Power to LCD panel lamp. this

device gernerate about 1,500~2,000V.

-DVI (Digital Visual Interface)

This provides a high speed digital connection for

visual data types that is display technology inde-

pendent. this interface is primarily forcused at pro-

viding a connection between a computer and

its display device.

AC Adapter

Device that converts AC(90V~240V) to DC(+12V

or 14V)

SMPS(Switching Mode Power Supply)

Switching Mode Power supply. This design tech-

nology is used to step up/down the input power by

switching on/off

-L.V.D.S.(Low Voltage Differential Signaling)

a kind of transmission method for Digital.It can be

used from Main PBA to Panel.

-FRC(Frame Rate Controller)

-T.M.D.S

Technology that change image frame quantity dis-

played on screen for one second.

(Transition minimized Differential Signaling)

a kind of transmission method for Digital.

It can be used from Video card to Main PBA.

Actually TFT-LCD panel require 60 pcs of frame

for one second.

so,this technology is needed to convert input

image to 60 pcs regardless input frame quantity.

-DDC(Display data channel)

It is a communication method between Host

Computer and related equipment.

It can make it Plug and Play between PC and

Monitor.

-Image Scaler

Technology that convert various input resolution to

other resolution.(ex. 640* 480 to 1024*768)

-EDID

-Auto Configuration(Auto adjustment)

This is an algorithm to adjust monitor to optimum

condition by pushing one key.

Extended Display Identification Data PC can rec-

ognize the monitor information as Product data,

Product name,Display mode,Serial number and

Signal source,etc through DDC Line communicat-

ing with PC and Monitor.

-OSD(On Screen Display)

On screen display. customer can control the

screen easily with this.

14-1

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

-Dot Pitch

The image on a monitor is composed of red, green

and blue dots. The closer the dots, the higher the

resolution. The distance between two dots of the

same color is called the 'Dot Pitch'. Unit: mm

-Vertical Frequency

The screen must be redrawn several times per

second in order to create and display an image for

the user. The frequency of this repetition per sec-

ond is called Vertical Frequency or Refresh Rate.

Unit: Hz

Example: If the same light repeats itself 60 times

per second, this is regarded as 60 Hz.

-Horizontal Frequency

The time to scan one line connecting the right

edge to the left edge of the screen horizontally is

called Horizontal Cycle. The inverse number of the

Horizontal Cycle is called Horizontal Frequency.

Unit: kHz

-Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the

top to the bottom in order is called the Non-

Interlace method while showing odd lines and then

even lines in turn is called the Interlace method.

The Non-Interlace method is used for the majority

of monitors to ensure a clear image. The Interlace

method is the same as that used in TVs.

-Plug & Play

This is a function that provides the best quality

screen for the user by allowing the computer and

the monitor to exchange information automatically.

This monitor follows the international standard

VESA DDC for the Plug & Play function.

-Resolution

The number of horizontal and vertical dots used to

compose the screen image is called 'resolution'.

This number shows the accuracy of the display.

High resolution is good for performing multiple

tasks as more image information can be shown on

the screen.

Example: If the resolution is 1280 x 1024 , this

means the screen is composed of 1280 horizontal

dots (horizontal resolution) and 1024 vertical lines

(vertical resolution).

14-2

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

14-2 Connecting Your Monitor

1. Connect the power cord for your monitor to the POWER port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

2. Using the DVI-D (Digital) connector on the video card.

Connect the DVI-D cable to the DVI-D port on the back of your monitor.

3. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

14-3

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

14-3 Pin Assignments

Sync

Type

24P DVI-D

Pin No.

Data Rx3+

+5V_M

+5V_M GND

Hot plug D

Rx0-

Rx2-

Rx2+

GND

Data Rx4-

Data Rx4+

DDC Clock (SCL)

DDC Data (SDA)

Rx0+

GND

Data Rx5-

Data Rx5+

GND

Rx1-

Rx1+

RxC+

RxC-

Data Rx3-

14-4

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

14-4 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard for computer-

generated video signals.

Table 2-1 Timing Chart

VESA-Reduced Blanking

Mode

1280/60Hz

1280X800

2560/60Hz

2560X1600

Timing

49.306

20.282

0.451

1.127

18.028

0.676

59.91

16.692

0.122

0.284

13.225

0.061

98.713

10.13

0.119

0.298

9.534

0.179

59.972

16.675

0.061

0.375

16.209

0.030

fH (kHz)

A μsec

B μsec

C μsec

D μsec

E μsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

Clock

Freq.

(MHz)

71.00

268.500

Polarity

H.Sync

Positive

Negative

V.Sync

Separate Sync

Video

H/V Composite Sync

Sync-on-Green

Video

Sync

A : Line time total

C : Back porch

E : Front porch

B : Horizontal sync width

D : Active time

O : Frame time total

P : Vertical sync width

R : Active time

Q : Back porch

S : Front porch

14-5

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally is called

Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an

image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz

14-6

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

14-5 Panel Description

Maker

VENDOR P/N

PANEL_CODE

PANEL_ABB STICKER_CODE

Remarks

SEC

for TV

SEC

LT140X1-002

BN07-00004A

BN07-00009A

BN07-00022A

BN07-00005A

BN07-00001A

BN07-00010A

BN07-00019A

BN07-10001D

BN07-10001E

BN07-00018A

BN07-00015A

BN07-00016A

BN07-00026A

BN07-00027A

BN07-00032A

BN07-00034A

BN07-00036A

BN07-00037A

BN07-00041A

BN07-00039A

BN07-00045A

BN07-00046A

BN07-00047A

BN07-00053A

BN68-00239H

LT150XS-L01

LT150XS-L01-B

LTM150XS-L02

LT181E2-132

LT150XS-T01

LTM181E3-132

LT170E2-131

LT181E2-131

LTM170E4-L01

LTM240W1-L01

LTM213U3-L01

LTM150XH-L01

LTM150XH-L03

LTM150XS-L01

LTM181E4-L01

LTM170EH-L01

LTM170E5-L01

LTM150XH-L11

LTM213U4-L01

LTM150XH-L01(ZPD)

LTM150XH-L04

LTM170W1-L01

LTM150XH-L06

DELL(ZPD)

PVA

ZPD

New panel with high brightness

Panel for TV

Panel for TV/ High luminance for 450cd _ SONY&EOS Team Panel

LTM153W1-L01

LTM170EH-L05

LTM170E5-L03

LTM190E1-L01

LTM181E5-L01

LTM150XP-L01

LTM240W1-L02

LTM170EU-L01

LTM170E5-L04

LTA220W1-L01

LTM170E6-L02

LTM170W1-L01

LTM170EH-L01

LTM170E5-L01

LTM170EH-L05

LTM170E5-L03

LTM170EU-L01

LTM170E5-L04

LTM170E6-L02

LTM150XH-L06

LTM153W1-L01

LTM170W1-L01

LTM170EH-L05

LTA400W1-L01

LTM153W1-L01

LTM150XH-L06

LTM170W1-L01

LTM170EH-L05

LTM220W1-L01

LTM150XH-L06

LTM153W1-L01

LTM170WP-L01

LTM213U4-L01

LTA260W1-L01

LTA220W1-L01

LTA320W1-L01

BN07-00054A

BN07-00055A

BN07-00056A

BN07-00057A

BN07-00061A

BN07-00065A

BN07-00062A

BN07-00071A

BN07-00072A

BN07-00074A

BN07-00075A

BN07-00082A

BN07-00080A

BN07-00081A

BN07-00083A

BN07-00084A

BN07-00085A

BN07-00086A

BN07-00087A

BN07-00091A

BN07-00092A

BN07-00100A

BN07-00097A

BN07-00109A

BN07-00110A

BN07-00111A

BN07-00112A

BN07-00113A

BN07-00114A

BN07-00117A

BN07-00118A

BN07-00119A

BN07-00039A

BN07-00121A

BN07-00074B

BN07-00108A

Use NIKE MODEL

Panel EOS proj. for high brightness of 17" EH-L05

Dell 1702FP pro. E4. EH mechanicalCompatible

DELL 1900 FP

18" narrow bezel GH18PS

AMLCD PVA PANEL

Panel for 15" Wide TV

Slim design, TN

E5-L04 6 bits FRC... for IBM

Panel for 22" TV

AMLCD Narrow & slim design 17" PVAmode

LTM170W1-L01 ZPD panel

LTM170EH-L01 ZPD panel

LTM170E5-L01 ZPD panel

LTM170EH-L05 ZPD panel

LTM170E5-L03 ZPD panel

LTM170EU-L01 ZPD panel

LTM170E5-L04 ZPD panel

LTM170E6-L02 ZPD panel

Color coordinates change for LCD TV

AMLCD WIDE 15",9/10

Color Coordinates change code management

LTM170E5-L05 Color Coordinates Change Panel Code

PANEL of AMLCD 40" TV

Color coordinates change 0.280/0.290, 10000k & ZPD Panel

ZPD Panel for AMLCD 22" TV

ZPD Panel code

PVA Panel for NIKE

21.3" NARROW

VENUS

Panel B-level panel code for 22" TV Panel

Panel for AMLCD 32" TV

14-7

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Maker

VENDOR P/N

PANEL_CODE

PANEL_ABB STICKER_CODE

Remarks

SEC

LTM213U4-L01

LTM170E6-L04

LTM190E1-L01

M150X4-L06

BN07-00124A

BN07-00129A

BN07-00088A

BN07-00137A

BN07-00139A

BN07-00128A

BN07-00143A

BN07-00144A

BN07-00129B

BN07-00108B

BN07-00151A

BN07-00134A

BN07-00128B

BN07-00145A

BN07-00158A

BN07-00159A

BN07-00151B

BN07-00157A

BN07-00160A

BN07-00134B

BN07-00145B

BN07-00134B

BN07-00164A

BN07-00164B

BN07-00160B

BN07-00172A

BN07-00124B

BN07-00189A

BN07-00189B

BN07-00188A

BN07-00188B

BN07-00191A

BN07-00191B

BN07-00184A

BN07-00185A

BN07-00186A

BN07-00195A

BN07-00197A

BN07-00197B

BN07-00202A

BN07-00187A

BN07-00195B

BN07-00206A

BN07-00200A

BN07-00214A

BN07-00218A

BN07-00222A

BN07-00190B

BN07-00223A

BN07-00196A

BN07-00229A

BN07-00239A

BN07-00245A

BN07-00231A

BN07-00231B

BN07-00244A

BN07-00245A

BN07-00227A

BN07-00249A

BN07-00250A

BN07-00219A

NARROW BEZEL 21 " PANEL

HIGHLAND 17" LOW PANEL (Panel only for TCO03)

LTM190E1-L01 ZPD panel

15" Narrow & Slim panel

LTA170V1

17" Panel for Muse 4:3 VGA TV

LTM190E1-L02

LTM170EX-L01

LTM170E8-L01

LTM170E6-L04

LTA320W1-L02

LTM190E1-L03

LTM240W1-L03

LTM190E1-L02

LTM190E4-L01

LTM170E8-L01

LTM170EX-L01

LTM190E1-L03

LTA460H1-L01

LTM170EU-L11

LTM240W1-L03

LTM190E4-L01

LTM240W1-L03

LTM150XO-L01

LTM170EU-L11

LTA320W2-L01

LTM213U4-L01

LTM170EU-L11

LTM240W1-L04

LTM190EX-L01

LTM190EX-L02

LTA230W1-L02

LTA260W2-L01

LTA400W2-L01

LTM240M1-L01

LTM150XO-L01

LTM170EU-L21

LTA460W2-L03

LTM240M1-L01

M170EX-L21

E10

E11

E12

E13

E14

E15

E16

E17

E18

E19

E20

E21

E22

E23

E24

E25

E26

E27

E28

E29

SPZ

STH

STZ

SPH

SPZ

STH

STZ

SPZ

SPH

STH

STZ

SPZ

STZ

SPZ

STZ

SPZ

STZ

SPZ

STZ

SPZ

SPH

SPZ

STZ

SPZ

New Panel from AMLCDl, Specification : 6bit Driver IC

Development new Panel from AMLCD

ZPD panel for AMLCD (Panel only for TCO03)

Creat B-level Panel code for AMLCD 32" TV

Development new 19" Panel form AMLCD (Panel only for TCO03)

AMLCD 24" panel development

New Panel from AMLCD, Specification : 6bit Driver IC(ZPD)

AMLCD 24" new panel development

ZPD code derivation

Creat new panel code for AMLCD 19" (Panel only for TCO03)

creat panel code for AMLCD 46" TV

creat new panel code for AMLCD 17" (Panel only for TCO03)

24" panel ZPD code derivation

AMLCD 19" ZPD Panel code derivation

24" panel ZPD code derivation

AMLCD 15" XO-L01 new panel development

AMLCD 15" XO-L01 ZPD code derivation

AMLCD 17" NEW panel code derivation

AMLCD 32" NEW panel

21.3" Narrow PANEL ZPD Panel derivation

AMLCD EU-L11 Pb free panel code derivtion

AMLCD EU-L11 Pb free panel ZPD code derivation

24" A-DCC NEW panel

24" A-DCC panel ZPD code derivation

AMLCD 19" TN NEW Panel

AMLCD 19" TN NEW Panel ZPD

AMLCD 23" 16:9 NEW Panel

AMLCD 26" 16:9 NEW Panel

AMLCD 40" 16:9 NEW Panel

24" high brightness panel

AMLCD 15" XO-L01 Pb free panel code

AMLCD 15" XO-L01 Pb free panel ZPD code

AMLCD EU-L21 ZPD NEW code derivation

BEETOVEN 46"ZPD NEW Panel

24" high brightness panel ZPD code derivation

AMLCD LTM170EX-L21 ZPD NEW code derivation

AMLCD 46" LED BLU panel

LTA460H3-L01

LTM170EU-L15

LTM170E8-L21

LTM190EX-L21

LTM201U1-L01

LTM190E4-L21

LTA570H1-L01

LTM150XO-L21

LTA260W2-L11

LTA400WS-LH1

LTM213U6-L01

LTA320WS-LH2

LTA400WS-LH1

LTM190M2-L01

LTM201UX-L01

LTM240M1-L02-A05

LTA320W3-L02

High brightness For AMLCD EU-L15 TV ZPD NEW code derivation

AMLCD LTM170E8-L21 PVA ZPD NEW code derivation

DISPLAY LCD

AMLCD 20.1" Normal panel ZPD code derivation

HAYDN 17" PZD code PANELderivation

AMLCD 57" NEW Panel

AMLCD 15" XO-L21 8ms panel code

AMLCD 26" 16:9 7Line NEW Panel

AMLCD 40" 16:9 SPVA 90% NEW Panel

AMLCD 21.3" PVA NEW Panel Code

AMLCD 21.3" PVA Panel HPD Code

AMLCD 32" 16:9 SPVA 90% NEW Panel

AMLCD 40" 16:9 SPVA 90% NEW Panel

AMLCD 19" TN Wide NEW Panel Code

AMLCD 20.1" TN NEW Panel Code

24" High brightness Slim panel ZPD code derivation

AMLCD 32" NEW FFL Panel

14-8

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Maker

VENDOR P/N

PANEL_CODE

PANEL_ABB STICKER_CODE

Remarks

SEC

LTA320W2-L11

LTA460WS-L02

LTA400WT-L01

LTM240M2-L02

LTM210M2-L02

LTA320WT-L11

LTM190EX-L21-G

LTA320WT-L14

LTM190M2-L01-D016

LTM190EX-L31

LTM190M2-L02

LTA400WS-L01

LTA460WS-L01

LTM190E4-L31

LTM170EX-L31

LTA460HS-LH1

LTA320WT-LF1

LTA460WT-L02

LTA400WH-LH1

LTM240M1-L02-D015

LTM300M1-P01

BN07-00259A

BN07-00252A

BN07-00264A

BN07-00267A

BN07-00230A

BN07-00257A

BN07-00274A

BN07-00247A

BN07-00280A

BN07-00279A

BN07-00287A

BN07-00246A

BN07-00311A

BN07-00316A

BN07-00278A

BN07-00291A

BN07-00323A

BN07-00284A

BN07-00271A

BN07-00331A

BN07-00326A

SPZ

STZ

SPZ

STZ

SPZ

STZ

SPZ

IP Board for AMLCD 32" 16:9 NEW Panel

AMLCD 46" 16:9 SPVA 72% NEW Panel

All LCD Monitor 24" wide SPVA ZPD NEW code derivation

AMLCD 19" TN Glare NEW Panel Code

AMLCD 19" TN Wide change Gamma Panel Code

AMLCD 19" TN NEW Panel Code

AMLCD 19" TN Wide High brightness NEW Panel Code

Display-LCD (Div) 07AH

AMLCD LTM170EX-L31 ZPD

AMLCD 46" 16:9 FHD / 60Hz / 8bit / SPVA 92%

AMLCD 46" 16:9 HD / 60Hz / 8bit / SPVA 72% /

AMLCD 40" 16:9 SPVA 92% 10bit 120Hz

CPT

CLAA150XG09

CLAA170EA02

CLAA150XG09

CLAA150XP01

CLAA170EA07

CLAA170EA07Q

CLAA150XP01F

CLAA201WA03Q

CLAA320WA01

CLAA170ES01

CLAA070VA02

BN07-00141A

BN07-00148A

BN07-00148B

BN07-00141B

BN07-00173A

BN07-00173B

BN07-00174A

BN07-00174B

BN07-00220A

BN07-00220B

BN07-00236A

BN07-00269A

BN07-00276A

BN07-00261A

BN07-00265A

CPT 15" Monitor new panel development

17" CPT NEW development panel

17" CPT ZPD panel code derivation

PTZ

PTH

PTZ

PTH

PTZ

PTH

PTZ

PMZ

PTZ

CPT 15" panel ZPD code derivation (GOYA-PJT)

CPT 15" PSWG code derivation

CPT 15" PSWG panel ZPD code derivation

CPT 17" PSWG code derivation

CPT 17" PSWG type New Panel code

CPT 17" PSWG R/T 8msec code derivation

CPT 17" PSWG R/T 8msec HPD code derivation

CPT 15" PSWG panel ZPD & Lead free code derivation

CPT 20.1" wide TN ZPD New code derivation

CPT 32" 16:9 MVA 8bit 60Hz / Panel brown

CPT 17" Slim TN ZPD Type New code derivation

CPT Panel code derivation for Digital Album

TOSHIBA

LTM15C419(A)

LTM15C423(B)

LTM18C161

LTM15C443

LTM15C458

LTM15C458S

LTM15C458

LTM15C458S

BN07-00002A

BN07-00006A

BN07-00008A

BN07-00031A

BN07-00043A

BN07-00077A

BN07-00078A

BN07-00099A

TSB 15" high brightness Panel

Toshiba ZPD panel

TSB LTM15C458S ( ZPD )

HANNSTAR

HSD150MX41A(A)

HSD150MX12

BN07-00020A

BN07-00030A

BN07-00180A

BN07-00180B

BN07-00210A

BN07-00226A

BN07-00256A

BN07-00270A

BN07-00317A

TTL type

HSD170ME13

NTH

NTZ

Hannstar 17" TN new panel development

Hannstar 17" TN new panel development ZPD code derivation

Hannstar 19" TN new panel development

Hannstar 15" slim panel ZPD code derivation

Hannstar 19" TN PSWG 8ms new panel development

Hannstar 19" TN Slim 5ms new panel development

HSD170ME13

HSD190ME12

HSD150MX17-A

HSD190ME12-A10

HSD190ME13-D11

HSD190ME13-A13

TORISAN

TM150XG-22L03(A)

TM150XG-26L06

TM181SX-76N01

TM150XG-26L06

BN07-00021A

BN07-00042A

BN07-00048A

BN07-00059A

15" XGA TN MODE(ZPD)

14-9

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Maker

VENDOR P/N

PANEL_CODE

PANEL_ABB STICKER_CODE

Remarks

TORISAN

TM290WX-71N31

TM396WX-71N31

TM150XG-26L09

TM150XG-26L10

TM190SX-70N01

TM181SX-76N01

TM190SX-70N01

TM290WX-71N31

TM396WX-71N31

TM22OWX-71N31

TM396WX-71N32A

TM190SX-70N02

TM150XG-A01

BN07-00063A

BN07-00064A

BN07-00073A

BN07-00089A

BN07-00090A

BN07-00098A

BN07-00106A

BN07-00107A

BN07-00115A

BN07-00116A

BN07-00125A

BN07-00127A

BN07-00150A

BN07-00154A

BN07-00154B

BN07-00162A

BN07-00162B

RS24NS (TORISAN 29" NEW PANEL)

RS24NS (TORISAN 40" NEW PANEL)

Panel for 15" TV

L10(change except D/IC) ZPD

L10 NORMAL

Torisan 19" Panel

ZPD Panel code

Color Coordinates change panel for TORISAN 29" TV

Color Coordinates change panel for TORISAN 40" TV

Development TORISAN 22" TV PANEL (ZPD)

Development TORISAN 22" TV PANEL (HPD)

120V inverter Exclusive panel

RP,Q

RMH

RMZ

RTH

RTZ

Torisan 6bit panel code Derivation

Torisan 15" Narrow & Slim panel development

Torisan 15" N&S panel ZPD code derivation

TM150XG-A01

SHARP

LQ181E1DG11(A)

LQ150X1LW71

LQ370T3LZ41

BN07-10001C

BN07-00067A

BN07-00216A

SHARP 15" PVA PANEL

Rome2

FAZ

HITACHI

TX38D12VC0CAA(A)

TX43DVCOCAB

BN07-00003A

BN07-00060A

BN07-00101A

BN07-00122A

BN07-00123A

BN07-00169A

BN07-00123B

HIZ

17" SXGA PVA MODE

ZPD Panel

TX43D15VC0CAB

TX51D11VC0CAB

TX54D11VC0CAB

TX80D12VC0CAB

TX54D11VC0CAB

20.1" NARROW

21.3" NARROW

Development new panel for Hitachi 32" TV (ZPD)

Hitachi 21.3"ZPD panel

IBM

ITSX94S

BN07-00017A

BN07-00028A

UNIPAC

UM170E0

Loaded by cisdba

HYUNDAI

Derivation

HT15X13

BN07-00035A

BN07-00049A

BN07-00093A

BN07-00094A

BN07-00095A

BN07-00096A

BN07-00105A

BN07-00146A

BN07-00146B

BN07-00167A

BN07-00167B

BN07-00240A

BN07-00263A

BN07-00266A

HT17E11-200

HT17E11-300

HT17E11-400

HT17E12

TN MODE

HT17E11-300 ZPD panel

HT17E11-400 normal panel

HT17E11-400 ZPD panel code

HT17E12 ( Narow & slim Design )

ZPD Panel code

HT17E12

HT15X15-D00

HT15X15-D01

HT17E13-100

HT170EX1-100

HT201V01-100

HT170EX1-101

Development for Ares 15" Hydis TV

Derivation panel HPD for Ares 15" Hydis TV

PINEHURST-2(IBM) PJT 17" HYDIS PANEL Derivation

PINEHURST-2(IBM) Hydis 17" ZPD code Derivation

17" EX compatible Hydis Slim panel development

Hydis 20.1" 4:3 VGA Mode TN NEW Panel

17" EX compatible Hydis Slim panel multi channel IC NEW

DTH

DTZ

ACER

L170E3

BN07-00044A

BN07-00076A

BN07-00102A

BN07-00170A

BN07-00170B

BN07-00171A

BN07-00163A

BN07-00177A

BN07-00171B

BN07-00194A

BN07-00192A

TN(ADT)

M170EN05

M190EN02

M170EN06

T260XW01

A201SN01

M170EN06

T315XW01

M170EG01

AU 17" Panel ( Narrow & slim design )

ZPD Panel code

AMH

AMZ

ATH

AMZ

ATZ

AMZ

ATH

AU Monitor 19" new panel development (P19-1S)

AU 19" ZPD code derivation (ZPD)

AU Monitor 17" New panel development

AU 26" new panel development (NF26EO)

AU TV panel 20.1" TN SVGA new panel development

AU Monitor 17" ZPD code Derivation

New AU 32"

AU TN PSWG type New Panel code

14-10

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Maker

VENDOR P/N

PANEL_CODE

PANEL_ABB STICKER_CODE

Remarks

ACER

M170EG01

M190EN04

T260XW02

M170EG01 V8

T260XW02

T315XW01

M190EN03

T315XW01

BN07-00192B

BN07-00203A

BN07-00208A

BN07-00221A

BN07-00233A

BN07-00234A

BN07-00224A

BN07-00237A

ATZ

ATH

AMZ

ATZ

AMZ

AU TN PSWG type New Panel ZPD Derivation code

AU Monitor 19" ZPD New code Derivation

AUO 26"

AU TN PSWG type New Panel (8msec) ZPD Derivation code

AUO 26" New Panel (Cosmetic spec down grade)

AUO 32" New Grade (Cosmetic spec down grade)]

AU Monitor 19" MVA New code Derivation

New LCD TV VE project : delete DBEF sheet * Panel, model division

ACER

grade * Panel

ACER

T315XW01

ACER

T315XW01

BN07-00238A

AMZ

New LCD TV VE project : delete DBEF sheet + 'A-'

M201UN02 V3

M190EN04 V7

A070VW01

BN07-00168A

BN07-00168B

BN07-00248A

BN07-00235A

BN07-00253A

AMZ

AMH

ATZ

AMZ

AU Monitor 19" TN Glare ZPD New code Derivation

New Panel code Derivation for Digital Album

LCD TV VE item model * Panel, Model division add version:

T315XW01

T260XW02

BN07-00254A

BN07-00260A

BN07-00255A

BN07-00324A

BN07-00314A

AMZ

ATZ

AMZ

ATZ

AUO 26" VE item apply model

AUO 17" Slim TN ZPD Type New code Derivation

for ROME 37" model development

M170EU01

T370XW01

T315XW02(V3),

A201SN02 V5

CHIMEI

M170E3-LO1

M150X3-L01

M170E4-L01

M150X2-L01

M150X3-L01

M170E3-L01

M170E4-L01

V296W1-L01

M170E6-L02

M190E2-L01

M150X4-L06

M170E6-L01

V201V1-T01

M170E6-L02

M170E6-L05

M150X4-L06

M170E5-L05

V230W1-L02

V320B1-L01

V270W1-L01

M190E5-L0A

M190E3-L0A

M170E7-L01

M190A1-L01

V201V1-T03

M201P1-L01

M220Z1-L01

M190E5-L0G

BN07-00050A

BN07-00051A

BN07-00052A

BN07-00066A

BN07-00079A

BN07-00103A

BN07-00104A

BN07-00120A

BN07-00126A

BN07-00131A

BN07-00137A

BN07-00133A

BN07-00133B

BN07-00135A

BN07-00126B

BN07-00152A

BN07-00152B

BN07-00137B

BN07-00165A

BN07-00165B

BN07-00209A

BN07-00207A

BN07-00136A

BN07-00213A

BN07-00212A

BN07-00232A

BN07-00228A

BN07-00275A

BN07-00268A

BN07-00321A

BN07-00337A

TN PANEL

COMPATIBLE

MVA PANEL

CHIME 15"I PVA PANEL

Chimei ZPD panel

ZPD Panel code

MVA

HIGHLAND 17" LOW PANEL

GH19AS,BS CHIMEI PANEL

15" Narrow & Slim panel

2003-03-11 vendor change

ZPD derivation panel

CHIMEI 20.1" panel development

HIGHLAND 17" LOW PANEL ZPD derivation panel

CMO 17" new panel development code

CMO 17" ZPD panel code derivation

Chimei 15" Narrow & Slim panel ZPD derivation

CMO 17" new panel development code (GOYA2-PJT)

CMO 17" ZPD panel(GOYA2-PJT)

CMO 23" new development

CMO 32" new development

CHI MEI 27" panel development

CTH

CTZ

CMZ

CTZ

CMZ

CTZ

CMO M190E3-L0A MVA Type New code derivation

CMO 17" Slim TN ZPD Type New code derivation

CMO 19" Wide TN ZPD Type New code derivation

CMO 20.1" (V201V1-T01) VE model

CMO 20.1" TN ZPD derivation

NEC

SVA150XG04TB

SVA170SX01TB

BN07-00225A

BN07-00272A

BTZ

SVA NEC 15" panel ZPD code

SVA NEC 17" panel ZPD code Brown

14-11

Download from Www.Somanuals.com. All Manuals Search And Download.

14 Reference Infomation

Memo

14-12

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

Notes

1. Before troubleshooting, setup the PC’ s display as below.

• Resolution: 2560 x 1600

• H-frequency: 98.7 kHz

• V-frequency: 60 Hz

2. If no picture appears, make sure the power cord is correctly connected.

3. Check the following circuits.

• No raster appears: Function PBA, Main PBA, Inverter, Panel

• 5V develop but no screen: Main PBA

• +24V, +18V does not develop: SMPS, Main PBA

4-1 No Power (SMPS)

Plug in the Power Cable

Check related circuit with IC801S

Vcc and Drain-Source Waveform

Stand by LED On?

Yes

(DSW)

Check the Vcc Circuit from DS803

Aroind 20V at 2pin on

Yes

Change ICM801S and check the

related circuit

Check DSW at ICM801S

Yes

Check the related circuit whit ICP 801S

and QP801S

Around 380V on CP803

Check 24V output related circuit with

zener diode (DZM854)

Yes

Check IC 8008 DC/DC convertor for

5.4V output

Replace LCD Panel.

Check ICM853(379Roo) for 18V output

4-1

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

WAVEFORMS

4-2

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

4-2 No Power (Main)

Check Function ass'y.

Does proper DC 6V

appear at Pin 1 of

CN601?

Check the FP801S at SMPS board

and related circuit

Yes

When Pin 1 of IC601 is DC 6V

does proper DC 3.3V appear at

Pin 3 of IC601?

Check IC601 and related circuit.

Yes

Check X200, IC200 and related

circuit.

X-200 oscillate Properly?

(Where pin 9 of IC200)

Yes

Dose proper DC3.3V appear at

pin 34 of IC200

Check IC200 and related circuit.

Check IC401 and related circuit

Yes

Dose proper +18V_Panel at pin

9-12 of CN401

Yes

Dose proper +24V_IN at

pin 14-16 of CN600

Check +24 output of the SMPS and

related circuit

Yes

Check LCD Panel and replace LCD

Panel

4-3

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

4-3 No Video (DIGITAL)

Check signal cable connection and

power.

Replace or check related circuit.

X200 oscillate properly?

Yes

Is there input data at

Check input part.

R122, R124, R127, R128,

R129 and R130?

Yes

3 4

Is there wave from

Does the output signal appear

at Pin 2, 3 of CN401?

Check LCD Panel and related circuit.

Yes

Check the LCD_ON at pin 33 of

IC200

Is there wave form

at pin 13 of CN401?

Yes

Replace LCD Panel.

4-4

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

WAVEFORMS

4-5

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Troubleshooting

Memo

4-6

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Wiring Diagram

8-1 Wiring Diagram (Main PCB)

8-1

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Wiring Diagram

8-2 Wiring Diagram (SMPS PCB)

8-2

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9 Schematic Diagrams

- This Document can not be used without Samsung s authorization.

9-1 Schematic Diagrams

9-1

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9-2 Connection Diagrams

9-2

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9-3 Micom Diagrams

9-3

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9-4 Power inverter Schematic Diagrams

9-4

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

WAVEFORMS

9-5

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9-5 SMPS Schematic Diagrams

9-6

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

9-6 SMPS Schematic Diagrams

9-7

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Schematic Diagrams

WAVEFORMS

9-8

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Cooktop 61 2431 User Guide
Radio Shack Speaker 40 4092 User Guide
Regency Stove C33 LP2 User Guide
RocketFish Headphones RF IC3BL User Guide
Samsung Blu ray Player BD C7900 User Guide
Samsung Digital Camera EC DV150FBPBUS User Guide
Samsung Laptop Q71 User Guide
Samsung Portable DVD Player DVD L75 L70 User Guide
Samsung Speaker System HW F850 User Guide
Sanyo DVR DSR 2016 User Guide