Sabrent USB‐DSC5 USB 2.0 to SATA/IDE Hard Drive Adapter
2.5” Notebook IDE Hard Drive
1. Connect the short 2.5” IDE connector from the Sabrent adapter to the pins on your 2.5” Hard Drive. Note the
keyed pin and slot and make sure that the drive and the device line up properly and are securely connected:
Figure A:
Figure B:
Figure C:
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connect the USB cable from the USB‐DSC5 to an available USB port on your computer.
Figure A:
3. In most cases, the USB cable will supply sufficient power for the drive to spin up and initiate. Some larger
capacity Hard Drives may require more power than USB to provide sufficient power to initiate. You may need to
use the supplied power supply to provide the extra needed power:
Figure A:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure B:
Figure C:
Figure D:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure E:
Figure F:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure G:
3.5” Desktop IDE Hard Drive
1. Most 3.5” IDE Hard Drives have Jumpers. Make sure they are set to Master Only. (Note: Please refer to the
drive manufacturer’s website for more information regarding your specific hard drive model.):
Figure A:
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connect the IDE power adapter directly in the IDE drive:
Figure A:
Figure B:
Figure C:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure D:
3. Connect the long 3.5 inch IDE connector to the pins on your hard drive. Note the keyed pin and slot and make
sure that the drive and the device line up properly and are securely connected:
Figure A:
Figure B:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure C:
4. Connect the USB cable from the DSC5 to a USB port on your computer.
Figure A:
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5/3.5 Inch SATA Drive
1. Connect the Sabrent converter to the power adapter, and then plug the SATA power end into the SATA drive
directly:
Figure A:
Figure B:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure C:
Figure D:
Figure E:
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Connect the SATA data cable into the Sabrent Converter, and then connect the other end directly into the SATA
drive:
Figure A:
Figure B:
Figure C:
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure D:
Figure E:
Figure F:
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connect the USB cable from the Sabrent converter to an available USB port on your computer.
Figure A:
Download from Www.Somanuals.com. All Manuals Search And Download.
Hard Drive Setup
For Windows 2000/XP/VISTA/7, no drivers or software are necessarry.
If the Hard‐Drive is brand new you may need to initialize it first in order to cause the Drive Letter to appear:
1. Click the Start button, right‐click on “My Computer”, and select “Manage”:
2. Click on “Disk Management”:
3. Locate the drive in the right column and right‐click on the drive and click “New Simple Volume”:
Download from Www.Somanuals.com. All Manuals Search And Download.
4. At the following prompt, click “Next”:
5. Click “Next”:
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Assign a drive letter to the drive, then click “Next”:
7. Click on “Format this volume with the following settings:” Change the “File system” to “NTFS”. Change the
“Volume label” to what you want the drive to be named. Click the checkbox for “Perform a quick format”.
Click “Next”:
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Click “Finish”. Windows will now begin formatting and initializing the disk:
9. Open “My Computer” and verify that the drive shows up properly:
Download from Www.Somanuals.com. All Manuals Search And Download.
If the drive has already been formatted, you can skip these steps.
1. Check the “Device Manager” to make sure that the “USB Mass Storage Device” driver appears under the
“Universal Serial Bus Controllers” section. Also check that the drive shows up under “Disk drives” as a “(Hard
drive model number) USB Device”. There should be no error message in your Device Manager, such as a bold ?
or ! :
2. You may also need to change the HDD settings from Dynamic to Basic, then format NTFS, and give it a drive
letter, but you should back up the data on your drive before doing this. To convert the disk from Dynamic to
Basic follow the instructions at the link included. http://sabrent.com/support/knowledgebase.php?article=58
3. Please Note: Make sure to disable disk drive password protection
Frequently Asked Questions:
1. My drive died or was damaged in my previous computer. Will it work with this adapter?
This adapter is the equivalent of plugging in the drive directly into your computer’s IDE or SATA port. If the drive
was damaged to the point where it doesn’t work when plugged directly into the computer, then it is likely that it
will not work using this adapter.
2. I set my IDE drive’s Jumper to the Master setting, but it still doesn’t show up on my computer.
Usually you will have to set the Jumper to Master, but depending on the specific drive and the specific settings
of the computer, you may have to set it to Slave or Cable Select.
3. My drive doesn’t show up on my computer, but it has data and works elsewhere.
Make sure you are connecting the Hard Drive in the correct sequence: First connect the power supply, and then
connect the USB Cable to the computer.
4. Why doesn’t my 3 TB hard drive show up as full capacity?
If the drive has is set to MBR (Master Boot Record) partition, then it will only allow a maximum usable amount
of 2TB. This limitation cannot be overcome in Windows 2000/XP. In Windows Vista & 7 there is support for
larger Hard Drives when you use the GPT partition type:
To convert the disk to a GPT partition disk in Windows Vista and Windows 7:
Go to “Disk Management” (See steps 1‐3), locate the disk in the list, right click the disk and click on “Convert to
GPT Disk”. You should now have access to the full capacity of your >2 TB disk partition.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|