SCdefault
900
Installation instructions
·
MONTERINGSANVISNING INSTALLATION INSTRUCTIONS
·
MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 M03-
Engine/cabin heater
Accessories Part No.
Group
Date
Instruction Part No.
Replaces
12 787 161
9:87-42
Jun 02
12 788 928
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 3
1
2
F920A012
Fuel line kit
1 Fuel line (pump-heater)
2 Fuel line (tank to pump)
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
4 12788928
F920A013
Electrical connection kit
Wiring harness
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 5
Important
WARNING
Work on the heater involves dismantling the vehi-
cle fuel system and emptying the fuel tank. When
carrying out the work the following points should
therefore be observed:
S Provide good ventilation! Use approved extrac-
tors for removing fuel fumes if they are availa-
ble.
S Use protective gloves! Prolonged contact with
fuel can cause skin irritation.
S Keep a class BE fire extinguisher close at
hand. Observe the risk of sparks, e.g. in con-
nection with breaking electrical circuits, short
circuiting, etc.
S Smoking is absolutely forbidden.
S Use protective goggles.
Important
The flexible bellows on the forward section of the
exhaust system must not be bent more than 5°
from its neutral alignment. This means that if the
forward section is hanging free, the bellows must
not be bent further than the amount already
caused by the weight of the system.
Excessive loading of the pipe can lead to residual
deformations in the components which can cause
noise, leakage and eventually failure.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
6 12788928
Preparations
Reduction of fuel pressure
1 Let the engine idle.
2 Remove fuse No. 2 (fuel pump) from the electri-
cal centre located in front of the battery in the
engine compartment.
3 When the engine has stopped the ignition key
must be turned to the OFF position.
4 Refit the fuse.
Emptying the fuel tank
Important
Pay attention to cleanliness when working on the
fuel system. Prevent dirt from entering the tank
and fuel lines.
Be careful not to damage the non-return valve in
the fuel tank when inserting and removing the suc-
tion pipe of the emptying unit.
The fuel tank is not fitted with a drain plug. Where
work on the fuel system requires emptying of the
fuel tank this is done with an emptying unit via the
filler pipe.
Before emptying read carefully through the instruc-
tions supplied with the emptying unit.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 7
6
5
5
4
5
5
F920A014
1 Disconnect the negative battery cable.
2 Remove the cap from the expansion tank.
3 Raise the car.
4 Remove the bolts from the forward section of
the exhaust system.
5 Remove the exhaust system.
6 Place a receptacle under the engine, open the
drain plug on the bottom of the coolant pump
and drain the coolant.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
8 12788928
9
7
8
14
8
15
37mm
94mm
10
11
F920A015
7 Unplug the connector at the front of the fuel tank
and detach the wiring harness from its mounting.
16 Remove the hose which is connected to the fuel
filler pipe ( the hose clip must be split with a saw)
and fit the hose from the set.
8 Place a pillar jack under the fuel tank and undo
the tank mounting straps.
Tightening torque 4 Nm (3 lbf ft)
9 Separate the fuel lines using tool 83 95 261 and
plug the fuel line tank connections in order to
prevent fuel spill.
17 Place the fuel tank on a pillar jack, lift the tank
slightly and connect the fuel filler vent hose. Lift
the fuel tank completely and connect the
remaining fuel lines.
10 Remove the filler pipe hose from the fuel tank.
18 Fit the fuel tank mounting straps.
11 Carefully lower the fuel tank until the joint in the
carbon filter vent hose becomes accessible.
Separate the joint in the carbon filter vent hose
and the joint in the fuel filler vent hose.
Tightening torque 24 Nm (18 lbf ft)
19 Plug in the connector at the front of the fuel tank
and fit the wiring harness into its mounting.
12 Lower the fuel tank completely and lift away to a
work bench.
20 Fit the drain plug in the bottom of the coolant
pump.
13 Mark the position of the hole where the heater
fuel pipe is to be inserted.
21 Lower the vehicle until it is just over the floor.
14 Drill a 10.5 mm hole in the tank.
Important
Be careful to prevent drill swarf from falling into the
tank.
15 Push the fuel pipe into the tank until the seal
locates against the tank and fasten the pipe to
the other fuel lines with a cable tie on each side
of the fuel line holder.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 9
26
26
22
23 23
24
25
26
23
22
22
F920A016
22 Unplug the connector from the air mass sensor,
separate the intake hose and remove the air fil-
ter cover. Remove the hose from the air filter
cover (if such a hose is fitted).
26 Fit the heater mounting bracket to the bulkhead.
Tightening torque 24 Nm (18 lbf ft)
Using benzine, clean an area between the sus-
pension strut mounting bolts on the top of the
right-hand suspension turret nearest to the
engine. Remove the extra label from the heater
and affix it to the cleaned area.
23 Remove from the turbo intake pipe the small
hose to the control valve (APC valve) and the
hose to the carbon filter vent-valve. Remove the
intake pipe.
24 Remove the heat shield from the turbo compres-
sor (two screws and a catch).
Important
Under no circumstances may this label conceal
any part of another label or plate.
25 Remove the coolant hoses from the connections
to the heat exchanger and remove from the ther-
mostat housing the hose which is nearest to the
expansion tank.
Important
Retain the hose clip, it is required for re-assembly.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
10 12788928
37
35
27
28
32
31
34
36
29
29
F920A017
27 Fit the hose clips (including the old clip) onto the
new coolant hoses. Connect the hose/pipe
assembly between the thermostat housing con-
nection and the heat exchanger connection
nearest to the expansion tank. Do not screw the
assembly to the bulkhead.
31 Protect the suspension turret and from above
manoeuvre the heater into place on its mount-
ing.
Note
The connector mounting can be bent slightly to
facilitate assembly.
Important
The heat shield on the hose should be slid towards
the thermostat housing so that the hose clip fits
into the cut-out in the heat shield.
Tightening torque 9 Nm (6.5 lbf ft)
Bend the connector mounting back into its orig-
inal shape.
32 Fit the connector into its mounting and reposi-
tion the cable tie around the connector.
28 Connect the other coolant hose to the heat
exchanger connection.
33 Connect the lower coolant hose to the heater
and tighten the hose clip.
29 Remove the control valve (APC valve) and
remove the crankcase ventilation hose from the
turbo compressor.
34 Connect the upper coolant hose to the heater
and tighten the hose clip.
30 Remove the plugs from the heater inlet and out-
let ports. Push aside the cable tie holding the
heater connector and detach the connector from
its mounting on the heater.
35 Attach the coolant pipe mounting to the brake
pipe cover plate on the bulkhead.
36 Connect the crankcase ventilation hose to the
turbo compressor and fit the control valve (APC
valve)
37 Connect the inlet hose of the heater to the fixing
in the hole in the longitudinal frame member.
Important
Check that the drainage hose is free from the
intake hose. If the wiring harness channel on the
heater is severely bent the drainage can be affect-
ed.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 11
38
38
38
38
38
38
38
38
38
38
38
38
F920A018
38 Remove the wiper arms using puller 85 80 144.
Remove also the bonnet seal and the cover over
the bulkhead space.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12 12788928
43
43
43
43
40
43
42
42
41
F920A019
39 Locate the "Pre Acc" outlet between the engine
bay main fuse box and the front wing and
remove any adhesive tape or dummy connector.
43 Fasten the wiring harness with cable ties (x7).
Position the "Pre-Acc" outlet between the wiring
harness and the front wing.
40 Plug the wiring harness from the installation set
into the connector on the heater and route it
through the bulkhead space to the "Pre Acc"
outlet adjacent to the engine compartment elec-
trical centre.
Important
Check that the drainage hose at the filter is cor-
rectly fitted.
44 Thread the fuel pump wiring harness down
alongside the fuel lines against the back edge of
the frame member.
Important
The wiring harness must be located in the seals by
the front wings.
41 Connect the ground cable to the front grounding
point (G30A) in the engine bay main fuse box.
42 Connect the wiring harness to the four pole "Pre
Acc" outlet.
Note
If the four pole "Pre Acc" outlet is already used,
connect into the existing connector as follows
– Unplug "Pre Acc"
– remove the seal from the connector on the
heater wiring harness and detach the cables
from the connector block
– fit the cables into the connector which was
plugged into "Pre-Acc", red cable (RD) in posi-
tion 1 and green cable (GN) in position 2
– Plug in the connector to "Pre Acc".
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 13
49
50
F920A020
45 Raise the car.
46 Pull down the fuel pump wiring harness.
47 Thread the fuel pump fuel line up between the
heater and the longitudinal frame member.
48 Connect the fuel line to the heater.
49 Fit the fuel pump fuel line into the clips on the
underside of the vehicle floor. The fuel line
should be located in the upper groove of each
clip.
50 Open the clips on the underside of the floor and
locate the fuel line in the grooves. Close the
clips and fasten the fuel line with cable ties (x7)
between the clips.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
14 12788928
51
53
57
54
56
54
55
F920A021
51 Position the fuel pump bracket up against the
vehicle floor, on the right-hand side in front of
the fuel tank, and drill holes using a 3.5 mm drill.
52 Deburr the holes and remove loose swarf and
paint particles. Clean with Teroson Cleaner FL
and apply Standox 1K primer. Apply a finishing
coat.
53 Fit the fuel pump with vibration damper and pro-
tective cover onto the bracket.
Important
The smaller diameter connection should point
towards the centre of the car and slightly forwards.
The protective cover should be positioned under
the pump.
54 Connect the fuel lines to the fuel pump using a
joint hose and two hose clips for each connec-
tion. The joint hose which has a smaller diame-
ter at one end should be arranged so that this
end fits onto the smaller diameter connection of
the pump. Attach the long fuel line to the pump
bracket by threading a cable tie through the hole
in the bracket.
55 Connect the wiring harness to the fuel pump.
56 Attach the harness to the bracket using a cable
tie.
57 Screw the bracket with the pump assembly onto
the floor of the vehicle.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
12788928 15
58
58
58
59
59
59
59
59
F920A022
58 Manoeuvre the heater exhaust pipe up towards
the heater and fit the end of the pipe onto the
exhaust port of the heater. Fasten the exhaust
pipe to the floor of the vehicle with the two nuts.
Tightening torque 5 Nm (3.5 lbf ft)
59 Fit the vehicle exhaust system.
Tightening torque 22 Nm (16.5 lbf ft)
60 Lower the vehicle until it is just over the floor.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
16 12788928
62 62
61
64
62
63
69
63
F920A023
61 Fit the heat shield to the turbo compressor (two
screws and a catch).
68 Start the heater by pushing the "CUSTOMIZE"
button on the SIDC, select "Parking heater",
push "SET", select "Manual control", push
“SET”, select “Heater on”, push “SET” and
check that the heater starts ( it has a delay of
about 1 minute). If necessary top up the cooling
system (engine switched off).
62 Fit the turbo intake pipe and then connect to the
pipe the small hose from the control valve (APC
valve) and the hose from the carbon filter vent
valve.
63 Fit the air filter cover and plug the connector into
the air mass sensor. Attach the hose to the air fil-
ter cover (if such a hose is fitted).
69 Fit the cover over the bulkhead space, fit the
bonnet seal and the wiper arms.
70 Adjust the clock/date.
64 Fill with coolant and check the system for leaks.
Fit the expansion tank cap.
71 Programme the heater Turn the ignition switch
to the ON position, push the "CUSTOMIZE" but-
ton on the SIDC, select "Parking heater", push
"SET", select "Manual control" and check that
the heater starts or select "Timer setting", "Tim-
er”, select a timer; “A”, “B” or “C”, programme in
a suitable time and push “SET”. Check that the
heater starts at the programmed time.
65 Connect the negative battery cable.
66 Connect the diagnostic tool, select car and mod-
el year, select “All”, select “Add/Remove”, select
the accessory and then “Add”.
67 Bleed the cooling system in the following way:
Note
Select “Manual control", press “SET”, select
“Heater off”, press “SET” and check that the
heater stops. Select “Back”, press “SET”, select
“Finish” and press “SET”.
The A/C or ACC should be turned OFF.
Fill the coolant system to the MAX level. Close
the expansion tank cap. Start the engine and run
at varying engine speeds until the radiator fan
cuts in. Carefully open the expansion tank cap
and top up to the MAX level. Close the cap.
Switch off the engine and if necessary top the
coolant up to the MAX level.
Saab 9-3 M03-
Download from Www.Somanuals.com. All Manuals Search And Download.
|