Elite 3XVandal Dome Cameras
For Flush or Surface Mount
Installation Manual
EV-2866-NKGQ NTSC
EV-2866-PKGQ PAL
3 Cameras in 1:
1/3” Sony Super HAD II CCD
600 TV Lines
12VDC/24VAC
2.8~12mm Varifocal lens
256x Digital slow shutter
On-screen display (OSD)
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Download from Www.Somanuals.com. All Manuals Search And Download.
Elite 3X Vandal Dome Cameras
Overview:
OSD joystick
Service
monitor port
BNC
connector
Camera
Set screw
Base
(For surface mounting only)
Dome
Rubber ring
Important:
Do not cut the DC jack or the female BNC
DC Plug to
terminal block
DC Jack
connector as this will void the warranty.
Before Starting:
1. Please read this manual carefully and keep it for future
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
reference.
2. Use the camera within given temperature and electrical
limits.
6. Do not open or disassemble the camera. There are no
3. Do not aim the LEDs directly at the eyes when the LEDs
are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
field-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Installation:
1. Run hidden cables from the video source and power
supply and connect to the camera. Do not cut the DC
jack or female BNC connector as this will void the
warranty. If needed, use the included SECO-LARM
DC plug with terminal block.
For flush mounting:
Use the included mounting template as a guide to
drill the necessary holes. Insert the camera into
the hole. Mount the camera to the wall using the
four included mounting screws.
2. Test the voltage from the power supply.
Use 12VDC or 24VAC.
3. Undo the hex screws on the side of the dome using the
included allen wrench and remove the dome and the
rubber ring from the camera and base.
5. Adjust the camera angle as needed. Use the
OSD control joystick to adjust the camera settings
(See the OSD manual). Connect a service
monitor to the service monitor port connector for
on-site adjustments.
4. For surface mounting:
6. To adjust zoom and focus, loosen the lock knobs
by hand or with a screwdriver. Slide left or right to
adjust. Do not use power tools. Lens damage
may result
7. Replace the rubber ring on the camera.
8. Reattach the dome to the camera.
9. Use the included allen wrench to tighten the set
screw, securing the dome to the base.
Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location with a
pencil. Mount the base to the wall or ceiling using the
four included mounting screws. If the wall is made of
brick, drywall, or similar material, it may be necessary
to use screw anchors (not included).
Mount the camera to the base using the base-mounting
10. Do a final test of the video camera and monitor.
screws.
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Elite 3X Vandal Dome Cameras for Flush or Surface Mount
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen is blank.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
IMPORTANT
Check that the correct power supply is in use.
Check that the correct power supply is in use.
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement
of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
E-mail: [email protected]
PIKHR1
16842 Millikan Avenue, Irvine, CA 92606
MiEV-2866-xLGxQ_1110.docx
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
4
SECO-LARM U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|