SECO LARM USA Home Security System EV 5120 N3WQ 480 TV User Guide |
Covert PIR Camera
(Non-Functioning PIR)
Manual
Model
Resolution
480 TV Lines
480 TV Lines
600 TV Lines
600 TV Lines
Video Output
NTSC
EV-5120-N3WQ
EV-5120-P3WQ
EV-5620-N3WQ
EV-5620-P3WQ
PAL
NTSC
PAL
Camera is covertly hidden in a
non-functioning PIR sensor housing
1/3” Sony Super HAD II CCD
3.7mm lens (78° viewing angle)
480 or 600 TV lines
Low current draw: 200mA
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Covert PIR Camera
Overview:
Slide camera
downward onto
the mounting
bracket
Important:
Do not cut the DC jack or the female BNC
connector as this will void the warranty.
Mounting bracket
Camera
Female BNC connector
DC Plug with terminal block
DC jack
Before Starting:
1. Please read this manual carefully and
keep it for future reference.
2. Use the camera within given temperature
and electrical limits.
3. Do not mount the camera where it is
exposed to rain or other moisture, or in
humid or dusty places.
5. Do not mount the camera in areas
exposed to radiation, strong magnetic
fields, or strong electrical signals.
6. Do not open or disassemble the camera.
There are no user-serviceable parts inside.
7. Do not drop the camera or subject it to
strong vibrations.
4. Do not point the camera at the sun. Heat
could damage the camera, even when
not in use.
Installation:
1. Run a 12VDC power supply wire and
a video cable with a male BNC
connector through the wall to where
the camera will be mounted.
2. Connect the camera’s video and
power cables.
3. Do a preliminary test of the camera to
ensure it will work properly at that
location.
pulling it downward, off the camera.
5. Partially screw a screw into the wall where
the top of the bracket should go. Slide the
bracket onto the screw. Finish securing
the top of the bracket to the wall.
6. Secure the bottom of the bracket to
the wall.
7. Attach the camera to the bracket by sliding
the camera downward.
8. Do a final test of the video camera and
monitor.
4. Remove the bracket (if attached)
by gently wiggling it while
SECO-LARM U.S.A., Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ENFORCER Covert PIR Camera
Troubleshooting:
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
The screen is blank.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image is dim
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image has poor contrast.
Change the position of the camera.
Change the position of the camera.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no user-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for
a period of two (2) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment
is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
E-mail: [email protected]
PISCN4
MiEV-5xx0-x3WQ_1108.docx
4
SECO-LARM U.S.A., Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|