OPERATOR’S MANUAL
7-1/4 in. LASER CIRCULAR SAW
DOUBLE INSULATED
CSB132L
Your circular saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Avoid accidental starting. Be sure switch is off
WARNING:
before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites
accidents.
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install
a polarized outlet. Do not change the plug in any way.
TOOL USE AND CARE
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing the tool. Such preventive safety measures reduce
the risk of starting the tool accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools, with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tools operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
Double insulation
eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
Avoid body contact with grounded surfaces such
as pipes, radiators, ranges, and refrigerators. There
is an increased risk of electric shock if your body is
grounded.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
When servicing a tool, use only identical replacement
SERVICE
parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel could result in a risk of injury.
SPECIFIC SAFETY RULES
Always use blades with correct size and shape
(diamond vs. round) arbor holes. Blades that do
not match the mounting hardware of the saw will run
eccentrically, causing loss of control.
DANGER! Keep hands away from cutting area and
blade. Keep your second hand on the auxiliary handle
or motor housing. If both hands are holding the saw,
they cannot be cut by the blade.
Keep your body positioned to either side of the saw
blade, but not in line with the saw blade. KICKBACK
could cause the saw to jump backwards. (See “Causes
And Operator Prevention Of Kickback” later.)
Never use damaged or incorrect blade washers
or bolts. The blade washers and bolts were specially
designedforthesawforoptimumperformanceandsafety
of operation.
Do not reach underneath the work. The guard cannot
protect you from the blade below the work.
CAUSES AND OPERATOR PREVENTION OF
KICKBACK:
Kickback is a sudden reaction to a pinched, bound, or
misaligned saw blade, causing an uncontrolled saw to lift
up and out of the workpiece toward the operator.
Checklowerguardforproperclosingbeforeeachuse.
Donotoperatesawiflowerguarddoesnotmovefreely
andcloseinstantly.Neverclamportiethelowerguard
into the open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower guard with the
retracting handle. Make sure it moves freely and does
not touch the blade or any other part, in all angles and
depths of cut.
Check the operation and condition of the lower guard
spring. If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a buildup of debris.
Lower guard should be retracted manually only for
special cuts, such as "Pocket Cuts" and "Compound
Cuts." Raise lower guard by retracting handle. As
soon as blade enters the material, lower guard must
be released. For all other sawing, the lower guard should
operate automatically.
Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.
Whenthebladeispinchedorboundtightlybythekerfclosing
down, the blade stalls and the motor reaction drives the unit
rapidly back toward the operator.
If the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
Kickbackistheresultoftoolmisuseand/orincorrectoperating
procedures or conditions and can be avoided by taking
proper precautions, as given below:
Maintain a firm grip with both hands on the saw and
position your body and arm to allow you to resist
KICKBACK forces. KICKBACK forces can be controlled
by the operator, if proper precautions are taken.
When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to a
completestop.Neverattempttoremovethesawfrom
the work or pull the saw backward while the blade is
in motion, or KICKBACK may occur. Investigate and
take corrective actions to eliminate the cause of blade
binding.
When restarting a saw in the workpiece, center the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If saw blade is binding,
it may walk up or KICKBACK from the workpiece as the
saw is restarted.
NEVER hold piece being cut in your hands or across
your leg. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the tool “live”
and shock the operator.
Support large panels to minimize the risk of blade
pinching and KICKBACK. Large panels tend to sag
under their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near the
edge of the panel.
When ripping, always use a rip fence or straight edge
guide. Thisimprovestheaccuracyofthecutandreduces
the chance for blade binding.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
Do not use dull or damaged blade. Unsharpened or
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product
will draw. A wire gage size (A.W.G.) of at least 12 is
recommended for an extension cord 50 feet or
less in length. A cord exceeding 100 feet is not
recommended. If in doubt, use the next heavier gage.
The smaller the gage number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
improperly set blades produce narrow kerf which causes
excessive friction, blade binding and KICKBACK.
Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If blade
adjustment shifts while cutting, it may cause binding and
KICKBACK.
Use extra caution when making a “Pocket Cut” into
existingwallsorotherblindareas.Theprotrudingblade
may cut objects that can cause KICKBACK.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Know your power tool. Read operator’s manual
carefully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Ifthepowersupplycordisdamaged,itmustbereplaced
only by the manufacturer or by an authorized service
center to avoid risk.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety
glasses. Following this rule will reduce the risk of serious
personal injury.
LASER GUIDE WARNINGS:
Avoid direct eye exposure when using the laser guide.
The laser shall be used and maintained in accordance
with the manufacturer’s instructions.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Never aim the beam at a person or object other than the
workpiece.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Always ensure the laser beam is aimed at a sturdy
workpiece without reflective surfaces. Shiny reflective
sheet metal or similar shiny materials are not suitable for
laser use.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
All repairs should be made by an authorized service
representative or the laser manufacturer.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Power
Watt
min
Minutes
Time
Alternating Current
Direct Current
No Load Speed
Class II Tool
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
n
o
.../min
Per Minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in serious
personal injury.
Failure to keep your hands away from the blade will result in serious
personal injury.
To reduce the risk of injury or damage, avoid contact with any hot
surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When
servicing, use only identical replacement parts.
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual. If you
do not understand the warnings and instructions in the
operator’s manual, do not use this product. Call Ryobi
customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a product , use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
The double insulated system is intended to protect
the user from shock resulting from a break in the tool’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE:Servicingofaproductwithdoubleinsulationrequires
extreme care and knowledge of the system and should
be performed only by a qualified service technician. For
service, we suggest you return the product to your nearest
authorized service center for repair. Always use original
factory replacement parts when servicing.
**Ampere rating (on product data plate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
ELECTRICAL CONNECTION
100'
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, 60 Hz,
AC only (normal household current). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are working
with a power tool. Failure to do so can result in serious
personal injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Input............................ 120 V, 60 Hz, AC Only, 13 Amps
No Load Speed.................................5,500 r/min. (RPM)
Net Weight...........................................................12 lbs.
Laser Guide ....................Class IIIa, <5mW max, 650nm
Blade Diameter................................................. 7-1/4 in.
Blade Arbor...........................................................5/8 in.
Cutting Depth at 0°........................................... 2-3/8 in.
Cutting Depth at 45°..................................... 1-13/16 in.
SPINDLE LOCK
BUTTON
SWITCH
LASER GUIDE
UPPER BLADE
GUARD
DEPTH
ADJUSTMENT
KNOB
BLADE
LOWER BLADE
GUARD
BASE
LASER GUIDE
HANDLE
LASER GUIDE
SWITCH
LOWER BLADE
GUARD HANDLE
MOTOR HOUSING
EDGE GUIDE
KNOB
BEVEL
ADJUSTMENT
KNOB
Fig. 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR LASER CIRCULAR SAW
SPINDLE LOCK
Thespindlelockallowsyoutosecurethebladewhenturning
the blade screw.
See Figure 1.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all
operating features and safety rules.
SWITCH
The circular saw is equipped with a pre-travel safety switch
which reduces the possibility of accidental starting. When
you depress the switch, the saw will not start until you reach
the pre-travel position. You must depress the switch fully to
activate the saw.
ERGONOMIC DESIGN
The design of your circular saw provides for maintaining
proper two hand control when cutting. It has been designed
to be comfortable and easy to grasp.
LASER GUIDE
The laser guide will generate a red line on the work surface
when turned on.
ASSEMBLY
UNPACKING
This product requires assembly.
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to heed
this warning could result in serious personal injury.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
WARNING:
Do not discard the packing material until you have carefully
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Circular Saw with Laser
7-1/4 in. Blade
WARNING:
AAA Batteries (2)
Wrench
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
Operator’s Manual
WARNING:
A 7-1/4 in. blade is the maximum blade capacity of
the saw. Also, never use a blade that is too thick to
allow outer blade washer to engage with the flat on the
spindle. Larger blades will come in contact with the blade
guards, while thicker blades will prevent blade screw from
securing blade on spindle. Either of these situations could
result in a serious accident.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
CAUTION:
SPINDLE
BLADE
To prevent damage to the spindle or spindle lock, always
allow motor to come to a complete stop before engaging
spindle lock.
OUTER BLADE
WASHER (“D”
WASHER)
ATTACHING BLADE
See Figures 2 - 3.
BLADE
Unplug the saw.
SCREW
Depress and hold spindle lock.
INNER
FLANGE
BUSHING
Remove blade screw by turning it counterclockwise with
the provided wrench, while keeping the spindle lock
depressed.
SPRING
WASHER
Remove spring washer and outer blade washer (“D”
Fig. 2
washer).
OUTER BLADE WASHER
(“D” WASHER)
WARNING:
If inner flange bushing has been removed, replace it
before placing blade on spindle. Failure to do so could
cause an accident since blade will not tighten properly.
Retract the lower blade guard into the upper blade guard
using the lower blade guard handle. Make sure the lower
guard spring works properly, allowing the guard to move
freely.
CUPPED SIDE OF OUTSIDE OF SPRING
SPRING WASHER
WASHER
Check to see that the saw teeth and arrow on the saw
blade and the arrow on the lower guard are pointing in
the same direction.
Fig. 3
NOTE: The saw teeth point upward at the front of the
saw as shown.
SPINDLE LOCK
BUTTON
Fit the saw blade inside the lower blade guard and onto
the spindle.
Reinstall “D” washer.
Reinstall spring washer.
Depress and hold spindle lock and replace blade
screw.
Tighten blade screw securely by turning it clockwise with
the wrench.
NOTE: Never use a blade that is too thick to allow the
“D” washer to engage with the flat on the spindle.
BLADE
SCREW
REMOVING BLADE
See Figure 4.
WRENCH
Fig. 4
Unplug the saw.
Depress and hold spindle lock.
Remove blade screw by turning it counterclockwise with
the provided wrench, while keeping the spindle lock
depressed.
Remove spring washer and outer blade washer (“D”
washer).
Lift lower blade guard.
Remove blade.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
KICKBACK - BLADE SET TOO DEEP
Fig. 5
INCORRECT
SUPPORT
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Cutting all types of wood products (lumber, plywood,
paneling)
Fig. 6
Cross Cutting/Rip Cutting
Bevel Cutting
Pocket Cutting
KICKBACK
See Figures 5 - 8.
Kickback occurs when the blade stalls rapidly and the saw
is driven back towards you. Blade stalling is caused by any
action which pinches the blade in the wood.
DANGER:
CORRECT BLADE DEPTH SETTING = BLADE EXPOSED 1/4 in.
OR LESS ON UNDERSIDE OF WORKPIECE
Release switch immediately if blade binds or saw stalls.
Kickback could cause you to lose control of the saw. Loss
of control can lead to serious injury.
Fig. 7
To guard against kickback, avoid dangerous practices such
as the following.
CORRECT
SUPPORT
Setting blade depth incorrectly.
Sawing into knots or nails in workpiece.
Twisting the blade while making a cut.
Making a cut with a dull, gummed up, or improperly set
blade.
Supporting the workpiece incorrectly.
Forcing a cut.
Cutting warped or wet lumber.
Operating the tool incorrectly or misusing the tool.
Fig. 8
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
To lessen the chance of kickback, follow these safety
practices.
Keep the blade at the correct depth setting. The depth
setting should not exceed 1/4 in. below the material being
cut.
Inspect the workpiece for knots or nails before cutting.
Never saw into a knot or nail.
Make straight cuts. Always use a straight edge guide
when rip cutting. This helps prevent twisting the blade.
Use clean, sharp, and properly set blades. Never make
cuts with dull blades.
Support the workpiece properly before beginning a cut.
LOWER BLADE GUARD
IS IN UP POSITION
WHEN MAKING A CUT
Use steady, even pressure when making a cut. Never
Fig. 9
force a cut.
Do not cut warped or wet lumber.
Hold the saw firmly with both hands and keep your body
in a balanced position so as to resist the forces if kickback
should occur.
DANGER:
When sawing through work, lower blade guard does not
cover blade on the underside of work. Since blade is
exposed on underside of work, keep hands and fingers
away from cutting area. Any part of your body coming in
contact with moving blade will result in serious injury.
WARNING:
When using the saw, always stay alert and exercise
control. Do not remove the saw from the workpiece while
the blade is moving.
CAUTION:
SAW BLADES
The best of saw blades will not cut efficiently if they are not
kept clean, sharp, and properly set. Using a dull blade will
place a heavy load on the saw and increase the danger of
kickback. Keep extra blades on hand so that sharp blades
are always available.
Never use saw when guard is not operating correctly.
Check the guard for correct operation before each use.
The guard is operating correctly when it moves freely and
readily returns to the closed position. If you drop the saw,
check the lower blade guard and bumper for damage at
all depth settings before reuse.
Gum and wood pitch hardened on blades will slow the
saw down. Remove saw blade from the saw and use gum
and pitch remover, hot water, or kerosene to remove these
accumulations. DO NOT USE GASOLINE.
BLADE GUARD SYSTEM
See Figure 9.
The lower blade guard attached to the circular saw is there
for your protection and safety. Do not alter it for any reason.
If it becomes damaged, do not operate the saw until you
have the guard repaired or replaced. Always leave guard in
operating position when using the saw.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ADJUSTING BLADE DEPTH
See Figure 10.
DEPTH OF CUT
SCALE
Always keep correct blade depth setting. The correct blade
depth setting for all cuts should not exceed 1/4 in. below
the material being cut. More blade depth will increase the
chance of kickback and cause the cut to be rough. For
more depth of cut accuracy, a scale is located on the upper
blade guard.
Unplug the saw.
WARNING:
Failure to unplug the tool could result in accidental
starting causing serious injury.
BASE
Loosen depth adjustment knob.
DEPTH
ADJUSTMENT
KNOB
Determine the desired depth of cut.
Locate depth of cut scale on back of upper blade
Fig. 10
guard.
Hold base flat against the workpiece and raise or lower
saw until the indicator mark on bracket aligns with notch
on blade guard.
SWITCH
Tighten depth adjustment knob securely.
STARTING/STOPPING THE SAW
See Figure 11.
To start the saw: Depress the switch trigger.
Always let the blade reach full speed, then guide the saw
into the workpiece.
WARNING:
The blade coming in contact with the workpiece before
it reaches full speed could cause the saw to “kickback”
towards you resulting in serious injury.
Fig. 11
To stop the saw: Release the switch trigger.
After you release the switch trigger, allow the blade to come
to a complete stop. Do not remove the saw from the
workpiece while the blade is moving.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING THE SAW
See Figures 12 - 14.
Itisimportanttounderstandthecorrectmethodforoperating
thesaw.Refertothefiguresinthissectiontolearnthecorrect
and incorrect ways for handling the saw.
WARNING:
To make sawing easier and safer, always maintain proper
control of the saw. Loss of control could cause an
accident resulting in possible serious injury.
DANGER:
When lifting the saw from the workpiece, the blade is
exposed on the underside of the saw until the lower blade
guard closes. Make sure the lower blade guard is closed
before setting the saw down.
Fig. 12
To make the best possible cut, follow these helpful hints.
Hold the saw firmly with both hands.
Avoid placing your hand on the workpiece while making
a cut.
Support the workpiece so that the cut is always on your
right.
Support the workpiece near the cut.
Clamp the workpiece securely so that the workpiece will
not move during the cut.
Avoid placing the saw on the part of the workpiece that
will fall off when the cut is made.
Place the workpiece with the “good” side down.
Draw a guideline along the desired line of cut before
beginning your cut.
Keep the cord away from the cutting area. Always place
the cord to prevent it from hanging up on the workpiece
while making a cut.
Fig. 13
DANGER:
If the cord hangs up on the workpiece during a cut,
release the switch trigger immediately. Unplug the saw
and reposition the cord to prevent it from hanging up
again.
DANGER:
Using a saw with a damaged cord could result in serious
injury or death. If the cord has been damaged, have it
replaced before using the saw again.
Fig. 14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CROSS CUTTING/RIP CUTTING
See Figure 15.
TOP VIEW OF SAW
When making a cross cut or rip cut, align the line of cut
with the outer blade guide notch on the base as shown in
the figure.
Sincebladethicknessesvary,alwaysmakeatrialcutinscrap
materialalongaguidelinetodeterminehowmuch, ifany, you
must offset the guideline to produce an accurate cut.
BLADE GUIDE
NOTCH
NOTE: The distance from the line of cut to the guideline is
the amount you should offset the guide.
TO RIP CUT
See Figures 16 - 17.
Use a guide when making long or wide rip cuts with the
saw.
GUIDELINE
Fig. 15
To rip cut using optional edge guide:
Slide edge guide into the slot.
Align the guideline with the blade guide notch on the
base.
Adjust the guide so that the “0” on the guide is aligned
WORKPIECE
with the edge of the workpiece.
Secure the guide with the lock knob provided with the
saw.
Secure the workpiece.
Position the face of the edge guide firmly against the edge
of workpiece.
NOTE: The guiding edge of the workpiece must be
straight for your cut to be straight. Use caution to prevent
the blade from binding in the cut.
GUIDELINE
Saw along workpiece keeping guide firmly against edge
to achieve a straight rip cut.
EDGE GUIDE
To rip cut using a straight edge:
Fig. 16
Secure the workpiece.
Clamp a straight edge to the workpiece using
C-clamps.
NOTE: Position C-clamps so they will not interfere with
the saw housing during the cut.
C-CLAMPS
Saw along the straight edge to achieve a straight rip
cut.
STRAIGHT
EDGE
NOTE: Do not bind the blade in the cut.
GUIDELINE
WORKPIECE
Fig. 17
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LENGTH OF CUT SCALE
See Figure 18.
The saw is equipped with a length of cut scale on its base. It
is parallel with the saw blade and you can use it to measure
the distance into the material the blade cuts.
NOTE: Six inches is the maximum length of cut that you can
measure. Also, it is accurate only when the depth of cut is
set at full maximum depth.
USING THE LASER GUIDE
See Figure 19.
WARNING:
Do not stare into the laser beam or turn the laser on when
the tool is not in use. Failure to heed this warning could
result in serious personal injury. The laser unit comes
from the factory already installed and aligned. If the laser
becomes misaligned after time, refer to the Adjustments
section.
LENGTH OF CUT
SCALE
Fig. 18
LASER GUIDE
SWITCH
ON(I)/OFF(O)
Mark the line to be cut on the workpiece.
Adjust the depth and angle of the cut as needed.
Switch ON (I) the laser beam.
Plug the tool into a power supply and start the motor.
NOTE: Do not touch the blade to the workpiece until the
saw has reached maximum speed.
Slowly push the saw forward into the workpiece.
NOTE: Keep the laser beam on the marked line on the
workpiece for precision cutting.
Once the cut is complete, allow the saw to come to a
complete stop before turning off the laser.
Unplug the saw.
Fig. 19
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
BEVEL CUTTING
See Figures 20 - 21.
MOTOR
HOUSING
To make the best possible cut, follow these helpful hints.
Align the line of cut with the inner blade guide notch on
the base when making 45° bevel cuts.
Make a trial cut in scrap material along a guideline to
determine how much you should offset the guideline on
the cutting material.
Adjust the angle of the cut to any desired setting between
BEVEL SCALE
zero and 51.5°. Refer to To adjust bevel setting next.
TO ADJUST BEVEL SETTING
See Figure 20.
Unplug the circular saw.
WARNING:
Failure to unplug the tool could result in accidental
starting causing serious injury.
BEVEL
ADJUSTMENT
KNOB
BLADE GUIDE NOTCH
Fig. 20
Loosen bevel adjustment knob.
Raise motor housing end of saw until you reach desired
angle setting on bevel scale.
Tighten bevel adjustment knob securely.
WARNING:
Attempting a bevel cut without having the bevel
adjustment knob securely tightened can result in serious
injury.
TO BEVEL CUT
See Figure 21.
Hold the saw firmly with both hands as shown.
Rest the front edge of the base on the workpiece.
Start the saw and let the blade reach full speed.
Guide the saw into the workpiece and make the cut.
Release the trigger and allow the blade to come to a
Fig. 21
complete stop.
Lift the saw from the workpiece.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
POCKET CUTTING
See Figure 22.
WARNING:
LOWER
BLADE
GUARD
Always adjust bevel setting to zero before making a
pocket cut. Attempting a pocket cut at any other setting
can result in loss of control of the saw possibly causing
serious injury.
Adjust the bevel setting to zero.
Set the blade to the correct blade depth setting.
Swing the lower blade guard up using the lower blade
guard handle.
NOTE: Always raise the lower blade guard with the handle
to avoid serious injury.
LOWER BLADE
GUARD HANDLE
POCKET
CUT
Hold the lower blade guard by the handle.
Rest the front of the base flat against the workpiece with
the rear of the handle raised so the blade does not touch
the workpiece.
Fig. 22
Start the saw and let the blade reach full speed.
Guide the saw into the workpiece and make the cut.
WARNING:
Always cut in a forward direction when pocket cutting.
Cutting in the reverse direction could cause the saw to
climb up on the workpiece and back toward you.
Release the trigger and allow the blade to come to a
complete stop.
Lift the saw from the workpiece.
Clear corners out with a hand saw or sabre saw.
WARNING:
Never tie the lower blade guard in a raised position.
Leaving the blade exposed could lead to serious injury.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
DANGER:
DO NOT point the laser at yourself or others. Class IIIa
lasers will burn the retinas and could cause serious injury
to the eyes.
LASER
COVER
WARNING:
Before performing any adjustment, make sure the tool
is unplugged from the power supply and the switch is in
the OFF (O) position. Failure to heed this warning could
result in serious personal injury.
SCREW
WARNING:
Use of controls or adjustments or performance other
than those specified herein could result in hazardous
radiation exposure.
ADJUSTING THE LASER
See Figure 23.
Unplug the circular saw.
Make sure laser is turned off.
Remove the laser cover by lifting it off its base.
Turn laser on.
Loosen the screw inside laser.
Rest the front of the base on scrap workpiece.
Fig. 23
Adjust the laser beam with the mark on the scrap
workpiece by loosening the screw to the laser aperture
and slowly moving laser guide left or right.
Since blade thicknesses vary, always make a trial cut in
scrap workpiece to ensure an accurate cut.
Once alignment is achieved tighten the screw.
Replace the laser cover.
Check for proper alignment.
Repeat as necessary until laser is aligned.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
0° BEVEL STOP
See Figure 24.
Thesawhasa 0°bevelstopthathasbeenfactoryadjustedto
assure 0° angle of the saw blade when making 90° cuts.
TO CHECK 0° BEVEL STOP
Unplug the circular saw.
BEVEL
ADJUSTMENT KNOB
Place the saw in an upside down position on a
workbench.
Check the squareness of the saw blade to the base of
the saw using a carpenter’s square.
CARPENTER’S
SQUARE
TO ADJUST 0° BEVEL STOP
Unplug the circular saw.
Loosen bevel adjustment knob.
Turn set screw with hex key and adjust base until it is
square with the saw blade.
Tighten bevel adjustment knob securely.
WARNING:
Attempting a bevel cut without having the bevel
adjustment knob securely tightened can result in serious
injury.
SET SCREW
Fig. 24
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING LASER GUIDE BATTERIES
See Figure 25.
WARNING:
Unplug the saw.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
Make sure laser is turned off.
Remove the laser cover by lifting it off its base.
Remove both AAA batteries.
Install the two AAA batteries aligning the positives (+)
with positives (+) and the negatives (-) with negatives (-)
as shown on the inside base of laser.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
Replace the laser cover.
Turn on laser.
GENERAL MAINTENANCE
CAUTION:
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Use of controls or adjustments or performance other than
those specified herein may result in hazardous radiation
exposure.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Electrictoolsusedonfiberglassmaterial,wallboard,spackling
compounds, or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently, we do not recommended
usingthistoolforextendedworkonthesetypesofmaterials.
However, if you do work with any of these materials, it is
extremely important to clean the tool using compressed
air.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normaloperatingconditions.Therefore,nofurtherlubrication
is required.
Fig. 25
22
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
7-1/4 in. LASER CIRCULAR SAW
DOUBLE INSULATED
CSB132L
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter out microscopic particles.
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
CSB132L
• MODEL NUMBER
• SERIAL NUMBER
• HOW TO OBTAIN REPLACEMENT PARTS:
1-800-525-2579. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
1-800-525-2579.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
RYOBI® is a registered trademark of Ryobi Limited used under license.
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-525-2579
987000-113
4-20-07 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|