OPERATOR'S MANUAL
10 in. BAND SAW
BS1001SV
Your new Band Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation,
and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
nDO NOT OVERREACH. Keep proper footing and balance
WARNING:
at all times.
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
nMAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for best and safest performance. Follow instructions
for lubricating and changing accessories.
nDISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected from power
source.
READ ALL INSTRUCTIONS
nKNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the applications and limitations
as well as specific potential hazards related to this tool.
nGUARD AGAINST ELECTRICAL SHOCK by prevent-
ing body contact with grounded surfaces. For example:
pipes, radiators, ranges, refrigerator enclosures.
nKEEP GUARDS IN PLACE and in working order. Never
operate the tool with any guard or cover removed. Make
sure all guards are operating properly before each use.
nREDUCE THE RISK OF UNINTENTIONAL STARTING.
Be sure switch is off when plugging in.
nUSE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may cause risk of injury.
nNEVER STAND ON TOOL. Serious injury could oc-
cur if the tool is tipped or if the blade is unintentionally
contacted.
nREMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see keys and adjusting wrenches are
removed from tool before turning it on.
nCHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
nKEEP THE WORK AREA CLEAN. Cluttered work areas
and work benches invite accidents.
nDON’T USE IN DANGEROUS ENVIRONMENTS. Do not
use power tools near gasoline or other flammable liquids,
in damp or wet locations or expose them to rain. Keep
work area well lighted.
nKEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area.
nDIRECTION OF FEED. Feed work into a blade or cutter
against the direction or rotation of the blade or cutter
only.
nMAKE WORKSHOP CHILDPROOF with padlocks,
nNEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
master switches, or by removing starter keys.
nDON’T FORCE THE TOOL. It will do the job better and
safer at the rate for which it was designed.
nDON’T ABUSE CORD. Never carry tool by the cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
nUSE THE RIGHT TOOL. Do not force the tool or attach-
ment to do a job for which it was not designed.
nUSE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating. A wire gauge size (A.W.G.) of at
least 14 is recommended for an extension cord 25 feet
or less in length. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
nWEAR PROPER APPAREL. Do not wear loose clothing,
neckties, or jewelry that can get caught in the tool’s mov-
ing parts and cause personal injury. Nonslip footwear is
recommended when working outdoors. Wear protective
hair covering to contain long hair.
nPROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
nPROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
nBLADE COASTS AFTER TURN OFF.
nKEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
nINSPECT TOOL CORDS AND EXTENSION CORDS
PERIODICALLY and, if damaged, have repaired by a
qualified service technician. Stay constantly aware of cord
location and keep it well away from the rotating wheel.
nALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-resis-
tant lenses; they are NOT safety glasses.
nNEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal
sparking of the motor could ignite fumes.
nUSE ONLY OUTDOOR EXTENSION CORDS with ap-
proved ground connection that are intended for use
outdoors and so marked.
nSECURE WORK. Use clamps or a vise to hold work when
practical. It’s safer than using your hand and it frees both
hands to operate tool.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
nBE SURE THE BLADE PATH IS FREE OF NAILS. Inspect
for and remove nails from lumber before cutting.
nDO NOT REMOVE JAMMED CUTOFF PIECES until
blade has stopped.
nAVOID AWKWARD OPERATIONS AND HAND nNEVER START THE TOOL when the blade is in contact
with the workpiece.
POSITIONS where a sudden slip could cause your hand
to move into the blade. ALWAYS make sure you have
good balance.
nNEVER TOUCH BLADE or other moving parts during
use.
nALLOW THE MOTOR TO COME UP TO FULL SPEED
nBEFORE CHANGING THE SETUP, REMOVING
COVERS, GUARDS OR BLADES, unplug the saw and
remove the switch key.
before starting a cut to avoid binding or stalling.
nDO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
nHOLD THE WORKPIECE firmly against the saw table.
nTO AVOID ACCIDENTAL BLADE CONTACT, minimize
blade breakage, and provide maximum blade support,
always adjust the blade guide assembly to just clear the
workpiece.
nREPLACEMENT PARTS. All repairs, whether electrical
or mechanical, should be made by a qualified service
technician at an authorized service center.
nWHEN SERVICING use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause
product damage.
nKEEP BLADES CLEAN, SHARP, AND WITH
SUFFICIENT SET. Sharp blades minimize stalling and
kickbacks.
nKEEP HANDS AWAY FROM CUTTING AREA. Do not nALWAYS TURN OFF SAW before disconnecting it to
hand hold pieces so small that your fingers go under
the blade guard. Do not reach underneath work or in
blade cutting path with your hands and fingers for any
reason.
avoid accidental starting when reconnecting to a power
source.
nDO NOT OPERATE THIS TOOL WHILE UNDER
THE INFLUENCE OF DRUGS, ALCOHOL OR ANY
MEDICATION.
nNEVER CUT MORE THAN ONE PIECE AT A TIME or
stack more than one workpiece on the saw table at a
time.
nSTAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
nFIRMLY CLAMP OR BOLT your saw to a stable, level
workbench or table. The most comfortable table height
is approximately waist height.
nMAKE SURE WORK AREA HAS AMPLE LIGHTING to
see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using your
saw.
nDO NOT FEED THE MATERIAL TOO QUICKLY. Do not
force the workpiece against the blade.
nTHE BLADE GUIDES HAVE BEEN PRESET AT THE
FACTORY. These settings are functional for some ap-
plications. We recommend that you check and adjust
blade guide settings before first use of your saw. Refer to
“Adjusting thrust bearings, blade guide support, and
blade guides” procedures explained in the Adjustments
section of this operator’s manual.
nUSE ONLY CORRECT BLADES. Use the right blade size,
style and cutting speed for the material and the type of
cut. Blade teeth should point down toward the table.
nBEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
nALWAYS SUPPORT LARGE WORKPIECES while cut-
ting to minimize risk of blade pinching and kickback.
Saw may slip, walk or slide while cutting large or heavy
boards.
nSAVE THESE INSTRUCTIONS. Refer to them frequently
and use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions
also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals, work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Hot Surface
To reduce the risk of injury or damage, avoid contact with
any hot surface.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand com-
pletely the operator’s manual. Save this operator’s manual
and review frequently for continuing safe operation and
instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Resaw
Bevel Cut
A cutting operation to reduce the thickness of the workpiece
A cutting operation made with the saw table at any angle
to make thinner pieces.
other than 90° to the blade.
Resin
Compound Cut
A sticky, sap-based substance that has hardened.
A compound cut is a cut made using a miter angle and a
bevel angle at the same time.
Ripping
Crosscut
A cutting operation along the length of the workpiece.
A cutting or shaping operation made across the grain or the
width of the workpiece.
Saw Blade Path
The area directly in line — over, under, behind or in front of
the blade. As it applies to the workpiece, that area which
will be or has been cut by the blade.
FPM
3,000 surface feet per minute, used in reference to surface
speed of blade.
Set
Freehand (for band saw)
Performing a cut without the workpiece properly supported
on the saw table.
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Throw-Back
Gum
Saw throwing back a workpiece in a manner similar to a
kickback. Usually associated with a cause other than the kerf
closing, such as a workpiece being dropped into the blade
or being placed inadvertently in contact with the blade.
A sticky, sap-based residue from wood products.
Kerf
The material removed by the blade in a through cut or the slot
produced by the blade in a non-through cut or partial cut.
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Kickback
A hazard that can occur when the blade binds or stalls,
throwing the workpiece back toward operator.
Workpiece
The item on which the cutting operation is being done. The
surfaces of a workpiece are commonly referred to as faces,
ends, and edges.
Leading End
The end of the workpiece pushed into the cutting tool
first.
Worktable
Miter Cut
The surface on which the workpiece rests while performing
a cutting or sanding operation.
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
Push Stick
A device used to feed the workpiece through the saw blade
during narrow cutting operations. It helps keep the operator's
hands well away from the blade.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
EXTENSION CORDS
SPEED AND WIRING
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool's plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
The no-load speed of this tool is approximately 3,000
FPM. This speed is not constant and decreases under
a load or with lower voltage. For voltage, the wiring in a
shop is as important as the motor’s horsepower rating. A
line intended only for lights cannot properly carry a power
tool motor. Wire that is heavy enough for a short distance
will be too light for a greater distance. A line that can
support one power tool may not be able to support two
or three tools.
GROUNDING INSTRUCTIONS
**Ampere rating (on tool faceplate)
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding conduc-
tor and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100'
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or with-
out yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the let-
ters "WA" on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
WARNING:
Keep the extension cord clear of the working area. Po-
sition the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet
like the one shown in figure 1. It also has a grounding pin
like the one shown.
WARNING:
Check extension cords before each use. If damaged re-
place immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 volts,
60 Hz, AC only (normal household current). Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If the
saw does not operate when plugged into an outlet, double
check the power supply.
GROUNDING
PIN
COVER OF GROUNDED
OUTLET BOX
Fig. 1
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Blade Width.................. 1/8 in. to 1/2 in. (3 mm to 13 mm)
Blade Length...........................................67 in. (1702 mm)
Frame to Blade Capacity...........................10 in. (254 mm)
Cutting Thickness Capacity .....................4 in. (101.6 mm)
Table Size (extended) .............................13 in. x 26-1/2 in.
(330 mm x 673.1 mm)
Input ...............................120 Volt, 60Hz, AC Only, 8 Amps
No Load Speed ................................................. 3,000 FPM
Dust Port ............................................ 2-1/4 in. (57.15 mm)
Net Weight................................................. 82 lbs. (37.2 kg)
RAPIDSET™ BLADE
TRACKING
TENSION LEVER
KNOB
DUST BAG
BLADE
GUIDE
KNOB
BLADE GUIDE
LOCK KNOB
THROAT
PLATE
SAW TABLE
BLADE TENSION
BEVEL LOCK
KNOB
KNOB
LATCH
SCALE
TRACKING
VIEW WINDOW
BEVEL
ADJUSTMENT
KNOB
SWITCH
AND
SWITCH KEY
BLADE
GUARD
SCALE
INDICATOR
SAW BLADE
RIP
FENCE
MITER
GAUGE
DUST
EXHAUST
PORT
LED SWITCH
LED LIGHTING
EXTENSION
TABLE
BLADE GUIDE
BEARING
SAW
TABLE
Fig. 2
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR BAND SAW
LED LIGHTING
See Figure 2.
Your band saw comes equipped with LED lighting that lights
the work area for safer, more accurate cuts.
Before attempting to use, familiarize yourself with all the
operating features and safety requirements of your saw.
MITER GAUGE
This gauge aligns the wood for a crosscut. The easy-to-read
BLADE GUIDE BEARINGS
Upper and lower blade guides bearings help keep the blade
indicator shows the exact angle for a miter cut.
from twisting during operation.
RIP FENCE
BEVEL ADJUSTMENT KNOB
Tilts the saw table for bevel cutting.
A sturdy metal fence guides the workpiece and is secured
with the rip fence handle.
BEVEL LOCK KNOB
SAW BLADE
Loosening the bevel lock knob allows the saw table to be
tilted at different angles. Tightening the bevel lock knob locks
the saw table in place.
Saw comes with a standard 1/4 in. (6 mm) blade and a
3/8 in. (10 mm) blade.
SAW TABLE WITH THROAT PLATE
BLADE GUIDE KNOB WITH BLADE GUIDE
LOCK KNOB
Use the blade guide knob and blade guide lock knob to
adjust the blade guide assembly to keep the blade from
twisting or breaking. Always lock the blade guide assembly
in place before turning on the band saw.
Your band saw has an aluminum saw table with tilt control
for maximum accuracy. The throat plate, installed in the saw
table at the factory, allows for blade clearance.
SCALE AND SCALE INDICATOR
The scale and scale indicator show the angle or degree the
saw table is tilted for bevel cutting.
BLADE GUARD
SWITCH AND SWITCH KEY
Protects the operator from coming in contact with the
blade.
Your band saw has an easy access power switch. To lock
in the OFF position, remove the yellow switch key. Place
the key in a location inaccessible to children and others not
qualified to use the tool.
BLADE TENSION KNOB
Controls blade tension when changing blades and making
adjustments for various sawing applications.
TRACKING KNOB
Adjusts tracking to keep blade centered on the wheels.
DUST EXHAUST PORT
A 2-1/4 in. (57.15 mm) dust exhaust port makes dustless cut-
ting possible by blowing the dust away from the user. Attach
the dust bag or a shop vac to the dust exhaust port.
TRACKING VIEW WINDOW
The tracking view window is equipped with a light that makes
tracking adjustments easier to see.
LATCH
Easy open latches allow front cover to be opened for
making adjustments.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS NEEDED
The following tools (not included) are needed for assembly and alignment:
10 mm WRENCH
PHILLIPS SCREWDRIVER
COMBINATION
SQUARE
Fig. 3
LOOSE PARTS LIST
The following items are included with your band saw:
Hex Key, 3 mm..................................................................1
Rip Fence ..........................................................................1
Miter Gauge.......................................................................1
Saw Table..........................................................................1
Extension Table .................................................................1
Wing Nut............................................................................1
Dust Bag............................................................................1
Table Aligning Bolt.............................................................1
Screw, Flat Head ...............................................................4
3/8 in. (10 mm) Saw Blade ................................................1
Washer ..............................................................................1
Switch Key ........................................................................1
Operator’s Manual (not shown) .........................................1
SAW TABLE
RIP FENCE
EXTENSION
TABLE
MITER GAUGE
DUST BAG
SAW
BLADE
SWITCH
KEY
TABLE ALIGNING
BOLT
FLAT
HEAD
SCREW
WASHER
WING
NUT
3 mm HEX KEY
Fig. 4
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS LIST
The following items are included with your band saw:
Legs.................................................................................................................................................................................4
Feet .................................................................................................................................................................................4
Mounting Bolts................................................................................................................................................................3
Flat Washers....................................................................................................................................................................3
Hex Nuts..........................................................................................................................................................................3
Side Brace (right).............................................................................................................................................................1
Side Brace (left)...............................................................................................................................................................1
Top Brace (front and back)..............................................................................................................................................2
Leg Brace, Long..............................................................................................................................................................2
Leg Brace, Short ............................................................................................................................................................2
Carriage Bolts................................................................................................................................................................16
Hex Nuts........................................................................................................................................................................16
Carriage Bolts, small .......................................................................................................................................................4
Hex Nuts, small ...............................................................................................................................................................4
TOP BRACE
CARRIAGE
(BACK)
BOLT, SMALL
TOP BRACE
(LEFT)
TOP BRACE
(FRONT)
LEG BRACE
(LONG)
HEX NUT,
SMALL
LEG BRACE
(SHORT)
TOP BRACE
(RIGHT)
LEG
HEX NUT
CARRIAGE
BOLT
LEG BRACE
(SHORT)
LEG BRACE
(LONG)
HEX NUT
WASHER
FEET
MOUNTING BOLT
Fig. 5
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
n Align the holes on the brace and the legs. Insert two
UNPACKING
This product requires assembly.
carriage bolts and hand tighten using hex nuts. These
are the front and back sets.
n Carefully remove the tool and any accessories from the
box. Place it on a level work surface.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n For the side sets, install a side brace on two legs. Add
hardware and finger tighten. Repeat for the other side
brace. See Figure 7.
HEX NUT
n Do not discard the packing material until you have
carefully inspected the tool, identified all loose parts,
and satisfactorily operated the tool.
n If any parts are damaged or missing, please call 1-800-
525-2579 for assistance.
TOP BRACE
CARRIAGE
BOLT
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
TOP BRACE
WARNING:
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
Fig. 6
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
CARRIAGE
BOLT
HEX NUT
Assembly is best done in the area where the saw will be
used. When you remove the table saw base, loose parts,
and hardware from the packing materials, check all items
with the loose parts list and drawing. If you are unsure about
the description of any part, refer to the drawing. If any parts
are missing, delay assembling until you have obtained the
missing part(s).
ASSEMBLING LEG STAND
See Figures 6 and 7.
n Locate the following hardware:
16 carriage bolts
4 carriage bolts, small
16 hex nuts
4 hex nuts, small
4 feet
LEG BRACE
(LONG)
n Take 4 legs and 8 braces from loose parts.
n Place top braces inside legs.
Fig. 7
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
n Use the same steps to install the lower braces. Tighten
all hex nuts with a wrench.
n Place a carriage bolt in each of the four holes on the top
of the leg stand and secure with a hex nut.
n Tighten securely.
HEX NUT
WASHER
n Place one foot on the bottom of each of the legs.
n Move the leg set to desired location.
TO MOUNT THE BAND SAW TO THE LEG
STAND
See Figure 8.
nTake the following from a small hardware bag:
HOLES IN
SAW BASE
3 hex bolts
3 hex nuts
3 flat washers
NOTE: This hardware was in the bag with hardware for
assembling the leg stand.
WARNING:
The saw base is heavy. Do not lift the saw without help.
When lifting, lift close to your body. Keep your knees
bent and lift with your legs, not your back. Ignoring these
precautions can result in back injury.
HEX NUT
FLAT
WASHER
MOUNTING
BOLT
n Place the band saw on the leg stand. Align the holes in
the saw base with the holes in the upper braces.
SAW BASE
LEG STAND
n Place a flat washer on a hex bolt and insert through hole.
Add a hex nut. Hand tighten. See Figure 9.
n Repeat for remaining holes. Tighten all hardware with a
wrench. You may find it helpful to use one wrench to hold
the head of the hex bolt and one to tighten the hex nut.
MOUNTING BOLT
Fig. 8
TO MOUNT THE SAW TABLE
SAW
TABLE
See Figures 9 - 10.
SCREW
n Standing at the front of the band saw, slide the saw table
(past the blade) through the slot moving from the left side
of the saw table to the right.
n Align the screw holes in the saw table with the holes in
the saw table bracket.
n Using the screws, attach the saw table to the saw table
bracket. Tighten phillips screws securely.
n Attach the table aligning bolt, washer, and wing nut to
the saw table.
NOTE: The wing nut and washer goes below the saw
table.
SAW TABLE
BRACKET
Fig. 9
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO SQUARE THE SAW TABLE TO THE BLADE
LOCK KNOB
See Figure 11.
TABLE
ALIGNING
BOLT
n Turn the blade guide lock knob counterclockwise to
unlock the blade guide assembly. Turning the blade guide
knob clockwise, raise the blade guide assembly as far as
it will go. Turn the lock knob clockwise to retighten.
BLADE GUIDE
KNOB
n Place a small combination square on the saw table beside
the blade.
n Loosen the bevel lock knob and rotate the bevel
adjustment knob to tilt the saw table up or down to align
table 90° to blade (0° position). Retighten the bevel lock
knob.
WASHER
n Using a hex key, adjust the zero stop set screw until the
set screw just touches the saw housing.
n Check squareness of the saw table to the blade. Make
readjustments if necessary.
WING
NUT
n Loosen screw on scale indicator with a phillips screwdriver
and align scale indicator to zero.
Fig. 10
n Tighten all screws securely.
BLADE
ZERO STOP
SET SCREW
GUARD
TO INSTALL DUST BAG
See Figure 12.
SMALL
COMBINATION
SQUARE
This tool comes with a dust bag for dustless cutting. To
install the dust bag:
n Position the nozzle of the dust bag in line with the dust
exhaust port on the back of the band saw.
n Push the dust bag nozzle firmly into the exhaust port.
NOTE: For more efficient operation, empty dust bag when
no more than half full. Turn bag inside-out and shake
vigorously to remove dust. This will permit better air flow
through the bag.
SAW
BLADE
Fig. 11
DUST
EXHAUST
PORT
DUST
BAG
Fig. 12
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO ADJUST BLADE TENSION
TO DECREASE
TENSION
TO INCREASE
TENSION
See Figures 13 - 14.
n Unplug the saw and remove the switch key.
n Make sure RapidSet™ Blade Tension Lever is in the
locked position. See Figure 14.
n Before using the band saw, turn the blade tension knob
on the top of the saw clockwise to engage tension.
Check blade tension by the sound the blade makes (similar
to plucking a guitar string).
n Pluck the back straight edge on the coasting side
opposite the blade guides while turning the tension knob.
Sound should be a musical note. Sound becomes higher
pitched as tension increases.
BLADE TENSION KNOB
Fig. 13
n Never increase blade tension so tight as to completely
compress the spring. When completely compressed, the
spring can no longer act as a shock absorber.
BLADE
TENSION
KNOB
NOTE: Too much tension may cause the blade to break.
Too little tension may cause the blade to slip on the wheels
or not track properly. The wider the blade, the more tension
must be used.
SPRING
TO LOCK BLADE
TENSION
TO TRACK THE BLADE
See Figure 14.
NOTE: Adjust blade tension properly before making tracking
adjustments. Check that the blade guides are not interfering
with the blade.
To Adjust:
TO UNLOCK BLADE
TENSION
n Open the front cover by releasing the upper and lower
latches. Watch the blade’s position on the upper tire as
you slowly turn the upper wheel clockwise by hand. If the
blade moves away from the center of the tire, the tracking
must be adjusted.
RAPIDSET™
BLADE TENSION
LEVER
BLADE
TENSION
KNOB
If the blade has moved left or right of center:
TRACKING
VIEW
WINDOW
NOTE: It may be necessary to loosen the hex nut for a larger
range of adjustments. Be sure to retighten after adjusting.
RAPID SET™
BLADE TENSION
LEVER
n Loosen hex nut. Turn the tracking knob (clockwise if blade
has moved left and counterclockwise if blade has moved
right) while turning the wheel by hand until the blade
moves back and rides in the center of the tire. Retighten
hex nut.
BLADE ON
WHEEL
HEX NUT
n Check the position of the blade on the lower tire. The
blade should be completely on the tire. If not, adjust the
tracking until the blade is on both tires.
n Rotate the upper wheel by hand in a clockwise direction
for a few more turns. Make sure the blade stays in the
same location on the tires. Readjust, if necessary, until
blade is tracking properly.
TRACKING
KNOB
n Close front cover and relatch.
Fig. 14
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
n Avoid awkward operations and hand positions where a
WARNING:
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
sudden slip could cause serious injury from contact with
the blade. Never place hands in blade path.
n Use extra supports (tables, saw horses, blocks, etc.)
when cutting large, small or awkward workpieces.
n Never use a person as a substitute for a table extension
or as additional support for a workpiece that is longer or
wider than the basic saw table.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
n When cutting irregularly shaped workpieces, plan your
work so it will not pinch the blade. For example, a piece
of molding must lay flat on the saw table. Workpieces
must not twist, rock or slip while being cut.
When backing up the workpiece, the blade may bind in
the kerf (cut). This is usually caused by sawdust clogging
the kerf or when the blade comes out of the guides. If this
happens:
WARNING:
To avoid blade contact, adjust the blade guide assembly
to just clear the workpiece. Failure to do so could result
in serious personal injury.
n Wait until the saw has come to a full and complete
stop.
APPLICATIONS
n Place the switch in the OFF ( O ) position then remove
the switch key from the switch assembly. Store key in a
safe place.
You may use this tool for the purposes listed below:
nScroll cutting and circle cutting of wood and wood com-
position products
n Unplug the saw from the power source.
nRelief cutting of wood and wood composition products
n Wedge the kerf open with a flat screwdriver or wooden
BASIC OPERATION OF THE BAND SAW
A band saw is basically a “curve cutting” machine that can
also be used for straight-line cutting operations like cross
cutting, ripping, mitering, beveling, compound cutting, and
resawing. It is not capable of making inside or non-through
cuts.
wedge.
n Open front cover and turn the upper wheel by hand while
backing up the workpiece.
RELIEF CUTS
Relief cuts are made when an intricate curve (too small
a radius for the blade) is to be cut. Cut through a scrap
section of the workpiece to curve in pattern line then carefully
back the blade out. Several relief cuts should be made for
intricate curves before following the pattern line as sections
are cutoff of curve “relieving” blade pressure.
This band saw is designed to cut wood and wood composi-
tion products only.
Before starting a cut, watch the saw run. If you experience
excessive vibration or unusual noise, stop immediately. Turn
the saw off, remove the switch key, and unplug the saw. Do
not restart until locating and correcting the problem.
SCROLL CUTTING
For general type scroll cutting, follow the pattern lines by
pushing and turning the workpiece at the same time. Do not
try to turn the workpiece while engaged in the blade without
pushing it – the workpiece could bind or twist the blade.
CUTTING PROCEDURES
n Hold the workpiece firmly against the saw table.
n Use gentle pressure and both hands when feeding the
work into the blade. Do not force the work; allow the
blade to cut.
REMOVING JAMMED MATERIAL
Never remove jammed cutoff pieces until the blade has come
to a full and complete stop.
n The smallest diameter circle that can be cut is determined
by blade width. A 1/4 in. (6 mm) wide blade will cut a
minimum radius of 3/4 in. (19 mm); a 1/8 in. (3 mm) wide
blade will cut a minimum radius of 1/4 in. (6 mm).
n Place the switch in the OFF ( O ) position, remove the
switch key from the switch assembly.
n Keep your hands away from the blade. Do not hand
hold pieces so small your fingers will go under the blade
guard.
n Unplug the saw from the power source before removing
jammed material.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TILTING THE TABLE
AVOIDING INJURY
See Figure 16.
n Make sure saw is level and does not rock. Saw should
always be on a firm, level surface with plenty of room for
handling and properly supporting the workpiece.
n Loosen the bevel lock handle slightly.
n Turn the bevel adjustment knob, tilting the saw table
toward the front of the saw housing until it reaches the
desired angle.
n Bolt saw to the support surface to prevent slipping,
walking or sliding during operations like cutting long,
heavy boards.
n Using the scale indicator, check angle markings.
n Turn saw off, remove switch key, and unplug cord from
n Retighten the bevel lock knob to hold saw table securely
the power source before moving the saw.
in place.
n Do not remove jammed cutoff pieces until blade has come
to a full and complete stop.
ON
OFF
n Choose the right size and style blade for the material and
type of cut you plan to do.
n Make sure that the blade teeth point down toward the saw
table, that the blade guides, thrust bearings, and blade
tension are properly adjusted, that the blade guide knob
is tight, and that no parts have excessive play.
n To avoid accidental blade contact, minimize blade
breakage, and provide maximum blade support, always
adjust the blade guide assembly to just clear the
workpiece.
SWITCH
KEY
n Use only recommended accessories.
n With the exception of the workpiece and related support
devices, clear everything off the saw table before turning
the saw on.
Fig. 15
n Properly support round materials such as dowel rods or
tubing because they have a tendency to roll during a cut
causing the blade to “bite”. To avoid this, always use a
“V” block or clamp workpiece to a miter gauge.
n Before removing loose pieces from the saw table, turn
BEVEL LOCK
KNOB
saw off and wait for all moving parts to stop.
LOCKING THE SWITCH
See Figure 15.
BEVEL ADJUST-
MENT KNOB
n Place the switch in the OFF (O) position. Wait until the
SCALE
INDICATOR
saw has come to a full and complete stop.
n Remove the switch key from the switch assembly. Store
key in safe place.
BEFORE LEAVING THE SAW
n Place the switch in the OFF (O) position. Wait until the
saw has come to a full and complete stop.
n Remove the switch key from the switch assembly. Store
SAW
TABLE
key in safe place.
n Unplug the saw from the power source.
n Make workshop childproof.
n Lock the shop.
Fig. 16
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO EXTEND THE SAW TABLE
See Figure 17.
The saw table can be extended to increase the work surface.
To lengthen the saw table:
LOCK
KNOB
n Loosen the table lock knob underneath the saw table by
turning counterclockwise.
n Using the extension scale on the saw table, extend the
MITER
GAUGE
SLOT
saw table to the desired position.
n Lock the saw table in place by turning the table lock knob
clockwise.
USING THE MITER GAUGE
See Figures 18 - 19.
The miter gauge can be turned 60° to the right or left.
n Loosen the lock knob on the miter gauge.
MITER
GAUGE
n With the miter gauge in the miter gauge slot, rotate the
gauge until the desired angle is reached on the index
scale.
n Retighten the lock knob.
Fig. 18
NOTE: For convenience, store the miter gauge in the slot
on the back of the band saw.
MITER
GAUGE
EXTENSION
SCALE
SLOT
Fig. 19
SAW
TABLE
TABLE
LOCK
KNOB
Fig. 17
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
USING THE RIP FENCE
See Figure 20.
n Unplug the saw.
RIP FENCE
n From either side of the saw blade, slide the rip fence onto
the saw table. Check for a smooth, gliding action.
n Push the locking handle down to automatically align and
secure the fence.
NOTE: Rip fence may be used on either side of the saw
blade.
NOTE: For wider rip cuts, lock the rip fence at 10 in. then
unlock the table lock knob. Using the side of the saw table
as an indicator, extend the extension table to the desired
position. Retighten the table lock knob.
Fig. 20
ADJUSTMENTS
WARNING:
BLADE
PHILLIPS
SCREWS
GUARD
Before performing any adjustment, make sure the tool
is unplugged from the power supply and the switch is in
the OFF ( O ) position. Failure to heed this warning could
result in serious personal injury.
SAW
TABLE
TABLE
ALIGNING
BOLT
INSTALLING AND ADJUSTING THE BLADE
See Figures 21 - 22.
WASHER
WARNING:
Failure to turn the saw off, remove the switch key, and
unplug the saw could result in accidental starting causing
possible serious personal injury.
WING
NUT
WARNING:
Always wear safety goggles or safety glasses with side
shields to protect your eyes while uncoiling band saw
blades. Failure to heed this warning could result in a
serious eye injury.
Fig. 21
n Turn the blade guide lock knob counterclockwise to
unlock the blade guide assembly. Turning the blade
guide knob (clockwise raises the blade guide assembly;
counterclockwise lowers it), position the blade guide
assembly about halfway between the saw table and
saw housing. Retighten the lock knob.
n Unplug the saw.
n Loosen and remove the wing nut, washer, and table
aligning bolt from the saw table.
n Open the front cover by releasing the upper and lower
n Turn the blade tension knob counterclockwise two full
turns to release some of the blade tension. Release blade
tension by pushing the RapidSet™ blade tension lever
to the left.
latches.
n Loosen the two screws that hold the blade guard in place
then remove the blade guard.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
n Carefully remove the old blade.
RAPIDSET™ BLADE
TENSION LEVER
n Wearing gloves, carefully uncoil the blade at arms length.
If the new blade was oiled to prevent rusting, it may need
to be wiped to keep the oil from your workpiece. Carefully
wipe in the same direction the teeth are pointing so the
rag does not catch on the teeth of the saw blade.
NOTE: The blade may need to be turned inside out if the
teeth are pointing in the wrong direction. Hold the blade
with both hands and rotate it inward.
LOWER
BLADE
GUIDES
NOTE: It may be necessary to release more tension with
the blade tension knob for the new blade to fit.
n Thread the blade through the saw table.
BLADE TENSION
KNOB
n With the teeth of the blade toward the front of the saw
and facing downward, place the blade through the lower
blade guides and around the lower wheel.
UPPER
WHEEL
n Slowly turn the upper wheel to the right or clockwise by
hand to center the blade on the rubber tires.
n Reengage the RapidSet™ blade tension lever then adjust
the blade tension. Check blade tracking and adjust if
needed.
BLADE
GUIDE
ASSEMBLY
n Adjust both upper and lower blade guides and thrust
SAW
BLADE
bearings.
n Reattach the aligning bolt, washer, and wing nut. Tighten
securely.
n Reattach the blade guard.
n Close front cover.
ADJUSTING BLADE GUIDE ASSEMBLY
See Figures 23 - 24.
LOWER
WHEEL
WARNING:
The blade guides have been preset at the factory.
These settings are functional for some applications. We
recommend that you check and adjust blade guide
settings before first use of your saw. Refer to “Adjusting
thrust bearings, blade guide support, and blade guides”
procedures explained in the adjustments section of this
operator’s manual.
Fig. 22
BLADE GUIDE
KNOB
BLADE GUIDE
LOCK KNOB
To prevent the blade from twisting or breaking, the blade
guide assembly should always be set approximately 1/8 in.
(3 mm) above the workpiece.
BLADE GUIDE
ASSEMBLY
n Turn the blade guide lock knob counterclockwise to
unlock the blade guide assembly.
n As a guide, use a scrap piece of the same wood you are
about to cut to set the height of the blade guide assembly.
Adjust the blade guide assembly by turning the blade
guide knob.
n Lock blade guide assembly in place by turning the blade
guide lock knob clockwise.
n Always lock the blade guide assembly in place before
turning on the band saw.
Fig. 23
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WARNING:
To avoid personal injury, maintain proper adjustment of
blade tension, blade guides, and thrust bearings.
n To check tension, raise the blade guide assembly all the
way up to expose the blade.
LOCK
UNLOCK
n Push the blade to the side with moderate force; the blade
should flex approximately 1/8 in. (3 mm).
ADJUSTING THRUST BEARINGS, BLADE
GUIDE SUPPORT, AND BLADE GUIDES
See Figures 24 - 26.
The upper and lower blade guides and thrust bearings
support the band saw blade during cutting operations. The
adjustment of the guides and bearings should be checked
whenever a different blade is installed.
WARNING:
Failure to turn the saw off, remove the switch key, and
unplug the saw could result in accidental starting causing
possible serious personal injury.
To Adjust Thrust Bearings:
The thrust bearings support the back edge of the blade
during cutting. The blade should not contact the thrust
bearings when you stop cutting. It is important that both
upper and lower thrust bearings be adjusted equally and
that both upper and lower blade guides be made simulta-
neously.
Fig. 24
BLADE
GUIDE
ASSEMBLY
UPPER BLADE
Adjust blade tracking and tension appropriate to the size
blade being used. Wide blades will require more tension than
narrow ones. Excessive tension may cause breakage of very
narrow blades while too little tension may cause wide blades
to track improperly and give poor cutting control.
GUIDE SUPPORT
BLADE GUIDE
SUPPORT
SCREW
THRUST
BEARING
SCREW
NOTE: The thrust bearing screw is the set screw located
on the front of the blade guide support. It is the set screw
on the front of the saw housing below the saw table for the
lower bearing.
THRUST
BEARING
BLADE GUIDE
SHAFTS
SET SCREW
BLADE GUIDE
BEARING
n Remove the blade guard by loosening the two screws.
n Turn the blade guide lock knob counterclockwise to
unlock the blade guide assembly. Turning the blade guide
knob clockwise, raise the blade guide assembly as far
as it will go. Turn the blade guide lock knob clockwise
to retighten.
BLADE GUARD REMOVED
FOR CLARIFICATION ONLY
Fig. 25
they are just barely touching the sides of the blade and
positioned just far enough forward as to not interfere with
the blade's teeth.
n Loosen the thrust bearing and blade guide support
screws. Adjust the thrust bearing and blade guide support
in or out so that the thrust bearing is centered on the
blade and is approximately 1/64 in. (.4 mm) away from
the back edge of the blade. Retighten the screws.
NOTE: Do not allow blade guide bearings to contact
the blade's teeth when the blade is pushed against the
thrust bearing. Contact with teeth will damage the blade,
bearings, and cause noisy operation.
n Loosen the set screw and move the blade guide bearings
in and out. Rotating the blade guide shafts with a small
screwdriver, adjust the blade guide bearings so that
n Retighten all screws and replace the blade guard if no
additional adjustments are to be made.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
To Adjust Blade Guide Support:
n Remove the blade guard by removing the two phillips
THRUST
BEARING
SCREW
screws that secure it in place.
n Adjust the position of the blade guide assembly. Loosen
the bottom screw on the right side of the blade guide
assembly using the 3 mm hex key.
THRUST BEARING
BLADE
GUIDE
SUPPORT
SCREW
n Slide the upper blade guide support on the shaft until
the front edge of the blade guides are about 1/64 in. (0.4
mm) behind the gullet of the blade. Tighten the screw
securely. Repeat this procedure for the lower blade guide
support.
n Replace the blade guard if no additional adjustments are
to be made.
LOWER BLADE
GUIDE SUPPORT
To Adjust Blade Guides:
The blade guides help keep the blade from twisting and
binding. The blade will be ruined if the blade teeth hit the
blade guides while using the band saw. The set of teeth and
the sharpened edge of teeth will be damaged by hitting the
blade guides. Proper adjustment of the upper and lower
blade guides will prevent this from happening.
BLADE GUIDE
SHAFTS
Fig. 26
n Remove the blade guard by loosening the two phillips
MITER GAUGE
INDICATOR
screws.
SCREW
n Loosen the two blade guide support screws that lock the
upper blade guides. Rotate the blade guide shafts with
a screwdriver to move the bearings closer or away from
the blade. The blade guide shafts should just barely touch
the blade. Do not pinch the blade. Make sure one guide is
not further away from the blade than the other. Retighten
the two blade guide support screws securely.
n Replace the blade guard if no additional adjustments are
to be made.
KNOB
n Repeat this procedure on the lower blade guides located
under the saw table.
NOTE: The lower blade guide support screw is the top screw
located on the right of the saw housing under the table.
WARNING:
Never operate saw without blade guard secured in
place. To do so could result in possible serious personal
injury.
TO ADJUST MITER GAUGE INDICATOR
See Figure 27.
If the miter gauge indicator is not set at 0˚:
n Open the extension table to its full capacity.
n Loosen the miter gauge knob. Place the miter gauge
Fig. 27
upside down in the slot on the table.
n Push the miter gauge against the saw table and retighten
n Turn the miter gauge indicator to 0°.
the miter gauge knob.
n Retighten the screw.
n If adjustment is needed, loosen the screw on the miter
gauge indicator.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LUBRICATION
WARNING:
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
MOTOR/ELECTRICAL
n Frequently vacuum or blow out sawdust from the
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing dust.
If operation is dusty, also wear a dust mask.
motor.
WARNING:
If the power cord is worn, cut or damaged in any way,
have it replaced immediately by a qualified service tech-
nician. Failure to do so could result in serious personal
injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
To avoid fire or electrocution, reassemble electric parts
with only identical replacement parts. Reassemble ex-
actly as originally assembled.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
TIRES
Cleaning tires:
n Pitch and sawdust accumulates on tires and needs to be
removed with a fine wire brush or a piece of wood. Do
not use a sharp knife or any kind of solvent.
n Keep your band saw clean.
n Remove sawdust from the inside frequently.
n Do not allow pitch to accumulate on the saw table, blade
guides, or thrust bearings. Clean them with gum and pitch
remover.
Replacing tires:
n Open front cover and remove saw blade. See section on
Installing and Adjusting the Blade, page 20.
n Apply a thin coat of automobile type wax to the saw
n Pry the worn tire away from the wheel carefully.
n Stretch the new tire around the wheel.
table’s top so the wood slides easily while cutting.
n Replace the saw blade and close the front cover.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BRUSHES
See Figure 28.
WARNING:
To prevent accidental starting that could cause possible
serious personal injury, turn off the saw, remove the
switch key, and unplug the saw before working on the
band saw.
The brushes located inside the saw housing on the door
help protect the tire and wheel by brushing off saw dust.
As the brushes become worn, it will be necessary to adjust
or replace them.
BRUSH
n Slide the brushes off the tab that holds them in place.
n Slide the new brush on the tab.
BRUSH
DRIVE BELT
See Figure 29.
WARNING:
To prevent accidental starting that could cause pos-
sible serious personal injury, turn off the saw, remove
the switch key, and unplug the saw before working on
the band saw.
Fig. 28
Due to wear or breakage, the drive belt may need to be
replaced. The drive belt is located behind the lower wheel
of the band saw.
MOTOR PULLEY
CAP BOLT
n Remove the phillips head screws from the belt cover and
remove belt cover. Set it aside.
n Remove the cap bolts from the bottom of the motor
housing using a hex key wrench.
n Remove the top motor cap bolt while supporting the
BELT
COVER
motor.
n Pull the motor away from the band saw and slide the
worn drive belt off of the pulley and discard.
n Place new drive belt on motor pulley and slide drive belt
over pulley while mounting the motor.
n Insert top cap bolt through motor housing and thread into
band saw. Finger tighten.
PULLEY
n Insert the remaining cap bolts into the adjusting slots and
DRIVE BELT
thread into band saw.
SCREWS
n Rotate the motor counterclockwise to tension the new
drive belt and tighten the cap bolts.
Fig. 29
n Replace the belt cover and attach with two philips head
screws.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Motor will not run.
1. Problem with On-Off switch or
power cord.
1. Have worn parts replaced before
using band saw again.
2. Motor defective.
2. Do not attempt any repair. Have
tool repaired by a qualified
service technician.
Blade does not run in the approxi-
mate center of the upper wheel.
1. Not tracking properly.
1. Adjust tracking, See Adjustments
section, Tracking the Blade.
Blade slows down when cutting.
1. Cutting too small a radius.
1. Stop feeding and back up the
material slightly until the band
saw speeds up.
2. Dull blade.
2. Replace blade.
Blade breaking.
1. Too much blade tension.
1. Adjust tension. See Adjustments
section, Adjusting Blade Tension.
2. Kink in blade caused by cutting
too small radius or turning the
material too fast when cutting.
2. Use correct cutting technique.
See section, Operation.
3. Thrust bearings scarred or not
rotating.
3. Replace the thrust bearings.
Saw is noisy when running.
1. Too much blade tension.
1. Adjust tension. See Adjustments
section, Adjusting Blade Tension.
2. Blade guides and bearings
are in contact with the blade.
2. Adjust upper and lower blade
guides and bearings. See Adjust-
ments sections, Adjusting Thrust
Bearings, Blade Guide Support,
and Blade Guides.
Blade will not cut straight.
1. Blade guides and bearings not
properly adjusted.
1. Adjust upper and lower blade
guides and bearings. See Adjust-
ments sections, Adjusting Thrust
Bearings, Blade Guide Support,
and Blade Guides.
2. Worn or defective blade.
2. Replace blade.
Blade guides will not stay in position. 1. Blade guide screws have
loosened.
1. Tighten blade guide screws
securely.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
10 in. BAND SAW
BS1001SV
EXTENSION CORD CAUTION
**Ampere rating
(on tool data plate) 0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
When using a power tool at a considerable distance from a power
source, be sure to use an extension cord that has the capacity to
handle the current the tool will draw. An undersized cord will cause
a drop in line voltage, resulting in overheating and loss of power.
Use the chart to determine the minimum wire size required in an
extension cord. Only round jacketed cords should be used.
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100'
When working with a tool outdoors, use an extension cord that
is designed for outside use. This is indicated by the letters "WA"
on the cord's jacket.
CAUTION: Keep the extension cord clear of the working
area. Position the cord so that it will not get caught on workpiece,
tools, or other obstructions while you are working with a power
tool.
Before using any extension cord, inspect it for loose or exposed
wires and cut or worn insulation.
**Used on 12 gauge - 20 amp circuit.
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or ser-
vice, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
a complete list of Authorized Service Centers.
• MODEL NO.
The model and serial numbers of your tool will be found on a plate on the back of the
saw. Please record the serial number in the space provided below.
•
•
MODEL NUMBER
SERIAL NUMBER
BS1001SV
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson SC 29625
Post Office Box 1207, Anderson SC 29622-1207
Phone 1-800-525-2579
983000-269
8-04
Download from Www.Somanuals.com. All Manuals Search And Download.
|