OPERATOR'S MANUAL
LAMINATE TRIMMER
DOUBLE INSULATED
TR45
Your laminate trimmer has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
n
Avoid accidental starting. Be sure switch is off
WARNING:
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch on
invites accidents.
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
nRemove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
nDo not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
nKeep your work area clean and well lit. Cluttered
nUse safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
nDo not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
benches and dark areas invite accidents.
nDo not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
nDo not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
nKeep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
TOOL USE AND CARE
ELECTRICAL SAFETY
nUse clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
nDo not force tool. Use the correct tool for your appli-
cation. The correct tool will do the job better and safer
at the rate for which it is designed.
nDouble insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation
eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
nDo not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
nDisconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
nStore idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
nMaintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
nAvoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
nDon’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
nDo not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.
nCheck for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
n
When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
nUse only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
n Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control
and deterioration of the enclosure plastic.
PERSONAL SAFETY
nStay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
nDress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
nWhen servicing a tool, use only identical replacement
SERVICE
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
nTool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
nHold tool by insulated gripping surfaces when nCheck damaged parts. Before further use of the
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting
tool “live” and shock the operator.
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
nKnow your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
nMake sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 16 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
nAlways wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
nProtect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
nProtect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
nInspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
nInspect tool cords periodically and, if damaged, have
repaired at your nearest Authorized Service Center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
nSave these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
No Hands Symbol
Hot Surface
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
To reduce the risk of injury or damage, avoid contact with
any hot surface.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-
wire grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An un-
dersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a tool, use an extension cord
that is designed for outside use. This type of cord is desig-
nated with “WA” on the cord’s jacket.
The double insulated system is intended to protect the
user from shock resulting from a break in the tool’s in-
ternal insulation. Observe all normal safety precautions
to avoid electrical shock.
Before using any extension cord, inspect it for loose or ex-
posed wires and cut or worn insulation.
**Ampere rating (on tool faceplate)
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performedonlybyaqualifiedservicetechnician. Forservice,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
0-2.0
2.1-3.4
3.5-5.0
5.1-7.0
7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100'
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area. Po-
sition the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged re-
place immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Input . . . . . . . . . . . . . . . 120 V, 60 Hz, AC only, 4.5 Amps
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . .3 lbs. (1.36 kg)
Cord Length . . . . . . . . . . . . . . . . . . . . . . . . . . .10 ft. (3 m)
Maximum Cutter Diameter . . . . . . . . . . .1-1/8 in. (29 mm)
Collet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 in. (6 mm)
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . .25,000/min.
WRENCHES
ON-OFF SWITCH
MOTOR
HOUSING
DEPTH OF CUT
SCALE
BASE
DEPTH
ADJUSTMENT
LATCH
SUB-BASE
HANDLES
LAMINATE
SUB-BASE
COLLET NUT
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
�
WOODWORKING
SUB-BASE
�
Fig. 1
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
DEPTH OF CUT SCALE
The trimmer has an adjustable depth of cut scale.
KNOW YOUR LAMINATE TRIMMER
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
LAMINATE SUB-BASE
The sub-base gives the operator greater visibility of the
workpiece.
SWITCH
The ON/OFF switch is located on top of the motor hous-
WOODWORKING SUB-BASE
The woodworking sub-base is used to rout circular and
parallel grooves. It allows the operator to grasp the trimmer
with both hands
ing.
HEAVY DUTY MOTOR
The trimmer has a powerful 4.5 amp motor with sufficient
power to handle many trimming jobs. The motor also has
replaceable brushes for ease of servicing.
ASSEMBLY
UNPACKING
This product requires assembly.
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
WARNING:
n Do not discard the packing material until you have care-
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Laminate Trimmer with Laminate Sub-base
Woodworking Sub-base
Sub-base Handles (2)
Ball Bearing Flush Trim Bit
Carrying Case
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
Wrenches
Operator’s Manual
Warranty Registration Card
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALLING/REMOVING CUTTERS
CUTTER
See Figure 2.
WRENCH ON
COLLET NUT
nUnplug the trimmer.
WRENCH ON
SPINDLE FLATS
nPlace the trimmer upside down on a workbench to gain
easy access to the spindle and collet nut.
nPlace the small end of one of the wrenches provided on
the spindle flats. This will hold the spindle stationary.
nPlace the larger end of the other wrench provided onto
the collet nut. Rotate the wrench counterclockwise to
loosen the collet nut as shown in figure 2.
WARNING:
If you are changing a cutter immediately after use, be
careful not to touch the collet nut, cutter, or collet with
your hands or fingers. They will get burned because of
the heat buildup from cutting. Always use the wrench
provided.
Fig. 2
LAMINATE
TRIMMER
nIf installing the cutter for the first time, it can be installed
once the collet nut is loose. If changing cutters, the cutter
will easily slip from the collet after loosening the collet
nut.
NOTE: The tip of the cutter has a protective wax coating
that must be removed before first-time use. Simply peel
off the wax coating and be sure that all traces of wax are
removed before using the trimmer.
HANDLE(S)
nThe collet is machined to precision tolerances to fit cut-
ters with 1/4 in. (6.4 mm) diameter shanks.
nWith the trimmer still upside down on a workbench, insert
the shank of the cutter into the collet. The shank of the
cutter should be close to but not touching the bottom of
the collet. This allows for expansion when the cutter gets
hot. A clearance of 1/16 in. is adequate.
nTighten the collet nut securely by turning clockwise with
the wrench provided as shown in figure 2.
WARNING:
If the collet nut is not tightened securely, the cutter may
come out during use, causing serious personal injury.
WOODWORKING
SUB-BASE
TO ATTACH THE WOODWORKING SUB-BASE
AND HANDLES
See Figure 3.
nUnplug the trimmer.
nTurn the trimmer upside down to remove the four sub-
SUB-BASE
SCREW(S)
Fig. 3
base screws and laminate sub-base.
nAttach the woodworking sub-base using the same four
screws.
nTurn the trimmer upright and thread the handles provided
into the threaded holes in the woodworking sub-base.
n
Tighten the screws securely. Do not overtighten.
nTighten the handles securely. Check often to assure the
handles remain securely tightened.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
ON
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suf-
ficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes re-
sulting in possible serious injury.
WARNING:
OFF
Do not use any attachments or accessories not recom-
mended by the manufacturer of this tool. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
nSmooth, professional trimming of laminates
nCabinet making, trimming counter tops and finishing
work
nTrimming wood and plastics
Fig. 4
TURNING ON/OFF THE TRIMMER
See Figure 4.
To turn the trimmer ON (I), slide the switch on top of the
trimmer to the ON (I) position. Return the switch to the OFF
(O) position when finished.
HOW TO OPERATE THE TRIMMER
See Figure 5.
Before starting the trimmer, unplug it and make sure the cut-
ter is securely tightened in the collet and that the depth of
cut is properly set. Never start the trimmer while the cutter
is in contact with the workpiece.
After completing a cut, pull the cutter slightly away from the
cut surface. Turn the trimmer off and wait for the rotating
cutter to completely stop before removing the base from
the work surface.
When cutting, fit the base of the trimmer over the work
surface and firmly hold the body of the trimmer with your
hand. Make sure the trimmer is running at full speed before
contacting the workpiece.
Fig. 5
WARNING:
WARNING:
Never install a cutter larger than 1-1/8 in. in this trimmer.
The use of larger bits can result in loss of control and
possible serious personal injury.
Avoid hand positions that may expose fingers to cutter
through open areas of trimmer base. Fingers entering
the opening in the trimmer base can be seriously cut or
burned.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DIRECTION OF FEED AND THRUST
D I R E C T I O N
T R I M M E R F E E D
See Figures 6 and 7.
The trimmer motor and cutter revolve in a clockwise direc-
tion. This gives the tool a slight tendency to twist in your
hands in a counterclockwise direction, especially when the
motor starts.
Feed the trimmer into the workpiece from left to right. When
fed from left to right, the rotation of the cutter pulls the trim-
mer against the workpiece. If fed in the opposite direction,
the rotation forces of the spinning cutter will tend to throw
the trimmer away from the workpiece, causing kickback.
This could result in loss of control of the trimmer.
BIT
ROTATION
Because of the extremely high speed of cutter rotation dur-
ing a proper feeding operation, there is very little kickback
to contend with under normal conditions. However, should
the cutter strike a knot, hard grain, foreign object, etc. that
would affect the normal progress of the cutting action, there
will be a slight kickback. Kickback could be sufficient to
spoil the trueness of your cut if you are not prepared. Such
a kickback is always in the direction opposite the direction
of cutter rotation.
BIT
ROTATION
TRIMMER FEED
DIRECTION
GUIDE OUTSIDE
THRUST
Fig. 6
To guard against kickback, plan your set-up and direction
of feed so that you will always be thrusting the tool—to
hold it against whatever you are using to guide the cut—in
the same direction that the leading edge of the cutter is
moving. The thrust should be in a direction that keeps the
sharp edges of the cutter continuously biting straight into
new (uncut) wood.
ROTATION
FEED
GUIDE
GUIDE INSIDE
ROTATION
GUIDE
FEED
THRUST
Fig. 7
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
speed and is taking very small bites to produce tiny, cleanly-
PROPER RATE OF FEED
severed chips. If the trimmer is forced to move forward too
fast, the speed of the cutter becomes slower than normal in
relation to its forward movement. As a result, the cutter must
take bigger bites as it revolves. Bigger bites mean bigger
chips and a rougher finish. Bigger chips also require more
power, which could result in overloading the motor.
Professional trimming and edge shaping depend upon care-
ful set-up and selecting the proper rate of feed.
The proper rate of feed is dependent upon:
nthe hardness and moisture content of the workpiece
nthe depth of cut
nthe cutting diameter of the cutter.
Under extreme force-feeding conditions, the relative speed
of the cutter can become so slow—and the bites it has to
take so large—that chips will be partially knocked off rather
than fully cut off. This will result in splintering and gouging
of the workpiece.
When cutting shallow grooves in soft woods such as pine, a
faster rate of feed can be used. When making cuts in hard-
woods such as oak, a slower rate of feed will be required.
Several factors will help you select the proper rate of feed.
nChoose a rate that does not slow down the trimmer
motor.
nChoose the rate at which the cutter advances firmly and
surely to produce a continuous spiral of uniform chips or
a smooth trim edge on laminate.
nListen to the sound of the trimmer motor. A high-pitched
sound means you are feeding too slowly. A strained,
lower-pitched sound signals force-feeding.
nCheck the progress of each cut. Too-slow feeding can
cause the trimmer to take off in a wrong direction from
the intended line of cut. Force-feeding increases the strain
of holding the tool and results in loss of speed.
TOO SLOW
TOO FAST
nNotice the chips being produced as you cut. If the trim-
mer is fed too slowly, it will scorch or burn the wood. If
the trimmer is fed too fast, it will take large chips out of
the wood and leave gouge marks.
Always test a cut on a scrap piece of the workpiece wood
or laminate before you begin. Always grasp and hold the
trimmer firmly with both hands when trimming.
Fig. 8
Ifyouaremakingasmall-diameter,shallowgrooveinsoft,dry
wood, the proper feed rate may be determined by the speed
at which you can travel the trimmer along the guide line. If
the cutter is a large one, the cut is deep or the workpiece
is hard to cut, the proper feed may be a very slow one. A
cross-grain cut may require a slower pace than an identical
with-grain cut in the same workpiece.
TOO SLOW FEEDING
See Figure 8.
When the trimmer is advanced into the work too slowly, the
revolving cutter does not dig into new wood fast enough to
take a bite; instead, it scrapes away sawdust-like particles.
Scraping produces heat, which can glaze, burn, or mar the
cut, and can overheat the cutter. Dull cutters can also con-
tribute to scraping and burning.
There is no fixed rule. Proper rate of feed is learned through
practice and use.
It is more difficult to control a trimmer when the cutter is
scraping instead of cutting. With practically no load on the
motor, the cutter will be revolving near top RPM, and will have
a greater than normal tendency to bounce off the sides of
the cut, especially if the wood has a pronounced grain with
hard and soft areas. The cut that results may have rippled
sides instead of straight.
FORCE FEEDING
See Figure 8.
The trimmer is an extremely high-speed tool (25,000/min),
and will make clean, smooth cuts if allowed to run freely
without the overload of a forced feed. Three things that cause
force feeding are cutter size, depth of cut, and workpiece
characteristics. The larger the cutter or the deeper the cut,
the more slowly the trimmer should be moved forward. If the
wood is very hard, knotty, gummy or damp, the operation
must be slowed still more.
Clean, smooth laminate trimming and edge shaping can be
done only when the cutter is revolving at a relatively high
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DEPTH OF CUT
See Figure 9.
DEPTH
OF CUT
WIDTH
OF CUT
Depth of cut affects the rate of feed and the quality of a cut.
Using the proper depth of cut can lessen the possibility of
damage to the trimmer motor and cutter.
Adeepercutrequiresaslowerfeedthanashallowone. Mak-
ing a cut that is too deep will slow the feed so that the cutter
is scraping, rather than cutting, and is not recommended.
A too-deep cut can cause smaller cutters to be broken off.
Cuttersthatare1/16in.(1.6mm)indiameterareeasilybroken
off when subjected to too much side thrust. A larger cutter is
not as likely to break, but attempting a cut that is too deep
may result in a rough cut, and may make it difficult to guide
and control the cutter as desired.
1ST. PASS
1ST.
PASS
2ND. PASS
2ND.
PASS
It is recommended that you do not exceed 1/8 in. (3.2 mm)
depth of cut in a single pass, regardless of the cutter size or
the softness or condition of the workpiece. This will result
in a higher quality cut.
Fig. 9
To make deeper cuts, it is necessary to make as many suc-
cessive passes as required, lowering the cutter 1/8 in
(3.2 mm) for each new pass. To save time, perform all the
cutting necessary at one depth setting, then lower the cutter
for the next pass. This will assure uniform depth when the
final pass is completed.
WARNING:
If the desired depth of cut is greater than can be safely
cut in one pass, make cuts in two or more passes. Do
not remove more than 1/8 in. in a single pass. Excessive
depth of cut can result in loss of control and the possibility
of serious personal injury.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO SET DEPTH OF CUT
See Figure 10.
nUnplug the trimmer.
nOpen the depth adjustment latch as indicated by the ar-
row in figure 10.
INDICATOR
POINT(S)
nSlide the motor housing section of the trimmer upward
until the tip of the cutter reaches the work surface. The
depth of cut is zero at this point.
nAdjust the position of the trimmer to obtain the desired
depth of cut by moving the motor housing section up or
down, as shown by the up/down arrow in figure 10. The
distance the cutter moves can be read on the depth of
cut scale. Each mark on the scale indicates a 1/16 in. (1.6
mm) change in depth setting. Indicator points are located
on the base.
DEPTH OF
CUT SCALE
nCompletely close the depth adjustment latch.
DEPTH
ADJUSTMENT
LATCH
WARNING:
Avoid open area of trimmer base. Serious personal injury
will result from contact with a rotating cutter.
NOTE: When adjusting the base, note the groove that serves
as a stop to prevent the motor housing from sliding directly
off and separating from the base.
Fig. 10
REMOVING THE BASE
See Figure 11.
nUnplug the trimmer.
nOpen the depth adjustment latch.
nHolding the trimmer by the motor housing, slide the base
downward and over. Continue to slide the base downward
to remove it.
NOTE: Replace the base before using the trimmer. Do
not attempt to operate the trimmer without the base in-
stalled.
WARNING:
Always use the laminate sub-base for laminate trimming.
Always use the woodworking sub-base for trim routing
operations. Use of the trimmer without a sub-base or
using the incorrect base can result in serious personal
injury.
STOP
GROOVE
Fig. 11
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
USING THE WOODWORKING SUB-BASE
WITH HANDLES
ROUT CIRCULAR GROOVE CLOCKWISE
Thewoodworkingsub-basewithhandlesisconvenientwhen
routing 4 in. (101.6 mm), 5 in. (127 mm), or 6 in. (152.4 mm)
circular grooves. It can also be used when routing grooves
parallel to the edge of the workpiece.
The handles allow you to grasp and hold the trimmer with
two hands, similar to grasping and holding a router.
ROUTING GROOVES IN A CIRCLE
See Figure 12.
nThere are three holes marked R2", R2-1/2", and R3" on
the sub-base. Each number represents a radius and may
be used when cutting circular grooves that are 4 in. (101.6
mm), 5 in. (127 mm) or 6 in. (152.4 mm) in diameter.
nSelect the radius for the desired circle, place a finish-
ing nail through the hole and securely tack it into the
workpiece. This will create a pivot axis for that size ra-
dius.
FINISHING
NAIL
nRout a circular groove in a clockwise direction only. See
the arrow in figure 12.
WORKPIECE
Fig. 12
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ROUTING GROOVES PARALLEL TO AN EDGE
See Figure 13.
ROUT GROOVE FROM RIGHT TO LEFT
You can use the scale provided on the woodworking sub-
base to cut a straight parallel line up to 1 in. (25.4 mm) from
the edge of the workpiece.
nThe intersection of the horizontal and vertical lines at the
center of the woodworking sub-base indicates the cen-
ter of the cutter. This is also the center of groove being
cut.
nFor grooves more than 1 in. (25.4 mm) from the edge
of workpiece, align the center of desired groove on the
workpiece with the centerline on the woodworking sub-
base. Then measure from the centerline on the woodwork-
ing sub-base to the guiding portion of the straight guide.
Tighten the knob on the straight guide securely.
nUsing “C” clamps and a board to act as the straight edge,
place the cutter at the desired position on the workpiece
and make the cut from right to left as shown by the arrow
in figure 13.
NOTE: The board being used as a straight edge must
be 1/4 in. (6.4 mm) thick or less to prevent contact with
the trimmer base. It must also be at least as long as the
workpiece in order to be a guide.
nThe thrust is from the trimmer against the straight edge.
nDo not make a cut that is too heavy in one pass. If a deep
cut is required, make successive passes at increasing
depths with each new pass until you reach the desired
groove depth.
Fig. 13
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LUBRICATION
WARNING:
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
ADJUSTING TENSION ON THE DEPTH
ADJUSTMENT LATCH
Withuse,thedepthadjustmentlatchmayloosen.Periodically
check the latch and adjust it when necessary.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
nUnplug the trimmer
nOpen the depth adjustment latch.
nUsing a small adjusting wrench, tighten the hex nut by
GENERAL MAINTENANCE
turning it clockwise. Do not overtighten.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
nClose the latch and assure the latch is securely tightened
by checking the sub-base. It should not move.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Electrictoolsusedonfiberglassmaterial,wallboard,spackling
compounds, or plaster are subject to accelerated wear and
possible premature failure because the fiberglass chips and
grindings are highly abrasive to bearings, brushes, commu-
tators,etc.Consequently,wedonotrecommendedusingthis
toolforextendedworkonthesetypesofmaterials. However,
if you do work with any of these materials, it is extremely
important to clean the tool using compressed air.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
nReplace the brush assemblies.
BRUSH REPLACEMENT
See Figures 14 - 15.
nReconnect the red and black lead terminals to the brush
tubes.
nUnplug the trimmer.
nEnsure that the wires are placed securely in the lead traps
nRemove screws from the top cover of the trimmer.
nRemove the top cover.
to prevent loose wires.
nReplace the brush tube clamps and clamp screws.
nReplace the top cover.
nRemove the clamp screws.
nRemove the brush tube clamps.
nReplace the screws on the top cover of the trimmer.
nTighten all screws securely. Do not overtighten.
nDisconnect the red and black lead terminals from the
brush tubes.
LEADTRAP
LEADTRAP
SCREWS
TOP
COVER
CLAMP
SCREWS
BRUSH
ASSEMBLY
BLACK
LEAD
RED
LEAD
BRUSH TUBE
CLAMPS
RED
LEAD
BLACK
LEAD
LEAD
TERMINAL
BRUSH
ASSEMBLY
Fig. 14
BRUSH
TUBE
nRemove the brush assemblies.
nCheck for wear. Replace both brush assemblies when
either has less than 1/4 in. length of carbon remaining.
Do not replace one side without replacing the other.
BRUSH
Fig. 15
nMake sure the wire terminals are secured to the brush
tubes prior to reassembly.
nReassemble using new brush assemblies. Make sure the
curvature of the brush matches the curvature of the motor
and that the brush moves freely in the brush tube.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
LAMINATE TRIMMER
DOUBLE INSULATION
TR45
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
TR45
• MODEL NUMBER
• SERIAL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
Phone 1-800-525-2579
983000-429
6-04
Download from Www.Somanuals.com. All Manuals Search And Download.
|