OPERATOR'S MANUAL
CORDLESS DRILL-DRIVER
MODEL NO. HP1441M
8
4
2
THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER.
Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator’s manual before using your new cordless drill-driver.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless drill-driver properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock, and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal
injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
KNOW YOUR CORDLESS TOOL
READ ALL INSTRUCTIONS
Safe operation of this cordless tool requires that you read
and understand this Operator's Manual and all labels affixed
to the tool. Learn its applications and limitations as well as
the potential hazards related to a cordless tool. Keep this
manual readily available for future reference.
■ KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite injuries.
■ CONSIDER WORK AREA ENVIRONMENT. Keep
work area well lit. Do not use tool in presence of
flammable liquids or gases.
IMPORTANT
■ GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH
GROUNDED SURFACES. For example: Pipes,
radiators, ranges, refrigerator enclosures.
Servicing of a tool requires extreme care and knowledge of
the system and should be performed only by a authorized
service technician. For service we suggest you return the
tool to your nearest Ryobi Authorized Service Center for
repair. When servicing, use only identical Ryobi replacement
parts.
■ KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
WARNING:
■ STORE IDLE TOOLS. When not in use tools should
be stored in a dry and high or locked-up place - out
of the reach of children.
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save this operator's
manual and review it frequently for continuing safe
operation, and instructing others who may use this tool.
■ DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
■ USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example - A
circular saw should never be used for cutting tree
limbs or logs.
WARNING:
When using power tools, basic safety precautions should
always be followed to reduce the risk of fire, electric shock,
and personal injury, including the following precautions.
■ WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION (Continued)
whenworkingoutdoors.Wearprotectivehaircovering
tocontainlonghairandkeepitfrombeingdrawninto
nearby air vents.
PRECAUTIONS ON USING YOUR
CORDLESS TOOL
This product contains Nickel-Cadmium batteries which
must be disposed of properly.
■ ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
■ Be aware that this tool is always in an operating
condition, because it does not have to be plugged
into an electrical outlet.
■ PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
■ First, charge the battery.
■ PROTECT YOUR HEARING. Wear hearing
■ Be sure the battery is snapped in place.
■ When not in use, lock the switch.
protection during extended periods of operation.
■ SECURE WORK. Use clamps or a vise to hold work.
It's safer than using your hand and it frees both
hands to operate tool.
■ When operating at a high place, be aware of things
below you.
■ DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
■ Before drilling into walls, ceilings, or floors, make
sure that there is no concealed electrical wiring
inside.
■ MAINTAIN TOOLS WITH CARE. Keep tools sharp
atalltimes,andcleanforbestandsafestperformance.
Follow instructions for lubricating and changing
accessories.
WARNING:
Drilling into electrical wiring can cause drill bit
and chuck to become electrically live. Do not
touch the chuck or metal housing when drilling
into a wall; grasp only the insulated handle(s)
provided on the tool.
■ REMOVE ADJUSTING KEYS AND WRENCHES.
Formhabitofcheckingtoseethatkeysandadjusting
wrenches are removed from tool before turning it on.
■ AVOIDUNINTENTIONALSTARTING. Donotcarry
thetoolwithyourfingerontheswitch. Besureswitch
is off when installing battery pack.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER/CHARGING ASSEMBLY
■ STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
■ SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating instructions
forchargingthebatterywiththefollowingcomponents:
■ CHECK DAMAGED PARTS. Before further use of
thetool, aguardorotherpartthatisdamagedshould
be carefully checked to determine that it will operate
properlyandperformitsintendedfunction.Checkfor
alignment of moving parts, binding of moving parts,
breakageofparts,mounting,andanyotherconditions
that may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this operator's manual.
MODEL
BATTERY
CHARGER
1400656
HP1441M
1400655
1400671
■ Before using battery charger/charging assembly,
read all instructions and cautionary markings on (1)
battery charger, (2) battery, (3) charging assembly,
and (4) products using battery.
WARNING:
■ DO NOT USE TOOL IF SWITCH DOES NOT TURN
IT ON AND OFF. Have defective switches replaced
by a Ryobi Authorized Service Center.
To reduce risk of injury, charge only nickel-
cadmiumtyperechargeablebatteries.Othertypes
of batteries can burst causing personal injury and
damage.
■ DRUGS,ALCOHOL,MEDICATION.Donotoperate
tool while under the influence of drugs, alcohol, or
any medication.
■ Do not expose charger/charging assembly to rain or
■ INSPECT FOR and remove all nails from lumber
snow.
before drilling.
■ Use of an attachment not recommended or sold by
thebatterycharger/chargingassemblymanufacturer
may result in a risk of fire, electric shock, or injury to
persons.
■ DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION (Continued)
■ To reduce risk of damage to electric plug and cord,
pull by the plug rather than the cord when
disconnecting charger/charging assembly.
not attempt to use it on any other voltage.
■ Consecutive charging may cause overheating. If
you need to recharge batteries consecutively, wait
for about 15 minutes to allow charger/charging
assembly to cool.
■ Makesurecordislocatedsothatitwillnotbestepped
on, tripped over, or otherwise subjected to damage
or stress.
■ Do not insert foreign matter into the hole for the
■ An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
battery in charger assembly.
■ Do not charge by means of an engine generator or
DC power source.
■ Do not disassemble the battery.
a. Thatpinsonplugofextensioncordarethesame
number, size and shape as those of plug on
charger/charging assembly.
■ Do not store the tool and battery in locations where
the temperature may reach or exceed 104° F (40°
C), such as outside sheds or metal buildings in
summer.
b. That extension cord is properly wired and in
good electrical condition; and
■ Do not incinerate the battery, even if it is severely
damaged or completely worn out. The battery may
explode in fire.
c. That wire size is large enough for AC ampere
ratingofcharger/chargingassemblyasspecified
below:
■ Battery leakage may occur under conditions of
extreme usage or temperature. If liquid comes in
contact with skin, wash quickly with soap and water,
then with lemon juice or vinegar. If liquid gets in your
eyes, wash with water for at least 10 minutes and
seek medical attention immediately.
Cord Length (Feet) 25 ft. 50 ft. 100 ft.
Cord Size (AWG) 16
16
16
Note: AWG = American Wire Gage
■ Do not operate charger/charging assembly with
damaged cord or plug. Replace immediately.
■ Do not short-circuit the battery.
■ Do not operate charger/charging assembly if it has
received a sharp blow, been dropped, or otherwise
damaged in any way; take it to a Ryobi Authorized
Service Center.
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some
examples of these chemicals are:
■ Do not disassemble charger/charging assembly;
take it to a Ryobi Authorized Service Center when
service or repair is required. Incorrect reassembly
may result in a risk of electric shock or fire.
■ To reduce risk of electric shock, unplug charger/
charging assembly from outlet before attempting
any maintenance or cleaning. Turning off controls
will not reduce this risk.
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-
treated lumber.
PRECAUTIONS REGARDING THE USE OF
CHARGER/CHARGING ASSEMBLY AND
BATTERY
Yourriskfromtheseexposuresvaries, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
■ Do not charge battery when temperature is below
50° F (10° C) or above 95° F (35° C).
■ Never attempt to connect two charger/charging
assemblies together.
■ The charger/charging assembly is designed to
operate on standard household electrical power. Do
SAVE THESE INSTRUCTIONS
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS:
3/8 in. Keyless
Chuck
Motor
Switch
DC Motor 14.4V
Variable Speed
No Load Speed
Clutch
0-650 RPM
24 Positions
120V, 60 Hz, AC Only
1 Hour
Charger Input
Charge Rate
IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES
When using your drill-driver continuously, the batteries in
occur under normal circumstances. Refer to "Charging
Your Drill-Driver" for normal recharging of batteries. If the
charger/charging assembly does not charge your battery
pack under normal circumstances, return both the battery
pack and charger/charging assembly to your nearest Ryobi
Authorized Service Center for electrical check.
your battery pack become hot. You should let a hot battery
pack cool down for approximately 30 minutes before at-
tempting to recharge.
Note: This situation occurs when continuous use of your
drill-driver causes the batteries to become hot. It does not
DISPOSAL OF THE EXHAUSTED BATTERY
To preserve natural resources, please
recycle or dispose of properly.
BATTERY PACK PREPARATION FOR
RECYCLING
Y
C
C
L
E
R B R C
This product contains nickel-cadmium
battery. Must be disposed of properly. Local,
state, or federal laws may prohibit disposal
of Nickel-Cadmium batteries in ordinary
trash. Consult your local waste authority for
information regarding available recycling
and/or disposal options.
1
7
.
N i C d
8
83
0
WARNING:
0
8
.
.
8
2
2
Upon removal, cover the battery pack's terminals with
heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its
components. Also, never touch both terminals with metal
objects and/or body parts, as short circuit can result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
For more information on battery recycling
call 1-800-8BATTERY.
WARNING:
Do not attempt to disassemble the battery pack. Fire or
injury can result.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR DRILL-DRIVER
LEVEL
TORQUE
See Figures 1 and 2.
ADJUSTMENT
RING
Before attempting to use any tool, familiarize yourself with all
operating features and safety requirements.
8
BIT
4
STORAGE
AREA
WARNING:
2
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict severe injury.
DIRECTION
OF ROTATION
SELECTOR
SWITCH
TRIGGER
CHARGING YOUR DRILL-DRIVER
KEYLESS
CHUCK
The battery pack for this tool has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it prior to use.
MAG TRAY™
(SCREW HOLDER)
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by re-
charging) for them to fully charge.
BATTERY
PACK
Fig. 1
TO CHARGE
■ Charge battery pack only with the charger provided.
■ Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
GREEN LIGHT "ON"
INDICATES FULLY
CHARGED
BATTERY
CHARGER
■ Connect charger to power supply.
■ Place battery pack in charger. See Figure 3. Align raised
rib on battery pack with groove in charger.
■ Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
When properly connected, red light will turn on.
■ Normally, the yellow and green lights on the charger will
come on. This indicates charger is in control charge
mode and should switch to fast charge mode within 5
minutes. When charger is in fast charge mode the red
light will come on. If after a period of 15 minutes the
yellow and green lights remain on, remove the battery
pack, wait 1 minute and reinsert battery pack in charger.
If the yellow and green lights continue to remain on an
additional 15 minutes, the battery pack is damaged and
will not accept charge.
RED LIGHT "ON"
INDICATES FAST
CHARGING MODE
YELLOW AND GREEN LIGHTS "ON"
INDICATES CONTROL CHARGE OR
POSSIBLE FAULTY BATTERY
Fig. 2
BATTERY
CHARGER
■ When your battery pack becomes fully charged, the red
light will turn off and the green light will turn on.
■ After normal usage, 1 hour of charge time is required to
be fully charged. A minimum charge time of 1 to 1-1/2
hours is required to recharge a completely discharged
tool.
■ The battery pack will become slightly warm to the touch
while charging. This is normal and does not indicate a
problem.
BATTERY
PACK
Fig. 3
■ DO NOT place charger in an area of extreme heat or
cold. It will work best at normal room temperature.
LED FUNCTION OF CHARGER
LED WILL BE LIGHTED TO INDICATE STATUS OF CHARGER AND BATTERY PACK:
1. Red LED lighted = Fast Charging Mode
2. Green LED lighted = Fully Charged Battery Pack
3. Yellow and Green LED Lighted = Control Charge or Defective Battery Pack.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CENTER POSITION
(LOCK)
WARNING:
If any parts are missing, do not operate tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
REVERSE
DIRECTION OF
ROTATION
SELECTOR
8
6
4
SWITCH
See Figure 4.
2
Your drill starts and stops by depressing and releasing the
switch trigger. Release the switch trigger to turn drill OFF.
SWITCH
TRIGGER
FORWARD
VARIABLE SPEED
See Figure 4.
Fig. 4
Your drill has a variable speed feature in the switch. The
switch delivers higher speed and torque with increased
trigger pressure. Speed is controlled by the amount of
switch trigger depression.
SWITCH LOCK
See Figure 4.
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
whennotinuse.Tolocktheswitchtrigger,placethedirection
of rotation selector in the center position.
TO INSTALL BATTERY PACK
BATTERY
PORT
■ Place the direction of rotation selector in center position.
BATTERY
PACK
See Figure 4.
■ Place the battery pack in your drill. Align raised rib on
battery pack with groove in drill's battery port.
See Figure 5.
■ Make sure the latches on each side of your battery pack
snap in place and that battery pack is secured in drill
before beginning operation.
LATCHES
TO REMOVE BATTERY PACK
■ Place the direction of rotation selector in center position.
See Figure 4.
■ Locate latches on side of battery pack and depress both
sides to release battery pack from your drill.
See Figure 5.
DEPRESS LATCHES TO
RELEASE BATTERY PACK
■ Remove battery pack from your drill.
Fig. 5
CAUTION:
When placing battery pack in your drill, be sure raised
rib on battery pack aligns with groove in drill's battery
port and latches snap in place properly. Improper
assembly of battery pack can cause damage to internal
components.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
REVERSIBLE
See Figure 4.
CHUCK
BODY
This tool is reversible. The direction of rotation is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch for
drilling. The drilling direction is reversed when the selector is
to the right of the switch. When the selector is in center
position, the switch trigger is locked.
8
6
4
RELEASE
(UNLOCK)
2
GRIP
(TIGHTEN)
CAUTION:
To prevent gear damage, always allow chuck to come to
CHUCK
COLLAR
a complete stop before changing the direction of rotation.
Fig. 6
To stop, release switch trigger and allow the chuck to come
to a complete stop.
CHUCK BODY
DRILL BIT
WARNING:
8
Battery tools are always in operating condition. Therefore,
switch should always be locked when not in use or when
carrying at your side.
6
4
2
CHUCK JAWS
CHUCK COLLAR
KEYLESS CHUCK
See Figure 6.
A keyless chuck has been provided with your drill to allow for
easy installation and removal of bits. As the name implies,
you can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand. Rotate
the chuck body with your other hand. The arrows on the
chuck indicate which direction to rotate the chuck body in
order to GRIP (tighten) or RELEASE (unlock) the drill bit.
RIGHT
Fig. 7
8
6
4
WARNING:
2
Do not hold the chuck body with one hand and use the
power of the drill to tighten chuck jaws on drill bits. Chuck
body could slip in your hand or your hand could slip and
come in contact with rotating drill bit. This could cause
an accident resulting in serious personal injury.
WRONG
INSTALLING BITS
■ Place the direction of rotation selector in center position.
Fig. 8
This will lock the switch trigger in the off position.
■ Openorclosethechuckjawstoapointwheretheopening
is slightly larger than the bit size you intend to use. Also,
raise the front of your drill slightly to keep the bit from
falling out of the chuck jaws.
Note: Rotate the chuck body in the direction of the arrow
marked GRIP to tighten the chuck jaws. DO NOT use a
wrench to tighten or loosen the chuck jaws.
■ Insertyourdrillbitintothechuckthefulllengthofthejaws.
WARNING:
See Figure 7.
Do not insert drill bit into chuck jaws and tighten as shown
in figure 8. This could cause drill bit to be thrown from
drill resulting in possible serious personal injury or
damage to the chuck.
■ Tighten the chuck jaws on the drill bit. To tighten, grasp
and hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
REMOVING BITS
See Figure 7.
TO DECREASE
TORQUE
■ Place the direction of rotation selector in center position.
This will lock the switch trigger in the off position.
8
6
■ Loosen the chuck jaws from drill bit.
4
■ To loosen: grasp and hold the collar of the chuck with one
hand, while rotating chuck body with your other hand.
2
TORQUE
ADJUSTMENT
RING
Note: Rotate chuck body in the direction of the arrow
marked RELEASE to loosen chuck jaws. DO NOT use a
wrench to tighten or loosen the chuck jaws.
■ Remove drill bit from chuck jaws.
TO INCREASE
TORQUE
MAG TRAY™
See Figure 9.
For convenience, your drill has a Mag Tray™ to place small
parts when doing a variety of tasks.
MAG TRAY™
(SCREW HOLDER)
SCREWDRIVING
TORQUE ADJUSTMENT
(Driving power of your drill-driver)
Fig. 9
When using your drill-driver for various driving applications, it
becomesnecessarytoincreaseordecreasethetorqueinorder
to help prevent the possibility of damaging screw heads,
threads, workpiece, etc. In general, torque intensity should
correspondtothescrewdiameter.Ifthetorqueistoohighorthe
screws too small, the screws may be damaged or broken.
BIT
STORAGE
AREA
SCREWDRIVER BIT
Thetorqueisadjustedbyrotatingthetorqueadjustmentring.
See Figure 9. The torque is greater when the torque adjust-
ment ring is set on a higher setting. The torque is less when
the torque adjustment ring is set on a lower setting.
8
6
4
The proper setting depends on the type of material and the
size of screw you are using.
2
SCREWDRIVER BIT
TO ADJUST TORQUE
Fig. 10
■ Identify the twenty four torque indicator settings located
on the front of your drill. See Figure 9.
■ Rotate adjustment ring to the desired setting.
• 1 - 4
• 5 - 8
For driving small screws.
2
For driving screws into soft material.
22
• 9 - 12 For driving screws into soft and hard
materials.
2 0
• 13 - 16 For driving screws in hard wood.
• 17 - 20 For driving large screws.
0
2
8
1
• 21 -
For heavy drilling.
LEVEL
BIT STORAGE
See Figure 10.
When not in use, bits provided with your drill can be placed
in the storage area located on the top of your drill.
LEVEL DRILLING
See Figure 11.
A convenient feature provided with your drill is a level. It is
recessed in the motor housing on top of your drill. It can be
used to keep drill bit level during drilling operations.
Fig. 11
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating tool. Failure to do so could result
in objects being thrown into your eyes, resulting in
possible serious injury.
DRILLING
See Figure 12.
2 2
1 8
2 0
When drilling hard, smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
lower speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate your
drill at lower speed until the hole is started.
The material to be drilled should be secured in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
WARNING:
Fig. 12
Be prepared for binding or bit breakthrough. When these
situations occur, the drill has a tendency to grab and kick
opposite to the direction of rotation, and could cause loss
of control when breaking through material. If you are not
prepared, this loss of control can result in possible serious
injury.
WARNING:
Do not force tool. Forcing tool can result in jamming and
loss of balance or footing, which could result in personal
injury.
When drilling metals, use a light oil on the drill bit to keep it
from overheating. The oil will prolong the life of the bit and
increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release switch
trigger immediately. Remove the bit from the workpiece and
determine the reason for jamming.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CHUCK REMOVAL
See Figures 13, 14, and 15.
MALLET
KEYLESS
CHUCK
To remove the chuck:
■ Lock the switch trigger by placing the direction of rotation
CHUCK
JAWS
selector in center position.
■ Insert a 5/16 inch or larger hex key wrench into the chuck
8
of your drill and tighten the chuck jaws securely.
6
■ Tap the hex key wrench sharply with a mallet in a
clockwise direction. See Figure 13. This will loosen the
screw in the chuck for easy removal.
4
2
■ Open chuck jaws and remove hex key wrench. Remove
the chuck screw by turning it in a clockwise direction.
See Figure 14. Note: The screw has left hand threads.
■ Insert hex key wrench in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand. See Figure 15.
HEX KEY
WRENCH
TO RETIGHTEN A LOOSE CHUCK
Fig. 13
The chuck may become loose on spindle and develop a
wobble. Also, the chuck screw may become loose causing
the chuck jaws to bind and prevent them from closing. To
tighten, follow these steps:
■ Lock the switch trigger by placing the direction of rotation
selector in center position.
■ Insert hex key wrench into chuck and tighten chuck jaws
securely. Tap hex key wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the spindle.
■ Open the chuck jaws and remove hex key wrench.
■ Tighten the chuck screw. Note: The chuck screw has left
hand threads.
Fig. 14
8
6
4
2
Fig. 15
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
DO NOT ABUSE POWER TOOLS. Abusive practices can
damage the tool, as well as the workpiece.
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts can create a hazard or cause
product damage.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
a clean cloth to remove dirt, oil, grease, etc.
CAUTION:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that may
damage, weaken, or destroy plastics.
CAUTION:
Any repairs requiring disassembly should only be
performed by a Ryobi Authorized Service Center. For
the repair center nearest you, call 1-800-525-2579.
BATTERIES
Your drill is equipped with Nickel-Cadmium rechargeable
batteries. Length of service from each charging will depend
on the type of work you are doing.
■ Store and charge your batteries in a cool area.
Temperaturesabovenormalroomtemperaturewillshorten
battery life.
The batteries in this tool have been designed to provide
maximum trouble-free life. However, like all batteries, they
will eventually wear out. Do not disassemble the battery
pack and attempt to replace the batteries. Handling of
these batteries, especially when wearing rings and jewelry,
could result in a serious burn.
■ Never store batteries in a discharged condition. Wait for
battery to cool and charge immediately.
■ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your tool for long periods of time without using it,
recharge the batteries every month or two. This practice
will prolong battery life.
To obtain the longest possible battery life, we suggest the
following:
CAUTION:
Your drill-driver contains special high temperature
batteries to help prevent battery damage when left on
charge for extended periods of time. However, once the
batteries become fully charged, we recommend that you
unplug the charger/charging assembly from power supply
and remove it from battery pack.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
CORDLESS DRILL-DRIVER
MODEL NO. HP1441M
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all
pertinent facts when you call or visit. Please refer to the Service Center insert or call 1-800-
525-2579 in the United States or 1-800-265-6778 in Canada for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
• MODEL NUMBER HP1441M
• SERIAL NUMBER
RYOBI AMERICA CORP.
RYOBI CANADA INC.
Post Office Box 910
Cambridge, Ontario N1R 6K2
Phone 1-800-265-6778
1424 Pearman Dairy Road
Anderson, SC 29625
Post Office Box 1207
Anderson, SC 29622-1207
Phone 1-800-525-2579
972000-761
8-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|