OPERATOR’S MANUAL
BLOWER / VACUUM
RY08510
Your blower/vacuum has been engineered and manufactured to Ryobi’s high standard for dependability, ease of opera-
tion, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
n
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire and/or carbon monoxide poisoning which will cause
death or serious personal injury.
n
Never operate the unit without a spark arrestor screen;
this screen is located inside the muffler.
n
Product users on United States Forest Service land, and
in some states, must comply with fire prevention regu-
lations. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
the federal, state, or local authorities in your area.
n
Do not allow children or untrained individuals to use this
unit.
n
n
Never start or run the engine inside a closed area; breath-
ing exhaust fumes can kill.
n
n
Before storing, allow the engine to cool.
WeareyeprotectionwhichismarkedtocomplywithANSI
Z87.1 as well as hearing protection when operating this
equipment.
Use only Ryobi replacement parts and accessories. Fail-
ure to do so may cause poor performance or possible
injury.
n
n
Keep all bystanders, children, and pets at least 50 feet
(15 m) away.
n
n
Maintain the unit per maintenance instructions in this
operator’s manual.
Wear heavy long pants, boots, and gloves. Do not wear
loose-fitting clothing, short pants, jewelry of any kind, or
go barefoot.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
SERVICE
n
To reduce the risk of injury associated with objects being
drawn into rotating parts, do not wear loose clothing,
scarves, neck chains, and the like. Secure long hair so it
is above shoulder level to prevent entanglement in any
rotating parts.
nBefore cleaning, repairing, or inspecting, shut off the
engine and make certain all moving parts have stopped.
Disconnect the spark plug wire, and keep the wire away
from the plug to prevent starting.
n
nService on the blower / vacuum must be performed by
qualified repair personnel only. Service or maintenance
performed by unqualified personnel could result in injury
to the user or damage to the product.
Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
n
n
Do not operate in poor lighting.
Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
nUse only identical replacement parts when servicing the
blower / vacuum. Use of unauthorized parts may cre-
ate a risk of serious injury to the user, or damage to the
product.
n
n
Wear a face filter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
Check theworkareabeforeeach use. Removeall objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
n
Always hold the blower in your right hand. Refer to the
Operation Instructions later in this manual for additional
information.
REFUELING
nFuel is highly flammable. Take precautions when using
to reduce the chance of serious personal injury.
n
n
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
nStore fuel in a cool, well-ventilated area, safely away from
spark and/or flame-producing equipment.
To reduce the risk of injury associated with contacting
rotating parts, stop the engine before installing or
removing attachments. Do not operate without guard(s)
in place. Always disconnect the spark plug before
performing maintenance or accessing any movable
parts.
nStore fuel in containers specifically designed for this
purpose.
nOnly refuel outdoors and do not smoke while refueling.
nAdd fuel before starting the engine. Never remove the cap
of the fuel tank or add fuel while the engine is running or
when the engine is hot.
n
Do not point the blower nozzle in the direction of people
or pets.
n
n
n
n
Do not smoke while handling fuel.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or flames.
n
n
n
n
Never run the unit without the blower tubes installed.
Never place objects inside the blower tubes.
Use only as directed in this operator’s manual.
Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
Do not operate vacuum without vacuum bag installed;
flying debris could cause serious injury. Always close
vacuum bag completely before operating.
n
n
Tighten the fuel cap securely after refueling.
Wipe spilled fuel from the unit. Move 30 feet away from
refueling site before starting engine.
n
n
Rotating impeller blades can cause severe injury. Stop
the engine before opening the vacuum door or installing / n
changing tubes. Do not put hands or any other object into
the vacuum tubes while they are installed on the unit.
Never attempt to burn off spilled fuel under any circum-
stances.
n
To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
Neverruntheunitwithouttheproperequipmentattached.
When used as a blower, always install the blower tubes.
When used as a vacuum, always install the vacuum tubes
andvacuumbag.Makesurethevacuumbagiscompletely
zipped when the unit is running to avoid flying debris.
nIf fuel is spilled, do not attempt to start the engine but
move the machine away from the area of spillage and
avoid creating any source of ignition until fuel vapors
have dissipated.
n
Avoid situations that could catch the vacuum bag on
fire. Do not operate near an open flame. Do not vacuum
warmashfromfireplaces, barbequepits, brushpiles, etc.
Do not vacuum discarded cigars or cigarettes unless the
cinders are completely cool.
nReplace all fuel tank and container caps securely.
n
Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
n Whendrainingthefueltank,useanapprovedfuelstorage
container in a well-ventilated area.
n
n
Select bare ground, stop engine, and allow to cool before
refueling.
Savetheseinstructions. Refertothemfrequentlyanduse
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
EXPLANATION
Safety Alert Symbol
Precautions that involve your safety.
To reduce the risk of injury, user must read and under-
stand operator’s manual before using this product.
Read the Operator’s Manual
Eye and Hearing Protection
Always wear safety goggles or safety glasses with side
shields, or a full face shield when operating this
product.
Do not run unit while vacuum door is unsecured.
Risk of long hair being drawn into air inlet.
Vacuum Door
Long Hair
Risk of loose clothing being drawn into air intake.
Loose Clothing
Gasoline and Oil
Use unleaded gasoline intended for motor vehicle use with
an octane rating of 87 [(R + M)/2] or higher. This product
is powered by a 2-cycle engine and requires pre-mixing
gasoline and 2-cycle oil.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Weight .......................................................................................................................................................................10.4 lbs.
Engine displacement....................................................................................................................................................25.4cc
Air Velocity:
MPH............................................................................................................................................................................205
CFM ............................................................................................................................................................................420
VACUUM BAG
SHOULDER STRAP
LOWER VACUUM
TUBE
UPPER VACUUM
TUBE
CHOKE LEVER
VACUUM BAG
VACUUM TUBE
SCREW
UPPER HANDLE
STARTER GRIP
AIR CLEANER
KNOB
PRIMER BULB
VACUUM HANDLE
Fig. 1a
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
HIGH VELOCITY NOZZLE WITH
WET LEAF SCRAPER
THROTTLE TRIGGER
ENGINE SWITCH
CRUISE CONTROL
(THROTTLE LOCK)
UPPER HANDLE
UPPER BLOWER TUBE
SWEEPER NOZZLE
DOOR TAB
INLET COVER
DOOR
Fig. 1b
KNOW YOUR BLOWER / VACUUM
See Figures 1a - 1b.
HIGH VELOCITY NOZZLE WITH WET LEAF
SCRAPER
The high velocity nozzle is great for wet sticky leaves. It
allows you to scrape wet leaves or debris while operating
the blower.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
MOTOR
VACUUM
The blower has a powerful 25.4cc engine with sufficient
power to handle tough blowing and vacuuming jobs.
Converting the blower to a vacuum / mulcher can be done
without using tools.
THROTTLE TRIGGER
The blower can be operated at any speed between idle and
full throttle.
VACUUM HANDLE
This feature allows user to perform vacuuming duties safely
and comfortably.
CRUISE CONTROL / THROTTLE LOCK
The Cruise Control (throttle lock) feature allows the user
to operate the blower without holding the throttle trigger.
To slow the engine, simply push the Cruise Control lever
forward.
VACUUM BAG
The vacuum bag attaches to the blower easily by using the
vacuum bag adaptor.
VACUUM TUBES
The vacuum tubes can be installed on the blower without
using any tools.
BLOWER TUBE AND NOZZLE
The blower tubes can be assembled and installed on the
blower using no tools.
MULCHER
The blower is equipped with a steel mulching blade that
efficiently reduces leaves at a 12:1 ratio.
SWEEPER NOZZLE
The sweeper nozzle allows for more area to be covered
during blower operation.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
UNPACKING
This product requires assembly.
INSTALLING THE VACUUM HANDLE
See Figure 3.
n
n
n
Lay unit on side as shown.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Insert vac handle into the base of unit.
Secure vac handle in place using two knobs as shown.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
PACKING LIST
Blower
Upper Blower Tube
Sweeper Nozzle
High Velocity Nozzle
Vacuum Handle
UPPER BLOWER
TUBE
Vacuum Handle Knobs (2)
Upper and Lower Vacuum Tubes
Vacuum Tube Screws (2)
Vacuum Bag Assembly
Vacuum Bag Adaptor
NOZZLE
Fig. 2
VACUUM
HANDLE
KNOBS
2-Cycle Engine Oil
Operator’s Manual
NOTE: Read and remove all hang tags and store with your
operator’s manual.
VACUUM
HANDLE
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
WARNING:
Do not attempt to modify this tool or create accessories not
recommended for use with this tool. Any such alteration
or modification is misuse and could result in a hazardous
condition leading to possible serious personal injury.
Fig. 3
ADAPTOR
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
ASSEMBLING THE BLOWER TUBES
See Figure 2.
n
Align raised tabs on main housing to the slots on upper
tube; slide together and tighten securely by twisting.
Check tightness after initial run and retighten if needed.
VACUUM BAG
n
To remove the tubes, rotate the tubes to unlock them and
remove from the blower housing outlet.
Fig. 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
INSTALLING THE VACUUM BAG
ADAPTOR INSTALLED
IN VACUUM BAG
See Figures 4 - 5.
n
n
n
Remove the nozzle and upper blower tube from the
blower.
Unzip the vacuum bag and place the adaptor inside as
shown.
Align the raised slots on the bag adaptor with the raised
locking tabs on the blower housing outlet; push the bag
adaptor onto the housing. Twist to lock into place.
n
n
Rotate the vacuum bag until the shoulder strap is upright.
RAISED
SLOT
Make sure the vacuum bag is zipped and closed before
starting the unit.
RAISED
LOCKING
TAB
INSTALLING THE VACUUM TUBES
See Figures 6 - 7.
Fig. 5
WARNING:
Rotating impeller blades can cause severe injury. Always
top the engine before opening the vacuum door or in-
stalling / changing tubes. Do not put hands or any other
object into the vacuum tubes while they are installed on
the unit.
VACUUM INLET
DOOR
VACUUM BAG
ASSEMBLY
NOTE: This vacuum / blower is equipped with a vacuum
door interlock. If vacuum door is open and vacuum tubes
are not installed, engine will not start.
To install the vacuum tubes:
DOOR TAB
n
Secure the upper and lower vacuum tubes together by
aligning the raised locking tabs with the raised slots.
VACUUM
DOOR
HINGE
n
Tap tube assembly on ground until the screw holes in
lower tube are in the raised slot of the upper tube. Secure
with supplied screws.
Fig. 6
n
n
Depress door tab and open vacuum door.
INLET DOOR
VACUUM
OPENING
Align tabs on housing with tube assembly. Insert tube
assembly into vacuum opening. Twist clockwise and lock
the upper vacuum tube into the blower housing.
VACUUM TUBE
ASSEMBLY
To remove the vacuum tubes:
n
n
n
Twist to loosen the upper vacuum tube by turning coun-
terclockwise.
Remove the vacuum tube assembly from the blower
housing.
Close the inlet cover door securely.
UPPER
VACUUM TUBE
LOCKING TAB
LOCKING TAB
Fig. 7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
PREMIUM EXACT MIX™ (50:1)
GASOLINE
OIL
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
1 gallon (US)
1 Liter
2.6 oz.
20 cc (20 ml)
WARNING:
FILLING THE TANK
WARNING:
Always stop the engine before filling the fuel tank. Never
add fuel to a machine with a running or hot engine. Move
atleast30ft.fromtherefuelingareabeforestartingengine.
Do not smoke while filling the tank.
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
APPLICATIONS
You may use this tool for the purposes listed below:
nClear leaves and other debris from your lawn
n Cleanthesurfacearoundthefuelcaptopreventcontami-
nKeep decks and driveways free from leaves and pine
nation.
needles
n Loosen the fuel cap slowly, by turning it counter-
clockwise.
WARNING:
n Pour the fuel mixture carefully into the tank.
Gasoline is extremely flammable and explosive. A fire or
explosion from gasoline will burn you and others.
n Clean and inspect the fuel cap gasket before replacing
the fuel cap.
n Replace the fuel cap and tighten it by turning it clock-
MIXING THE FUEL
wise.
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle oil. The mixture should be
at a 50:1 ratio, using Premium Exact Mix™ 2-cycle engine
oil. If Premium Exact Mix™ 2-cycle engine oil is not avail-
able, use a high quality 2-cycle engine oil, mixed at a 50:1
ratio. See chart later in this section.
n Wipe spilled fuel from the product.
n Move at least 30 ft. away from refueling area before start-
ing the product.
NOTE: It is normal for smoke to be emitted from a new
engine during first use.
To mix the fuel:
WARNING:
Check for fuel leaks. If you find any leaks, correct the
problem before using the product.
n Use a clean container that is approved for use with gaso-
line.
n Mix the Premium Exact Mix™ 2-cycle engine oil with
unleaded gasoline in the container, according to the
instructions on the oil package.
NOTE: This engine is certified to operate on unleaded gaso-
line intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.
WARNING:
A leaking fuel cap is a fire hazard and must be replaced
immediately.
NOTE: Premium Exact Mix™ fuel mixture will stay fresh up
to 30 days. DO NOT mix quantities larger than can be used
in a 30 day period.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING AND STOPPING
ENGINE
SWITCH
See Figures 8 - 9.
THROTTLE
TRIGGER
To start an engine that is cold or has run dry:
nFill the fuel tank, if necessary. Always use the proper
oil/gasoline mixture. See “Mixing the Fuel” on page 11.
nDisengage the cruise control lever.
NOTE: Do not engage the throttle trigger during the
starting process.
CHOKE
LEVER
nSlowly push the primer bulb seven times.
nSet the choke lever to the START position.
NOTE: If restarting a warm engine, leave the choke lever
in the RUN position.
STARTER
CORD
nPull the starter cord until the engine runs.
nReturn the starter cord gently to the starter housing. Do
PRIMER BULB
not allow the rope to snap back.
Fig. 8
nAllow the engine to run for 15 seconds to warm up before
CHOKE
LEVER
using.
CHOKE
LEVER
nEngage the throttle trigger to operate.
To stop the blower/vac:
START
POSITION
n Release the throttle trigger.
RUN
POSITION
n Press and hold the engine switch to the “O” or STOP posi-
tion.
OPERATING THE BLOWER
See Figures 10 - 11.
n Start the blower. Refer to “Starting and Stopping” earlier
in this manual. Hold the blower with the upper handle in
your right hand.
n To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
Fig. 9
PROPER OPERATING POSITION
n Operate power equipment at reasonable hours only - not
early in the morning or late at night when people might
be disturbed. Comply with the times listed in local ordi-
nances.
n To reduce sound levels, limit the number of pieces of
equipment used at any one time.
WARNING:
Keep away from all hot surfaces of the blower. Failure to
do so could result in possible serious personal injury.
Fig. 10
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
n Operate blower at the lowest possible throttle speed to
do the job.
n Check your equipment before operation, especially the
SWEEPER NOZZLE
muffler, air intakes, and air filters.
n Use rakes and brooms to loosen debris before blowing.
n Industyconditions, slightlydampensurfaceswhenwater
is available.
n Conserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas
such as gutters, screens, patios, grills, porches, and
gardens.
HIGH VELOCITY
NOZZLE
n Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
n Use the full blower nozzle extension so the air stream can
work close to the ground.
n After using blowers or other equipment, CLEAN UP!
Dispose of debris in trash receptacles.
n Use the sweeper nozzle for the everyday blowing opera-
tion.Thisnozzleallowsformoreareatobecoveredduring
the blowing operation.
n The high velocity nozzle is specifically designed for wet
sticky leaves. It allows you to scrape wet leaves or debris
while operating the blower.
Fig. 11
THROTTLE TRIGGER
CRUISE CONTROL
(THROTTLE LOCK)
CRUISE CONTROL / THROTTLE LOCK
The Cruise Control (throttle lock) can be used to operate the
blower without holding the throttle trigger.
To engage the cruise control / throttle lock:
See Figure 12.
n Pull cruise control lever back towards user, and stop at
the desired throttle setting.
n To release the cruise control, push cruise control lever all
the way towards the front of unit.
Fig. 12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
n Remove the vacuum tubes and clear the debris from the
VACUUM OPERATION
blower fan housing. Remove the bag and clear the tube.
A small rod or stick may be required to clear the entire
tubelength.Ensurethatalldebrishasbeenclearedbefore
reassembling the vacuum tubes.
See Figure 13.
WARNING:
Never run the unit without the blower tubes installed or
the vacuum door securely closed. Failure to do so could
result in serious personal injury.
PROPER OPERATING POSITION
n Install the vacuum tubes, vacuum handle, and bag. Refer
toInstallingtheVacuumBag,InstallingtheVacuumTubes
and Installing the Vacuum Handle earlier in this manual.
n Start the blower. Refer to Starting and Stopping earlier
in this manual.
n Placethevacuumbagstrapoveryourrightshoulder.Hold
the upper handle in your left hand and the lower handle
in your right hand.
n Move the blower / vacuum from side to side along outer
edge of the debris. To avoid clogging, do not place the
vacuum tube directly into the debris pile.
n Hold the engine higher than the inlet end of the vacuum
tube.
n Always point vacuum tube downhill when working on a
hillside.
n To avoid injury to the operator or unit, do not pick up
rocks, broken glass, bottles, or other similar objects.
n If the vacuum tubes should clog, stop the engine and
disconnect the spark plug wire before cleaning out the
obstruction.
Fig. 13
MAINTENANCE
GENERAL MAINTENANCE
WARNING:
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
WARNING:
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
WARNING:
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at a Ryobi Authorized Service Center.
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
REPLACING AND CLEANING AIR FILTER
See Figure 14.
WARNING:
A wet or dirty air filter can affect the way the engine starts,
performs, and wears. The air filter should be checked and
cleaned after 8 hours of operation.
A leaking fuel cap is a fire hazard and must be replaced
immediately.
For best performance, the air filter should be replaced once
each year.
SPARK PLUG
This engine uses a Champion RCJ4 with 0.63 mm
(0.025 in.) electrode gap. Use an exact replacement spark
plug and replace annually.
To clean the air filter:
nLoosen the knob on the air filter cover.
nRemove the cover.
STORAGE (1 MONTH OR LONGER)
n Drain all fuel from the tank into a container approved for
nLift the edge of the air filter carefully and peel it out.
nWash the air filter with warm, soapy water.
nRinse and squeeze to dry.
gasoline. Run engine until it stops.
n Clean all foreign material from the blower. Store it in a
well-ventilatedplacethat isinaccessibletochildren.Keep
away from corrosive agents such as garden chemicals
and de-icing salts.
nReinstall the air filter.
NOTE: Make sure the filter is seated properly inside the
cover. Installing the filter incorrectly will allow dirt to enter
the engine, causing rapid engine wear.
n Abide by all Federal and local regulations for the safe
storage and handling of gasoline. Excess fuel should be
used up in other 2-cycle engine powered equipment.
nReinstall the cover.
nTighten knob to secure.
AIR FILTER
KNOB
SPARK ARRESTOR
The muffler is equipped with a spark arrestor screen inside
muffler body. After extended use the screen can become
dirty, and you may need to have the screen replaced by an
authorized servicing dealer.
WARNING:
To avoid a fire hazard, never run the blower without the
spark arrestor in place.
CLEANING THE EXHAUST PORT AND MUFFLER
AIR FILTER
COVER
Depending on the type of fuel used, the type and amount of
oil used, and/or your operating conditions, the exhaust port,
muffler, and/or spark arrestor screen may become blocked
with carbon deposits. If you notice a power loss with your
gas powered tool, you may need to remove these deposits
to restore performance. We highly recommend that only
qualified service technicians perform this service.
Fig. 14
VACUUM BAG
A dirty bag will reduce performance. To clean the bag, turn
it inside out and shake. Wash the bag in soapy water at
least once a year. If the bag has deteriorated from normal
use, to obtain a replacement bag, consult your replacemnt
parts list.
FUEL CAP
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine per-
formance. If performance improves when the fuel cap is
loosened, the check valve may be faulty or filter clogged.
Replace the fuel cap if required.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
The following recommended accessories are currently
available.
WARNING:
ACCESSORIES
Current attachments and accessories available
for use with this tool are listed. Do not use any
attachments or accessories not recommended by the
manufacturer of this tool. The use of attachments or
accessories not recommended can result in serious
personal injury.
Air Filter .........................................Power Care - AP04107
Spark Plug......................................... Champion - RCJ-6Y
Fuel Cap.............................................................. AP04108
2-Cycle Oil.......................... (2.6 FL. OZ - 76 ml) AR99G01
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORIZED SERVICING DEALER.
PROBLEM
Engine fails to start.
CAUSE
REMEDY
No fuel in tank.
Fill tank.
Spark plug shorted or fouled.
Replace spark plug.
Replace spark plug.
Spark plug is broken (cracked
porcelain or electrodes broken).
Ignition lead wire shorted, broken, or Replace lead wire or attach to spark
disconnected from spark plug.
plug.
Ignition inoperative.
Contact authorized service center.
Engine hard to start.
Water in gasoline or stale fuel mixture. Drain entire system and refill with fresh
fuel.
Too much oil in fuel mixture.
Engine is under or over choked.
Weak spark at spark plug.
Air filter clogged.
Drain and refill with correct mixture.
Adjust choke as necessary.
Contact authorized service center.
Clean or replace air filter.
Engine lacks power.
Engine overheats.
Insufficient oil in fuel mixture.
Mix fuel as described in starting
instructions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
LIMITED WARRANTY STATEMENT
In addition, this warranty does not cover:
Ryobi Technologies, Inc. warrants to the original retail
purchaser that this Ryobi Technologies, Inc. product is
free from defect in material and workmanship and agrees
torepairorreplace,atRyobiTechnologies,Inc.’sdiscretion,
any defective product free of charge within these time
periods from the date of purchase.
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting
Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts,Tines,FeltWashers,HitchPins,MulchingBlades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bag
and Straps, Guide Bars, Saw Chains
n Two years if the product is used for personal, family or
household use;
Ryobi Technologies, Inc. reserves the right to change or
improvethedesignofanyRyobiTechnologies,Inc.product
without assuming any obligation to modify any product
previously manufactured.
n 90 days, if used for any other purpose, such as
commercial or rental.
This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY
DAY WARRANTY PERIOD. RYOBI TECHNOLOGIES,
INC.’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR
OR REPLACEMENT OF DEFECTIVE PARTS AND
RYOBI TECHNOLOGIES, INC.DOES NOT ASSUME OR
AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. RYOBI TECHNOLOGIES, INC. ASSUMES NO
RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL,
OROTHERDAMAGESINCLUDING,BUTNOTLIMITEDTO,
EXPENSEOFRETURNINGTHERYOBITECHNOLOGIES,
INC. PRODUCT TO AN AUTHORIZED SERVICE DEALER
ANDEXPENSEOFDELIVERINGITBACKTOTHEOWNER,
MECHANIC’STRAVELTIME,TELEPHONEORTELEGRAM
CHARGES, RENTAL OF A LIKE PRODUCT DURING THE
TIME WARRANTY SERVICE IS BEING PERFORMED,
TRAVEL, LOSS OR DAMAGE TO PERSONAL PROPERLY,
LOSS OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
Any part of the Ryobi Technologies, Inc. product
manufactured or supplied by Ryobi Technologies, Inc. and
found in the reasonable judgment of Ryobi Technologies,
Inc. to be defective in material or workmanship will be
repaired or replaced by an authorized Ryobi Technologies,
Inc. service dealer without charge for parts and labor.
Theproduct,includinganydefectivepart,mustbereturned
to an authorized service dealer within the warranty period.
The expense of delivering the Ryobi Technologies, Inc.
product to the dealer for warranty work and the expense
ofreturningitbacktotheownerafterrepairorreplacement
will be paid by the owner. Ryobi Technologies, Inc.’s
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach
of warranty shall be cause for cancellation or rescission
of the contract of sale of any Ryobi Technologies, Inc.
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by an authorized Ryobi Technologies, Inc.
service dealer.
This warranty is limited to ninety (90) days from the date
of original retail purchase for any Ryobi Technologies, Inc.
product that is used for rental or commercial purposes, or
any other income-producing purpose.
This warranty does not cover any Ryobi Technologies,
Inc. product that has been subject to misuse, neglect,
negligence, or accident, or that has been operated in any
way contrary to the operating instructions as specified
in this operator’s manual. This warranty does not apply
to any damage to the Ryobi Technologies, Inc. product
that is the result of improper maintenance or to any
Ryobi Technologies, Inc. product that has been altered
or modified. The warranty does not extend to repairs
made necessary by normal wear or by the use of parts or
accessories which are either INCOMPATIBLE WITH THE
RYOBITECHNOLOGIES,INC.productoradverselyaffect
its operation, performance, or durability.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all Ryobi Technologies, Inc.
products manufactured by Ryobi Technologies, Inc. and
sold in the United States and Canada.
To locate your nearest service dealer, dial 1-800-860-4050.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.
RYOBI TECHNOLOGIES, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA EMISSION
CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Ryobi Technologies, Inc. are pleased
to explain the Emission Control System Warranty on your non-road or small off-road engine. In California, new small off-road engines
must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model
year non-road engines must be designed, built, and equipped, at the time of sale, to meet the U.S. EPA regulations for small non-road
engines. The non-road engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA
standards for the first two years of engine use from the date of sale to the ultimate purchaser. Ryobi Technologies, Inc. must warrant
the emission control system on your non-road or small off-road engine for the period of time listed above provided there has been no
abuse, neglect, or improper maintenance of your non-road or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic
converter. Also included may be hoses, belts and connectors, and other emission related assemblies.
Where a warrantable condition exists, Ryobi Technologies, Inc. will repair your non-road or small off-road engine at no cost to you,
including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:
The 1995 and later small off-road engines are warranted for two years in California. In other states, 1997 and later model year non-
road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or
replaced by Ryobi Technologies, Inc. free of charge.
OWNER’S WARRANTY RESPONSIBILITIES
(a) As the non-road or small off-road engine owner, you are responsible for the performance of required maintenance listed in your
operator’s manual. Ryobi Technologies, Inc. recommends that you retain all receipts covering maintenance on your non-road or
small off-road engine, but Ryobi Technologies, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability
may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
(b) As the non-road or small off-road engine owner, you should be aware, however, that Ryobi Technologies, Inc., may deny you
warranty coverage if your non-road or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or
unapproved modifications.
(c) You are responsible for presenting your non-road or small off-road engine to a Ryobi Technologies, Inc., service dealer as soon as
a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a Ryobi Technologies, Inc., Customer
Representative at 1-800-860-4050.
COVERAGE:
Ryobi Technologies, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your non-road or small off-road
engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Ryobi Technologies, Inc. also war-
rants to the initial purchaser and each subsequent purchaser that your non-road or small off-road engine is free from defects in mate-
rials and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and
later small off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires
manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date the non-road or small off-
road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by
Ryobi Technologies, Inc. at no cost to the owner.
Ryobi Technologies, Inc. shall remedy warranty defects at any authorized Ryobi Technologies, Inc. engine dealer or warranty sta-
tion. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work deter-
mines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty
maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty.
Ryobi Technologies, Inc. is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s
regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)
These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.
MAINTENANCE REQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by Ryobi Technologies, Inc. in the operator’s
manual.
LIMITATIONS
The Emission Control Systems Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed or
replacements not conforming to Ryobi Technologies, Inc. specifications that adversely affect performance and/or durability, and
alterations or modifications not recommended or approved in writing by Ryobi Technologies, Inc., and
(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled
replacement point.
The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which
the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts
Inspect Before
Each Use
Clean Every
5 Hours
Replace
Every 25 Hours
or Yearly
Clean Every
25 Hours
or Yearly
Replace Every
50 Hours
CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X
AIR FILTER ASSY
includes:
Filter ................................................................. X............................. X
SPARK SCREEN ..................................................................................................................X
CARBURETOR ASSY
includes:
Heat Dam
Gaskets
FUEL TANK ASSY
includes:
Fuel Lines........................ X
Fuel Cap.......................... X
Fuel Filter
IGNITION ASSY
includes:
Spark Plug........................................................................................ X
ALL EMISSIONS RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
CALL US FIRST
For any questions about operating or maintaining your product,
call the Ryobi® Help Line!
Your product has been fully tested prior to shipment to ensure
your complete satisfaction.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
BLOWER / VACUUM
RY08510
WARNING:
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
CALIFORNIA PROPOSITION 65
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide
all pertinent facts when you call or visit. Please call 1-800-860-4050 for your nearest Ryobi
complete list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
RY08510
• MODEL NUMBER
• SERIAL NUMBER
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-860-4050
983000-647
3-05
Download from Www.Somanuals.com. All Manuals Search And Download.
|