Russound Universal Remote UNO LRC1 User Guide

Interaction of learned keys and keymover:  
Press VID, DVD, TV, or  
UNO once to select a  
home entertainment-  
component to control.  
3. Press the battery cover back into  
place. The tab should click when the  
cover is locked.  
4. Aim the remote control at the the  
TV and slowly alternate between  
pressing PWR and TV. Stop when the  
TV turns off.  
NOTE: If a code digit is “0”, the LED  
will not blink.  
PROGRAMMING  
TROUBLESHOOTING  
TV/VCR COMBO CONTROL  
• If both a learned function and a key-  
moved function are placed on the  
same key, whichever was pro-  
PROBLEM: LED does not blink when you press a  
key.  
5. Repeat step 4 three more times for  
remaining digits. Use 2 for the sec-  
ond digit, 3 for the third digit, and 4  
for the fourth digit.  
Perform the following instructions to  
control a TV/VCR Combo:  
SOLUTION: Replace the batteries with two (2) new  
AA alkaline batteries.  
4. Test the unit by pressing PWR and  
any mode key (e.g., VID, DVD, etc.). If  
the batteries are inserted correctly,  
the LED will blink once.  
UNO-LRC1  
grammed last will take precedence.  
Use the keypad (0 ~ 9)  
to directly select chan-  
nels (for example, 09  
or 31).  
NOTE: In the search mode, the UNO-  
LRC1 will send IR codes from its  
library to the selected device, starting  
with the most popular code first.  
PROBLEM: LED blinks when you press a key, but  
home entertainment component does not respond.  
UNIVERSAL LEARNING & PRE-  
PROGRAMMED REMOTE CONTROL  
1. Turn on the TV/VCR Combo and  
insert a video cassette.  
• A learned function cannot be used as  
a source for keymover, keymover  
always uses the key’s original func-  
tion as the source.  
SOLUTION: Make sure the UNO-LRC1 is aimed at  
your home entertainment component and is not far-  
ther than 15 feet away.  
6. To check for the codes of your other  
components, repeat steps 1 through  
5, but substitute the appropriate key  
(i.e., VID, DVD, or TV) component you  
are checking.As before, write down  
each four-digit code.  
NOTE: When batteries need replacement,  
the UNO-LRC1 will blink twice with every  
key press. Simply replace them and the  
remote control will be restored to its full  
functionality, including favorite settings.  
NOTE: Please read steps 2-4 completely  
before proceeding. We recommend  
highlighting or writing down the code  
for the brand you wish to program  
before moving onto step 2.  
PROBLEM: UNO-LRC1 does not control home enter-  
tainment components or commands are not working  
properly.  
Press MUTE once to turn sound  
5. Press SETUP once to lock in the code.  
off or on.  
Limitations on Learning  
6. To search for the codes of your other  
components, repeat steps 1 through  
5, but substitute the appropriate key  
(i.e., VID, DVD, or TV).  
SOLUTION: Tr y all listed codes for the component  
brands being set up. Make sure they can be operated  
with an infrared remote control.  
Press ENTER once after entering  
channel numbers on some TV  
models.  
• There are certain device codes which  
are not learnable. These include  
multi-frequency codes (e.g.  
Te l e f u n ken), some high frequency  
codes, and other unusual formats.  
2. On the UNO-LRC1, press DVD Press  
and hold SETUP until the LED blinks  
twice, then release SETUP.  
PROBLEM: TV/VCR combo does not respond prop-  
erly.  
PROGRAMMING  
COMPONENT CONTROL  
The UNO-LRC1 can control up to eight  
different components. Perform the fol-  
lowing instructions for each component  
you want controlled:  
CHANGING VOLUME LOCK  
The UNO-LRC1 is set to control volume  
of a component through your TV while  
Use VOL + (or VOL -) to raise (or  
lower) the sound volume.  
SOLUTION: Use the VCR codes for your brand.  
Some combo units may require both a TV code and  
a VCR code for full operation.  
LEARNING CAPABILITY  
3. Use the Setup Codes For TV/VCR  
Combos (on the back side) to locate  
the brand name and then enter the  
first four-digit code for your compo-  
nent. If performed correctly, the LED  
will blink twice.  
• The learner will support IR codes  
with carrier frequency up to 135  
Khz.  
PROBLEM: No volume on a 2nd TV.  
To op t i mize success, the learning process  
should be conducted in an area where  
there is a low level of IR emission. High  
levels of “natural light” or energy effi-  
cient fluorescent lights could interfere  
with a learning event The source and  
target (learner) remotes should be no  
more than 1 to 2 inches apart during a  
learning event and the IR LEDs of the  
two units should be aligned with each  
other. The learning operation is initiated  
as follows:  
in the  
,
, or mode. In UNO  
Use CH + (or CH -) to select the  
next higher (or lower) channel.  
SOLUTION: Follow instructions in Changing  
Volume Lo ck .  
mode, you have control of your UNO  
keypad’s volume.  
PROBLEM: CH+ , CH , and LAST do not work for  
-
• The unit can learn only one code per  
key. It can’t be taught a sequence of  
several keystrokes on one key.  
your RCA TV.  
If your TV is not remote controllable, or  
if you want volume to be controlled by a  
different component, you can change the  
Vo lu m e L o c k s e t t i n g to control a volume  
through a non-associated mode (e.g.,  
through the cable in the TV mode).  
NOTE: For TV/VCR Combo control, see the  
next section.  
Press LAST once to recall the last  
channel and to page back one  
screen in the main menu.  
SOLUTION: Due to RCA design (1983-1987), only  
the original remote control will operate these func-  
tions.  
NOTE: If the LED did not blink twice, then  
repeat steps 2 through 3 and try entering  
the same code again.  
1. Turn on a component (e.g.,VCR)  
and, if applicable, insert media,  
(e.g., cassette or disc).  
• All keys with the exception of Modes,  
and SETUP can be learned on.  
PROBLEM: Changing channels does not work  
properly.  
Press SLEEP to activate your TV’s  
sleep timer. Or if none is avail-  
able, press SLEEP to activate the  
UNO-LRC1’s sleep timer for  
automatic shut-off of your TV.  
Each key press (up to four) add  
15 minutes to the sleep timer.  
SOLUTION: If original remote controlrequired  
pressing ENTER to change channels, press ENTER on  
the UNO-LRC1 after entering the channel number.  
4. Aim the UNO-LRC1 at the compo-  
nent and press PWR once. It should  
turn off. If it does not respond, repeat  
steps 2-3, trying each code for your  
brand until you find one that works.  
If it still does not work, try searching  
for the code (see Searching For Your  
Code).  
• During a learning event. The source  
remote and target should be no more  
than 1 to 2 inches apart.  
NOTE: Please read steps 2-4 completely  
before proceeding. We recommend  
highlighting or writing down the codes  
and device you wish to program before  
moving onto step 2.  
To change Volume Lock to another  
mode:  
PROBLEM: Tried “Search Method” and still could  
not find a working code.  
1. Press and hold SETUP until double  
blink confirmation. Press 9 - 7 - 5 to  
initiate learning mode.  
SOLUTION: Tr y the “Search Methodagain after  
clearing out the device key as follows: Press and hold  
SETUP until red light blinks twice, then release. Next  
enter 9 - 9 - 2. Then press and release the device key  
to be cleared twice.  
• In some cases you may be required  
to re-learn a code if it is not correctly  
learned.  
1. On the UNO-LRC1, press and hold  
SETUP until the LED blinks twice,  
then release SETUP.  
USER GUIDE  
Press INPUT once to  
switch the input of the  
chosen component.  
2. On the UNO-LRC1, press a compo-  
nent key once (i.e., VID, DVD or TV).  
Press and hold SETUP until the LED  
blinks twice, then release SETUP.  
2. Press [MODE] and key to be learned  
(time out if no key pressed in 10 sec-  
onds).  
• The learning process should con-  
ducted in an area where there is a  
low levels of IR emission. High levels  
of “nature light” or Energy efficient  
fluorescent lights, could interfere  
with a learning event.  
PROBLEM: Remote control does not turn on Sony  
or Sharp TV/VCR Combo.  
2. Enter 9 - 9 - 3 and then press any  
mode key once (except TV). The LED  
will blink twice.  
INTRODUCTION  
NOTE: If the device does not have a PWR  
key, press PLAY.  
SOLUTION: For power on, these prod-ucts require  
programming TV codes. For Sony, use TV code  
0000 and VCR code 0032. For Sharp, use TV code  
0093 and VCR code 0048.  
Use GUIDE to displaythe program  
The UNO-LRC1 from Russound is the  
complete solution for all of your remote  
control requirements. It is designed to  
operate source devices and the audio  
system keypad.  
3. Visible LED flashes rapidly (time out  
if no received signal detected in 4  
sec.)  
guide.  
5. If you’ve located a setup code that  
works, but it has a separate TV code,  
you’ll also need to program it into the  
UNO-LRC1 to access volume control  
as follows:  
Components are assigned  
to each component key.  
3. Now, whenever you press VOL +,  
VOL –, or MUTE, volume will be con-  
trolled by your mode choice.  
Use EXIT to exit out of the select-  
ed component’s menu or guide.  
=Cable, Satellite, DSS,Vid Acc.  
=VCR, DVD, LDP,Audio Cassette,  
DVR  
=VCR, DVD, LDP,Audio Cassette,  
DVR  
• In general, it is not recommended to  
learn a function to the Record Key.  
The Record Key requires a double  
key press to send the record function  
in normal operation. The double key  
press is lost when the Record key is  
involved in most learning operations.  
This lack of consistency in operation  
generates a source of confusion for  
the user and is best to be avoided  
when possible. However, the Record  
key is learnable.  
4. Hold teaching remote close to IR  
LED and press key to be taught.  
To change Volume Lock back to the  
TV mode:  
The UNO-LRC1 is also customizable to  
allow for key configurations that meet  
your specific needs. It’s also packed with  
these features for you to choose from:  
Use the cursor keys to  
move the cursor in the  
program guide and  
menu screens.  
a. Press TV once. The LED will  
5. Visible LED goes out. Continue to  
press teaching key until double blink  
from visible LED. (One long blink  
indicates a learning failure)  
blink twice.  
1. On the UNO-LRC1, press and hold  
SETUP until the LED blinks twice,  
then release SETUP.  
=UNO Keypad  
b. Enter the TV code for your  
TV/VCR Combo. If correct, the  
LED will blink twice.  
• Preprogrammed technology for  
easy setup  
3. Use the Manufacturer’s Codes (on the  
back side) to locate the the type of  
component and brand name and  
then enter the first four-digit code  
for your component. If performed  
correctly, the LED will blink twice.  
Use SELECT to choose options  
from your selected component’s  
menu or guide.  
6. Repeat steps 2 through 5 as often as  
desired (up to limit of memory).  
2. Enter 9 - 9 - 3 and then press TV.  
The LED will blink twice.  
If there is no separate TV code listed,  
you will need to perform the follow-  
ing steps to access volume control:  
• Controls UNO keypads and source  
equipment  
7. Exit learning mode by pressing  
3. Now, whenever you press VOL +,  
VOL –, or MUTE on the UNO-LRC1,  
volume will be controlled by your TV.  
Use INFO to display current  
channel and program informa-  
tion.  
SETUP, or by time out (10 seconds).  
• Inclusive audio/video library  
a. Press and hold SETUP until the  
LED blinks twice, then release  
SETUP.  
At step 5, one long blink indicates learning fail-  
ure, which could be:  
Typically, there are up to 24 buttons  
that can be learned.  
• Dedicated operation of audio system  
keypad  
NOTE: If the LED did not blink twice, then  
repeat steps 2 through 3 and try entering  
the same code again.  
Press MENU to access the menu  
of your chosen component.  
a. Bad capture (try again)  
b. Memory full (delete some other  
function)  
c. Unlearnable code  
Deleting a learned code:  
This manual provides a basic overview  
on how to set up and operate the UNO-  
LRC1. Please read the following instruc-  
tions to see how easy setup is.  
b. Enter 9 - 9 - 3 . The LED will  
4. Aim the UNO-LRC1 at the compo-  
nent and press PWR once. It should  
turn off. If it does not respond, repeat  
steps 2-3, trying each code for your  
brand until you find one that works.  
If it still does not work, try searching  
for the code (see Searching For Your  
Code).  
CHECKING THE CODES  
Use the transport keys  
to control your VCR, or  
CD or DVD player.  
blink twice.  
If you have set up the UNO-LRC1 using  
the Searching For Your Code procedure,  
you may need to find out which four-  
digit code is operating your equipment:  
c. Press DVD once. The LED will  
blink twice.  
Use these keys to con-  
trol the UNO-Series  
Keypads  
To de l e te a l e arned code, either overwrite  
it with a new code on the same key, or  
use the following sequence:  
FEATURES AND FUNCTIONS  
Use the Key Charts to learn how the  
UNO-LRC1 functions.  
SEARCHING FOR YOUR CODE  
For example, to find out which code is  
operating your TV:  
If your device does not respond to the  
UNO-LRC1 after trying all codes listed  
for your brand, or if your brand is not  
listed at all, try searching for your code.  
For example, to search for a code for  
your TV:  
Press [MODE] then SETUP (press and  
hold till you see two blinks) 9 - 7 - 6  
then press the key you wish to delete  
twice.  
NOTE: If the device does not have a PWR  
key, press PLAY.  
INSTALLING BATTERIES  
1. On the back of the UNO-LRC1, push  
the tab and lift off the battery cover.  
1. On the UNO-LRC1, press TV once.  
Key Charts  
2. Press and hold SETUP until the LED  
The LED (red light) blinks to  
show that the remote control is  
working and is sending signals.  
5. Repeat steps 1 through 4 for each  
component you want the UNO-LRC1  
to control.  
blinks twice, then release SETUP.  
Sending a key’s original (preprogrammed)  
function:  
3. Enter 9 - 9 - 0. The LED will  
2. Obtain two (2) fully-charged AA  
alkaline batteries. Match the + and –  
marks on the batteries to the + and  
– marks in the battery case, then  
insert the new batteries.  
blink twice.  
1. On the UNO-LRC1, press TV once.  
Use SETUP for all programming  
sequences.  
If a function is learned onto a key, then  
SETUP - key will send the key’s original  
function (as long as nothing else has  
been learned or keymoved onto the  
“shifted” key as well).  
4. To view the code for the first digit,  
press 1 once. Wait 3 seconds, count  
the LED blinks (e.g., 3 blinks = 3)  
and write down the number.  
2. Press and hold SETUP until the LED  
blinks twice, then release SETUP.  
Press PWR once to turn on or off  
the selected home entertainment  
component.  
3. Enter 9 - 9 - 1. The LED will  
blink twice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Quadra Fire Indoor Fireplace QVI 30FB S User Guide
RBH Sound Portable Speaker MC 6CT User Guide
ResMed Respiratory Product VPAP Auto User Guide
Ricoh All in One Printer MP C2500 User Guide
Rosewill Video Game Keyboard RK 8200 User Guide
Rotel Music Mixer RB993 User Guide
Salton Hot Beverage Maker RHOK3123 User Guide
Samson Music Mixer Mixpad 12 User Guide
Sanyo Tool Storage CVW EXA124 User Guide
Sennheiser Headphones 09969 User Guide