ST2S
SmartTuner
Installation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Product Introduction..........................................................................................................................4-5
Component Guide
ST2S Front Panel................................................................................................................................6
ST2S Rear Panel ................................................................................................................................7
ST2-RC Remote Control.......................................................................................................................8
ST2S Setup and Connections
Basic Connections ..............................................................................................................................9
ST2-KP and CAi Connections ............................................................................................................10
CAV6.6 Connections .........................................................................................................................11
Antenna Connections....................................................................................................................12-14
ST2S Operation
SIRIUS Radio Activation .....................................................................................................................15
SIRIUS Radio Displays .......................................................................................................................15
SIRIUS Radio Modes ........................................................................................................................16
Preset .....................................................................................................................................17
Category Search..................................................................................................................17-18
Now Playing.............................................................................................................................18
Display Preferences..................................................................................................................19
SIRIUS ID .................................................................................................................................19
Channel Lock ...........................................................................................................................20
Front Panel Controls..........................................................................................................................21
ST2-RC Remote Control.....................................................................................................................22
ST2-KP Keypad Controls ...................................................................................................................23
UNO-S2 Keypad Controls with CAV6.6...........................................................................................24-25
UNO-LRC1 Remote Control with CAV6.6 ........................................................................................26-27
ST2S Tuner Programming
ST2 Chassis Setup Menu ..................................................................................................................28
Source Number........................................................................................................................28
Update Firmware .................................................................................................................28-29
Factory Initialization ..................................................................................................................29
System Info..............................................................................................................................30
Tuner Setup Menu for SIRIUS.............................................................................................................30
Memory Name .........................................................................................................................30
Bank Name..............................................................................................................................30
Controller ID.............................................................................................................................32
Diagnostics..............................................................................................................................32
Factory Initialization .............................................................................................................32-33
System Info..............................................................................................................................33
Tuner Setup Menu for AM/FM ............................................................................................................34
Memory Name .........................................................................................................................34
Bank Name..............................................................................................................................34
Region ................................................................................................................................34-35
Backup and Restore .........................................................................................................................35
Programming for CAV6.6 Use............................................................................................................36
Technical Specifications ....................................................................................................................37
Warranty & Repair.............................................................................................................................38
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
DESCRIPTION
The ST2S Tuner can be controlled from the front
panel or by the dedicated ST2-KP tuner keypad.
It can also be controlled by the ST2-RC IR remote
aimed at the tuner’s front panel IR receiver. The
ST2-RC IR codes can be learned into any IR
learning remote control for easy system integra-
tion. It can also be controlled by IR signals
received through the IR connections on the rear
panel from IR repeating system commonly used
in distributed audio systems.
Thank you for choosing the Russound ST2S
Smart Tuner. Whether you are adding radio to an
existing system, expanding a CAi Series system
or taking advantage of the CAV6.6’s robust
RNET® communication link, the ST2S Tuner is
designed to meet your needs.
The ST2S Tuner is like having two radios in one.
The AM/FM tuner provides broadcast of local
AM/FM stations, and the SIRIUS tuner delivers all
the diversity and choices available to SIRIUS
radio subscribers. The two modules share one
set of controls and display on the front of the
unit, but each runs independently. This arrange-
If the ST2S Tuner is part of an RNET-enabled sys-
tem such as the CAV6.6-S2 system, the tuner
can be controlled through an RNET keypad such
as the UNO-S2.
ment allows two different broadcasts at the same The ST2 Tuner also has an RS-232 port to sup-
time in a multi-room audio distribution system.
port fully bi-directional integration into whole-
house control systems such as Crestron® and
AMX®.
SIRIUS brings you satellite radio
the way you want to hear it.
SIRIUS satellite radio provides
FEATURES
over 120 channels of unique programming, all
with digital quality sound. Enjoy 65 channels of
100% commercial-free music, with over 50 chan-
nels of sports, news and entertainment.
• SIRIUS satellite radio
• AM/FM Tuner
• Compact single rack unit chassis
• Six banks of six memory presets each per
tuner (72 total presets) for storing AM/FM
station settings or SIRIUS channels
• Custom names for presets and banks
• Two Favorite presets per tuner
• Stereo or mono mode
The wide variety of SIRIUS programming choices
offers something for everyone, but some adult
content may not be suitable for children. The
ST2S provides a parental lock out feature to eas-
ily block access to a specific SIRIUS channel.
• Local or distant mode
• Dedicated IR remote control
SIRIUS satellite radio is a subscription-based
service, and listeners can subscribe by visiting
SIRIUS at 888-539-7474.
• Individual IR direct inputs for each tuner
• Front panel IR receiver
• Supports two ST2-KP optional tuner keypads
• RNET connections send tuner frequency and
control information to UNO keypad display
• RS-232 control and programming. User
settings can be backed up and restored.
In addition to the traditional AM/FM broadcast
tuner function and the SIRIUS satellite access,
the ST2S Tuner can store up to 72 favorites, or
memory presets. These are stored in groups of
six called banks. There are six banks for each
tuner. Each preset and each bank can be given a
custom name of your choice.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
INSTALLATION APPLICATIONS
RNET-enabled System
these connections (one is supplied with each CAi
system). If you are using an IR-controlled system
from another manufacturer, installation should be
similar. The ST2S IR codes may be learned into
many other manufacturers’ remote controls that
have learning capability for unified control over
the A/V equipment.
When the ST2S Tuner is used with an RNET-
enabled device such as the CAV6.6 and is con-
nected to it through the Link In or Link Out port,
the tuner will be controlled by the CAV6.6
through the UNO-S2 keypad. Through RNET,
tuner information such as Tuner 1 or 2, station
frequency or channel, preset names and AM/FM
band or SIRIUS is displayed on UNO-S2 keypads.
An additional RNET device can be connected to
an existing ST2 by using the Link Out of the first
unit into the Link In of the second unit.
Note: Optional ST2-KP keypads can be used to
provide control for the ST2S Tuner and are
designed to be used with IR-controlled systems.
RS-232 Controlled System
The ST2S Tuner can be controlled using the
RNET protocol provided via the RS-232 port on
the rear panel. It can also be controlled by any
RS-232-enabled control system (e.g., Crestron,
AMX). Information on RS-232 operation is avail-
able to dealers on the Russound web site,
Before using the ST2S tuner with the
CAV6.6, you must assign source numbers
to Tuner 1 and 2 in the ST2 Setup Menu
AND complete the CAV6.6’s Source Setup
procedure to identify the tuner as a
“Peripheral“ device and assign Source
Numbers. The CAV6.6 (Rev. 3) requires
firmware version 2.01.16 or higher and
CAV6.6 (Rev. 4) requires firmware version
3.01.10 or higher to control each tuner
through RNET. The UNO-S2 keypad requires
firmware version 3.01.01 or higher.
BOX CONTENTS
The ST2S Tuner comes with the parts needed to
setup and operate the component. These
include:
• ST2 Tuner (SIRIUS module, AM/FM module)
• ST2-RC remote control
• 12VDC power supply
• AM loop antenna (1)
• FM antenna (1)
IR-controlled System
CAi Series -
The ST2S Tuner can be controlled by infrared
commands received through either of the two IR
connections on the rear panel. There are two
unique IR code sets for Tuner 1 and Tuner 2,
which allow each to be controlled independently
from either IR connection. These codes can be
learned from the ST2-RC remote control into the
CA-LRC1 remote control and/or the DSC and
DAN IR learning keypads. The ST2S contains two
individual tuners, which makes it act as two
sources in the CAi system. There are two source
audio outputs and two IR connections - one for
each tuner in the ST2S. You will need at least
one IR link cable (Russound P/N 09-0508) for
• SIRIUS antenna (1)
• RCA audio cable (2)
• Rack mount ears
Please call Russound at 800-638-8055 ext. 501
for assistance if parts are missing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2S FRONT PANEL
Mode
Band
ESPN Radio
1
2
3
4
5
6
7
8
9
10
11 12
13
Mode
Band
ESPN Radio
1
DROP-DOWN COVER - Hinged see-through cover protects the selection buttons on the tuner
MAIN POWER SWITCH - Turns power on and off
2
3
4
5
6
BANK SELECT BUTTON - Selects bank 1-6
MEMORY SELECT BUTTONS - Sets and selects memory presets 1-6 for each bank
POWER ON/OFF LED - Indicates power on or off
IR RECEIVER - Receives IR signal from remote control
7
8
9
LCD PANEL - 12-character backlit display shows station, channel, custom names, etc.
SIRIUS and AM/FM - Backlit tuner selection indicator
SELECT - Selects Tuner 1 (SIRIUS) or Tuner 2 (AM/FM), and accesses tuner setup menus
10
MEM PRESET UP/DOWN - Selects memory presets starting with last preset, and toggles
through menu features
11
MODE/BAND - (AM/FM) Selects AM or FM band
(SIRIUS) Selects a SIRIUS Mode (Category Search, Now Playing, Display Preferences)
(ALL) Enters menu selections when programming
12
13
TUNE UP/DOWN - (AM/FM) Manually selects radio stations
(SIRIUS) Manually selects channels (Channel Up/Channel Down)
(ALL) Toggles through menu settings
STEREO MON/EXIT SIGNAL - (AM/FM) Selects stereo/mono mode for AM/FM, and Distant/Local reception
(SIRIUS) Press to Exit current SIRIUS Mode, hold for signal strength
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2S REAR PANEL
2
3
4
5
6
7
8
9
10
11
1
ST2 Smart Tuner
Designed in USA
Made in China
FM Coax Loop Antenna
IR
L
R
IR
L
R
Serial
In
Out
75Ω
GND AM
Power 12VDC 1.25A
RNET Link
RS232 Interface
1
Keypad
2
Tuner 2
Tuner 1
TUNER 2 AM/FM
TUNER 1 SIRIUS
1
2
RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible,
displays frequency and other information on the UNO keypads
RS-232 INTERFACE - The RS-232 Interface allows the tuner to be controlled by PC or other devices
that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and program-
ming (DB9 Cable)
3
4
KEYPAD PORTS - RJ-45 Keypad ports for ST2-KP tuner keypads in dedicated, non-RNET sys-
tems (Do not connect UNO keypads to these ports)
FM COAX - FM Antenna threaded F-connection (75 ohms) for Tuner 2
LOOP ANTENNA - AM antenna connection (300 ohms) for Tuner 2
IR INPUT - IR control input (common IR control) for Tuner 2 or Tuner 1
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 2
SIRIUS ANTENNA - SIRIUS Antenna SMB connection (50 ohms) for Tuner 1
IR INPUT - IR control input (common IR control) for Tuner 1 or Tuner 2
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 1
POWER SUPPLY - 12VDC 1.25A max current draw external power supply connection
5
6
7
8
9
10
11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2-RC REMOTE CONTROL
1
2
POWER - Puts the tuner in/out of standby mode
1
2
TUNER CONTROL - Select TUNER 1 (SIRIUS) or
TUNER 2 (AM/FM) and all subsequent button
presses affect that tuner
3
4
5
6
7
8
NUMERIC INPUT - Number buttons for direct
selection of station, channel, bank, preset
PWR
BANK SELECT - Used for direct bank selection
(numeric input 1-6)
TUNER 1
TUNER 2
3
1
4
7
2
5
8
0
3
6
9
15
14
TUNE SELECT - Used for direct station or chan-
nel selection (numeric input)
4
5
TUNE UP/DOWN - Incrementally scrolls through
station or channel numbers
M
E
M
BANK
FAV 1/FAV 2 - Sets/Selects Favorite 1 or 2
preset selection on ST2S tuner
6
7
TUNE
AM/FM
SEEK UP/DOWN -
(AM/FM) Seeks the next tuned station
up/down
13
12
TUNE
FAV 1
SEEK
FAV 2
(SIRIUS) Scrolls through banks 1-6
9
SEEK
LOCAL/DISTANCE -
(AM/FM) Optimizes station reception
OK -
OK
8
9
LOC/
DX
ST/
MONO
10
TUNE
(AM/FM) Confirms direct entries
(SIRIUS) Operating mode toggle
11
10
11
STEREO/MONO -
(AM/FM) Selects stereo or mono broadcast
(SIRIUS) Exit current SIRIUS operating mode
12
13
TUNE UP/DOWN - Scrolls through station or
channel numbers
MEM UP/DOWN - Scrolls through preset sta-
tions within selected bank
14
15
AM/FM - Selects AM or FM band
MEM SELECT - Used for direct memory select
(numeric input 1-6)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
BASIC CONNECTIONS
Power
ST2-KP Keypad to ST2S Connection
(Non-RNET System)
To power the tuner, connect the 12VDC external
power supply by inserting the power supply jack
into the power supply connection on the tuner’s
rear panel.
Note: ST2-KP keypads are designed for use
with IR-controlled systems (non-RNET systems).
When the ST2S Tuner is a component of an
RNET system such as CAV6.6, the RNET-system
keypads are used.
Audio Output
Connect one end of a dual RCA audio cable to
the Tuner 1 Audio Output connection. Keep prop-
er channel identity. Attach the other end of the
RCA cables to the source input of the audio con-
trol system. Repeat the same procedure for the
Tuner 2 Audio Output.
The ST2-KP connects to the ST2S tuner with
CAT-5 cable, using an RJ-45 (T568A) jack on the
tuner connection end of the cable. Be sure to
use the keypad ports for the ST2-KP and NOT
the RNET link ports. The ST2S tuner supports
up to two ST2-KP keypads. An SA-ZX3 Keypad
Splitter can be used to add additional keypads.
RNET Connection
To link the ST2S to an RNET-compatible device,
use a CAT-5 passthrough patch cable with simi-
lar wiring terminations at each end. Connect one
end of the cable to the RNET Link In of the ST2
tuner, and connect the other end of the patch
cable to the RNET Link Out connection on the
RNET-compatible device.
Rack Mount Installation
The ST2S can be mounted in a standard compo-
nent rack using the rack ears provided. Line the
rack ear’s two rows of screw holes with the
three screw holes on the side of the tuner. Use
the screws provided to secure the rack ears
onto the unit on both sides. The ST2S tuner
should not be installed above a high heat-pro-
ducing component such as a power amplifier.
IR Connections
The ST2S Tuner can be controlled by infrared
commands received through the two IR connec-
tions on the rear panel. The ST2S Tuner compo-
nent contains two tuners, which must be set up
as two sources. There are two IR connections -
one for each tuner in the ST2S. You will need
two IR link cables (Russound P/N 09-0508) for
these connections. There is a unique IR code set
each for Tuner 1 and Tuner 2, which allow each
to be controlled independently. These codes can
be learned from the ST2-RC remote into learn-
ing-capable remotes and keypads.
If you are using an IR-controlled system from
another manufacturer, installation should be sim-
ilar. The ST2S IR codes may be learned into
many other manufacturers’ remote controls that
have learning capability for unified control over
the audio-video equipment.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
ST2-KP AND CAi CONNECTIONS
ST2 Smart Tuner
Designed in USA
Made in China
In
Out
RNET Link
RS232 Interface
1
Keypad
2
CAT-5 Cable
ST2-KP Connections to ST2S Tuner (Non-RNET Systems)
The diagram depicts a standard ST2-KP keypad connection to the keypad port on the back of the
ST2S. The keypad uses a 110 punchdown connection and an RJ-45 T568A connection to the tuner.
VOLUME
SOURCE
STORE
POWER
REMOTE SENSOR
ST2-KP
CA-LCD2
ST2 Smart Tuner
Designed in USA
Made in China
FM Coax Loop Antenna
IR
L
R
IR
L
R
Serial
In
Out
75Ω
GND AM
Power 12VDC 1.25A
RNET Link
RS232 Interface
1
Keypad
2
Tuner 2
Tuner 1
IR Link Cable
RCA Cable
RCA Cable
CA6.4i
NEWMARKET, NH U.S.A.
ZONE PREAMP
OUTPUTS
KEYPAD PORTS
SOURCE INPUTS
1
2
3
4
5
6
1
2
1
2
3
4
~220-240VAC
~110VAC
VARIABLE
FIXED
VARIABLE
R
L
R
FIXED
L
OUTPUT TO 8 OHM SPEAKER
1
2
3
4
5
6
VOLTAGE FUSE
LINK
OUT
MUTE
OUT
110V
F4A
IR EMITTERS
12V TRIG
IN
IN
220-240V F2A
WARNING : SHOCK HAZARD – DO NOT OPEN
~110VAC
~220-240VAC
~50-60Hz
400W
AVIS : RISQUE DE CHOC ELECTRIQUE –
NES PAS OUVRIR.
SERIAL #
RCA Cable
IR Link Cable
Pos (+)
Neg (–)
Source Connections with CAi Series Controller/Amplifier
The diagram depicts a typical setup using the ST2S Tuner with a CAi Series amplifier. Each tuner in
the ST2 unit must be connected as a separate source for audio inputs.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
CAV6.6 SERIES CONNECTIONS
UNO-S2
keypads
AM loop antenna
Sirius antenna
ST2 Smart Tuner
Designed in USA
FM Coax Loop Antenna
Serial
IR
L
R
IR
L
R
In
Out
Made in China
75Ω
GND AM
Power 12VDC 1.25A
RNET Link
RS232 Interface
1
Keypad
2
Tuner
2
Tuner
1
99:Horizons
ST2 Tuner
Tuner 2 is Source 2
RCA Cables
Tuner 1 is Source 1
CAV6.6
RCA Cable
Source Connections with CAV6.6 Controller/Amplifier (RNET System)
The diagram depicts a typical setup using the ST2S Tuner with a CAV6.6 amplifier. Each tuner in the
ST2 unit must be connected as a separate source for audio inputs. UNO-S2 keypads are connected
to the CAV6.6 keypad ports, NOT the ports on the ST2 Tuner.
NOTE: When viewed from the BACK, Tuner 1 output is on the RIGHT side of the ST2S, and the
Tuner 1 (Source 1) input is on the LEFT side of the source input section of the CAV6.6.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
AM Antenna
FM Antenna
Connect the included loop antenna for AM recep-
tion to the back panel, attaching the GND
(ground) and AM ends to the appropriate con-
nections for Tuner 2.
Attach the included FM antenna to the Tuner 2
FM COAX connection on the back panel by push-
ing the F-type quick-connect termination of the
antenna onto the FM connection.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best per-
formance for AM reception. Use a 75-ohm to
300-ohm balun at the AM connection on the
tuner, and attach the 75-ohm coax cable to the
balun.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best per-
formance for FM reception. Attach the desired
length of 75-ohm coax cable directly to the FM
connection on the tuner.
Sirius antenna
75 ohm
to 300 ohm
balun
ST2 Smart Tuner
Designed in USA
FM Coax Loop Antenna
IR
L
R
IR
L
R
Serial
In
Out
Made in China
75Ω
GND AM
Power 12VDC 1.25A
RNET Link
RS232 Interface
1
Keypad
2
Tuner
2
Tuner
1
Connecting an Indoor or Outdoor AM/FM Antenna
The diagram above depicts a typical setup using the ST2S Tuner with the included FM antenna and
AM loop antenna. Also shown are two outdoor AM/FM antenna options (not included). (Not to scale)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
SIRIUS Antenna
repeaters are used to boost the signal, which
can be received by antennas placed in or near
windows.
For SIRIUS radio reception, connect the included
SIRIUS antenna to the back panel of the SIRIUS
module. The antenna comes with 20 feet of
cable. If this length is not sufficient, there are
aftermarket antenna cable extension kits avail-
able for custom lengths.
SIRIUS Antenna Positioning
SIRIUS has three satellites over the contiguous
United States, plus terrestrial repeaters in major
metropolitan areas.
SIRIUS Antenna Installation
There are several methods available for antenna
To receive the strongest signal, the following
placement and installation. Regardless of method
used, it is best to experiment with positioning to
achieve the best signal possible before installa-
tion.
map is provided as a guideline for antenna place-
ment. It may be necessary to listen to SIRIUS for
a few days, at different times of the day, to
determine the optimal antenna placement for sig-
nal reception.
The SIRIUS antenna may be situated in or near a
window. In metropolitan areas, ground-located
SIRIUS Signal Strength Mode
The display shows one of the following:
To test the SIRIUS signal reception, turn the unit
on. When the SIRIUS radio is powered for the
first time, the SIRIUS service will start playing
Preview Channel 184, a preview/promotional
channel. Verify that Channel 184 is playing by
pressing the Tune Up/Tune Down buttons. Enter
Signal Strength Mode by pressing and holding
the ST/MONO button on the ST2S front panel.
EXCELLENT SIGNAL Signal strength good
GOOD SIGNAL
WEAK SIGNAL
NO SIGNAL
Signal strength marginal
Signal strength poor
Loss of signal
Adjust the antenna until EXCELLENT SIGNAL is
displayed. Press EXIT SIGNAL to exit Signal
Strength Mode.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
Grounding an Outdoor Antenna
If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges
and voltage surges. Consult the instructions that came with the antenna or contact the antenna manu-
facturer for proper installation instructions. The diagram gives a general depiction of how an outdoor
antenna should be grounded. For complete guidelines on antenna grounding procedures, please con-
sult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984.
Antenna Lead
In Wire
Electric
Service
Equipment
Grounding
Conductors
Ground
Clamps
Power Service
Grounding
Electrode System
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO OVERVIEW
SIRIUS Radio Activation
SIRIUS Radio delivers over 120 channels of digital entertainment - 65 channels with 100% commer-
cial-free music and 55 channels of news, sports and entertainment. SIRIUS radio is a subscription-
based service with a monthly provider fee and an activation charge. Billing and activation are done
directly through SIRIUS. SIRIUS radio broadcasts Channel 184 for preview but will not broadcast the
full range of channels without activation.
To activate the SIRIUS tuner:
Mode
Band
1
Turn on the power, select the SIRIUS Tuner, and press
to enter the SIRIUS Mode selection.
Scroll through the Modes until 4.SIRIUS ID appears. Release the button and the 12-digit
SIRIUS ID number appears on the display (e.g., 123456789012). Write the number down to
have it available when contacting SIRIUS Radio for activation. The number is also shown on the
back of the unit and on the product box.
2. Install the SIRIUS antenna and direct it skyward, using the location chart on page 13.
3. Tune the SIRIUS radio to channel 184, the Preview channel.
4. To subscribe, have a major credit card and your SIRIUS Radio ID number at hand and contact
1-888-539-7474. You will be guided through the activation process step by step.
5. A complete and up-to-date full channel listing is available on the SIRIUS Radio website,
SIRIUS Radio Displays
In addition to Channel and Category information, the SIRIUS tuner will broadcast operating condition
messages when the following conditions occur:
Display
Condition
ANTENNA ERROR
ACQUIRING SIGNAL
INVALID CHANNEL
UPDATING CHANNELS
CALL 888-539-SIRIUS TO SUBSCRIBE
SUBSCRIPTION UPDATED
Antenna not connected
Loss of signal, acquiring channel audio
Channel number not valid
Channel map update
Unsubscribed channel
Subscription update
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO MODES
SIRIUS Radio Modes
There are six user “modes” for selecting music, viewing music information, retrieving ID and locking
channels on the SIRIUS Tuner:
Preset (default or normal)
Category Search
Now Playing
Display Preferences
SIRIUS ID
Channel Lock
These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing EXIT and return to tuner display and Preset mode.
For all SIRIUS Modes
The chart below outlines the button presses for various SIRIUS tuner functions outside of the SIRIUS
modes.
ST2S
ST2-RC ST2-KP
UNO-S2
UNO-LRC1
All User Modes
Mode
Band
OK
Operating Mode Toggle
ST/
MONO
Exit Current Mode
Signal Strength
Hold
Hold
Hold
Operating Mode Toggle
This button press accesses the five non-default SIRIUS modes. The five modes will appear in order:
Category Search, Now Playing, Display Preferences, SIRIUS ID, and Channel Lock.
Exit Current Mode
This button press returns the SIRIUS tuner to Preset (default) mode.
Signal Strength
This button press and hold accesses the Signal Strength mode. Depending on the signal, the follow-
ing will be displayed:
EXCELLENT SIGNAL Signal strength good
GOOD SIGNAL Signal strength marginal
WEAK SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Press the appropriate button again to exit Signal Strength Mode.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO MODES
Preset (default) Mode
This is the normal operating mode of the SIRIUS tuner. In this mode the SIRIUS tuner operates similar-
ly to the AM/FM tuner for channel up and down, bank selection and memory presets.
Next Preset
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.
Previous Preset
This button press accesses the previous saved preset in the chosen bank
Next Bank
This button press accesses the next bank (total of 6 banks).
Previous Bank
This button press accesses the previous bank.
Channel Up
This button press accesses the next active channel up from the current channel.
Channel Down
This button press accesses the next active channel down from the current channel.
ST2S
ST2-RC
ST2-KP
UNO-S2
UNO-LRC1
Preset Mode
Next Preset
MEM
MEM
Previous Preset
Next Bank
Hold
Hold
Hold
Hold
Hold
Hold
Previous Bank
Channel Up
Channel Down
1.CAT SEARCH
Category Search Mode (
)
SIRIUS Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category
is a series of channels (e.g., The Vault, The Roadhouse, CNN). Channel selection in this mode
is refined to scrolling only those channels in the selected category.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO MODES
1.CAT SEARCH
Category Search Mode (
) (continued)
Next Category
This button press accesses the next category from the current category.
Previous Category
This button press accesses the previous category from the current category.
Category Channel Up
This button press accesses the next channel up within the selected category.
Category Channel Down
This button press accesses the next channel down within the selected category.
ST2S
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
Mode
Band
OK
Category Search Mode
Next Category
MEM
MEM
Previous Category
Category Channel Up
Category Channel Down
2.NOW PLAYNG
Now Playing Mode (
)
This mode displays information about the current SIRIUS selection. Appropriate button presses
access the next or previous information item.
NAME:
Displays the artist’s name, feature name or program name (news, talk, sports, etc.).
TITLE:
Displays the song title or program title.
CATEGORY:
Displays the current category.
ST2S
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
Mode
Band
OK
Now Playing Mode
Next Info Item
MEM
MEM
MEM
MEM
Previous Info Item
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO MODES
3.DSPLY PREF
Display Preference Mode (
)
This mode allows you to choose how SIRIUS channel information will be displayed on the keypad and
tuner. Appropriate button presses access the next or previous preference item.
Note: For any display configuration, the artist’s name and song title will scroll before the display
returns to the designated display format.
CH NUMBER:
Channel Number (
)
This selection displays the channel number only (e.g., CH070, CH103).
Channel Name (CH NAME:)
This selection displays the channel name only (e.g., SIRIUS Pops, Heart & Soul).
Channel Number and Name (#:CH NAME:)
This selection displays the channel number and name (e.g., 43:BackSpin, 121:ESPNews).
ST2S
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
Mode
Band
OK
Display Preference Mode
Next Display Preference
MEM
MEM
MEM
MEM
Previous Display Preference
4.SIRIUS ID
SIRIUS ID Mode (
)
This mode allows access to the SIRIUS Identification number for the SIRIUS module. This 12-digit
123456789012
number must be provided to SIRIUS during the activation procedure (Example:
)
ST2S
ST2-RC ST2-KP
UNO-S2
UNO-LRC1
SIRIUS ID Mode
Mode
Band
OK
SIRIUS ID Number
ST/
MONO
Exit Current Mode
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
SIRIUS RADIO MODES
5.CHAN LOCK
Channel Lock Mode (
)
This mode allows you to lock/unlock a channel or channels to prevent audio access. This parental
control is set/cleared with a four-digit code entered using the UNO-LRC1 or ST2-RC remote
controls. Channel to be locked/unlocked must be selected before beginning this procedure.
ST2S
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
Mode
Band
OK
Channel Lock Mode
Next Info Item
MEM
MEM
MEM
MEM
Previous Info Item
Lock Channel (LOCK CHAN:)
This selection appears when an unlocked channel is selected.
To LOCK a channel:
1. Select ENTER CODE. Using the UNO-LRC1 or ST2-RC remote control, enter the current four-digit
code (default is 0000).
2. Exit Channel Lock mode. The channel is now locked and will not appear when scrolling through
channels. If the channel is selected numerically from the remote control, the user must enter the
code to unlock access.
Unlock Channel (UNLOCK CHAN:)
This selection appears when a locked channel is selected
To UNLOCK a channel:
1. Use the remote control to access the channel. From the Channel Lock menu, select UNLOCK.
Enter the current four-digit code (default is 0000). This temporarily unlocks the channel; when the
channel is exited, it will lock again.
2. To fully unlock the channel, repeat the process above in step 1.
Change Code (CHANGE CODE:)
This selection allows you to enter a new four-digit code for locking/unlocking channels.
To change a code:
Mode
Band
OK
1. Select CHANGE CODE. Press
ENTER CODE appears.
on the ST2S,
on the ST2-RC or
on the UNO-LRC1.
2. Using the remote control, enter the new four-digit code. RE-ENTER appears. Enter the new code
again. SAVED appears and the ST2S returns to normal mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
FRONT PANEL CONTROLS
local mode. DISTANT or LOCAL appears briefly on the
screen when selecting mode. Normal operation is in
Distant mode. In cities, antennas can pick up multi-
path signals when they bounce off buildings and get
doubled. The Local mode limits the noise associated
with these reflected signals.
Front Panel Operation
Turning the unit on
To turn the unit on, push the On/Off button up on the
front panel. Pushing the On/Off button down turns the
tuner off.
Selecting the desired tuner
Bank/Memory Presets
Each tuner has six banks of preset memory settings,
and each bank holds six presets for a total of 36 pos-
sible presets for each tuner (72 total presets).
Presets are associated with the tuner that is selected
at the time the preset is saved.
From the front panel, use
to toggle between SIR-
IUS and AM/FM. A backlight shows behind the select-
ed label SIRIUS (green) or AM/FM (amber) to indicate
the active tuner. In addition, the LCD panel is also
backlit green for Tuner 1 and amber for Tuner 2.
Each time a tuner is selected the display will refresh
with the current station or preset, and all subsequent
memory preset entries will be associated with that
selected tuner.
Memory Preset programming
From the front panel, perform these steps:
1. Select a tuner using
.
Selecting the desired band (AM/FM only)
2. Use
to choose from one of six banks (1-6).2
Mode
Band
Push
to switch between AM and FM reception.
Mode
Band
3. If AM/FM, select the desired band using
.
Selecting a mode (SIRIUS)
4. Tune to the desired station or channel.
Mode
Band
Push
to select an SIRIUS operating mode.
5. Push the desired memory preset (M1 through M6)
button for more than 2 seconds. When the memory
preset is saved, the appropriate preset number (M1
through M6) and SAVED appears on the LCD. The
selected station setting reappears and the sound
resumes after the button is released.
Exiting a mode (SIRIUS)
Push
to exit the SIRIUS mode selection menu.
Signal Strength mode (SIRIUS)
Recalling a Memory Preset
Press and hold
and release. The display shows
the signal strength rating. To exit press
.
To recall a memory preset, use
to select the
desired bank, then press the desired preset button
(M1 to M6). In addition to direct selection, the memo-
Selecting the desired frequency or channel
Press and release
and
for manual tuning.
ry presets can be accessed by using
and
Selecting Stereo or Mono Output (AM/FM
only)
to scroll through all presets for the bank selected.
Backup and Restore
Once all of the tuner settings are completed, it may
be advisable to create a backup of the programmed
settings for future use. The backup will then be avail-
able in case tuner settings need to be restored. The
“RNET Backup Utility” is available through the
required are a DB9 male-to-female cable and laptop
or desktop PC.
Press and release
mono mode. STEREO or MONO appears briefly on the
screen when selecting mode.
to toggle between stereo and
Selecting Distant or Local Reception
(AM/FM only)
Press and hold
to toggle between distant and
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
ST2-RC REMOTE CONTROL
Frequency Seek (AM/FM only)
The SEEK function is performed by pressing and
ST2-RC Remote Control Operation
The ST2-RC remote control is the only means of
remote operation of the ST2S in a non--RNET system.
The ST2S front panel displays information for the
tuner that is receiving commands from the ST2-RC.
However, the ST2-RC commands do not change
which tuner is playing; that is done through the sys-
tem’s source selection.
releasing
to seek lower frequencies or
for
higher frequencies. SEEK tuning begins at the current
frequency, seeks upward and stops at the next tuned
station. Pushing
continues the SEEK function.
Once the highest frequency is reached, the tuner con-
tinues in SEEK mode at the lowest frequency.
Turning the unit on/off
Selecting Stereo or Mono Output
(AM/FM only)
To switch the ST2 tuner in or out of standby mode,
PWR
push
or any other button except TUNER 1 or
ST/
MONO
TUNER 2.
Press
to toggle between stereo and mono mode.
STEREO or MONO appears briefly on the screen when
selecting mode. Normal operation is in stereo mode.
On a preset, the stereo/mono setting is saved for
that preset.
Selecting the desired tuner
TUNER 1
TUNER 2
To control a tuner, push
or
. When
pressed, these buttons will be backlit green for Tuner
1 (SIRIUS) and amber for Tuner 2 (AM/FM). Each time
a tuner is selected, the next button press will refresh
the display with the current station or preset for that
tuner, and all subsequent button presses and memory
preset entries will be associated with that selected
tuner.
Selecting Distant or Local Reception
(AM/FM only)
LOC/
DX
Press
to toggle between Distant and Local
mode. DISTANT or LOCAL appears briefly on the
screen when selecting mode. Normal operation is in
Distant mode.
Selecting the desired band (AM/FM only)
Recalling a Memory Preset
To recall a memory preset, select the desired tuner,
AM/FM
Push
to switch between AM and FM reception.
Selecting the desired frequency or channel
BANK
press
and enter the desired bank number
Use
and
for manual tuning. To move quickly
M
EM
(1-6), then press
and enter the desired preset
through the stations or channels, press and hold
number (1 to 6). The memory presets can also be
either of the Tune buttons for more than 1.5 seconds.
MEM
MEM
accessed by using
and
to scroll through all
TUNE
To directly select a station or channel, press
,
presets for the selected bank.
and enter the two- or three-digit SIRIUS channel num-
ber, or the three- or four-digit station frequency
(1071 for 107.1, etc.). European regions use five-
digit station frequencies.
Saving Favorites
The remote control stores two “favorites” (similar to
memory presets) per tuner. These are set simply by
selecting either Tuner 1 or Tuner 2, setting the
Selecting a mode (SIRIUS)
FAV 1
desired frequency and pressing and holding
or
OK
Push
to select an SIRIUS operating mode.
FAV 2
until “FAV1 (2) saved” appears on the tuner.
Stored Favorites are then recalled by pressing either
Exiting a mode (SIRIUS)
ST/
MONO
FAV 1
FAV 2
Push
menu.
to exit the SIRIUS operating mode selection
or
.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
ST2-KP KEYPAD CONTROLS
ST2-KP Keypad Operation
4
Selecting a Bank
To select a bank, select the desired tuner, then press
1
Turning the keypad on/off
and hold
or
to select the desired bank. The
To activate the ST2-KP, press
power down the keypad display. The keypad remains
powered until the ST2S Tuner is turned off.
. Press
to
bank name will show on the display.
4
Recalling a Memory Preset
1
Selecting the desired tuner
To recall a memory preset, press and release
or
To select a different tuner, press and hold
. (If the
keypad has been hardware jumper-selected to Tuner
1 or Tuner 2, it will not switch between the two
tuners.) The backlight color of the display will be
green for Tuner 1 (SIRIUS) and amber for Tuner 2
(AM/FM). Each time a tuner is selected the display
will refresh with the current station or preset for that
tuner, and all subsequent button presses and memo-
ry preset entries will be associated with that selected
tuner.
to scroll through the presets for the selected
bank. (Memory presets must be stored for ST2-KP
recall)
5
ST2-KP Keypad Display
The 5-character backlit display shows frequency and
band, plus SIRIUS channel and mode information.
Messages scroll twice, then display the first 5 char-
acters.
2
Selecting the desired band (AM/FM)
Push
to switch between AM or FM band.
ST2-KP Keypad-Front Panel
2
Selecting a mode (SIRIUS)
Push
to select a SIRIUS operating mode.
2
Exiting a mode (SIRIUS)
5
Press and release
until EXIT is displayed to exit
CH120
the SIRIUS operating mode menu.
3
Selecting the desired frequency or
3
2
channel
Use
and
for manual tuning. To move quickly
or
3
through the channels, press and hold either
1
4
for more than 1.5 seconds. European frequen-
cies show in .05 MHz increments.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
UNO-S2 KEYPAD CONTROLS WITH CAV6.6
Frequency Seek (AM/FM only)
A press on will seek the next higher tune-
able station. If a tuneable station is not found,
CAV6.6-UNO-S2 Keypad Operation
NOTE: To control the ST2 Tuner through the
UNO-S2 keypad, the tuner must be configured
as a source using the CAV6.6 programming
steps.
end the SEEK function by pressing
Frequency Scan (AM/FM only)
To scan, press and hold then release
again.
Turning the unit on
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the UNO-S2 keypad will
bring the tuner out of standby mode.
. The
tuner scans through tuned stations with a 5-sec-
ond preview before moving to the next station.
Selecting the desired tuner
To end scanning, press
again.
On the UNO-S2 keypad, press
to select
Signal Strength Mode (SIRIUS)
either Tuner 1 (SIRIUS) or Tuner 2 (AM/FM) by
choosing the tuner’s preassigned source num-
ber.
To check SIRIUS signal strength, press and hold
then release. The display shows the signal
strength rating. To exit, press
Selecting a Bank
again.
Selecting the desired band (AM/FM only)
Push
to toggle between AM band and FM
To select a bank, press and hold
for bank
band reception.
up or
for bank down. The bank’s name will
Selecting a Mode (SIRIUS)
be temporarily displayed on the UNO-S2.
Push
to toggle between SIRIUS modes.
Recalling a Memory Preset
Exiting a Mode (SIRIUS)
Press
and
to scroll through the memo-
Press
until EXIT is displayed to
and release
ry presets for the selected bank. This procedure
will step through all of the presets in the current
bank, then loop back to start at the first one.
Only configured presets will be displayed.
exit SIRIUS mode selection menu.
Selecting the desired frequency or channel
Use
and
for manual tuning or channel
selection. The frequency or channel will appear
on the keypad and the active tuner. To move
quickly through the channels, press and hold
Mute
Press
to mute/unmute the tuner audio output.
either
or
for more than 1.5 seconds.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
UNO-S2 KEYPAD CONTROLS WITH CAV6.6
1
6
5
ESPN Radio
2
4
3
1
2
3
4
SCAN - (press and hold)
TUNER SELECTION - Select source number
(AM/FM) Scans through tuned stations with
5-second preview before next station
(SIRIUS) Signal Strength mode toggle
assigned to TUNER 1 (SIRIUS) or TUNER 2 (AM/FM)
TUNE UP/DOWN - Used for manual station or chan-
nel selection
5
MUTE - Mutes/unmutes tuner audio output
SELECT -
6
6
BANK SELECT - Used for bank selection (press and
hold)
(AM/FM) Selects AM or FM band
(SIRIUS) Operating mode toggle
MEM UP/DOWN - Scrolls through memory preset
stations (press)
4
SEEK - (press)
(AM/FM) Seeks next higher tuned station
(SIRIUS) Exit current SIRIUS mode
NOTE: UNO-S2 keypads are connected to the
CAV6.6 to control the ST2S through RNET.
UNO-S2 keypads do not connect directly to
the ST2 Tuner.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
UNO-LRC1 REMOTE CONTROL WITH CAV6.6
Frequency Seek (AM/FM only)
UNO-LRC1 Remote Control Operation
Turning the unit on
The SEEK function is performed by pressing and
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the UNO-LRC1 will bring
the tuner out of standby mode when used with the
UNO keypad.
releasing the Select
or
or
. Press
. To seek
for
higher frequency station press
lower frequencies. Tuning begins at the current fre-
quency, seeks upward (or downward) and stops at the
Selecting the desired tuner
next tuned station. Pushing
or
again con-
To select a tuner, push
and choose the source
tinues the SEEK function. Once the highest frequency
is reached, the tuner continues SEEK mode at the
lowest frequency.
number preassigned to Tuner 1 (SIRIUS) or Tuner 2
(AM/FM), or use the UNO numeric source inputs at
the bottom of the UNO-LRC1.
Frequency Scan (AM/FM only)
Selecting the desired band (AM/FM only)
To scan, press and hold then release
. The
Push
to toggle between AM/FM reception.
tuner scans through tuned stations with a 5-second
preview before moving to the next station. To end
Selecting a Mode (SIRIUS)
Push
,
or
to toggle between SIR-
scanning, press
again.
IUS operating modes.
Selecting a Bank
Exiting a Mode (SIRIUS)
To select a bank, press and hold
or for bank down.
for bank up
Press
menu.
or
to exit SIRIUS operating mode
Recalling a Memory Preset
Signal Strength mode (SIRIUS)
Press and hold
and release. The display shows
Press
and
or
and
to scroll
the signal strength rating. To exit press
.
through a loop of all the memory presets for the cur-
rently selected bank. Only configured presets will be
displayed.
Selecting the desired frequency or channel
Use the Channel
and
or
and
for manual tuning. To move quickly through the
channels, press and hold the button for more than
1.5 seconds. To directly select a station or channel,
enter the three- or four-digit channel or frequency
Mute
Press the
button to mute/unmute the tuner
audio output.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S OPERATION
UNO-LRC1 REMOTE CONTROL WITH CAV6.6
1
2
POWER - Power managed by CAV6.6
UNO SELECTION - UNO must be the
selected source for control of the
CAV6.6 and any connected compo-
nents. Select UNO before sending
UNO-LRC1 remote commands.
NUMERIC INPUT - Number buttons for direct
input of frequency, channel, preset, bank
3
TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations
4
5
EXIT - Exit SIRIUS operating mode
1
2
TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations
6
SELECT -
(AM/FM) Confirms numeric selection
(SIRIUS) Operating mode toggle
7
8
MENU - SIRIUS operating mode toggle
PLAY -
(AM/FM) Selects AM or FM band
(SIRIUS) Operating mode toggle
3
4
9
9
BANK UP/DOWN - Used for bank selection (press
and hold)
12
15
5
6
5
7
8
MEM UP/DOWN - Scrolls through memory pre-
sets for selected bank (press)
14
13
10
11
MUTE - Mutes/unmutes tuner audio output
SCAN - (SEEK - press, see #14 below)
(AM/FM) Scans through tuned stations with 5-
second preview before next station (press and
hold)
9
12
(SIRIUS) Exit SIRIUS operating mode
10
12
TUNER SELECTION - Select source number for
TUNER 1 (SIRIUS) or TUNER 2 (AM/FM)
11
13
14
INFO - SIRIUS Now Playing mode toggle
SEEK UP/DOWN -
(AM/FM) Seeks next tuned station up/down
(SIRIUS) Next/previous preset, category, info
item, display preference
15
GUIDE - SIRIUS Category Search mode toggle
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
ST2S Tuner Setup Menus
Note: The Setup Menu procedures must be performed from the ST2S Tuner front panel.
The ST2S Tuner Setup Menus provide setup and naming procedures for the ST2S main chassis, the
SIRIUS tuner module and the AM/FM tuner module. These procedures include source number assign-
ments, assigning a custom name to a memory preset or a bank, choosing a region for AM/FM opera-
tion (US or Euro), factory initialization and system information.
If the ST2S is used with a non-RNET system, the ST2S can be connected and operated without any
setup programming. Follow the setup menus if custom names are desired, or for system info.
If the ST2S is used with an RNET system such as CAV6.6, the following minimum setup must be
performed for the ST2S to be properly controlled by the CAV6.6.
1. ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.
2. CAV6.6 Source Setup Menu - Assign the corresponding source numbers to Tuner 1 and Tuner 2.
3. CAV6.6 Source Setup Menu - Assign command type PERIPHERAL to Tuner 1 and Tuner 2.
NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then to
the CAV6.6 (must be powered on last) to establish a connection.
6. Press the Tune Up/Down buttons to scroll
ST2 Chassis Setup Menu
through the source numbers 1-6.
Source Number (Chassis)
7. Press MODE/BAND to select the source num-
The Source Number procedure permits Tuner 1
ber (as assigned in the CAV6.6 setup process).
(SIRIUS) and Tuner 2 (AM/FM) to be assigned the
8. Repeat the process for the next tuner.
proper peripheral source identities as will be
9. Press SELECT to exit the Source Number
assigned in the CAV6.6 Source Setup.
menu.
Note: Each of the ST2S modules can be config-
ured as source number “unassigned” if the mod-
ule is used in another system (e.g., home the-
ater) or will not be used as a source in the RNET
Update Firmware (Chassis)
system.
The Update Firmware procedure allows the ST2
tuner’s OS firmware to be updated. The proce-
dure is performed using a DB9 serial cable with
one end connected to the RS-232 port on the
back of the tuner and the other connected to a
PC or laptop. If an OS firmware update is avail-
able, it can be obtained through the Document
ule firmware must be performed by an author-
ized Russound service facility.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MEM Up/Down
until SOURCE NUM appears on the tuner.
3. Press MODE/BAND. TUNER # appears.
4. Press the Tune Up/Down buttons to select the
Tuner # (Tuner 1 is SIRIUS, Tuner 2 is AM/FM).
5. Press MODE/BAND. SOURCE NUM appears.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press and Hold
Select button
ST2 Chassis Setup Procedures
TUNER
SETUP
Menu
SOURCE
NUM
Chassis
Setup
UPDATE
FIRMW
FACTORY
INIT
SYSTEM
INFO
Procedure
Procedure
Procedure
Procedure
Menu
Mode
Band
Mode
Band
Mode
Band
This
Procedure
returns the
ST2 Tuner
to its
HOLD
MODE
TUNER
#
Mode
Band
Factory
settings
After update
cycle Power
Mode
Band
Mode
Band
Mode
Band
Are you sure
SOURCE
NUM
Start
Mode
Band
Update
YES
NO
Mode
Band
Mode
Band
Cycle Power
Please wait
Cycle Power
1. Enter the Setup Menu by pressing and holding them to the factory default settings.
the SELECT button.
2. TUNER SETUP appears. Press MEM Up/Down
1. Enter the Setup Menu by pressing and holding
the SELECT button.
until UPDATE FIRMW appears on the tuner.
3. Press MODE/BAND to enter the UPDATE FIRMW 2. TUNER SETUP appears. Press MEM Up/Down
menu.
until FACTORY INIT appears on the tuner.
3. Press MODE/BAND to enter the FACTORY INIT
menu.
4. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
4. “Hold BAND” appears on the tuner.
5. While pressing and holding MODE/BAND,
“After update cycle power” appears on the tuner
display.
6. When “Start Update” appears on the tuner dis- selections.
play, start the update program. “Finished”
appears on the computer screen when complete. returns to the top of the Factory Init menu. A
7. Cycle power to the tuner.
5. Press MODE/BAND to select. A “No” selection
“Yes” begins the initialization.
6. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when com-
plete.
Factory Initialization (Chassis)
The Factory Initialization procedure allows the
erasure of all programmed settings and returns
7. Cycle power on the ST2S tuner.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Memory #.
System Info (Chassis)
9. Press MODE/BAND to advance. MEMORY
NAME appears again.
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
10. Press MODE/BAND to access the Memory
Name entry screen.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
3. Press MODE/BAND.
4. Press MODE/BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press MODE/BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press MODE/BAND at “Version” to view.
9. Press SELECT to exit the System Info menu.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character
position. Up to 12 characters can be entered
one by one. A blinking cursor indicates the place-
ment of the character being entered.
12. Press MODE/BAND when memory name is
entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press MODE/BAND to save memory name.
The Memory Name menu returns to the Memory
# prompt to name other presets, or press
SELECT to return to the Memory Name menu
start.
(END OF ST2 CHASSIS SETUP)
Tuner Setup Menu for SIRIUS
It is important to select the desired tuner
(Tuner 1 for SIRIUS) using the SELECT
button BEFORE accessing the Tuner Setup
Menus.
Bank Name (SIRIUS)
A custom name can be assigned to each of the
six banks of Tuner 1 (SIRIUS).
1. Enter the Setup Menu by pressing and holding
the SELECT button.
Memory Name (SIRIUS)
2. TUNER SETUP appears. Press MODE.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press MODE/BAND.
A memory preset must be created and saved
before it can be named (see page 21). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press MODE/BAND. BANK NAME appears
again.
8. Press MODE/BAND to access the Bank Name
entry screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MODE again.
3. MEMORY NAME appears on the tuner.
4. Press MODE/BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press MODE/BAND to advance. Memory #
appears.
8. Press the Tune Up/Down buttons to select a
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press Select
button to select
SiriusTuner
Sirius Setup Menu
Memory Name Procedure
TUNER
SETUP
Menu
SOURCE
NUM
Chassis
Setup
UPDATE
FIRMW
FACTORY
INIT
SYSTEM
INFO
Procedure
Procedure
Procedure
Procedure
Menu
Mode
Band
SYSTEM
Sirius
Setup
Menu
MEM
NAME
BANK
NAME
CONTROLLR
ID
DIAGNOSTICS
Procedure
FACTORY
INIT
INFO
Procedure
Procedure
Procedure
Procedure
Procedure
Mode
Band
SAVE
Mode
Band
MEMORY
NAME
Mode
Band
Mode
Band
Mode
Band
BANK #
MEMORY #
CHANGES?
Mode
Band
Selects
character
Selects
character
position
Repeat
for each
character
in name
10. Press MODE/BAND when bank name is
entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press MODE/BAND to save bank name. The
Bank Name menu returns to the Bank # prompt
to name other banks, or press SELECT to exit
the Bank Name menu.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press Select
Sirius Setup Menu
Bank Name Procedure
button to select
Sirius Tuner
Mode
Band
TUNER
SETUP
Menu
SOURCE
NUM
Chassis
Setup
UPDATE
FIRMW
FACTORY
INIT
SYSTEM
INFO
Procedure
Procedure
Procedure
Procedure
Menu
Mode
Band
SYSTEM
Sirius
Setup
Menu
MEM
NAME
BANK
NAME
CONTROLLR
ID
DIAGNOSTICS
Procedure
FACTORY
INIT
INFO
Procedure
Procedure
Procedure
Procedure
Procedure
Mode
Band
SAVE
Mode
Band
BANK
NAME
Mode
Band
Mode
Band
BANK #
CHANGES?
Mode
Band
Selects
character
Selects
character
position
Repeat
for each
character
in name
Controller ID (SIRIUS)
The Controller ID procedure is used to identify
the controller(s) that the SIRIUS tuner will
respond to.
Factory Initialization (SIRIUS)
The Factory Initialization procedure allows the
erasure of all programmed settings of the SIRIUS
tuner and returns them to the factory default set-
tings.
Note: For the SIRIUS module that is installed in
the ST2S chassis, “All Controllers” will be the
default setting.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MODE/BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until FACTORY INIT appears on the tuner.
Diagnostics (SIRIUS)
The Diagnostics procedure is for factory use only.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
4. Press MODE/BAND to enter the FACTORY INIT
menu.
manufacturing build properties.
5. “Are you sure” appears on the tuner. Using the 1. Enter the Setup Menu by pressing and holding
Tune Up/Down buttons, view the “Yes” and “No”
selections.
the SELECT button.
2. TUNER SETUP appears. Press MEM Up/Down
6. Press MODE/BAND to select. A “No” selection until SYSTEM INFO appears on the tuner.
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
3. Press MODE/BAND.
4. Press MODE/BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press MODE/BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press MODE/BAND at “Version” to view.
9. Press SELECT to exit the System Info menu.
7. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when com-
plete.
8. Cycle power on the ST2S tuner.
System Info (SIRIUS)
The System Info menu shows the SIRIUS module
(END OF SIRIUS TUNER SETUP)
Sirius Setup Menu
Controller, Diagnostics, Factory Initialization
and System Info Procedures
Press Select
button to select
Sirius Tuner
TUNER
SETUP
Menu
SOURCE
NUM
Chassis
Setup
UPDATE
FIRMW
FACTORY
INIT
SYSTEM
INFO
Procedure
Procedure
Procedure
Procedure
Menu
Mode
Band
SYSTEM
MEM
NAME
BANK
NAME
CONTROLLR
ID
DIAGNOSTICS
Procedure
FACTORY
INIT
Sirius
Setup
Menu
INFO
Procedure
Procedure
Procedure
Procedure
Procedure
Mode
Band
Mode
Band
Mode
Band
Mode
Band
All Contrlrs
Mode
This
Procedure
is for
This
Band
Procedure
returns the
ST2 Tuner
to its
Factory
use
ONLY
Factory
Mode
Band
settings
Are you
sure?
Yes or No
Mode
Band
Mode
Band
YES
NO
Mode
Band
Please
Wait
Cycle Power
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Tuner Setup Menu for AM/FM
It is important to select the desired tuner
(Tuner 2 for AM/FM) using the SELECT
button BEFORE accessing the Tuner Setup
Menus.
Bank Name (AM/FM)
A custom name can be assigned to each of the
six banks of Tuner 2 (AM/FM).
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MODE/BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press MODE/BAND.
Memory Name (AM/FM)
A memory preset must be created and saved
before it can be named (see page 21). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press MODE/BAND. BANK NAME appears
again.
8. Press MODE/BAND to access the Bank Name
entry screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
10. Press MODE/BAND when bank name is
entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press MODE/BAND to save bank name. The
Bank Name menu returns to the Bank # prompt
to name other banks, or press SELECT to exit
the Bank Name menu.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MODE again.
3. MEMORY NAME appears on the tuner.
4. Press MODE/BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press MODE/BAND to advance.
8. Press the Tune Up/Down buttons to select a
Memory #.
9. Press MODE/BAND to advance. MEMORY
NAME appears again.
10. Press MODE/BAND to access the Memory
Name entry screen.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
Region (AM/FM)
The Region procedure assigns either US or Euro
to the tuner. The difference between the two is
that US FM frequencies operate in .2 MHz incre-
ments, while European FM frequencies operate in
.05 MHz increments.
12. Press MODE/BAND when memory name is
entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press MODE/BAND to save memory name.
The Memory Name menu returns to the Memory
# prompt to name other presets, or press
SELECT to return to the Memory Name
menu start.
1. Enter the Setup Menu by pressing and holding
the SELECT button.
2. TUNER SETUP appears. Press MODE/BAND.
3. MEMORY NAME appears. Press MEM
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Up/Down until REGION appears on the tuner.
4. Press MODE/BAND.
5. Press the Tune Up/Down buttons to select
either US or EURO.
6. Press MODE/BAND to select. Press SELECT
to exit the REGION menu.
Backup and Restore
Once all of the tuner settings are completed, it
may be advisable to create a backup of the pro-
grammed settings for future use. The backup will
then be available in case tuner settings need to
be restored.
The backup and restore PC application “RNET
Backup” is available through the Document
a DB9 male-to-female cable and laptop or desk-
top PC.
(END OF AM/FM TUNER SETUP)
Press Select
button to select
AM/FM Setup Menu
AM/FM Tuner
Chassis
Setup
SYSTEM
INFO
TUNER
SETUP
Menu
SOURCE
NUM
UPDATE
FIRMW
FACTORY
INIT
Procedure
Procedure
Procedure
Procedure
Menu
Mode
Band
REGION
MEM
NAME
AM/FM
Setup
Menu
BANK
Procedure
NAME
Procedure
Procedure
Mode
Band
Mode
Band
Mode
Band
Mode
Band
MEMORY
NAME
Mode
Band
Mode
Band
BANK #
MEMORY #
Mode
Band
SAVE
CHANGES?
BANK
Mode
Band
Mode
Band
Mode
Band
BANK #
NAME
Selects
Mode
Band
character
Selects
character
Selects
character
position
Selects
character
position
Repeat
for each
character
in name
Mode
Band
Repeat
for each
character
in name
SAVE
Mode
Band
CHANGES?
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S TUNER PROGRAMMING
PROGRAMMING FOR CAV6.6 USE
NOTE: The CAV6.6 (Rev. 3) must have firmware version 2.01.16 or higher,
CAV6.6 (Rev. 4) must have firmware version 3.01.10 or higher,and UNO-S2
firmware must be version 3.01.01 or higher to control the ST2S Tuner. Use the
System Info Menu of the CAV6.6 to check the firmware version. If the firmware is
not the proper revision as noted here, visit the Document Center at
www.russound.com to obtain the latest version.
To Program the CAV6.6 to operate with the ST2S Tuner:
(refer to the CAV6.6 Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the
UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (SIR-
IUS) is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or SIRIUS). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note:
When the ST2S Tuner is used with the CAV6.6 or other RNET controller, it is configured as an RNET
command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave as a
fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique source
number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Each of the ST2S modules can be configured as source number “unassigned” if the module is used
in another system (e.g., home theater) or will not be used as a source in the RNET system.
Key Function Note:
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” com-
mand type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and
will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ST2S Smart Tuner
Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)
Weight: 7 lbs. (3.2kg)
Power Supply: 12VDC 1.25A
Frequency Range: AM 530 - 1710 kHz
FM 87.7 - 107.9 MHz
FM Antenna Impedance: 75 ohm unbalanced
Impedance: 300 ohm balanced
AM
Sensitivity @ S/N: 20dB 55 dBu
Image Rejection: 33dB
S/N Ratio: 45 dB
FM
Sensitivity @ S/N: 30 dB 6dB max 12 dBu
Image Rejection: 80 dB
S/N Ratio: 60 dB
SIRIUS
SIRIUS Band: 2320.00 - 2332.50 MHz
SIRIUS Antenna: 50-ohm SMB connection
37
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY & REPAIR
The Russound ST2S is fully guaranteed against all defects in materials and workmanship for two (2)
years from the date of purchase. During this period, Russound will replace any defective parts and
correct any defect in workmanship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its written instructions. If
service is necessary, it must be performed by Russound. The unit must be returned to Russound at
the owner's expense and with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing by an agency or per-
son not specifically authorized in writing by Russound.
This Warranty does not cover:
• Damage caused by abuse, accident, misuse, negligence,
or improper installation or operation
• Power surges and lightning strikes
• Normal wear and maintenance
• Products that have been altered or modified
• Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed
Russound sells products only through authorized Dealers and Distributors to ensure that customers
obtain proper support and service. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will not be honored or serviced
under existing Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and
labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with
a note explaining the nature of service required. Be sure to pack the unit in a corrugated container
with at least three (3) inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number.
Write this number on the shipping label and ship to:
Russound
ATTN: Service
5 Forbes Road
Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and techniques become avail-
able, Russound/FMP, Inc. reserves the right to revise system specifications without notice.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
39
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2S
SmartTuner
Installation Manual
Russound
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: [email protected]
© 2005 Russound® All rights reserved. All trademarks are property of their respective owners.
© 2005 SIRIUS Satellite Radio Inc. “SIRIUS” and the SIRIUS dog logo are registered trademarks of SIRIUS Satellite
Radio Inc.
28-1190
07/26/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|