Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Product Introduction..........................................................................................................4-5
Component Guide
ST2-XM Front Panel.............................................................................................................6
ST2-XM Rear Panel..............................................................................................................7
ST2-RC Remote Control.......................................................................................................8
ST2-XM Setup and Connections
Basic Connections...............................................................................................................9
ST2-KP and CAV6.6 ..........................................................................................................10
CAi Series and A-BUS Connections.....................................................................................11
Antenna Connections ....................................................................................................12-13
ST2-XM Operation
XM Radio Activation...........................................................................................................14
XM Radio Displays.............................................................................................................14
XM Radio Modes .........................................................................................................15-18
Front Panel Controls..........................................................................................................19
ST2-RC Remote Control.....................................................................................................20
ST2-KP Keypad Controls....................................................................................................21
UNO-S2 Keypad Controls with CAV6.6............................................................................22-23
UNO-LRC1 Remote Control with CAV6.6.........................................................................24-25
ST2-XM Tuner Programming
ST2 Chassis Setup Menu...................................................................................................26
Source Number .........................................................................................................26
Update Firmware .......................................................................................................26
Factory Initialization ...................................................................................................27
System Info...............................................................................................................28
Tuner Setup Menu for XM ..................................................................................................29
Memory Name...........................................................................................................29
Bank Name ...............................................................................................................30
Controller ID..............................................................................................................30
Diagnostics ...............................................................................................................30
Factory Initialization ...................................................................................................30
System Info...............................................................................................................31
Tuner Setup Menu for AM/FM.............................................................................................31
Memory Name...........................................................................................................31
Bank Name ...............................................................................................................32
Region ......................................................................................................................32
Backup and Restore .........................................................................................................33
Programming for CAV6.6 Use ............................................................................................34
Technical Specifications ....................................................................................................35
Warranty & Repair .............................................................................................................36
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
DESCRIPTION
gration. It can also be controlled by IR signals
received through the IR connections on the rear
panel from IR repeating system commonly used
in distributed audio systems.
Thank you for choosing the Russound ST2-XM
Smart Tuner. Whether you are adding radio to an
existing system, expanding a CAi Series system
or taking advantage of the CAV6.6’s robust
If the ST2-XM Tuner is part of an RNET-enabled
RNET™ communication link, the ST2-XM Tuner is system such as the CAV6.6-S2 system, the tuner
designed to meet your needs.
can be controlled through an RNET keypad such
as the UNO-S2.
The ST2-XM Tuner is like having two radios in
one. The AM/FM tuner provides broadcast of
local AM/FM stations, and the XM tuner delivers
The ST2 Tuner also has an RS-232 port to sup-
port fully bi-directional integration into whole-
all the diversity and choices available to XM radio house control systems such as Crestron® and
subscribers. The two modules share one set of
controls and display on the front of the unit, but
each runs independently. This arrangement
allows two different broadcasts at the same time
in a multi-room audio distribution system.
AMX®.
FEATURES
• AM/FM Tuner
• XM satellite radio
• Compact single rack unit chassis
• Six banks of six memory presets each per
tuner (72 total presets) for storing AM/FM
station settings or XM channels
• Custom names for presets and banks
• Two Favorite presets per tuner
• Stereo or mono mode
XM satellite radio provides over 100 channels of
music, news sports, comedy, talk and entertain-
ment. Its coast-to-coast coverage, digital quality
sound and many commercial-free music channels
make XM radio the choice for the discriminating
listener.
XM radio is a subscription-based service, and lis-
teners can subscribe by visiting XM on the web
www.xmradio.com or by calling XM’s Listener
Care at 800-852-9696.
• Local or distant mode
• Dedicated IR remote control
• Individual IR direct inputs for each tuner
• Front panel IR receiver
• Supports two ST2-KP optional tuner keypads
• RNET connections send tuner frequency and
control information to UNO keypad display
• RS-232 control and programming. User
settings can be backed up and restored.
In addition to the traditional AM/FM broadcast
tuner function and the XM satellite access, the
ST2-XM Tuner can store up to 72 favorites, or
memory presets. These are stored in groups of
six called banks. There are six banks for each
tuner. Each preset and each bank can be given a INSTALLATION APPLICATIONS
custom name of your choice.
RNET-enabled System
When the ST2-XM Tuner is used with an RNET-
The ST2-XM Tuner can be controlled from the
front panel or by the dedicated ST2-KP tuner key- enabled device such as the CAV6.6 and is con-
pad. It can also be controlled by the ST2-RC IR
remote aimed at the tuner’s front panel IR receiv-
er. The ST2-RC IR codes can be learned into any
IR learning remote control for easy system inte-
nected to it through the Link In or Link Out port,
the tuner will be controlled by the CAV6.6
through the UNO-S2 keypad. Through RNET,
tuner information such as Tuner 1 or 2, station
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
frequency or channel, preset names and AM/FM
band or XM is displayed on UNO-S2 keypads. An
additional RNET device can be connected to an
existing ST2 by using the Link Out of the first
unit into the Link In of the second unit.
tem with an audio distribution hub such as the
A-H484 and IR-repeating keypads such as the
A-KP2. The connections on the rear panel are
designed to receive IR signals from a repeating
system commonly used in A-BUS distributed
audio systems.
Before using the ST2-XM tuner with the
CAV6.6, you must assign source numbers
to Tuner 1 and 2 in the ST2 Setup Menu
AND complete the CAV6.6’s Source Setup
procedure to identify the tuner as a
“Peripheral“ device and assign Source
Numbers. The CAV6.6 requires firmware
version 2.00.01 or higher to control each
tuner through RNET. The UNO-S2 keypad
requires firmware version 3.00.01 or
higher.
For A-BUS applications, as with the CAi series
installation, the two tuners in the ST2-XM unit
must be set up as two sources, with two source
audio inputs and two IR connections. You will
need two IR link cables for these connections.
The two IR code sets can be learned from the
ST2-RC remote into the A-LRC1 remote control.
Note: Optional ST2-KP keypads can be used to
provide control for the ST2-XM Tuner and are
designed to be used with IR-controlled systems.
IR-controlled System
CAi Series -
RS-232 Controlled System
The ST2-XM Tuner can be controlled by infrared
commands received through either of the two IR
connections on the rear panel. There are two
unique IR code sets for Tuner 1 and Tuner 2,
which allow each to be controlled independently
from either IR connection. These codes can be
learned from the ST2-RC remote control into the
CA-LRC1 remote control and/or the DSC and
DAN IR learning keypads. The ST2-XM contains
two individual tuners, which makes it act as two
sources in the CAi system. There are two source
audio outputs and two IR connections - one for
each tuner in the ST2-XM. You will need at least
one IR link cable (Russound P/N 09-0508) for
these connections (one is supplied with each CAi
system). If you are using an IR-controlled system
from another manufacturer, installation should be
similar. The ST2-XM IR codes may be learned
into many other manufacturers’ remote controls
that have learning capability for unified control
over the A/V equipment.
The ST2-XM Tuner can be controlled using the
RNET protocol provided via the RS-232 port on
the rear panel. It can also be controlled by any
RS-232-enabled control system (e.g., Crestron,
AMX). Information on RS-232 operation is avail-
able to dealers on the Russound web site,
BOX CONTENTS
The ST2-XM Tuner comes with the parts needed
to setup and operate the component. These
include:
• ST2 Tuner (AM/FM module, XM module)
• ST2-RC remote control
• 12VDC power supply
• AM loop antenna (1)
• FM antenna (1)
• XM antenna (1)
• RCA audio cable (2)
• Rack mount ears
®
A-BUS System -
The ST2-XM Tuner can be used in an A-BUS sys-
Please call Russound at 800-638-8055 ext. 501
for assistance if parts are missing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2-XM FRONT PANEL
1
2
3
XM
64 : The Groove
AM/FM
5
6
4
7
8
9
10
XM
64 : The Groove
AM/FM
13
12
11
1
MAIN POWER SWITCH - Turns power on and off
POWER ON/OFF LED - Indicates power on or off
2
3
4
5
6
REMOVABLE COVER LENS - Covers the selection buttons on the tuner
BANK SELECT BUTTON - Selects bank 1-6
MEMORY SELECT BUTTONS - Sets and selects memory presets 1-6 for each bank
IR RECEIVER - Receives IR signal from remote control
7
8
LCD PANEL - 12-character backlit display shows station, channel, custom names, etc.
XM and AM/FM - Backlit tuner selection indicator
9
TNR SEL - Selects Tuner 1 (XM) or Tuner 2 (AM/FM), and accesses tuner setup menus
10
BAND - (AM/FM) Selects AM or FM band
(XM) Selects an XM Mode (Category Search, Now Playing, Display Preferences)
(ALL) Enters menu selections when programming
11
ST/MONO - (AM/FM) Selects stereo or mono mode for AM/FM, and Distant/Local reception
(XM) Press to Exit current XM Mode, hold for signal strength
12
13
MEM PRESET UP/DOWN - Selects memory presets starting with last preset, and toggles
through menu features
TUNE UP/DOWN - (AM/FM) Manually selects radio stations
(XM) Manually selects channels (Channel Up/Channel Down)
(ALL) Toggles through menu settings
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2-XM REAR PANEL
2
3
4
5
6
7
8
9
10
11
1
LOOP
Serial#
12VDC 1.5A
TUNER 2
TUNER 1
AUDIO OUTPUT
ST2 Smart Tuner
NEWMARKET, NH U.S.A.
LINK
ANTENNA
FM COAX
AUDIO OUTPUT
RS-232
KEYPAD PORTS
L
R
L
R
IR
INTEFACE
IR
ANTENNA
IN
OUT
TUNER 2 AM/FM
TUNER 1 XM
1
RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible, dis-
plays frequency and other information on the UNO keypads
2
RS-232 INTERFACE - The RS-232 Interface allows the tuner to be controlled by PC or other devices
that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and program-
ming (DB9 Cable)
3
4
KEYPAD PORTS - RJ-45 Keypad ports for ST2-KP tuner keypads in dedicated, non-RNET sys-
tems (Do not connect UNO keypads to these ports)
FM COAX - FM Antenna threaded F-connection (75 ohms) for Tuner 2
LOOP ANTENNA - AM antenna connection (300 ohms) for Tuner 2
IR INPUT - IR control input (common IR control) for Tuner 2 or Tuner 1
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 2
XM ANTENNA - XM Antenna SMB connection (50 ohms) for Tuner 1
IR INPUT - IR control input (common IR control) for Tuner 1 or Tuner 2
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 1
POWER SUPPLY - 12VDC external power supply connection
5
6
7
8
9
10
11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPONENT GUIDE
ST2-RC REMOTE CONTROL
1
2
POWER - Puts the tuner in/out of standby mode
1
2
TUNER CONTROL - Select TUNER 1 (XM) or
TUNER 2 (AM/FM) and all subsequent button
presses affect that tuner
3
4
5
6
7
8
NUMERIC INPUT - Number buttons for direct
selection of station, channel, bank, preset
PWR
BANK SELECT - Used for direct bank selection
(numeric input 1-6)
TUNER 1
TUNER 2
3
1
4
7
2
5
8
0
3
6
9
TUNE SELECT - Used for direct station or chan-
nel selection (numeric input)
15
14
4
5
TUNE UP/DOWN - Incrementally scrolls through
station or channel numbers
M
E
M
BANK
FAV 1/FAV 2 - Sets/Selects Favorite 1 or 2
preset selection on ST2-XM tuner
6
7
TUNE
SEEK UP/DOWN -
AM/FM
(AM/FM) Seeks the next tuned station
up/down
13
12
TUNE
FAV 1
SEEK
FAV 2
(XM) Scrolls through banks 1-6
9
LOCAL/DISTANCE -
SEEK
OK
(AM/FM) Optimizes station reception
8
9
10
OK -
LOC/
DX
ST/
MONO
TUNE
(AM/FM) Confirms direct entries
(XM) Operating mode toggle
11
10
11
STEREO/MONO -
(AM/FM) Selects stereo or mono broadcast
(XM) Exit current XM operating mode
12
13
TUNE UP/DOWN - Scrolls through station or
channel numbers
MEM UP/DOWN - Scrolls through preset sta-
tions within selected bank
14
15
AM/FM - Selects AM or FM band
MEM SELECT - Used for direct memory select
(numeric input 1-6)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM SETUP AND CONNECTIONS
BASIC CONNECTIONS
Power
ST2-KP RJ-45 Connection Wiring
To power the tuner, connect the 12VDC external
power supply by inserting the power supply jack
into the power supply connection on the tuner’s
rear panel.
Audio Output
Connect one end of a dual RCA audio cable to
the Tuner 1 Audio Output connection. Keep prop-
er channel identity. Attach the other end of the
RCA cables to the source input of the audio con-
trol system. Repeat the same procedure for the
Tuner 2 Audio Output.
IR Connections
ST2-KP Keypad to ST2-XM Connection
(Non-RNET System)
The ST2-XM Tuner can be controlled by infrared
commands received through the two IR connec-
tions on the rear panel. The ST2-XM Tuner com-
ponent contains two tuners, which must be set
up as two sources. There are two IR connec-
tions - one for each tuner in the ST2-XM. You will
need two IR link cables (Russound P/N 09-0508)
for these connections. There is a unique IR code
set each for Tuner 1 and Tuner 2, which allow
each to be controlled independently. These
codes can be learned from the ST2-RC remote
into learning-capable remotes and keypads.
If you are using an IR-controlled system from
another manufacturer, installation should be sim-
ilar. The ST2-XM IR codes may be learned into
many other manufacturers’ remote controls that
have learning capability for unified control over
the A/V equipment.
The ST2-KP connects to the ST2-XM tuner with
CAT-5 cable, using an RJ-45 (T568A) jack on the
tuner connection end of the cable. Be sure to
use the keypad ports for the ST2-KP and NOT
the RNET link ports. The ST2-XM tuner supports
up to two ST2-KP keypads. An SA-ZX3 Keypad
Splitter can be used to add additional keypads.
Note: ST2-KP keypads are designed for use
with IR-controlled systems (non-RNET systems).
When the ST2-XM Tuner is a component of an
RNET system such as CAV6.6, the RNET-system
keypads are used.
Rack Mount Installation
The ST2-XM can be mounted in a standard com-
ponent rack using the rack ears provided. Line
the rack ear’s two rows of screw holes with the
three screw holes on the side of the tuner. Use
the screws provided to secure the rack ears
onto the unit on both sides. The ST2-XM tuner
should not be installed above a high heat-pro-
ducing component such as a power amplifier.
RNET Connection
To link the ST2-XM to an RNET-compatible
device, use a CAT-5 passthrough patch cable
with similar wiring terminations at each end.
Connect one end of the cable to the RNET Link
In of the ST2 tuner, and connect the other end
of the patch cable to the RNET Link Out connec-
tion on the RNET-compatible device.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM SETUP AND CONNECTIONS
ST2-KP AND CAV6.6 CONNECTIONS
CAT-5 Cable
ST2-KP Connections to ST2-XM Tuner (Non-RNET Systems)
The diagram depicts a standard ST2-KP keypad connection to the keypad port on the back of the
ST2-XM. The keypad uses a 110 punchdown connection and an RJ-45 T568A connection to the tuner.
UNO-S2
keypads
64:The Groove
ST2 Tuner
CAV6.6
RCA Cable
Source Connections with CAV6.6 Controller/Amplifier (RNET System)
The diagram depicts a typical setup using the ST2-XM Tuner with a CAV6.6 amplifier. Each tuner in
the ST2 unit must be connected as a separate source for audio inputs. UNO-S2 keypads are connect-
ed to the CAV6.6 keypad ports, NOT the ports on the ST2 Tuner.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM SETUP AND CONNECTIONS
CAi SERIES AND A-BUS CONNECTIONS
VOLUME
SOURCE
STORE
POWER
REMOTE SENSOR
ST2-KP
CA-LCD2
LOOP
ANTENNA
Serial#
TUNER
2
TUNER
1
ST2 Smart Tuner
NEWMARKET, NH U.S.A.
LINK
FM COAX
AUDIO OUTPUT
AUDIO OUTPUT
RS-232
KEYPAD PORTS
L
R
L
R
INTERFACE
IR
IR
12VDC 1.5A
ANTENNA
IN
OUT
IR Link Cable
RCA Cable
RCA Cable
CA6.4i
NEWMARKET, NH U.S.A.
ZONE PREAMP
OUTPUTS
KEYPAD PORTS
SOURCE INPUTS
1
2
3
4
5
6
1
2
1
2
3
4
~220-240VAC
~110VAC
VARIABLE
FIXED
VARIABLE
R
L
R
FIXED
L
OUTPUT TO
3
8
OHM SPEAKER
4
1
2
5
6
VOLTAGE FUSE
110V F4A
220-240V F2A
LINK
OUT
MUTE
OUT
IR EMITTERS
12V TRIG
IN
IN
WARNING : SHOCK HAZARD – DO NOT OPEN
~110VAC
~220-240VAC
~50-60Hz
400W
AVIS : RISQUE DE CHOC ELECTRIQUE –
NES PAS OUVRIR.
SERIAL #
RCA Cable
IR Link Cable
Pos (+)
Neg (–)
Source Connections with CAi Series Controller/Amplifier
The diagram depicts a typical setup using the ST2-XM Tuner with a CAi Series amplifier. Each tuner in
the ST2 unit must be connected as a separate source for audio inputs.
A-KP2
ST2-KP
LOOP
LOOP
Serial#
TUNER
2
TUNER
1
ST2 Smart Tuner
NEWMARKET, NH U.S.A.
LINK
ANTENNA
ANTENNA
FM COAX
FM COAX
AUDIO OUTPUT
AUDIO OUTPUT
RS-232
KEYPAD PORTS
L
R
L
R
INTERFACE
IR
IR
12VDC 1.5A
IN
OUT
RCA Cable
RCA Cable
IR Link Cable
IR Link Cable
SOURCE AUDIO INPUT
NEWMARKET, NH U.S.A.
LINK
L
IN
OUT
R
TRIGGER OUT
12VDC
100mA
1
2
3
4
SYSTEM ON
SOURCE IR
COMMON IR
4
COUPLED-ZONE, 4-SOURCE
PANEL MOUNT AUDIO HUB
A/B COUPLED-ZONE OUTPUT
2A 3A
1A
4A
POWER FOR
KEYPADS
A
OUTPUT TO
KEYPADS
A
RCA Cable
IR Link Cable
+24V
4A
Pos (+)
Neg (–)
OUTPUT TO
BKEYPADS
POWER FOR
1B
2B
3B
4B
B
KEYPADS
SERIAL#
A-H484
Source Connections with A-BUS Audio Distribution Hub
The diagram depicts a typical setup using the ST2-XM Tuner with an A-BUS system’s audio distribu-
tion hub. Each tuner in the ST2 unit must be connected as a separate source for audio and IR inputs.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
XM Antenna
XM Signal Strength Mode
Connect the included XM antenna for XM recep-
tion to the back panel of the XM module. The
antenna comes with 20 feet of cable. If this
length is not sufficient, there are aftermarket
antenna kits available for custom lengths.
Position the antenna near a south-facing window
to receive the best signal from a satellite or ter-
restrial signal.
To test the XM reception, turn the unit on. When
the XM radio is powered for the first time, the
XM service will start playing XM Channel 1, a
preview/promotional channel. Verify that Channel
1 is playing by pressing the Tune Up/Tune Down
buttons. Enter Signal Strength Mode by pressing
and holding the ST/MONO button on the ST2-XM
front panel. The display shows one of the follow-
ing:
The antenna may also be attached to an exter-
nal wall by sliding the slots on the back of the
antenna onto four screws mounted on an exteri-
or wall. Establish the best receiving position for
the antenna before attaching it to the wall.
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Adjust the antenna until GOOD SIGNAL is dis-
played. Press ST/MONO to exit Signal Strength
Mode.
75 ohm
to 300 ohm
balun
Connecting an Indoor and Outdoor Antenna
The diagram above depicts a typical setup using the ST2-XM Tuner with the included XM antenna, FM
antenna and AM loop antenna. Also shown are two outdoor antenna options (not included).
(Not to scale)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
AM Antenna
FM Antenna
Connect the included loop antenna for AM recep-
tion to the back panel, attaching the GND
Attach the included FM antenna to the Tuner 2
FM COAX connection on the back panel by push-
(ground) and AM ends to the appropriate connec- ing the F-type quick-connect termination of the
tions for Tuner 2.
antenna onto the FM connection.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best per-
formance for AM reception. Use a 75-ohm to
300-ohm balun at the AM connection on the
tuner, and attach the 75-ohm coax cable to the
balun.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best per-
formance for FM reception. Attach the desired
length of 75-ohm coax cable directly to the FM
connection on the tuner.
Antenna
Lead In Wire
Electric
Service
Equipment
Power Service
Grounding
Electrode System
Grounding
Conductors
Ground
Clamps
Grounding an Outdoor Antenna
If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges
and voltage surges. Consult the instructions that came with the antenna or contact the antenna manu-
facturer for proper installation instructions. The diagram gives a general depiction of how an outdoor
antenna should be grounded. For complete guidelines on antenna grounding procedures, please con-
sult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
XM RADIO OVERVIEW
XM Radio Activation
XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depend-
ing on location) transferred by terrestrial antennas. The radio is a subscription-based service with a
monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but
will not broadcast the full range of channels without activation. Activation and billing are handled sole-
ly through XM Radio.
To activate the XM tuner:
1
Turn on the power, select the XM Tuner, and select channel 0. The tuner’s eight-character XM
satellite Radio ID number will appear on the display. Write the number down to have it available
when contacting XM Radio for activation. The number is also shown on the back of the unit and
on the product box.
2. To subscribe, have a major credit card and your XM Radio ID number at hand and contact XM at
1-800-852-9696. You will be guided through the activation process step by step.
3. A complete and up-to-date full channel listing is available on the XM Radio website,
XM Radio Displays
In addition to Channel and Category information, the XM tuner will broadcast operating condition mes-
sages when the following conditions occur:
Display
ANTENNA
UPDATING
LOADING
OFF AIR
CH - - -
Condition
Antenna not connected
Updating encryption code
Acquiring channel audio or information
Channel not in service
Channel (SID) no longer available
Corresponding Artist Name or Song Title are null (empty)
No channel available for the chosen category
- - - - - -
- - - - - -
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
XM RADIO MODES
XM Radio Modes
There are four user “modes” for selecting music and viewing music information on the XM Tuner:
Preset (default or normal)
Category Search
Now Playing
Display Preferences.
These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing EXIT and return to tuner display and Preset mode.
For all XM Modes
The chart below outlines the button presses for various XM tuner functions outside of the XM modes.
ST2-XM
ST2-RC ST2-KP
UNO-S2
UNO-LRC1
All User Modes
OK
Operating Mode Toggle
ST/
MONO
Exit Current Mode
Signal Strength
Hold
Hold
Hold
Operating Mode Toggle
This button press accesses the three non-default XM modes. The three modes will appear in order:
Category Search, Now Playing and Display Preferences.
Exit Current Mode
This button press returns the XM tuner to Preset (default) mode.
Signal Strength
This button press and hold accesses the Signal Strength mode. Depending on the signal, the follow-
ing will be displayed:
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Press the appropriate button again to exit Signal Strength Mode.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
XM RADIO MODES
Preset (default) Mode
This is the normal operating mode of the XM tuner. In this mode the XM tuner operates similarly to
the AM/FM tuner for channel up and down, bank selection and memory presets.
Next Preset
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.
Previous Preset
This button press accesses the previous saved preset in the chosen bank
Next Bank
This button press accesses the next bank (total of 6 banks).
Previous Bank
This button press accesses the previous bank.
Channel Up
This button press accesses the next active channel up from the current channel.
Channel Down
This button press accesses the next active channel down from the current channel.
ST2-XM
ST2-RC
ST2-KP
UNO-S2
UNO-LRC1
Preset Mode
Next Preset
MEM
MEM
Previous Preset
Next Bank
Hold
Hold
Hold
Hold
Hold
Hold
Previous Bank
Channel Up
Channel Down
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
XM RADIO MODES
1.CAT SEARCH
Category Search Mode (
)
XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is
a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this
mode is refined to scrolling only those channels in the selected category.
Next Category
This button press accesses the next category from the current category.
Previous Category
This button press accesses the previous category from the current category.
Category Channel Up
This button press accesses the next channel up within the selected category.
Category Channel Down
This button press accesses the next channel down within the selected category.
ST2-XM
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
OK
Category Search Mode
Next Category
MEM
MEM
Previous Category
Category Channel Up
Category Channel Down
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
XM RADIO MODES
2.NOW PLAYNG
Now Playing Mode (
)
This mode displays information about the current XM selection. Appropriate button presses access
the next or previous information item.
NAME:
Displays the artist’s name, feature name or program name (news, talk, sports).
TITLE:
Displays the song title or program title.
CATEGORY:
Displays the current category.
ST2-XM
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
OK
Now Playing Mode
Next Info Item
MEM
MEM
MEM
MEM
Previous Info Item
3.DSPLY PREF
Display Preference Mode (
)
This mode allows you to choose how XM channel information will be displayed on the keypad and
tuner. Appropriate button presses access the next or previous preference item.
Note: For any display configuration, the artist’s name and song title will scroll before the display
returns to the designated display format.
Channel Number (CH NUMBER:)
This selection displays the channel number only (e.g., XM070, XM103).
Channel Name (CH NAME:)
This selection displays the channel name only (e.g., ESPN Radio, Real Jazz).
Channel Number and Name (#:CH NAME:)
This selection displays the channel number and name (e.g., 64:The Groove, 121:Fox News).
ST2-XM
ST2-RC
ST2-KP UNO-S2
UNO-LRC1
OK
Display Preference Mode
Next Display Preference
MEM
MEM
MEM
MEM
Previous Display Preference
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
FRONT PANEL CONTROLS
screen when selecting mode. Normal operation is in
Distant mode. In cities, antennas can pick up multi-
path signals when they bounce off buildings and get
doubled. The Local mode limits the noise associated
with these reflected signals.
Front Panel Operation
Turning the unit on
To turn the unit on, push the On/Off button up on the
front panel. Pushing the On/Off button down turns the
tuner off.
Bank/Memory Presets
Selecting the desired tuner
Each tuner has six banks of preset memory settings,
and each bank holds six presets for a total of 36 pos-
sible presets for each tuner (72 total presets).
Presets are associated with the tuner that is selected
at the time the preset is saved.
From the front panel, use
to toggle between XM
and AM/FM. A backlight shows behind the selected
label XM (green) or AM/FM (amber) to indicate the
active tuner. In addition, the LCD panel is also backlit
green for Tuner 1 and amber for Tuner 2. Each time a
tuner is selected the display will refresh with the cur-
rent station or preset, and all subsequent memory
preset entries will be associated with that selected
tuner.
Memory Preset programming
From the front panel, perform these steps:
1. Select a tuner using
.
Selecting the desired band (AM/FM only)
2. Use to choose from one of six banks (1-6).
Push
to switch between AM and FM reception.
3. If AM/FM, select the desired band using
.
Selecting a mode (XM)
4. Tune to the desired station or channel.
5. Push the desired memory preset (M1 through M6)
button for more than 2 seconds. When the memory
preset is saved, the appropriate preset number (M1
through M6) and SAVED appears on the LCD. The
selected station setting reappears and the sound
resumes after the button is released.
Push
to select an XM operating mode.
Exiting a mode (XM)
Push
to exit the XM mode selection menu.
Signal Strength mode (XM)
Recalling a Memory Preset
Press and hold
and release. The display shows
the signal strength rating. To exit press
.
To recall a memory preset, use
to select the
desired bank, then press the desired preset button
(M1 to M6). In addition to direct selection, the memo-
Selecting the desired frequency or channel
Press and release
and
for manual tuning.
ry presets can be accessed by using
scroll through all presets for the bank selected.
and
to
Selecting Stereo or Mono Output (AM/FM
only)
Backup and Restore
Once all of the tuner settings are completed, it may
be advisable to create a backup of the programmed
settings for future use. The backup will then be avail-
able in case tuner settings need to be restored. The
“RNET Backup Utility” is available through the
required are a DB9 male-to-female cable and laptop
or desktop PC.
Press and release
mono mode. STEREO or MONO appears briefly on the
screen when selecting mode.
to toggle between stereo and
Selecting Distant or Local Reception
(AM/FM only)
Press and hold
local mode. DISTANT or LOCAL appears briefly on the
to toggle between distant and
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
ST2-RC REMOTE CONTROL
Frequency Seek (AM/FM only)
The SEEK function is performed by pressing and
ST2-RC Remote Control Operation
The ST2-RC remote control is the only means of
remote operation of the ST2-XM in a non--RNET sys-
tem. The ST2-XM front panel displays information for
the tuner that is receiving commands from the ST2-
RC. However, the ST2-RC commands do not change
which tuner is playing; that is done through the sys-
tem’s source selection.
releasing
to seek lower frequencies or
for
higher frequencies. SEEK tuning begins at the current
frequency, seeks upward and stops at the next tuned
station. Pushing
continues the SEEK function.
Once the highest frequency is reached, the tuner con-
tinues in SEEK mode at the lowest frequency.
Turning the unit on/off
Selecting Stereo or Mono Output
(AM/FM only)
To switch the ST2 tuner in or out of standby mode,
PWR
push
or any other button except TUNER 1 or
ST/
MONO
TUNER 2.
Press
to toggle between stereo and mono mode.
STEREO or MONO appears briefly on the screen when
selecting mode. Normal operation is in stereo mode.
On a preset, the stereo/mono setting is saved for
that preset.
Selecting the desired tuner
TUNER 1
TUNER 2
To control a tuner, push
or
. When
pressed, these buttons will be backlit green for Tuner
1 (XM) and amber for Tuner 2 (AM/FM). Each time a
tuner is selected the display will refresh with the cur-
rent station or preset for that tuner, and all subse-
quent button presses and memory preset entries will
be associated with that selected tuner.
Selecting Distant or Local Reception
(AM/FM only)
LOC/
DX
Press
to toggle between Distant and Local
mode. DISTANT or LOCAL appears briefly on the
screen when selecting mode. Normal operation is in
Distant mode.
Selecting the desired band (AM/FM only)
AM/FM
Push
to switch between AM and FM reception.
Recalling a Memory Preset
Selecting the desired frequency or channel
To recall a memory preset, select the desired tuner,
BANK
press
and enter the desired bank number
Use
and
for manual tuning. To move quickly
through the stations or channels, press and hold
either of the Tune buttons for more than 1.5 seconds.
M
EM
(1-6), then press
and enter the desired preset
number (1 to 6). The memory presets can also be
MEM
TUNE
To directly select a station or channel, press
,
MEM
accessed by using
and
to scroll through all
and enter the two- or three-digit XM channel number,
or the three- or four-digit station frequency (1071 for
107.1, etc.). European regions use five-digit station
frequencies.
presets for the selected bank.
Saving Favorites
The remote control stores two “favorites” (similar to
memory presets) per tuner. These are set simply by
selecting either Tuner 1 or Tuner 2, setting the
Selecting a mode (XM)
OK
FAV 1
Push
to select an XM operating mode.
desired frequency and pressing and holding
or
FAV 2
Exiting a mode (XM)
until “FAV1 (2) saved” appears on the tuner.
Stored Favorites are then recalled by pressing either
ST/
MONO
Push
to exit the XM operating mode selection
FAV 1
FAV 2
menu.
or
.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
ST2-KP KEYPAD CONTROLS
ST2-KP Keypad Operation
4
Selecting a Bank
To select a bank, select the desired tuner, then press
1
Turning the keypad on/off
and hold or to select the desired bank. The
bank name will show on the display.
To activate the ST2-KP, press
power down the keypad display. The keypad remains
powered until the ST2-XM Tuner is turned off.
. Press
to
4
Recalling a Memory Preset
1
Selecting the desired tuner
To recall a memory preset, press and release
or
To select a different tuner, press and hold
. (If the
keypad has been hardware jumper-selected to Tuner
1 or Tuner 2, it will not switch between the two
tuners.) The backlight color of the display will be
green for Tuner 1 (XM) and amber for Tuner 2
(AM/FM). Each time a tuner is selected the display
will refresh with the current station or preset for that
tuner, and all subsequent button presses and memo-
ry preset entries will be associated with that selected
tuner.
to scroll through the presets for the selected
bank. (Memory presets must be stored for ST2-KP
recall)
5
ST2-KP Keypad Display
The 5-character backlit display shows frequency and
band, plus XM channel and mode information.
Messages scroll twice, then display the first 5 char-
acters.
2
Selecting the desired band (AM/FM)
Push
to switch between AM or FM band.
ST2-KP Keypad-Front Panel
2
Selecting a mode (XM)
Push
to select an XM operating mode.
2
Exiting a mode (XM)
Press and release
the XM operating mode menu.
until EXIT is displayed to exit
5
3
Selecting the desired frequency or
channel
3
2
Use
and
for manual tuning. To move quickly
or
3
through the channels, press and hold either
1
for more than 1.5 seconds. European frequen-
cies show in .05 MHz increments.
4
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
UNO-S2 KEYPAD CONTROLS WITH CAV6.6
Frequency Seek (AM/FM only)
A press on will seek the next higher tune-
able station. If a tuneable station is not found,
CAV6.6-UNO-S2 Keypad Operation
NOTE: To control the ST2 Tuner through the
UNO-S2 keypad, the tuner must be configured
as a source using the CAV6.6 programming
steps.
end the SEEK function by pressing
Frequency Scan (AM/FM only)
To scan, press and hold then release
again.
Turning the unit on
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the UNO-S2 keypad will
bring the tuner out of standby mode.
. The
tuner scans through tuned stations with a 5-sec-
ond preview before moving to the next station.
Selecting the desired tuner
To end scanning, press
again.
On the UNO-S2 keypad, press
to select
Signal Strength Mode (XM)
either Tuner 1 (XM) or Tuner 2 (AM/FM) by
choosing the tuner’s preassigned source num-
ber.
To check XM signal strength, press and hold
then release. The display shows the signal
strength rating. To exit, press
Selecting a Bank
again.
Selecting the desired band (AM/FM only)
Push
to toggle between AM band and FM
To select a bank, press and hold
for bank
band reception.
up or
for bank down. The bank’s name will
Selecting a Mode (XM)
be temporarily displayed on the UNO-S2.
Push
to toggle between XM modes.
Recalling a Memory Preset
Exiting a Mode (XM)
Press
and
to scroll through the memo-
Press
until EXIT is displayed to
and release
ry presets for the selected bank. This procedure
will step through all of the presets in the current
bank, then loop back to start at the first one.
Only configured presets will be displayed.
exit XM mode selection menu.
Selecting the desired frequency or channel
Use
and
for manual tuning or channel
selection. The frequency or channel will appear
on the keypad and the active tuner. To move
quickly through the channels, press and hold
Mute
Press
to mute/unmute the tuner audio output.
either
or
for more than 1.5 seconds.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
UNO-S2 KEYPAD CONTROLS WITH CAV6.6
1
6
5
2
4
3
1
2
3
4
SCAN - (press and hold)
TUNER SELECTION - Select source number
assigned to TUNER 1 (XM) or TUNER 2 (AM/FM)
(AM/FM) Scans through tuned stations with
5-second preview before next station
(XM) Signal Strength mode toggle
TUNE UP/DOWN - Used for manual station or
channel selection
5
6
MUTE - Mutes/unmutes tuner audio output
SELECT -
BANK SELECT - Used for bank selection (press
and hold)
(AM/FM) Selects AM or FM band
(XM) Operating mode toggle
6
MEM UP/DOWN - Scrolls through memory preset
stations (press)
4
SEEK - (press)
(AM/FM) Seeks next higher tuned station
(XM) Exit current XM mode
NOTE: UNO-S2 keypads are connected to the
CAV6.6 to control the ST2-XM through RNET.
UNO-S2 keypads do not connect directly to
the ST2 Tuner.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
UNO-LRC1 REMOTE CONTROL WITH CAV6.6
digit station frequencies.
UNO-LRC1 Remote Control Operation
Turning the unit on
Frequency Seek (AM/FM only)
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the UNO-LRC1 will bring
the tuner out of standby mode when used with the
UNO keypad.
The SEEK function is performed by pressing and
releasing the Select
or
or
. Press
. To seek
for
higher frequency station press
Selecting the desired tuner
lower frequencies. Tuning begins at the current fre-
quency, seeks upward (or downward) and stops at the
To select a tuner, push
and choose the source
number preassigned to Tuner 1 (XM) or Tuner 2
(AM/FM), or use the UNO numeric source inputs at
the bottom of the UNO-LRC1.
next tuned station. Pushing
or
again con-
tinues the SEEK function. Once the highest frequency
is reached, the tuner continues SEEK mode at the
lowest frequency.
Selecting the desired band (AM/FM only)
Frequency Scan (AM/FM only)
Push
to toggle between AM/FM reception.
To scan, press and hold then release
. The
Selecting a Mode (XM)
tuner scans through tuned stations with a 5-second
preview before moving to the next station. To end
Push
,
or
to toggle between XM
operating modes.
scanning, press
again.
Exiting a Mode (XM)
Selecting a Bank
Press
or
to exit XM operating mode menu.
To select a bank, press and hold
or for bank down.
for bank up
to scroll
Signal Strength mode (XM)
Press and hold
and release. The display shows
the signal strength rating. To exit press
.
Recalling a Memory Preset
Selecting the desired frequency or channel
Press
and
or
and
Use the Channel
and
or
and
through a loop of all the memory presets for the cur-
rently selected bank. Only configured presets will be
displayed.
for manual tuning. To move quickly through the
channels, press and hold the button for more than
1.5 seconds. To directly select a station or channel,
enter the three- or four-digit channel or frequency
(1071 for 107.1, etc.). European regions use five-
Mute
Press the
button to mute/unmute the tuner
audio output.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM OPERATION
UNO-LRC1 REMOTE CONTROL WITH CAV6.6
1
2
POWER - Power managed by CAV6.6
UNO SELECTION - UNO must be the
selected source for control of the
CAV6.6 and any connected compo-
nents. Select UNO before sending
UNO-LRC1 remote commands.
NUMERIC INPUT - Number buttons for direct
input of frequency, channel, preset, bank
3
TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations
4
5
EXIT - Exit XM operating mode
1
2
TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations
6
SELECT -
(AM/FM) Confirms numeric selection
(XM) Operating mode toggle
7
8
MENU - XM operating mode toggle
PLAY -
(AM/FM) Selects AM or FM band
(XM) Operating mode toggle
3
4
9
9
BANK UP/DOWN - Used for bank selection (press
and hold)
12
15
5
6
5
7
8
MEM UP/DOWN - Scrolls through memory pre-
sets for selected bank (press)
14
13
10
11
MUTE - Mutes/unmutes tuner audio output
SCAN - (SEEK - press, see #14 below)
(AM/FM) Scans through tuned stations with 5-
second preview before next station (press and
hold)
9
12
(XM) Exit XM operating mode
10
12
TUNER SELECTION - Select source number
assigned to TUNER 1 (XM) or TUNER 2 (AM/FM)
11
13
14
INFO - XM Now Playing mode toggle
SEEK UP/DOWN -
(AM/FM) Seeks next tuned station up/down
(XM) Next/previous preset, category, info item,
display preference
15
GUIDE - XM Category Search mode toggle
25
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
ST2-XM Tuner Setup Menus
Note: The Setup Menu procedures must be performed from the ST2-XM Tuner front panel.
The ST2-XM Tuner Setup Menus provide setup and naming procedures for the ST2-XM main chassis,
the XM tuner module and the AM/FM tuner module. These procedures include source number assign-
ments, assigning a custom name to a memory preset or a bank, choosing a region for AM/FM opera-
tion (US or Euro), factory initialization and system information.
If the ST2-XM is used with a non-RNET system, the ST2-XM can be connected and operated without
any setup programming. Follow the setup menus if custom names are desired, or for system info.
If the ST2-XM is used with an RNET system such as CAV6.6, the following minimum setup must be
performed for the ST2-XM to be properly controlled by the CAV6.6.
1. ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.
2. CAV6.6 Source Setup Menu - Assign the corresponding source numbers to Tuner 1 and Tuner 2.
3. CAV6.6 Source Setup Menu - Assign command type PERIPHERAL to Tuner 1 and Tuner 2.
NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then
to the CAV6.6 (must be powered on last) to establish a connection.
9. Press TNR SEL to exit the Source Number
ST2 Chassis Setup Menu
menu.
Source Number (Chassis)
The Source Number procedure permits Tuner 1
Update Firmware (Chassis)
The Update Firmware procedure allows the ST2
tuner’s OS firmware to be updated. The proce-
dure is performed using a DB9 serial cable with
(XM) and Tuner 2 (AM/FM) to be assigned the
proper peripheral source identities as will be
assigned in the CAV6.6 Source Setup.
1. Enter the Setup Menu by pressing and holding one end connected to the RS-232 port on the
the TNR SEL button.
back of the tuner and the other connected to a
PC or laptop. If an OS firmware update is avail-
able, it can be obtained through the Document
2. TUNER SETUP appears. Press MEM Up/Down
until SOURCE NUM appears on the tuner.
3. Press BAND. TUNER # appears.
4. Press the Tune Up/Down buttons to select the firmware must be performed by an authorized
Tuner # (Tuner 1 is XM, Tuner 2 is AM/FM).
5. Press BAND. SOURCE NUM appears.
6. Press the Tune Up/Down buttons to scroll
through the source numbers 1-6.
Russound service facility.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
7. Press BAND to select the source number (as
assigned in the CAV6.6 setup process).
8. Repeat the process for the next tuner.
2. TUNER SETUP appears. Press MEM Up/Down
until UPDATE FIRMW appears on the tuner.
3. Press BAND to enter the UPDATE FIRMW menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press and Hold
TNR SEL button
ST2 Chassis Setup Procedures
TNR
SEL
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
Chassis
Setup
Menu
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
TNR
SEL
TNR
SEL
This
Procedure
returns the
ST2 Tuner
to its
HOLD
BAND
TUNER
#
Factory
settings
After update
cycle Power
Are you sure
SOURCE
NUM
Start
Update
YES
NO
Cycle Power
Please wait
Cycle Power
4. “Hold BAND” appears on the tuner.
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until FACTORY INIT appears on the tuner.
5. While pressing and holding BAND, “After
update cycle power” appears on the tuner
display.
3. Press BAND to enter the FACTORY INIT menu.
6. When “Start Update” appears on the tuner dis- 4. “Are you sure” appears on the tuner. Using the
play, start the update program. “Finished”
Tune Up/Down buttons, view the “Yes” and “No”
appears on the computer screen when complete. selections.
7. Cycle power to the tuner.
5. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
6. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when com-
plete.
Factory Initialization (Chassis)
The Factory Initialization procedure allows the
erasure of all programmed settings and returns
them to the factory default settings.
7. Cycle power on the ST2-XM tuner.
1. Enter the Setup Menu by pressing and holding
27
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
3. Press BAND.
System Info (Chassis)
4. Press BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press BAND at “Version” to view.
9. Press TNR SEL to exit the System Info menu.
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
(END OF ST2 CHASSIS SETUP)
Press TNR SEL
button to select
XM Tuner
XM Setup Menu
Memory Name Procedure
TNR
SEL
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
Chassis
Setup
Menu
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
TNR
SEL
SYSTEM
INFO
Procedure
XM
Setup
Menu
MEM
NAME
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
DIAGNOSTICS
Procedure
FACTORY
INIT
Procedure
TNR
SEL
SAVE
CHANGES?
MEMORY
NAME
BANK #
MEMORY #
Selects
character
Selects
character
position
Repeat
for each
character
in name
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
Tuner Setup Menu for XM
It is important to select the desired tuner
(Tuner 1 for XM) using the TNR SEL button
BEFORE accessing the Tuner Setup Menus.
2. TUNER SETUP appears. Press BAND again.
3. MEMORY NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
Memory Name (XM)
6. Press the Tune Up/Down buttons to select the
A memory preset must be created and saved
before it can be named (see page 19). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
Bank #.
7. Press BAND to advance. Memory # appears.
8. Press the Tune Up/Down buttons to select a
Memory #.
(continued)
Press TNR SEL
button to select
XM Tuner
XM Setup Menu
Bank Name Procedure
TNR
SEL
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
Chassis
Setup
Menu
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
TNR
SEL
SYSTEM
INFO
Procedure
XM
Setup
Menu
MEM
NAME
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
DIAGNOSTICS
Procedure
FACTORY
INIT
Procedure
TNR
SEL
SAVE
CHANGES?
BANK
NAME
BANK #
Selects
character
Selects
character
position
Repeat
for each
character
in name
29
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Name menu returns to the Bank # prompt to
name other banks, or press TNR SEL to exit the
Bank Name menu.
Memory Name (XM) (continued)
9. Press BAND to advance. MEMORY NAME
appears again.
10. Press BAND to access the Memory Name
Controller ID (XM)
The Controller ID procedure is used to identify
the controller(s) that the XM tuner will
respond to.
entry screen.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character
position. Up to 12 characters can be entered
one by one. A blinking cursor indicates the place- Note: For the XM module that is installed in the
ment of the character being entered. ST2-XM chassis, “All Controllers” will be the
12. Press BAND when memory name is entered. default setting.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
Diagnostics (XM)
15. Press BAND to save memory name. The
Memory Name menu returns to the Memory #
prompt to name other presets, or press TNR
SEL to return to the Memory Name menu start.
The Diagnostics procedure is for factory
use only.
Factory Initialization (XM)
The Factory Initialization procedure allows the
erasure of all programmed settings of the XM
tuner and returns them to the factory default set-
tings.
Bank Name (XM)
A custom name can be assigned to each of the
six banks of Tuner 1 (XM).
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND. BANK NAME appears again.
8. Press BAND to access the Bank Name entry
screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until FACTORY INIT appears on the
tuner.
4. Press BAND to enter the FACTORY INIT menu.
5. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
selections.
6. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
7. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when com-
plete.
10. Press BAND when bank name is entered.
11. SAVE CHANGES will appear.
8. Cycle power on the ST2-XM tuner.
12. Press Tune Up/Down to select Yes or No.
13. Press BAND to save bank name. The Bank
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
(END OF XM TUNER SETUP)
System Info (XM)
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
Tuner Setup Menu for AM/FM
1. Enter the Setup Menu by pressing and holding It is important to select the desired tuner
the TNR SEL button.
(Tuner 2 for AM/FM) using the TNR SEL
button BEFORE accessing the Tuner Setup
Menus.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
3. Press BAND.
4. Press BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press BAND at “Version” to view.
9. Press TNR SEL to exit the System Info menu.
Memory Name (AM/FM)
A memory preset must be created and saved
before it can be named (see page 19). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
(continued)
XM Setup Menu
Controller, Diagnostics, Factory Initialization
and System Info Procedures
Press TNR SEL
button to select
XM Tuner
TNR
SEL
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
Chassis
Setup
Menu
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
TNR
SEL
SYSTEM
INFO
Procedure
MEM
NAME
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
DIAGNOSTICS
Procedure
FACTORY
INIT
Procedure
XM
Setup
Menu
TNR
SEL
All Contrlrs
This
Procedure
is for
Factory
use
This
Procedure
returns the
ST2 Tuner
to its
ONLY
Factory
settings
Are you
sure?
Yes or No
YES
NO
Please
Wait
Cycle Power
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
7. Press BAND. BANK NAME appears again.
8. Press BAND to access the Bank Name entry
screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
10. Press BAND when bank name is entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press BAND to save bank name. The Bank
Name menu returns to the Bank # prompt to
name other banks, or press TNR SEL to exit the
Bank Name menu.
Memory Name (AM/FM) (continued)
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND again.
3. MEMORY NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND to advance.
8. Press the Tune Up/Down buttons to select a
Memory #.
9. Press BAND to advance. MEMORY NAME
appears again.
10. Press BAND to access the Memory Name
entry screen.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character posi-
tion. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
12. Press BAND when memory name is entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press BAND to save memory name. The
Memory Name menu returns to the Memory #
prompt to name other presets, or press TNR
SEL to return to the Memory Name menu start.
Region (AM/FM)
The Region procedure assigns either US or Euro
to the tuner. The difference between the two is
that US FM frequencies operate in .2 MHz incre-
ments, while European FM frequencies operate in
.05 MHz increments.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until REGION appears on the tuner.
4. Press BAND.
5. Press the Tune Up/Down buttons to select
either US or EURO.
Bank Name (AM/FM)
A custom name can be assigned to each of the
six banks of Tuner 2 (AM/FM).
6. Press BAND to select. Press TNR SEL to exit
the REGION menu.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
(END OF AM/FM TUNER SETUP)
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
The backup and restore PC application “RNET
Backup” is available through the Document
a DB9 male-to-female cable and laptop or desk-
top PC.
Backup and Restore
Once all of the tuner settings are completed, it
may be advisable to create a backup of the pro-
grammed settings for future use. The backup will
then be available in case tuner settings need to
be restored.
Press TNR SEL
button to select
AM/FM Tuner
AM/FM Setup Menu
TNR
SEL
TNR
SEL
Chassis
Setup
Menu
SYSTEM
INFO
Procedure
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
TNR
SEL
REGION
Procedure
MEM
NAME
Procedure
AM/FM
Setup
Menu
BANK
NAME
Procedure
TNR
SEL
TNR
SEL
MEMORY
NAME
BANK #
MEMORY #
SAVE
CHANGES?
BANK
NAME
BANK #
Selects
character
Selects
character
Selects
character
position
Selects
character
position
Repeat
for each
character
in name
Repeat
for each
character
in name
SAVE
CHANGES?
33
Download from Www.Somanuals.com. All Manuals Search And Download.
ST2-XM TUNER PROGRAMMING
PROGRAMMING FOR CAV6.6 USE
NOTE: The CAV6.6 firmware must be version 2.00.01 or higher and UNO-S2
firmware must be version 3.00.01 or higher to control the ST2-XM Tuner. Use
the System Info Menu of the CAV6.6 to check the firmware version. If the
firmware is not the proper revision as noted here, visit the Document Center
To Program the CAV6.6 to operate with the ST2-XM Tuner:
(refer to the CAV6.6 Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the
UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (XM)
is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or XM). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note:
When the ST2-XM Tuner is used with the CAV6.6 or other RNET controller, it is configured as an
RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave
as a fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique
source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Key Function Note:
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” com-
mand type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and
will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATION
ST2-XM Smart Tuner
Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)
Weight: 7 lbs. (3.2kg)
Power Supply: 12VDC 1.5A
Frequency Range: AM 530 - 1710 kHz
FM 87.7 - 107.9 MHz
FM Antenna impedance: 75 ohm unbalanced
Impedance: 300 ohm balanced
AM
Sensitivity @ S/N: 20dB 55 dBu
Image rejection: 33dB
S/N ratio: 45 dB
FM
Sensitivity @ S/N: 30 dB 6dB max 12 dBu
Image rejection: 80 dB
S/N ratio: 60 dB
XM
XM Band: 2332.5 - 2345 MHz
XM Antenna: 50-ohm SMB connection
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology
incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE®
voice compression software included in this product is protected by intellectual property rights
including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this
or any other software contained in an XM radio is explicitly prohibited from attempting to copy,
decompile, reverse engineer, or disassemble the object code, or in any way convert the object code
into human-readable form. The software is licensed solely for use within this product.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY & REPAIR
The Russound ST2-XM is fully guaranteed against all defects in materials and workmanship for two
(2) years from the date of purchase. During this period, Russound will replace any defective parts and
correct any defect in workmanship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its written instructions. If
service is necessary, it must be performed by Russound. The unit must be returned to Russound at
the owner's expense and with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing by an agency or per-
son not specifically authorized in writing by Russound.
This Warranty does not cover:
• Damage caused by abuse, accident, misuse, negligence,
or improper installation or operation
• Power surges and lightning strikes
• Normal wear and maintenance
• Products that have been altered or modified
• Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed
Russound sells products only through authorized Dealers and Distributors to ensure that customers
obtain proper support and service. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will not be honored or serviced
under existing Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and
labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with
a note explaining the nature of service required. Be sure to pack the unit in a corrugated container
with at least three (3) inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number.
Write this number on the shipping label and ship to:
Russound
ATTN: Service
5 Forbes Road
Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and techniques become avail-
able, Russound/FMP, Inc. reserves the right to revise system specifications without notice.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
37
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
38
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Russound
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: [email protected]
28-1160
07/13/04
Copyright © 2004 Russound® All rights reserved.
All trademarks are property of their respective owners.
E. & O.E.
Download from Www.Somanuals.com. All Manuals Search And Download.
|