4-Source Multi-Zone Central
Audio Controller/Amplifiers
CA-Series
ROCK
JAZZ
R&B
CHILDRENS
Instruction Manual
VOLUME
•ON / OFF
•VOLUME
• SOURCE
SOURCE
STORE
POWER
REMOTE SENSOR
REMOTE SENSOR
CA-KP.2
CA-LCD
CA 6.4 6-Zone, 4-Source Central Controller/Amplifier
6
Z
O
N
E
—
4
S
O
U
R
C
E
C
E
N
T
R
A
L
C
O
N
T
R
O
L
L
E
R
/
A
M
P
L
I
F
I
E
R
ON
1
2
3
4
5
6
OFF
POWER
ZONE
CA 6.4
CA 4.4pi 4-Zone, 4-Source Central Controller/Amplifier
4
Z
O
N
E
—
4
S
O
U
R
C
E
C
E
N
T
R
A
L
C
O
N
T
R
O
L
L
E
R
/
A
M
P
L
I
F
I
E
R
ON
1
2
3
4
OFF
POWER
ZONE
CA 4.4pi
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Possible System Configurations . . . . . . . . . . . . . . . . . . . . .4
Unpacking and Warranty Card . . . . . . . . . . . . . . . . . . . . . .4
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Basic Planning and Layout Considerations . . . . . . . . . . . .5
Connection Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Rear Panel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Source Input Connections . . . . . . . . . . . . . . . . . . . . . . . . .6
Speaker Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Zone Pre-Amp Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
12-Volt Trigger Output . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Mute Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting the Infrared Components . . . . . . . . . . . . . . . .7
Connecting the IR Link . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Keypad Connections at Controller . . . . . . . . . . . . . . . . . . .8
Wiring Runs Up to 100 ft . . . . . . . . . . . . . . . . . . . . . . . . . .8
Wiring Runs from 100 to 200 ft . . . . . . . . . . . . . . . . . . . .8
Installing Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Punchdown Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installing the Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Setting the Keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Source Control Keypads Option . . . . . . . . . . . . . . . . . . . .10
SRM-2.1 Speaker Relay Module Option . . . . . . . . . . . . .10
Speaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Operating the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . .12
Operating the CA-KP.2 Keypad . . . . . . . . . . . . . . . . . . . .12
Operating the CA-LCD Keypad . . . . . . . . . . . . . . . . . . . . .13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Download from Www.Somanuals.com. All Manuals Search And Download.
3
PRODUCT OVERVIEW
Congratulations on your recent purchase of a Russound CA-Series multi-room controller. This four/six-zone, four-source,
multi-room controller is the heart of an affordable whole-house audio distribution system. High-current, stereo, power
amplifiers are built into the Russound CA allowing simple connections to each speaker in the system. Each zone is operated
by an intuitive, easy-to-use keypad that controls all the functions of the CA. The keypads also have a built-in infrared receiv-
er that allows remote commands for your source equipment to be routed through the CA.
The Russound CA is built with pride. Fidelity, Reliability and Quality are the primary objectives. Russound products are guaran-
teed to provide years of enjoyment. The CA is UL listed and CSA approved for your protection and peace of mind.
UNPACKING
POSSIBLE SYSTEM CONFIGURATIONS
Carefully unpack the unit and keep the original carton and
packing materials for future moving, shipment or long-term
storage. After opening the box, please check for any visible
signs of damage that were not apparent from the outside of
the box. If you do encounter what appears to be concealed
damage, please consult your Russound dealer before pro-
ceeding to further unpack or install the unit.
ZONE 3
Master Bedroom
ZONE 4
Guest Room
CASSETTE
CD
Make sure to save your sales receipt. Your receipt is extreme-
ly important to establish the duration of your limited
Warranty, and for insurance purposes.
SOURCE EQUIPMENT
Family Room
ZONE 1
Living Room
ZONE 2
Kitchen
TUNER
CD
CASSETTE
DSS
TUNER
(AudDioSSSignal)
CA4.4pi
Controller
Figure 1 - Four-Zones of CA4.4pi
ZONE 5
Childs Room
CASSETTE
ZONE 3
ZONE 4
Master Bedroom
Guest Room
CD
CD
SOURCE EQUIPMENT
Family Room
ZONE 1
Living Room
ZONE 2
Kitchen
ZONE 6
Patio
TUNER
CD
CASSETTE
DSS
TUNER
CD
(AudDioSSSignal)
CA6.4
Controller
Figure 2 - Six-Zones of CA6.4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
GETTING STARTED
TOOLS NEEDED
BASIC PLANNING AND LAYOUT CONSIDERATIONS
The following information will indicate some tools and
materials necessary for a complete installation:
• Where will the speakers be located?
• Where will the keypads be located?
• How will the wiring be routed to each location?
• Where is the source equipment located?
• Where is the CA controller going to be located?
• 4 twisted pair communication wire (commonly referred to
as CAT-5). This wire will be used to connect the keypads
in each zone to the controller. 16 Gauge minimum, 2
conductor CL3 rated wire. (Russound AW162CL3) This
wire is used for direct connection between the CA and
your speakers.
Speaker Wire Length Gauge of Speaker Wire
10-100 feet
100-150 feet
Over 150 feet
16 AWG
14 AWG
12 AWG
• 110 Punchdown tool (included)
• A small jewelers flat-head screwdriver (included)
• A medium sized flat-head screwdriver.
• Wire strippers and cutters
• Electric drill and a 1/2" x 6" drill bit
• A steel-wire fish tape
Keypad Control
Wire Type
Max Recommended
Wire Length
CAT-5
Russound MCW2418
100 feet
200 feet
• A keyhole saw
• Electrical junction boxes (6)
• A stud finder
CONNECTION TIPS
• Disconnect all power cords before connecting to the CA.
• Verify that all connections and polarity are correct.
• A screwdriver (cordless recommended)
• Misc. hand tools, nails & screws
• Cable staples
• Keep all power cords away from all signal cables to pre-
vent noise or humming.
If you have problems or you are not absolutely comfortable
with what you are doing, consult a professional carpenter,
electrician, or system installer.
• Choose reliable signal cables / patch cords.
• Label all wires with room location at both ends of the
wire.
• Take your time!!! Don't panic about the number of wires;
simply connect one at a time.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
REAR PANEL CONNECTIONS
Figure 3 - CA6.4 Rear Panel Connections
VOLTAGE SELECTOR
SWITCH
SOURCE INPUT
KEYPAD ZONE INPUT
CONNECTIONS
INPUT FROM KEYPADS
CA6.4
CD
NEWMARKET, NH U.S.A.
TAPE AUX
DESIGNED BY RUSSOUND
MADE IN KOREA
TUNER
6
5
4
3
2
1
~220-240VAC
~110VAC
R
L
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OUTPUT TO 8Ω SPEAKERS
6
5
4
3
2
1
WARNING : SHOCK HAZARD –
DO NOT OPEN
AVIS : RISQUE DE CHOC
ELECTRIQUE – NES PAS OUVRIR.
VOLTAGE FUSE
110V F4A
220-240V F2A
12V
IR
IR REMOTE OUTPUT
TRIG
LINK
~110VAC
~220-240VAC
~50-60Hz
400W
SERIAL #
4
3
2
1
100 mA
PLUG-IN SEQUENCE
AC110/240
INPUT
FUSE
EMITTER
SPEAKER OUTPUT
CONNECTORS
12V TRIGGER
OUTPUT
HOLDER
OUTPUTS
IR LINK
Figure 4 - CA4.4pi Rear Panel Connections
VOLTAGE SELECTOR
SWITCH
SOURCE INPUT
KEYPAD ZONE INPUT
ZONE PREAMP OUTPUTS
CONNECTIONS
INPUT FROM KEYPADS
CA4.4
CD
NEWMARKET, NH U.S.A.
TAPE AUX
ZONE PREAMP OUTPUTS
TUNER
4
3
2
1
~220-240VAC
~110VAC
R
L
R
L
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
OUTPUT TO 8Ω SPEAKERS
WARNING : SHOCK HAZARD –
DO NOT OPEN
AVIS : RISQUE DE CHOC
ELECTRIQUE – NES PAS OUVRIR.
VOLTAGE FUSE
4
3
2
1
4
3
2
1
12V
IR
110V
F4A
IR REMOTE OUTPUT
220-240V F2A
TRIG LINK
~110VAC
~220-240VAC
~50-60Hz
400W
TELE-
PHONE
DOOR
BELL
SERIAL #
MUTE
INPUT
4
3
2
1
100mA
USE #1 FIRST
AC110/240
INPUT
FUSE
EMITTER
SPEAKER OUTPUT
CONNECTORS
12V TRIGGER
OUTPUT
HOLDER
MUTE INPUTS
OUTPUTS
IR LINK
SOURCE INPUT CONNECTIONS
SPEAKER CONNECTIONS
Your source inputs are located at the top left corner of the
back panel. Although the source input names are silk
screened on the back of the CA, these names are for refer-
ence only. Any type of source equipment can be connected
to any input. Connect each source output, left and right,
using quality signal cables / patch cables. Label each cable
the name of your source and the input number of the CA
you have selected. Repeat until all sources are connected.
List them down below.
Each speaker connection on the back panel corresponds to
one room/zone. Wire your speakers by first removing the
connector for the chosen zone. Using wire strippers, strip
back 1/4" of the end of the wire. Insert the proper polarity,
left + to left +, left- to left- etc., until all wires are connect-
ed in each zone output. Label each wire with the room name
and zone number. Write down the room name to the zone
number below. Note: We recommend 8 Ohm minimum
speakers for each zone. However, speakers as low as 4 Ohm
can be safely used in up to two zones, if necessary.
List 1 – Source names should be written below
List 2 – Wire color should be written below
Input 1 (TUNER) ____________ Input 2 (CD) ____________
Input 3 (TAPE) ____________ Input 4 (AUX) ____________
(Color) Left + _______________ Left - _______________
Right + _______________ Right - _______________
List 3 – Room names should be written below
Zone 1 ________________ Zone 2 ________________
Zone 3 ________________ Zone 4 ________________
Download from Www.Somanuals.com. All Manuals Search And Download.
6
REAR PANEL CONNECTIONS
ZONE PRE-AMP OUTPUTS (CA4.4PI ONLY)
CONNECTING THE INFRARED COMPONENTS
In applications where more power than the 20 watts per
• In order for your CA to transmit the IR signal from the
channel is desired, connect one or more zones of the CA4.4pi
to an external amplifier. Using standard RCA connectors,
wire from the pre-amp outputs of the CA4.4pi to the ampli-
fier's inputs. A typical application for more power is when
connecting an outside zone where the audio power require-
ments would be much greater than an inside zone.
keypads to a source, an emitter must be connected from
the IR outputs marked 1-4. Each of these outputs is wired
in series and must be connected in consecutive order. For
example, the #1 emitter output must be connected in
order for the #2 emitter output to transmit the IR com-
mand. NOTE: All IR outputs are common
• Connect each 845.1 mini-emitter to the IR output.
Figure 5 - Zone Pre-amp Output Connection
• Remove the adhesive back and position the IR receiver on
the product you wish to control. Stick the 845.1 emitter
directly over the source components IR window.
ZONE PREAMP OUTPUTS
R
CD PLAYER
L
Figure 8 - IR Emitter Connections
4
3
2
1
845
EMITTER
CASSETTE DECK
845
EMITTER
REAR OF
12-VOLT TRIGGER OUTPUT
TUNER
CA UNIT
The 12 volt trigger is engaged when any of the zones are on
and disengaged when the last zone is turned off. The trigger
can be used to engage any 12 volt triggered accessory, such
as a triggered AC outlet or audio amplifier. The connection
for the trigger is made through an 1/8” male mini-plug jack.
The tip is (+) and sleeve is (-).
845
EMITTER
TO OTHER SOURCE
845
EMITTER
IR REMODULATOR 56K (INCLUDED ACCESSORY)
CA IR REMOTE OUTPUT
CA KEYPAD PORT
The IR Remodulator
56K converts 40KHz IR
signals to 56KHz. The
IR Remodulator takes
a 40KHz IR signal that
comes from the IR
remote output of the
CA system and remod-
ulates it at 56KHz.
Figure 6 - 12-Volt Trigger Output Connection
IR REMOTE OUTPUT
1
2
3
4
5
6
7
8
3
2
1
Red
12V
TRIG
56KHz
40KHz
Model # 845.1 Emitter
DVD
MUTE INPUT (CA4.4PI ONLY)
This allows some com-
ponents that may only
accept 56KHz to be
When used with the optional Doorbell or Telephone inter-
face, the Mute Input mutes the audio to the speakers for six
seconds when either the doorbell is used or when the tele-
phone rings. The connection for the Mute Input is made
through a 1/8” male mini-plug. The tip is (+) and the sleeve
is (-).
remotely controlled with optimum performance. Refer to IR
56K Remodulator Instruction Manual for full connection
instructions.
CONNECTING THE IR LINK
Figure 7 - DIM-1 Doorbell Interface Module
DOORBELL INTERFACE
12VDC Power In
POWER
When two CA Controllers are to be used in an installation,
the IR Link connection is used to pass IR signal between the
two units. Use a 1/8” mini-plug, male-to-male cable (includ-
ed) connected from the IR Link on the first CA Controller to
the IR Link on the second CA. When connected, you may
connect your IR emitters to either CA unit’s IR Remote
Output jacks.
+12V DC
TRIG
To Trigger Input on CA4.4pi
To Doorbell Chime
Download from Www.Somanuals.com. All Manuals Search And Download.
7
KEYPAD CONNECTIONS AT CONTROLLER
• Each keypad connection on the back panel of the CA-Series Master
List 4 – Room names should be written below.
Controller corresponds to the room / zone number chosen for your
speakers. Each zone operates independently, so it is very important to
connect the keypad to the correct zone keypad input.
Zone 1 _________________
Zone 2 _________________
Zone 3 _________________
Zone 4 _________________
• On List 4 (opposite) copy down the room name to the zone number
from List 3 on pg 6. NOTE: the keypad and the speakers in each room
must be hooked to the corresponding numbered zone.
• Remove the connector and strip 1/8" off each end of the wire insula-
tion. Connect each wire 1 thru 8 using a small jewelers screwdriver.
WIRING RUNS UP TO 100 FEET
WIRING RUNS FROM 100-200 FEET
For wiring runs of up to 100 feet in length, we recommend
the use of CAT-5 wire. It is inexpensive and color coded for
ease of installation. Due to the qualities of CAT-5 wire, when
using it for keypad control wire with the CA-Series, it is rec-
ommended to use the following color code for maximum
performance.
For wiring runs exceeding 100 feet and extending up to 200
feet, we recommend the use of 8-conductor 22 AWG strand-
ed wire such as Russound MCW2418.
If using 22 AWG wire, the order in which you wire is not
important as long as you wire in the same order at both the
CA unit as well as the keypad. Use List 5 (below) to write
down the wire you use for each pin number.
CAT-5
Brown/White
Brown
Green
Orange/White
Orange
Green/White
Blue/White
Blue
Number
Type
Ground
IR Signal
1
2
3
4
5
6
7
8
NOTE: Wiring runs longer than 200 feet are not recommend-
ed for the CA-Series Keypads.
12VDC+
Source Select
Source Select
Channel Select
Volume
List 5 –Wire color should be written below.
Pin 1 _______________ Pin 2 _______________
Pin 3 _______________ Pin 4 _______________
Pin 5 _______________ Pin 6 _______________
Pin 7 _______________ Pin 8 _______________
Balance
Figure 9 – Connections with CAT-5 wire
INPUT FROM KEYPADS
4
3
Figure 10 – Connections with 22AWG wire
INPUT FROM KEYPADS
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
4
3
CAT-5 WIRE
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
8 CONDUCTOR
22AWG STRANDED WIRE
Download from Www.Somanuals.com. All Manuals Search And Download.
8
INSTALLING KEYPADS
PUNCHDOWN TERMINALS
INSTALLING THE KEYPADS
Figure 11 – Punchdown
Terminal on CA-KP.2
and CA-LCD
• The best infrared remote performance is achieved with
the keypad away from any direct sunlight. Also consider
convenience when choosing a location.
• Choose a place that is easily seen from the position where
a person is most likely to be located.
2
1
3
6
5
4
8
7
• Check whether or not you can route the wire to the loca-
tion you have chosen.
• Purchase retro-fit plastic junction boxes (min. 20 cubic
inches) or p-rings and cut in the boxes using a key-hole
saw or sheetrock knife/hand saw.
The CA-KP.2 and CA-LCD come with 110 punchdown termi-
nals. These terminals are quick, easy to install and provide a
strong connection. Punchdown terminals require the use of a
punchdown tool. One has been provided with this kit.
• If you are installing the optional DSC keypad you will
need to use a double-gang electrical box. If you are
installing the CA-LCD, DSC and the optional DAN keypad
you will need to install a triple-gang electrical box.
Press wires into punchdown terminal with punchdown tool
as shown in Figure 12.
• If you feel uncomfortable cutting into your walls and
running wire through the walls, seek help from a profes-
sional installer or an electrician.
Figure 12 – Punching Down Wires
• Route the wire to the junction box from the CA location.
• If using 22 AWG wire, connect each wire to the correct
position 1 thru 8 using the included punchdown tool.
Refer to List 5.
Punchdown
Tool
• If using CAT-5 wire, connect each wire to its correspon-
ding color labeled on the punchdown terminal.
2
1
3
L
VO
• Mount the keypad in the junction box and attach the
Decora plate.
BAL
SEL1
SEL3
IR
+12V
GND
CHSEL
• The CA-KP.2 keypad has source labels for your conven-
ience. Insert the label in the keypad keeping the input
number in sequence with the source selected.
• Repeat the above steps until all keypads are installed.
2
1
3
6
5
4
8
7
Connector on
CA-KP.2 or CA-LCD
CAT-5 or 8-conductor
22 AWG wire
Download from Www.Somanuals.com. All Manuals Search And Download.
9
INSTALLING KEYPADS
SETTING THE KEYPADS
SRM-2.1 SPEAKER RELAY MODULE OPTION
Before a keypad is installed into the j-box, turn on the
power so that you can operate the keypad.
The optional SRM-2.1 module works with CA-LCD keypad’s
12V trigger output. This unobtrusive wall-mount device
allows you to automatically switch to whole house audio in
a zone containing existing audio equipment. Example: In a
bedroom with a stereo system, the stereo system would be
the default. When you turn on the bedroom's zone at the
keypad the whole house audio system takes control of the
existing stereo speakers.
CA-LCD Only: The amber and the green backlight brightness
can be individually set. Note the brightness controls are
located on the side of the keypad. Adjust to the desired
brightness the backlight that first comes on. Press and hold
the lamp button on the front of the keypad until the back-
light switches to the other color. Adjust the brightness for
the selected color.
If you are using the optional SRM-2.1 speaker relay module,
wire the +, - terminals of the CA-LCD to the SRM-2.1 +, -
terminals.
Both CA-LCD and CA-KP.2: The maximum volume and the
balance should also be set at this time.
Figure 15 – SRM-2.1 connection to CA-LCD
Figure 13 - Keypad Adjustments
CA-LCD
CA-KP.2
INPUT FOR LOCAL AMPLIFIED SIGNAL
IS FOUND ON FRONT OF SRM-2.1
2
1
3
6
5
4
8
7
AMBER BRIGHTNESS
GREEN BRIGHTNESS
VOLUME
BALANCE
BALANCE
VOLUME
AMPLIFIED ZONE
INPUT FROM RUSSOUND
MULTI-ZONE SYSTEM
AMPLIFIED
OUTPUT TO
IN-WALL SPEAKERS
MORE
LESS
SRM-2.1
SOURCE CONTROL KEYPADS OPTION
The optional DSC and DAN source control keypads simply
dock into the side of either the CA-KP.2 or CA-LCD keypads
via a 16 prong jack. See DSC and/or DAN instruction manu-
als for programming instructions.
Refer to the SRM-2.1 Instruction Manual for complete
wiring directions.
Figure 14 - Installing the DSC or DAN
SEEK
MODE
SELECT
SCAN
2
5
8
0
1
4
3
6
VOLUME
7
9
SOURCE
ENTER
STORE
POWER
DIRECT ACCESS
NUMERIC SOURCE KEYPAD
DIRECT SOURCE CONTROL
REMOTE SENSOR
DAN
CA-LRN
DSC
Download from Www.Somanuals.com. All Manuals Search And Download.
10
SPEAKER INSTALLATION
SPEAKER INSTALLATION
• If you are installing in-wall speakers, follow the instruc-
tions provided with your speakers for mounting.
• Connect each speaker wire to the correct polarity (+,-).
Figure 16 - Wire Polarity
-
+
FINALLY!!!
• Make sure that the voltage selector, located on the rear
panel of the CA, is on the correct current for your
country, either 110V or 220V
• Power up by plugging in all power cords and turning
the CA and sources on.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
OPERATION
OPERATING THE MAIN UNIT
OPERATING THE CA KP.2 KEYPAD
• Power switch: When the power switch is engaged, the CA
power indicator will be lit an amber color. The CA should be
left on at all times. The unit will consume very little power
unless the zones are on and active. The unit has a stand-by
mode when the zones are inactive.
1) Power On / Off: This knob on the CA KP.2 keypad con-
trols all functions except for the IR management. To turn
the unit on, simply turn the control knob clockwise. You
will feel and hear a click verifying that the unit has been
activated. The lights on the keypad will also illuminate to
verify the zone is now on. Note - The CA front panel
zone-management lights also informs you which zones
are On or Off.
• Zone Indicators: The zone indicator will light either red
for off or green for on. The zones can only be turned on
from the keypads. All functions are accessed through the
keypad only.
2) Volume Up / Down: Once the unit is on, the knob can be
used to adjust the volume. To adjust the volume up, turn
the knob clockwise, and to turn the volume down, turn
counter-clockwise.
3) Source Selection: By pressing the knob, the zone will
scroll through the four sources connected to the CA. The
keypad has four backlit windows that indicate the source
selected.
4) IR Source Control: The IR window repeats all source com-
mands from the source component's remote (or optional
DSC/DAN keypads) through the CA and 845.1 emitters.
Most IR remotes have a range of 20' at an angle of 60-65
degrees.
Figure 17 - CA-KP.2 Keypad Functions
ROCK
JAZZ
R&B
1-Power On / Off
CHILDRENS
2-Volume Up / Down
3-Source Selection
4-IR Source Control
•ON / OFF
•VOLUME
• SOURCE
REMOTE SENSOR
Download from Www.Somanuals.com. All Manuals Search And Download.
12
OPERATION
OPERATING THE CA-LCD KEYPAD
Figure 18 - CA-LCD Keypad Functions
1) Display: The LCD panel displays the name of the source
selected and the volume level.
1-Display
2) Source: The source button is pressed to select one of the
four sources to listen to. Press the source button until the
desired source is selected. The source will be displayed on
the LCD display panel.
2-Source
3-Volume Up / Down
4-Lamp
3) Volume Up / Down: The UP / DOWN arrows for volume
are used to select the volume level and to select a differ-
ent source name after the store button is pressed. If the
button is pressed and held the volume will ramp up or
down.
VOLUME
SOURCE
5-Power
STORE
POWER
6-Store
4) Lamp: The lamp button when pressed and released will
turn on and off the backlight lamp. The backlight color
can be set to amber or green by pressing and holding the
button. The backlight will change from one color to the
other.
REMOTE SENSOR
7-IR Receiver
8-IR Confirmation LED
5) Power: Turn on or off any zone by pressing the power
button on the front of the corresponding keypad. When
the keypad comes on, it will automatically select the
source that was previously selected and set the volume to
minimum.
Figure 19 - CA-LCD RC Remote Control Functions
ROOM
ON
OFF
1
3
2
4
6) Store: The store function is used to select and store one
of the 23 preset source names for each of the four
sources. Select the source name that you want to change
by selecting source. Press and hold the store button for
approximately 3 seconds, and the display begins to flash.
Immediately press the UP/ DOWN volume buttons to
select the different source names. After you have selected
the name, press the store button again or wait for it to
stop flashing.
LISTENTO
SOURCE
VOLUME
VOLUME
SOURCE
CA LCD RC
STORE
POWER
REMOTE SENSOR
7) IR Receiver: The IR receiver is used to receive commands
from an IR remote control. Remote controls used for the
source equipment will pass through to the main con-
troller and on to the source equipment. It will receive IR
signals from 38KHz to 56KHz. To control the functions of
the CA-LCD keypad, use the CA Remote control (see
Figure 6). The CA remote control will operate the lamp,
source selection, volume up / down and room on / off.
8) IR Confirmation LED: This LED will flash to confirm the
reception of an IR signal from a remote control through
the IR receiver.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
SPECIFICATIONS
CA6.4
CA4.4pi
• Frequency Response: 20 Hz to 20 KHz ( +/- 1 dB )
• 20 Watts RMS / Channel @ 8Ω
• Frequency Response: 20 Hz to 20 KHz ( +/- 1 dB )
• 20 Watts RMS / Channel @ 8Ω
• 12 Channels / 6 Stereo Amplifiers
• 8 Channels / 4 Stereo Amplifiers
• Total Harmonic Distortion: .01%
• Total Harmonic Distortion: .01%
• Signal to Noise Ratio: 89 dB min, “A” weighted
• Power Supply: 110/220V High Current Torroidal
• Signal to Noise Ratio: 89 dB min, “A” weighted
• Power Supply: 110/220V High Current Torroidal
• ETL listed. Conforms to UL Standard UL1492 and CSA
Standard C22-2 No. 1-M94
• ETL listed. Conforms to UL Standard UL1492 and CSA
Standard C22-2 No. 1-M94
• Fully Functional Keypad with IR Receiver Centered at
40 kHz and 56K kHz
• Fully Functional Keypad with IR Receiver Centered at
40 kHz and 56K kHz
TROUBLESHOOTING
KEYPAD WIRING PROTECTION CIRCUIT
ELIMINATION OF BALANCE LINE
To provide protection for incorrect keypad wiring, this CA-
Series product is equipped with a short circuit protection
device. In the event of a keypad cable short, or incorrect
keypad wiring, this device will automatically interrupt power
to all keypad ports.
The following diagram shows how resistors may be used at
the Keypad connection on the rear of the CA master control
unit, to provide 2.5VDC to the balance control line for cen-
tering. This circuit will stabilize the balance line input and
keep it centered. They can be used to free up one of the 8
required conductors if one is open, shorted or if an extra
conductor is needed for a secondary IR receiver’s signal in
that zone. Position #1 is GND, #3 is 12VDC, #8 is Balance.
Once installed, if the keypads connected to your CA-Series
product will not turn on, the short circuit protection device
may have been activated. Please take the following steps to
troubleshoot the system.
CA Keypad Connector @ Rear of Processor
1) Turn off the power switch on the front of the CA-Series
controller.
820 Ohm 1/4w
3.9K Ohm 1/4w
2) Disconnect all keypad connections from the rear of the
controller.
3) Check the wiring configuration for each keypad, checking
both ends (the CA unit and the CA keypads) of the CAT-5
keypad cable.
4) If incorrect connections were found, correct the wiring
and reconnect the keypads to the controller. After the
controller has been powered off for at least 15 seconds,
turn on the power switch of the CA-Series controller.
1
2
3
4
5
6
7
8
5) If the problem persists, repeat steps above trying each
keypad consecutively.
Balance
+12VDC
GND
6) Inadequate ventilation can allow normal heat to build up
and trip the protection circuit.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
TROUBLESHOOTING
COMBINING ADDITIONAL IR RECEIVERS
When combining a CA Series multi-source controller and a
secondary IR system together, it needs to be done after the
CA System. The IR information from the keypad is on Pin #2.
This signal is demodulated at the keypad and is re-modulat-
ed at the processor then sent to the emitter out-puts.
Combining a modulated IR signal to this lead (#2) will not
work because it is already modulated. The following method
should be used to assure correct integration with such com-
ponents.
IR REMOTE OUTPUT
4
3
2
1
PLUG-IN SEQUENCE
GROUND
SIGNAL
CONNECT TO
846C POWER
SUPPLY
TO SECOND
IR RECEIVER
The emitter outputs on the CA Series are wired in series, so
#1 must be used first in order to obtain a signal. Simply plug
the IR linking cable supplied with the CA product into emit-
ter port #1. and plug the other end into the Russound 857
IR Connecting Block’s “IR Common In”. The secondary IR
receiver can either be wired to the terminal block as shown
or plugged into the “IR Reciever In” via a 1/8” mini-plug. The
emitters that would have been connected directly to the CA
system will now be plugged into the connecting block.
L O C B K
O C N N E C T I N G
O N F I R I R M C
N I F R A R 8 E 5 D 7
M E I T T E R S
6
1
2
3
4
5
845.1 MICRO EMITTERS
TO IR CONTROLLED
EQUIPMENT
This method combines the modulated IR signal at the con-
necting block then distributes it to the four emitter ports.
The power supply shown (846C) would only be required if
the second IR receiver(s) needed it.
This method would also be used when connecting multiple
CA systems together. The IR Link is only designed for two CA
systems being that it conveys demodulated IR data between
the systems.
WARRANTY
The Russound CA-Series Controllers are fully guaranteed for Two (2) years from the date of purchase against all defects in
materials and workmanship. During this period Russound will replace any defective parts and correct any defect in workman-
ship without charge for either parts or labor. For this warranty to apply, the unit must be installed and used according to its
written instructions. If service is necessary, it must be performed by Russound. The unit must be returned to Russound at the
owners expense and with prior written permission. Accidental damage and shipping damage are not considered defects under
the terms of the warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an
agency or person not specifically authorized in writing by Russound. Damage to or destruction of components due to
improper use voids the warranty. In these cases the repair will be made at the owners expense. To return for repairs, the unit
must be shipped to Russound at the owners expense, along with a note explaining the nature of the service required. Be sure
to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
A
/
V
D
I
S
T
R
I
B
U
T
I
O
N
&
C
O
N
T
R
O
L
S
Y
S
T
E
M
S
5 Forbes Rd. Newmarket, NH 03857
☎ 603.659.5170 • Fax 603.659.5388
e-mail: [email protected]
Fax-On-Demand: 603.659.5590
Come visit us at:
28-1116 R6
Download from Www.Somanuals.com. All Manuals Search And Download.
|